Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Titus Rwantare <titusr@google.com>
Message-Id: <20220701000626.77395-2-me@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This commit adds support for DMA RX in slave mode while using the new
register set in the AST2600 and AST1030. This patch also pretty much
assumes packet mode is enabled, I'm not sure if this will work in DMA
step mode.
This is particularly useful for testing IPMB exchanges between Zephyr
and external devices, which requires multi-master I2C support and DMA in
the new register mode, because the Zephyr drivers from Aspeed use DMA in
the new mode by default. The Zephyr drivers are also using packet mode.
The typical sequence of events for receiving data in DMA slave + packet
mode is that the Zephyr firmware will configure the slave address
register with an address to receive on and configure the bus's function
control register to enable master mode and slave mode simultaneously at
startup, before any transfers are initiated.
RX DMA is enabled in the slave mode command register, and the slave RX
DMA buffer address and slave RX DMA buffer length are set. TX DMA is not
covered in this patch.
When the Aspeed I2C controller receives data from some other I2C master,
it will reset the I2CS_DMA_LEN RX_LEN value to zero, then buffer
incoming data in the RX DMA buffer while incrementing the I2CC_DMA_ADDR
address counter and decrementing the I2CC_DMA_LEN counter. It will also
update the I2CS_DMA_LEN RX_LEN value along the way.
Once all the data has been received, the bus controller will raise an
interrupt indicating a packet command was completed, the slave address
matched, a normal stop condition was seen, and the transfer was an RX
operation.
If the master sent a NACK instead of a normal stop condition, or the
transfer timed out, then a slightly different set of interrupt status
values would be set. Those conditions are not handled in this commit.
The Zephyr firmware then collects data from the RX DMA buffer and clears
the status register by writing the PKT_MODE_EN bit to the status
register. In packet mode, clearing the packet mode interrupt enable bit
also clears most of the other interrupt bits automatically (except for a
few bits above it).
Note: if the master transmit or receive functions were in use
simultaneously with the slave mode receive functionality, then the
master mode functions may have raised the interrupt line for the bus
before the DMA slave transfer is complete. It's important to have the
slave's interrupt status register clear throughout the receive
operation, and if the slave attempts to raise the interrupt before the
master interrupt status is cleared, then it needs to re-raise the
interrupt once the master interrupt status is cleared. (And vice-versa).
That's why in this commit, when the master interrupt status is cleared
and the interrupt line is lowered, we call the slave interrupt _raise_
function, to see if the interrupt was pending. (And again, vice-versa).
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Message-Id: <20220630045133.32251-8-me@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Add slave mode functionality for the Aspeed I2C controller in old
register mode. This is implemented by realizing an I2C slave device
owned by the I2C controller and attached to its own bus.
The I2C slave device only implements asynchronous sends on the bus, so
slaves not supporting that will not be able to communicate with it.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
[ clg: checkpatch fixes ]
Message-Id: <20220601210831.67259-6-its@irrelevant.dk>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220630045133.32251-7-me@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Add an asynchronous version of i2c_send() that requires the slave to
explicitly acknowledge on the bus with i2c_ack().
The current master must use the new i2c_start_send_async() to indicate
that it wants to do an asynchronous transfer. This allows the i2c core
to check if the target slave supports this or not. This approach relies
on adding a new enum i2c_event member, which is why a bunch of other
devices needs changes in their event handling switches.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Message-Id: <20220601210831.67259-5-its@irrelevant.dk>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220630045133.32251-6-me@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Allow slaves to master the bus by registering a bottom halve. If the bus
is busy, the bottom half is queued up. When a slave has succesfully
mastered the bus, the bottom half is scheduled.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
[ clg : - fixed typos in commit log ]
Message-Id: <20220601210831.67259-4-its@irrelevant.dk>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220630045133.32251-5-me@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Add support for writing and reading the device address register in old
register mode.
On the AST2400 (only 1 slave address)
* no upper bits
On the AST2500 (2 possible slave addresses),
* bit[31] : Slave Address match indicator
* bit[30] : Slave Address Receiving pending
On the AST2600 (3 possible slave addresses),
* bit[31-30] : Slave Address match indicator
* bit[29] : Slave Address Receiving pending
The model could be more precise to take into account all fields but
since the Linux driver is masking the register value being set, it
should be fine. See commit 3fb2e2aeafb2 ("i2c: aspeed: disable
additional device addresses on ast2[56]xx") from Zeiv. This can be
addressed later.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
[ clg: add details to commit log ]
Message-Id: <20220601210831.67259-3-its@irrelevant.dk>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Moves register definitions and short commonly used inlined functiosn to
the header file to help tidy up the implementation file.
Signed-off-by: Joe Komlodi <komlodi@google.com>
Change-Id: I34dff7485b6bbe3c9482715ccd94dbd65dc5f324
Message-Id: <20220331043248.2237838-8-komlodi@google.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
On AST2600, I2C has a secondary mode, called "new mode", which changes
the layout of registers, adds some minor behavior changes, and
introduces a new way to transfer data called "packet mode".
Most of the bit positions of the fields are the same between old and new
mode, so we use SHARED_FIELD_XX macros to reuse most of the code between
the different modes.
For packet mode, most of the command behavior is the same compared to
other modes, but there are some minor changes to how interrupts are
handled compared to other modes.
Signed-off-by: Joe Komlodi <komlodi@google.com>
Change-Id: I072f8301964f623afc74af1fe50c12e5caef199e
Message-Id: <20220331043248.2237838-6-komlodi@google.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Using a register array will allow us to represent old-mode and new-mode
I2C registers by using the same underlying register array, instead of
adding an entire new set of variables to represent new mode.
As part of this, we also do additional cleanup to use ARRAY_FIELD_
macros instead of FIELD_ macros on registers.
Signed-off-by: Joe Komlodi <komlodi@google.com>
Change-Id: Ib94996b17c361b8490c042b43c99d8abc69332e3
[ clg: use of memset in aspeed_i2c_bus_reset() ]
Message-Id: <20220331043248.2237838-5-komlodi@google.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Leading underscores are ill-advised because such identifiers are
reserved. Trailing underscores are merely ugly. Strip both.
Our header guards commonly end in _H. Normalize the exceptions.
Macros should be ALL_CAPS. Normalize the exception.
Done with scripts/clean-header-guards.pl.
include/hw/xen/interface/ and tools/virtiofsd/ left alone, because
these were imported from Xen and libfuse respectively.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20220506134911.2856099-3-armbru@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Header guard symbols should match their file name to make guard
collisions less likely.
Cleaned up with scripts/clean-header-guards.pl, followed by some
renaming of new guard symbols picked by the script to better ones.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20220506134911.2856099-2-armbru@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
[Change to generated file ebpf/rss.bpf.skeleton.h backed out]
- add the VOUT_MIN and STATUS_MFR registers
Signed-off-by: Titus Rwantare <titusr@google.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Message-Id: <20220307200605.4001451-2-titusr@google.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Introduce an AspeedI2CBus SysBusDevice model and attach the associated
memory region and IRQ to the newly instantiated objects.
Before this change, the I2C bus IRQs were all attached to the
SysBusDevice model of the I2C controller. Adapt the AST2600 SoC
realize routine to take into account this change.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
QEMU has support for SMBus devices, and PMBus is a more specific
implementation of SMBus. The additions made in this commit makes it easier to
add new PMBus devices to QEMU.
https://pmbus.org/specification-archives/
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Signed-off-by: Titus Rwantare <titusr@google.com>
Message-Id: <20210708172556.1868139-2-titusr@google.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
To ease reviewing code using the I2C bus API, introduce the
i2c_start_recv() and i2c_start_send() helpers which don't
take the confusing 'is_recv' boolean argument.
Use these new helpers in the SMBus / AUX bus models.
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Make the argument representing the direction of the transfer a
boolean type.
Rename the boolean argument as 'is_recv' to match i2c_recv_send().
Document the function prototype.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <20200621145235.9E241745712@zero.eik.bme.hu>
[PMD: Split patch, added docstring]
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Other functions from I2C slave API are named "i2c_slave_XXX()".
Follow that pattern with set_address(). Add docstring along.
No logical change.
Patch created mechanically using:
$ sed -i s/i2c_set_slave_address/i2c_slave_set_address/ \
$(git grep -l i2c_set_slave_address)
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
We replaced all the i2c_send_recv() calls by the clearer i2c_recv()
and i2c_send(), so we can remove this confusing API.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
lm832x_key_event() is specific go LM832x devices, not to the
I2C bus API. Move it out of "i2c.h" to a new header.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The pca954x is an i2c mux, and this adds support for two variants of
this device: the pca9546 and pca9548.
This device is very common on BMCs to route a different channel to each
PCIe i2c bus downstream from the BMC.
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Havard Skinnemoen <hskinnemoen@google.com>
Message-Id: <20210412194522.664594-5-venture@google.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Moves the search for matching devices on an i2c bus into a separate
method. This allows for an object that owns an I2CBus can avoid
duplicating this method.
Tested: A BMC firmware was booted to userspace and i2c devices were
detected.
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Message-Id: <20210412194522.664594-4-venture@google.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
At the start of an i2c transaction, the i2c bus searches its list of
children to identify which devices correspond to the address (or
broadcast). Now the I2CSlave device has a method "match" that
encapsulates the lookup behavior. This allows the behavior to be changed
to support devices, such as i2c muxes.
Tested: A BMC firmware was booted to userspace and i2c devices were
detected.
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Message-Id: <20210412194522.664594-3-venture@google.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
To enable passing the current_devs field as a parameter, we need to use
a named struct type.
Tested: BMC firmware with i2c devices booted to userspace.
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210412194522.664594-2-venture@google.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
This patch implements the FIFO mode of the SMBus module. In FIFO, the
user transmits or receives at most 16 bytes at a time. The FIFO mode
allows the module to transmit large amount of data faster than single
byte mode.
Since we only added the device in a patch that is only a few commits
away in the same patch set. We do not increase the VMstate version
number in this special case.
Reviewed-by: Doug Evans<dje@google.com>
Reviewed-by: Tyrong Ting<kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Message-id: 20210210220426.3577804-6-wuhaotsh@google.com
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This commit implements the single-byte mode of the SMBus.
Each Nuvoton SoC has 16 System Management Bus (SMBus). These buses
compliant with SMBus and I2C protocol.
This patch implements the single-byte mode of the SMBus. In this mode,
the user sends or receives a byte each time. The SMBus device transmits
it to the underlying i2c device and sends an interrupt back to the QEMU
guest.
Reviewed-by: Doug Evans<dje@google.com>
Reviewed-by: Tyrong Ting<kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Message-id: 20210210220426.3577804-2-wuhaotsh@google.com
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
One of the goals of having less boilerplate on QOM declarations
is to avoid human error. Requiring an extra argument that is
never used is an opportunity for mistakes.
Remove the unused argument from OBJECT_DECLARE_TYPE and
OBJECT_DECLARE_SIMPLE_TYPE.
Coccinelle patch used to convert all users of the macros:
@@
declarer name OBJECT_DECLARE_TYPE;
identifier InstanceType, ClassType, lowercase, UPPERCASE;
@@
OBJECT_DECLARE_TYPE(InstanceType, ClassType,
- lowercase,
UPPERCASE);
@@
declarer name OBJECT_DECLARE_SIMPLE_TYPE;
identifier InstanceType, lowercase, UPPERCASE;
@@
OBJECT_DECLARE_SIMPLE_TYPE(InstanceType,
- lowercase,
UPPERCASE);
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Paul Durrant <paul@xen.org>
Acked-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20200916182519.415636-4-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Some typedefs and macros are defined after the type check macros.
This makes it difficult to automatically replace their
definitions with OBJECT_DECLARE_TYPE.
Patch generated using:
$ ./scripts/codeconverter/converter.py -i \
--pattern=QOMStructTypedefSplit $(git grep -l '' -- '*.[ch]')
which will split "typdef struct { ... } TypedefName"
declarations.
Followed by:
$ ./scripts/codeconverter/converter.py -i --pattern=MoveSymbols \
$(git grep -l '' -- '*.[ch]')
which will:
- move the typedefs and #defines above the type check macros
- add missing #include "qom/object.h" lines if necessary
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-9-ehabkost@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-10-ehabkost@redhat.com>
Message-Id: <20200831210740.126168-11-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
In commit d88c42ff2c we added new prototype but neglected to
add their documentation. Fix that.
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200705224154.16917-6-f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
We use "create_simple" names for functions that allocate, initialize,
configure and realize device objects: pci_create_simple(),
isa_create_simple(), usb_create_simple(). For consistency, rename
i2c_create_slave() as i2c_slave_create_simple(). Since we have
to update all the callers, also let it return a I2CSlave object.
Suggested-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200705224154.16917-5-f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The other i2c functions are called i2c_slave_FOO(). Rename as
i2c_slave_realize_and_unref() to be consistent.
Suggested-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200705224154.16917-4-f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
We use "new" names for functions that allocate and initialize
device objects: pci_new(), isa_new(), usb_new().
Let's call this one i2c_slave_new(). Since we have to update
all the callers, also let it return a I2CSlave object.
Suggested-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200705224154.16917-3-f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
All the callers of aspeed_i2c_get_bus() have a AspeedI2CState and
cast it to a DeviceState with DEVICE(), then aspeed_i2c_get_bus()
cast the DeviceState to an AspeedI2CState with ASPEED_I2C()...
Simplify aspeed_i2c_get_bus() callers by using AspeedI2CState
argument.
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200705224154.16917-2-f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Extract i2c_try_create_slave() and i2c_realize_and_unref()
from i2c_create_slave().
We can now set properties on a I2CSlave before it is realized.
This is in line with the recent qdev/QOM changes merged
in commit 6675a653d2.
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Tested-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20200623072723.6324-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
'ARM SBCon two-wire serial bus interface' is the official
name describing the pair of registers used to bitbanging
I2C in the Versatile boards.
Make the private VersatileI2CState structure as public
ArmSbconI2CState.
Add the TYPE_ARM_SBCON_I2C, alias to our current
TYPE_VERSATILE_I2C model.
Rename the memory region description as 'arm_sbcon_i2c'.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200617072539.32686-5-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
On the NRF51 series, all peripherals have a fixed I/O size
of 4KiB. Define NRF51_PERIPHERAL_SIZE and use it.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200504072822.18799-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Error ** argument must be NULL, &error_abort, &error_fatal, or a
pointer to a variable containing NULL. Passing an argument of the
latter kind twice without clearing it in between is wrong: if the
first call sets an error, it no longer points to NULL for the second
call.
spd_data_generate() can pass @errp to error_setg() more than once when
it adjusts both memory size and type. Harmless, because no caller
passes anything that needs adjusting. Until the previous commit,
sam460ex passed types that needed adjusting, but not sizes.
spd_data_generate()'s contract is rather awkward:
If everything's fine, return non-null and don't set an error.
Else, if memory size or type need adjusting, return non-null and
set an error describing the adjustment.
Else, return null and set an error reporting why no data can be
generated.
Its callers treat the error as a warning even when null is returned.
They don't create the "smbus-eeprom" device then. Suspicious.
Since the previous commit, only "everything's fine" can actually
happen. Drop the unused code and simplify the callers. This gets rid
of the error API violation.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20200422134815.1584-3-armbru@redhat.com>
The I2C controller of the Aspeed AST2500 and AST2600 SoCs supports DMA
transfers to and from DRAM.
A pair of registers defines the buffer address and the length of the
DMA transfer. The address should be aligned on 4 bytes and the maximum
length should not exceed 4K. The receive or transmit DMA transfer can
then be initiated with specific bits in the Command/Status register of
the controller.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-5-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SRAM must be enabled before using the Buffer Pool mode or the DMA
mode. This is not required on other SoCs.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-3-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Aspeed I2C controller can operate in different transfer modes :
- Byte Buffer mode, using a dedicated register to transfer a
byte. This is what the model supports today.
- Pool Buffer mode, using an internal SRAM to transfer multiple
bytes in the same command sequence.
Each SoC has different SRAM characteristics. On the AST2400, 2048
bytes of SRAM are available at offset 0x800 of the controller AHB
window. The pool buffer can be configured from 1 to 256 bytes per bus.
On the AST2500, the SRAM is at offset 0x200 and the pool buffer is of
16 bytes per bus.
On the AST2600, the SRAM is at offset 0xC00 and the pool buffer is of
32 bytes per bus. It can be splitted in two for TX and RX but the
current model does not add support for it as it it unused by known
drivers.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-2-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The I2C controller of the AST2400 and AST2500 SoCs have one IRQ shared
by all I2C busses. The AST2600 SoC I2C controller has one IRQ per bus
and 16 busses.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190925143248.10000-17-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It prepares ground for register differences between SoCs.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190925143248.10000-16-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In my "build everything" tree, changing hw/qdev-properties.h triggers
a recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Many places including hw/qdev-properties.h (directly or via hw/qdev.h)
actually need only hw/qdev-core.h. Include hw/qdev-core.h there
instead.
hw/qdev.h is actually pointless: all it does is include hw/qdev-core.h
and hw/qdev-properties.h, which in turn includes hw/qdev-core.h.
Replace the remaining uses of hw/qdev.h by hw/qdev-properties.h.
While there, delete a few superfluous inclusions of hw/qdev-core.h.
Touching hw/qdev-properties.h now recompiles some 1200 objects.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Daniel P. Berrangé" <berrange@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190812052359.30071-22-armbru@redhat.com>
