S390PCIBusDevice is typedef'ed earlier in the file, before the hunks
that this patch modifies. The double typedef causes old versions of
GCC to complain.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1485523252-88288-1-git-send-email-pbonzini@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Current code seems to assume ring size is
always decreased but this is not required by spec:
what spec says is just that size can not exceed
the maximum. Fix it up.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <1484256243-1982-1-git-send-email-mst@redhat.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Currently there're two functions, s390_pci_setup_msix() and
s390_pci_msix_init(), for msix initialization, and being called once
for each zpci device plugging. Let's integrate them.
Moreover msix is mandatory in s390 architecture. So we ensure the pci
device being plugged supports msix. For vfio (which is the only tested
setup so far), nothing changes.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
The PCI bus number is usually set by the host during the enumeration.
In the s390 architecture we neither get a Device Tree nor have an
enumeration understanding bridge devices.
Let's fake the enumeration on reset and set the PCI_PRIMARY_BUS,
PCI_SECONDARY_BUS and PCI_SUBORDINATE_BUS config entries for the
bridges.
Let's add the configuration of these three config entries on bridge hot
plug.
The bus number is calculated based on a new entry, bus_num of the
S390pciState device.
This commit is inspired by what spapr pci does.
Signed-off-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
After PCI multibus is supported, more than 32 PCI devices could be
plugged. The current implementation of s390_pci_find_dev_by_fh()
appears low performance if there's a huge number of PCI devices
plugged. Therefore we introduce a hashtable using idx as key to store
zpci device's pointer on account of translating fh to idx very easily.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
When the hotplug handler detects a PCI bridge, the secondary bus has
been initialized by the core PCI code. We give the secondary bus the
bridge name and associate to it the IOMMU handling and
hotplug/hotunplug callbacks.
Signed-off-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
A function may recursively call device search functions or may call
serveral different device search function. Passing the S390pciState to
search functions as an argument instead of looking up it inside the
search functions lowers the number of calling s390_get_phb().
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
In order to support a greater number of devices we use a QTAILQ
list of devices instead of a limited array.
This leads us to change:
- every lookup function s390_pci_find_xxx() for QTAILQ
- the FH_MASK_INDEX to index up to 65536 devices
Signed-off-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
When initializing a PCI device, an address space is required during PCI
core initialization and before the call to the embedding object hotplug
callback. To provide this AS, we allocate a S390PCIIOMMU object
containing this AS. Initialization of S390PCIIOMMU object is done
before the PCI device is completely created. So that we cannot
associate the IOMMU with the device at the moment. To track the IOMMU
object, we use g_hash functions with the PCI device's bus address as a
key to provide an array of pointers indexed by the PCI device's devfn
to the allocated IOMMU.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Currently S390PCIIOMMU is a normal struct. Let's make it inherit Object
in order to take advantage of QOM. In addition, we move some stuff
related to IOMMU from S390PCIBusDevice to S390PCIIOMMU.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Acked-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
We chain our compat handler via the CCW_COMPAT macros and via the
class_init function. (e.g. ccw_machine_2_7_class_options calls
ccw_machine_2_8_class_options). As all class_init functions in that
chain call SET_MACHINE_COMPAT for their compat settings, and
SET_MACHINE_COMPAT will append there is no need to do that again.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Move the generic cpu_synchronize_ functions to the common hw_accel.h header,
in order to prepare for the addition of a second hardware accelerator.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Message-Id: <f5c3cffe8d520011df1c2e5437bb814989b48332.1484045952.git.vpalatin@chromium.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Because guest mask notifier cannot be used in vhost-user mode, a boolean
flag "use_guest_notifier_mask" was added in commit 5669655aaf to disable
the use of guest mask notifier under virtio-pci. However this flag wasn't
checked in other virtio devices, such as virtio-mmio. In our tests, it
caused assertion error under "vhost-user + virtio-mmio". This patch
addresses this problem by adding a check before guest_notifier_mask is
called.
Signed-off-by: Wei Huang <wei@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Legacy features are those that transitional devices only
expose on the legacy interface.
Allow different ones per device class.
Cc: qemu-stable@nongnu.org # dependency for the next patch
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
The instructions PCI STORE, PCI LOAD and PCI STORE BLOCK
use calls to memory_region_dispatch_write() and
memory_region_dispatch_read() but do not test the return value.
Furthermore, the instruction PCI STORE BLOCK sets up a PGM_ADDRESSING
exception when the operand 3 is not within the designated PCI address
space instead of a PGM_OPERAND exception.
Let's setup a PGM_OPERAND exception in all of these failure cases.
Signed-off-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Let's use the generic interface to inject adapter interrupts.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
This will be used to forbid iothread configuration when the
proxy does not allow using ioeventfd. To simplify the implementation,
change the direction of the ioeventfd_disabled callback too.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This simplifies the code and removes the ioeventfd_started
and ioeventfd_set_started callback. The only difference is
in how virtio-ccw handles an error---it doesn't disable
ioeventfd forever anymore. It was the only backend to do
so, and if desired this behavior should be implemented in
virtio-bus.c.
Instead of ioeventfd_started, the ioeventfd_assign callback now
determines whether the virtio bus supports host notifiers.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This simplifies the code and removes the ioeventfd_set_disabled
callback.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Avoid "tricking" virtio-blk-dataplane into thinking that ioeventfd will be
available when it is not. This bug has always been there, but it will break
TCG+ioeventfd=on once the dataplane code will be always used when ioeventfd=on.
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Coverity points out that the comparison "fid <= ZPCI_MAX_FID"
in s390_pci_generate_fid() is always true (because fid
is 32 bits and ZPCI_MAX_FID is 0xffffffff). This isn't a
bug because the real loop termination condition is
expressed later via an "if (...) break;" inside the loop,
but it is a bit odd. Rephrase the loop to avoid the
unnecessary duplicate-but-never-true conditional.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
According to the PoP, subchannels are only considered operational if
they are enabled _and_ the device number is valid. With the current
checks being enabled _or_ having a valid device number was
sufficient. This caused qemu to allow IO on subchannels that were not
enabled.
Fix the checks to require both bits to be set.
Signed-off-by: Sascha Silbe <silbe@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Now that each S390 PCI device uses an IO region as MSIX region. The
code in s390_translate_iommu() will never be triggered. Let's remove
it.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
For efficiency we now assign one msix io region for each pci device
and provide it with the pointer to the zPCI device as opaque
parameter. In addition, we remove msix address space and add msix io
region as a subregion to the root memory region of pci device.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Pull mr variable declarations at the top of the functions instead of
mixing them up with the code. This is in preparation for followup
patches.
Signed-off-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
We have everything needed for virtio-ccw revision 2 wired up now.
Bump the maximum supported revision reported on a device basis to
the guest so they can make use of it.
Signed-off-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
This patch adds the response to the READ_STATUS CCW command.
Signed-off-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
cpu model was merged with 2.8, it is wrong to abuse ri_allowed which
was enabled with 2.7.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Currently, devices are plugged before features are negotiated.
If the backend doesn't support VIRTIO_F_VERSION_1, the transport
needs to rewind some settings.
This is the case for CCW, for which a post_plugged callback had
been introduced, where max_rev field is just updated if
VIRTIO_F_VERSION_1 is not supported by the backend.
For PCI, implementing post_plugged would be much more
complicated, so it needs to know whether the backend supports
VIRTIO_F_VERSION_1 at plug time.
Currently, nothing is done for PCI. Modern capabilities get
exposed to the guest even if VIRTIO_F_VERSION_1 is not supported
by the backend, which confuses the guest.
This patch replaces existing post_plugged solution with an
approach that fits with both transports.
Features negotiation is performed before ->device_plugged() call.
A pre_plugged callback is introduced so that the transports can
set their supported features.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: qemu-stable@nongnu.org
Tested-by: Cornelia Huck <cornelia.huck@de.ibm.com> [ccw]
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Maxime Coquelin <maxime.coquelin@redhat.com>
This patch is the result of coccinelle script
scripts/coccinelle/typecast.cocci
CC: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Unused function declarations were found using a simple gcc plugin and
manually verified by grepping the sources.
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Implement the new virtio sockets device for host<->guest communication
using the Sockets API. Most of the work is done in a vhost kernel
driver so that virtio-vsock can hook into the AF_VSOCK address family.
The QEMU vhost-vsock device handles configuration and live migration
while the rx/tx happens in the vhost_vsock.ko Linux kernel driver.
The vsock device must be given a CID (host-wide unique address):
# qemu -device vhost-vsock-pci,id=vhost-vsock-pci0,guest-cid=3 ...
For more information see:
http://qemu-project.org/Features/VirtioVsock
[Endianness fixes and virtio-ccw support by Claudio Imbrenda
<imbrenda@linux.vnet.ibm.com>]
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
[mst: rebase to master]
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
To be able to query the correct host model for the "none" machine,
let's allow runtime-instrumentation for that machine.
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Message-Id: <20160905085244.99980-21-dahi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
The mha is provided in the CPU model, so get any CPU and extract the value.
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Message-Id: <20160905085244.99980-18-dahi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
If we have a lowest ibc, we can indicate the ibc to the guest.
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Message-Id: <20160905085244.99980-17-dahi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
We have three different blocks in the SCLP read-SCP information response
that indicate sclp features. Let's prepare propagation.
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Message-Id: <20160905085244.99980-16-dahi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Let's factor out the common code of "read cpu info" and "read scp
info". This will make the introduction of new cpu entry fields easier.
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Message-Id: <20160905085244.99980-14-dahi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
This patch introduces two CPU models, "host" and "qemu".
"qemu" is used as default when running under TCG. "host" is used
as default when running under KVM. "host" cannot be used without KVM.
"host" is not migration-safe. They both inherit from the base s390x CPU,
which is turned into an abstract class.
This patch also changes CPU creation to take care of the passed CPU string
and reuses common code parse_features() function for that purpose. Unknown
CPU definitions are now reported. The "-cpu ?" and "query-cpu-definition"
commands are changed to list all CPU subclasses automatically, including
migration-safety and whether static.
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Message-Id: <20160905085244.99980-3-dahi@linux.vnet.ibm.com>
[CH: fix up self-assignments in s390_cpu_list, as spotted by clang]
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
The cssid 255 is reserved but still valid from an architectural
point of view. However, feeding a bogus schid of 0xffffffff into
the virtio hypercall will lead to a crash:
Stack trace of thread 138363:
#0 0x00000000100d168c css_find_subch (qemu-system-s390x)
#1 0x00000000100d3290 virtio_ccw_hcall_notify
#2 0x00000000100cbf60 s390_virtio_hypercall
#3 0x000000001010ff7a handle_hypercall
#4 0x0000000010079ed4 kvm_cpu_exec (qemu-system-s390x)
#5 0x00000000100609b4 qemu_kvm_cpu_thread_fn
#6 0x000003ff8b887bb4 start_thread (libpthread.so.0)
#7 0x000003ff8b78df0a thread_start (libc.so.6)
This is because the css array was only allocated for 0..254
instead of 0..255.
Let's fix this by bumping MAX_CSSID to 255 and fencing off the
reserved cssid of 255 during css image allocation.
Reported-by: Christian Borntraeger <borntraeger@de.ibm.com>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: qemu-stable@nongnu.org
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
With the current code a simple sclp command takes about 13000 ns
The biggest part seems to be the resolver of the object model. By
caching the sclp device the time for an sclp command goes down to
2500ns. Talking about real life scenarios, this change doubles
the speed of the sclp console when sending single bytes outputs
to /dev/console.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
If one pci device is plugged successfully, there must be a zpci device
existing. This means that during hot-unplugging a pci device, its
corresponding zpci device must be found. Therefore we use an assert to
replace current code.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
In the case that zpci is automatically created, we did not return
immediately on failure, which would lead to NULL pointer dereferencing.
Let's fix it.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
We should make sure that it's not NULL firstly.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
We need to implement the get_dev_path method for the css bus, or
else we might end up with two different devices having the same
qdev_path.
This was noticed when adding two scsi_hd controllers: The SCSIBus
code will produce a non-unique dev_path for vmstate usage if the
parent bus does not provide the get_dev_path method.
We simply use the device's bus id, as this is unique and we won't
have any deeper hierarchy from a channel subsystem perspective
anyway.
Note that we need to disable this for older machine versions,
as this changes the migration format.
Reported-by: Marc Hartmayer <mhartmay@linux.vnet.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reviewed-by: Sascha Silbe <silbe@linux.vnet.ibm.com>
Tested-by: Marc Hartmayer <mhartmay@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
It's not obvious from the code flow that sch_handle_start_func() gets
called for rsch. Add some comments explaining this.
Signed-off-by: Sascha Silbe <silbe@linux.vnet.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
The CCW Format (F) flag of the Subchannel-Status Word (SCSW) indicates
the format of the CCWs "associated with an I/O operation", i.e. the
value of CCW-Format Control (F) bit of the Operation-Request Block
(ORB).
Copy the CCW format bit from the ORB to the SCSW so we correctly
indicate the format of the CCWs to the guest.
Signed-off-by: Sascha Silbe <silbe@linux.vnet.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Tracked down with an ugly, brittle and probably buggy Perl script.
Also move includes converted to <...> up so they get included before
ours where that's obviously okay.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Tested-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
The current implementation of hot-unplug handler is abrupt. Any pci
operation will be just rejected if pci device is unconfigured. Thus a
pci device can not be reset or destroyed in a right, smooth and safe
way.
Improve this as follows:
- Notify the guest via a HP_EVENT_DECONFIGURE_REQUEST(0x303) event in
the unplug handler, giving it a chance to deconfigure the device via
sclp and allowing us to continue hot-unplug afterwards.
- Set up a timer that will generate the HP_EVENT_CONFIGURE_TO_STBRES
(0x304) event as before if the guest did not react after an adequate
time.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Present code uses fid as the part of message data of msix for looking
up the specific zpci device. However it limits the usable range of fid,
and the code looking up the zpci device may fail due to truncation of
the fid.
In addition, fh is composed of enabled bit, FH_VIRT and the array index.
So we can use the array index as the identifier to store in msg data.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Firstly the function misses dmaas checking. This patch adds it.
Secondly the function uses s390_pci_find_dev_by_fh() to look up the
zpci device. This may fail if the guest provides a valid and disabled
fh but fh of the associated zpci device is enabled. Thus we use
s390_pci_find_dev_by_idx() instead.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Because of the refactor of s390_pci_find_dev_by_idx(), list_pci()
should be updated. We introduce a new function to get the next
available zpci device. It simplifies the code of looking up zpci
devices.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Acked-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
s390_find_dev_by_idx() only indexes usable zpci devices. It implies
that the index value of each zpci device is dynamic and may change if
a new zpci device is plugged. So we have to use a constant index to
look up the device.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
The code in CLP_SET_PCI_FN case misses some checkings. Let's add
them.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
We need to support hot-plug/hot-unplug for the new zpci devices as
well. This patch enables the present hot-plug/hot-unplug handlers
to support not only generic pci devices but also zpci devices.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
The uid-checking facility guarantees uniqueness of the uid within the
vm and exposes the real uid to the guest when listing pci devices.
Let's always enable it and present it to the guest in the response to
the list pci clp command.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
To support definitions of s390 pci attributes in Qemu cmdline, we have
to make current S390PCIBusDevice struct inherit DeviceState and add
three properties for it. Currently we only support definitions of uid
and fid.
'uid' is optionally defined by users, identifies a zpci device and
must be defined with a 16-bit and non-zero unique value.
'fid' ranges from 0x0 to 0xFFFFFFFF. For fid property, we introduce a
new PropertyInfo by the name of s390_pci_fid_propinfo with our special
setter and getter. As 'fid' is optional, introduce 'fid_defined' to
track whether the user specified a fid.
'target' field is to direct qemu to find the corresponding generic PCI
device. It is equal to the 'id' value of one of generic pci devices.
If the user doesn't specify 'id' parameter for a generic pci device,
its 'id' value will be generated automatically and use this value as
'target' to create an associated zpci device.
If the user did not specify 'uid' or 'fid', values are generated
automatically. 'target' is required.
In addition, if a pci device has no associated zpci device, the code
will generate a zpci device automatically for it.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Currently each zpci device holds its own DMA address space and memory
region. At the same time, all instances of zpci device are stored in
S390pciState. So duirng the initialization of S390pciState, all zpci
devices are created and then all DMA address spaces are created. Thus,
when initializing pci devices, their corresponding DMA address spaces
could be found.
But zpci qdev will be introduced later. Zpci device may be initialized
and plugged afterwards generic pci device. So we should initialize all
DMA address spaces and memory regions before initializing zpci devices.
We introduce a new struct named S390PCIIOMMU. And a new field of
S390pciState, which is an array to store all instances of S390PCIIOMMU,
is added so that qemu pci code could find the corresponding DMA
address space when initializing a generic pci device. And this should
be done before the connection of a zpci device and a generic pci
device is built.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Acked-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
To enable S390PCIBusDevice as qdev, there should be a new bus to
plug and manage all instances of S390PCIBusDevice. Due to this,
S390PCIBus is introduced.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Current code uses some fields combinatorially to indicate the state of
a s390 pci device. This patch introduces device states in order to make
the code more readable and more logical.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Because this function is called very frequently, we should use a more
effective way to find the zpci device. So we use the FH's index to get
the device directly.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Present code uses some macros to structure PCI Function Handle. But
their names don't have a uniform format. Let's use FH_MASK_ as the
unified prefix.
While we're at it, differentiate the SHM bits: use different bits for
vfio and emulated devices.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
We forgot to write the fid; fix that.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Acked-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
There are a number of places where the code needs to get the instance
of S390pciState. It calls object_resolve_path() every time. This
wastes a lot of time and leads to low performance. Thus we add
s390_get_phb() to improve it.
Because we always have a phb, we remove all return checkings in the
callers and add an assert in s390_get_phb() to make sure that phb is
getted successfully.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
In commit d78c19b5cf, vfio code stores
the IOMMU's offset_within_address_space and adjusts the IOVA before
calling vfio_dma_map/vfio_dma_unmap. But s390_translate_iommu already
considers the base address of an IOMMU memory region.
Thus we use pal as the size and 0x0 as the base address to initialize
IOMMU memory subregion.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
The previous patch moved virtual css bridge and bus out from
virtio-ccw, but kept the direct reference of virtio-ccw specific
unplug function inside css-bridge.c.
To make the virtual css bus and bridge useful for non-virtio devices,
this introduces a common unplug function pointer "unplug" to call
specific virtio-ccw unplug parts. Thus, the tight coupling to
virtio-ccw can be removed.
This unplug pointer is a member of CCWDeviceClass, which is introduced
as an abstract device layer called "ccw-device". This layer is between
DeviceState and specific devices which are plugged in virtual css bus,
like virtio-ccw device. The specific unplug handlers should be assigned
to "unplug" during initialization.
Signed-off-by: Jing Liu <liujbjl@linux.vnet.ibm.com>
Reviewed-by: Sascha Silbe <silbe@linux.vnet.ibm.com>
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Reviewed-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Currently, common base layers virtual css bridge and bus are
defined in hw/s390x/virtio-ccw.c(h). In order to support
multiple types of devices in the virtual channel subsystem,
especially non virtio-ccw, refactoring work needs to be done.
This work is just a pure code move without any functional change
except dropping an empty function virtual_css_bridge_init() and
virtio_ccw_busdev_unplug() changing. virtio_ccw_busdev_unplug()
is specific to virtio-ccw but gets referenced from the common
virtual css bridge code. To keep the functional changes to a
minimum we export this function from virtio-ccw.c and continue
to reference it inside virtual_css_bridge_class_init()
(now living in hw/s390x/css-bridge.c). A follow-up patch will
clean this up.
Signed-off-by: Jing Liu <liujbjl@linux.vnet.ibm.com>
Reviewed-by: Sascha Silbe <silbe@linux.vnet.ibm.com>
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Introduce a TYPE_* define (like we already use for a couple of other
QOM types) for the name of the virtual CSS bridge QOM type instead of
sprinkling the same string literal over several source files.
Signed-off-by: Sascha Silbe <silbe@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
A lot of what virtio_ccw_device_realize() does isn't specific to
virtio; it would apply to emulated CCW as well. Factor it out to make
it easier to implement emulated CCW devices later on.
Signed-off-by: Sascha Silbe <silbe@linux.vnet.ibm.com>
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
When migrating from a different QEMU version, the start_address and
bios_start_address may differ. During migration these values are migrated
and overwrite the values that were detected by QEMU itself.
On a reboot, QEMU will reload its own BIOS, but use the migrated start
addresses, which does not work if the values differ.
Fix this by not relying on the migrated values anymore, but still
provide them during migration, so existing QEMUs continue to work.
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Cc: qemu-stable@nongnu.org
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
If bootindex is specified for a device, we need to IPL from
it. Currently it works for ccw devices, but not for SCSI. To be able to
IPL from the specific device, pc-bios needs to know its address.
For this reason we add special QEMU_SCSI IPL type into the IPLB
structure, that contains the scsi device address.
We enhance the ipl block with a currently qemu-only parameter block
that allows us to specify a concrete scsi device.
Signed-off-by: Alexander Yarygin <yarygin@linux.vnet.ibm.com>
Reviewed-by: Eric Farman <farman@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Use the new interface.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Version: GnuPG v1
iQEcBAABAgAGBQJXaFInAAoJEJykq7OBq3PI6VsH/0Sfgbdo1RksYuQwb/y92sCW
EN+lxUZ+OLfgrc8PYgNZwfSM3rsfYhznL0MAXOeEe7Ahabi07w7DhGR8WvwfAOlI
G96FRuvrIPfv5u6U6fwS4CvG3TIHVLxfHKCsTpPUmH8U5CNx/x/tpjNiWN1dj6t+
sXybSjYHfZfiZy2tI9MFIFWCdxnF/pl0QAPhbRqc8Y/RQTDrPKRjLpz+nitN/u96
5TS7KlELyQuP91YMmLceYSmIkHbxW703h+iE2n4hov0uZCP8Jil+2Jsd3ziQSRlL
j6LqexQ2ViBGdDSfiZGYES2VPlsHOCwb4G+IgWBStfZg1ppaXENvcDzPrgrB+L4=
=eUnF
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stefanha/tags/tracing-pull-request' into staging
# gpg: Signature made Mon 20 Jun 2016 21:29:27 BST
# gpg: using RSA key 0x9CA4ABB381AB73C8
# gpg: Good signature from "Stefan Hajnoczi <stefanha@redhat.com>"
# gpg: aka "Stefan Hajnoczi <stefanha@gmail.com>"
# Primary key fingerprint: 8695 A8BF D3F9 7CDA AC35 775A 9CA4 ABB3 81AB 73C8
* remotes/stefanha/tags/tracing-pull-request: (42 commits)
trace: split out trace events for linux-user/ directory
trace: split out trace events for qom/ directory
trace: split out trace events for target-ppc/ directory
trace: split out trace events for target-s390x/ directory
trace: split out trace events for target-sparc/ directory
trace: split out trace events for net/ directory
trace: split out trace events for audio/ directory
trace: split out trace events for ui/ directory
trace: split out trace events for hw/alpha/ directory
trace: split out trace events for hw/arm/ directory
trace: split out trace events for hw/acpi/ directory
trace: split out trace events for hw/vfio/ directory
trace: split out trace events for hw/s390x/ directory
trace: split out trace events for hw/pci/ directory
trace: split out trace events for hw/ppc/ directory
trace: split out trace events for hw/9pfs/ directory
trace: split out trace events for hw/i386/ directory
trace: split out trace events for hw/isa/ directory
trace: split out trace events for hw/sd/ directory
trace: split out trace events for hw/sparc/ directory
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move all trace-events for files in the hw/s390x/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Message-id: 1466066426-16657-29-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This patch simplifies code that uses a local_err variable just to
immediately use it for an error_propagate() call.
Coccinelle patch used to perform the changes added to
scripts/coccinelle/remove_local_err.cocci.
Reviewed-by: Eric Blake <eblake@redhat.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <1465855078-19435-3-git-send-email-ehabkost@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[Blank line in s390-virtio-ccw.c restored]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
error_propagate() already ignores local_err==NULL, so there's no
need to check it before calling.
Coccinelle patch used to perform the changes added to
scripts/coccinelle/error_propagate_null.cocci.
Reviewed-by: Eric Blake <eblake@redhat.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <1465855078-19435-2-git-send-email-ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
The sclp scp read info call fills in a buffer with information about the
system. With more than 248 CPUs we overflow the 4k buffer of the SCCB,
leading to random data corruption. Basically ALL guest operating systems
call scp read info, so let's limit the machines to 248 CPUs to make it
obvious that >=249 does not work.
As KVM also limits itself to 248 and TCG on s390 does not support
SMP, this should cause no regression for any user as no VMs with more
than 248 VCPUs were ever possible.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Reviewed-by: Boris Fiuczynski <fiuczy@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
This allows to trace changes in the summary and queue indicators
for the non-irqfd case. For irqfd, kernel traces are needed instead.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Let's introduce a CssDevId to handle device ids of the xx.x.xxxx
type used for channel devices. This has some benefits:
- We can use them in virtio-ccw and split the validity checks for
a channel device id in general from the constraint checking
within the virtio-ccw scope.
- We can reuse the device id type for future non-virtio channel
devices.
While we're at it, improve the validity checks and disallow e.g.
trailing characters.
Suggested-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Acked-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
According to the Principles of Operation (more precisely the subsection
'Channel-Report Word'), a subchannel put into the installed parameters
initialized state is in the same state as after an I/O system reset (just
parameters possibly changed). This implies that any I/O interrupts for that
subchannel are no longer pending (as I/O system resets clear I/O
interrupts). Therefore, we need an interface to clear pending I/O
interrupts. Make css_generate_sch_crws clear the pending IO interrupts for
the subchannel.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
The s390 skeys monitor command needs to write out a plain text
file. Currently it is using the QEMUFile class for this, but
work is ongoing to refactor QEMUFile and eliminate much code
related to it. The only feature qemu_fopen() gives over fopen()
is support for QEMU FD passing, but this can be achieved with
qemu_open() + fdopen() too. Switching to regular stdio FILE
APIs avoids the need to sprintf via an intermedia buffer which
slightly simplifies the code.
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <1461751518-12128-2-git-send-email-berrange@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Switch to adding compat properties incrementaly instead of
completly overwriting compat_props per machine type.
That removes data duplication which we have due to nested
[PC|SPAPR]_COMPAT_* macros.
It also allows to set default device properties from
default foo_machine_options() hook, which will be used
in following patch for putting VMGENID device as
a function if ISA bridge on pc/q35 machines.
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
[ehabkost: Fixed CCW_COMPAT_* and PC_COMPAT_0_* defines]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Move cpu_inject_* to the only C file where they are used.
Move ioinst.h declarations that need S390CPU to cpu.h, to make
ioinst.h independent of cpu.h.
Move channel declarations that only need SubchDev from cpu.h
to css.h, to make more channel users independent of cpu.h.
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The configure/deconfigure sclp commands need a SCCB with a length of
at least 16. Indicate in the response code if this is not fulfilled.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Enhance error handling for mpcifc_service_call() to propagate errors
to guest by setting status codes or triggering program interrupts.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
When deconfiguring a s390 pci device, we should deconfigure the
corresponding IOMMU memory region and the IRQs for the device.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
We introduce iommu_enabled field for S390PCIBusDevice struct to
track whether the iommu has been enabled for the device. This allows
us to stop temporarily changing ->configured while en/disabling the
iommu and to do conditional cleanup later.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
