RTL8139 ethernet controller in C+ mode supports multiple
descriptor rings, each with maximum of 64 descriptors. While
processing transmit descriptor ring in 'rtl8139_cplus_transmit',
it does not limit the descriptor count and runs forever. Add
check to avoid it.
Reported-by: Andrew Henderson <hendersa@icculus.org>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
In Vmxnet3 device emulator while processing transmit(tx) queue,
when it reaches end of packet, it calls vmxnet3_complete_packet.
In that local 'txcq_descr' object is not initialised, which could
leak host memory bytes a guest.
Reported-by: Li Qiang <liqiang6-s@360.cn>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Reviewed-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The e1000e emulation zeroes out any used rx descriptor and then writes a
completely newly constructed value there. By doing this, it doesn't only
update the write-back area of the descriptors (as it's supposed to do),
but it also clears the buffer address, which real hardware doesn't do.
The spec explicitly mentions in chapter 7.1.8 that it is valid for a
driver to reuse a descriptor and only update the status field while
doing so, i.e. reusing the old buffer address:
If software statically allocates buffers, and uses memory read to
check for completed descriptors, it simply has to zero the status
byte in the descriptor to make it ready for reuse by hardware.
This patch fixes the behaviour to leave the buffer address in
descriptors unchanged even after the descriptor has been used.
Signed-off-by: Kevin Wolf <mail@kevin-wolf.de>
Reviewed-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Rocker network switch emulator has test registers to help debug
DMA operations. While testing host DMA access, a buffer address
is written to register 'TEST_DMA_ADDR' and its size is written to
register 'TEST_DMA_SIZE'. When performing TEST_DMA_CTRL_INVERT
test, if DMA buffer size was greater than 'INT_MAX', it leads to
an invalid buffer access. Limit the DMA buffer size to avoid it.
Reported-by: Huawei PSIRT <psirt@huawei.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The exit dispatch of eepro100 network card device doesn't free
the 's->vmstate' field which was allocated in device realize thus
leading a host memory leak. This patch avoid this.
Signed-off-by: Li Qiang <liqiang6-s@360.cn>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Fix indentations and source format at few places. Add braces
around 'if' and 'while' statements.
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The AMD PC-Net II emulator has set of control and status(CSR)
registers. Of these, CSR76 and CSR78 hold receive and transmit
descriptor ring length respectively. This ring length could range
from 1 to 65535. Setting ring length to zero leads to an infinite
loop in pcnet_rdra_addr() or pcnet_transmit(). Add check to avoid it.
Reported-by: Li Qiang <liqiang6-s@360.cn>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Separate all ccr bits. Continue to batch updates via cc_op.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Fix gen_logic_cc() to really extend the size of the result.
Fix gen_get_ccr(): update cc_op as it is used by the helper.
Factorize flags computing and src/ccr cleanup
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
target-m68k: sr/ccr cleanup
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The CF docs certainly doesnt suggest this is true.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Read a 8, 16 or 32bit immediat constant.
An immediate constant is stored in the instruction opcode and
can be in one or two extension words.
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Scaled index is not supported by 68000, 68008, and 68010.
EA = (bd + PC) + Xn.SIZE*SCALE + od
Ignore it:
M68000 FAMILY PROGRAMMER’S REFERENCE MANUAL
2.4 BRIEF EXTENSION WORD FORMAT COMPATIBILITY
"If the MC68000 were to execute an instruction that
encoded a scaling factor, the scaling factor would be
ignored and would not access the desired memory address.
The earlier microprocessors do not recognize the brief
extension word formats implemented by newer processors.
Although they can detect illegal instructions, they do not
decode invalid encodings of the brief extension word formats
as exceptions."
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Richard Henderson <rth@twiddle.net>
The qdict_flatten() method will take a dict whose elements are
further nested dicts/lists and flatten them by concatenating
keys.
The qdict_crumple() method aims to do the reverse, taking a flat
qdict, and turning it into a set of nested dicts/lists. It will
apply nesting based on the key name, with a '.' indicating a
new level in the hierarchy. If the keys in the nested structure
are all numeric, it will create a list, otherwise it will create
a dict.
If the keys are a mixture of numeric and non-numeric, or the
numeric keys are not in strictly ascending order, an error will
be reported.
As an example, a flat dict containing
{
'foo.0.bar': 'one',
'foo.0.wizz': '1',
'foo.1.bar': 'two',
'foo.1.wizz': '2'
}
will get turned into a dict with one element 'foo' whose
value is a list. The list elements will each in turn be
dicts.
{
'foo': [
{ 'bar': 'one', 'wizz': '1' },
{ 'bar': 'two', 'wizz': '2' }
],
}
If the key is intended to contain a literal '.', then it must
be escaped as '..'. ie a flat dict
{
'foo..bar': 'wizz',
'bar.foo..bar': 'eek',
'bar.hello': 'world'
}
Will end up as
{
'foo.bar': 'wizz',
'bar': {
'foo.bar': 'eek',
'hello': 'world'
}
}
The intent of this function is that it allows a set of QemuOpts
to be turned into a nested data structure that mirrors the nesting
used when the same object is defined over QMP.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1475246744-29302-3-git-send-email-berrange@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[Parameter recursive dropped along with its tests; whitespace style
touched up]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
The input_visitor_test_add() method was accepting an instance
of 'TestInputVisitorData' and passing it as the 'user_data'
parameter to test functions. The main 'TestInputVisitorData'
instance that was actually used, was meanwhile being allocated
automatically by the test framework fixture setup.
The 'user_data' parameter is going to be needed for tests
added in later patches, so getting rid of the current mistaken
usage now allows this.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1475246744-29302-7-git-send-email-berrange@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
The QmpOutputVisitor has no direct dependency on QMP. It is
valid to use it anywhere that one wants a QObject. Rename it
to better reflect its functionality as a generic QAPI
to QObject converter.
The commit before previous renamed the files, this one renames C
identifiers.
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1475246744-29302-6-git-send-email-berrange@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[Split into file rename and identifier rename]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
The QmpInputVisitor has no direct dependency on QMP. It is
valid to use it anywhere that one has a QObject. Rename it
to better reflect its functionality as a generic QObject
to QAPI converter.
The previous commit renamed the files, this one renames C identifiers.
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1475246744-29302-5-git-send-email-berrange@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[Straightforwardly rebased, split into file and identifier rename]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
The QMP visitors have no direct dependency on QMP. It is
valid to use them anywhere that one has a QObject. Rename them
to better reflect their functionality as a generic QObject
to QAPI converter.
This is the first of three parts: rename the files. The next two
parts will rename C identifiers. The split is necessary to make git
rename detection work.
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[Split into file and identifier rename, two comments touched up]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Allow tracing of the operation of visitors
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1475246744-29302-4-git-send-email-berrange@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[visit_type_uint8() & friends rearranged slightly for clarity]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Commit de63ab6 accidentally undid part of commit a43edcf,
because the two patches were written in parallel, and the
blank line was not noticed as a casualty of merge conflicts.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1476739794-19536-1-git-send-email-eblake@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Commit ea3af47 accidentally dropped check-qdict from the list of unit
tests. Put it back.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-id: 1477386565-26225-1-git-send-email-armbru@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
x2APIC support to APIC code, cpu_exec_init() refactor on all
architectures, and other x86 changes.
-----BEGIN PGP SIGNATURE-----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=T2kg
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/ehabkost/tags/x86-pull-request' into staging
x86 and CPU queue, 2016-10-24
x2APIC support to APIC code, cpu_exec_init() refactor on all
architectures, and other x86 changes.
# gpg: Signature made Mon 24 Oct 2016 20:51:14 BST
# gpg: using RSA key 0x2807936F984DC5A6
# gpg: Good signature from "Eduardo Habkost <ehabkost@redhat.com>"
# Primary key fingerprint: 5A32 2FD5 ABC4 D3DB ACCF D1AA 2807 936F 984D C5A6
* remotes/ehabkost/tags/x86-pull-request:
exec: call cpu_exec_exit() from a CPU unrealize common function
exec: move cpu_exec_init() calls to realize functions
exec: split cpu_exec_init()
pc: q35: Bump max_cpus to 288
pc: Require IRQ remapping and EIM if there could be x2APIC CPUs
pc: Add 'etc/boot-cpus' fw_cfg file for machine with more than 255 CPUs
Increase MAX_CPUMASK_BITS from 255 to 288
pc: Clarify FW_CFG_MAX_CPUS usage comment
pc: kvm_apic: Pass APIC ID depending on xAPIC/x2APIC mode
pc: apic_common: Reset APIC ID to initial ID when switching into x2APIC mode
pc: apic_common: Restore APIC ID to initial ID on reset
pc: apic_common: Extend APIC ID property to 32bit
pc: Leave max apic_id_limit only in legacy cpu hotplug code
acpi: cphp: Force switch to modern cpu hotplug if APIC ID > 254
pc: acpi: x2APIC support for SRAT table
pc: acpi: x2APIC support for MADT table and _MAT method
Conflicts:
target-arm/cpu.c
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
As cpu_exec_exit() mirrors the cpu_exec_realizefn(),
rename it as cpu_exec_unrealizefn().
Create and register a cpu_common_unrealizefn() function for
the CPU device class and call cpu_exec_unrealizefn() from
this function.
Remove cpu_exec_exit() from cpu_common_finalize()
(which mirrors init, not realize), and as x86_cpu_unrealizefn()
and ppc_cpu_unrealizefn() overwrite the device class unrealize function,
add a call to a parent_unrealize pointer.
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Modify all CPUs to call it from XXX_cpu_realizefn() function.
Remove all the cannot_destroy_with_object_finalize_yet as
unsafe references have been moved to cpu_exec_realizefn().
(tested with QOM command provided by commit 4c315c27)
for arm:
Setting of cpu->mp_affinity is moved from arm_cpu_initfn()
to arm_cpu_realizefn() as setting of cpu_index is now done
in cpu_exec_realizefn(). To avoid to overwrite an user defined
value, we set it to an invalid value by default, and update
it in realize function only if the value is still invalid.
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Put in cpu_exec_initfn() what initializes the CPU,
and leave in cpu_exec_init() what adds it to the environment.
As cpu_exec_initfn() is called by all XX_cpu_initfn(), call it
directly in cpu_common_initfn().
cpu_exec_init() is now a realize function, it will be renamed
to cpu_exec_realizefn() and moved to the XX_cpu_realizefn()
function in a following patch.
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Along with it for machine versions 2.7 and older keep
it at 255.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
It would prevent starting guest with incorrect configs
where interrupts couldn't be delivered to CPUs with
APIC IDs > 255.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Currently firmware uses 1 byte at 0x5F offset in RTC CMOS
to get number of CPUs present at boot. However 1 byte is
not enough to handle more than 255 CPUs. So add a new
fw_cfg file that would allow QEMU to tell it.
For compat reasons add file only for machine types that
support more than 255 CPUs.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
so that it would be possible to increase maxcpus limit
for x86 target. Keep spapr/virt_arm at limit they used
to have 255.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
