Recent PowerPC kernel end up in kernel panic during boot in -nographic
mode. In this mode the second serial port is used as the udbg console,
and thus a few characters are sent on this port. This activates the
tx interrupt flag, and later choke the Linux kernel, as it was not
expecting such a flag to be set.
The problem here comes from the fact that contrary to most devices the
interrupt flags are only set if the interrupt is enabled. Quoting the
datasheet: "If the corresponding IE bit is not set, the IP for that
source of interrupt will never be set."
This patch fixes that by enabling the interrupt flag only when the
corresponding interrupt is enabled.
Cc: Blue Swirl <blauwirbel@gmail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
As noted by Markus Armbruster pxa2xx_gpio vmstate version bumped
because of a change in the or .ilevel / .olevel arrays are saved,
for convenience.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Andrzej Zaborowski <andrew.zaborowski@intel.com>
Switch sl-nand emulation to use qdev and vmstate. Also drop ecc_get/_put
functions as sl-nand was the only user of that code.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Andrzej Zaborowski <andrew.zaborowski@intel.com>
Convert SharpSL scoop device to qdev, remove lots of supporting code, as
lot of init and gpio related things can now be done automagically.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Andrzej Zaborowski <andrew.zaborowski@intel.com>
This patch fixes typo in pcibus_get_dev_path().
Without this patch, the result of pcibus_get_dev_path() isn't unique.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
PCI_BRIDGE_CTL_DISCARD_STATUS (bit 10 in bridge control register)
is W1C so we should not make it writeable, otherwise the assert(!(wmask
& w1cmask)) in pci_default_write_config() is hit
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reported-by: Isaku Yamahata <yamahata@valinux.co.jp>
Tested-by: Isaku Yamahata <yamahata@valinux.co.jp>
Fix the register and part of register we get the scalar from in
the various "multiply vector by scalar" ops (VMUL by scalar
and friends).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This patch fixes corner-case saturations, when the target range is
zero. It merely removes the guard against (sh == 0), and makes:
__ssat(0x87654321, 1) return 0xffffffff and set the saturation flag
__usat(0x87654321, 0) return 0 and set the saturation flag
Signed-off-by: Christophe Lyon <christophe.lyon@st.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Update the PTEH register to contain the VPN at which an MMU
exception occured as specified by the SH4 reference.
Signed-off-by: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Request reasonable buffer sizes from pulseaudio. Without this
pa_simple_write() can block quite long and lead to dropouts,
especially with guests which use small audio ring buffers.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: malc <av1474@comtv.ru>
Limit the size of data pieces processed by the pulseaudio worker
threads. Never ever process more than 1/4 of the buffer at once.
Background: The buffer area currently processed by the pulseaudio thread
is blocked, i.e. the main thread (or iothread) can't fill in more data
there. The buffer processing time is roughly real-time due to the
pa_simple_write() call blocking when the output queue to the pulse
server is full. Thus processing big chunks at once means blocking
a large part of the buffer for a long time. This brings high latency
and can lead to dropouts.
When processing the buffer in smaller chunks the rpos handling becomes a
problem though. The thread reads hw->rpos without knowing whenever
qpa_run_out has already seen the last (small) chunk processed and
updated rpos accordingly. There is no point in reading hw->rpos though,
pa->rpos can be used instead. We just need to take care to initialize
pa->rpos before kicking the thread.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: malc <av1474@comtv.ru>
use after free in do_wav_capture() on the error path.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Exception index of address read error should be 0x0e0.
Signed-off-by: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
In cpu_sh4_invalidate_tlb, the UTLB was invalidated twice and the
ITLB left unchaged, probably because of some unfortunate copy/paste.
Signed-off-by: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This register is activated by CPU_FEATURE_ASR17 in the feature field.
Signed-off-by: Fabien Chouteau <chouteau@adacore.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Leon3 is an open-source VHDL System-On-Chip, well known in space industry (more
information on http://www.gaisler.com).
Leon3 is made of multiple components available in the GrLib VHDL library.
Three devices are implemented: uart, timers and IRQ manager.
You can find code for these peripherals in the grlib_* files.
Signed-off-by: Fabien Chouteau <chouteau@adacore.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This device exposes one parameter:
- chardev (ptr) : Pointer to a qemu character device
Emulation of GrLib devices is base on the GRLIB IP Core User's Manual:
http://www.gaisler.com/products/grlib/grip.pdf
Signed-off-by: Fabien Chouteau <chouteau@adacore.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This device exposes two parameters:
- set_pil_in (ptr) : A function to set the pil_in of the SPARC CPU
- set_pil_in_opaque (ptr) : Opaque argument of the set_pil_in function
Emulation of GrLib devices is base on the GRLIB IP Core User's Manual:
http://www.gaisler.com/products/grlib/grip.pdf
Signed-off-by: Fabien Chouteau <chouteau@adacore.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This device exposes three parameters:
- frequency (uint32) : The system frequency
- irq-line (uint32) : IRQ line number for the first timer
(others use irq-line + 1, irq-line + 2...)
- nr-timers (uint32) : Number of timers
Emulation of GrLib devices is base on the GRLIB IP Core User's Manual:
http://www.gaisler.com/products/grlib/grip.pdf
Signed-off-by: Fabien Chouteau <chouteau@adacore.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
USB Mass Storage Devices sometimes have the RMB (removable) bit set in
the SCSI INQUIRY response. Thumbdrives tend to have the bit set whereas
hard disks do not.
Operating systems differentiate between removable devices and fixed
devices. Under Linux, the anaconda installer looks for removable
devices. Under Windows, only fixed devices may have more than one
partition and AutoRun is also affected by the removable bit.
For these reasons, allow USB Mass Storage Devices to override the
removable bit:
qemu -usb
-drive if=none,file=test.img,cache=none,id=disk0
-device usb-storage,drive=disk0,removable=on
The default is off.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
scsi-disk devices may wish to override the removable bit. Add support
for a qdev property on SCSI devices. This is will be used by usb-msd.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Provide the "removable" qdev property bit to override the SCSI INQUIRY
removable (RMB) bit for non-CDROM devices. This will be used by USB
Mass Storage Devices, which sometimes have this guest-visible bit set
and sometimes do not. They therefore requires a means for user
configuration.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The rule is:
- don't save PC if the exception is only triggered by softmmu.
- save PC if the exception can be triggered by an helper.
Fix a 64-bit kernel crash when loading modules.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Avoid this warning from OpenBSD linker:
LINK i386-softmmu/qemu
../usb-bus.o(.text+0x27c): In function `usb_get_fw_dev_path':
/src/qemu/hw/usb-bus.c:294: warning: sprintf() is often misused,
please use snprintf()
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Yes, seriously. There is no migration support at all for usb devices.
They loose state, especially the device address, and stop responding
because of that. Oops.
Luckily there is so much broken usb hardware out there that the guest
usually just kicks the device hard (via port reset and
reinitialization), then continues without a hitch. So we got away with
that in a surprising high number of cases.
The arrival of remote wakeup (which enables autosuspend support) changes
that picture though. The usb devices also forget that it they are
supposed to wakeup, so they don't do that. The host also doesn't notice
the device stopped working in case it suspended the device and thus
expects it waking up instead of polling it. Result is that your mouse
is dead.
Lets start fixing that. Add a vmstate struct for USBDevice.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This patch makes the numlock+capslock tracking logic only look at
keydown events. Without this patch the vnc server will insert
bogous capslock keypress in case it sees the following key sequence:
shift down --- 'A' down --- shift up --- 'A' up
^ here
It doesn't hurt with a PS/2 keyboard, but it disturbs the USB Keyboard.
And with the key event queue just added to the usb keyboard the guest
will actually notice.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This patch moves the 'head' and 'n' fields from USBMouseState and
USBKeyboardState to the common USBHIDState struct.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This patch adds a event queue to the usb keyboard. This makes sure the
guest will see all key events even if they come in bursts. With this
patch applied sending Ctrl-Alt-Del using vncviewer's F8 menu works.
Also with autosuspend enabled the first keypress on a suspended keyboard
takes a little longer to be delivered to the guest because the usb bus
must be resumed first. Without event queue this easily gets lost.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The polling nature of the USB HID device makes it very hard to double
click or drag while on a high-latency VNC connection. This patch,
based on work done in the Xen qemu-dm tree by Ian Jackson, fixes this
bug by adding an event queue to the device. The event queue associates
each movement with the correct button state, and remembers all button
presses and releases as well.
Signed-off-by: Ian Jackson <ian.jackson@eu.citrix.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Gerd Hoffman <kraxel@redhat.com>
The backing format should be honored during image creation. For some
reason we currently use the image format to open the backing file. This
fails when the backing file has a different format than the image being
created. Keep the image and backing format drivers completely separate.
Also print the backing filename if there is an error opening the backing
file instead of the image filename.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Acked-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Watch this:
(qemu) drive_add 0 if=none,file=tmp.img
OK
(qemu) info block
none0: type=hd removable=0 file=tmp.img ro=0 drv=raw encrypted=0
(qemu) drive_del none0
Segmentation fault (core dumped)
do_drive_del()'s code to clean up the pointer from a qdev using the
drive back to the drive needs to check whether such a device exists.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This makes the errors point to the error location, and fixes drive_add
to report errors in the monitor instead of stderr.
While there, tweak a few error messages for consistency.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
When cyls, heads or secs are out of range, the error message prints
buf, which points to the value of option "if". Bogus, may even be
null. Drop that.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
b02bea3a85 added a check on the return
value of bdrv_write and aborts migration when it fails. However, if the
size of the block device to migrate is not a multiple of BLOCK_SIZE
(currently 1 MB), the last bdrv_write will fail with -EIO.
Fixed by calling bdrv_write with the correct size of the last block.
Signed-off-by: Pierre Riteau <Pierre.Riteau@irisa.fr>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
QED relies on the underlying filesystem to extend the file and maintain
its size. Check that images are not created on a block device.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
