Running
git grep '\$here' tests/qemu-iotests
has 0 hits, which means we are setting a variable that has
no use. It appears that commit e8f8624d removed the last
use. So execute the following cmd to remove all of
the 'here=...' lines as dead code.
sed -i '/^here=/d' $(git grep -l '^here=' tests/qemu-iotests)
Cc: kwolf@redhat.com
Cc: mreitz@redhat.com
Cc: eblake@redhat.com
Suggested-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Mao Zhongyi <maozhongyi@cmss.chinamobile.com>
Message-Id: <20181024094051.4470-3-maozhongyi@cmss.chinamobile.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
[eblake: touch up commit message, reorder series, rebase to master]
Signed-off-by: Eric Blake <eblake@redhat.com>
When we have a BDS with unallocated clusters, but asking the status
of its underlying bs->file or backing layer encounters an end-of-file
condition, we know that the rest of the unallocated area will read as
zeroes. However, pre-patch, this required two separate calls to
bdrv_get_block_status(), as the first call stops at the point where
the underlying file ends. Thanks to BDRV_BLOCK_EOF, we can now widen
the results of the primary status if the secondary status already
includes BDRV_BLOCK_ZERO.
In turn, this fixes a TODO mentioned in iotest 154, where we can now
see that all sectors in a partial cluster at the end of a file read
as zero when coupling the shorter backing file's status along with our
knowledge that the remaining sectors came from an unallocated cluster.
Also, note that the loop in bdrv_co_get_block_status_above() had an
inefficent exit: in cases where the active layer sets BDRV_BLOCK_ZERO
but does NOT set BDRV_BLOCK_ALLOCATED (namely, where we know we read
zeroes merely because our unallocated clusters lie beyond the backing
file's shorter length), we still ended up probing the backing layer
even though we already had a good answer.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20170505021500.19315-3-eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
We've already improved discards to operate efficiently on the tail
of an unaligned qcow2 image; it's time to make a similar improvement
to write zeroes. The special case is only valid at the tail
cluster of a file, where we must recognize that any sectors beyond
the image end would implicitly read as zero, and therefore should
not penalize our logic for widening a partial cluster into writing
the whole cluster as zero.
However, note that for now, the special case of end-of-file is only
recognized if there is no backing file, or if the backing file has
the same length; that's because when the backing file is shorter
than the active layer, we don't have code in place to recognize
that reads of a sector unallocated at the top and beyond the backing
end-of-file are implicitly zero. It's not much of a real loss,
because most people don't use images that aren't cluster-aligned,
or where the active layer is a different size than the backing
layer (especially where the difference falls within a single cluster).
Update test 154 to cover the new scenarios, using two images of
intentionally differing length.
While at it, fix the test to gracefully skip when run as
./check -qcow2 -o compat=0.10 154
since the older format lacks zero clusters already required earlier
in the test.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20170507000552.20847-11-eblake@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Rename to bdrv_pwrite_zeroes() to let the compiler ensure we
cater to the updated semantics. Do the same for bdrv_co_write_zeroes().
Signed-off-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Add another test to 154, showing that we currently allocate a
data cluster in the top layer if any sector of the backing file
was allocated. The next patch will optimize this case.
Signed-off-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This covers some more write_zeroes cases which are relevant for the
recent qcow2 optimisations that check the allocation status of the
backing file for partial cluster write_zeroes requests.
This needs to be separate from 034 because we can only support qcow2 in
this test case for multiple reasons: We check the allocation status
after write_zeroes with 'qemu-img map' and the optimised behaviour that
produces zero clusters is only implemented in qcow2; second, the map
command returns offsets that are qcow2 specific; and finally, we also
use 512 byte clusters which aren't supported for formats like qed.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Mao Zhongyi
Eric Blake
Kevin Wolf