ide_set_irq() operates on a IDEBus; rename it as
ide_bus_set_irq() to emphasize its first argument
is a IDEBus.
Mechanical change using:
$ sed -i -e 's/ide_set_irq/ide_bus_set_irq/g' \
$(git grep -l ide_set_irq)
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230215112712.23110-11-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Only atapi.c requires the SCSI constants. No need to include
it in all files including "hw/ide/internal.h".
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230215112712.23110-7-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Swap 'buf' and 'bytes' around for consistency with
blk_co_{pread,pwrite}(), and in preparation to implement these functions
using generated_co_wrapper.
Callers were updated using this Coccinelle script:
@@ expression blk, offset, buf, bytes, flags; @@
- blk_pread(blk, offset, buf, bytes, flags)
+ blk_pread(blk, offset, bytes, buf, flags)
@@ expression blk, offset, buf, bytes, flags; @@
- blk_pwrite(blk, offset, buf, bytes, flags)
+ blk_pwrite(blk, offset, bytes, buf, flags)
It had no effect on hw/block/nand.c, presumably due to the #if, so that
file was updated manually.
Overly-long lines were then fixed by hand.
Signed-off-by: Alberto Faria <afaria@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20220705161527.1054072-4-afaria@redhat.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
For consistency with other I/O functions, and in preparation to
implement it using generated_co_wrapper.
Callers were updated using this Coccinelle script:
@@ expression blk, offset, buf, bytes; @@
- blk_pread(blk, offset, buf, bytes)
+ blk_pread(blk, offset, buf, bytes, 0)
It had no effect on hw/block/nand.c, presumably due to the #if, so that
file was updated manually.
Overly-long lines were then fixed by hand.
Signed-off-by: Alberto Faria <afaria@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20220705161527.1054072-3-afaria@redhat.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
While processing ATAPI cmd_read/cmd_read_cd commands,
Logical Block Address (LBA) maybe invalid OR closer to the last block,
leading to an OOB access issues. Add range check to avoid it.
Fixes: CVE-2020-29443
Reported-by: Wenxiang Qian <leonwxqian@gmail.com>
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-Id: <20210118115130.457044-1-ppandit@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A case was reported where s->io_buffer_index can be out of range.
The report skimped on the details but it seems to be triggered
by s->lba == -1 on the READ/READ CD paths (e.g. by sending an
ATAPI command with LBA = 0xFFFFFFFF). For now paper over it
with assertions. The first one ensures that there is no overflow
when incrementing s->io_buffer_index, the second checks for the
buffer overrun.
Note that the buffer overrun is only a read, so I am not sure
if the assertion failure is actually less harmful than the overrun.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 20201201120926.56559-1-pbonzini@redhat.com
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The big-endian load/store functions are already provided
by "qemu/bswap.h".
Avoid code duplication, use the generic API.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190808130454.9930-1-philmd@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
@iov is used only to initialize @qiov. Let's use new
qemu_iovec_init_buf() instead, which simplifies the code.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190218140926.333779-18-vsementsov@virtuozzo.com
Message-Id: <20190218140926.333779-18-vsementsov@virtuozzo.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
@iov is used only to initialize @qiov. Let's use new
qemu_iovec_init_buf() instead, which simplifies the code.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190218140926.333779-16-vsementsov@virtuozzo.com
Message-Id: <20190218140926.333779-16-vsementsov@virtuozzo.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
For the case where the end_transfer_func is also the caller of
ide_transfer_start, the mutual recursion can lead to unlimited
stack usage. Introduce a new version that can be used to change
tail recursion into a loop, and use it in trace_ide_atapi_cmd_reply_end.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180606190955.20845-8-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
The ATAPI_INT_REASON_IO interrupt is raised when I/O starts, but in the
AHCI case ide_set_irq was actually called at the end of a mutual recursion.
Move it early, with the side effect that ide_transfer_start becomes a tail
call in ide_atapi_cmd_reply_end.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180606190955.20845-7-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20170901001502.29915-6-jsnow@redhat.com
[Edited enum conditional for Clang --js]
Signed-off-by: John Snow <jsnow@redhat.com>
As part of the ongoing effort to modernize the tracing facilities for
the IDE family of devices, remove PRINTFs in the ATAPI device with
actual tracing events.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20170901001502.29915-5-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
For the purposes of byte_count_limit verification, add a new flag that
identifies read_cd as sometimes returning data, then check the BCL in
its command handler after we know that it will indeed return data.
Reported-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Message-id: 1477970211-25754-2-git-send-email-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
Followup to 87ac25fd, this time for ATAPI DMA.
Reported-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1470164128-28158-1-git-send-email-jsnow@redhat.com
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Sector-based blk_read() should die; switch to byte-based
blk_pread() instead.
Add new defines ATAPI_SECTOR_BITS and ATAPI_SECTOR_SIZE to
use anywhere we were previously scaling BDRV_SECTOR_* by 4,
for better legibility.
Signed-off-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Restart of ATAPI DMA used to be unreachable, because the request to do
so wasn't indicated in bus->error_status due to the lack of spare bits, and
ide_restart_bh() would return early doing nothing.
This patch makes use of the observation that not all bit combinations were
possible in ->error_status. In particular, IDE_RETRY_READ only made sense
together with IDE_RETRY_DMA or IDE_RETRY_PIO. This allows to re-use
IDE_RETRY_READ alone as an indicator of ATAPI DMA restart request.
To makes things more uniform, ATAPI DMA gets its own value for ->dma_cmd.
As a means against confusion, macros are added to test the state of
->error_status.
The patch fixes the restart of both in-flight and pending ATAPI DMA,
following the scheme similar to that of IDE DMA.
[Including a fixup patch:
Message-id: 1460465594-15777-1-git-send-email-pbutsykin@virtuozzo.com
--js]
Signed-off-by: Pavel Butsykin <pbutsykin@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 1459924806-306-4-git-send-email-den@openvz.org
Signed-off-by: John Snow <jsnow@redhat.com>
ide_atapi_dma_restart() used to just complete the DMA with an error,
under the assumption that there isn't enough information to restart it.
However, as the contents of the ->io_buffer is preserved, it looks safe to
just re-evaluate it and dispatch the ATAPI command again.
Signed-off-by: Pavel Butsykin <pbutsykin@virtuozzo.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 1459924806-306-3-git-send-email-den@openvz.org
Signed-off-by: John Snow <jsnow@redhat.com>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-17-git-send-email-peter.maydell@linaro.org
The "return;" statements at the end of functions do not make
much sense, so let's remove them.
Cc: qemu-block@nongnu.org
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Commit 5f81724d made PIO read requests async but didn't add the
relevant block_acct_failed() and block_acct_invalid() calls.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 9b87e09d61019c128139b6c999ed0c07f0674170.1448367341.git.berto@igalia.com
Signed-off-by: John Snow <jsnow@redhat.com>
PIO read requests on the ATAPI interface used to be sync blk requests.
This has two significant drawbacks. First the main loop hangs util an
I/O request is completed and secondly if the I/O request does not
complete (e.g. due to an unresponsive storage) Qemu hangs completely.
Note: Due to possible race conditions requests during an ongoing
elementary transfer are still sync.
Signed-off-by: Peter Lieven <pl@kamp.de>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 1447345846-15624-2-git-send-email-pl@kamp.de
Signed-off-by: John Snow <jsnow@redhat.com>
If we don't know about the command at all, we need to prioritize
that failure above the zero byte-count-limit failure.
This fixes a failure in the sparc64 NetBSD 7.0 installer bootup.
Reported-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: John Snow <jsnow@redhat.com>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-id: 1447095959-10046-3-git-send-email-jsnow@redhat.com
We're supposed to abort on transfers like this, unless we fill
Word 125 of our IDENTIFY data with a default transfer size, which
we don't currently do.
This is an ATA error, not a SCSI/ATAPI one.
See ATA8-ACS3 sections 7.17.6.49 or 7.21.5.
If we don't do this, QEMU will loop forever trying to transfer
zero bytes, which isn't particularly useful.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-id: 1442253685-23349-2-git-send-email-jsnow@redhat.com
The command must be completed on all code paths. START STOP UNIT with
pwrcnd set should succeed without doing anything.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Resetting the io_buffer_index to 0 is commonized,
with the exception of the case within ide_atapi_cmd_reply,
where we need to reset this index to 0 prior to the
ide_atapi_cmd_reply_end call.
Note that not all calls to ide_atapi_cmd_reply_end
expect the index to be 0, so setting it there is
not appropriate.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1424708286-16483-12-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
(With the previous atapi_dma flag recovery)
If migration happens between the ATAPI command being written and the
bmdma being started, the DMA is dropped. Eventually the guest times
out and recovers, but that can take many seconds.
(This is rare, on a pingpong reading the CD continuously I hit
this about ~1/30-1/50 migrates)
I don't think we've got enough state to be able to recover safely
at this point, so I throw a 'medium error, no seek complete'
that I'm assuming guests will try and recover from an apparently
dirty CD.
OK, it's a hack, the real solution is probably to push a lot of
ATAPI state into the migration stream, but this is a fix that
works with no stream changes. Tested only on Linux (both RHEL5
(pre-libata) and RHEL7).
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
SCSI devices have multiple kinds of queries they need to respond
to, as defined in the "cmd inquiry" section in MMC-6 and SPC-3.
Relevent sections:
MMC-6 revision 2g:
Non-VPD response data and pointer to SPC-3;
Section 6.8 "Inquiry Command"
SPC-3 revision 23:
Inquiry command and error handling:
Section 6.4 "INQUIRY command"
VPD data pages format:
Section 7.6 "Vital product data parameters"
We implement these Vital Product Data queries for SCSI, but not for
ATAPI through IDE. The result is that if you are looking for the WWN
identifier via tools such as sg3_utils, you will be unable to query
our CD/DVD rom device to obtain it.
This patch adds the minimum number of mandatory responses as defined
by SPC-3, which include the "supported pages" response (page 0x00)
and the "Device Identification" response (page 0x83). It also correctly
responds when it receives a request for an illegal page to improve
error output from related tools.
The Device ID page contains an arbitrary list of identification
strings of various formats; the ID strings included in this patch
were chosen to mimic those provided by the libata driver when
emulating this SCSI query (model, serial, and wwn when present.)
Example:
# libata emulated response
[root@localhost ~]# sg_inq --id /dev/sda
VPD INQUIRY: Device Identification page
Designation descriptor number 1, descriptor length: 24
designator_type: vendor specific [0x0], code_set: ASCII
associated with the addressed logical unit
vendor specific: QM00001
Designation descriptor number 2, descriptor length: 72
designator_type: T10 vendor identification, code_set: ASCII
associated with the addressed logical unit
vendor id: ATA
vendor specific: QEMU HARDDISK QM00001
# QEMU generated ATAPI response, with WWN
[root@localhost ~]# sg_inq --id /dev/sr0
VPD INQUIRY: Device Identification page
Designation descriptor number 1, descriptor length: 24
designator_type: vendor specific [0x0], code_set: ASCII
associated with the addressed logical unit
vendor specific: QM00005
Designation descriptor number 2, descriptor length: 72
designator_type: T10 vendor identification, code_set: ASCII
associated with the addressed logical unit
vendor id: ATA
vendor specific: QEMU DVD-ROM QM00005
Designation descriptor number 3, descriptor length: 12
designator_type: NAA, code_set: Binary
associated with the addressed logical unit
NAA 5, IEEE Company_id: 0xc50
Vendor Specific Identifier: 0x15ea71bb
[0x5000c50015ea71bb]
See also: hw/scsi/scsi-disk.c, scsi_disk_emulate_inquiry()
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Device models should access their block backends only through the
block-backend.h API. Convert them, and drop direct includes of
inappropriate headers.
Just four uses of BlockDriverState are left:
* The Xen paravirtual block device backend (xen_disk.c) opens images
itself when set up via xenbus, bypassing blockdev.c. I figure it
should go through qmp_blockdev_add() instead.
* Device model "usb-storage" prompts for keys. No other device model
does, and this one probably shouldn't do it, either.
* ide_issue_trim_cb() uses bdrv_aio_discard() instead of
blk_aio_discard() because it fishes its backend out of a BlockAIOCB,
which has only the BlockDriverState.
* PC87312State has an unused BlockDriverState[] member.
The next two commits take care of the latter two.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
When the command completion code in IDE and AHCI
was unified to put all command completion inside
of a callback, "cmd_done," we neglected to
ensure that all AHCI/ATAPI command paths would
eventually register as finished. for the PCI
interface to IDE this is not a problem because
cmd_done is a nop, but the AHCI implementation
needs to send a D2H_REG_FIS and interrupt back
to the guest to inform of completion.
This patch adds calls to ide_stop_transfer,
which calls ide_cmd_done, inside of
ide_atapi_cmd_ok and ide_atapi_cmd_error.
This fixes regressions observed by trying to boot QEMU
with a Fedora 20 live CD under Q35/AHCI, which uses
ATAPI command 0x00, which is a status check that may
cause a hang because we never complete, and ATAPI
command 0x56, which is unsupported by our current
implementation and results in an error that we never
report back to the guest.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This is the next step for decoupling block accounting functions from
BlockDriverState.
In a future commit the BlockAcctStats structure will be moved from
BlockDriverState to the device models structures.
Note that bdrv_get_stats was introduced so device models can retrieve the
BlockAcctStats structure of a BlockDriverState without being aware of it's
layout.
This function should go away when BlockAcctStats will be embedded in the device
models structures.
CC: Kevin Wolf <kwolf@redhat.com>
CC: Stefan Hajnoczi <stefanha@redhat.com>
CC: Keith Busch <keith.busch@intel.com>
CC: Anthony Liguori <aliguori@amazon.com>
CC: "Michael S. Tsirkin" <mst@redhat.com>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Eric Blake <eblake@redhat.com>
CC: Peter Maydell <peter.maydell@linaro.org>
CC: Michael Tokarev <mjt@tls.msk.ru>
CC: John Snow <jsnow@redhat.com>
CC: Markus Armbruster <armbru@redhat.com>
CC: Alexander Graf <agraf@suse.de>
CC: Max Reitz <mreitz@redhat.com>
Signed-off-by: Benoît Canet <benoit.canet@nodalink.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The middle term goal is to move the BlockAcctStats structure in the device models.
(Capturing I/O accounting statistics in the device models is good for billing)
This patch make a small step in this direction by removing a reference to BDRV.
CC: Kevin Wolf <kwolf@redhat.com>
CC: Stefan Hajnoczi <stefanha@redhat.com>
CC: Keith Busch <keith.busch@intel.com>
CC: Anthony Liguori <aliguori@amazon.com>
CC: "Michael S. Tsirkin" <mst@redhat.com>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: John Snow <jsnow@redhat.com>
CC: Richard Henderson <rth@twiddle.net>
CC: Markus Armbruster <armbru@redhat.com>
CC: Alexander Graf <agraf@suse.de>i
Signed-off-by: Benoît Canet <benoit.canet@nodalink.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
AHCI has code to fill in the D2H FIS trigger the IRQ all over the place.
Centralize this in a single cmd_done callback by generalizing the existing
async_cmd_done callback.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
It is now called only after the set_inactive callback. Put the two together.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Similar to the case removed in commit 69c38b8 (ide/core: Remove explicit
setting of BM_STATUS_INT, 2011-05-19), the only remaining use of
add_status(..., BM_STATUS_INT) is for short PRDs. The flag should
not be raised in this case.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Make it optional and prepare for the next patches.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Replace the legacy cpu_to_be16wu() with stw_be_p().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 1383669517-25598-7-git-send-email-peter.maydell@linaro.org
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
Many of these should be cleaned up with proper qdev-/QOM-ification.
Right now there are many catch-all headers in include/hw/ARCH depending
on cpu.h, and this makes it necessary to compile these files per-target.
However, fixing this does not belong in these patches.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If you have a guest with a media in the optical drive and you change
it, the windows guest cannot properly recognize this media change.
Windows needs to detect sense "NOT_READY with ASC_MEDIUM_NOT_PRESENT"
before we send sense "UNIT_ATTENTION with ASC_MEDIUM_MAY_HAVE_CHANGED".
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The START STOP UNIT command will only eject/load media if
power condition is zero.
If power condition is !0 then LOEJ and START will be ignored.
From MMC (sbc contains similar wordings too)
The Power Conditions field requests the block device to be placed
in the power condition defined in
Table 558. If this field has a value other than 0h then the Start
and LoEj bits shall be ignored.
Signed-off-by: Ronnie Sahlberg <ronniesahlberg@gmail.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This command is not necessary for CD-ROM and DVD-ROM, but some versions of
udev trip on its absence.
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It's not needed. Besides we can then assume that bdrv_eject() is
only called when there's a tray state change, which is useful to
the DEVICE_TRAY_MOVED event (going to be added in a future
commit).
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Kevin Wolf <kwolf@redhat.com>
Initially done with the following semantic patch:
@ rule1 @
expression E;
statement S;
@@
E =
(
bdrv_aio_readv
| bdrv_aio_writev
| bdrv_aio_flush
| bdrv_aio_discard
| bdrv_aio_ioctl
)
(...);
(
- if (E == NULL) { ... }
|
- if (E)
{ <... S ...> }
)
which however missed the occurrence in block/blkverify.c
(as it should have done), and left behind some unused
variables.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Mode page 2A of emulated ATAPI DVD-ROM should have page length 0x14
like SCSI CD-ROM, rather than 0x12.
Mode page length is off by 8, as it should contain the length of the
payload after the first two bytes.
MODE SENSE(6) should be thrown out of ATAPI DVD-ROM emulation. It is
not specified in the ATAPI list of MMC-2, and MMC-5 prescribes to use
MODE SENSE(10). Anyway, its implementation is wrong.
Reported-by: Thomas Schmitt <scdbackup@gmx.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
