Orginal qemu commit hash:14d02cfbe4adaeebe7cb833a8cc71191352cf03b
In function pcie_add_capability, an assert contains the
"offset < offset + size" expression.
Both variable offset and variable size are uint16_t,
the comparison is always true due to type promotion.
The next expression may be the same.
It might be like this:
Thread 1 "qemu-system-x86" hit Breakpoint 1, pcie_add_capability (
dev=0x555557ce5f10, cap_id=1, cap_ver=2 '\002', offset=256, size=72)
at ../hw/pci/pcie.c:930
930 {
(gdb) n
931 assert(offset >= PCI_CONFIG_SPACE_SIZE);
(gdb) n
932 assert(offset < offset + size);
(gdb) p offset
$1 = 256
(gdb) p offset < offset + size
$2 = 1
(gdb) set offset=65533
(gdb) p offset < offset + size
$3 = 1
(gdb) p offset < (uint16_t)(offset + size)
$4 = 0
Signed-off-by: Daniella Lee <daniellalee111@gmail.com>
Message-Id: <20211126061324.47331-1-daniellalee111@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add an expire time for pending delete, once the time is over allow
pressing the attention button again.
This makes pcie hotplug behave more like acpi hotplug, where one can
try sending an 'device_del' monitor command again in case the guest
didn't respond to the first attempt.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20211111130859.1171890-7-kraxel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In case the slot is powered off (and the power indicator turned off too)
we can unplug right away, without round-trip to the guest.
Also clear pending attention button press, there is nothing to care
about any more.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20211111130859.1171890-6-kraxel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
No functional change.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20211111130859.1171890-5-kraxel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Refuse to push the attention button in case the guest is busy with some
hotplug operation (as indicated by the power indicator blinking).
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20211111130859.1171890-4-kraxel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
With this patch hot-plugged pci devices will only be visible to the
guest if the guests hotplug driver has enabled slot power.
This should fix the hot-plug race which one can hit when hot-plugging
a pci device at boot, while the guest is in the middle of the pci bus
scan.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20211111130859.1171890-3-kraxel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This allows to power off pci devices. In "off" state the devices will
not be visible. No pci config space access, no pci bar access, no dma.
Default state is "on", so this patch (alone) should not change behavior.
Use case: Allows hotplug controllers implement slot power. Hotplug
controllers doing so should set the inital power state for devices in
the ->plug callback.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20211111130859.1171890-2-kraxel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Mark property as experimental/internal adding 'x-' prefix.
Property was introduced in 6.1 and it should have provided
ability to turn on native PCIE hotplug on port even when
ACPI PCI hotplug is in use is user explicitly sets property
on CLI. However that never worked since slot is wired to
ACPI hotplug controller.
Another non-intended usecase: disable native hotplug on slot
when APCI based hotplug is disabled, which works but slot has
'hotplug' property for this taks.
It should be relatively safe to rename it to experimental
as no users should exist for it and given that the property
is broken we don't really want to leave it around for much
longer lest users start using it.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Ani Sinha <ani@anisinha.ca>
Message-Id: <20211112110857.3116853-2-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
They're actually more commonly used than the helper without _under_bus, because
most callers do have the pci bus on hand. After exporting we can switch a lot
of the call sites to use these two helpers.
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20211028043129.38871-3-peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
They're used in quite a few places of pci.[ch] and also in the rest of the code
base. Define them so that it doesn't need to be defined all over the places.
The pci_bus_fn is similar to pci_bus_dev_fn that only takes a PCIBus* and an
opaque. The pci_bus_ret_fn is similar to pci_bus_fn but it allows to return a
void* pointer.
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20211028043129.38871-2-peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
PCI resource reserve capability should use LE format as all other PCI
things. If we don't then seabios won't boot:
=== PCI new allocation pass #1 ===
PCI: check devices
PCI: QEMU resource reserve cap: size 10000000000000 type io
PCI: secondary bus 1 size 10000000000000 type io
PCI: secondary bus 1 size 00200000 type mem
PCI: secondary bus 1 size 00200000 type prefmem
=== PCI new allocation pass #2 ===
PCI: out of I/O address space
This became more important since we started reserving IO by default,
previously no one noticed.
Fixes: e2a6290aab ("hw/pcie-root-port: Fix hotplug for PCI devices requiring IO")
Cc: marcel.apfelbaum@gmail.com
Fixes: 226263fb5c ("hw/pci: add QEMU-specific PCI capability to the Generic PCI Express Root Port")
Cc: zuban32s@gmail.com
Fixes: 6755e618d0 ("hw/pci: add PCI resource reserve capability to legacy PCI bridge")
Cc: jing2.liu@linux.intel.com
Tested-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Rename the "allocate and return" qbus creation function to
qbus_new(), to bring it into line with our _init vs _new convention.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Message-id: 20210923121153.23754-6-peter.maydell@linaro.org
Rename qbus_create_inplace() to qbus_init(); this is more in line
with our usual naming convention for functions that in-place
initialize objects.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20210923121153.23754-5-peter.maydell@linaro.org
Rename the pci_root_bus_new_inplace() function to
pci_root_bus_init(); this brings the bus type in to line with a
"_init for in-place init, _new for allocate-and-return" convention.
To do this we need to rename the implementation-internal function
that was using the pci_root_bus_init() name to
pci_root_bus_internal_init().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20210923121153.23754-4-peter.maydell@linaro.org
This helps to get the min and max bus number of a PCI bus hierarchy.
Signed-off-by: Xingang Wang <wangxingang5@huawei.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <1625748919-52456-6-git-send-email-wangxingang5@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add a new bypass_iommu property for PCI host and use it to check
whether devices attached to the PCI root bus will bypass iommu.
In pci_device_iommu_address_space(), check the property and
avoid getting iommu address space for devices bypass iommu.
Signed-off-by: Xingang Wang <wangxingang5@huawei.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <1625748919-52456-2-git-send-email-wangxingang5@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Instead of changing the hot-plug type in _OSC register, do not
set the 'Hot-Plug Capable' flag. This way guest will choose ACPI
hot-plug if it is preferred and leave the option to use SHPC with
pcie-pci-bridge.
The ability to control hot-plug for each downstream port is retained,
while 'hotplug=off' on the port means all hot-plug types are disabled.
Signed-off-by: Julia Suvorova <jusual@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20210713004205.775386-4-jusual@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Commit e50caf4a5c ("tracing: convert documentation to rST")
converted docs/devel/tracing.txt to docs/devel/tracing.rst.
We still have several references to the old file, so let's fix them
with the following command:
sed -i s/tracing.txt/tracing.rst/ $(git grep -l docs/devel/tracing.txt)
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210517151702.109066-2-sgarzare@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Stop including exec/address-spaces.h in files that don't need it.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210416171314.2074665-5-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Commit 4c70875372 ("pci: advertise a page aligned ATS") advertises
the page aligned via ATS capability (RO) to unbrek recent Linux IOMMU
drivers since 5.2. But it forgot the compat the capability which
breaks the migration from old machine type:
(qemu) qemu-kvm: get_pci_config_device: Bad config data: i=0x104 read:
0 device: 20 cmask: ff wmask: 0 w1cmask:0
This patch introduces a new parameter "x-ats-page-aligned" for
virtio-pci device and turns it on for machine type which is newer than
5.1.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: qemu-stable@nongnu.org
Fixes: 4c70875372 ("pci: advertise a page aligned ATS")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20210406040330.11306-1-jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
If a device model
(a) doesn't set the value to a correct interrupt number and then
(b) triggers an interrupt for itself,
it's device model bug. Add assert on interrupt pin number to catch
this kind of bug more obviously.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Isaku Yamahata <isaku.yamahata@intel.com>
Message-Id: <9cf8ac3b17e162daac0971d7be32deb6a33ae6ec.1616532563.git.isaku.yamahata@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In x86/ACPI world, linux distros are using predictable
network interface naming since systemd v197. Which on
QEMU based VMs results into path based naming scheme,
that names network interfaces based on PCI topology.
With itm on has to plug NIC in exactly the same bus/slot,
which was used when disk image was first provisioned/configured
or one risks to loose network configuration due to NIC being
renamed to actually used topology.
That also restricts freedom to reshape PCI configuration of
VM without need to reconfigure used guest image.
systemd also offers "onboard" naming scheme which is
preferred over PCI slot/topology one, provided that
firmware implements:
"
PCI Firmware Specification 3.1
4.6.7. DSM for Naming a PCI or PCI Express Device Under
Operating Systems
"
that allows to assign user defined index to PCI device,
which systemd will use to name NIC. For example, using
-device e1000,acpi-index=100
guest will rename NIC to 'eno100', where 'eno' is default
prefix for "onboard" naming scheme. This doesn't require
any advance configuration on guest side to com in effect
at 'onboard' scheme takes priority over path based naming.
Hope is that 'acpi-index' it will be easier to consume by
management layer, compared to forcing specific PCI topology
and/or having several disk image templates for different
topologies and will help to simplify process of spawning
VM from the same template without need to reconfigure
guest NIC.
This patch adds, 'acpi-index'* property and wires up
a 32bit register on top of pci hotplug register block
to pass index value to AML code at runtime.
Following patch will add corresponding _DSM code and
wire it up to PCI devices described in ACPI.
*) name comes from linux kernel terminology
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20210315180102.3008391-3-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
While pci_bus_realize() currently does not use the Error* argument,
it would be an error to leave pcie_bus_realize() setting bus->flags
if pci_bus_realize() had failed.
Fix by using a local Error* and return early (propagating the error)
if pci_bus_realize() failed.
Reported-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210201153700.618946-1-philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When the pcie slot is initialized, by default PCI_EXP_LNKSTA_DLLLA
(Data Link Layer Link Active) is set in PCI_EXP_LNKSTA
(Link Status) without checking if the slot is empty or not.
This is confusing for the kernel because as it sees the link is up
it tries to read the vendor ID and fails:
(From https://bugzilla.kernel.org/show_bug.cgi?id=211691)
[ 1.661105] pcieport 0000:00:02.2: pciehp: Slot Capabilities : 0x0002007b
[ 1.661115] pcieport 0000:00:02.2: pciehp: Slot Status : 0x0010
[ 1.661123] pcieport 0000:00:02.2: pciehp: Slot Control : 0x07c0
[ 1.661138] pcieport 0000:00:02.2: pciehp: Slot #0 AttnBtn+ PwrCtrl+ MRL- AttnInd+ PwrInd+ HotPlug+ Surprise+ Interlock+ NoCompl- IbPresDis- LLActRep+
[ 1.662581] pcieport 0000:00:02.2: pciehp: pciehp_get_power_status: SLOTCTRL 6c value read 7c0
[ 1.662597] pcieport 0000:00:02.2: pciehp: pciehp_check_link_active: lnk_status = 2204
[ 1.662703] pcieport 0000:00:02.2: pciehp: pending interrupts 0x0010 from Slot Status
[ 1.662706] pcieport 0000:00:02.2: pciehp: pcie_enable_notification: SLOTCTRL 6c write cmd 1031
[ 1.662730] pcieport 0000:00:02.2: pciehp: pciehp_check_link_active: lnk_status = 2204
[ 1.662748] pcieport 0000:00:02.2: pciehp: pciehp_check_link_active: lnk_status = 2204
[ 1.662750] pcieport 0000:00:02.2: pciehp: Slot(0-2): Link Up
[ 2.896132] pcieport 0000:00:02.2: pciehp: pciehp_check_link_status: lnk_status = 2204
[ 2.896135] pcieport 0000:00:02.2: pciehp: Slot(0-2): No device found
[ 2.896900] pcieport 0000:00:02.2: pciehp: pending interrupts 0x0010 from Slot Status
[ 2.896903] pcieport 0000:00:02.2: pciehp: pciehp_power_off_slot: SLOTCTRL 6c write cmd 400
[ 3.656901] pcieport 0000:00:02.2: pciehp: pending interrupts 0x0009 from Slot Status
This is really a problem with virtio-net failover that hotplugs a VFIO
card during the boot process. The kernel can shutdown the slot while
QEMU is hotplugging it, and this likely ends by an automatic unplug of
the card. At the end of the boot sequence the card has disappeared.
To fix that, don't set the "Link Active" state in the init function, but
rely on the plug function to do it, as the mechanism has already been
introduced by 2f2b18f60b.
Fixes: 2f2b18f60b ("pcie: set link state inactive/active after hot unplug/plug")
Cc: zhengxiang9@huawei.com
Fixes: 3d67447fe7 ("pcie: Fill PCIESlot link fields to support higher speeds and widths")
Cc: alex.williamson@redhat.com
Fixes: b2101eae63 ("pcie: Set the "link active" in the link status register")
Cc: benh@kernel.crashing.org
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Message-Id: <20210212135250.2738750-5-lvivier@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Commit a1190ab628 has added a "allow_unplug_during_migration = true" at
the end of the main "if" block, so it is not needed to set it anymore
in the previous checking.
Remove it, to have only sub-ifs that check for needed conditions and exit
if one fails.
Fixes: 4f5b6a05a4 ("pci: add option for net failover")
Fixes: a1190ab628 ("migration: allow unplug during migration for failover devices")
Cc: jfreimann@redhat.com
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Message-Id: <20210212135250.2738750-2-lvivier@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Jens Freimann <jfreimann@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
This property can be useful for distros to set up known-good ROM sizes for
migration purposes. The VM will fail to start if the ROM is too large,
and migration compatibility will not be broken if the ROM is too small.
Note that even though romsize is a uint32_t, it has to be between 1
(because empty ROM files are not accepted, and romsize must be greater
than the file) and 2^31 (because values above are not powers of two and
are rejected).
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Message-Id: <20201218182736.1634344-1-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210203131828.156467-3-pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: David Edmondson <david.edmondson@oracle.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
get_image_size() returns an int64_t, which pci_add_option_rom() assigns
to an "int" without any range checking. A 32-bit BAR could be up to
2 GiB in size, so reject anything above it. In order to accomodate
a rounded-up size of 2 GiB, change pci_patch_ids's size argument
to unsigned.
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210203131828.156467-2-pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: David Edmondson <david.edmondson@oracle.com>
These cases require a bit more thought to review; in each case, the
code was appending to a list, but not with a FOOList **tail variable.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20210113221013.390592-6-eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[Flawed change to qmp_guest_network_get_interfaces() dropped]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
When the slot is in steady powered-off state and the device is being
removed, there's no need to press the attention button. Nor is it
mandated by the Standard Hot-Plug Controller Specification, Rev. 1.0.
Moreover it confuses the guest, Linux in particular, as it assumes that
the attention button pressed in this state indicates that the device has
been inserted and will need to be powered on. Therefore it transitions
the slot into BLINKING_ON state for 5 seconds, and discovers at the end
that no device is actually inserted:
... unplug request
[12685.451329] shpchp 0000:01:00.0: Button pressed on Slot(2)
[12685.455478] shpchp 0000:01:00.0: PCI slot #2 - powering off due to button press
... in 5 seconds OS powers off the slot, QEMU ejects the device
[12690.632282] shpchp 0000:01:00.0: Latch open on Slot(2)
... excessive button press in steady powered-off state
[12690.634267] shpchp 0000:01:00.0: Button pressed on Slot(2)
[12690.636256] shpchp 0000:01:00.0: Card not present on Slot(2)
... the last button press spawns powering on the slot
[12690.638909] shpchp 0000:01:00.0: PCI slot #2 - powering on due to button press
... in 5 more seconds attempt to power on discovers empty slot
[12695.735986] shpchp 0000:01:00.0: No adapter on slot(2)
Worse, if the real device insertion happens within 5 seconds from the
apparent completion of the previous device removal (signaled via
DEVICE_DELETED event), the new button press will be interpreted as the
cancellation of that misguided powering on:
[13448.965295] shpchp 0000:01:00.0: Button pressed on Slot(2)
[13448.969430] shpchp 0000:01:00.0: PCI slot #2 - powering off due to button press
[13454.025107] shpchp 0000:01:00.0: Latch open on Slot(2)
[13454.027101] shpchp 0000:01:00.0: Button pressed on Slot(2)
[13454.029165] shpchp 0000:01:00.0: Card not present on Slot(2)
... the excessive button press spawns powering on the slot
... device has already been ejected by QEMU
[13454.031949] shpchp 0000:01:00.0: PCI slot #2 - powering on due to button press
... new device is inserted in the slot
[13456.861545] shpchp 0000:01:00.0: Latch close on Slot(2)
... valid button press arrives before 5 s since the wrong one
[13456.864894] shpchp 0000:01:00.0: Button pressed on Slot(2)
[13456.869211] shpchp 0000:01:00.0: Card present on Slot(2)
... the valid button press is counted as cancellation of the wrong one
[13456.873173] shpchp 0000:01:00.0: Button cancel on Slot(2)
[13456.877101] shpchp 0000:01:00.0: PCI slot #2 - action canceled due to button press
As a result, the newly inserted device isn't brought up by the guest.
Avoid this situation by not pushing the attention button when the device
in the slot is in powered-off state and is being ejected.
FWIW pcie implementation doesn't suffer from this problem.
Signed-off-by: Roman Kagan <rvkagan@yandex-team.ru>
Message-Id: <20201102053750.2281818-1-rvkagan@yandex-team.ru>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Commit 8118f0950f "migration: Append JSON description of migration
stream" needs a JSON writer. The existing qobject_to_json() wasn't a
good fit, because it requires building a QObject to convert. Instead,
migration got its very own JSON writer, in commit 190c882ce2 "QJSON:
Add JSON writer". It tacitly limits numbers to int64_t, and strings
contents to characters that don't need escaping, unlike
qobject_to_json().
The previous commit factored the JSON writer out of qobject_to_json().
Replace migration's JSON writer by it.
Cc: Juan Quintela <quintela@redhat.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20201211171152.146877-17-armbru@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Move the property types and property macros implemented in
qdev-properties-system.c to a new qdev-properties-system.h
header.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20201211220529.2290218-16-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Generalize the qdev_hotplug variable to the different phases of
machine initialization. We would like to allow different
monitor commands depending on the phase.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Prevent future developers working on root complexes, root ports, or
bridges that also wish to implement a BAR for those, from shooting
themselves in the foot. PCI type 1 headers only support 2 base address
registers. It is incorrect and difficult to figure out what is wrong
with the device when this mistake is made. With this, it is immediate
and obvious what has gone wrong.
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Message-Id: <20201015181411.89104-2-ben.widawsky@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Asserts are used for developer bugs. As registering a bar of the wrong
size is not something that should be possible for a user to achieve,
this is a developer bug.
While here, use the more obvious helper function.
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Message-Id: <20201015181411.89104-1-ben.widawsky@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
After Linux kernel commit 61363c1474b1 ("iommu/vt-d: Enable ATS only
if the device uses page aligned address."), ATS will be only enabled
if device advertises a page aligned request.
Unfortunately, vhost-net is the only user and we don't advertise the
aligned request capability in the past since both vhost IOTLB and
address_space_get_iotlb_entry() can support non page aligned request.
Though it's not clear that if the above kernel commit makes
sense. Let's advertise a page aligned ATS here to make vhost device
IOTLB work with Intel IOMMU again.
Note that in the future we may extend pcie_ats_init() to accept
parameters like queue depth and page alignment.
Cc: qemu-stable@nongnu.org
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20200909081731.24688-1-jasowang@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
These assertions similar to those in the adjacent pci_bus_get_irq_level()
function ensure that irqnum lies within the valid PCI bus IRQ range.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20201011082022.3016-1-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201024203900.3619498-3-f4bug@amsat.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Extract pci_bus_change_irq_level() from pci_change_irq_level() to
make it clearer it operates on the bus.
Reported-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201024203900.3619498-2-f4bug@amsat.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
'occupied' is spelled like 'ocuppied' in the message.
Signed-off-by: Julia Suvorova <jusual@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20201006133958.600932-1-jusual@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Only qemu-system-FOO and qemu-storage-daemon provide QMP
monitors, therefore such declarations and definitions are
irrelevant for user-mode emulation.
Extracting the PCI commands to their own schema reduces the size of
the qapi-misc* headers generated, and pulls less QAPI-generated code
into user-mode.
Suggested-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200913195348.1064154-9-philmd@redhat.com>
[Commit message tweaked]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
When debugging QEMU it is often useful to put a breakpoint on the
error_setg_internal method impl.
Unfortunately the object_property_add / object_class_property_add
methods call object_property_find / object_class_property_find methods
to check if a property exists already before adding the new property.
As a result there are a huge number of calls to error_setg_internal
on startup of most QEMU commands, making it very painful to set a
breakpoint on this method.
Most callers of object_find_property and object_class_find_property,
however, pass in a NULL for the Error parameter. This simplifies the
methods to remove the Error parameter entirely, and then adds some
new wrapper methods that are able to raise an Error when needed.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200914135617.1493072-1-berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Meson doesn't enjoy the same flexibility we have with Make in choosing
the include path. In particular the tracing headers are using
$(build_root)/$(<D).
In order to keep the include directives unchanged,
the simplest solution is to generate headers with patterns like
"trace/trace-audio.h" and place forwarding headers in the source tree
such that for example "audio/trace.h" includes "trace/trace-audio.h".
This patch is too ugly to be applied to the Makefiles now. It's only
a way to separate the changes to the tracing header files from the
Meson rewrite of the tracing logic.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The pci host config register is used to save PCI address for
read/write config data. If guest writes a value to config register,
and then QEMU pauses the vcpu to migrate, after the migration, the guest
will continue to write pci config data, and the write data will be ignored
because of new qemu process losing the config register state.
To trigger the bug:
1. guest is booting in seabios.
2. guest enables the SMRAM in seabios:piix4_apmc_smm_setup, and then
expects to disable the SMRAM by pci_config_writeb.
3. after guest writes the pci host config register, QEMU pauses vcpu
to finish migration.
4. guest write of config data(0x0A) fails to disable the SMRAM because
the config register state is lost.
5. guest continues to boot and crashes in ipxe option ROM due to SMRAM
in enabled state.
Example Reproducer:
step 1. Make modifications to seabios and qemu for increase reproduction
efficiency, write 0xf0 to 0x402 port notify qemu to stop vcpu after
0x0cf8 port wrote i440 configure register. qemu stop vcpu when catch
0x402 port wrote 0xf0.
seabios:/src/hw/pci.c
@@ -52,6 +52,11 @@ void pci_config_writeb(u16 bdf, u32 addr, u8 val)
writeb(mmconfig_addr(bdf, addr), val);
} else {
outl(ioconfig_cmd(bdf, addr), PORT_PCI_CMD);
+ if (bdf == 0 && addr == 0x72 && val == 0xa) {
+ dprintf(1, "stop vcpu\n");
+ outb(0xf0, 0x402); // notify qemu to stop vcpu
+ dprintf(1, "resume vcpu\n");
+ }
outb(val, PORT_PCI_DATA + (addr & 3));
}
}
qemu:hw/char/debugcon.c
@@ -60,6 +61,9 @@ static void debugcon_ioport_write(void *opaque, hwaddr addr, uint64_t val,
printf(" [debugcon: write addr=0x%04" HWADDR_PRIx " val=0x%02" PRIx64 "]\n", addr, val);
#endif
+ if (ch == 0xf0) {
+ vm_stop(RUN_STATE_PAUSED);
+ }
/* XXX this blocks entire thread. Rewrite to use
* qemu_chr_fe_write and background I/O callbacks */
qemu_chr_fe_write_all(&s->chr, &ch, 1);
step 2. start vm1 by the following command line, and then vm stopped.
$ qemu-system-x86_64 -machine pc-i440fx-5.0,accel=kvm\
-netdev tap,ifname=tap-test,id=hostnet0,vhost=on,downscript=no,script=no\
-device virtio-net-pci,netdev=hostnet0,id=net0,bus=pci.0,addr=0x13,bootindex=3\
-device cirrus-vga,id=video0,vgamem_mb=16,bus=pci.0,addr=0x2\
-chardev file,id=seabios,path=/var/log/test.seabios,append=on\
-device isa-debugcon,iobase=0x402,chardev=seabios\
-monitor stdio
step 3. start vm2 to accept vm1 state.
$ qemu-system-x86_64 -machine pc-i440fx-5.0,accel=kvm\
-netdev tap,ifname=tap-test1,id=hostnet0,vhost=on,downscript=no,script=no\
-device virtio-net-pci,netdev=hostnet0,id=net0,bus=pci.0,addr=0x13,bootindex=3\
-device cirrus-vga,id=video0,vgamem_mb=16,bus=pci.0,addr=0x2\
-chardev file,id=seabios,path=/var/log/test.seabios,append=on\
-device isa-debugcon,iobase=0x402,chardev=seabios\
-monitor stdio \
-incoming tcp:127.0.0.1:8000
step 4. execute the following qmp command in vm1 to migrate.
(qemu) migrate tcp:127.0.0.1:8000
step 5. execute the following qmp command in vm2 to resume vcpu.
(qemu) cont
Before this patch, we get KVM "emulation failure" error on vm2.
This patch fixes it.
Cc: qemu-stable@nongnu.org
Signed-off-by: Hogan Wang <hogan.wang@huawei.com>
Message-Id: <20200727084621.3279-1-hogan.wang@huawei.com>
Reported-by: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
qbus_set_hotplug_handler() is a simple wrapper around
object_property_set_link().
object_property_set_link() fails when the property doesn't exist, is
not settable, or its .check() method fails. These are all programming
errors here, so passing &error_abort to qbus_set_hotplug_handler() is
appropriate.
Most of its callers do. Exceptions:
* pcie_cap_slot_init(), shpc_init(), spapr_phb_realize() pass NULL,
i.e. they ignore errors.
* spapr_machine_init() passes &error_fatal.
* s390_pcihost_realize(), virtio_serial_device_realize(),
s390_pcihost_plug() pass the error to their callers. The latter two
keep going after the error, which looks wrong.
Drop the @errp parameter, and instead pass &error_abort to
object_property_set_link().
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Daniel P. Berrangé" <berrange@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20200630090351.1247703-15-armbru@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-18-armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
