When trying to update the refcounts for a snapshot, the return value of
update_refcount on a compressed cluster was pretty much ignored,
cancelling the update on error but returning 0. This is caused by an
inner "ret" variable shadowing the outer one (the latter is used in the
return statement).
Signed-off-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
# By Stefan Hajnoczi (4) and others
# Via Stefan Hajnoczi
* stefanha/block:
virtio-blk: do not relay a previous driver's WCE configuration to the current
blockdev: do not default cache.no-flush to true
block: don't lose data from last incomplete sector
qcow2: Correct snapshots size for overlap check
coroutine: fix /perf/nesting coroutine benchmark
coroutine: add qemu_coroutine_yield benchmark
qemu-timer: do not take the lock in timer_pending
qemu-timer: make qemu_timer_mod_ns() and qemu_timer_del() thread-safe
qemu-timer: drop outdated signal safety comments
osdep: warn if open(O_DIRECT) on fails with EINVAL
libcacard: link against qemu-error.o for error_report()
Message-id: 1379698931-946-1-git-send-email-stefanha@redhat.com
# By Hervé Poussineau (5) and Stefan Weil (1)
# Via Paolo Bonzini
* bonzini/scsi-next:
block/iscsi: Drop iscsi_co_get_block_status for older versions of libiscsi
lsi: add 53C810 variant
lsi: remove todo
lsi: ignore write accesses to CTEST0 registers
lsi: check ssid versus sdid only if ssid is valid
lsi: use constant name instead of its value
Using s->snapshots_size instead of snapshots_size for the metadata
overlap check in qcow2_write_snapshots leads to the detection of an
overlap with the main qcow2 image header when deleting the last
snapshot, since s->snapshots_size has not yet been updated and is
therefore non-zero. However, the offset returned by qcow2_alloc_clusters
will be zero since snapshots_size is zero. Therefore, an overlap is
detected albeit no such will occur.
This patch fixes this by replacing s->snapshots_size by snapshots_size
when calling qcow2_pre_write_overlap_check.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Debian wheezy includes libiscsi-dev 1.4.0 which does not provide
SCSI_PROVISIONING_TYPE_DEALLOCATED. Drop iscsi_co_get_block_status
in this case to allow compilation without errors.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
# By Max Reitz (16) and others
# Via Kevin Wolf
* kwolf/for-anthony: (33 commits)
qemu-iotests: Fix test 038
block: Assert validity of BdrvActionOps
qemu-iotests: Cleanup test image in test number 007
qemu-img: fix invalid JSON
coroutine: add ./configure --disable-coroutine-pool
qemu-iotests: Adjustments due to error propagation
qcow2: Use Error parameter
qemu-img create: Emit filename on error
block: Error parameter for create functions
block: Error parameter for open functions
bdrv: Use "Error" for creating images
bdrv: Use "Error" for opening images
qemu-iotests: add 057 internal snapshot for block device test case
hmp: add interface hmp_snapshot_delete_blkdev_internal
hmp: add interface hmp_snapshot_blkdev_internal
qmp: add interface blockdev-snapshot-delete-internal-sync
qmp: add interface blockdev-snapshot-internal-sync
qmp: add internal snapshot support in qmp_transaction
snapshot: distinguish id and name in snapshot delete
snapshot: new function bdrv_snapshot_find_by_id_and_name()
...
Message-id: 1379073063-14963-1-git-send-email-kwolf@redhat.com
Replace .bdrv_aio_discard with .bdrv_co_discard so that discard
requests can be split in multiple parts, each for a small amount
of sectors.
This is useful because we expose a generic API with no limit
on the amount of sectors that can be unmapped in one request.
Signed-off-by: Peter Lieven <pl@kamp.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add an Error ** parameter to bdrv_create and its associated functions to
allow more specific error messages.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Add an Error ** parameter to bdrv_open, bdrv_file_open and associated
functions to allow more specific error messages.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Add an Error ** parameter to BlockDriver.bdrv_open and
BlockDriver.bdrv_file_open to allow more specific error messages.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Snapshot creation actually already distinguish id and name since it take
a structured parameter *sn, but delete can't. Later an accurate delete
is needed in qmp_transaction abort and blockdev-snapshot-delete-sync,
so change its prototype. Also *errp is added to tip error, but return
value is kepted to let caller check what kind of error happens. Existing
caller for it are savevm, delvm and qemu-img, they are not impacted by
introducing a new function bdrv_snapshot_delete_by_id_or_name(), which
check the return value and do the operation again.
Before this patch:
For qcow2, it search id first then name to find the one to delete.
For rbd, it search name.
For sheepdog, it does nothing.
After this patch:
For qcow2, logic is the same by call it twice in caller.
For rbd, it always fails in delete with id, but still search for name
in second try, no change to user.
Some code for *errp is based on Pavel's patch.
Signed-off-by: Wenchao Xia <xiawenc@linux.vnet.ibm.com>
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
To make it clear about id and name in searching, add this API
to distinguish them. Caller can choose to search by id or name,
*errp will be set only for exception.
Some code are modified based on Pavel's patch.
Signed-off-by: Wenchao Xia <xiawenc@linux.vnet.ibm.com>
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Implement bdrv_amend_options for compat, size, backing_file, backing_fmt
and lazy_refcounts.
Downgrading images from compat=1.1 to compat=0.10 is achieved through
handling all incompatible flags accordingly, clearing all compatible and
autoclear flags and expanding all zero clusters.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Save the image refcount order in BDRVQcowState. This will be relevant
for future code supporting different refcount orders than four and also
for code that needs to verify a certain refcount order for an opened
image.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Add functionality for expanding zero clusters. This is necessary for
downgrading the image version to one without zero cluster support.
For non-backed images, this function may also just discard zero clusters
instead of truly expanding them.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Add a function for emptying a cache, i.e., flushing it and marking all
elements invalid.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
It is a valid case that the read data's size is smaller than the
requested size since there could be files that are smaller than
the minimum block size (For ex. when a VMDK disk descriptor file)
Signed-off-by: Tal Kain <tal.kain@ravellosystems.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
During savevm, the VM state is written to the active L1 of the image and
then a snapshot is taken. After that, the VM state isn't needed any more
in the active L1 and should be discarded. This is implemented by this
patch.
The impact of not discarding the VM state is that a snapshot can never
become smaller than any previous snapshot (because it would be padded
with old VM state), and more importantly that future savevm operations
cause unnecessary COWs (with associated flushes), which makes subsequent
snapshots much slower.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
The function will be used internally instead of only being called for
guest discard requests.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
this patch adds a coroutine for .bdrv_co_block_status as well as
a generic framework that can be used to build coroutines in block/iscsi.
Signed-off-by: Peter Lieven <pl@kamp.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The UUID is unique even across multiple hosts, thus it is
better than a VM name even if it is less user-friendly.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
These are created for example with XFS_IOC_ZERO_RANGE.
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
For now, bdrv_get_block_status is just another name for bdrv_is_allocated.
The next patches will add more flags.
This also touches all block drivers with a mostly mechanical rename. The
sole exception is cow; because it calls cow_co_is_allocated from the read
code, we keep that function and make cow_co_get_block_status a wrapper.
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Some bdrv_is_allocated callers do not expect errors, but the fallback
in qcow2.c might make other callers trip on assertion failures or
infinite loops.
Fix the callers to always look for errors.
Cc: qemu-stable@nongnu.org
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Now that bdrv_is_allocated detects coroutine context, the two can
use the same code.
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
bdrv_is_allocated can detect coroutine context and go through a fast
path, similar to other block layer functions.
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
As we change bdrv_is_allocated to gather more information from bs and
bs->file, it will become a bit slower. It is still appropriate for online
jobs, but not for reads/writes. Call the internal function instead.
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Only sync once per write, rather than once per sector.
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Do not do two reads for each sector; load each sector of the bitmap
and use bitmap operations to process it.
Writes are still dog slow!
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Manage BlockDriverState lifecycle with refcnt, so bdrv_delete() is no
longer public and should be called by bdrv_unref() if refcnt is
decreased to 0.
This is an identical change because effectively, there's no multiple
reference of BDS now: no caller of bdrv_ref() yet, only bdrv_new() sets
bs->refcnt to 1, so all bdrv_unref() now actually delete the BDS.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
BlockDriverState structure needs bdrv_new() to initialize refcnt, don't
allocate a local structure variable and memset to 0, becasue with coming
refcnt implementation, bdrv_unref will crash if bs->refcnt not
initialized to 1.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
we need bdrv_new() to properly initialize BDS, don't allocate memory
manually.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
QEMU failed to open host devices like \\.\PhysicalDrive0 (first hard disk)
since some time (commit 8a79380b8ef1b02d2abd705dd026a18863b09020?).
Those devices use hdev_open which did not use the latest API for options.
This resulted in a fatal runtime error:
Block protocol 'host_device' doesn't support the option 'filename'
Duplicate code from raw_open to fix this.
Cc: qemu-stable@nongnu.org
Reported-by: David Brenner <david.brenner3@gmail.com>
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This feature can be used in case where users are avoiding the iops limit by
doing jumbo I/Os hammering the storage backend.
Signed-off-by: Benoit Canet <benoit@irqsave.net>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The max parameter of the leaky bucket throttling algorithm can be used to
allow the guest to do bursts.
The max value is a pool of I/O that the guest can use without being throttled
at all. Throttling is triggered once this pool is empty.
Signed-off-by: Benoit Canet <benoit@irqsave.net>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
If no corruptions remain after an image repair (and no errors have been
encountered), clear the corrupt flag in qcow2_check.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
If the refcount of a refcount block is greater than one, we can at least
try to repair that problem by duplicating the affected block.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Drop error code path which cannot be taken since qemu_bh_new() does not
return NULL.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Most typos were found using a modified version of codespell:
accross -> across
issueing -> issuing
TICNT_THRESHHOLD -> TICNT_THRESHOLD
bandwith -> bandwidth
VCARD_7816_PROPIETARY -> VCARD_7816_PROPRIETARY
occured -> occurred
gaurantee -> guarantee
sofware -> software
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Since the OFLAG_COPIED checks are now executed after the refcounts have
been repaired (if repairing), it is safe to assume that they are correct
but the OFLAG_COPIED flag may be not. Therefore, if its value differs
from what it should be (considering the according refcount), that
discrepancy can be repaired by correctly setting (or clearing that flag.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Move the OFLAG_COPIED checks out of check_refcounts_l1 and
check_refcounts_l2 and after the actual refcount checks/fixes (since the
refcounts might actually change there).
Signed-off-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The pre-write overlap check function is now called before most of the
qcow2 writes (aborting it on collision or other error).
Signed-off-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Two new functions are added; the first one checks a given range in the
image file for overlaps with metadata (main header, L1 tables, L2
tables, refcount table and blocks).
The second one should be used immediately before writing to the image
file as it calls the first function and, upon collision, marks the
image as corrupt and makes the BDS unusable, thereby preventing
further access.
Both functions take a bitmask argument specifying the structures which
should be checked for overlaps, making it possible to also check
metadata writes against colliding with other structures.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This adds an incompatible bit indicating corruption to qcow2. Any image
with this bit set may not be written to unless for repairing (and
subsequently clearing the bit if the repair has been successful).
Signed-off-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Account for all cluster types in qcow2_update_snapshot_refcounts;
this prevents this function from updating the refcount of unallocated
zero clusters which effectively led to wrong adjustments of the refcount
of cluster 0 (the main qcow2 header). This in turn resulted in images
with (unallocated) zero clusters having a cluster 0 refcount greater
than one after creating a snapshot.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Currently if gluster AIO callback thread fails to notify the QEMU thread about
AIO completion, we try graceful recovery by marking the disk drive as
inaccessible. This error recovery code is race-prone as found by Asias and
Stefan. However as found out by Paolo, this kind of error is impossible and
hence simplify the code that handles this error recovery.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
"Incoming" function prototypes and "outgoing" function calls must match
reality. Implemented using the "struct BlockDriver" definition in
"include/block/block_int.h", and gcc errors & warnings.
v1->v2:
On 08/20/13 09:51, Kevin Wolf wrote:
> Am 18.08.2013 um 16:29 hat Paolo Bonzini geschrieben:
>> Il 16/08/2013 16:15, Laszlo Ersek ha scritto:
>>> +static int raw_reopen_prepare(BDRVReopenState *reopen_state,
>>> + BlockReopenQueue *queue, Error **errp)
>>> {
>>> - return bdrv_reopen_prepare(bs->file);
>>> + BDRVReopenState tmp = *reopen_state;
>>> +
>>> + tmp.bs = tmp.bs->file;
>>> + return bdrv_reopen_prepare(&tmp, queue, errp);
>>> }
>>
>> This should just return zero, my fault.
>
> Which is because bdrv_reopen_queue() already queues bs->file for reopen.
> The simple return 0; implementation is shared by all other format drivers
> that support reopening images.
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
On 08/05/13 15:03, Paolo Bonzini wrote:
>
> [...]
>
> 5) Formats are registered with bdrv_register (takes a BlockDriver*). You
> also need to pass the caller of bdrv_register to block_init.
Fill in the BlockDriver structure with the raw_*() functions that have
been added to "block/raw_bsd.c", in the order the fields are defined in
"include/block/block_int.h".
I needed more explanation / naming examples for registering the driver
than what Paolo gave me, so I copied / adapted from "block/qcow2.c". The
parts I took as basis for modification are blamed on
commit 5efa9d5a8b
Author: Anthony Liguori <aliguori@us.ibm.com>
Date: Sat May 9 17:03:42 2009 -0500
Convert block infrastructure to use new module init functionality
commit 20d97356c9
Author: Blue Swirl <blauwirbel@gmail.com>
Date: Fri Apr 23 20:19:47 2010 +0000
Fix OpenBSD build
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
On 08/05/13 15:03, Paolo Bonzini wrote:
>
> [...]
>
> 4) There is another member, .create_options, which is an array of
> QEMUOptionParameter structs, terminated by an all-zero item. The only
> option you need is for the virtual disk size. You will find something
> to copy from in other block drivers, for example block/qcow2.c.
Code taken and adapted from "block/qcow2.c", as suggested. The code being
copied/modified is blamed on
commit 20d97356c9
Author: Blue Swirl <blauwirbel@gmail.com>
Date: Fri Apr 23 20:19:47 2010 +0000
Fix OpenBSD build
and
commit 7c80ab3f21
Author: Jes Sorensen <Jes.Sorensen@redhat.com>
Date: Fri Dec 17 16:02:39 2010 +0100
block/qcow2.c: rename qcow_ functions to qcow2_
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
On 08/05/13 15:03, Paolo Bonzini wrote:
>
> [...]
>
> 3) These members are special
>
> .format_name is the string "raw"
> .bdrv_open raw_open should set bs->sg to bs->file->sg and return 0
> .bdrv_close raw_close should do nothing
> .bdrv_probe raw_probe should just return 1.
v1->v2:
On 08/20/13 10:11, Kevin Wolf wrote:
> Am 16.08.2013 um 16:15 hat Laszlo Ersek geschrieben:
>> +static int raw_probe(void)
>> +{
>> + return 1;
>> +}
>
> Maybe add a comment here like "smallest possible positive score so that
> raw is used if and only if no other block driver works".
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
On 08/05/13 15:03, Paolo Bonzini wrote:
>
> [...]
>
> 2) This is also a simple forwarder function:
>
> .bdrv_create
>
> but there is no BlockDriverState argument so the forwarded-to function
> does not have a bs->file argument either. The forwarded-to function is
> bdrv_create_file.
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
On 08/05/13 15:03, Paolo Bonzini wrote:
>
> [...]
>
> 1) BlockDriver is a struct in which these function members are
> interesting:
>
> .bdrv_reopen_prepare
> .bdrv_co_readv
> .bdrv_co_writev
> .bdrv_co_is_allocated
> .bdrv_co_write_zeroes
> .bdrv_co_discard
> .bdrv_getlength
> .bdrv_get_info
> .bdrv_truncate
> .bdrv_is_inserted
> .bdrv_media_changed
> .bdrv_eject
> .bdrv_lock_medium
> .bdrv_ioctl
> .bdrv_aio_ioctl
> .bdrv_has_zero_init
>
> They should be implemented as simple forwarders (see above). There are
> 16 functions listed here, you can easily see how this already accounts
> for 100+ SLOC roughly...
>
> The implementations of bdrv_co_readv and bdrv_co_writev should also call
> BLKDBG_EVENT on bs->file too, before forwarding to bs->file. The events
> to be generated are BLKDBG_READ_AIO and BLKDBG_WRITE_AIO.
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
On 08/05/13 15:03, Paolo Bonzini wrote:
>
>
> ----- Original Message -----
>> From: "Laszlo Ersek" <lersek@redhat.com>
>> To: "Paolo Bonzini" <pbonzini@redhat.com>
>> Sent: Monday, August 5, 2013 2:43:46 PM
>> Subject: Re: [PATCH 1/2] raw: add license header
>>
>> On 08/02/13 00:27, Paolo Bonzini wrote:
>>> On 08/01/2013 10:13 AM, Christoph Hellwig wrote:
>>>> On Wed, Jul 31, 2013 at 08:19:51AM +0200, Paolo Bonzini wrote:
>>>>> Most of the block layer is under the BSD license, thus it is
>>>>> reasonable to license block/raw.c the same way. CCed people should
>>>>> ACK by replying with a Signed-off-by line.
>>>>
>>>> The coded was intended to be GPLv2.
>>>
>>> Laszlo, would you be willing to do clean-room reverse engineering?
>>>
>>> (No rants, please. :))
>>
>> What's the scope exactly?
>
> It's quite small, it's a file full of forwarders like
>
> static void raw_foo(BlockDriverState *bs)
> {
> return bdrv_foo(bs->file);
> }
>
> It's 170 lines of code, all as boring as this. I only picked you
> because I'm quite certain you have never seen the file (and the answer
> confirmed it).
>
> Basically:
>
> 1) BlockDriver is a struct in which these function members are
> interesting:
>
> .bdrv_reopen_prepare
> .bdrv_co_readv
> .bdrv_co_writev
> .bdrv_co_is_allocated
> .bdrv_co_write_zeroes
> .bdrv_co_discard
> .bdrv_getlength
> .bdrv_get_info
> .bdrv_truncate
> .bdrv_is_inserted
> .bdrv_media_changed
> .bdrv_eject
> .bdrv_lock_medium
> .bdrv_ioctl
> .bdrv_aio_ioctl
> .bdrv_has_zero_init
>
> They should be implemented as simple forwarders (see above).
> There are 16 functions listed here, you can easily see how this
> already accounts for 100+ SLOC roughly...
>
> The implementations of bdrv_co_readv and bdrv_co_writev should also
> call BLKDBG_EVENT on bs->file too, before forwarding to bs->file. The
> events to be generated are BLKDBG_READ_AIO and BLKDBG_WRITE_AIO.
>
> 2) This is also a simple forwarder function:
>
> .bdrv_create
>
> but there is no BlockDriverState argument so the forwarded-to function
> does not have a bs->file argument either. The forwarded-to function
> is bdrv_create_file.
>
> 3) These members are special
>
> .format_name is the string "raw"
> .bdrv_open raw_open should set bs->sg to bs->file->sg and return 0
> .bdrv_close raw_close should do nothing
> .bdrv_probe raw_probe should just return 1.
>
> 4) There is another member, .create_options, which is an array of
> QEMUOptionParameter structs, terminated by an all-zero item. The only
> option you need is for the virtual disk size. You will find something
> to copy from in other block drivers, for example block/qcow2.c.
>
> 5) Formats are registered with bdrv_register (takes a BlockDriver*).
> You also need to pass the caller of bdrv_register to block_init.
>
> 6) I'm not sure how to organize the patch series, so I'll leave this to
> your creativity. I guess in this case move/copy detection of git should
> be disabled. I would definitely include this spec in the commit
> message as a proof of clean-room reverse engineering.
>
> 7) Remember a BSD header like the one in block.c.
>
> Paolo
This patch implements the email up to the paragraph ending with "100+ SLOC
roughly". The skeleton is generated from the list there, with a simple
shell loop using "sed" and the raw_foo() template.
The BSD license block is copied (and reflowed) from
"util/qemu-progress.c".
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The expression "1LL << 63" tries to shift the 1 into the sign bit of a
'long long', which provokes a clang sanitizer warning:
runtime error: left shift of 1 by 63 places cannot be represented in type 'long long'
Use "1ULL << 63" as the definition of QCOW_OFLAG_COPIED instead
to avoid this. For consistency, we also update the other QCOW_OFLAG
definitions to use the ULL suffix rather than LL, though only the
shift by 63 is undefined behaviour.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
By the time that qemu 1.7 will be released, enough time will have passed
since qemu 1.1, which is the first version to understand version 3
images, that changing the default shouldn't hurt many people any more
and the benefits of using the new format outweigh the pain.
qemu-iotests already runs with compat=1.1 by default.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
The io_flush argument to qemu_aio_set_event_notifier() has been removed
since the block layer learnt to drain requests by itself. Fix the
Windows build for win32-aio.o by updating the
qemu_aio_set_event_notifier() call and dropping win32_aio_flush_cb().
Reviewed-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This is an autogenerated patch using scripts/switch-timer-api.
Switch the entire code base to using the new timer API.
Note this patch may introduce some line length issues.
Signed-off-by: Alex Bligh <alex@alex.org.uk>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Convert block_job_sleep_ns and co_sleep_ns to use the new timer
API.
Signed-off-by: Alex Bligh <alex@alex.org.uk>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
VMware ESX hosts also use different create and extent types for flat
files, respectively "vmfs" and "VMFS". This is not documented, but it
can be found at http://kb.vmware.com/kb/10002511 (Recreating a missing
virtual machine disk (VMDK) descriptor file).
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
VMware ESX hosts use a variant of the VMDK3 format, identified by the
vmfsSparse create type ad the VMFSSPARSE extent type.
It has 16 KB grain tables (L2) and a variable-size grain directory (L1).
In addition, the grain size is always 512, but that is not a problem
because it is included in the header.
The format of the extents is documented in the VMDK spec. The format
of the descriptor file is not documented precisely, but it can be
found at http://kb.vmware.com/kb/10026353 (Recreating a missing virtual
machine disk (VMDK) descriptor file for delta disks).
With these patches, vmfsSparse files only work if opened through the
descriptor file. Data files without descriptor files, as far as I
could understand, are not supported by ESX.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
--
v2: Rebase to patch 01.
Change le64_to_cpu to le32_to_cpu.
Rename vmdk_open_vmdk3 to vmdk_open_vmfs_sparse, which represents the
current usage of this format.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
VMDK3 header has the field l1dir_size, but vmdk_open_vmdk3 hardcoded the
value. This patch honors the header field.
And the L2 table size is 4096 according to VMDK spec[1], instead of
1 << 9 (512).
[1]:
http://www.vmware.com/support/developer/vddk/vmdk_50_technote.pdf?src=vmdk
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This header check is common to VMDK3 and VMDK4, so move it into
vmdk_add_extent().
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
In 4146b46c42e0989cb5842e04d88ab6ccb1713a48 (block: Produce zeros when
protocols reading beyond end of file), we break qemu-iotests ./check
-qcow2 022. This happens because qcow2 temporarily sets ->growable = 1
for vmstate accesses (which are stored beyond the end of regular image
data).
We introduce the bs->zero_beyond_eof to allow qcow2_load_vmstate() to
disable ->zero_beyond_eof temporarily in addition to enable ->growable.
[Since the broken patch "block: Produce zeros when protocols reading
beyond end of file" has not been merged yet, I have applied this fix
*first* and will then apply the next patch to keep the tree bisectable.
-- Stefan]
Suggested-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Asias He <asias@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
By the time that qemu 1.7 will be released, enough time will have passed
since qemu 1.1, which is the first version to understand version 3
images, that changing the default shouldn't hurt many people any more
and the benefits of using the new format outweigh the pain.
qemu-iotests already runs with compat=1.1 by default.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The .io_flush() handler no longer exists and has no users. Drop the
io_flush argument to aio_set_fd_handler() and related functions.
The AioFlushEventNotifierHandler and AioFlushHandler typedefs are no
longer used and are dropped too.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
.io_flush() is no longer called so drop qemu_rbd_aio_flush_cb().
qemu_aio_count is unused now so drop it too.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
.io_flush() is no longer called so drop nbd_have_request(). We cannot
drop in_flight since it is still used by other block/nbd.c code.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
.io_flush() is no longer called so drop qemu_laio_completion_cb(). It
turns out that count is now unused so drop that too.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Since .io_flush() is no longer called we do not need
qemu_gluster_aio_flush_cb() anymore. It turns out that qemu_aio_count
is unused now and can be dropped.
Thanks to Bharata B Rao <bharata@linux.vnet.ibm.com> for catching a
build failure with CONFIG_GLUSTERFS_DISCARD, which has been fixed.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
.io_flush() is no longer called so drop curl_aio_flush(). The acb[]
array that the function checks is still used in other parts of
block/curl.c. Therefore we cannot remove acb[], it is needed.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
If a block driver has no file descriptors to monitor but there are still
active requests, it can return 1 from .io_flush(). This is used to spin
during synchronous I/O.
Stop relying on .io_flush() and instead check
QLIST_EMPTY(&bs->tracked_requests) to decide whether there are active
requests.
This is the first step in removing .io_flush() so that event loops no
longer need to have the concept of synchronous I/O. Eventually we may
be able to kill synchronous I/O completely by running everything in a
coroutine, but that is future work.
Note this patch moves bs->throttled_reqs initialization to bdrv_new() so
that bdrv_requests_pending(bs) can safely access it. In practice bs is
g_malloc0() so the memory is already zeroed but it's safer to initialize
the queue properly.
We also need to fix up block/stream.c:close_unused_images() to prevent
traversing a dangling pointer while it rearranges the backing file
chain. This is necessary since the new bdrv_drain_all() traverses the
backing file chain.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Most of the block layer is under the BSD license, thus it is reasonable
to license block/raw.c the same way. CCed people should ACK by replying
with a Signed-off-by line.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Anthony Liguori <aliguori@us.ibm.com>
Cc: Markus Armbruster <armbru@redhat.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Cc: Luiz Capitulino <lcapitulino@redhat.com>
Cc: Jeff Cody <jcody@redhat.com>
Cc: Peter Lieven <pl@kamp.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Peter Lieven <pl@kamp.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Jeff Cody <jcody@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1375251592-2537-2-git-send-email-pbonzini@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
num_gtes_per_gte is a historical typo, rename it to a more sensible
name. It means "number of GrainTableEntries per GrainTable".
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We should never grow the stack beyond 1 MB, otherwise we'll fall off the
end. Thread stacks and coroutine stacks (1 MB) do not grow.
get_cluster_offset() allocates a big stack offset, it will fail for big
cluster images, change to heap allocated buffer.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
L1 table size is calculated from capacity, granularity and l2 table
size. If capacity is too big or later two are too small, the L1 table
will be too big to allocate in memory. Limit it to a reasonable range.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
header.num_gtes_per_gte determines size for L2 table. Check for too big
value before using it. Limit to 512M entries (2GB per one L2 table).
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Granularity is used to calculate the cluster size and allocate r/w
buffer. Check the value from image before using it, so we don't abort()
for unbounded memory allocation.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The size and offset fields are all non-negative values, use uint64_t for
them to avoid getting negative in memory value by int overflow.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
It's best to make it consistent that all on disk structures are
QEMU_PACKED.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Commit 3ac21627 changed the behaviour of bdrv_has_zero_init() to default
to 0. In the review for Sheepdog it turned out that enabling it is safe,
so that commit updated one BlockDriver definition of sheepdog to use
bdrv_has_zero_init_1, missed however that there are more BlockDrivers in
the driver. Fix these now.
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Liu Yuan <namei.unix@gmail.com>
Reviewed-by: MORITA Kazutaka <morita.kazutaka@lab.ntt.co.jp>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The comment was truncated. Add the missing parts, especially explain why
we need zero_dry_run.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The error on armv7hl was:
block/iscsi.c: In function ‘is_request_lun_aligned’:
block/iscsi.c:251:26: error: format ‘%ld’ expects argument of type ‘long int’, but argument 3 has type ‘int64_t’ [-Werror=format=]
iscsilun->block_size, sector_num, nb_sectors);
^
This also splits the long line to comply with qemu coding guidelines.
Signed-off-by: Richard W.M. Jones <rjones@redhat.com>
Reviewed-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
'dprintf' is the name of a POSIX standard function so we should not be
stealing it for our debug macro. Rename to 'DPRINTF' (in line with
a number of other source files.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: MORITA Kazutaka <morita.kazutaka@lab.ntt.co.jp>
Acked-by: Richard Henderson <rth@twiddle.net>
Acked-by: Kevin Wolf <kwolf@redhat.com>
Message-id: 1375100199-13934-2-git-send-email-peter.maydell@linaro.org
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
# By Stefan Hajnoczi (4) and others
# Via Stefan Hajnoczi
* stefanha/block:
dataplane: refuse to start if device is already in use
dataplane: enable virtio-blk x-data-plane=on live migration
migration: fix spice migration
migration: notify migration state before starting thread
block: Repair the throttling code.
gluster: Add image resize support
Message-id: 1375112172-24863-1-git-send-email-stefanha@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Implement .bdrv_truncate in GlusterFS block driver so that GlusterFS backend
can support image resizing.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Tested-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
All these typos were found by codespell.
sould -> should
emperical -> empirical
intialization -> initialization
successfuly -> successfully
gaurantee -> guarantee
Fix also another error (before before) in the same context.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
This patch adds sync-modes to the drive-backup interface and
implements the FULL, NONE and TOP modes of synchronization.
FULL performs as before copying the entire contents of the drive
while preserving the point-in-time using CoW.
NONE only copies new writes to the target drive.
TOP copies changes to the topmost drive image and preserves the
point-in-time using CoW.
For sync mode TOP are creating a new target image using the same backing
file as the original disk image. Then any new data that has been laid
on top of it since creation is copied in the main backup_run() loop.
There is an extra check in the 'TOP' case so that we don't bother to copy
all the data of the backing file as it already exists in the target.
This is where the bdrv_co_is_allocated() is used to determine if the
data exists in the topmost layer or below.
Also any new data being written is intercepted via the write_notifier
hook which ends up calling backup_do_cow() to copy old data out before
it gets overwritten.
For mode 'NONE' we create the new target image and only copy in the
original data from the disk image starting from the time the call was
made. This preserves the point in time data by only copying the parts
that are *going to change* to the target image. This way we can
reconstruct the final image by checking to see if the given block exists
in the new target image first, and if it does not, you can get it from
the original image. This is basically an optimization allowing you to
do point-in-time snapshots with low overhead vs the 'FULL' version.
Since there is no old data to copy out the loop in backup_run() for the
NONE case just calls qemu_coroutine_yield() which only wakes up after
an event (usually cancel in this case). The rest is handled by the
before_write notifier which again calls backup_do_cow() to write out
the old data so it can be preserved.
Signed-off-by: Ian Main <imain@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This is what QMP wants to use. The options haven't been enabled in any
release yet, so we're still free to change them.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
s->qcow and s->qcow_filename are allocated but not freed on error. Fix the
possible leaks, remove unnecessary check for bdrv_new(), propagate ret code of
bdrv_create() and also the one of enable_write_target().
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Implement bdrv_aio_discard for gluster.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
if the blocksize of an iSCSI LUN is bigger than the BDRV_SECTOR_SIZE
it is possible that sector_num or nb_sectors are not correctly
aligned.
to avoid corruption we fail requests which are misaligned.
Signed-off-by: Peter Lieven <pl@kamp.de>
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
this hask is not working (anymore). support for misaligned offsets should
be handled at the block layer.
Signed-off-by: Peter Lieven <pl@kamp.de>
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
the -ENOPSC case did not work due to the missing goto.
Reported-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Peter Lieven <pl@kamp.de>
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Don't assume that SG_IO is always invoked with a simple buffer,
check the iovec_count and if it is >= 1 then we need to pass an array
of iovectors to libiscsi instead of just a plain buffer.
Signed-off-by: Ronnie Sahlberg <ronniesahlberg@gmail.com>
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
One of the major reasons for doing something new for -blockdev and
blockdev-add was that the old block layer code parses filenames instead
of just taking them literally. So we should really leave it untouched
when it's passing using the new interfaces (like -drive
file.filename=...).
This allows opening relative file names that contain a colon.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
CURL driver requests partial data from server on guest IO req. For HTTP
and HTTPS, it uses "Range: ***" in requests, and this will not work if
server not accepting range. This patch does this check when open.
* Removed curl_size_cb, which is not used: On one hand it's registered to
libcurl as CURLOPT_WRITEFUNCTION, instead of CURLOPT_HEADERFUNCTION,
which will get called with *data*, not *header*. On the other hand the
s->len is assigned unconditionally later.
In this gone function, the sscanf for "Content-Length: %zd", on
(void *)ptr, which is not guaranteed to be zero-terminated, is
potentially a security bug. So this patch fixes it as a side-effect. The
bug is reported as: https://bugs.launchpad.net/qemu/+bug/1188943
(Note the bug is marked "private" so you might not be able to see it)
* Introduced curl_header_cb, which is used to parse header and mark the
server as accepting range if "Accept-Ranges: bytes" line is seen from
response header. If protocol is HTTP or HTTPS, but server response has
no not this support, refuse to open this URL.
Note that python builtin module SimpleHTTPServer is an example of not
supporting range, if you need to test this driver, get a better server
or use internet URLs.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Depending on the subformat, has_zero_init queries underlying storage for
flat extent. If it has a flat extent and its underlying storage doesn't
have zero init, return 0. Otherwise return 1.
Aligns the operator assignments.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
.has_zero_init defaults to 1 for all formats and protocols.
this is a dangerous default since this means that all
new added drivers need to manually overwrite it to 0 if
they do not ensure that a device is zero initialized
after bdrv_create().
if a driver needs to explicitly set this value to
1 its easier to verify the correctness in the review process.
during review of the existing drivers it turned out
that ssh and gluster had a wrong default of 1.
both protocols support host_devices as backend
which are not by default zero initialized. this
wrong assumption will lead to possible corruption
if qemu-img convert is used to write to such a backend.
vpc and vmdk also defaulted to 1 altough they support
fixed respectively flat extends. this has to be addresses
in separate patches. both formats as well as the mentioned
ssh and gluster are turned to the default of 0 with this
patch for safety.
a similar problem with the wrong default existed for
iscsi most likely because the driver developer did
oversee the default value of 1.
Signed-off-by: Peter Lieven <pl@kamp.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Depending on the subformat, has_zero_init on VHD must behave like raw
and query the underlying storage (fixed) or like other sparse formats
that can always return 1 (dynamic, differencing).
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
When creating image with backing file, the driver tries to calculate the
relative path from created image file to backing file, but the path
computation is incorrect. e.g.:
$ qemu-img create -f vmdk -b vmdk-data-disk.vmdk vmdk-data-snapshot1
Formatting 'vmdk-data-snapshot1', fmt=vmdk size=10737418240
backing_file='vmdk-data-disk.vmdk' compat6=off zeroed_grain=off
$ qemu-img info vmdk-data-snapshot1
image: vmdk-data-snapshot1
file format: vmdk
virtual size: 10G (10737418240 bytes)
disk size: 12K
-> backing file: disk.vmdk
The common part in file names, "vmdk-data-", is incorrectly forgotten by
relative_path(). As the VMDK specification has no restriction on
parentNameHint to be relative path, we simply remove this by using the
backing_file option.
Cc: qemu-stable@nongnu.org
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
GlusterFS volumes can be backed by block devices, in which case
bdrv_create() doesn't make sure that the image is zeroed out. It is
currently not possibly to detect whether a given image is backed by a
file or a block device, and incorrectly assuming that it is zeroed
corrupts images during qemu-img convert, so let's err on the side of
caution and always return 0.
Cc: qemu-stable@nongnu.org
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
If the remote is a regular file, set it to true (ie. reads of
uninitialized areas in a newly created file will return zeroes).
If we can't prove that, return false (a safe default).
Tested by adding a debugging print statement [not part of this commit]
and creating a remote file and a remote block device:
$ ./qemu-img create ssh://localhost/tmp/new 100M
Formatting 'ssh://localhost/tmp/new', fmt=raw size=104857600
filename ssh://localhost/tmp/new: has_zero_init = 1
$ sudo lvcreate -L 1G -n tmp /dev/fedora
Logical volume "tmp" created
$ ./qemu-img create ssh://localhost/dev/fedora/tmp 1G
Formatting 'ssh://localhost/dev/fedora/tmp', fmt=raw size=1073741824
filename ssh://localhost/dev/fedora/tmp: has_zero_init = 0
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: qemu-stable@nongnu.org
Signed-off-by: Richard W.M. Jones <rjones@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
backup_start() creates a block job that copies a point-in-time snapshot
of a block device to a target block device.
We call backup_do_cow() for each write during backup. That function
reads the original data from the block device before it gets
overwritten. The data is then written to the target device.
Currently backup cluster size is hardcoded to 65536 bytes.
[I made a number of changes to Dietmar's original patch and folded them
in to make code review easy. Here is the full list:
* Drop BackupDumpFunc interface in favor of a target block device
* Detect zero clusters with buffer_is_zero() and use bdrv_co_write_zeroes()
* Use 0 delay instead of 1us, like other block jobs
* Unify creation/start functions into backup_start()
* Simplify cleanup, free bitmap in backup_run() instead of cb
* function
* Use HBitmap to avoid duplicating bitmap code
* Use bdrv_getlength() instead of accessing ->total_sectors
* directly
* Delete the backup.h header file, it is no longer necessary
* Move ./backup.c to block/backup.c
* Remove #ifdefed out code
* Coding style and whitespace cleanups
* Use bdrv_add_before_write_notifier() instead of blockjob-specific hooks
* Keep our own in-flight CowRequest list instead of using block.c
tracked requests. This means a little code duplication but is much
simpler than trying to share the tracked requests list and use the
backup block size.
* Add on_source_error and on_target_error error handling.
* Use trace events instead of DPRINTF()
-- stefanha]
Signed-off-by: Dietmar Maurer <dietmar@proxmox.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The raw-posix driver has code to provide a /dev/cdrom on OS X even
though it doesn't really exist. However, since commit c66a6157 the real
filename is dismissed after finding it, so opening /dev/cdrom fails.
Put the filename back into the options QDict to make this work again.
Cc: qemu-stable@nongnu.org
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Refuse to open higher version for safety.
Although we try to be compatible with published VMDK spec, VMware has
newer version from ESXi 5.1 exported OVF/OVA, which we have no knowledge
what's changed in it. And it is very likely to have more new versions in
the future, so it's not safe to open them blindly.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This optimises the discard operation for freed clusters by batching
discard requests (both snapshot deletion and bdrv_discard end up
updating the refcounts cluster by cluster).
Note that we don't discard asynchronously, but keep s->lock held. This
is to avoid that a freed cluster is reallocated and written to while the
discard is still in flight.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Deleted snapshots are discarded in the image file by default, discard
requests take their default from the -drive discard=... option and other
places that free clusters must always be enabled explicitly.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This adds a refcount update reason to all callers of update_refcounts(),
so that a follow-up patch can use this information to decide whether
clusters that reach a refcount of 0 should be discarded in the image
file.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
# By Paolo Bonzini (3) and others
# Via Paolo Bonzini
* bonzini/scsi-next:
iscsi: reorganize iscsi_readcapacity_sync
iscsi: simplify freeing of tasks
vhost-scsi: fix k->set_guest_notifiers() NULL dereference
scsi-disk: scsi-block device for scsi pass-through should not be removable
scsi-generic: check the return value of bdrv_aio_ioctl in execute_command
scsi-generic: fix sign extension of READ CAPACITY(10) data
scsi: reset cdrom tray statuses on scsi_disk_reset
Message-id: 1371565016-2643-1-git-send-email-pbonzini@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Avoid the goto, and use the same retry logic for the 10- and 16-
byte versions.
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Always free them in the iscsi_aio_*_acb functions and remove the
checks in their callers. Remove ifs when the task struct was
previously dereferenced (spotted by Coverity).
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Otherwise they would get passed to getaddrinfo and fail with:
address resolution failed for [::1]🔢 Name or service not known
(Broken by commit v1.4.0-736-gf17c90b)
Signed-off-by: Ján Tomko <jtomko@redhat.com>
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
# By Luiz Capitulino
# Via Luiz Capitulino
* luiz/queue/qmp:
qerror: drop QERR_OPEN_FILE_FAILED macro
block: bdrv_reopen_prepare(): don't use QERR_OPEN_FILE_FAILED
savevm: qmp_xen_save_devices_state(): use error_setg_file_open()
dump: qmp_dump_guest_memory(): use error_setg_file_open()
cpus: use error_setg_file_open()
blockdev: use error_setg_file_open()
block: mirror_complete(): use error_setg_file_open()
rng-random: use error_setg_file_open()
error: add error_setg_file_open() helper
Message-id: 1371484631-29510-1-git-send-email-lcapitulino@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
the hard-coded 2k buffer on the stack won't allow reading big descriptor
files which can be generated when storing big images. For example 500G
vmdk splitted to 2G chunks.
Signed-off-by: Evgeny Budilovsky <evgeny.budilovsky@ravellosystems.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
(Found by Kamil Dudka)
Signed-off-by: Richard W.M. Jones <rjones@redhat.com>
Cc: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Remember to byteswap VMDK4Header.desc_offset on big-endian machines.
Cc: qemu-stable@nongnu.org
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Just call sd_create_branch() in the snapshot_goto to rollback the image is good
enough. With this patch, 'loadvm' process for sheepdog is modified:
Suppose we have a snapshot chain A --> B --> C, we do 'loadvm A' so as to get
a new chain,
A --> B
|
V
C1
in the old code:
1 reload inode of A (in snapshot_goto)
2 read vmstate via A's vdi_id (loadvm_state)
3 delete C and create C1, reload inode of C1 (sd_create_branch on write)
with this patch applied:
1 reload inode of A, delete C and create C1 (in snapshot_goto)
2 read vmstate via C1's parent, that is A's vdi_id (loadvm_state)
This will fix the possible bug that QEMU exit between 2 and 3 in the old code
Cc: qemu-devel@nongnu.org
Cc: MORITA Kazutaka <morita.kazutaka@lab.ntt.co.jp>
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Liu Yuan <namei.unix@gmail.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This is an old and obvious bug. We should pass snapshot_id to the
tag. Or simple command like 'qemu-img snapshot -a tag sheepdog:image' will fail
Cc: qemu-devel@nongnu.org
Cc: MORITA Kazutaka <morita.kazutaka@lab.ntt.co.jp>
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Liu Yuan <namei.unix@gmail.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Now image info will be retrieved as an embbed json object inside
BlockDeviceInfo, backing chain info and all related internal snapshot
info can be got in the enhanced recursive structure of ImageInfo. New
recursive member *backing-image is added to reflect the backing chain
status.
Signed-off-by: Wenchao Xia <xiawenc@linux.vnet.ibm.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This patch adds function bdrv_query_image_info(), which will
retrieve image info in qmp object format. The implementation is
based on the code moved from qemu-img.c, but uses block layer
function to get snapshot info.
Signed-off-by: Wenchao Xia <xiawenc@linux.vnet.ibm.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This patch adds function bdrv_query_snapshot_info_list(), which will
retrieve snapshot info of an image in qmp object format. The implementation
is based on the code moved from qemu-img.c with modification to fit more
for qmp based block layer API.
Signed-off-by: Wenchao Xia <xiawenc@linux.vnet.ibm.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
bdrv_snapshot_dump() and bdrv_image_info_dump() do not dump to a buffer now,
some internal buffers are still used for format control, which have no
chance to be truncated. As a result, these two functions have no more issue
of truncation, and they can be used by both qemu and qemu-img with correct
parameter specified.
Signed-off-by: Wenchao Xia <xiawenc@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This patch is a pure code move patch, except following modification:
1 get_human_readable_size() is changed to static function.
2 dump_human_image_info() is renamed to bdrv_image_info_dump().
3 in qmp_query_block() and qmp_query_blockstats, use bdrv_next(bs)
instead of direct traverse of global array 'bdrv_states'.
4 collect_snapshots() and collect_image_info() are renamed, unused parameter
*fmt in collect_image_info() is removed.
5 code style fix.
To avoid conflict and tip better, macro in header file is BLOCK_QAPI_H
instead of QAPI_H. Now block.h and snapshot.h are at the same level in
include path, block_int.h and qapi.h will both include them.
Signed-off-by: Wenchao Xia <xiawenc@linux.vnet.ibm.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
All snapshot related code, except bdrv_snapshot_dump() and
bdrv_is_snapshot(), is moved to block/snapshot.c. bdrv_snapshot_dump()
will be moved to another file later. bdrv_is_snapshot() is not related
with internal snapshot. It also fixes small code style errors reported
by check script.
Signed-off-by: Wenchao Xia <xiawenc@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This patch is used to remove twice include of "qemu-common.h" in
block/win32-aio.c
Signed-off-by: Qiao Nuohan <qiaonuohan@cn.fujitsu.com>
Reviewed-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
This catches the situation that is described in the bug report at
https://bugs.launchpad.net/qemu/+bug/865518 and goes like this:
$ qemu-img create -f qcow2 huge.qcow2 $((1024*1024))T
Formatting 'huge.qcow2', fmt=qcow2 size=1152921504606846976 encryption=off cluster_size=65536 lazy_refcounts=off
$ qemu-io /tmp/huge.qcow2 -c "write $((1024*1024*1024*1024*1024*1024 - 1024)) 512"
Segmentation fault
With this patch applied the segfault will be avoided, however the case
will still fail, though gracefully:
$ qemu-img create -f qcow2 /tmp/huge.qcow2 $((1024*1024))T
Formatting 'huge.qcow2', fmt=qcow2 size=1152921504606846976 encryption=off cluster_size=65536 lazy_refcounts=off
qemu-img: The image size is too large for file format 'qcow2'
Note that even long before these overflow checks kick in, you get
insanely high memory usage (up to INT_MAX * sizeof(uint64_t) = 16 GB for
the L1 table), so with somewhat smaller image sizes you'll probably see
qemu aborting for a failed g_malloc().
If you need huge image sizes, you should increase the cluster size to
the maximum of 2 MB in order to get higher limits.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Use special offset to write zeroes efficiently, when zeroed-grain GTE is
available. If zero-write an allocated cluster, cluster is leaked because
its offset pointer is overwritten by "0x1".
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Previously VmdkMetaData.offset is stored little endian while other
fields are cpu endian. This changes offset to cpu endian and convert
before writing to image.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Add image create option "zeroed-grain" to enable zeroed-grain GTE
feature of vmdk sparse extents. When this option is on, header version
of newly created extent will be 2 and VMDK4_FLAG_ZERO_GRAIN flag bit
will be set.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Introduced support for zeroed-grain GTE, as specified in Virtual Disk
Format 5.0[1].
Recent VMware hosted platform products support a new “zeroed‐grain”
grain table entry (GTE). The zeroed‐grain GTE returns all zeros on
read. In other words, the zeroed‐grain GTE indicates that a grain
in the child disk is zero‐filled but does not actually occupy space
in storage. A sparse extent with zeroed‐grain GTE has the following
in its header:
* SparseExtentHeader.version = 2
* SparseExtentHeader.flags has bit 2 set
Other than the new flag and the possibly zeroed‐grain GTE, version 2
sparse extents are identical to version 1. Also, a zeroed‐grain GTE
has value 0x1 in the GT table.
[1] Virtual Disk Format 5.0, http://www.vmware.com/support/developer/vddk/vmdk_50_technote.pdf?src=vmdk
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Internal routines in vmdk.c previously return -1 on error and 0 on
success. More return values are useful for future changes such as
zeroed-grain GTE. Change all the magic `return 0` and `return -1` to
macro names:
* VMDK_OK 0
* VMDK_ERROR (-1)
* VMDK_UNALLOC (-2)
* VMDK_ZEROED (-3)
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This adds in read-only support to the VHDX image format. This supports
reads for fixed-size, and dynamic sized VHDX images.
Differencing files are still unsupported.
The image must be opened without BDRV_O_RDWR set, because we do not
yet update the headers. I.e., pass 'readonly=on' in the drive image
options from the QEMU commandline.
Signed-off-by: Jeff Cody <jcody@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This is the initial block driver framework for VHDX image support
(i.e. Hyper-V image file formats), that supports opening VHDX files, and
parsing the headers.
This commit does not yet enable:
- reading
- writing
- updating the header
- differencing files (images with parents)
- log replay / dirty logs (only clean images)
This is based on Microsoft's VHDX specification:
"VHDX Format Specification v0.95", published 4/12/2012
https://www.microsoft.com/en-us/download/details.aspx?id=29681
Signed-off-by: Jeff Cody <jcody@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This is based on Microsoft's VHDX specification:
"VHDX Format Specification v0.95", published 4/12/2012
https://www.microsoft.com/en-us/download/details.aspx?id=29681
These structures define the various header, metadata, and other
block structures defined in the VHDX specification.
Signed-off-by: Jeff Cody <jcody@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Currently the 'loadvm' opertaion works as following:
1. switch to the snapshot
2. mark current working VDI as a snapshot
3. rely on sd_create_branch to create a new working VDI based on the snapshot
This works not the same as other format as QCOW2. For e.g,
qemu > savevm # get a live snapshot snap1
qemu > savevm # snap2
qemu > loadvm 1 # This will steally create snap3 of the working VDI
Which will result in following snapshot chain:
base <-- snap1 <-- snap2 <-- snap3
^
|
working VDI
snap3 was unnecessarily created and might be annoying users.
This patch discard the unnecessary 'snap3' creation. and implement
rollback(loadvm) operation to the specified snapshot by
1. switch to the snapshot
2. delete working VDI
3. rely on sd_create_branch to create a new working VDI based on the snapshot
The snapshot chain for above example will be:
base <-- snap1 <-- snap2
^
|
working VDI
Cc: qemu-devel@nongnu.org
Cc: MORITA Kazutaka <morita.kazutaka@lab.ntt.co.jp>
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Liu Yuan <tailai.ly@taobao.com>
Reviewed-by: MORITA Kazutaka <morita.kazutaka@lab.ntt.co.jp>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
When a snapshot is taken from out side of qemu (e.g. qemu-img
snapshot), write requests to the current vdi return SD_RES_READONLY.
In this case, the sheepdog block driver needs to update the current
inode to the latest one and resend the write requests.
Signed-off-by: MORITA Kazutaka <morita.kazutaka@lab.ntt.co.jp>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This adds a helper function to update the current inode state with the
specified vdi object.
Signed-off-by: MORITA Kazutaka <morita.kazutaka@lab.ntt.co.jp>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Sheepdog returns SD_RES_READONLY when qemu sends write requests to the
snapshot vdi. This adds the result code and makes sd_strerror() print
its error reason.
Signed-off-by: MORITA Kazutaka <morita.kazutaka@lab.ntt.co.jp>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This makes 'filename' and 'tag' constant variables, and renames
'for_snapshot' to 'lock' to clear how it works.
Signed-off-by: MORITA Kazutaka <morita.kazutaka@lab.ntt.co.jp>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Commit a9ccedc3 frees the QemuOpts for the driver-specific options
immediately, even though it still needs the filename string that is
contained there. This doesn't work. Move the deletion of the QemuOpts to
the end of the function where its content isn't needed any more.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Cc: MORITA Kazutaka <morita.kazutaka@lab.ntt.co.jp>
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Liu Yuan <tailai.ly@taobao.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Cc: MORITA Kazutaka <morita.kazutaka@lab.ntt.co.jp>
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Liu Yuan <tailai.ly@taobao.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The 'TRIM' command from VM that is to release underlying data storage for
better thin-provision is already supported by the Sheepdog.
This patch adds the TRIM support at QEMU part.
For older Sheepdog that doesn't support it, we return 0(success) to upper layer.
Cc: MORITA Kazutaka <morita.kazutaka@lab.ntt.co.jp>
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Liu Yuan <tailai.ly@taobao.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
# By Kevin Wolf (16) and Stefan Hajnoczi (4)
# Via Kevin Wolf
* kwolf/for-anthony:
qemu-iotests: add 053 unaligned compressed image size test
block: Allow overriding backing.file.filename
block: Remove filename parameter from .bdrv_file_open()
vvfat: Use bdrv_open options instead of filename
sheepdog: Use bdrv_open options instead of filename
rbd: Use bdrv_open options instead of filename
iscsi: Use bdrv_open options instead of filename
gluster: Use bdrv_open options instead of filename
curl: Use bdrv_open options instead of filename
blkverify: Use bdrv_open options instead of filename
blkdebug: Use bdrv_open options instead of filename
raw-win32: Use bdrv_open options instead of filename
raw-posix: Use bdrv_open options instead of filename
block: Enable filename option
block: Add driver-specific options for backing files
block: Fail gracefully when using a format driver on protocol level
qemu-iotests: Fix _filter_qemu
qemu-img: do not zero-pad the compressed write buffer
qcow: allow sub-cluster compressed write to last cluster
qcow2: allow sub-cluster compressed write to last cluster
Message-id: 1366630294-18984-1-git-send-email-kwolf@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
# By Stefan Hajnoczi
# Via Paolo Bonzini
* bonzini/nbd-next:
nbd: set TCP_NODELAY
nbd: use TCP_CORK in nbd_co_send_request()
nbd: unlock mutex in nbd_co_send_request() error path
Message-id: 1366381830-11267-1-git-send-email-pbonzini@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This is only to convert the internal interface that is used for passing
the "filename" to be parsed, but converting to actual fine grained
options is left for another day, as it doesn't look trivial.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
This is only to convert the internal interface that is used for passing
the "filename" to be parsed, but converting to actual fine grained
options is left for another day, as it doesn't look trivial.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
This is only to convert the internal interface that is used for passing
the "filename" to be parsed, but converting to actual fine grained
options is left for another day, as it doesn't look trivial.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
This is only to convert the internal interface that is used for passing
the "filename" to be parsed, but converting to actual fine grained
options is left for another day, as it doesn't look trivial.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
As a bonus, going through the QemuOpts QEMU_OPT_SIZE parser for the
readahead option gives us proper error reporting that the previous use
of atoi() lacked.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Options starting in "backing." are passed to the backing file now. If
you don't need to specify the filename for the backing file, you can add
it on the command line instead of in the image file:
$ qemu-nbd -t /tmp/test.img
$ qemu-img create -f qcow2 empty.qcow2 1G
$ qemu-system-x86_64 -drive file=empty.qcow2,backing.file.driver=nbd,\
backing.file.host=localhost
Note that this doesn't override the backing filename from the image. If
the image has one, this will fail because NBD doesn't want the options
and a filename at the same time.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Compression in qcow requires image length to be a multiple of the
cluster size. Lift this requirement by zero-padding the final cluster
when necessary. The virtual disk size is still not cluster-aligned, so
the guest cannot access the zero sectors.
Note that this is almost identical to the qcow2 version of this code.
qcow2's compression code is drawn from qcow.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Compression in qcow2 requires image length to be a multiple of the
cluster size. Lift this requirement by zero-padding the final cluster
when necessary. The virtual disk size is still not cluster-aligned, so
the guest cannot access the zero sectors.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Now gcc will check whether format string and variable arguments match.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Disable the Nagle algorithm to reduce latency. Note this means we must
also use TCP_CORK when sending header followed by payload to avoid
fragmenting lots of little packets. The previous patch took care of
that.
Suggested-by: Nick Thomas <nick@bytemark.co.uk>
Tested-by: Nick Thomas <nick@bytemark.co.uk>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use TCP_CORK to defer packet transmission until both the header and the
payload have been written.
Suggested-by: Nick Thomas <nick@bytemark.co.uk>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The existing bdrv_co_flush_to_disk implementation uses rbd_flush(),
which is sychronous and causes the main qemu thread to block until it
is complete. This results in unresponsiveness and extra latency for
the guest.
Fix this by using an asynchronous version of flush. This was added to
librbd with a special #define to indicate its presence, since it will
be backported to stable versions. Thus, there is no need to check the
version of librbd.
Implement this as bdrv_aio_flush, since it matches other aio functions
in the rbd block driver, and leave out bdrv_co_flush_to_disk when the
asynchronous version is available.
Reported-by: Oliver Francke <oliver@filoo.de>
Signed-off-by: Josh Durgin <josh.durgin@inktank.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
libssh2_sftp_fsync is an extension to libssh2 to support fsync(2) over
sftp, which is itself an extension of OpenSSH.
If both libssh2 and the ssh daemon support it, this will allow
bdrv_flush_to_disk to commit changes through to disk on the remote
server.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
qemu-system-x86_64 -drive file=ssh://hostname/some/image
QEMU will ssh into 'hostname' and open '/some/image' which is made
available as a standard block device.
You can specify a username (ssh://user@host/...) and/or a port number
(ssh://host:port/...). You can also use an alternate syntax using
properties (file.user, file.host, file.port, file.path).
Current limitations:
- Authentication must be done without passwords or passphrases, using
ssh-agent. Other authentication methods are not supported.
- Uses a single connection, instead of concurrent AIO with multiple
SSH connections.
This is implemented using libssh2 on the client side. The server just
requires a regular ssh daemon with sftp-server support. Most ssh
daemons on Unix/Linux systems will work out of the box.
Signed-off-by: Richard W.M. Jones <rjones@redhat.com>
Cc: Stefan Hajnoczi <stefanha@gmail.com>
Cc: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Directly pass the QEMUIOVector on instead of linearising it.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Move aes.h from include/block to include/qemu to show it can be reused
by other subsystems.
Cc: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Many of these should be cleaned up with proper qdev-/QOM-ification.
Right now there are many catch-all headers in include/hw/ARCH depending
on cpu.h, and this makes it necessary to compile these files per-target.
However, fixing this does not belong in these patches.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It ignored the error code, and at least the 'goto fail' is obvious
nonsense as it creates an endless loop (if the next attempt doesn't
magically succeed) and leaves the in-memory L1 table in big-endian
instead of converting it back.
In error cases, there's no point in writing an updated L1 table, so
skip this part for them.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The fcntl(fd, F_SETFL, O_NONBLOCK) flag is not specific to sockets.
Rename to qemu_set_nonblock() just like qemu_set_cloexec().
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Instead of just checking once in exactly this order if there are
dependendies, non-COW clusters and new allocation, this starts looping
around these. This way we can, for example, gather non-COW clusters after
new allocations as long as the host cluster offsets stay contiguous.
Once handle_dependencies() is extended so that COW areas of in-flight
allocations can be overwritten, this allows to continue with gathering
other clusters (we wouldn't be able to do that without this change
because we would have missed a possible second dependency in one of the
next clusters).
This means that in the typical sequential write case, we can combine the
COW overwrite of one cluster with the allocation of the next cluster as
soon as something like Delayed COW gets actually implemented. It is only
by avoiding splitting requests this way that Delayed COW actually starts
improving performance noticably.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This patch is mainly to separate the indentation change from the
semantic changes. All that really changes here is that everything moves
into a while loop, all 'goto done' become 'break' and at the end of the
loop a new 'break is inserted.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Instead of expecting a single l2meta, have a list of them. This allows
to still have a single I/O request for the guest data, even though
multiple l2meta may be needed in order to describe both a COW overwrite
and a new cluster allocation (typical sequential write case).
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This gets rid of the nb_clusters and keep_clusters and the associated
complicated calculations. Just advance the number of bytes that have
been processed and everything is fine.
This patch advances the variables even after the last operation even
though they aren't used any more afterwards to make things look more
uniform. A later patch will turn the whole thing into a loop and then
it actually starts making sense.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This makes handle_alloc() and handle_copied() return byte-granularity
host offsets instead of returning always the cluster start. This is
required so that qcow2_alloc_cluster_offset() can stop aligning
everything to cluster boundaries.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Look only for clusters that start at a given physical offset.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Now *bytes is used to return the length of the area that can be written
to without performing an allocation or COW.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
handle_copied() uses its bytes parameter now to determine how many
clusters it should try to find.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Things can be simplified a bit now. No semantic changes.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The interface works completely on a byte granularity now and duplicated
parameters are removed.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
handle_alloc() is now called with the offset at which the actual new
allocation starts instead of the offset at which the whole write request
starts, part of which may already be processed.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
We already communicate the same information in *bytes.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This moves some code that prepares the allocation of new clusters to
where the actual allocation happens. This is the minimum required to be
able to move it to a separate function in the next patch.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This is a more precise description of what really constitutes a
dependency. The behaviour doesn't change at this point because the COW
area of the old request is still aligned to cluster boundaries and
therefore an overlap is detected wheneven the requests touch any part of
the same cluster.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The old code detected an overlapping allocation even when the
allocations didn't actually overlap, but were only adjacent.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Handling overlapping allocations isn't just a detail of cluster
allocation. It is rather one of three ways to get the host cluster
offset for a write request:
1. If a request overlaps an in-flight allocations, the cluster offset
can be taken from there (this is what handle_dependencies will evolve
into) or the request must just wait until the allocation has
completed. Accessing the L2 is not valid in this case, it has
outdated information.
2. Outside overlapping areas, check the clusters that can be written to
as they are, with no COW involved.
3. If a COW is required, allocate new clusters
Changing the code to reflect this doesn't change the behaviour because
overlaps cannot exist for clusters that are kept in step 2. It does
however make it easier for later patches to work on clusters that belong
to an allocation that is still in flight.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The unlock wakes up the next coroutine, but the currently running
coroutine will lock it again before it yields, so this doesn't make a
lot of sense.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This should be based on the virtual disk size, not on the size of the
image.
Interesting observation: With some VM state stored in the image file,
percentages higher than 100% are possible, even though snapshots
themselves are ignored. This is a qcow2 bug to be fixed another day: The
VM state should be discarded in the active L2 tables after completing
the snapshot creation.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The new parameter is unused yet.
This part was missing in commit 787e4a8500.
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Eric Blake <eblake@redhat.com>
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Commit 787e4a85 [block: Add options QDict to bdrv_file_open() prototypes] didn't
update rbd.c accordingly.
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Liu Yuan <tailai.ly@taobao.com>
Reviewed-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
A file name may only specified if no host or socket path is specified.
The latter two may not appear at the same time either.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
The URL method already takes care to apply the default port when none is
specfied. Directly specifying driver-specific options required the port
number until now. Allow leaving it out and apply the default.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
In order to achieve this, the .bdrv_probe callbacks of all drivers must
cope with this. The DMG driver is the only one that bases its decision
on the filename and it needs to be changed.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
If a driver needs structured data and not just a string, it can provide
a .bdrv_parse_filename callback now that parses the command line string
into separate options. Keeping this separate from .bdrv_open_filename
ensures that the preferred way of directly specifying the options always
works as well if parsing the string works.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
The existing parsers for the file name now parse everything into the
bdrv_open() options QDict. Instead of using these parsers, you can now
directly specify the options on the command line, like this:
qemu-system-x86_64 -drive file=nbd:,file.port=1234,file.host=::1
Clearly the file=... part could use further improvement, but it's a
start.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
The NBD block supports an URL syntax, for which a URL parser returns
separate hostname and port fields. It also supports the traditional qemu
syntax encoded in a filename. Until now, after parsing the URL to get
each piece of information, a new string is built to be fed to socket
functions.
Instead of building a string in the URL case that is immediately parsed
again, parse the string in both cases and use the QemuOpts interface to
qemu-sockets.c.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Need to pass an options QDict to qcow2_open() now. This fixes a segfault
on the migration target with qcow2.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Sheepdog (neither quorum nor unsafe mode) will refuse to serve IO requests when
number of alive nodes is less than that of copies specified by users. This will
return 0x19 to QEMU client which currently doesn't recognize it.
This patch adds an error description when QEMU client receives it, other than
plainly printing 'Invalid error code'
Cc: MORITA Kazutaka <morita.kazutaka@lab.ntt.co.jp>
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Liu Yuan <tailai.ly@taobao.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: MORITA Kazutaka <morita.kazutaka@lab.ntt.co.jp>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Now that each AioContext has a ThreadPool and the main loop AioContext
can be fetched with bdrv_get_aio_context(), we can eliminate the concept
of a global thread pool from thread-pool.c.
The submit functions must take a ThreadPool* argument.
block/raw-posix.c and block/raw-win32.c use
aio_get_thread_pool(bdrv_get_aio_context(bs)) to fetch the main loop's
ThreadPool.
tests/test-thread-pool.c must be updated to reflect the new
thread_pool_submit() function prototypes.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
If an io_flush handler is not set, qemu_aio_wait doesn't invoke
callbacks.
Signed-off-by: MORITA Kazutaka <morita.kazutaka@lab.ntt.co.jp>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Using a blocking socket in the coroutine context reduces the chance of
switching to other work. This patch makes the sheepdog driver use a
non-blocking fd always.
Signed-off-by: MORITA Kazutaka <morita.kazutaka@lab.ntt.co.jp>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Otherwise, live migration of the top layer will miss zero clusters and
let the backing file show through. This also matches what is done in qed.
QCOW2_CLUSTER_ZERO clusters are invalid in v2 image files. Check this
directly in qcow2_get_cluster_offset instead of replicating the test
everywhere.
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
We already flush when the function completes. There is no need to flush
after every compressed cluster.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The update_cluster_refcount() function increments/decrements a cluster's
refcount and then returns the new refcount value.
There is no need to flush since both update_cluster_refcount() callers
already take care of this:
1. qcow2_alloc_bytes() calls update_cluster_refcount() when compressed
sectors will be appended to an existing cluster with enough free
space. qcow2_alloc_bytes() already flushes so there is no need to do
so in update_cluster_refcount().
2. qcow2_update_snapshot_refcount() sets a cache dependency on refcounts
if it needs to update L2 entries. It also flushes before completing.
Removing this flush significantly speeds up qcow2 snapshot creation:
$ qemu-img create -f qcow2 test.qcow2 -o size=50G,preallocation=metadata
$ time qemu-img snapshot -c new test.qcow2
Time drops from more than 3 minutes to under 1 second.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Users of qcow2_update_snapshot_refcount() do not flush consistently.
qcow2_snapshot_create() flushes but qcow2_snapshot_goto() and
qcow2_snapshot_delete() do not.
Solve this by moving the bdrv_flush() into
qcow2_update_snapshot_refcount().
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Compressed writes use qcow2_alloc_bytes() to allocate space with byte
granularity. The affected clusters' refcounts will be incremented but
we do not need to flush yet.
Set a L2 cache dependency on the refcount block cache, so that the
refcounts get written out before the L2 updates.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Since qcow2 metadata is cached we need to flush the caches, not just the
underlying file. Use bdrv_flush(bs) instead of bdrv_flush(bs->file).
Also add the error return path when bdrv_flush() fails and move the
flush after checking for qcow2_alloc_clusters() failure so that the
qcow2_alloc_clusters() error return value takes precedence.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
update_refcount() affects the refcount cache, it does not write to disk.
Therefore bdrv_flush(bs->file) does nothing. We need to flush the
refcount cache in order to write out the refcount updates!
While we're here also add error returns when qcow2_cache_flush() fails.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
qcow2 images now accept a boolean lazy_refcounts options. Use it like
this:
-drive file=test.qcow2,lazy_refcounts=on
If the option is specified on the command line, it overrides the default
specified by the qcow2 header flags that were set when creating the
image.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
It doesn't do anything yet except storing the options QDict in the
BlockDriverState.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
this patch adds iscsi_truncate which effectively allows for
online resizing of iscsi volumes. for this to work you have
to resize the volume on your storage and then call
block_resize command in qemu which will issue a
readcapacity16 to update the capacity.
v4:
- factor out complete readcapacity logic into a separate function
- handle capacity change check condition in readcapacity function
(this happens if the block_resize cmd is the first iscsi task
executed after a resize on the storage)
v3:
- remove switch statement in iscsi_open
- create separate patch for brdv_drain_all() in bdrv_truncate()
v2:
- add a general bdrv_drain_all() before bdrv_truncate() to avoid
in-flight AIOs while the device is truncated
- since no AIOs are in flight we can use a sync libiscsi call
to re-read the capacity
- factor out the readcapacity16 logic as it is redundant
to iscsi_open() and iscsi_truncate().
Signed-off-by: Peter Lieven <pl@kamp.de>
[allow any type of unit attention check condition in iscsi_readcapacity_sync(),
as in Message-ID: <51263A2A.6070304@dlhnet.de> - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
the storage might return a check condition status for various reasons.
(e.g. bus reset, capacity change, thin-provisioning info etc.)
currently all these informative status responses lead to an I/O error
which is populated to the guest. this patch introduces a retry mechanism
to avoid this.
Signed-off-by: Peter Lieven <pl@kamp.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch adds support for a unix domain socket for a connection
between qemu and local sheepdog server. You can use the unix domain
socket with the following syntax:
$ qemu sheepdog+unix:///<vdiname>?socket=<socket path>[#snapid]
Signed-off-by: MORITA Kazutaka <morita.kazutaka@lab.ntt.co.jp>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This uses the form "<host>:<port>" for the representation of the
sheepdog server to use inet_connect.
Signed-off-by: MORITA Kazutaka <morita.kazutaka@lab.ntt.co.jp>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The URI syntax is consistent with the NBD and Gluster syntax. The
syntax is
sheepdog[+tcp]://[host:port]/vdiname[#snapid|#tag]
Signed-off-by: MORITA Kazutaka <morita.kazutaka@lab.ntt.co.jp>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The qemu-img check command can display fragmentation statistics:
* Total number of clusters in virtual disk
* Number of allocated clusters
* Number of fragmented clusters
This patch adds fragmentation statistics support to qcow2.
Compressed and normal clusters count as allocated. Zero clusters are
not counted as allocated unless their L2 entry has a non-zero offset
(e.g. preallocation).
Only the current L1 table counts towards the statistics - snapshots are
ignored.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The check_refcounts_l1/l2() functions have a check_copied argument to
check that the QCOW_O_COPIED flag is consistent with refcount == 1.
This should be a bool, not an int.
However, the next patch introduces qcow2 fragmentation statistics and
also needs to pass an option to check_refcounts_l1/l2(). This is a good
opportunity to use an int flags field.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This patch adds the support for reporting the image end offset (in
bytes). This is particularly useful after a conversion (or a rebase)
where the destination is a block device in order to find the first
unused byte at the end of the image.
Signed-off-by: Federico Simoncelli <fsimonce@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The curl_easy_setopt(state->curl, CURLOPT_PROTOCOLS, ...) interface was
introduced in libcurl 7.19.4. Therefore we cannot protect against
CVE-2013-0249 when linking against an older libcurl.
This fixes the build failure introduced by
fb6d1bbd24.
Reported-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Tested-by: Andreas Färber <andreas.faeber@web.de>
Message-id: 1360743934-8337-1-git-send-email-stefanha@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
