We can't allow the supervisor to control SEIP as this would allow the
supervisor to clear a pending external interrupt which will result in
lost a interrupt in the case a PLIC is attached. The SEIP bit must be
hardware controlled when a PLIC is attached.
This logic was previously hard-coded so SEIP was always masked even
if no PLIC was attached. This patch adds riscv_cpu_claim_interrupts
so that the PLIC can register control of SEIP. In the case of models
without a PLIC (spike), the SEIP bit remains software controlled.
This interface allows for hardware control of supervisor timer and
software interrupts by other interrupt controller models.
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Sagar Karandikar <sagark@eecs.berkeley.edu>
Cc: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Cc: Alistair Francis <Alistair.Francis@wdc.com>
Signed-off-by: Michael Clark <mjc@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The mode variable only uses the lower 4-bits (M,H,S,U) so
replace the GCC specific __builtin_popcount with ctpop8.
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Sagar Karandikar <sagark@eecs.berkeley.edu>
Cc: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Cc: Alistair Francis <Alistair.Francis@wdc.com>
Signed-off-by: Michael Clark <mjc@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The address calculation for the pending bitfield had
a copy paste bug. This bug went unnoticed because the Linux
PLIC driver does not read the pending bitfield, rather it
reads pending interrupt numbers from the claim register
and writes acknowledgements back to the claim register.
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Sagar Karandikar <sagark@eecs.berkeley.edu>
Cc: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Cc: Alistair Francis <Alistair.Francis@wdc.com>
Reported-by: Vincent Siles <vincent.siles@ens-lyon.org>
Signed-off-by: Michael Clark <mjc@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Change the API of riscv_set_local_interrupt to take a
write mask and value to allow setting and clearing of
multiple local interrupts atomically in a single call.
Rename the new function to riscv_cpu_update_mip.
Signed-off-by: Michael Clark <mjc@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The PLIC previously used a mutex to protect against concurrent
access to the claimed and pending bitfields. Instead of using
a mutex, we update the bitfields using atomic_cmpxchg.
Rename sifive_plic_num_irqs_pending to sifive_plic_irqs_pending
and add an early out if any interrupts are pending as the
count of pending interrupts is not used.
Cc: Sagar Karandikar <sagark@eecs.berkeley.edu>
Cc: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Alistair Francis <Alistair.Francis@wdc.com>
Signed-off-by: Michael Clark <mjc@sifive.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Instead of creating the interrupt in lines with qemu_allocate_irq() use
qdev_init_gpio_in() as this gives us the ability to use the qdev*gpio*()
helpers later on.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Suggested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Michael Clark <mjc@sifive.com>
The PLIC (Platform Level Interrupt Controller) device provides a
parameterizable interrupt controller based on SiFive's PLIC specification.
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Stefan O'Rear <sorear2@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Michael Clark <mjc@sifive.com>
