Most targets were using offsetof(CPUFooState, breakpoints) to determine
how much of CPUFooState to clear on reset. Use the next field after
CPU_COMMON instead, if any, or sizeof(CPUFooState) otherwise.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Note that while such functions may exist both for *-user and softmmu,
only *-user uses the CPUState hook, while softmmu reuses the prototype
for calling it directly.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Default to false.
Tidy variable naming and inline cast uses while at it.
Tested-by: Jia Liu <proljc@gmail.com> (or32)
Signed-off-by: Andreas Färber <afaerber@suse.de>
Add support for AArch32 CRC32 and CRC32C instructions added in ARMv8
and add a CPU feature flag to enable these instructions.
The CRC32-C implementation used is the built-in qemu implementation
and The CRC-32 implementation is from zlib. This requires adding zlib
to LIBS to ensure it is linked for the linux-user binary.
Signed-off-by: Will Newton <will.newton@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1393411566-24104-3-git-send-email-will.newton@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
To avoid complication in code that otherwise would not need to
care about whether EL1 is AArch32 or AArch64, we should store
the interrupt mask bits (CPSR.AIF in AArch32 and PSTATE.DAIF
in AArch64) in one place consistently regardless of EL1's mode.
Since AArch64 has an extra enable bit (D for debug exceptions)
which isn't visible in AArch32, this means we need to keep
the enables in env->pstate. (This is also consistent with the
general approach we're taking that we handle 32 bit CPUs as
being like AArch64/ARMv8 CPUs but which only run in 32 bit mode.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Implement all the AArch64 cache invalidate and clean ops
(which are all NOPs since QEMU doesn't emulate the cache).
The only remaining unimplemented cache op is DC ZVA.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Make the cache ID system registers (CLIDR, CSSELR, CCSIDR, CTR)
visible to AArch64. These are mostly simple 64-bit extensions of the
existing 32 bit system registers and so can share reginfo definitions.
CTR needs to have a split definition, but we can clean up the
temporary user-mode implementation in favour of using the CPU-specified
reset value, and implement the system-mode-required semantics of
restricting its EL0 accessibility if SCTLR.UCT is not set.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
The raw read and write functions were using the ARM_CP_64BIT flag in
ri->type to determine whether to treat the register's state field as
uint32_t or uint64_t; however AArch64 register info structs don't use
that flag. Abstract out the "how big is the field?" test into a
function and fix it to work for AArch64 registers. For this to work
we must ensure that the reginfo structs put into the hashtable have
the correct state field for their use, not the placeholder STATE_BOTH.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
All cpreg read and write functions now return 0, so we can clean up
their prototypes:
* write functions return void
* read functions return the value rather than taking a pointer
to write the value to
This is a fairly mechanical change which makes only the bare
minimum set of changes to the callers of read and write functions.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
The SCTLR is full of bits for enabling or disabling various things, and so
there are many places in the code which check if certain bits are set.
Define some named constants for the SCTLR bits so these checks are easier
to read.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Convert the MIDR register to a property. This allows boards to later set
a custom MIDR value. This has been done in such a way to maintain
compatibility with all existing CPUs and boards
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 878613f2f12d4162f12629522fd99de8df904856.1390176489.git.alistair.francis@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Switch the ARMCPUInfo arrays in cpu.c and cpu64.c to use a terminator
entry rather than looping based on ARRAY_SIZE. The latter causes
compile warnings on some versions of gcc if the configure options
happen to result in an empty array.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Replace assert_no_error() usages with the error_abort system.
&error_abort is passed into API calls to signal to the Error sub-system
that any errors are fatal. Removes need for caller assertions.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
The env->pstate field is a little odd since it doesn't strictly
speaking represent an architectural register. However it's convenient
for QEMU to use it to hold the various PSTATE architectural bits
in the same format the architecture specifies for SPSR registers
(since this is the same format the kernel uses for signal handlers
and the KVM register). Add some structure to how we deal with it:
* document what env->pstate is
* add some #defines for various bits in it
* add helpers for reading/writing it taking account of caching
of NZCV, and use them where appropriate
* reset it on startup
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1385645602-18662-3-git-send-email-peter.maydell@linaro.org
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
If hivecs are being used on reset, the CPU should come out of reset at
the hivecs reset vector (0xFFFF0000)
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 3afc69c4f58f60aa2bbee7b91574a4eb414b1c23.1387160489.git.peter.crosthwaite@xilinx.com
[ PC Changes:
* Fixed Grammar error in commit message
* Elaborated commit message.
]
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add an ARM CPU property for the reset value of hivecs as it is a
board/SoC configurable setting.
The existence of the property is conditional on the ARM CPU not being M
class.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: b04216c6bda4bd163f44a55bba552d0e8267481f.1387160489.git.peter.crosthwaite@xilinx.com
[ PC Changes:
* Elaborated commit message
* refactored to use qdev_property_add_static
]
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The reset value of the CP15 CBAR is a vendor (machine) configurable
property. If ARM_FEATURE_CBAR is set, add it as a property at
post_init time.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 2f1eec3f912135deea6252360e03645003d12e0a.1387160489.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some processors (notably A9 within Highbank) define and use the
CP15 configuration base address (CBAR). This is vendor specific
so its best implemented as a CPU property (otherwise we would need
vendor specific child classes for every ARM implementation).
This patch prepares support for converting CBAR reset value to
a CPU property by moving the CP registration out of the CPU
init fn, as registration will need to happen at realize time
to pick up any property updates. The easiest way to do this
is via definition of a new ARM_FEATURE to flag the existence
of the register.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 9f697ef1e2ee60a3b9ef971a7f3bc3fa6752a9b7.1387160489.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This adds support for the AESE/AESD/AESMC/AESIMC instructions that
are available on some v8 implementations of Aarch32.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Message-id: 1386266078-6976-1-git-send-email-ard.biesheuvel@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Instead of assuming that a KVM target CPU must always be a
Cortex-A15 and hardcoding this in kvm_arch_init_vcpu(),
store the KVM_ARM_TARGET_* value in the ARMCPU class,
and use that.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Message-id: 1385140638-10444-10-git-send-email-peter.maydell@linaro.org
New ARM boards are generally expected to boot their secondary CPUs
via the PSCI interface, rather than ad-hoc "loop around in holding
pen code" as hw/arm/boot.c implements. In particular this is
necessary for mach-virt kernels. For KVM we achieve this by creating
the VCPUs with a feature flag marking them as starting in PSCI
powered-down state; the guest kernel will then make a PSCI call
(implemented in the host kernel) to start the secondaries at
an address of its choosing once it has got the primary CPU up.
Implement this setting of the feature flag, controlled by a
qdev property for ARMCPU, which board code can set if it is a
PSCI system.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Message-id: 1385140638-10444-7-git-send-email-peter.maydell@linaro.org
Linux requires device tree CPU nodes to include a 'compatible'
string describing the CPU. Add a field in the ARMCPU struct for
this so that boards which construct a device tree can insert
the correct CPU nodes.
Note that there is currently no officially specified 'compatible'
string for the TI925T, Cortex-M3 or SA1110 CPUs.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Message-id: 1385140638-10444-6-git-send-email-peter.maydell@linaro.org
This patch adds all the prerequisites for AArch64 support that didn't
fit into split up patches. It extends important bits in the core cpu
headers to also take AArch64 mode into account.
Add new ARM_TBFLAG_AARCH64_STATE translation buffer flag
indicate an ARMv8 cpu running in aarch64 mode vs aarch32 mode.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: John Rigby <john.rigby@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1378235544-22290-10-git-send-email-peter.maydell@linaro.org
Message-id: 1368505980-17151-4-git-send-email-john.rigby@linaro.org
[PMM:
* rearranged tbflags so AArch64? is bit 31 and if it is set then
30..0 are freely available for whatever makes most sense for that mode
* added version bump since we change VFP migration state
* added a comment about how VFP/Neon register state works
* physical address space is 48 bits, not 64
* added ARM_FEATURE_AARCH64 flag to identify 64-bit capable CPUs
]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If we're building aarch64-linux-user then the 32 bit CPUs are
all unwanted, because they can't possibly execute the 64 bit
binaries we will be running; disable them.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1378235544-22290-9-git-send-email-peter.maydell@linaro.org
When the initial SP is loaded from the vector table on ARMv7M systems the two
least significant bits are ignored as the stack is always aligned at a four byte
boundary (see ARM DDI 0403C, B1.4.1 and B1.5.5). So far QEMU did not ignore
these bits leading to a stack alignment inconsitent with real hardware for
binaries that rely on this behaviour. This patch fixes this issue by masking the
two least significant bits when loading the SP.
Signed-off-by: Sebastian Ottlik <ottlik@fzi.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1378286595-27072-1-git-send-email-ottlik@fzi.de
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Make the 'any' CPU for target-arm available only in linux-user mode.
The ARM target provides a CPU named "any", which turns on support for
all user-level instruction set extensions we know about. This is
intended for linux-user emulation mode, where it is the default CPU type.
It makes no sense to try to use this for system emulation, since we don't
initialize it with any system-level information like feature register
values or implementation specific cp15 registers. (Unsurprisingly, some
boards won't boot at all, though you might get lucky in some cases where
the guest doesn't happen to prod things that aren't there.)
Prevent users from making this command line error by removing the
CPU definition from the softmmu build.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Message-id: 1378213995-12945-1-git-send-email-peter.maydell@linaro.org
This is an autogenerated patch using scripts/switch-timer-api.
Switch the entire code base to using the new timer API.
Note this patch may introduce some line length issues.
Signed-off-by: Alex Bligh <alex@alex.org.uk>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The ARMv7 architecture specifies a 'generic timer' which is implemented
via cp15 registers. Newer kernels will prefer to use this rather than
a devboard-level timer. Implement the generic timer for TCG; for KVM
we will already use the hardware's virtualized timer for this.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Laurent Desnogues <laurent.desnogues@gmail.com>
Message-id: 1376065080-26661-4-git-send-email-peter.maydell@linaro.org
Now that ARMCPU is a subclass of DeviceState, we can make the
CPU's inbound IRQ and FIQ lines be simply gpio lines, which
means we can remove the odd arm_pic shim.
We retain the arm_pic_init_cpu() function as a backwards
compatibility shim layer so we can convert the board models
to get the IRQ and FIQ lines directly from the ARMCPU
object one at a time.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1375977856-25046-2-git-send-email-peter.maydell@linaro.org
Commit c643bed99 moved qemu_init_vcpu() calls to common CPUState code.
This causes x86 cpu-add to fail with "KVM: setting VAPIC address failed".
The reason for the failure is that CPUClass::kvm_fd is not yet
initialized in the following call graph:
->x86_cpu_realizefn
->x86_cpu_apic_realize
->qdev_init
->device_set_realized
->device_reset (hotplugged == 1)
->apic_reset_common
->vapic_base_update
->kvm_apic_vapic_base_update
This causes attempted KVM vCPU ioctls to fail.
By contrast, in the non-hotplug case the APIC is reset much later, when
the vCPU is already initialized.
As a quick and safe solution, move the qemu_init_vcpu() call back into
the targets' realize functions.
Reported-by: Chen Fan <chen.fan.fnst@cn.fujitsu.com>
Acked-by: Igor Mammedov <imammedo@redhat.com> (for i386)
Tested-by: Jia Liu <proljc@gmail.com> (for openrisc)
Signed-off-by: Andreas Färber <afaerber@suse.de>
Replace the GDB_CORE_XML define in gdbstub.c with a CPUClass field.
Use first_cpu for qSupported and qXfer:features:read: for now.
Add a stub for xml_builtin.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Completes migration of target-specific code to new target-*/gdbstub.c.
Acked-by: Michael Walle <michael@walle.cc> (for lm32)
Acked-by: Max Filippov <jcmvbkbc@gmail.com> (for xtensa)
Signed-off-by: Andreas Färber <afaerber@suse.de>
CPUState::gdb_num_regs replaces num_g_regs.
CPUClass::gdb_num_core_regs replaces NUM_CORE_REGS.
Allows building gdb_register_coprocessor() for xtensa, too.
As a side effect this should fix coprocessor register numbering for SMP.
Acked-by: Michael Walle <michael@walle.cc> (for lm32)
Acked-by: Max Filippov <jcmvbkbc@gmail.com> (for xtensa)
Signed-off-by: Andreas Färber <afaerber@suse.de>
Change breakpoint_invalidate() argument to CPUState alongside.
Since all targets now assign a softmmu-only field, we can drop helpers
cpu_class_set_{do_unassigned_access,vmsd}() and device_class_set_vmsd().
Prepares for changing cpu_memory_rw_debug() argument to CPUState.
Acked-by: Max Filippov <jcmvbkbc@gmail.com> (for xtensa)
Signed-off-by: Andreas Färber <afaerber@suse.de>
This moves setting the Program Counter from gdbstub into target code.
Use vaddr type as upper-bound replacement for target_ulong.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
x86 was using additional CPU_DUMP_* flags, so make that configurable in
CPUClass::reset_dump_flags.
This adds reset logging for alpha, unicore32 and xtensa.
Acked-by: Michael Walle <michael@walle.cc> (for lm32)
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Since commit 878096eeb2 (cpu: Turn
cpu_dump_{state,statistics}() into CPUState hooks) CPUArchState is no
longer needed.
Add documentation and make the functions available through qemu/log.h
outside NEED_CPU_H to allow use in qom/cpu.c. Moving them to qom/cpu.h
was not yet possible due to convoluted include paths, so that some
devices grow an implicit and unneeded dependency on qom/cpu.h for now.
Acked-by: Michael Walle <michael@walle.cc> (for lm32)
Reviewed-by: Richard Henderson <rth@twiddle.net>
[AF: Simplified mb_cpu_do_interrupt() and do_interrupt_all() changes]
Signed-off-by: Andreas Färber <afaerber@suse.de>
This allows to move the call into CPUState's realizefn.
Therefore move the stub into libqemustub.a.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Make cpustats monitor command available unconditionally.
Prepares for changing kvm_handle_internal_error() and kvm_cpu_exec()
arguments to CPUState.
Signed-off-by: Andreas Färber <afaerber@suse.de>
The v7 ARM ARM specifies that the Large Physical Address
Extension requires implementation of the Multiprocessing
Extensions, so make our LPAE feature imply V7MP rather
than specifying both in the A15 CPU initfn.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Message-id: 1371127899-10364-1-git-send-email-peter.maydell@linaro.org
Convert the TCG ARM target to using an (index,value) list for migrating
coprocessors. The primary benefit of the (index,value) list is for
passing state between KVM and QEMU, but it works for TCG-to-TCG
migration as well and is a useful self-contained first step.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Port the ARM CPU save/load code to use VMState. Some state is
saved in a slightly different order to simplify things -- for
example arrays are saved one after the other rather than 'striped',
and we always save all 32 VFP registers even if the CPU happens
to only have 16.
Use one subsection for each feature. This means that we don't need to
bump the version field each time that a new feature gets introduced.
Signed-off-by: Juan Quintela <quintela@redhat.com>
[PMM: fixed conflicts, updated to use cpu_class_set_vmsd(), updated
with new/removed fields since original patch, changed to use custom
VMStateInfo for cpsr rather than presave/postload hooks, corrected
subsection names so vmload doesn't fail]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Enable ARMCPUInfo to specify a custom class_init functions.
Introduce arm_v7m_class_init() and use it for "cortex-m3" model.
Instead of forwarding from arm_cpu_do_interrupt() to do_interrupt_v7m(),
override CPUClass::do_interrupt with arm_v7m_cpu_do_interrupt()
in arm_v7m_class_init().
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
This removes a global per-target function and thus takes us one step
closer to compiling multiple targets into one executable.
It will also allow to override the interrupt handling for certain CPU
families.
Signed-off-by: Andreas Färber <afaerber@suse.de>
The target-specific ENV_GET_CPU() macros have allowed us to navigate
from CPUArchState to CPUState. The reverse direction was not supported.
Avoid introducing CPU_GET_ENV() macros by initializing an untyped
pointer that is initialized in derived instance_init functions.
The field may not be called "env" due to it being poisoned.
Acked-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Turn arm_cpu_realize() into a QOM realize function, no longer called
via cpu.h prototype. To maintain the semantics of cpu_init(), set
realized = true explicitly in cpu_arm_init().
Move GDB coprocessor registration, CPU reset and vCPU initialization
into the realizefn.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Andreas Färber
Will Newton
Peter Maydell
Alistair Francis
Edgar E. Iglesias
Peter Crosthwaite
Antony Pavlov
Ard Biesheuvel
Alexander Graf
Sebastian Ottlik
Alex Bligh
Mans Rullgard
Juan Quintela