pcie_sriov_pf_disable_vfs() is called when resetting the PF, but it only
disables VFs and does not reset SR-IOV extended capability, leaking the
state and making the VF Enable register inconsistent with the actual
state.
Replace pcie_sriov_pf_disable_vfs() with pcie_sriov_pf_reset(), which
does not only disable VFs but also resets the capability.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Message-Id: <20240228-reuse-v8-3-282660281e60@daynix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@ericsson.com>
The guest may write NumVFs greater than TotalVFs and that can lead
to buffer overflow in VF implementations.
Cc: qemu-stable@nongnu.org
Fixes: CVE-2024-26327
Fixes: 7c0fa8dff8 ("pcie: Add support for Single Root I/O Virtualization (SR/IOV)")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Message-Id: <20240228-reuse-v8-2-282660281e60@daynix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@ericsson.com>
nvme_sriov_pre_write_ctrl() used to directly inspect SR-IOV
configurations to know the number of VFs being disabled due to SR-IOV
configuration writes, but the logic was flawed and resulted in
out-of-bound memory access.
It assumed PCI_SRIOV_NUM_VF always has the number of currently enabled
VFs, but it actually doesn't in the following cases:
- PCI_SRIOV_NUM_VF has been set but PCI_SRIOV_CTRL_VFE has never been.
- PCI_SRIOV_NUM_VF was written after PCI_SRIOV_CTRL_VFE was set.
- VFs were only partially enabled because of realization failure.
It is a responsibility of pcie_sriov to interpret SR-IOV configurations
and pcie_sriov does it correctly, so use pcie_sriov_num_vfs(), which it
provides, to get the number of enabled VFs before and after SR-IOV
configuration writes.
Cc: qemu-stable@nongnu.org
Fixes: CVE-2024-26328
Fixes: 11871f53ef ("hw/nvme: Add support for the Virtualization Management command")
Suggested-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Message-Id: <20240228-reuse-v8-1-282660281e60@daynix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Felix Wu <flwu@google.com>
Signed-off-by: Nabih Estefan <nabihestefan@google.com>
Message-Id: <20240221170027.1027325-3-nabihestefan@google.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Version 2.1+.
Signed-off-by: Felix Wu <flwu@google.com>
Signed-off-by: Nabih Estefan <nabihestefan@google.com>
Message-Id: <20240221170027.1027325-2-nabihestefan@google.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
IOAPICCommonClass implements its own private realize(), and this private
realize() allows error.
Since IOAPICCommonClass.realize() returns void, to check the error,
dereference @errp with ERRP_GUARD().
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Message-Id: <20240223085653.1255438-8-zhao1.liu@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
As the comment in qapi/error, dereferencing @errp requires
ERRP_GUARD():
* = Why, when and how to use ERRP_GUARD() =
*
* Without ERRP_GUARD(), use of the @errp parameter is restricted:
* - It must not be dereferenced, because it may be null.
...
* ERRP_GUARD() lifts these restrictions.
*
* To use ERRP_GUARD(), add it right at the beginning of the function.
* @errp can then be used without worrying about the argument being
* NULL or &error_fatal.
*
* Using it when it's not needed is safe, but please avoid cluttering
* the source with useless code.
But in iommufd_cdev_getfd(), @errp is dereferenced without ERRP_GUARD():
if (*errp) {
error_prepend(errp, VFIO_MSG_PREFIX, path);
}
Currently, since vfio_attach_device() - the caller of
iommufd_cdev_getfd() - is always called in DeviceClass.realize() context
and doesn't get the NULL @errp parameter, iommufd_cdev_getfd()
hasn't triggered the bug that dereferencing the NULL @errp.
To follow the requirement of @errp, add missing ERRP_GUARD() in
iommufd_cdev_getfd().
Suggested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20240223085653.1255438-7-zhao1.liu@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
As the comment in qapi/error, dereferencing @errp requires
ERRP_GUARD():
* = Why, when and how to use ERRP_GUARD() =
*
* Without ERRP_GUARD(), use of the @errp parameter is restricted:
* - It must not be dereferenced, because it may be null.
...
* ERRP_GUARD() lifts these restrictions.
*
* To use ERRP_GUARD(), add it right at the beginning of the function.
* @errp can then be used without worrying about the argument being
* NULL or &error_fatal.
*
* Using it when it's not needed is safe, but please avoid cluttering
* the source with useless code.
But in cxl_usp_realize(), @errp is dereferenced without ERRP_GUARD():
cxl_doe_cdat_init(cxl_cstate, errp);
if (*errp) {
goto err_cap;
}
Here we check *errp, because cxl_doe_cdat_init() returns void. And since
cxl_usp_realize() - as a PCIDeviceClass.realize() method - doesn't get
the NULL @errp parameter, it hasn't triggered the bug that dereferencing
the NULL @errp.
To follow the requirement of @errp, add missing ERRP_GUARD() in
cxl_usp_realize().
Suggested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20240223085653.1255438-6-zhao1.liu@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
As the comment in qapi/error, dereferencing @errp requires
ERRP_GUARD():
* = Why, when and how to use ERRP_GUARD() =
*
* Without ERRP_GUARD(), use of the @errp parameter is restricted:
* - It must not be dereferenced, because it may be null.
...
* ERRP_GUARD() lifts these restrictions.
*
* To use ERRP_GUARD(), add it right at the beginning of the function.
* @errp can then be used without worrying about the argument being
* NULL or &error_fatal.
*
* Using it when it's not needed is safe, but please avoid cluttering
* the source with useless code.
But in trng_prop_fault_event_set, @errp is dereferenced without
ERRP_GUARD():
visit_type_uint32(v, name, events, errp);
if (*errp) {
return;
}
Currently, since trng_prop_fault_event_set() doesn't get the NULL @errp
parameter as a "set" method of object property, it hasn't triggered the
bug that dereferencing the NULL @errp.
And since visit_type_uint32() returns bool, check the returned bool
directly instead of dereferencing @errp, then we needn't the add missing
ERRP_GUARD().
Suggested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Message-Id: <20240223085653.1255438-5-zhao1.liu@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
As the comment in qapi/error, dereferencing @errp requires
ERRP_GUARD():
* = Why, when and how to use ERRP_GUARD() =
*
* Without ERRP_GUARD(), use of the @errp parameter is restricted:
* - It must not be dereferenced, because it may be null.
...
* ERRP_GUARD() lifts these restrictions.
*
* To use ERRP_GUARD(), add it right at the beginning of the function.
* @errp can then be used without worrying about the argument being
* NULL or &error_fatal.
*
* Using it when it's not needed is safe, but please avoid cluttering
* the source with useless code.
But in ct3_realize(), @errp is dereferenced without ERRP_GUARD():
cxl_doe_cdat_init(cxl_cstate, errp);
if (*errp) {
goto err_free_special_ops;
}
Here we check *errp, because cxl_doe_cdat_init() returns void. And
ct3_realize() - as a PCIDeviceClass.realize() method - doesn't get the
NULL @errp parameter, it hasn't triggered the bug that dereferencing
the NULL @errp.
To follow the requirement of @errp, add missing ERRP_GUARD() in
ct3_realize().
Suggested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20240223085653.1255438-4-zhao1.liu@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
As the comment in qapi/error, dereferencing @errp requires
ERRP_GUARD():
* = Why, when and how to use ERRP_GUARD() =
*
* Without ERRP_GUARD(), use of the @errp parameter is restricted:
* - It must not be dereferenced, because it may be null.
...
* ERRP_GUARD() lifts these restrictions.
*
* To use ERRP_GUARD(), add it right at the beginning of the function.
* @errp can then be used without worrying about the argument being
* NULL or &error_fatal.
*
* Using it when it's not needed is safe, but please avoid cluttering
* the source with useless code.
But in macfb_nubus_realize(), @errp is dereferenced without
ERRP_GUARD():
ndc->parent_realize(dev, errp);
if (*errp) {
return;
}
Here we check *errp, because the ndc->parent_realize(), as a
DeviceClass.realize() callback, returns void. And since
macfb_nubus_realize(), also as a DeviceClass.realize(), doesn't get the
NULL @errp parameter, it hasn't triggered the bug that dereferencing the
NULL @errp.
To follow the requirement of @errp, add missing ERRP_GUARD() in
macfb_nubus_realize().
Suggested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20240223085653.1255438-3-zhao1.liu@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
As the comment in qapi/error, dereferencing @errp requires
ERRP_GUARD():
* = Why, when and how to use ERRP_GUARD() =
*
* Without ERRP_GUARD(), use of the @errp parameter is restricted:
* - It must not be dereferenced, because it may be null.
...
* ERRP_GUARD() lifts these restrictions.
*
* To use ERRP_GUARD(), add it right at the beginning of the function.
* @errp can then be used without worrying about the argument being
* NULL or &error_fatal.
*
* Using it when it's not needed is safe, but please avoid cluttering
* the source with useless code.
But in cxl_fixed_memory_window_config(), @errp is dereferenced in 2
places without ERRP_GUARD():
fw->enc_int_ways = cxl_interleave_ways_enc(fw->num_targets, errp);
if (*errp) {
return;
}
and
fw->enc_int_gran =
cxl_interleave_granularity_enc(object->interleave_granularity,
errp);
if (*errp) {
return;
}
For the above 2 places, we check "*errp", because neither function
returns a suitable error code. And since machine_set_cfmw() - the caller
of cxl_fixed_memory_window_config() - doesn't get the NULL @errp
parameter as the "set" method of object property,
cxl_fixed_memory_window_config() hasn't triggered the bug that
dereferencing the NULL @errp.
To follow the requirement of @errp, add missing ERRP_GUARD() in
cxl_fixed_memory_window_config().
Suggested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20240223085653.1255438-2-zhao1.liu@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch adds support for VDPA network simulation devices.
The device is developed based on virtio-net and tap backend,
and supports hardware live migration function.
For more details, please refer to "docs/system/devices/vdpa-net.rst"
Signed-off-by: Hao Chen <chenh@yusur.tech>
Message-Id: <20240221073802.2888022-1-chenh@yusur.tech>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Shared objects lack spoofing protection.
For VHOST_USER_BACKEND_SHARED_OBJECT_REMOVE messages
received by the vhost-user interface, any backend was
allowed to remove entries from the shared table just
by knowing the UUID. Only the owner of the entry
shall be allowed to removed their resources
from the table.
To fix that, add a check for all
*SHARED_OBJECT_REMOVE messages received.
A vhost device can only remove TYPE_VHOST_DEV
entries that are owned by them, otherwise skip
the removal, and inform the device that the entry
has not been removed in the answer.
Signed-off-by: Albert Esteve <aesteve@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20240219143423.272012-2-aesteve@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The payload size returned by command VIRTIO_SND_R_PCM_INFO is
wrong. The code in process_cmd() assumes that all commands
return only a virtio_snd_hdr payload, but some commands like
VIRTIO_SND_R_PCM_INFO may return an additional payload.
Add a zero initialized payload_size variable to struct
virtio_snd_ctrl_command to allow for additional payloads.
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Volker Rümelin <vr_qemu@t-online.de>
Message-Id: <20240218083351.8524-1-vr_qemu@t-online.de>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This CXL component isn't allowed to have a RAS capability.
Whilst this should be harmless as software is not expected to look
here, good to clean it up.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240215155206.2736-1-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Sometimes, certain parts are not being skipped in
vhost_vdpa_listener_region_del, but they are skipped in
vhost_vdpa_listener_region_add, or vice versa. The vhost-vdpa code
expects all parts to maintain their properties, so we're adding a trace
to help with debugging when any part is skipped.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <20240215103616.330518-3-eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Next changes uses this variables, so avoid call repeatedly to memory
region functions. No functional change intended.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <20240215103616.330518-2-eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch extends the PCIe link speed option so that slots can be
configured as supporting 32GT/s (Gen5) or 64GT/s (Gen5) speeds.
This is as simple as setting the appropriate bit in LnkCap2 and
the appropriate value in LnkCap and LnkCtl2.
Signed-off-by: Lukas Stockner <lstockner@genesiscloud.com>
Message-Id: <20240215012326.3272366-1-lstockner@genesiscloud.com>
Reviewed-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We already use MADV_NORESERVE to deal with sparse memory regions. Let's
also set madvise(MADV_DONTDUMP), otherwise a crash of the process can
result in us allocating all memory in the mmap'ed region for dumping
purposes.
This change implies that the mmap'ed rings won't be included in a
coredump. If ever required for debugging purposes, we could mark only
the mapped rings MADV_DODUMP.
Ignore errors during madvise() for now.
Reviewed-by: Raphael Norwitz <raphael@enfabrica.net>
Acked-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20240214151701.29906-15-david@redhat.com>
Tested-by: Mario Casquero <mcasquer@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Currently, we try to remap all rings whenever we add a single new memory
region. That doesn't quite make sense, because we already map rings when
setting the ring address, and panic if that goes wrong. Likely, that
handling was simply copied from set_mem_table code, where we actually
have to remap all rings.
Remapping all rings might require us to walk quite a lot of memory
regions to perform the address translations. Ideally, we'd simply remove
that remapping.
However, let's be a bit careful. There might be some weird corner cases
where we might temporarily remove a single memory region (e.g., resize
it), that would have worked for now. Further, a ring might be located on
hotplugged memory, and as the VM reboots, we might unplug that memory, to
hotplug memory before resetting the ring addresses.
So let's unmap affected rings as we remove a memory region, and try
dynamically mapping the ring again when required.
Acked-by: Raphael Norwitz <raphael@enfabrica.net>
Acked-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20240214151701.29906-14-david@redhat.com>
Tested-by: Mario Casquero <mcasquer@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Let's factor it out to prepare for further changes.
Reviewed-by: Raphael Norwitz <raphael@enfabrica.net>
Acked-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20240214151701.29906-13-david@redhat.com>
Tested-by: Mario Casquero <mcasquer@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In the past, QEMU would create memory regions that could partially cover
hugetlb pages, making mmap() fail if we would use the mmap_offset as an
fd_offset. For that reason, we never used the mmap_offset as an offset into
the fd and instead always mapped the fd from the very start.
However, that can easily result in us mmap'ing a lot of unnecessary
parts of an fd, possibly repeatedly.
QEMU nowadays does not create memory regions that partially cover huge
pages -- it never really worked with postcopy. QEMU handles merging of
regions that partially cover huge pages (due to holes in boot memory) since
2018 in c1ece84e7c ("vhost: Huge page align and merge").
Let's be a bit careful and not unconditionally convert the
mmap_offset into an fd_offset. Instead, let's simply detect the hugetlb
size and pass as much as we can as fd_offset, making sure that we call
mmap() with a properly aligned offset.
With QEMU and a virtio-mem device that is fully plugged (50GiB using 50
memslots) the qemu-storage daemon process consumes in the VA space
1281GiB before this change and 58GiB after this change.
================ Vhost user message ================
Request: VHOST_USER_ADD_MEM_REG (37)
Flags: 0x9
Size: 40
Fds: 59
Adding region 4
guest_phys_addr: 0x0000000200000000
memory_size: 0x0000000040000000
userspace_addr: 0x00007fb73bffe000
old mmap_offset: 0x0000000080000000
fd_offset: 0x0000000080000000
new mmap_offset: 0x0000000000000000
mmap_addr: 0x00007f02f1bdc000
Successfully added new region
================ Vhost user message ================
Request: VHOST_USER_ADD_MEM_REG (37)
Flags: 0x9
Size: 40
Fds: 59
Adding region 5
guest_phys_addr: 0x0000000240000000
memory_size: 0x0000000040000000
userspace_addr: 0x00007fb77bffe000
old mmap_offset: 0x00000000c0000000
fd_offset: 0x00000000c0000000
new mmap_offset: 0x0000000000000000
mmap_addr: 0x00007f0284000000
Successfully added new region
Reviewed-by: Raphael Norwitz <raphael@enfabrica.net>
Acked-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20240214151701.29906-12-david@redhat.com>
Tested-by: Mario Casquero <mcasquer@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Let's speed up GPA to memory region / virtual address lookup. Store the
memory regions ordered by guest physical addresses, and use binary
search for address translation, as well as when adding/removing memory
regions.
Most importantly, this will speed up GPA->VA address translation when we
have many memslots.
Reviewed-by: Raphael Norwitz <raphael@enfabrica.net>
Acked-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20240214151701.29906-11-david@redhat.com>
Tested-by: Mario Casquero <mcasquer@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Memory regions cannot overlap, and if we ever hit that case something
would be really flawed.
For example, when vhost code in QEMU decides to increase the size of memory
regions to cover full huge pages, it makes sure to never create overlaps,
and if there would be overlaps, it would bail out.
QEMU commits 48d7c97577 ("vhost: Merge sections added to temporary
list"), c1ece84e7c ("vhost: Huge page align and merge") and
e7b94a84b6 ("vhost: Allow adjoining regions") added and clarified that
handling and how overlaps are impossible.
Consequently, each GPA can belong to at most one memory region, and
everything else doesn't make sense. Let's factor out our search to prepare
for further changes.
Reviewed-by: Raphael Norwitz <raphael@enfabrica.net>
Acked-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20240214151701.29906-10-david@redhat.com>
Tested-by: Mario Casquero <mcasquer@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We cannot have duplicate memory regions, something would be deeply
flawed elsewhere. Let's just stop the search once we found an entry.
We'll add more sanity checks when adding memory regions later.
Reviewed-by: Raphael Norwitz <raphael@enfabrica.net>
Acked-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20240214151701.29906-9-david@redhat.com>
Tested-by: Mario Casquero <mcasquer@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
dev->nregions always covers only valid entries. Stop zeroing out other
array elements that are unused.
Reviewed-by: Raphael Norwitz <raphael@enfabrica.net>
Acked-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20240214151701.29906-8-david@redhat.com>
Tested-by: Mario Casquero <mcasquer@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We never add a memory region if mmap() failed. Therefore, no need to check
for NULL.
Reviewed-by: Raphael Norwitz <raphael@enfabrica.net>
Acked-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20240214151701.29906-7-david@redhat.com>
Tested-by: Mario Casquero <mcasquer@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Let's factor it out, reducing quite some code duplication and perparing
for further changes.
If we fail to mmap a region and panic, we now simply don't add that
(broken) region.
Note that we now increment dev->nregions as we are successfully
adding memory regions, and don't increment dev->nregions if anything went
wrong.
Reviewed-by: Raphael Norwitz <raphael@enfabrica.net>
Acked-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20240214151701.29906-6-david@redhat.com>
Tested-by: Mario Casquero <mcasquer@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Let's reduce some code duplication and prepare for further changes.
Reviewed-by: Raphael Norwitz <raphael@enfabrica.net>
Acked-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20240214151701.29906-5-david@redhat.com>
Tested-by: Mario Casquero <mcasquer@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Let's factor it out. Note that the check for MAP_FAILED was wrong as
we never set mmap_addr if mmap() failed. We'll remove the NULL check
separately.
Reviewed-by: Raphael Norwitz <raphael@enfabrica.net>
Acked-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20240214151701.29906-4-david@redhat.com>
Tested-by: Mario Casquero <mcasquer@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Let's support up to 509 mem slots, just like vhost in the kernel usually
does and the rust vhost-user implementation recently [1] started doing.
This is required to properly support memory hotplug, either using
multiple DIMMs (ACPI supports up to 256) or using virtio-mem.
The 509 used to be the KVM limit, it supported 512, but 3 were
used for internal purposes. Currently, KVM supports more than 512, but
it usually doesn't make use of more than ~260 (i.e., 256 DIMMs + boot
memory), except when other memory devices like PCI devices with BARs are
used. So, 509 seems to work well for vhost in the kernel.
Details can be found in the QEMU change that made virtio-mem consume
up to 256 mem slots across all virtio-mem devices. [2]
509 mem slots implies 509 VMAs/mappings in the worst case (even though,
in practice with virtio-mem we won't be seeing more than ~260 in most
setups).
With max_map_count under Linux defaulting to 64k, 509 mem slots
still correspond to less than 1% of the maximum number of mappings.
There are plenty left for the application to consume.
[1] https://github.com/rust-vmm/vhost/pull/224
[2] https://lore.kernel.org/all/20230926185738.277351-1-david@redhat.com/
Reviewed-by: Raphael Norwitz <raphael@enfabrica.net>
Acked-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20240214151701.29906-3-david@redhat.com>
Tested-by: Mario Casquero <mcasquer@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Let's prepare for increasing VHOST_USER_MAX_RAM_SLOTS by dynamically
allocating dev->regions. We don't have any ABI guarantees (not
dynamically linked), so we can simply change the layout of VuDev.
Let's zero out the memory, just as we used to do.
Reviewed-by: Raphael Norwitz <raphael@enfabrica.net>
Acked-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20240214151701.29906-2-david@redhat.com>
Tested-by: Mario Casquero <mcasquer@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Fix an issue where cancellation of ongoing migration ends up
with no network connectivity.
When canceling migration, SVQ will be switched back to the
passthrough mode, but the right call fd is not programed to
the device and the svq's own call fd is still used. At the
point of this transitioning period, the shadow_vqs_enabled
hadn't been set back to false yet, causing the installation
of call fd inadvertently bypassed.
Message-Id: <1707910082-10243-13-git-send-email-si-wei.liu@oracle.com>
Fixes: a8ac88585d ("vhost: Add Shadow VirtQueue call forwarding capabilities")
Cc: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Si-Wei Liu <si-wei.liu@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
svq_switching indicates the transitional state whether
or not SVQ mode switching is in progress, and towards
which direction. Add the neccessary state around where
the switching would take place.
Message-Id: <1707910082-10243-12-git-send-email-si-wei.liu@oracle.com>
Signed-off-by: Si-Wei Liu <si-wei.liu@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Will be used in following patches.
DISABLING(-1) means SVQ is being switched off to passthrough
mode.
ENABLING(1) means passthrough VQs are being switched to SVQ.
DONE(0) means SVQ switching is completed.
Message-Id: <1707910082-10243-11-git-send-email-si-wei.liu@oracle.com>
Signed-off-by: Si-Wei Liu <si-wei.liu@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
For better debuggability and observability.
Message-Id: <1707910082-10243-10-git-send-email-si-wei.liu@oracle.com>
Reviewed-by: Eugenio Pérez <eperezma@redhat.com>
Signed-off-by: Si-Wei Liu <si-wei.liu@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
For better debuggability and observability.
Message-Id: <1707910082-10243-9-git-send-email-si-wei.liu@oracle.com>
Reviewed-by: Eugenio Pérez <eperezma@redhat.com>
Signed-off-by: Si-Wei Liu <si-wei.liu@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
For better debuggability and observability.
Message-Id: <1707910082-10243-8-git-send-email-si-wei.liu@oracle.com>
Reviewed-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Si-Wei Liu <si-wei.liu@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
For better debuggability and observability.
Message-Id: <1707910082-10243-7-git-send-email-si-wei.liu@oracle.com>
Reviewed-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Si-Wei Liu <si-wei.liu@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
For better debuggability and observability.
Message-Id: <1707910082-10243-6-git-send-email-si-wei.liu@oracle.com>
Reviewed-by: Eugenio Pérez <eperezma@redhat.com>
Signed-off-by: Si-Wei Liu <si-wei.liu@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Introduce new API. No functional change on existing API.
Message-Id: <1707910082-10243-5-git-send-email-si-wei.liu@oracle.com>
Reviewed-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Si-Wei Liu <si-wei.liu@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Generalize duplicated condition check for the last vq of vdpa
device to a common function.
Message-Id: <1707910082-10243-4-git-send-email-si-wei.liu@oracle.com>
Reviewed-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Si-Wei Liu <si-wei.liu@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Previous commits had it removed. Now adding it back because
this function will be needed by future patches.
Message-Id: <1707910082-10243-2-git-send-email-si-wei.liu@oracle.com>
Reviewed-by: Eugenio Pérez <eperezma@redhat.com>
Signed-off-by: Si-Wei Liu <si-wei.liu@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add reset support for mcf5208.
Signed-off-by: Angelo Dureghello <angelo@kernel-space.org>
Reviewed-by: Thomas Huth <huth@tuxfamily.org>
Message-ID: <20240309093459.984565-1-angelo@kernel-space.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
The support for "parameter=0" SMP configurations is removed, and QEMU
returns error for those cases.
So add the related test cases to ensure parameters can't accept 0.
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-ID: <20240308160148.3130837-14-zhao1.liu@linux.intel.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
The smp_props.has_clusters in MachineClass is not a user configured
field, and it indicates if user specifies "clusters" in -smp.
After -smp parsing, other module could aware if the cluster level
is configured by user. This is used when the machine has only 1 cluster
since there's only 1 cluster by default.
Add the check to cover this field.
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Tested-by: Xiaoling Song <xiaoling.song@intel.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Message-ID: <20240308160148.3130837-13-zhao1.liu@linux.intel.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Currently, -smp supports up to 7-levels topology hierarchy:
-drawers/books/sockets/dies/clusters/cores/threads.
Though no machine supports all these 7 levels yet, these 7 levels have
the strict containment relationship and together form the generic CPU
topology representation of QEMU.
Also, note that the maxcpus is calculated by multiplying all 7 levels:
maxcpus = drawers * books * sockets * dies * clusters *
cores * threads.
To cover this code path, it is necessary to test the full topology case
(with all 7 levels). This also helps to avoid introducing new issues by
further expanding the CPU topology in the future.
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Tested-by: Xiaoling Song <xiaoling.song@intel.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Message-ID: <20240308160148.3130837-12-zhao1.liu@linux.intel.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
