Anywhere we create a list of just one item or by prepending items
(typically because order doesn't matter), we can use
QAPI_LIST_PREPEND(). But places where we must keep the list in order
by appending remain open-coded until later patches.
Note that as a side effect, this also performs a cleanup of two minor
issues in qga/commands-posix.c: the old code was performing
new = g_malloc0(sizeof(*ret));
which 1) is confusing because you have to verify whether 'new' and
'ret' are variables with the same type, and 2) would conflict with C++
compilation (not an actual problem for this file, but makes
copy-and-paste harder).
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20201113011340.463563-5-eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
[Straightforward conflicts due to commit a8aa94b5f8 "qga: update
schema for guest-get-disks 'dependents' field" and commit a10b453a52
"target/mips: Move mips_cpu_add_definition() from helper.c to cpu.c"
resolved. Commit message tweaked.]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Change
Parameter 'mode' expects halt|powerdown|reboot
to
Parameter 'mode' expects 'halt', 'powerdown', or 'reboot'
for consistency with similar error messages elsewhere.
Cc: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20201113082626.2725812-9-armbru@redhat.com>
check_suspend_mode()'s error message
Parameter 'mode' expects GuestSuspendMode
makes no sense to users: GuestSuspendMode is a C enum. Fortunately,
it is unreachable. Replace it by abort().
Cc: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20201113082626.2725812-8-armbru@redhat.com>
The command lists all the physical disk drives. Unlike for Linux
partitions and virtual volumes are not listed.
Example output:
{
"return": [
{
"name": "\\\\.\\PhysicalDrive0",
"partition": false,
"address": {
"serial": "QM00001",
"bus-type": "sata",
...
},
"dependents": []
}
]
}
Signed-off-by: Tomáš Golembiovský <tgolembi@redhat.com>
Signed-off-by: Michael Roth <michael.roth@amd.com>
Add API and stubs for new guest-get-disks command.
The command guest-get-fsinfo can be used to list information about disks
and partitions but it is limited only to mounted disks with filesystem.
This new command should allow listing information about disks of the VM
regardles whether they are mounted or not. This can be usefull for
management applications for mapping virtualized devices or pass-through
devices to device names in the guest OS.
Signed-off-by: Tomáš Golembiovský <tgolembi@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Michael Roth <michael.roth@amd.com>
Simple unions are simpler than flat unions in the schema, but more
complicated in C and on the QMP wire: there's extra indirection in C
and extra nesting on the wire, both pointless. They should be avoided
in new code.
GuestDeviceId was recently added for guest-get-devices. Convert it to
a flat union.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Michael Roth <michael.roth@amd.com>
The Error ** argument must be NULL, &error_abort, &error_fatal, or a
pointer to a variable containing NULL. Passing an argument of the
latter kind twice without clearing it in between is wrong: if the
first call sets an error, it no longer points to NULL for the second
call.
qmp_guest_get_devices() is wrong that way: it calls error_setg() in a
loop.
If no iteration fails, the function returns a value and sets no error.
Okay.
If exactly one iteration fails, the function returns a value and sets
an error. Wrong.
If multiple iterations fail, the function trips error_setv()'s
assertion.
Fix it to return immediately on error.
Perhaps the failure to convert the driver version to UTF-8 should not
be an error. We could simply not report the botched version string
instead.
Drop a superfluous continue while there.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Michael Roth <michael.roth@amd.com>
guest-get-devices returns 'driver-date' as string in the format
YYYY-MM-DD. Goes back to recent commit 2e4211cee4 "qga: add command
guest-get-devices for reporting VirtIO devices".
We should avoid use of multiple encodings for the same kind of data.
Especially string encodings. Change it to return nanoseconds since
the epoch, like guest-get-time does.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Michael Roth <michael.roth@amd.com>
Member 'address' is union GuestDeviceAddress with a single branch
GuestDeviceAddressPCI, containing PCI vendor ID and device ID. This
is not a PCI address. Type GuestPCIAddress is. Messed up in recent
commit 2e4211cee4 "qga: add command guest-get-devices for reporting
VirtIO devices".
Rename type GuestDeviceAddressPCI to GuestDeviceIdPCI, type
GuestDeviceAddress to GuestDeviceId, and member 'address' to 'id'.
Document the member properly while there.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Michael Roth <michael.roth@amd.com>
When compiling QEMU with MSYS2 on Windows, there is currently the
following error:
../qga/commands-win32.c:62:24: error: redundant redeclaration of
'CM_Get_DevNode_PropertyW' [-Werror=redundant-decls]
62 | CMAPI CONFIGRET WINAPI CM_Get_DevNode_PropertyW(
| ^~~~~~~~~~~~~~~~~~~~~~~~
In file included from ../qga/commands-win32.c:26:
C:/tools/msys64/mingw64/x86_64-w64-mingw32/include/cfgmgr32.h:840:26: note:
previous declaration of 'CM_Get_DevNode_PropertyW' was here
840 | CMAPI CONFIGRET WINAPI CM_Get_DevNode_PropertyW(DEVINST dnDevInst,
const DEVPROPKEY *PropertyKey, DEVPROPTYPE *PropertyType, PBYTE PropertyBuffer,
PULONG PropertyBufferSize, ULONG ulFlags);
Seems like this protype is sometimes available in the cfgmgr32.h
header, and sometimes not. Let's silence the compiler warning here
to let the build pass with -Werror, too.
Message-Id: <20200915114757.55635-1-thuth@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Add command for reporting devices on Windows guest. The intent is not so
much to report the devices but more importantly the driver (and its
version) that is assigned to the device. This gives caller the
information whether VirtIO drivers are installed and/or whether
inadequate driver is used on a device (e.g. QXL device with base VGA
driver).
Example:
[
{
"driver-date": "2019-08-12",
"driver-name": "Red Hat VirtIO SCSI controller",
"driver-version": "100.80.104.17300",
"address": {
"type": "pci",
"data": {
"device-id": 4162,
"vendor-id": 6900
}
}
},
...
]
Signed-off-by: Tomáš Golembiovský <tgolembi@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
*remove redundant glib autoptr declaration for GuestDeviceInfo
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
This patch handles the case where unmounted volumes exist,
where in that case GetVolumePathNamesForVolumeName returns
empty path, GetVolumeInformation will use the current working
directory instead.
This patch fixes the issue by opening a handle to the volumes,
and using GetVolumeInformationByHandleW instead.
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=1746667
Signed-off-by: Basil Salman <bsalman@redhat.com>
Signed-off-by: Basil Salman <basil@daynix.com>
*fix crash when guest_build_fsinfo() sets errp multiple times
*make new error message more distinct from existing ones
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
When all we do with an Error we receive into a local variable is
propagating to somewhere else, we can just as well receive it there
right away. Convert
if (!foo(..., &err)) {
...
error_propagate(errp, err);
...
return ...
}
to
if (!foo(..., errp)) {
...
...
return ...
}
where nothing else needs @err. Coccinelle script:
@rule1 forall@
identifier fun, err, errp, lbl;
expression list args, args2;
binary operator op;
constant c1, c2;
symbol false;
@@
if (
(
- fun(args, &err, args2)
+ fun(args, errp, args2)
|
- !fun(args, &err, args2)
+ !fun(args, errp, args2)
|
- fun(args, &err, args2) op c1
+ fun(args, errp, args2) op c1
)
)
{
... when != err
when != lbl:
when strict
- error_propagate(errp, err);
... when != err
(
return;
|
return c2;
|
return false;
)
}
@rule2 forall@
identifier fun, err, errp, lbl;
expression list args, args2;
expression var;
binary operator op;
constant c1, c2;
symbol false;
@@
- var = fun(args, &err, args2);
+ var = fun(args, errp, args2);
... when != err
if (
(
var
|
!var
|
var op c1
)
)
{
... when != err
when != lbl:
when strict
- error_propagate(errp, err);
... when != err
(
return;
|
return c2;
|
return false;
|
return var;
)
}
@depends on rule1 || rule2@
identifier err;
@@
- Error *err = NULL;
... when != err
Not exactly elegant, I'm afraid.
The "when != lbl:" is necessary to avoid transforming
if (fun(args, &err)) {
goto out
}
...
out:
error_propagate(errp, err);
even though other paths to label out still need the error_propagate().
For an actual example, see sclp_realize().
Without the "when strict", Coccinelle transforms vfio_msix_setup(),
incorrectly. I don't know what exactly "when strict" does, only that
it helps here.
The match of return is narrower than what I want, but I can't figure
out how to express "return where the operand doesn't use @err". For
an example where it's too narrow, see vfio_intx_enable().
Silently fails to convert hw/arm/armsse.c, because Coccinelle gets
confused by ARMSSE being used both as typedef and function-like macro
there. Converted manually.
Line breaks tidied up manually. One nested declaration of @local_err
deleted manually. Preexisting unwanted blank line dropped in
hw/riscv/sifive_e.c.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20200707160613.848843-35-armbru@redhat.com>
Replace
error_setg(&err, ...);
error_propagate(errp, err);
by
error_setg(errp, ...);
Related pattern:
if (...) {
error_setg(&err, ...);
goto out;
}
...
out:
error_propagate(errp, err);
return;
When all paths to label out are that way, replace by
if (...) {
error_setg(errp, ...);
return;
}
and delete the label along with the error_propagate().
When we have at most one other path that actually needs to propagate,
and maybe one at the end that where propagation is unnecessary, e.g.
foo(..., &err);
if (err) {
goto out;
}
...
bar(..., &err);
out:
error_propagate(errp, err);
return;
move the error_propagate() to where it's needed, like
if (...) {
foo(..., &err);
error_propagate(errp, err);
return;
}
...
bar(..., errp);
return;
and transform the error_setg() as above.
In some places, the transformation results in obviously unnecessary
error_propagate(). The next few commits will eliminate them.
Bonus: the elimination of gotos will make later patches in this series
easier to review.
Candidates for conversion tracked down with this Coccinelle script:
@@
identifier err, errp;
expression list args;
@@
- error_setg(&err, args);
+ error_setg(errp, args);
... when != err
error_propagate(errp, err);
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20200707160613.848843-34-armbru@redhat.com>
The Error ** argument must be NULL, &error_abort, &error_fatal, or a
pointer to a variable containing NULL. Passing an argument of the
latter kind twice without clearing it in between is wrong: if the
first call sets an error, it no longer points to NULL for the second
qmp_guest_suspend_disk() and qmp_guest_suspend_ram() pass @local_err
first to check_suspend_mode(), then to acquire_privilege(), then to
execute_async(). Continuing after errors here can only end in tears.
For instance, we risk tripping error_setv()'s assertion.
Fixes: aa59637ea1
Fixes: f54603b6aa
Cc: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20200422130719.28225-15-armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Extract the common code shared by both POSIX/Win32 implementations.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
As we are going to reuse this method, declare it in common
header.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
As noted by Daniel Berrangé in [*], the fix from commit 807e2b6fce
which replaced malloc() by try_malloc() is not enough, the process
can still run out of memory a few line later:
346 buf = g_try_malloc0(count + 1);
347 if (!buf) {
348 error_setg(errp,
349 "failed to allocate sufficient memory "
350 "to complete the requested service");
351 return NULL;
352 }
353 is_ok = ReadFile(fh, buf, count, &read_count, NULL);
354 if (!is_ok) {
355 error_setg_win32(errp, GetLastError(), "failed to read file");
356 slog("guest-file-read failed, handle %" PRId64, handle);
357 } else {
358 buf[read_count] = 0;
359 read_data = g_new0(GuestFileRead, 1);
^^^^^^
Instead we are going to put a low hard limit on 'count' in the next
commits. This reverts commit 807e2b6fce.
[*] https://lists.gnu.org/archive/html/qemu-devel/2018-06/msg03471.html
Suggested-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
guest-file-read command is currently implemented to read from a
file handle count number of bytes. when executed with a very large count number
qemu-ga crashes.
after some digging turns out that qemu-ga crashes after trying to allocate
a buffer large enough to save the data read in it, the buffer was allocated using
g_malloc0 which is not fail safe, and results a crash in case of failure.
g_malloc0 was replaced with g_try_malloc0() which returns NULL on failure,
A check was added for that case in order to prevent qemu-ga from crashing
and to send a response to the qemu-ga client accordingly.
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=1594054
Signed-off-by: Basil Salman <basil@daynix.com>
Reported-by: Fakhri Zulkifli <mohdfakhrizulkifli@gmail.com>
Cc: qemu-stable@nongnu.org
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Use error_setg_win32() which adds a hint similar to strerror(errno)).
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200228100726.8414-4-philmd@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20191205174635.18758-13-vsementsov@virtuozzo.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Memory block commands are only supported for linux with sysfs,
"guest-get-memory-block-info" was not in blacklist for other
cases.
Reported on:
https://bugzilla.redhat.com/show_bug.cgi?id=1751431
Signed-off-by: Basil Salman <bsalman@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Network interface name is fetched as an encoded WCHAR array, (wide
character), then it is decoded using the guest's CP_ACP Windows code
page, which is the default code page as configure in the guest's
Windows, then it is returned as a byte array, (char array).
As stated in the BZ#1733165, when renaming a network interface to a
Chinese name and invoking this command, the returned name field has
the (\ufffd) value for each Chinese character the name had, this
value is an indication that the code page does not have the decoding
information for the given character.
This bug is a result of using the CP_ACP code page for decoding which
is an interchangeable code page, instead CP_UTF8 code page should be
used for decoding the network interface's name.
https://bugzilla.redhat.com/show_bug.cgi?id=1733165
Signed-off-by: Bishara AbuHattoum <bishara@daynix.com>
Cc: qemu-stable@nongnu.org
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
The win2qemu[] is supposed to be the conversion table to convert between
STORAGE_BUS_TYPE in Windows SDK and GuestDiskBusType in qga.
But it was incorrectly written that it forces to set a GuestDiskBusType
value to STORAGE_BUS_TYPE, which generates an enum conversion warning in clang.
Suggested-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Cao Jiaxi <driver1998@foxmail.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 20190503003650.10137-1-driver1998@foxmail.com
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Windows QEMU guest agent erroneously tries to collect PCI information
directly from the physical drive. However, windows stores SCSI/IDE information
with the drive and PCI information with the underlying storage controller
This changes get_pci_info to use the physical drive's underlying storage
controller to get PCI information.
* Additionally Fixes incorrect size being passed to DeviceIoControl
when getting volume extents. Can occasionally crash the guest agent
Signed-off-by: Matt Hines <mhines@scalecomputing.com>
*fix up some checkpatch warnings
*fix domain reporting and add some sanity checks for debug
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Since Windows Server 2016, Microsoft stopped upgrading the major and minor
versions of their new Windows Server product, so, the current functionality
of checking major and minor version numbers to determine the Windows Server
version wont work as expected.
The implemented solution here is to use the build number in addition to the
major and minor version numbers of the product to determine the Windows
Server product version.
The final build number of Windows Server 2016 is 14939, and
the final build number of Windows Server 2019 is 17764, so any Windows
Server product that has the major version of 10 and minor version of 0
with a build number lower or equal to 14939 will resemble 2016 and if the
build number is lower or equal to 17763 will resemble 2019.
Reference:
https://techcommunity.microsoft.com/t5/Windows-Server-Insiders/Windows-Server-2019-version-info/m-p/293112/highlight/true#M859
Signed-off-by: Bishara AbuHattoum <bishara@daynix.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Building QGA for XP seems possible so far: the dependency on
libqemuutil.a implies building qemu-thread-win32.c, which requires
Vista API since commit 12f8def0 (v2.9). But qemu-thread isn't being
used in QGA, the resulting binary may still work on XP. XP is no
longer supported for the past 4.5y, it's time to drop support for it.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20181122110039.15972-5-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Both qemu & qga build with Vista API by default already, by defining
_WIN32_WINNT 0x0600. Set it globally in osdep.h instead.
This replaces WINVER by _WIN32_WINNT in osdep.h. WINVER doesn't seem
to be really useful these days.
(see also https://blogs.msdn.microsoft.com/oldnewthing/20070411-00/?p=27283)
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20181122110039.15972-4-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Introduced in commit b1ba8890e6, vol_h
handle should be closed, and "out" cleanup should be done after
DeviceIoControl() fails.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Li Qiang <liq3ea@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
It was not obvious what exactly the cryptic string copying does to the
GUID. This change makes the intent clearer.
Signed-off-by: Tomáš Golembiovský <tgolembi@redhat.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Report device UNC of the disk. It is reported as "\\.\PhysicalDriveX".
Signed-off-by: Tomáš Golembiovský <tgolembi@redhat.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Probe the volume for disk extents and return list of all disks.
Originally only first disk of composite volume was returned.
Note that the patch changes get_pci_info() from one state of brokenness
into a different state of brokenness. In other words it still does not do
what it's supposed to do (see comment in code). If anyone knows how to
fix it, please step in.
Signed-off-by: Tomáš Golembiovský <tgolembi@redhat.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Refactor building of disk info into a function that builds the list and
a function that returns infor for single disk. This will be used in
future commit that will handle multi-disk volumes.
Signed-off-by: Tomáš Golembiovský <tgolembi@redhat.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Tomáš Golembiovský <tgolembi@redhat.com>
*coding style fix-ups (declarations at beginning of block)
*improve readability for user-visible errors
*cover additional edge-cases with debug statements
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Refactor code that queries bus type to be more generic. The function
get_disk_bus_type() has been renamed to build_guest_disk_info().
Following commit(s) will extend this function.
Signed-off-by: Tomáš Golembiovský <tgolembi@redhat.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
The windows code generaly lacks debug information (compared to posix
code). This patch adds some related to HW info in guest-get-fsinfo
command.
Signed-off-by: Tomáš Golembiovský <tgolembi@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
The call to SetupDiGetDeviceRegistryProperty might fail because the
value doesn't exist in the registry, in this case we shouldn't exit from
the loop but instead continue to look for other available values in the
registry and set this value as unavailable (-1).
Signed-off-by: Sameeh Jubran <sjubran@redhat.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Tomáš Golembiovský <tgolembi@redhat.com>
*squash in fix for when get_pci_info() returns NULL pci_controller field
*fix handling for error_set() cases in get_pci_info(), not just NULL return
*force all -1 PCI addr fields if any single one of them isn't found
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
The fsinfo command is currently implemented for Windows only and it's disk
parameter can be enabled by adding the define "CONFIG_QGA_NTDDSCSI" to the qga
code. When enabled and executed the qemu-ga crashed with the following message:
------------------------------------------------
File qapi/qapi-visit-core.c, Line 49
Expression: !(v->type & VISITOR_OUTPUT) || *obj)
------------------------------------------------
After some digging, turns out that the GuestPCIAddress is null and the
qapi visitor doesn't like that, so we can always allocate it instead and
initiate all it's members to -1.
Signed-off-by: Sameeh Jubran <sjubran@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Tomáš Golembiovský <tgolembi@redhat.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
This patch add support for freeze specified fs.
The valid mountpoints list member are [1]:
The path of a mounted folder, for example, Y:\MountX\
A drive letter, for example, D:\
A volume GUID path of the form \\?\Volume{GUID}\,
where GUID identifies the volume
A UNC path that specifies a remote file share,
for example, \\Clusterx\Share1\
[1] https://docs.microsoft.com/en-us/windows/desktop/api/vsbackup/nf-vsbackup-ivssbackupcomponents-addtosnapshotset
Cc: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Chen Hanxiao <chenhanxiao@gmail.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Currently, the win32 port of QEMU Guest Agent does not properly handle Unicode
paths. The JSON decoder produces a valid UTF-8 path string, but this is passed
directly to CreateFileA, which is expecting an ANSI string and not UTF-8. This
leads to mangled filenames.
This patch follows the example of qmp_guest_set_user_password() and uses
g_utf8_to_utf16() to convert the string to UTF-16 and calls CreateFileW()
explicitly.
Signed-off-by: Jonathon Reinhart <jreinhart@cc-sw.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
The defrag.exe tool which is used for executing the fstrim command
on Windows doesn't support retrim for OSes lower than Win8. This
commit handles this case and returns a suitable error.
Output of fstrim before this commit:
{"execute":"guest-fstrim"}
{"return": {"paths": [{"path": "C:\\", "error": "An invalid command line option
was specified. (0x89000008)"}, {"path": "F:\\", "error": "An invalid command
line option was specified. (0x89000008)"}, {"path": "S:\\", "error": "An
invalid command line option was specified. (0x89000008)"}]}}
Reported on:
https://bugzilla.redhat.com/show_bug.cgi?id=1594113
Signed-off-by: Sameeh Jubran <sjubran@redhat.com>
* use alternative version query code proposed by Sameeh
* fix up version check logic
* avoid CamelCase variable names when possible
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
This patch adds support for getting the usage of
windows driver path.
The usage of fs stored as used_bytes and total_bytes.
Cc: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Chen Hanxiao <chenhanxiao@gmail.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
While reading file content via 'guest-file-read' command,
'qmp_guest_file_read' routine allocates buffer of count+1
bytes. It could overflow for large values of 'count'.
Add check to avoid it.
Reported-by: Fakhri Zulkifli <mohdfakhrizulkifli@gmail.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Cc: qemu-stable@nongnu.org
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
When pulling in headers that are in the same directory as the C file (as
opposed to one in include/), we should use its relative path, without a
directory.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Move qapi-schema.json to qapi/, so it's next to its modules, and all
files get generated to qapi/, not just the ones generated for modules.
Consistently name the generated files qapi-MODULE.EXT:
qmp-commands.[ch] become qapi-commands.[ch], qapi-event.[ch] become
qapi-events.[ch], and qmp-introspect.[ch] become qapi-introspect.[ch].
This gets rid of the temporary hacks in scripts/qapi/commands.py,
scripts/qapi/events.py, and scripts/qapi/common.py.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180211093607.27351-28-armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
[eblake: Fix trailing dot in tpm.c, undo temporary hack for OSX toolchain]
Signed-off-by: Eric Blake <eblake@redhat.com>
This cleanup makes the number of objects depending on qapi/error.h
drop from 1910 (out of 4743) to 1612 in my "build everything" tree.
While there, separate #include from file comment with a blank line,
and drop a useless comment on why qemu/osdep.h is included first.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180201111846.21846-5-armbru@redhat.com>
[Semantic conflict with commit 34e304e975 resolved, OSX breakage fixed]
The data obtained by GetIfEntry is 32 bits, and it may overflow. Thus
using GetIfEntry2 instead of GetIfEntry.
Signed-off-by: ZhiPeng Lu <lu.zhipeng@zte.com.cn>
*avoid CamelCase variable names
*update field names for MIB_IFROW -> MIB_IF_ROW2
*dynamically probe for GetIfIndex2 to deal with older OSs
*check return value from get_interface_index
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
we can get the network interface statistics inside a virtual machine by
guest-network-get-interfaces command. it is very useful for us tomonitor
and analyze network traffic.
Signed-off-by: ZhiPeng Lu <lu.zhipeng@zte.com.cn>
* don't rely on sizeof(wchar[]) for wchar[] indexing
* avoid camelCase variable names
* fix up getline() usage
* condensed commit subject line
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
At the moment, Windows libraries don't provide a way to access
RTC, so, a workaround is to use the Windows w32tm command to
resync the time.
Related bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1183874
Signed-off-by: Bishara AbuHattoum <bishara@daynix.com>
Reviewed-by: Sameeh Jubran <sameeh@daynix.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
