The dump_mmu() function does a ldl_phys() at the start, but
then never uses the value it loads at all. Remove the
unused code.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-id: 20190801183012.17564-7-peter.maydell@linaro.org
Convert the mmu_probe() function to using address_space_ldl()
rather than ldl_phys(), so we can explicitly detect memory
transaction failures.
This makes no practical difference at the moment, because
ldl_phys() will return 0 on a transaction failure, and we
treat transaction failures and 0 PDEs identically. However
the spec says that MMU probe operations are supposed to
update the fault status registers, and if we ever implement
that we'll want to distinguish the difference. For the
moment, just add a TODO comment about the bug.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-id: 20190801183012.17564-6-peter.maydell@linaro.org
Currently we use the ldl_phys() function to read page table entries.
With the unassigned_access hook in place, if these hit an unassigned
area of memory then the hook will cause us to wrongly generate
an exception with a fault address matching the address of the
page table entry.
Change to using address_space_ldl() so we can detect and correctly
handle bus errors and give them their correct behaviour of
causing a translation error with a suitable fault status register.
Note that this won't actually take effect until we switch the
over to using the do_translation_failed hook.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-id: 20190801183012.17564-5-peter.maydell@linaro.org
This bit configures endianness of PCI MMIO devices. It is used by
Solaris and OpenBSD sunhme drivers.
Tested working on OpenBSD.
Unfortunately Solaris 10 had a unrelated keyboard issue blocking
testing... another inch towards Solaris 10 on SPARC64 =)
Signed-off-by: Tony Nguyen <tony.nguyen@bt.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <3c8d5181a584f1b3712d3d8d66801b13cecb4b88.1566466906.git.tony.nguyen@bt.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Append MemTxAttrs to interfaces so we can pass along up coming Invert
Endian TTE bit on SPARC64.
Signed-off-by: Tony Nguyen <tony.nguyen@bt.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <f8fcc3138570c460ef289a6b34ba7715ba36f99e.1566466906.git.tony.nguyen@bt.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Cleanup in the boilerplate that each target must define.
Replace sparc_env_get_cpu with env_archcpu. The combination
CPU(sparc_env_get_cpu) should have used ENV_GET_CPU to begin;
use env_cpu now.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The various dump_mmu() take an fprintf()-like callback and a FILE * to
pass to it, and so do their helper functions. Passing around callback
and argument is rather tiresome.
Most dump_mmu() are called only by the target's hmp_info_tlb(). These
all pass monitor_printf() cast to fprintf_function and the current
monitor cast to FILE *.
SPARC's dump_mmu() gets also called from target/sparc/ldst_helper.c a
few times #ifdef DEBUG_MMU. These calls pass fprintf() and stdout.
The type-punning is technically undefined behaviour, but works in
practice. Clean up: drop the callback, and call qemu_printf()
instead.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20190417191805.28198-11-armbru@redhat.com>
The MC68040 MMU provides the size of the access that
triggers the page fault.
This size is set in the Special Status Word which
is written in the stack frame of the access fault
exception.
So we need the size in m68k_cpu_unassigned_access() and
m68k_cpu_handle_mmu_fault().
To be able to do that, this patch modifies the prototype of
handle_mmu_fault handler, tlb_fill() and probe_write().
do_unassigned_access() already includes a size parameter.
This patch also updates handle_mmu_fault handlers and
tlb_fill() of all targets (only parameter, no code change).
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20180118193846.24953-2-laurent@vivier.eu>
This code is preventing the MMU debug code from displaying virtual
mappings of IO devices (anything that is not located in the RAM).
Before this patch, Qemu would output 0xffffffffffffffff (-1) as the
physical address corresponding to an IO device virtual address.
With this patch the intended physical address is displayed.
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
In the user-mode-only version of sparc_cpu_handle_mmu_fault(),
we must save the fault address for a data fault into the CPU
state's mmu registers, because the code in linux-user/main.c
expects to find it there in order to populate the si_addr
field of the guest siginfo.
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Riku Voipio <riku.voipio@linaro.org>
Make CPUSPARCState::def embedded so it would be allocated as part
of cpu instance and we won't have to worry about cleaning def pointer
up mannualy on cpu destruction.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1503592308-93913-4-git-send-email-imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
We've currently got 18 architectures in QEMU, and thus 18 target-xxx
folders in the root folder of the QEMU source tree. More architectures
(e.g. RISC-V, AVR) are likely to be included soon, too, so the main
folder of the QEMU sources slowly gets quite overcrowded with the
target-xxx folders.
To disburden the main folder a little bit, let's move the target-xxx
folders into a dedicated target/ folder, so that target-xxx/ simply
becomes target/xxx/ instead.
Acked-by: Laurent Vivier <laurent@vivier.eu> [m68k part]
Acked-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de> [tricore part]
Acked-by: Michael Walle <michael@walle.cc> [lm32 part]
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com> [s390x part]
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com> [s390x part]
Acked-by: Eduardo Habkost <ehabkost@redhat.com> [i386 part]
Acked-by: Artyom Tarasenko <atar4qemu@gmail.com> [sparc part]
Acked-by: Richard Henderson <rth@twiddle.net> [alpha part]
Acked-by: Max Filippov <jcmvbkbc@gmail.com> [xtensa part]
Reviewed-by: David Gibson <david@gibson.dropbear.id.au> [ppc part]
Acked-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com> [crisµblaze part]
Acked-by: Guan Xuetao <gxt@mprc.pku.edu.cn> [unicore32 part]
Signed-off-by: Thomas Huth <thuth@redhat.com>
