This is in preparation for adding configuration space accessors which accept
PCIDevice as a parameter.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Make sure that the standard DMA interrupt status bits reflect any changes made
to the UDMA interrupt status bits. The CMD646U2 datasheet claims that these
bits are equivalent, and they must be synchronised for guests that manipulate
both registers.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Currently, the ioapic device can not be found in a qtest environment
when requesting "irq_interrupt_in ioapic" via the qtest socket.
By mirroring how the ioapic is added in i44ofx (hw/i440/pc_piix.c),
as a child of "q35," the device is able to be seen by qtest.
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
PIO commands should put a PIO Setup FIS in the receive area when data
transfer ends. Currently QEMU does not do this and only places the
D2H FIS at the end of the operation.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
AHCI has code to fill in the D2H FIS trigger the IRQ all over the place.
Centralize this in a single cmd_done callback by generalizing the existing
async_cmd_done callback.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This will provide a hook for sending the result of the command via the
FIS receive area.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
These are defined twice, just use one set consistently.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
They are not used by AHCI, and should not be even available there.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
It is now called only after the set_inactive callback. Put the two together.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Similar to the case removed in commit 69c38b8 (ide/core: Remove explicit
setting of BM_STATUS_INT, 2011-05-19), the only remaining use of
add_status(..., BM_STATUS_INT) is for short PRDs. The flag should
not be raised in this case.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Make it optional and prepare for the next patches.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Drop the unused return value and make the callback optional.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Drop the unused return value.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Drop the unused return value and make the callback optional.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Drop the unused return value and make the callback optional.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This ensures that operations are completed after a reset
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5w3j
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/kevin/tags/for-upstream' into staging
Block patches
# gpg: Signature made Fri 15 Aug 2014 14:07:42 BST using RSA key ID C88F2FD6
# gpg: Good signature from "Kevin Wolf <kwolf@redhat.com>"
* remotes/kevin/tags/for-upstream: (59 commits)
block: Catch !bs->drv in bdrv_check()
iotests: Add test for image header overlap
qcow2: Catch !*host_offset for data allocation
qcow2: Return useful error code in refcount_init()
mirror: Handle failure for potentially large allocations
vpc: Handle failure for potentially large allocations
vmdk: Handle failure for potentially large allocations
vhdx: Handle failure for potentially large allocations
vdi: Handle failure for potentially large allocations
rbd: Handle failure for potentially large allocations
raw-win32: Handle failure for potentially large allocations
raw-posix: Handle failure for potentially large allocations
qed: Handle failure for potentially large allocations
qcow2: Handle failure for potentially large allocations
qcow1: Handle failure for potentially large allocations
parallels: Handle failure for potentially large allocations
nfs: Handle failure for potentially large allocations
iscsi: Handle failure for potentially large allocations
dmg: Handle failure for potentially large allocations
curl: Handle failure for potentially large allocations
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add some trace events to virtio-rng for easier debugging
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Reviewed-by: Amos Kong <akong@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This fixes a warning from smatch (static code analyser).
Fix also the comment with the renamed source file name.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
hw/timer/tusb6010.c | 3 ---
include/hw/usb.h | 7 ++++++-
2 files changed, 6 insertions(+), 4 deletions(-)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The symbol TIMER_MAX used in imx_epit.c and imx_gpt.c
clashes with system symbol with the same name. Because
all qemu source files includes qemu-common.h which, in
turn, includes limits.h, which is not unusual to define
it. Rename local symbol to have a reasonable prefix.
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Commit 40509f7f added a test to avoid updating KVM MSI routes when the
MSIMessage is unchanged and f4d45d47 switched to relying on this
rather than doing our own comparison. Our cached msg is effectively
unused now. Remove it.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
When new MSI-X vectors are enabled we need to disable MSI-X and
re-enable it with the correct number of vectors. That means we need
to reprogram the eventfd triggers for each vector. Prior to f4d45d47
vector->use tracked whether a vector was masked or unmasked and we
could always pick the KVM path when available for unmasked vectors.
Now vfio doesn't track mask state itself and vector->use and virq
remains configured even for masked vectors. Therefore we need to ask
the MSI-X code whether a vector is masked in order to select the
correct signaling path. As noted in the comment, MSI relies on
hardware to handle masking.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Cc: qemu-stable@nongnu.org # QEMU 2.1
This dma_memory_read was giving too big a size when begin was non-zero.
This could cause segfaults in some circumstances. Fix.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add some spacing and zeros to make it easier to read and
modify the map. This patch has no functional changes. The
review looks ugly, but it's actually pretty easy to confirm
all the addresses are as they should be - thanks to the new
formatting ;-)
Signed-off-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The code in do_cpu_reset() correctly handled AArch64 CPUs
when running Linux kernels, but was missing code in the
branch of the if() that deals with loading ELF files.
Correctly jump to the ELF entry point on reset rather than
leaving the reset PC at zero.
Reported-by: Christopher Covington <cov@codeaurora.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Christopher Covington <cov@codeaurora.org>
Cc: qemu-stable@nongnu.org
Under recommendation from Luiz Capitulino, we are changing
the error_set calls to error_setg while we are fixing up
the error handling pathways of virtio-rng.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
This patch pushes the error-checking forward and the virtio
initialization backward in the device realization function
in order to prevent memory leaks for hot plug scenarios.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
qemu side patch to support xen HVM direct kernel boot:
if -kernel exists, calls xen_load_linux(), which will read kernel/initrd
and add a linuxboot.bin or multiboot.bin option rom. The
linuxboot.bin/multiboot.bin will load kernel/initrd and jump to execute
kernel directly. It's working when xen uses seabios.
During this work, found the 'kvmvapic' is in option_rom list, it should
not be there in xen case. Set s->vapic_control = 0 in xen_apic_realize()
to handle that.
Signed-off-by: Chunyan Liu <cyliu@suse.com>
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
pl031's base address should be 0x9010000, not 0x90010000, otherwise
it sits in ram when configuring a guest with greater than 1G.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
- Tweak error message for legacy machine type:
Basically if table size exceeds the limits we set all
bets are off for migration: e.g. it can start failing even
within given qemu minor version simply because of a bugfix.
- Increase table size to 128k.
- Make sure we notice it long before we start getting close to the
128k limit: warn at 64k.
- Don't fail if we exceed the limit: most people don't care about
migration, even less people care about cross version miration.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
This patch avoids that similar changes break QEMU again in the future.
QEMU will now hard-code 64k as the maximum ACPI table size, which
(despite being an order of magnitude smaller than 640k) should be enough
for everyone.
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Fixes migration regression from QEMU-1.7 to a newer QEMUs.
SSDT table size in QEMU-1.7 doesn't change regardless of
a number of PCI bridge devices present at startup.
However in QEMU-2.0 since addition of hotplug on PCI bridges,
each PCI bridge adds ~1875 bytes to SSDT table, including
pc-i440fx-1.7 machine type where PCI bridge hotplug disabled
via compat property.
It breaks migration from "QEMU-1.7" to "QEMU-2.[01] -M pc-i440fx-1.7"
since RAMBlock size of ACPI tables on target becomes larger
then on source and migration fails with:
"Length mismatch: /rom@etc/acpi/tables: 2000 in != 3000"
error.
Fix this by generating AML only for PCI0 bus if
hotplug on PCI bridges is disabled and preserves PCI brigde
description in AML as it was done in QEMU-1.7 for pc-i440fx-1.7.
It will help to maintain size of SSDT static regardless of
number of PCI bridges on startup for pc-i440fx-1.7 machine type.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Changing the ACPI table size causes migration to break, and the memory
hotplug work opened our eyes on how horribly we were breaking things in
2.0 already.
The ACPI table size is rounded to the next 4k, which one would think
gives some headroom. In practice this is not the case, because the user
can control the ACPI table size (each CPU adds 97 bytes to the SSDT and
8 to the MADT) and so some "-smp" values will break the 4k boundary and
fail to migrate. Similarly, PCI bridges add ~1870 bytes to the SSDT.
This patch concerns itself with fixing migration from QEMU 2.0. It
computes the payload size of QEMU 2.0 and always uses that one.
The previous patch shrunk the ACPI tables enough that the QEMU 2.0 size
should always be enough; non-AML tables can change depending on the
configuration (especially MADT, SRAT, HPET) but they remain the same
between QEMU 2.0 and 2.1, so we only compute our padding based on the
sizes of the SSDT and DSDT.
Migration from QEMU 1.7 should work for guests that have a number of CPUs
other than 12, 13, 14, 54, 55, 56, 97, 98, 139, 140. It was already
broken from QEMU 1.7 to QEMU 2.0 in the same way, though.
Even with this patch, QEMU 1.7 and 2.0 have two different ideas of
"-M pc-i440fx-2.0" when there are PCI bridges. Igor sent a patch to
adopt the QEMU 1.7 definition. I think distributions should apply
it if they move directly from QEMU 1.7 to 2.1+ without ever packaging
version 2.0.
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This replaces the _PRT constant with a method that computes it.
The problem is that the DSDT+SSDT have grown from 2.0 to 2.1,
enough to cross the 8k barrier (we align the ACPI tables to 4k
before putting them in fw_cfg). This causes problems with
migration and the pc-i440fx-2.0 machine type.
The solution to the problem is to hardcode 64k as the limit,
but this doesn't solve the bug with pc-i440fx-2.0. The fix will be
for QEMU 2.1 to use exactly the same size as QEMU 2.0 for the
ACPI tables. First, however, we must make the actual AML
equal or smaller; to do this, rewrite _PRT in a way that saves
over 1k of bytecode.
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reason: we don't want commit to that interface yet. Possibly
the implementation will be switched over to use fsdev.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The VMStateDescription for the imx_ccm device was missing its
terminator. Found by static search of the codebase using
a regex based on one suggested by Ian Jackson:
pcregrep -rMi '(?s)VMStateField(?:(?!END_OF_LIST).)*?;' $(git grep -l 'VMStateField\[\]')
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Cc: qemu-stable@nongnu.org
"vmstate_xhci_event" was introduced in commit 37352df3 ("xhci: add live
migration support"), and first released in v1.6.0. The field list in this
VMSD is not terminated with the VMSTATE_END_OF_LIST() macro.
During normal use (ie. migration), the issue is practically invisible,
because the "vmstate_xhci_event" object (with the unterminated field list)
is only ever referenced -- via "vmstate_xhci_intr" -- if xhci_er_full()
returns true, for the "ev_buffer" test. Since that field_exists() check
(apparently) almost always returns false, we almost never traverse
"vmstate_xhci_event" during migration, which hides the bug.
However, Amit's vmstate checker forces recursion into this VMSD as well,
and the lack of VMSTATE_END_OF_LIST() breaks the field list terminator
check (field->name != NULL) in dump_vmstate_vmsd(). The result is
undefined behavior, which in my case translates to infinite recursion
(because the loop happens to overflow into "vmstate_xhci_intr", which then
links back to "vmstate_xhci_event").
Add the missing terminator.
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Only a single bug fix to make -mem-path only affect RAM regions.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=KL8S
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/agraf/tags/signed-ppc-for-upstream' into staging
Patch queue for ppc - 2014-07-22
Only a single bug fix to make -mem-path only affect RAM regions.
# gpg: Signature made Tue 22 Jul 2014 16:38:04 BST using RSA key ID 03FEDC60
# gpg: Can't check signature: public key not found
* remotes/agraf/tags/signed-ppc-for-upstream:
ppc: fix -mem-path failure
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
commit e938ba0c tried to enable -mem-path for ppc but breaked some ppc
boards.
The problems are:
1. it fails when allocating memory for rom, sram whose sizes are less
than huge page size:
./ppc-softmmu/qemu-system-ppc -m 512 -mem-path /hugepages/ \
-kernel /home/hutao/Downloads/vmlinux-ppc -initrd \
/home/hutao/Downloads/initrd-ppc.gz
qemu-system-ppc: /mnt/data/projects/qemu/exec.c:1184: qemu_ram_set_idstr: Assertion `new_block' failed.
2. if there is a numa node backed by memory backend object, qemu fails
with message:
./ppc-softmmu/qemu-system-ppc -m 512 \
-object memory-backend-file,size=512M,mem-path=/hugepages,id=f0 \
-numa node,nodeid=0,memdev=f0 \
-kernel /home/hutao/Downloads/vmlinux-ppc \
-initrd /home/hutao/Downloads/initrd-ppc.gz
qemu-system-ppc: memory backend f0 is used multiple times. Each -numa option must use a different memdev value.
This patch does following:
1. replaces memory_region_allocate_system_memory() with
memory_region_init_ram() for rom, sram. Then only system memory
is backed by hugepages when specifying mem-path.
2. for memory banks, allocates all ram with
one memory_region_allocate_system_memory(), and use
memory_region_init_alias() to initialize memory banks.
Tested machines: default(g3beige), mac99, taihu, bamboo, ref405ep.
Signed-off-by: Hu Tao <hutao@cn.fujitsu.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
If a negative integer is used for the max_bytes parameter, QEMU currently
calls abort() and leaves behind a core dump. This patch replaces the
abort with a simple error message to make the reason for the termination
clearer. This also ensures device-hotplug with invalid input doesn't
cause qemu to quit.
There is an underlying insufficiency in the parameter parsing code of QEMU
that renders it unable to reject negative values for unsigned properties,
thus the error message "a non-negative integer below 2^63" is the most
user-friendly and correct message we can give until the underlying
insufficiency is corrected.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Replaced '_' with '-' to comply with QOM guidelines.
Made the conversion from command line to QMP in vl.c.
Signed-off-by: Marcel Apfelbaum <marcel.a@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
