They're actually more commonly used than the helper without _under_bus, because
most callers do have the pci bus on hand. After exporting we can switch a lot
of the call sites to use these two helpers.
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20211028043129.38871-3-peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Recent Linux kernels are accessing the PCI device in slot 0 that
represents the PCI host bridge. This causes ppc4xx_pci_map_irq()
to return -1 which causes an assert() later:
hw/pci/pci.c:262: pci_bus_change_irq_level: Assertion `irq_num >= 0' failed.
Thus we should allocate an IRQ line for the device in slot 0, too.
To avoid changes to the outside of ppc4xx_pci.c, we map it to
the internal IRQ number 4 which will then happily be ignored since
ppc440_bamboo.c does not wire it up.
With these changes it is now possible again to use recent Linux
kernels for the bamboo board.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20211019091817.469003-1-thuth@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This only helps Linux guests as only that seems to use it.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <1c1e030f2bbc86e950b3310fb5922facdc21ef86.1634241019.git.balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Define a constant for PCI config addresses to make it clearer what
these numbers are.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <9bd8e84d02d91693b71082a1fadeb86e6bce3025.1634241019.git.balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Instead of relying on the mapped address of the MV64361 registers
access them via their memory region. This is not a problem at reset
time when these registers are mapped at the default address but the
guest could change this later and then the RTAS calls accessing PCI
config registers could fail. None of the guests actually do this so
this only avoids a theoretical problem not seen in practice.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <b6f768023603dc2c4d130720bcecdbea459b7668.1634241019.git.balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is needed for Linux to access RTC time.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <6233eb07c680d6c74427e11b9641958f98d53378.1634241019.git.balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Issue a warning when using VOF (which is the default) but no -kernel
option given to let users know that it will likely fail as the guest
has nothing to run. It is not a hard error because it may still be
useful to start the machine without further options for testing or
inspecting it from monitor without actually booting it.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <a4ec9a900df772b91e9f69ca7a0799d8ae293e5a.1634241019.git.balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The CHRP spec this board confirms to only allows 2 GiB of system
memory below 4 GiB as the high 2 GiB is allocated to IO and system
resources. To avoid problems with memory overlapping these areas
restrict RAM to 2 GiB similar to mac_newworld.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <54f58229a69c9c1cca21bcecad700b3d7052edd5.1634241019.git.balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When using u-boot as firmware with the taihu board, QEMU aborts with
this assertion:
ERROR:../accel/tcg/tcg-accel-ops.c:79:tcg_handle_interrupt: assertion failed:
(qemu_mutex_iothread_locked())
Running QEMU with "-d in_asm" shows that the crash happens when writing
to SPR 0x3f2, so we are missing to lock the iothread in the code path
here.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20211006071140.565952-1-thuth@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Commit 962104f044 ("hw/ppc: moved hcalls that depend on softmmu")
introduced a lot of unnecessary #include directives. Remove them.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20211006170801.178023-1-philmd@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Commit 4d9b8ef9b5 ("target/ppc: Fix 64-bit decrementer") introduced
new int64t variables and broke the test triggering the decrementer
exception. Revert partially the change to evaluate both clause of the
if statement.
Reported-by: Coverity CID 1464061
Fixes: 4d9b8ef9b5 ("target/ppc: Fix 64-bit decrementer")
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211005053324.441132-1-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
DeviceState.id is a pointer to a string that is stored in the QemuOpts
object DeviceState.opts and freed together with it. We want to create
devices without going through QemuOpts in the future, so make this a
separately allocated string.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20211008133442.141332-9-kwolf@redhat.com>
Reviewed-by: Damien Hedde <damien.hedde@greensocs.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Peter Krempa <pkrempa@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Now we have a common structure SMPCompatProps used to store information
about SMP compatibility stuff, so we can also move smp_prefer_sockets
there for cleaner code.
No functional change intended.
Signed-off-by: Yanan Wang <wangyanan55@huawei.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20210929025816.21076-15-wangyanan55@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In the real SMP hardware topology world, it's much more likely that
we have high cores-per-socket counts and few sockets totally. While
the current preference of sockets over cores in smp parsing results
in a virtual cpu topology with low cores-per-sockets counts and a
large number of sockets, which is just contrary to the real world.
Given that it is better to make the virtual cpu topology be more
reflective of the real world and also for the sake of compatibility,
we start to prefer cores over sockets over threads in smp parsing
since machine type 6.2 for different arches.
In this patch, a boolean "smp_prefer_sockets" is added, and we only
enable the old preference on older machines and enable the new one
since type 6.2 for all arches by using the machine compat mechanism.
Suggested-by: Daniel P. Berrange <berrange@redhat.com>
Signed-off-by: Yanan Wang <wangyanan55@huawei.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Pankaj Gupta <pankaj.gupta@ionos.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20210929025816.21076-10-wangyanan55@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Rename the "allocate and return" qbus creation function to
qbus_new(), to bring it into line with our _init vs _new convention.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Message-id: 20210923121153.23754-6-peter.maydell@linaro.org
This patch has a handful of modifications for the recent added
FORM2 support:
- to not allocate more than the necessary size in 'distance_table'.
At this moment the array is oversized due to allocating uint32_t for
all elements, when most of them fits in an uint8_t. Fix it by
changing the array to uint8_t and allocating the exact size;
- use stl_be_p() to store the uint32_t at the start of 'distance_table';
- use sizeof(uint32_t) to skip the uint32_t length when populating the
distances;
- use the NUMA_DISTANCE_MIN macro from sysemu/numa.h to avoid hardcoding
the local distance value.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210922122852.130054-2-danielhb413@gmail.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The current way the mask is built can overflow with a 64-bit decrementer.
Use sextract64() to extract the signed values and remove the logic to
handle negative values which has become useless.
Cc: Luis Fernando Fujita Pires <luis.pires@eldorado.org.br>
Fixes: a8dafa5251 ("target/ppc: Implement large decrementer support for TCG")
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210920061203.989563-5-clg@kaod.org>
Reviewed-by: Luis Pires <luis.pires@eldorado.org.br>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
numa_complete_configuration() in hw/core/numa.c always adds a NUMA node
for the pSeries machine if none was specified, but without node distance
information for the single node created.
NUMA FORM1 affinity code didn't rely on numa_state information to do its
job, but FORM2 does. As is now, this is the result of a pSeries guest
with NUMA FORM2 affinity when no NUMA nodes is specified:
$ numactl -H
available: 1 nodes (0)
node 0 cpus: 0
node 0 size: 16222 MB
node 0 free: 15681 MB
No distance information available.
This can be amended in spapr_numa_FORM2_write_rtas_tables(). We're
enforcing that the local distance (the distance to the node to itself) is
always 10. This allows for the proper creation of the NUMA distance tables,
fixing the output of 'numactl -H' in the guest:
$ numactl -H
available: 1 nodes (0)
node 0 cpus: 0
node 0 size: 16222 MB
node 0 free: 15685 MB
node distances:
node 0
0: 10
CC: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210920174947.556324-8-danielhb413@gmail.com>
Acked-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The main feature of FORM2 affinity support is the separation of NUMA
distances from ibm,associativity information. This allows for a more
flexible and straightforward NUMA distance assignment without relying on
complex associations between several levels of NUMA via
ibm,associativity matches. Another feature is its extensibility. This base
support contains the facilities for NUMA distance assignment, but in the
future more facilities will be added for latency, performance, bandwidth
and so on.
This patch implements the base FORM2 affinity support as follows:
- the use of FORM2 associativity is indicated by using bit 2 of byte 5
of ibm,architecture-vec-5. A FORM2 aware guest can choose to use FORM1
or FORM2 affinity. Setting both forms will default to FORM2. We're not
advertising FORM2 for pseries-6.1 and older machine versions to prevent
guest visible changes in those;
- ibm,associativity-reference-points has a new semantic. Instead of
being used to calculate distances via NUMA levels, it's now used to
indicate the primary domain index in the ibm,associativity domain of
each resource. In our case it's set to {0x4}, matching the position
where we already place logical_domain_id;
- two new RTAS DT artifacts are introduced: ibm,numa-lookup-index-table
and ibm,numa-distance-table. The index table is used to list all the
NUMA logical domains of the platform, in ascending order, and allows for
spartial NUMA configurations (although QEMU ATM doesn't support that).
ibm,numa-distance-table is an array that contains all the distances from
the first NUMA node to all other nodes, then the second NUMA node
distances to all other nodes and so on;
- get_max_dist_ref_points(), get_numa_assoc_size() and get_associativity()
now checks for OV5_FORM2_AFFINITY and returns FORM2 values if the guest
selected FORM2 affinity during CAS.
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210920174947.556324-7-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
FORM2 NUMA affinity is prepared to deal with empty (memory/cpu less)
NUMA nodes. This is used by the DAX KMEM driver to locate a PAPR SCM
device that has a different latency than the original NUMA node from the
regular memory. FORM2 is also able to deal with asymmetric NUMA
distances gracefully, something that our FORM1 implementation doesn't
do.
Move these FORM1 verifications to a new function and wait until after
CAS, when we're sure that we're sticking with FORM1, to enforce them.
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210920174947.556324-6-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Introducing a new NUMA affinity, FORM2, requires a new mechanism to
switch between affinity modes after CAS. Also, we want FORM2 data
structures and functions to be completely separated from the existing
FORM1 code, allowing us to avoid adding new code that inherits the
existing complexity of FORM1.
The idea of switching values used by the write_dt() functions in
spapr_numa.c was already introduced in the previous patch, and
the same approach will be used when dealing with the FORM1 and FORM2
arrays.
We can accomplish that by that by renaming the existing numa_assoc_array
to FORM1_assoc_array, which now is used exclusively to handle FORM1 affinity
data. A new helper get_associativity() is then introduced to be used by the
write_dt() functions to retrieve the current ibm,associativity array of
a given node, after considering affinity selection that might have been
done during CAS. All code that was using numa_assoc_array now needs to
retrieve the array by calling this function.
This will allow for an easier plug of FORM2 data later on.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210920174947.556324-5-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The next preliminary step to introduce NUMA FORM2 affinity is to make
the existing code independent of FORM1 macros and values, i.e.
MAX_DISTANCE_REF_POINTS, NUMA_ASSOC_SIZE and VCPU_ASSOC_SIZE. This patch
accomplishes that by doing the following:
- move the NUMA related macros from spapr.h to spapr_numa.c where they
are used. spapr.h gets instead a 'NUMA_NODES_MAX_NUM' macro that is used
to refer to the maximum number of NUMA nodes, including GPU nodes, that
the machine can support;
- MAX_DISTANCE_REF_POINTS and NUMA_ASSOC_SIZE are renamed to
FORM1_DIST_REF_POINTS and FORM1_NUMA_ASSOC_SIZE. These FORM1 specific
macros are used in FORM1 init functions;
- code that uses MAX_DISTANCE_REF_POINTS now retrieves the
max_dist_ref_points value using get_max_dist_ref_points().
NUMA_ASSOC_SIZE is replaced by get_numa_assoc_size() and VCPU_ASSOC_SIZE
is replaced by get_vcpu_assoc_size(). These functions are used by the
generic device tree functions and h_home_node_associativity() and will
allow them to switch between FORM1 and FORM2 without changing their core
logic.
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210920174947.556324-4-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When first introduced, 'legacy_numa' was a way to refer to guests that
either wouldn't be affected by associativity domain calculations, namely
the ones with only 1 NUMA node, and pre 5.2 guests that shouldn't be
affected by it because it would be an userspace change. Calling these
cases 'legacy_numa' was a convenient way to label these cases.
We're about to introduce a new NUMA affinity, FORM2, and this concept
of 'legacy_numa' is now a bit misleading because, although it is called
'legacy' it is in fact a FORM1 exclusive contraint.
This patch removes spapr_machine_using_legacy_numa() and open code the
conditions in each caller. While we're at it, move the chunk inside
spapr_numa_FORM1_affinity_init() that sets all numa_assoc_array domains
with 'node_id' to spapr_numa_define_FORM1_domains(). This chunk was
being executed if !pre_5_2_numa_associativity and num_nodes => 1, the
same conditions in which spapr_numa_define_FORM1_domains() is called
shortly after.
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210920174947.556324-3-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The upcoming FORM2 NUMA affinity will support asymmetric NUMA topologies
and doesn't need be concerned with all the legacy support for older
pseries FORM1 guests.
We're also not going to calculate associativity domains based on numa
distance (via spapr_numa_define_associativity_domains) since the
distances will be written directly into new DT properties.
Let's split FORM1 code into its own functions to allow for easier
insertion of FORM2 logic later on.
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210920174947.556324-2-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
If an unknown pin of the IRQ controller is raised, something is very
wrong in the QEMU model. It is better to abort.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210920061203.989563-3-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Linux Kernel 5.12 is now unisolating CPU DRCs in the device_removal
error path, signalling that the hotunplug process wasn't successful.
This allow us to send a DEVICE_UNPLUG_GUEST_ERROR in drc_unisolate_logical()
to signal this error to the management layer.
We also have another error path in spapr_memory_unplug_rollback() for
configured LMB DRCs. Kernels older than 5.13 will not unisolate the LMBs
in the hotunplug error path, but it will reconfigure them. Let's send
the DEVICE_UNPLUG_GUEST_ERROR event in that code path as well to cover the
case of older kernels.
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210907004755.424931-7-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The error_report() call in drc_unisolate_logical() is not considering
that drc->dev->id can be NULL, and the underlying functions error_report()
calls to do its job (vprintf(), g_strdup_printf() ...) has undefined
behavior when trying to handle "%s" with NULL arguments.
Besides, there is no utility into reporting that an unknown device was
rejected by the guest.
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210907004755.424931-4-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
As done in hw/acpi/memory_hotplug.c, pass an empty string if dev->id
is NULL to qapi_event_send_mem_unplug_error() to avoid relying on
a behavior that can be changed in the future.
Suggested-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210907004755.424931-3-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210902130928.528803-3-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This to avoid possible conflicts with the "id" property of QOM objects.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210901094153.227671-9-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
On P10, the chip id is calculated from the "Primary topology table
index". See skiboot commits for more information [1].
This information is extracted from the hdata on real systems which
QEMU needs to emulate. Add this property for all machines even if it
is only used on POWER10.
[1] https://github.com/open-power/skiboot/commit/2ce3f083f399https://github.com/open-power/skiboot/commit/a2d4d7f9e14a
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210901094153.227671-4-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210901094153.227671-3-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Add 6.2 machine types for arm/i440fx/q35/s390x/spapr.
Signed-off-by: Yanan Wang <wangyanan55@huawei.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Pankaj Gupta <pankaj.gupta@ionos.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
First ppc pull request for qemu-6.2. As usual, there's a fair bit
here, since it's been queued during the 6.1 freeze. Highlights are:
* Some fixes for 128 bit arithmetic and some vector opcodes that use
them
* Significant improvements to the powernv to support POWER10 cpus
(more to come though)
* Several cleanups to the ppc softmmu code
* A few other assorted fixes
-----BEGIN PGP SIGNATURE-----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=C5XY
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dg-gitlab/tags/ppc-for-6.2-20210827' into staging
ppc patch queue 2021-08-27
First ppc pull request for qemu-6.2. As usual, there's a fair bit
here, since it's been queued during the 6.1 freeze. Highlights are:
* Some fixes for 128 bit arithmetic and some vector opcodes that use
them
* Significant improvements to the powernv to support POWER10 cpus
(more to come though)
* Several cleanups to the ppc softmmu code
* A few other assorted fixes
# gpg: Signature made Fri 27 Aug 2021 08:09:12 BST
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dg-gitlab/tags/ppc-for-6.2-20210827:
target/ppc: fix vector registers access in gdbstub for little-endian
include/qemu/int128.h: introduce bswap128s
target/ppc: fix vextu[bhw][lr]x helpers
include/qemu/int128.h: define struct Int128 according to the host endianness
ppc/xive: Export xive_presenter_notify()
ppc/xive: Export PQ get/set routines
ppc/pnv: add a chip topology index for POWER10
ppc/pnv: Distribute RAM among the chips
ppc/pnv: Use a simple incrementing index for the chip-id
ppc/pnv: powerpc_excp: Do not discard HDECR exception when entering power-saving mode
ppc/pnv: Change the POWER10 machine to support DD2 only
ppc: Add a POWER10 DD2 CPU
ppc/pnv: update skiboot to commit 820d43c0a775.
target/ppc: moved store_40x_sler to helper_regs.c
target/ppc: moved ppc_store_sdr1 to mmu_common.c
target/ppc: divided mmu_helper.c in 2 files
spapr_pci: Fix leak in spapr_phb_vfio_get_loc_code() with g_autofree
xive: Remove extra '0x' prefix in trace events
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
But always give the first 1GB to chip 0 as skiboot requires it.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210809134547.689560-6-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When the QEMU PowerNV machine was introduced, multi chip support
modeled a two socket system with dual chip modules as found on some P8
Tuleta systems (8286-42A). But this is hardly used and not relevant
for QEMU. Use a simple index instead.
With this change, we can now increase the max socket number to 16 as
found on high end systems.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210809134547.689560-5-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
There is no need to keep the DD1 chip model as it will never be
publicly available.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210809134547.689560-3-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This uses g_autofree to simplify logic in spapr_phb_vfio_get_loc_code(),
in the process fixing a leak in one of the paths. I'm told this fixes
Coverity error CID 1460454
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Fixes: 16b0ea1d85 ("spapr_pci: populate ibm,loc-code")
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
arch_init.h only defines the QEMU_ARCH_* enumeration and the
arch_type global. Don't include it in files that don't use those.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210730105947.28215-8-peter.maydell@linaro.org
spapr_mce_req_event() makes an effort to prevent migration from
degrading the reporting of FWNMIs. It adds a migration blocker when
it receives one, and deletes it when it's done handling it. This is a
best effort.
Commit 2500fb423a "migration: Include migration support for machine
check handling" tried to explain this in a comment. Rewrite the
comment for clarity, and reposition it to make it clear it applies to
all failure modes, not just "migration already in progress".
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: Aravinda Prasad <arawinda.p@gmail.com>
Cc: Ganesh Goudar <ganeshgr@linux.ibm.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20210720125408.387910-4-armbru@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Coverity reported issues which are caused by mixing of signed return codes
from DTC and unsigned return codes of the client interface.
This introduces PROM_ERROR and makes distinction between the error types.
This fixes NEGATIVE_RETURNS, OVERRUN issues reported by Coverity.
This adds a comment about the return parameters number in the VOF hcall.
The reason for such counting is to keep the numbers look the same in
vof_client_handle() and the Linux (an OF client).
vmc->client_architecture_support() returns target_ulong and we want to
propagate this to the client (for example H_MULTI_THREADS_ACTIVE).
The VOF path to do_client_architecture_support() needs chopping off
the top 32bit but SLOF's H_CAS does not; and either way the return values
are either 0 or 32bit negative error code. For now this chops
the top 32bits.
This makes "claim" fail if the allocated address is above 4GB as
the client interface is 32bit. This still allows claiming memory above
4GB as potentially initrd can be put there and the client can read
the address from the FDT's "available" property.
Fixes: CID 1458139, 1458138, 1458137, 1458133, 1458132
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Message-Id: <20210720050726.2737405-1-aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The -append option is currently not compatible with -bios (as we don't
yet emulate nvram so we can only put it in the environment with VOF).
Therefore a warning is printed if -append is used with -bios but
because the default value of kernel_cmdline seems to be an empty
string instead of NULL this warning was printed even without -append
when -bios is used. Only print warning if -append is given.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <483ac599a1407b766179aaea2794aed60cc09f53.1626367844.git.balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
From clang-13:
hw/ppc/spapr_events.c:937:14: error: variable 'xinfo' set but not used \
[-Werror,-Wunused-but-set-variable]
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The ATI VGA device isn't a requisite for the Pegasos2 machine
because Linux only uses the serial console; see commit ba7e5ac18e
("hw/ppc: Add emulation of Genesi/bPlan Pegasos II") for rationale.
Using the default devices we don't have any problem:
$ qemu-system-ppc -M pegasos2
qemu-system-ppc: standard VGA not available
But when trying to explicitly use the ATI device we get an error:
$ qemu-system-ppc -M pegasos2 -vga none -bios pegasos2.rom -device ati-vga,romfile=
qemu-system-ppc: -device ati-vga,romfile=: 'ati-vga' is not a valid device model name
Add it as an implicit Kconfig dependency.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210515173716.358295-13-philmd@redhat.com>
Acked-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Peter Xu
Thomas Huth
BALATON Zoltan
Philippe Mathieu-Daudé
Cédric Le Goater
Kevin Wolf
Yanan Wang
Peter Maydell
Daniel Henrique Barboza
David Gibson
Markus Armbruster
Alexey Kardashevskiy
Richard Henderson
Philippe Mathieu-Daudé