Add Kconfig dependencies for the Exynos-related boards (nuri and
smdkc210).
This patch is slightly based on earlier work by Ákos Kovács (i.e.
his "hw/arm/Kconfig: Add ARM Kconfig" patch).
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Header guard symbols should match their file name to make guard
collisions less likely.
Cleaned up with scripts/clean-header-guards.pl, followed by some
renaming of new guard symbols picked by the script to better ones.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190315145123.28030-6-armbru@redhat.com>
[Rebase to master: update include/hw/net/ne2000-isa.h]
We currently use Qemu's default of 128MB. As we know how much ram each
machine ships with, make it easier on users by setting a default.
It can still be overridden with -m on the command line.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190503022958.1394-1-joel@jms.id.au
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Raspberry Pi boards have a physical memory map which does
not allow for more than 1GB of RAM. Currently if the user tries
to ask for more then we fail in a confusing way:
$ qemu-system-aarch64 --machine raspi3 -m 8G
Unexpected error in visit_type_uintN() at qapi/qapi-visit-core.c:164:
qemu-system-aarch64: Parameter 'vcram-base' expects uint32_t
Aborted (core dumped)
Catch this earlier and diagnose it with a more friendly message:
$ qemu-system-aarch64 --machine raspi3 -m 8G
qemu-system-aarch64: Requested ram size is too large for this machine: maximum is 1GB
Fixes: https://bugs.launchpad.net/qemu/+bug/1794187
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
The ARM virt machines put firmware in flash memory. To configure it,
you use -drive if=pflash,unit=0,... and optionally -drive
if=pflash,unit=1,...
Why two -drive? This permits setting up one part of the flash memory
read-only, and the other part read/write. It also makes upgrading
firmware on the host easier. Below the hood, we get two separate
flash devices, because we were too lazy to improve our flash device
models to support sector protection.
The problem at hand is to do the same with -blockdev somehow, as one
more step towards deprecating -drive.
We recently solved this problem for x86 PC machines, in commit
ebc29e1bea. See the commit message for design rationale.
This commit solves it for ARM virt basically the same way: new machine
properties pflash0, pflash1 forward to the onboard flash devices'
properties. Requires creating the onboard devices in the
.instance_init() method virt_instance_init(). The existing code to
pick up drives defined with -drive if=pflash is replaced by code to
desugar into the machine properties.
There are a few behavioral differences, though:
* The flash devices are always present (x86: only present if
configured)
* Flash base addresses and sizes are fixed (x86: sizes depend on
images, mapped back to back below a fixed address)
* -bios configures contents of first pflash (x86: -bios configures ROM
contents)
* -bios is rejected when first pflash is also configured with -machine
pflash0=... (x86: bios is silently ignored then)
* -machine pflash1=... does not require -machine pflash0=... (x86: it
does).
The actual code is a bit simpler than for x86 mostly due to the first
two differences.
Before the patch, all the action is in create_flash(), called from the
machine's .init() method machvirt_init():
main()
machine_run_board_init()
machvirt_init()
create_flash()
create_one_flash() for flash[0]
create
configure
includes obeying -drive if=pflash,unit=0
realize
map
fall back to -bios
create_one_flash() for flash[1]
create
configure
includes obeying -drive if=pflash,unit=1
realize
map
update FDT
To make the machine properties work, we need to move device creation
to its .instance_init() method virt_instance_init().
Another complication is machvirt_init()'s computation of
@firmware_loaded: it predicts what create_flash() will do. Instead of
predicting what create_flash()'s replacement virt_firmware_init() will
do, I decided to have virt_firmware_init() return what it did.
Requires calling it a bit earlier.
Resulting call tree:
main()
current_machine = object_new()
...
virt_instance_init()
virt_flash_create()
virt_flash_create1() for flash[0]
create
configure: set defaults
become child of machine [NEW]
add machine prop pflash0 as alias for drive [NEW]
virt_flash_create1() for flash[1]
create
configure: set defaults
become child of machine [NEW]
add machine prop pflash1 as alias for drive [NEW]
for all machine props from the command line: machine_set_property()
...
property_set_alias() for machine props pflash0, pflash1
...
set_drive() for cfi.pflash01 prop drive
this is how -machine pflash0=... etc set
machine_run_board_init(current_machine);
virt_firmware_init()
pflash_cfi01_legacy_drive()
legacy -drive if=pflash,unit=0 and =1 [NEW]
virt_flash_map()
virt_flash_map1() for flash[0]
configure: num-blocks
realize
map
virt_flash_map1() for flash[1]
configure: num-blocks
realize
map
fall back to -bios
virt_flash_fdt()
update FDT
You have László to thank for making me explain this in detail.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Message-id: 20190416091348.26075-4-armbru@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This commit finally deletes "hw/devices.h".
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190412165416.7977-13-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190412165416.7977-12-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190412165416.7977-10-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Since uWireSlave is only used in this new header, there is no
need to expose it via "qemu/typedefs.h".
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190412165416.7977-9-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190412165416.7977-8-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190412165416.7977-7-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add an entries the Blizzard device in MAINTAINERS.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190412165416.7977-6-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190412165416.7977-5-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Suggested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190412165416.7977-3-philmd@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190412165416.7977-2-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SMMUNotifierNode struct is not necessary and brings extra
complexity so let's remove it. We now directly track the SMMUDevices
which have registered IOMMU MR notifiers.
This is inspired from the same transformation on intel-iommu
done in commit b4a4ba0d68
("intel-iommu: remove IntelIOMMUNotifierNode")
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Message-id: 20190409160219.19026-1-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some trace points are attributed to the wrong source file. Happens
when we neglect to update trace-events for code motion, or add events
in the wrong place, or misspell the file name.
Clean up with help of cleanup-trace-events.pl. Same funnies as in the
previous commit, of course. Manually shorten its change to
linux-user/trace-events to */signal.c.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-id: 20190314180929.27722-6-armbru@redhat.com
Message-Id: <20190314180929.27722-6-armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Tracked down with cleanup-trace-events.pl. Funnies requiring manual
post-processing:
* block.c and blockdev.c trace points are in block/trace-events.
* hw/block/nvme.c uses the preprocessor to hide its trace point use
from cleanup-trace-events.pl.
* include/hw/xen/xen_common.h trace points are in hw/xen/trace-events.
* net/colo-compare and net/filter-rewriter.c use pseudo trace points
colo_compare_udp_miscompare and colo_filter_rewriter_debug to guard
debug code.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-id: 20190314180929.27722-5-armbru@redhat.com
Message-Id: <20190314180929.27722-5-armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
We spell out sub/dir/ in sub/dir/trace-events' comments pointing to
source files. That's because when trace-events got split up, the
comments were moved verbatim.
Delete the sub/dir/ part from these comments. Gets rid of several
misspellings.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190314180929.27722-3-armbru@redhat.com
Message-Id: <20190314180929.27722-3-armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This is more proper to use PCIE_MMCFG_BUS to retrieve end_bus_number.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20190312074953.16671-1-richardw.yang@linux.intel.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The GSIV numbers of the SPI based interrupts is not correct as
ARM_SPI_BASE was not added to the irqmap[VIRT_SMMU] value. So
this may collide with VIRTIO_MMIO irq window.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20190312091031.5185-1-eric.auger@redhat.com
Reviewed-by: Shannon Zhao <shannon.zhaosl@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Our pflash devices are simplistically modelled has having
"num-blocks" sectors of equal size "sector-length". Real hardware
commonly has sectors of different sizes. How our "sector-length"
property is related to the physical device's multiple sector sizes
is unclear.
Helper functions pflash_cfi01_register() and pflash_cfi02_register()
create a pflash device, set properties including "sector-length" and
"num-blocks", and realize. They take parameters @size, @sector_len
and @nb_blocs.
QOMification left parameter @size unused. Obviously, @size should
match @sector_len and @nb_blocs, i.e. size == sector_len * nb_blocs.
All callers satisfy this.
Remove @nb_blocs and compute it from @size and @sector_len.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20190308094610.21210-16-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
QOMification left parameter @qdev unused in pflash_cfi01_register()
and pflash_cfi02_register(). All callers pass NULL. Remove.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190308094610.21210-15-armbru@redhat.com>
We have two open-coded copies of macro PFLASH_CFI01(). Move the macro
to the header, so we can ditch the copies. Move PFLASH_CFI02() to the
header for symmetry.
We define macros TYPE_PFLASH_CFI01 and TYPE_PFLASH_CFI02 for type name
strings, then mostly use the strings. If the macros are worth
defining, they are worth using. Replace the strings by the macros.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20190308094610.21210-6-armbru@redhat.com>
flash.h's incomplete struct pflash_t is completed both in
pflash_cfi01.c and in pflash_cfi02.c. The complete types are
incompatible. This can hide type errors, such as passing a pflash_t
created with pflash_cfi02_register() to pflash_cfi01_get_memory().
Furthermore, POSIX reserves typedef names ending with _t.
Rename the two structs to PFlashCFI01 and PFlashCFI02.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190308094610.21210-2-armbru@redhat.com>
Since commit 578f3c7b08 ("arm: add fw_cfg to "virt" board",
2014-12-22), the machvirt_init() unconditionally creates the
fw_cfg object. Later, commit c30e15658b ("smbios: implement
smbios support for mach-virt", 2015-09-07) added a superfluous
null-check on it.
Remove this superfluous check.
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190309181920.30553-2-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
I had to include an enum for audio sampling formats into qapi, but that
meant duplicating the audfmt_e enum. This patch replaces audfmt_e and
associated values with the qapi generated AudioFormat enum.
This patch is mostly a search-and-replace, except for switches where the
qapi generated AUDIO_FORMAT_MAX caused problems.
Signed-off-by: Kővágó, Zoltán <DirtY.iCE.hu@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 01251b2758a1679c66842120b77c0fb46d7d0eaf.1552083282.git.DirtY.iCE.hu@gmail.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-39-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The make_device_config.sh script is replaced by minikconf, which
is modified to support the same command line as its predecessor.
The roots of the parsing are default-configs/*.mak, Kconfig.host and
hw/Kconfig. One difference with make_device_config.sh is that all symbols
have to be defined in a Kconfig file, including those coming from the
configure script. This is the reason for the Kconfig.host file introduced
in the previous patch. Whenever a file in default-configs/*.mak used
$(...) to refer to a config-host.mak symbol, this is replaced by a
Kconfig dependency; this part must be done already in this patch
for bisectability.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-28-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The Kconfig files were generated mostly with this script:
for i in `grep -ho CONFIG_[A-Z0-9_]* default-configs/* | sort -u`; do
set fnord `git grep -lw $i -- 'hw/*/Makefile.objs' `
shift
if test $# = 1; then
cat >> $(dirname $1)/Kconfig << EOF
config ${i#CONFIG_}
bool
EOF
git add $(dirname $1)/Kconfig
else
echo $i $*
fi
done
sed -i '$d' hw/*/Kconfig
for i in hw/*; do
if test -d $i && ! test -f $i/Kconfig; then
touch $i/Kconfig
git add $i/Kconfig
fi
done
Whenever a symbol is referenced from multiple subdirectories, the
script prints the list of directories that reference the symbol.
These symbols have to be added manually to the Kconfig files.
Kconfig.host and hw/Kconfig were created manually.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-27-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Implement the watchdog timer for the stellaris boards.
This device is a close variant of the CMSDK APB watchdog
device, so we can model it by subclassing that device and
tweaking the behaviour of some of its registers.
Signed-off-by: Michel Heily <michelheily@gmail.com>
Reviewed-by: Peter Maydell <petser.maydell@linaro.org>
[PMM: rewrote commit message, fixed a few checkpatch nits,
added comment giving the URL of the spec for the Stellaris
variant of the watchdog device]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Now we have the extended memory map (high IO regions beyond the
scalable RAM) and dynamic IPA range support at KVM/ARM level
we can bump the legacy 255GB initial RAM limit. The actual maximum
RAM size now depends on the physical CPU and host kernel, in
accelerated mode. In TCG mode, it depends on the VCPU
AA64MMFR0.PARANGE.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20190304101339.25970-11-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We are about to allow the memory map to grow beyond 1TB and
potentially overshoot the VCPU AA64MMFR0.PARANGE.
In aarch64 mode and when highmem is set, let's check the VCPU
PA range is sufficient to address the highest GPA of the memory
map.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20190304101339.25970-10-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch implements the machine class kvm_type() callback.
It returns the number of bits requested to implement the whole GPA
range including the RAM and IO regions located beyond.
The returned value is passed though the KVM_CREATE_VM ioctl and
this allows KVM to set the stage2 tables dynamically.
To compute the highest GPA used in the memory map, kvm_type()
must freeze the memory map by calling virt_set_memmap().
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20190304101339.25970-9-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Up to now the memory map has been static and the high IO region
base has always been 256GiB.
This patch modifies the virt_set_memmap() function, which freezes
the memory map, so that the high IO range base becomes floating,
located after the initial RAM and the device memory.
The function computes
- the base of the device memory,
- the size of the device memory,
- the high IO region base
- the highest GPA used in the memory map.
Entries of the high IO region are assigned a base address. The
device memory is initialized.
The highest GPA used in the memory map will be used at VM creation
to choose the requested IPA size.
Setting all the existing highmem IO regions beyond the RAM
allows to have a single contiguous RAM region (initial RAM and
possible hotpluggable device memory). That way we do not need
to do invasive changes in the EDK2 FW to support a dynamic
RAM base.
Still the user cannot request an initial RAM size greater than 255GB.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20190304101339.25970-8-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In the prospect to introduce an extended memory map supporting more
RAM, let's split the memory map array into two parts:
- the former a15memmap, renamed base_memmap, contains regions below
and including the RAM. MemMapEntries initialized in this array
have a static size and base address.
- extended_memmap, only initialized with entries located after the
RAM. MemMapEntries initialized in this array only get their size
initialized. Their base address is dynamically computed depending
on the the top of the RAM, with same alignment as their size.
Eventually base_memmap entries are copied into the extended_memmap
array. Using two separate arrays however clarifies which entries
are statically allocated and those which are dynamically allocated.
This new split will allow to grow the RAM size without changing the
description of the high IO entries.
We introduce a new virt_set_memmap() helper function which
"freezes" the memory map. We call it in machvirt_init as
memory attributes of the machine are not yet set when
virt_instance_init() gets called.
The memory map is unchanged (the top of the initial RAM still is
256GiB). Then come the high IO regions with same layout as before.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20190304101339.25970-4-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In preparation for a split of the memory map into a static
part and a dynamic part floating after the RAM, let's rename the
regions located after the RAM
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20190304101339.25970-3-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We introduce an helper to create a memory node.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190304101339.25970-2-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This was changed a little bit since my post on Feb 20 (to which
there were no comments) due to changes I had to work around:
Change b296b664ab "smbus: Add a helper to generate SPD EEPROM
data" added a function to include/hw/i2c/smbus.h, which I had to move to
include/hw/smbus_eeprom.h.
There were some changes to hw/i2c/Makefile.objs that I had to fix up.
Beyond that, no changes.
Thanks,
-corey
-----BEGIN PGP SIGNATURE-----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=XTkI
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/cminyard/tags/i2c-for-release-20190228' into staging
This has been out there long enough, I need to get this in.
This was changed a little bit since my post on Feb 20 (to which
there were no comments) due to changes I had to work around:
Change b296b664ab "smbus: Add a helper to generate SPD EEPROM
data" added a function to include/hw/i2c/smbus.h, which I had to move to
include/hw/smbus_eeprom.h.
There were some changes to hw/i2c/Makefile.objs that I had to fix up.
Beyond that, no changes.
Thanks,
-corey
# gpg: Signature made Thu 28 Feb 2019 18:05:49 GMT
# gpg: using RSA key FD0D5CE67CE0F59A6688268661F38C90919BFF81
# gpg: Good signature from "Corey Minyard <cminyard@mvista.com>" [unknown]
# gpg: aka "Corey Minyard <minyard@acm.org>" [unknown]
# gpg: aka "Corey Minyard <corey@minyard.net>" [unknown]
# gpg: aka "Corey Minyard <minyard@mvista.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: FD0D 5CE6 7CE0 F59A 6688 2686 61F3 8C90 919B FF81
* remotes/cminyard/tags/i2c-for-release-20190228:
i2c: Verify that the count passed in to smbus_eeprom_init() is valid
i2c:smbus_eeprom: Add a reset function to smbus_eeprom
i2c:smbus_eeprom: Add vmstate handling to the smbus eeprom
i2c:smbus_eeprom: Add a size constant for the smbus_eeprom size
i2c:smbus_eeprom: Add normal type name and cast to smbus_eeprom.c
i2c:smbus_slave: Add an SMBus vmstate structure
i2c:pm_smbus: Fix state transfer
migration: Add a VMSTATE_BOOL_TEST() macro
i2c:pm_smbus: Fix pm_smbus handling of I2C block read
boards.h: Ignore migration for SMBus devices on older machines
i2c:smbus: Make white space in switch statements consistent
i2c:smbus_eeprom: Get rid of the quick command
i2c:smbus: Simplify read handling
i2c:smbus: Simplify write operation
i2c:smbus: Correct the working of quick commands
i2c: Don't check return value from i2c_recv()
arm:i2c: Don't mask return from i2c_recv()
i2c: have I2C receive operation return uint8_t
i2c: Split smbus into parts
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
At the moment the handling of init-svtor and cpuwait initial
values is split between armsse.c and iotkit-sysctl.c:
the code in armsse.c sets the initial state of the CPU
object by setting the init-svtor and start-powered-off
properties, but the iotkit-sysctl.c code has its own
code setting the reset values of its registers (which are
then used when updating the CPU when the guest makes
runtime changes).
Clean this up by making the armsse.c code set properties on the
iotkit-sysctl object to define the initial values of the
registers, so they always match the initial CPU state,
and update the comments in armsse.c accordingly.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190219125808.25174-9-peter.maydell@linaro.org
The SYSCTL block in the SSE-200 has some extra registers that
are not present in the IoTKit version. Add these registers
(as reads-as-written stubs), enabled by a new QOM property.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190219125808.25174-7-peter.maydell@linaro.org
Create and connect the MHUs in the SSE-200.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190219125808.25174-3-peter.maydell@linaro.org
It can't fail, and now that it returns a uint8_t a 0xff mask
is unnecessary.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
It is never supposed to fail and cannot return an error, so just
have it return the proper type. Have it return 0xff on nothing
available, since that's what would happen on a real bus.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
smbus.c and smbus.h had device side code, master side code, and
smbus.h has some smbus_eeprom.c definitions. Split them into
separate files.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The region 0x40010000 .. 0x4001ffff and its secure-only alias
at 0x50010000... are for per-CPU devices. We implement this by
giving each CPU its own container memory region, where the
per-CPU devices live. Unfortunately, the alias region which
makes devices mapped at 0x4... addresses also appear at 0x5...
is only implemented in the overall "all CPUs" container. The
effect of this bug is that the CPU_IDENTITY register block appears
only at 0x4001f000, but not at the 0x5001f000 alias where it should
also appear. Guests (like very recent Arm Trusted Firmware-M)
which try to access it at 0x5001f000 will crash.
Fix this by moving the handling for this alias from the "all CPUs"
container to the per-CPU container. (We leave the aliases for
0x1... and 0x3... in the overall container, because there are
no per-CPU devices there.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20190215180500.6906-1-peter.maydell@linaro.org
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Wire up the two PL011 UARTs in the Musca board.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Wire up the PL031 RTC for the Musca board.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The Musca board puts its SRAM and flash behind TrustZone
Memory Protection Controllers (MPCs). Each MPC sits between
the CPU and the RAM/flash, and also has a set of memory mapped
control registers. Wire up the MPCs, and the memory behind them.
For the moment we implement the flash as simple ROM, which
cannot be reprogrammed by the guest.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Many of the devices on the Musca board live behind TrustZone
Peripheral Protection Controllers (PPCs); add models of the
PPCs, using a similar scheme to the MPS2 board models.
This commit wires up the PPCs with "unimplemented device"
stubs behind them in the correct places in the address map.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The Musca-A and Musca-B1 development boards are based on the
SSE-200 subsystem for embedded. Implement an initial skeleton
model of these boards, which are similar but not identical.
This commit creates the board model with the SSE and the IRQ
splitters to wire IRQs up to its two CPUs. As yet there
are no devices and no memory: these will be added later.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The Musca boards have DAPLink firmware that sets the initial
secure VTOR value (the location of the vector table) differently
depending on the boot mode (from flash, from RAM, etc). Export
the init-svtor as a QOM property of the ARMSSE object so that
the board can change it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Coverity points out (CID 1398632, CID 1398650) that we
leak a couple of allocated strings in the error-exit
code path for setting up the MHUs in the ARMSSE.
Fix this bug by moving the allocate-and-free of each
string to be closer to the use, so we do the free before
doing the error-exit check.
Fixes: f8574705f6 ("hw/arm/armsse: Add unimplemented-device stubs for MHUs")
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190215113707.24553-1-peter.maydell@linaro.org
In commit 91c1e9fcbd where we added dual-CPU support to
the ARMSSE, we set up the wiring of the expansion IRQs via nested
loops: the outer loop on 'i' loops for each CPU, and the inner loop
on 'j' loops for each interrupt. Fix a typo which meant we were
wiring every expansion IRQ line to external IRQ 0 on CPU 0 and
to external IRQ 1 on CPU 1.
Fixes: 91c1e9fcbd ("hw/arm/armsse: Support dual-CPU configuration")
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
This will be needed by vhost-user-test, when each test switches to
its own GMainLoop and GMainContext. Otherwise, for a reconnecting
socket the initial connection will happen on the default GMainContext,
and no one will be listening on it.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20190202110834.24880-1-pbonzini@redhat.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
The arm_boot_info struct has a skip_dtb_autoload flag: if this is
set to true by the board code then arm_load_kernel() will not
load the DTB itself, but will leave this for the board code to
do itself later. However, the check for this is done in a
code path which is only executed for the case where we load
a kernel image file. If we're taking the "boot via firmware"
code path then the flag isn't honoured and the DTB is never
loaded.
We didn't notice this because the only real user of "boot
via firmware" that cares about the DTB is the virt board
(for UEFI boot), and that always wants skip_dtb_autoload
anyway. But the SBSA reference board model we're planning to
add will want the flag to behave correctly.
Now we've refactored the arm_load_kernel() function, the
fix is simple: drop the early 'return' so we fall into
the same "load the DTB" code the boot-direct-kernel path uses.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20190131112240.8395-6-peter.maydell@linaro.org
The code path for booting firmware doesn't set env->boot_info. At
first sight this looks odd, so add a comment saying why we don't.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20190131112240.8395-5-peter.maydell@linaro.org
Factor out the "boot via firmware" code path from arm_load_kernel()
into its own function.
This commit only moves code around; no semantic changes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20190131112240.8395-4-peter.maydell@linaro.org
Factor out the "direct kernel boot" code path from arm_load_kernel()
into its own function; this function is getting long enough that
the code flow is a bit confusing.
This commit only moves code around; no semantic changes.
We leave the "load the dtb" code in arm_load_kernel() -- this
is currently only used by the "direct kernel boot" path, but
this is a bug which we will fix shortly.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20190131112240.8395-3-peter.maydell@linaro.org
Fix the block comment style in arm_load_kernel() to QEMU's
current style preferences. This will allow us to do some
refactoring of this function without checkpatch complaining
about the code-motion patches.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20190131112240.8395-2-peter.maydell@linaro.org
Make ARM virt code configurable and the new CONFIG_ARM_VIRT
definitions added to the default-configs/arm-softmmu.mak.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190202072456.6468-8-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch adds an optional function pointer, 'elf_note_fn', to
load_elf() which causes load_elf() to additionally parse any
ELF program headers of type PT_NOTE and check to see if the ELF
Note is of the type specified by the 'translate_opaque' arg.
If a matching ELF Note is found then the specfied function pointer
is called to process the ELF note.
Passing a NULL function pointer results in ELF Notes being skipped.
The first consumer of this functionality is the PVHboot support
which needs to read the XEN_ELFNOTE_PHYS32_ENTRY ELF Note while
loading the uncompressed kernel binary in order to discover the
boot entry address for the x86/HVM direct boot ABI.
Signed-off-by: Liam Merwick <liam.merwick@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Until now, the set_pc logic was unclear, which raised questions about
whether it should be used directly, applying a value to PC or adding
additional checks, for example, set the Thumb bit in Arm cpu. Let's set
the set_pc logic for “Configure the PC, as was done in the ELF file”
and implement synchronize_with_tb hook for preserving PC to cpu_tb_exec.
Signed-off-by: Julia Suvorova <jusual@mail.ru>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190129121817.7109-1-jusual@mail.ru
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a model of the MPS2 FPGA image described in Application Note
AN521. This is identical to the AN505 image, except that it uses
the SSE-200 rather than the IoTKit and so has two Cortex-M33 CPUs.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-24-peter.maydell@linaro.org
In preparation for adding support for the AN521 MPS2 image, we need
to handle wiring up the MPS2 device interrupt lines to both CPUs in
the SSE-200, rather than just the one that the IoTKit has.
Abstract out a "connect to the IoTKit interrupt line" function
and make it connect to a splitter which feeds both sets of inputs
for the SSE-200 case.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-23-peter.maydell@linaro.org
Add a model of the SSE-200, now we have put in all
the code that lets us make it different from the IoTKit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-22-peter.maydell@linaro.org
Instantiate a copy of the CPU_IDENTITY register block for each CPU
in an SSE-200.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-21-peter.maydell@linaro.org
The SSE-200 has a "CPU local security control" register bank; add an
unimplemented-device stub for it. (The register bank has only one
interesting register, which allows the guest to lock down changes
to various CPU registers so they cannot be modified further. We
don't support that in our Cortex-M33 model anyway.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-19-peter.maydell@linaro.org
The SSE-200 gives each CPU a register bank to use to control its
L1 instruction cache. Put in an unimplemented-device stub for this.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-18-peter.maydell@linaro.org
Add unimplemented-device stubs for the various Power Policy Unit
devices that the SSE-200 has.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-17-peter.maydell@linaro.org
The SSE-200 has two Message Handling Units (MHUs), which sit behind
the APB PPC0. Wire up some unimplemented-device stubs for these,
since we don't yet implement a real model of this device.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-16-peter.maydell@linaro.org
The SYS_VERSION and SYS_CONFIG register values differ between the
IoTKit and SSE-200. Make them configurable via QOM properties rather
than hard-coded, and set them appropriately in the ARMSSE code that
instantiates the IOTKIT_SYSINFO device.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-15-peter.maydell@linaro.org
Create a cluster object to hold each CPU in the SSE. They are
logically distinct and may be configured differently (for instance
one may not have an FPU where the other does).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-14-peter.maydell@linaro.org
Give each CPU its own container memory region. This is necessary
for two reasons:
* some devices are instantiated one per CPU and the CPU sees only
its own device
* since a memory region can only be put into one container, we must
give each armv7m object a different MemoryRegion as its 'memory'
property, or a dual-CPU configuration will assert on realize when
the second armv7m object tries to put the MR into a container when
it is already in the first armv7m object's container
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-13-peter.maydell@linaro.org
The SSE-200 has two Cortex-M33 CPUs. These see the same view
of memory, with the exception of the "private CPU region" which
has per-CPU devices. Internal device interrupts for SSE-200
devices are mostly wired up to both CPUs, with the exception of
a few per-CPU devices. External GPIO inputs on the SSE-200
device are provided for the second CPU's interrupts above 32,
as is already the case for the first CPU.
Refactor the code to support creation of multiple CPUs.
For the moment we leave all CPUs with the same view of
memory: this will not work in the multiple-CPU case, but
we will fix this in the following commit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-12-peter.maydell@linaro.org
For the IoTKit the SRAM bank size is always 32K (15 bits); for the
SSE-200 this is a configurable parameter, which defaults to 32K but
can be changed when it is built into a particular SoC. For instance
the Musca-B1 board sets it to 128K (17 bits).
Make the bank size a QOM property. We follow the SSE-200 hardware in
naming the parameter SRAM_ADDR_WIDTH, which specifies the number of
address bits of a single SRAM bank.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-11-peter.maydell@linaro.org
The SSE-200 has four banks of SRAM, each with its own
Memory Protection Controller, where the IoTKit has only one.
Make the number of SRAM banks a field in ARMSSEInfo.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-10-peter.maydell@linaro.org
The SSE-200 has 4 banks of SRAM, each with its own internal
Memory Protection Controller. The interrupt status for these
extra MPCs appears in the same security controller SECMPCINTSTATUS
register as the MPC for the IoTKit's single SRAM bank. Enhance the
iotkit-secctl device to allow 4 MPCs. (If the particular IoTKit/SSE
variant in use does not have all 4 MPCs then the unused inputs will
simply result in the SECMPCINTSTATUS bits being zero as required.)
The hardcoded constant "1"s in armsse.c indicate the actual number
of SRAM MPCs the IoTKit has, and will be replaced in the following
commit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-9-peter.maydell@linaro.org
Rename the files that used to be iotkit.[ch] to
armsse.[ch] to reflect the fact they new cover
multiple Arm subsystems for embedded.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-8-peter.maydell@linaro.org
Rename various internal uses of 'iotkit' in hw/arm/iotkit.c to
'armsse', for consistency. The remaining occurences are:
* related to the devices TYPE_IOTKIT_SYSCTL, TYPE_IOTKIT_SYSINFO,
etc, which this refactor is not touching
* references that apply specifically to the IoTKit (like
the lack of a private CPU region)
* the vmstate, which keeps its old "iotkit" name for
migration compatibility reasons
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-7-peter.maydell@linaro.org
The Arm SSE-200 Subsystem for Embedded is a revised and
extended version of the older IoTKit SoC. Prepare for
adding a model of it by refactoring the IoTKit code into
an abstract base class which contains the functionality,
driven by a class data block specific to each subclass.
(This is the same approach used by the existing bcm283x
SoC family implementation.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-6-peter.maydell@linaro.org
The Arm IoTKit was effectively the forerunner of a series of
subsystems for embedded SoCs, named the SSE-050, SSE-100 and SSE-200:
https://developer.arm.com/products/system-design/subsystems
These are generally quite similar, though later iterations have
extra devices that earlier ones do not.
We want to add a model of the SSE-200, which means refactoring the
IoTKit code into an abstract base class and subclasses (using the
same design that the bcm283x SoC and Aspeed SoC family
implementations do). As a first step, rename the IoTKit struct and
QOM macros to ARMSSE, which is what we're going to name the base
class. We temporarily retain TYPE_IOTKIT to avoid changing the
code that instantiates a TYPE_IOTKIT device here and then changing
it back again when it is re-introduced as a subclass.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-5-peter.maydell@linaro.org
Expose "start-powered-off" as a property of the ARMv7M container,
which we just pass through to the CPU object in the same way that we
do for "init-svtor" and "idau". (We want this for the SSE-200, which
powers up only the first CPU at reset and leaves the second powered
down.)
As with the other CPU properties here, we can't just use alias
properties, because the CPU QOM object is not created until armv7m
realize time.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-4-peter.maydell@linaro.org
Rather than just creating the CPUs with object_new, make them child
objects of the armv7m container. This will allow the cluster code to
find the CPUs if an armv7m object is made a child of a cluster object.
object_new_with_props() will do the parenting for us.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-3-peter.maydell@linaro.org
Currently the ARMv7M NVIC object's realize method assumes that the
CPU the NVIC is attached to is CPU 0, because it thinks there can
only ever be one CPU in the system. To allow a dual-Cortex-M33
setup we need to remove this assumption; instead the armv7m
wrapper object tells the NVIC its CPU, in the same way that it
already tells the CPU what the NVIC is.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-2-peter.maydell@linaro.org
set object owner in memory_region_init_ram() instead
of NULL.
Signed-off-by: kumar sourav <sourav.jb1988@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190125155630.17430-1-sourav.jb1988@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently the cluster implementation doesn't have any constraints
on the ordering of realizing the TYPE_CPU_CLUSTER and populating it
with child objects. We want to impose a constraint that realize
must happen only after all the child objects are added, so move
the realize of rpu_cluster. (The apu_cluster is already
realized after child population.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20190121152218.9592-2-peter.maydell@linaro.org
If we aren't going to create any RPUs, then don't create the
rpu-cluster unit. This allows us to add an assertion to the
cluster object that it contains at least one CPU, which helps
to avoid bugs in creating clusters and putting CPUs in them.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190121184314.14311-1-peter.maydell@linaro.org
Recent microbit firmwares panic if the TWI magnetometer/accelerometer
devices are not detected during startup. We don't implement TWI (I2C)
so let's stub out these devices just to let the firmware boot.
Signed-off by: Steffen Görtz <contrib@steffen-goertz.de>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190110094020.18354-2-stefanha@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: fixed comment style]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Let's report IO-coherent access is supported for translation
table walks, descriptor fetches and queues by setting the COHACC
override flag. Without that, we observe wrong command opcodes.
The DT description also advertises the dma coherency.
Fixes a703b4f6c1 ("hw/arm/virt-acpi-build: Add smmuv3 node in IORT table")
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reported-by: Shameerali Kolothum Thodi <shameerali.kolothum.thodi@huawei.com>
Tested-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 20190107101041.765-1-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Most files that have TABs only contain a handful of them. Change
them to spaces so that we don't confuse people.
disas, standard-headers, linux-headers and libdecnumber are imported
from other projects and probably should be exempted from the check.
Outside those, after this patch the following files still contain both
8-space and TAB sequences at the beginning of the line. Many of them
have a majority of TABs, or were initially committed with all tabs.
bsd-user/i386/target_syscall.h
bsd-user/x86_64/target_syscall.h
crypto/aes.c
hw/audio/fmopl.c
hw/audio/fmopl.h
hw/block/tc58128.c
hw/display/cirrus_vga.c
hw/display/xenfb.c
hw/dma/etraxfs_dma.c
hw/intc/sh_intc.c
hw/misc/mst_fpga.c
hw/net/pcnet.c
hw/sh4/sh7750.c
hw/timer/m48t59.c
hw/timer/sh_timer.c
include/crypto/aes.h
include/disas/bfd.h
include/hw/sh4/sh.h
libdecnumber/decNumber.c
linux-headers/asm-generic/unistd.h
linux-headers/linux/kvm.h
linux-user/alpha/target_syscall.h
linux-user/arm/nwfpe/double_cpdo.c
linux-user/arm/nwfpe/fpa11_cpdt.c
linux-user/arm/nwfpe/fpa11_cprt.c
linux-user/arm/nwfpe/fpa11.h
linux-user/flat.h
linux-user/flatload.c
linux-user/i386/target_syscall.h
linux-user/ppc/target_syscall.h
linux-user/sparc/target_syscall.h
linux-user/syscall.c
linux-user/syscall_defs.h
linux-user/x86_64/target_syscall.h
slirp/cksum.c
slirp/if.c
slirp/ip.h
slirp/ip_icmp.c
slirp/ip_icmp.h
slirp/ip_input.c
slirp/ip_output.c
slirp/mbuf.c
slirp/misc.c
slirp/sbuf.c
slirp/socket.c
slirp/socket.h
slirp/tcp_input.c
slirp/tcpip.h
slirp/tcp_output.c
slirp/tcp_subr.c
slirp/tcp_timer.c
slirp/tftp.c
slirp/udp.c
slirp/udp.h
target/cris/cpu.h
target/cris/mmu.c
target/cris/op_helper.c
target/sh4/helper.c
target/sh4/op_helper.c
target/sh4/translate.c
tcg/sparc/tcg-target.inc.c
tests/tcg/cris/check_addo.c
tests/tcg/cris/check_moveq.c
tests/tcg/cris/check_swap.c
tests/tcg/multiarch/test-mmap.c
ui/vnc-enc-hextile-template.h
ui/vnc-enc-zywrle.h
util/envlist.c
util/readline.c
The following have only TABs:
bsd-user/i386/target_signal.h
bsd-user/sparc64/target_signal.h
bsd-user/sparc64/target_syscall.h
bsd-user/sparc/target_signal.h
bsd-user/sparc/target_syscall.h
bsd-user/x86_64/target_signal.h
crypto/desrfb.c
hw/audio/intel-hda-defs.h
hw/core/uboot_image.h
hw/sh4/sh7750_regnames.c
hw/sh4/sh7750_regs.h
include/hw/cris/etraxfs_dma.h
linux-user/alpha/termbits.h
linux-user/arm/nwfpe/fpopcode.h
linux-user/arm/nwfpe/fpsr.h
linux-user/arm/syscall_nr.h
linux-user/arm/target_signal.h
linux-user/cris/target_signal.h
linux-user/i386/target_signal.h
linux-user/linux_loop.h
linux-user/m68k/target_signal.h
linux-user/microblaze/target_signal.h
linux-user/mips64/target_signal.h
linux-user/mips/target_signal.h
linux-user/mips/target_syscall.h
linux-user/mips/termbits.h
linux-user/ppc/target_signal.h
linux-user/sh4/target_signal.h
linux-user/sh4/termbits.h
linux-user/sparc64/target_syscall.h
linux-user/sparc/target_signal.h
linux-user/x86_64/target_signal.h
linux-user/x86_64/termbits.h
pc-bios/optionrom/optionrom.h
slirp/mbuf.h
slirp/misc.h
slirp/sbuf.h
slirp/tcp.h
slirp/tcp_timer.h
slirp/tcp_var.h
target/i386/svm.h
target/sparc/asi.h
target/xtensa/core-dc232b/xtensa-modules.inc.c
target/xtensa/core-dc233c/xtensa-modules.inc.c
target/xtensa/core-de212/core-isa.h
target/xtensa/core-de212/xtensa-modules.inc.c
target/xtensa/core-fsf/xtensa-modules.inc.c
target/xtensa/core-sample_controller/core-isa.h
target/xtensa/core-sample_controller/xtensa-modules.inc.c
target/xtensa/core-test_kc705_be/core-isa.h
target/xtensa/core-test_kc705_be/xtensa-modules.inc.c
tests/tcg/cris/check_abs.c
tests/tcg/cris/check_addc.c
tests/tcg/cris/check_addcm.c
tests/tcg/cris/check_addoq.c
tests/tcg/cris/check_bound.c
tests/tcg/cris/check_ftag.c
tests/tcg/cris/check_int64.c
tests/tcg/cris/check_lz.c
tests/tcg/cris/check_openpf5.c
tests/tcg/cris/check_sigalrm.c
tests/tcg/cris/crisutils.h
tests/tcg/cris/sys.c
tests/tcg/i386/test-i386-ssse3.c
ui/vgafont.h
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20181213223737.11793-3-pbonzini@redhat.com>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Eric Blake <eblake@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Stefan Markovic <smarkovic@wavecomp.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
* Support u-boot 'noload' images for Arm (as used by NetBSD/evbarm GENERIC kernel)
* hw/misc/tz-mpc: Fix value of BLK_MAX register
* target/arm: Emit barriers for A32/T32 load-acquire/store-release insns
* nRF51 SoC: add timer, GPIO, RNG peripherals
* hw/arm/allwinner-a10: Add the 'A' SRAM and the SRAM controller
* cpus.c: Fix race condition in cpu_stop_current()
* hw/arm: versal: Plug memory leaks
* Allow M profile boards to run even if -kernel not specified
* gdbstub: Add multiprocess extension support for use when the
board has multiple CPUs of different types (like the Xilinx Zynq boards)
* target/arm: Don't decode S bit in SVE brk[ab] merging insns
* target/arm: Convert ARM_TBFLAG_* to FIELDs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABCAAGBQJcM36AAAoJEDwlJe0UNgzepuMP/A6umcXRrO+vOZgkW+cvJ8cD
JkDdb8H/u3S6zqNokABI3Ya/areX1P30sRV7e7mC5IsknVNZe0MqQX6TW5477HMP
Oz/m1AbyByWMLVILFiWfte5dtRRLfs3axzrmhu6HwJXe0NIUiYQofoJzCZEDMxDn
71cehgeNkUGA36HViPyqzHZYADFkCX3Tfmh1FEh2jD7taK9GNsff8p6cHTb05W7d
wWk68PS8VKTb5VrYH6SyiAHW8gBVrrUkYlkPKHzemK5fwlgDOSfxVLthf8mo08SH
QxEXI430tagdmrGNO/nKOTA2NQwMzvCk/OLf0Qwg9I9F9pYtiOJ7nXXbtqDC8eKy
DdHsL57W0F7sFkoVt+YNHSeylyLRluDh+D+Q7OHnlvwsEYmecqsWkW/A2CYC0uWs
8ajxPBNpGG1lIvo63YK5/4kOy0DE/6ISljYOSlYYg3iXeAZPkQZMTlUxoYmJQ+Zr
h1tLg1N9SuyQK5g5Uuluw2GwgzIv/Bt1LFo7pnvsA2X6PKiv6nno40T8q0Lw6ah4
lmAUWx0OUilTrvQwterHlr6hfWu2RLiRoxCg06a3C93YlRjsR3vZOBeQ5ByaE+ho
5ItKn58EerO+UaweVoc6MDhJFPC8b16Eee281BCec8Ks4GR1tIcpP/0z2lUwhBu6
hoPmkoPtFtu1dKBgF8Ma
=x1jv
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20190107' into staging
target-arm queue:
* Support u-boot 'noload' images for Arm (as used by NetBSD/evbarm GENERIC kernel)
* hw/misc/tz-mpc: Fix value of BLK_MAX register
* target/arm: Emit barriers for A32/T32 load-acquire/store-release insns
* nRF51 SoC: add timer, GPIO, RNG peripherals
* hw/arm/allwinner-a10: Add the 'A' SRAM and the SRAM controller
* cpus.c: Fix race condition in cpu_stop_current()
* hw/arm: versal: Plug memory leaks
* Allow M profile boards to run even if -kernel not specified
* gdbstub: Add multiprocess extension support for use when the
board has multiple CPUs of different types (like the Xilinx Zynq boards)
* target/arm: Don't decode S bit in SVE brk[ab] merging insns
* target/arm: Convert ARM_TBFLAG_* to FIELDs
# gpg: Signature made Mon 07 Jan 2019 16:29:52 GMT
# gpg: using RSA key 3C2525ED14360CDE
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>"
# gpg: aka "Peter Maydell <pmaydell@gmail.com>"
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>"
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20190107: (37 commits)
Support u-boot noload images for arm as used by, NetBSD/evbarm GENERIC kernel.
hw/misc/tz-mpc: Fix value of BLK_MAX register
target/arm: Emit barriers for A32/T32 load-acquire/store-release insns
arm: Add Clock peripheral stub to NRF51 SOC
tests/microbit-test: Add Tests for nRF51 Timer
arm: Instantiate NRF51 Timers
hw/timer/nrf51_timer: Add nRF51 Timer peripheral
tests/microbit-test: Add Tests for nRF51 GPIO
arm: Instantiate NRF51 general purpose I/O
hw/gpio/nrf51_gpio: Add nRF51 GPIO peripheral
arm: Instantiate NRF51 random number generator
hw/misc/nrf51_rng: Add NRF51 random number generator peripheral
arm: Add header to host common definition for nRF51 SOC peripherals
qtest: Add set_irq_in command to set IRQ/GPIO level
hw/arm/allwinner-a10: Add the 'A' SRAM and the SRAM controller
cpus.c: Fix race condition in cpu_stop_current()
MAINTAINERS: Add ARM-related files for hw/[misc|input|timer]/
hw/arm: versal: Plug memory leaks
Revert "armv7m: Guard against no -kernel argument"
arm/xlnx-zynqmp: put APUs and RPUs in separate CPU clusters
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
noload kernels are loaded with the u-boot image header and as a result
the header size needs adding to the entry point. Fake up a hdr so the
kernel image is loaded at the right address and the entry point is
adjusted appropriately.
The default location for the uboot file is 32MiB above bottom of DRAM.
This matches the recommendation in Documentation/arm/Booting.
Clarify the load_uimage API to state the passing of a load address when an
image doesn't specify one, or when loading a ramdisk is expected.
Adjust callers of load_uimage, etc.
Signed-off-by: Nick Hudson <skrll@netbsd.org>
Message-id: 11488a08-1fe0-a278-2210-deb64731107f@gmx.co.uk
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Thomas Huth
Markus Armbruster
Joel Stanley
Peter Maydell
Philippe Mathieu-Daudé
Eric Auger
Cornelia Huck
Wei Yang
Kővágó, Zoltán
Paolo Bonzini
Michel Heily
Shameer Kolothum
Corey Minyard
Yang Zhong
Liam Merwick
Steffen Görtz
Julia Suvorova
kumar sourav
Nick Hudson