If dropping packets, data is freed, the caller's loop should not continue.
Reported by ccc-analyzer.
Signed-off-by: Fam Zheng <famz@redhat.com>
Message-id: 1456301288-1592-1-git-send-email-famz@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This quirk is a workaround for the following hardware behaviour, on
which UEFI (specifically, the bootloader for Windows on Pi2) depends:
1. at boot with an SD card present, the interrupt status/enable
registers are initially zero
2. upon enabling it in the interrupt enable register, the card insert
bit in the interrupt status register is immediately set
3. after a subsequent controller reset, the card insert interrupt does
not fire, even if enabled in the interrupt enable register
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Message-id: 1456436130-7048-3-git-send-email-Andrew.Baumann@microsoft.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This reverts commit 723697551a.
This change was poorly tested on my part. It squelched card insertion
interrupts on reset, but that was not necessary because sdhci_reset()
clears all the registers (via the call to memset), so the subsequent
sdhci_insert_eject_cb() call never sees the card insert interrupt
enabled. However, not calling the insert_eject_cb results in prnsts
remaining 0, when it actually needs to be updated to indicate card
presence and R/O status.
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Message-id: 1456436130-7048-2-git-send-email-Andrew.Baumann@microsoft.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Recent changes to sdhci broke SD on raspi. This change mirrors
the logic to create the SD card device at the board level.
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Message-id: 1456351128-5560-1-git-send-email-Andrew.Baumann@microsoft.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
pl061.c emulates two GPIO devices, ARM PL061 and TI Stellaris, which
share the same read/write functions (pl061_read and pl061_write).
However PL061 and Stellaris have different GPIO register definitions
and pl061_read()/pl061_write() doesn't check it. This patch enforces
checking on offset, preventing R/W into the reserved memory area.
Signed-off-by: Wei Huang <wei@redhat.com>
Message-id: 1455814580-17699-1-git-send-email-wei@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fixes all over the place.
virtio dataplane migration support.
Old q35 machine types removed.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWzuKeAAoJECgfDbjSjVRpGzIH/1Tz6CoEq1rowiyVJ9B80oQU
gDI2YWnJDSwJllmAF0rmoPRBQR8op3ZETZiCAcADHoZ7kdBNWGbyQeaDrrEPH7Q/
rCDVt8Q3g80vs89aWKG0nQ16J2MW5TbkuiQw7pjQSdc9AbUdWpUqSiWnpZ+sPAql
6DuVpjQ4/rN2alucXoa1Sir8KDDV7kBuY8U6/KoY890qzh842dv2523qvuCza9yR
KX8Imj3oQAFjFSv5t1aOD3yYvWFd73EsReHPLGb1JtsVr/6wjs0sFUyA3JicBgnT
+kWoSObWikfDY69HnqTkJpkun6woMM3zW5h2SkUBf9QP3yqLfGIp9uSriNN84Ak=
=KXyh
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
vhost, virtio, pci, pc
Fixes all over the place.
virtio dataplane migration support.
Old q35 machine types removed.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Thu 25 Feb 2016 11:16:46 GMT using RSA key ID D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
* remotes/mst/tags/for_upstream: (21 commits)
q35: No need to check gigabyte_align
q35: Remove unused q35-acpi-dsdt.aml file
ich9: Remove enable_tco arguments from init functions
machine: Remove no_tco field
q35: Remove old machine versions
tests/vhost-user-bridge: fix build on 32 bit systems
vring: remove
virtio-scsi: do not use vring in dataplane
virtio-blk: do not use vring in dataplane
virtio-blk: fix "disabled data plane" mode
virtio: export vring_notify as virtio_should_notify
virtio: add AioContext-specific function for host notifiers
vring: make vring_enable_notification return void
block-migration: acquire AioContext as necessary
pci core: function pci_bus_init() cleanup
pci core: function pci_host_bus_register() cleanup
balloon: Use only 'pc-dimm' type dimm for ballooning
virtio-balloon: rewrite get_current_ram_size()
move get_current_ram_size to virtio-balloon.c
vhost-user: don't merge regions with different fds
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
gigabyte_align is always true on q35, so we don't need the
!gigabyte_align compat code anymore.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
The file was used only by older machine-types, and it is not
needed anymore.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
The enable_tco arguments are always true, so they are not needed
anymore.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
The field is always set to zero, so it is not necessary anymore.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Migration with q35 was not possible before commit
04329029a8, because q35
unconditionally creates an ich9-ahci device, that was marked as
unmigratable. So all q35 machine classes before pc-q35-2.4 were
not migratable, so there's no point in keeping compatibility code
for them.
Remove all old pc-q35 machine classes and keep only pc-q35-2.4
and newer.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
In disabled mode, virtio-blk dataplane seems to be enabled, but flow
actually goes through the normal virtio path. This patch simplifies a bit
the handling of disabled mode. In disabled mode, virtio_blk_handle_output
might be called even if s->dataplane is not NULL.
This is a bit tricky, because the current check for s->dataplane will
always trigger, causing a continuous stream of calls to
virtio_blk_data_plane_start. Unfortunately, these calls will not
do anything. To fix this, set the "started" flag even in disabled
mode, and skip virtio_blk_data_plane_start if the started flag is true.
The resulting changes also prepare the code for the next patch, were
virtio-blk dataplane will reuse the same virtio_blk_handle_output function
as "regular" virtio-blk.
Because struct VirtIOBlockDataPlane is opaque in virtio-blk.c, we have
to move s->dataplane->started inside struct VirtIOBlock.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Virtio dataplane needs to trigger the irq manually through the
guest notifier. Export virtio_should_notify so that it can be
used around event_notifier_set.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
This is used to register ioeventfd with a dataplane thread.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Make the API more similar to the regular virtqueue API. This will
help when modifying the code to not use vring.c anymore.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
remove unused param
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
remove unused param, and rename the other to a meaningful one.
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
For now there are only two dimm's: pc-dimm and nvdimm. This patch is
actually needed to disable ballooning on nvdimm. But, to avoid future
bugs, instead of disallowing nvdimm, we allow only pc-dimm. So, if
someone adds new dimm which should be balloon-able, then this ability
should be explicitly specified here.
Why ballooning for nvdimm should be disabled for now:
NVDIMM for now is planned to use as a backing store for DAX filesystem
in the guest and thus this memory is excluded from guest memory
management and LRUs.
In this case libvirt running QEMU along with configured balloon almost
immediately inflates balloon and effectively kill the guest as
qemu counts nvdimm as part of the ram.
Counting dimm devices as part of the ram for ballooning was started from
commit 463756d03:
virtio-balloon: Fix balloon not working correctly when hotplug memory
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Use pc_dimm_built_list() instead of qmp_pc_dimm_device_list()
Actually, Qapi is not related to this internal helper.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This fixes a crash in the target QEMU during migration.
Broken in commit c5f54f3.
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[reworded commit message]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This hypercall either initializes a page with zeros, or copies
another page.
According to LoPAPR, the i-cache of the page should also be
flushed if using H_ICACHE_INVALIDATE or H_ICACHE_SYNCHRONIZE,
and the d-cache should be synchronized to the RAM if the
H_ICACHE_SYNCHRONIZE flag is used. For this, two new functions
are introduced, kvmppc_dcbst_range() and kvmppc_icbi()_range, which
use the corresponding assembler instructions to flush the caches
if running with KVM on Power. If the code runs with TCG instead,
the code only uses tb_flush(), assuming that this will be
enough for synchronization.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
---
This just catches a couple of stragglers since I posted
the last clean-includes patchset last week.
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
get_current_ram_size() is used only in virtio-balloon.c
This patch moves it into virtio-balloon and make it static, to allow
some balloon-specific tuning.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
vhost currently merges regions with contiguious virtual and physical
addresses. This breaks for vhost-user since that also needs fds to
match.
Add a vhost_ops entry to compare the fds for vhost-user only.
Cc: qemu-stable@nongnu.org
Cc: Victor Kaplansky <victork@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
While guest/host ABI is documented in hw/acpi/bios-linker-loader.c,
the API was left undocumented.
This adds documentation for all API functions.
Additionally, input is validated to make sure all
pointers fall within range of provided files.
To allow this validation for checksum commands,
bios_linker_loader_add_checksum is changed to accept GArray * in place
of void *.
Reported-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Allocate timer once, at init time, instead of allocating/freeing
it all the time when starting/stopping the bus. Simplifies the
code, also fixes bugs (memory leak) due to missing checks whenever
the time is already allocated or not.
Cc: Prasad J Pandit <pjp@fedoraproject.org>
Reported-by: Zuozhi Fzz <zuozhi.fzz@alibaba-inc.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
pid can be gotten from uhci device memory in uhci_handle_td(),
so the guest can trigger assert qemu if we get an invalid pid.
And the uhci spec 2.1.2 tells us The Host Controller sets Host
Controller Process Error bit to 1 when it detects a fatal error
and indicates that the Host Controller suffered a consistency
check failure while processing a Transfer Descriptor. An example
of a consistency check failure would be finding an illegal PID
field while processing the packet header portion of the TD.
When this error occurs, the Host Controller clears the Run/Stop
bit in the Command register to prevent further schedule execution.
We'd better to set UHCI_STS_HCPERR and kick an interrupt, check
the pid value at the first of uhci_handle_td function.
https://bugzilla.redhat.com/show_bug.cgi?id=1070027
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Message-id: 1455867238-4720-1-git-send-email-arei.gonglei@huawei.com
[ applied minor codestyle fix ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
When processing remote NDIS control message packets,
the USB Net device emulator uses a fixed length(4096) data buffer.
The incoming informationBufferOffset & Length combination could
overflow and cross that range. Check control message buffer
offsets and length to avoid it.
Reported-by: Qinghao Tang <luodalongde@gmail.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-id: 1455648821-17340-3-git-send-email-ppandit@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
When processing remote NDIS control message packets, the USB Net
device emulator uses a fixed length(4096) data buffer. The incoming
packet length could exceed this limit. Add a check to avoid it.
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-id: 1455648821-17340-2-git-send-email-ppandit@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The TUSB6010 is a USB controller (as the name suggests). Move it from
hw/timer (where it was accidentally filed in 2013 when we moved
everything out of hw/) to hw/usb.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1455883404-10976-1-git-send-email-peter.maydell@linaro.org
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
When processing remote NDIS control message packets, the USB Net
device emulator checks to see if the USB configuration descriptor
object is of RNDIS type(2). But it does not check if it is null,
which leads to a null dereference error. Add check to avoid it.
Reported-by: Qinghao Tang <luodalongde@gmail.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-id: 1455188480-14688-1-git-send-email-ppandit@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Even PCI_CAP_FLAGS has the same value as PCI_MSIX_FLAGS, the later one is
the more proper on retrieving MSIX entries.
This patch uses PCI_MSIX_FLAGS to retrieve the MSIX entries.
Signed-off-by: Wei Yang <richard.weiyang@gmail.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
qemu_fdt_setprop asserts in case of error hence no need to check
the returned value.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This patch allows the instantiation of the vfio-amd-xgbe device
from the QEMU command line (-device vfio-amd-xgbe,host="<device>").
The guest is exposed with a device tree node that combines the description
of both XGBE and PHY (representation supported from 4.2 onwards kernel):
Documentation/devicetree/bindings/net/amd-xgbe.txt.
There are 5 register regions, 6 interrupts including 4 optional
edge-sensitive per-channel interrupts.
Some property values are inherited from host device tree. Host device tree
must feature a combined XGBE/PHY representation (>= 4.2 host kernel).
2 clock nodes (dma and ptp) also are created. It is checked those clocks
are fixed on host side.
AMD XGBE node creation function has a dependency on vfio Linux header and
more generally node creation function for VFIO platform devices only make
sense with CONFIG_LINUX so let's protect this code with #ifdef CONFIG_LINUX.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Some passthrough'ed devices depend on clock nodes. Those need to be
generated in the guest device tree. This patch introduces some helpers
to build a clock node from information retrieved in the host device tree.
- copy_properties_from_host copies properties from a host device tree
node to a guest device tree node
- fdt_build_clock_node builds a guest clock node and checks the host
fellow clock is a fixed one.
fdt_build_clock_node will become static as soon as it gets used. A
dummy pre-declaration is needed for compilation of this patch.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This patch aligns the prototype with qemu_fdt_getprop. The caller
can choose whether the function self-asserts on error (passing
&error_fatal as Error ** argument, corresponding to the legacy behavior),
or behaves differently such as simply output a message.
In this later case the caller can use the new lenp parameter to interpret
the error if any.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This patch introduces the amd-xgbe VFIO platform device. It
allows the guest to do passthrough on a device exposing an
"amd,xgbe-seattle-v1a" compat string.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Use the macro PCI_CAP_LIST_NEXT instead of 1, so that the code would be
more self-explain.
This patch makes this change and also fixs one typo in comment.
Signed-off-by: Wei Yang <richard.weiyang@gmail.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
For vfio device, we need to propagate the aer error to
Guest OS. we use the pcie_aer_msg() to send aer error
to guest.
Signed-off-by: Chen Fan <chen.fan.fnst@cn.fujitsu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
pcie_aer_init was used to emulate an aer capability for pcie device,
but for vfio device, the aer config space size is mutable and is not
always equal to PCI_ERR_SIZEOF(0x48). it depends on where the TLP Prefix
register required, so here we add a size argument.
Signed-off-by: Chen Fan <chen.fan.fnst@cn.fujitsu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
this function search the capability from the end, the last
size should 0x100 - pos, not 0xff - pos.
Signed-off-by: Chen Fan <chen.fan.fnst@cn.fujitsu.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Device's Offset and size can reach PCIE_CONFIG_SPACE_SIZE,
fix the corresponding assert.
Signed-off-by: Chen Fan <chen.fan.fnst@cn.fujitsu.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Fixes all over the place.
New tests for pxe.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWxedfAAoJECgfDbjSjVRp9ZoH/1zlxDy/iiJWXJI0jkcnbSof
/tFbchrj/hfz0/Wr0yeKJNdU1rMgiY0lYM1F5Pp4MQDHFoFM6i7LaLUYLQq92u+w
CpgTOMXwthOqn94yrBncKUN+OkB4vDW18sHd21rTh5n1oO9VjM4oQFSHpAtaDdnc
7dyryrlocBlgjARuOhW7A3KJAdPcKUer5JKdbWMDHw2wgwk1+7lx8ip7PBrFpMwW
PEEw2jo/lQw/rm/Kit+BV43NBy5pks2/jWmaXqH5jgCNixEmbY150dJLLW6lAqdh
xatnMxkQHpbEyf/Cy8M73v8vdOLjfQNdJ7GO0lc3CZw4bZBHbOcuzVEExvHewYw=
=vpiH
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
vhost, virtio, pci, pxe
Fixes all over the place.
New tests for pxe.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Thu 18 Feb 2016 15:46:39 GMT using RSA key ID D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
* remotes/mst/tags/for_upstream:
tests/vhost-user-bridge: add scattering of incoming packets
vhost-user interrupt management fixes
rules: filter out irrelevant files
change type of pci_bridge_initfn() to void
dec: convert to realize()
tests: add pxe e1000 and virtio-pci tests
msix: fix msix_vector_masked
virtio: optimize virtio_access_is_big_endian() for little-endian targets
vhost: simplify vhost_needs_vring_endian()
vhost: move virtio 1.0 check to cross-endian helper
virtio: move cross-endian helper to vhost
vhost-net: revert support of cross-endian vnet headers
virtio-net: use the backend cross-endian capabilities
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* split the old SysBus init function into an instance_init
and a Device realize function
* use DeviceClass::realize instead of SysBusDeviceClass::init
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
assign pl031_init to pl031_info.instance_init and drop the
SysBusDeviceClass::init
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
