Section 3.4.1 of the datasheet says,
The alignment of the RRA is confined to either word or long word
boundaries, depending upon the data width mode. In 16-bit mode,
the RRA must be aligned to a word boundary (A0 is always zero)
and in 32-bit mode, the RRA is aligned to a long word boundary
(A0 and A1 are always zero).
This constraint has been implemented for 16-bit mode; implement it
for 32-bit mode too.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
A received packet consumes pkt_size bytes in the buffer and the frame
checksum that's appended to it consumes another 4 bytes. The Receive
Buffer Address register takes the former quantity into account but
not the latter. So the next packet written to the buffer overwrites
the frame checksum. Fix this.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Add a bounds check to prevent a large packet from causing a buffer
overflow. This is defensive programming -- I haven't actually tried
sending an oversized packet or a jumbo ethernet frame.
The SONIC handles packets that are too big for the buffer by raising
the RBAE interrupt and dropping them. Linux uses that interrupt to
count dropped packets.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Jason Wang <jasowang@redhat.com>
It doesn't make sense to clear the command register bit unless the
command was actually issued.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Follow the algorithm given in the National Semiconductor DP83932C
datasheet in section 3.4.7:
At the next reception, the SONIC re-reads the last RXpkt.link field,
and updates its CRDA register to point to the next descriptor.
The chip is designed to allow the host to provide a new list of
descriptors in this way.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This function re-uses its 'size' argument as a scratch variable.
Instead, declare a local 'size' variable for that purpose so that the
function result doesn't get messed up.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Jason Wang <jasowang@redhat.com>
According to the datasheet, section 3.4.4, "in 32-bit mode ... the SONIC
always writes long words".
Therefore, use the same technique for the 'in_use' field that is used
everywhere else, and write the full long word.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The DP83932 and DP83934 have 32 data lines. The datasheet says,
Data Bus: These bidirectional lines are used to transfer data on the
system bus. When the SONIC is a bus master, 16-bit data is transferred
on D15-D0 and 32-bit data is transferred on D31-D0. When the SONIC is
accessed as a slave, register data is driven onto lines D15-D0.
D31-D16 are held TRI-STATE if SONIC is in 16-bit mode. If SONIC is in
32-bit mode, they are driven, but invalid.
Always use 32-bit accesses both as bus master and bus slave.
Force the MSW to zero in bus master mode.
This gets the Linux 'jazzsonic' driver working, and avoids the need for
prior hacks to make the NetBSD 'sn' driver work.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The Least Significant bit of a descriptor address register is used as
an EOL flag. It has to be masked when the register value is to be used
as an actual address for copying memory around. But when the registers
are to be updated the EOL bit should not be masked.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Jason Wang <jasowang@redhat.com>
In our KVM GICv2 realize function, we try to cope with old kernels
that don't provide the device control API (KVM_CAP_DEVICE_CTRL): we
try to use the device control, and if that fails we fall back to
assuming that the kernel has the old style KVM_CREATE_IRQCHIP and
that it will provide a GICv2.
This doesn't cater for the possibility of a kernel and hardware which
only provide a GICv3, which is very common now. On that setup we
will abort() later on in kvm_arm_pmu_set_irq() when we try to wire up
an interrupt to the GIC we failed to create:
qemu-system-aarch64: PMU: KVM_SET_DEVICE_ATTR: Invalid argument
qemu-system-aarch64: failed to set irq for PMU
Aborted
If the kernel advertises KVM_CAP_DEVICE_CTRL we should trust it if it
says it can't create a GICv2, rather than assuming it has one. We
can then produce a more helpful error message including a hint about
the most probable reason for the failure.
If the kernel doesn't advertise KVM_CAP_DEVICE_CTRL then it is truly
ancient by this point but we might as well still fall back to a
KVM_CREATE_IRQCHIP GICv2.
With this patch then the user misconfiguration which previously
caused an abort now prints:
qemu-system-aarch64: Initialization of device kvm-arm-gic failed: error creating in-kernel VGIC: No such device
Perhaps the host CPU does not support GICv2?
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Tested-by: Andrew Jones <drjones@redhat.com>
Message-id: 20200225182435.1131-1-peter.maydell@linaro.org
Xilinx USB devices are now instantiated through TYPE_CHIPIDEA,
and xlnx support in the EHCI code is no longer needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20200215122354.13706-3-linux@roeck-us.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
USB ports on Xilinx Zync must be instantiated as TYPE_CHIPIDEA to work.
Linux expects and checks various chipidea registers, which do not exist
with the basic ehci emulation. This patch series fixes the problem.
Without this patch, USB ports fail to instantiate under Linux.
ci_hdrc ci_hdrc.0: doesn't support host
ci_hdrc ci_hdrc.0: no supported roles
With this patch, USB ports are instantiated, and it is possible
to boot from USB drive.
ci_hdrc ci_hdrc.0: EHCI Host Controller
ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1
ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00
usb 1-1: new full-speed USB device number 2 using ci_hdrc
usb 1-1: not running at top speed; connect to a high speed hub
usb 1-1: config 1 interface 0 altsetting 0 endpoint 0x81 has invalid maxpacket 512, setting to 64
usb 1-1: config 1 interface 0 altsetting 0 endpoint 0x2 has invalid maxpacket 512, setting to 64
usb-storage 1-1:1.0: USB Mass Storage device detected
scsi host0: usb-storage 1-1:1.0
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20200215122354.13706-2-linux@roeck-us.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use this in the places that were checking ARM_FEATURE_VFP, and
are obviously testing for the existance of the register set
as opposed to testing for some particular instruction extension.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20200224222232.13807-2-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The GIC built into the ARM11MPCore is always implemented with 4
priority bits; set the GIC property accordingly.
Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1582537164-764-4-git-send-email-sai.pavan.boddu@xilinx.com
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: tweaked commit message]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
All A9 CPUs have a GIC with 5 bits of priority.
Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1582537164-764-3-git-send-email-sai.pavan.boddu@xilinx.com
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The GICv2 allows the implementation to implement a variable number
of priority bits; unimplemented bits in the priority registers
are read as zeros, writes ignored. We were previously always
implementing a full 8 bits of priority, which is allowed but not
what the real hardware typically does (which is usually to have
4 or 5 bits of priority).
Add a new device property to allow the number of implemented
property bits to be specified.
Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Message-id: 1582537164-764-2-git-send-email-sai.pavan.boddu@xilinx.com
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: improved commit message]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Linux kernel displays errors why trying to detect the PL041
audio interface:
Linux version 4.16.0 (linus@genomnajs) (gcc version 7.2.1 20171011 (Linaro GCC 7.2-2017.11)) #142 PREEMPT Wed May 9 13:24:55 CEST 2018
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00093177
CPU: VIVT data cache, VIVT instruction cache
OF: fdt: Machine model: ARM Integrator/CP
...
OF: amba_device_add() failed (-19) for /fpga/aaci@1d000000
Since we have it already modelled, simply plug it.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200223233033.15371-2-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This uses TYPE_PL011 when creating the serial port so that the code
looks cleaner.
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20200224222223.4128-1-gshan@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* fix for xen-block
* fix in exec.c for migration of xen guest
* one cleanup patch
-----BEGIN PGP SIGNATURE-----
iQFOBAABCgA4FiEE+AwAYwjiLP2KkueYDPVXL9f7Va8FAl5XrpgaHGFudGhvbnku
cGVyYXJkQGNpdHJpeC5jb20ACgkQDPVXL9f7Va88wQf/TcU/rOJSIlTzIoIktp+T
uvsb3+TkppdLBeFvAPAfKXFG8JxO7RHxtnn7pZFdlejqNG+AJhARd+LbQMPMO15d
cLo7Da5HE8ni9f+CwtY61SNS3qe1+8qoNRFwxeycA5pfr+XZb5dB8FYW4w5H4mg0
gyf4R0kb/5Y43K4FKEu/09rh3jtV1HqVfbjMrk3u82sex5gp3LT9kg6VJyrGE3rr
D/rmVOM1+rEn8S9e5YG1YqBq1HRSMAbrQ3kvkCJPHE+vLnmkbITyi9faL99vR3Pl
oTtmnwNWUwYzf/FwAA+8/YaaAsEz17KQXOQtFxIC+j9im2KkE5waD15AfEJ5eQgW
EA==
=sKMx
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/aperard/tags/pull-xen-20200227' into staging
Xen queue 2020-02-27
* fix for xen-block
* fix in exec.c for migration of xen guest
* one cleanup patch
# gpg: Signature made Thu 27 Feb 2020 11:57:12 GMT
# gpg: using RSA key F80C006308E22CFD8A92E7980CF5572FD7FB55AF
# gpg: issuer "anthony.perard@citrix.com"
# gpg: Good signature from "Anthony PERARD <anthony.perard@gmail.com>" [marginal]
# gpg: aka "Anthony PERARD <anthony.perard@citrix.com>" [marginal]
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 5379 2F71 024C 600F 778A 7161 D8D5 7199 DF83 42C8
# Subkey fingerprint: F80C 0063 08E2 2CFD 8A92 E798 0CF5 572F D7FB 55AF
* remotes/aperard/tags/pull-xen-20200227:
Memory: Only call ramblock_ptr when needed in qemu_ram_writeback
xen-bus/block: explicitly assign event channels to an AioContext
hw/xen/xen_pt_load_rom: Remove unused includes
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Acked-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Acked-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
This will store the compression method to use. We start with none.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Acked-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
---
Rename multifd-method to multifd-compression
This commit was produced with the Coccinelle script
scripts/coccinelle/memory-region-housekeeping.cocci.
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Message-Id: <20200224205533.23798-8-philmd@redhat.com>
Since commit d8ed887bdc, the cpu_mips_irq_request handler takes
a pointer to MIPSCPU in its opaque argument. Directly pass the
cpu pointer.
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Message-Id: <20200221162011.26383-1-philmd@redhat.com>
It is not safe to close an event channel from the QEMU main thread when
that channel's poller is running in IOThread context.
This patch adds a new xen_device_set_event_channel_context() function
to explicitly assign the channel AioContext, and modifies
xen_device_bind_event_channel() to initially assign the channel's poller
to the QEMU main thread context. The code in xen-block's dataplane is
then modified to assign the channel to IOThread context during
xen_block_dataplane_start() and de-assign it during in
xen_block_dataplane_stop(), such that the channel is always assigned
back to main thread context before it is closed. aio_set_fd_handler()
already deals with all the necessary synchronization when moving an fd
between AioContext-s so no extra code is needed to manage this.
Reported-by: Julien Grall <jgrall@amazon.com>
Signed-off-by: Paul Durrant <pdurrant@amazon.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Message-Id: <20191216143451.19024-1-pdurrant@amazon.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
xen_pt_load_rom.c does not use any of these includes, remove them.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Message-Id: <20191014142246.4538-9-philmd@redhat.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Let's rename PSW_MASK_ESA_ADDR to PSW_MASK_SHORT_ADDR because we're
not working with a ESA PSW which would not support the extended
addressing bit. Also let's actually use it.
Additionally we introduce PSW_MASK_SHORT_CTRL and use it throughout
the codebase.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Message-Id: <20200227092341.38558-1-frankja@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The current vhost_user_set_mem_table_postcopy() implementation
populates each region of the VHOST_USER_SET_MEM_TABLE message without
first checking if there are more than VHOST_MEMORY_MAX_NREGIONS already
populated. This can cause memory corruption if too many regions are
added to the message during the postcopy step.
This change moves an existing assert up such that attempting to
construct a VHOST_USER_SET_MEM_TABLE message with too many memory
regions will gracefully bring down qemu instead of corrupting memory.
Signed-off-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Signed-off-by: Peter Turschmid <peter.turschm@nutanix.com>
Message-Id: <1579143426-18305-2-git-send-email-raphael.norwitz@nutanix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When multiqueue is enabled, a vhost_dev is created for each queue
pair. However, only one slave channel is needed.
Fixes: 4bbeeba023 (vhost-user: add slave-req-fd support)
Cc: marcandre.lureau@redhat.com
Signed-off-by: Adrian Moreno <amorenoz@redhat.com>
Message-Id: <20200121214553.28459-1-amorenoz@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Adds the "virtio,pci-iommu" node in the host bridge node and
the RID mapping, excluding the IOMMU RID.
This is done in the virtio-iommu-pci hotplug handler which
gets called only if no firmware is loaded or if -no-acpi is
passed on the command line. As non DT integration is
not yet supported by the kernel we must make sure we
are in DT mode. This limitation will be removed as soon
as the topology description feature gets supported.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <20200214132745.23392-10-eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds virtio-iommu-pci, which is the pci proxy for
the virtio-iommu device.
Currently non DT integration is not yet supported by the kernel.
So the machine must implement a hotplug handler for the
virtio-iommu-pci device that creates the device tree iommu-map
bindings as documented in kernel documentation:
Documentation/devicetree/bindings/virtio/iommu.txt
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20200214132745.23392-9-eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add Migration support. We rely on recently added gtree and qlist
migration. We only migrate the domain gtree. The endpoint gtree
is re-constructed in a post-load operation.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Acked-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20200214132745.23392-8-eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The event queue allows to report asynchronous errors.
The translate function now injects faults when relevant.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20200214132745.23392-7-eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch implements the translate callback
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20200214132745.23392-6-eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch implements virtio_iommu_map/unmap.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20200214132745.23392-5-eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch implements the endpoint attach/detach to/from
a domain.
Domain and endpoint internal datatypes are introduced.
Both are stored in RB trees. The domain owns a list of
endpoints attached to it. Also helpers to get/put
end points and domains are introduced.
As for the IOMMU memory regions, a callback is called on
PCI bus enumeration that initializes for a given device
on the bus hierarchy an IOMMU memory region. The PCI bus
hierarchy is stored locally in IOMMUPciBus and IOMMUDevice
objects.
At the time of the enumeration, the bus number may not be
computed yet.
So operations that will need to retrieve the IOMMUdevice
and its IOMMU memory region from the bus number and devfn,
once the bus number is garanteed to be frozen, use an array
of IOMMUPciBus, lazily populated.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20200214132745.23392-4-eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch adds the command payload decoding and
introduces the functions that will do the actual
command handling. Those functions are not yet implemented.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20200214132745.23392-3-eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patchs adds the skeleton for the virtio-iommu device.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20200214132745.23392-2-eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The virtqueue code sets up MemoryRegionCaches to access the virtqueue
guest RAM data structures. The code currently assumes that
VRingMemoryRegionCaches is initialized before device emulation code
accesses the virtqueue. An assertion will fail in
vring_get_region_caches() when this is not true. Device fuzzing found a
case where this assumption is false (see below).
Virtqueue guest RAM addresses can also be changed from a vCPU thread
while an IOThread is accessing the virtqueue. This breaks the same
assumption but this time the caches could become invalid partway through
the virtqueue code. The code fetches the caches RCU pointer multiple
times so we will need to validate the pointer every time it is fetched.
Add checks each time we call vring_get_region_caches() and treat invalid
caches as a nop: memory stores are ignored and memory reads return 0.
The fuzz test failure is as follows:
$ qemu -M pc -device virtio-blk-pci,id=drv0,drive=drive0,addr=4.0 \
-drive if=none,id=drive0,file=null-co://,format=raw,auto-read-only=off \
-drive if=none,id=drive1,file=null-co://,file.read-zeroes=on,format=raw \
-display none \
-qtest stdio
endianness
outl 0xcf8 0x80002020
outl 0xcfc 0xe0000000
outl 0xcf8 0x80002004
outw 0xcfc 0x7
write 0xe0000000 0x24 0x00ffffffabffffffabffffffabffffffabffffffabffffffabffffffabffffffabffffffabffffffabffffffabffffffabffffffabffffffab5cffffffabffffffabffffffabffffffabffffffabffffffabffffffabffffffabffffffabffffffabffffffabffffffabffffffabffffffabffffffab0000000001
inb 0x4
writew 0xe000001c 0x1
write 0xe0000014 0x1 0x0d
The following error message is produced:
qemu-system-x86_64: /home/stefanha/qemu/hw/virtio/virtio.c:286: vring_get_region_caches: Assertion `caches != NULL' failed.
The backtrace looks like this:
#0 0x00007ffff5520625 in raise () at /lib64/libc.so.6
#1 0x00007ffff55098d9 in abort () at /lib64/libc.so.6
#2 0x00007ffff55097a9 in _nl_load_domain.cold () at /lib64/libc.so.6
#3 0x00007ffff5518a66 in annobin_assert.c_end () at /lib64/libc.so.6
#4 0x00005555559073da in vring_get_region_caches (vq=<optimized out>) at qemu/hw/virtio/virtio.c:286
#5 vring_get_region_caches (vq=<optimized out>) at qemu/hw/virtio/virtio.c:283
#6 0x000055555590818d in vring_used_flags_set_bit (mask=1, vq=0x5555575ceea0) at qemu/hw/virtio/virtio.c:398
#7 virtio_queue_split_set_notification (enable=0, vq=0x5555575ceea0) at qemu/hw/virtio/virtio.c:398
#8 virtio_queue_set_notification (vq=vq@entry=0x5555575ceea0, enable=enable@entry=0) at qemu/hw/virtio/virtio.c:451
#9 0x0000555555908512 in virtio_queue_set_notification (vq=vq@entry=0x5555575ceea0, enable=enable@entry=0) at qemu/hw/virtio/virtio.c:444
#10 0x00005555558c697a in virtio_blk_handle_vq (s=0x5555575c57e0, vq=0x5555575ceea0) at qemu/hw/block/virtio-blk.c:775
#11 0x0000555555907836 in virtio_queue_notify_aio_vq (vq=0x5555575ceea0) at qemu/hw/virtio/virtio.c:2244
#12 0x0000555555cb5dd7 in aio_dispatch_handlers (ctx=ctx@entry=0x55555671a420) at util/aio-posix.c:429
#13 0x0000555555cb67a8 in aio_dispatch (ctx=0x55555671a420) at util/aio-posix.c:460
#14 0x0000555555cb307e in aio_ctx_dispatch (source=<optimized out>, callback=<optimized out>, user_data=<optimized out>) at util/async.c:260
#15 0x00007ffff7bbc510 in g_main_context_dispatch () at /lib64/libglib-2.0.so.0
#16 0x0000555555cb5848 in glib_pollfds_poll () at util/main-loop.c:219
#17 os_host_main_loop_wait (timeout=<optimized out>) at util/main-loop.c:242
#18 main_loop_wait (nonblocking=<optimized out>) at util/main-loop.c:518
#19 0x00005555559b20c9 in main_loop () at vl.c:1683
#20 0x0000555555838115 in main (argc=<optimized out>, argv=<optimized out>, envp=<optimized out>) at vl.c:4441
Reported-by: Alexander Bulekov <alxndr@bu.edu>
Cc: Michael Tsirkin <mst@redhat.com>
Cc: Cornelia Huck <cohuck@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: qemu-stable@nongnu.org
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20200207104619.164892-1-stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
use the new virtio_delete_queue function to cleanup.
Signed-off-by: Pan Nengyuan <pannengyuan@huawei.com>
Message-Id: <20200224041336.30790-3-pannengyuan@huawei.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
virtio queues forgot to delete in unrealize, and aslo error path in
realize, this patch fix these memleaks, the leak stack is as follow:
Direct leak of 114688 byte(s) in 16 object(s) allocated from:
#0 0x7f24024fdbf0 in calloc (/lib64/libasan.so.3+0xcabf0)
#1 0x7f2401642015 in g_malloc0 (/lib64/libglib-2.0.so.0+0x50015)
#2 0x55ad175a6447 in virtio_add_queue /mnt/sdb/qemu/hw/virtio/virtio.c:2327
#3 0x55ad17570cf9 in vhost_user_blk_device_realize /mnt/sdb/qemu/hw/block/vhost-user-blk.c:419
#4 0x55ad175a3707 in virtio_device_realize /mnt/sdb/qemu/hw/virtio/virtio.c:3509
#5 0x55ad176ad0d1 in device_set_realized /mnt/sdb/qemu/hw/core/qdev.c:876
#6 0x55ad1781ff9d in property_set_bool /mnt/sdb/qemu/qom/object.c:2080
#7 0x55ad178245ae in object_property_set_qobject /mnt/sdb/qemu/qom/qom-qobject.c:26
#8 0x55ad17821eb4 in object_property_set_bool /mnt/sdb/qemu/qom/object.c:1338
#9 0x55ad177aeed7 in virtio_pci_realize /mnt/sdb/qemu/hw/virtio/virtio-pci.c:1801
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Pan Nengyuan <pannengyuan@huawei.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20200224041336.30790-2-pannengyuan@huawei.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Similar to other virtio-deivces, ctrl_vq forgot to delete in virtio_crypto_device_unrealize, this patch fix it.
This device has aleardy maintained vq pointers. Thus, we use the new virtio_delete_queue function directly to do the cleanup.
The leak stack:
Direct leak of 10752 byte(s) in 3 object(s) allocated from:
#0 0x7f4c024b1970 in __interceptor_calloc (/lib64/libasan.so.5+0xef970)
#1 0x7f4c018be49d in g_malloc0 (/lib64/libglib-2.0.so.0+0x5249d)
#2 0x55a2f8017279 in virtio_add_queue /mnt/sdb/qemu-new/qemu_test/qemu/hw/virtio/virtio.c:2333
#3 0x55a2f8057035 in virtio_crypto_device_realize /mnt/sdb/qemu-new/qemu_test/qemu/hw/virtio/virtio-crypto.c:814
#4 0x55a2f8005d80 in virtio_device_realize /mnt/sdb/qemu-new/qemu_test/qemu/hw/virtio/virtio.c:3531
#5 0x55a2f8497d1b in device_set_realized /mnt/sdb/qemu-new/qemu_test/qemu/hw/core/qdev.c:891
#6 0x55a2f8b48595 in property_set_bool /mnt/sdb/qemu-new/qemu_test/qemu/qom/object.c:2238
#7 0x55a2f8b54fad in object_property_set_qobject /mnt/sdb/qemu-new/qemu_test/qemu/qom/qom-qobject.c:26
#8 0x55a2f8b4de2c in object_property_set_bool /mnt/sdb/qemu-new/qemu_test/qemu/qom/object.c:1390
#9 0x55a2f80609c9 in virtio_crypto_pci_realize /mnt/sdb/qemu-new/qemu_test/qemu/hw/virtio/virtio-crypto-pci.c:58
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Pan Nengyuan <pannengyuan@huawei.com>
Cc: "Gonglei (Arei)" <arei.gonglei@huawei.com>
Message-Id: <20200225075554.10835-5-pannengyuan@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Similar to other virtio-devices, rq_vq forgot to delete in
virtio_pmem_unrealize, this patch fix it. This device has already
maintained a vq pointer, thus we use the new virtio_delete_queue
function directly to do the cleanup.
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Pan Nengyuan <pannengyuan@huawei.com>
Message-Id: <20200225075554.10835-4-pannengyuan@huawei.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
use the new virtio_delete_queue function to cleanup.
Signed-off-by: Pan Nengyuan <pannengyuan@huawei.com>
Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20200225075554.10835-3-pannengyuan@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Similar to other virtio device(https://patchwork.kernel.org/patch/11399237/), virtio queues forgot to delete in unrealize, and aslo error path in realize, this patch fix these memleaks, the leak stack is as follow:
Direct leak of 57344 byte(s) in 1 object(s) allocated from:
#0 0x7f15784fb970 in __interceptor_calloc (/lib64/libasan.so.5+0xef970)
#1 0x7f157790849d in g_malloc0 (/lib64/libglib-2.0.so.0+0x5249d)
#2 0x55587a1bf859 in virtio_add_queue /mnt/sdb/qemu-new/qemu_test/qemu/hw/virtio/virtio.c:2333
#3 0x55587a2071d5 in vuf_device_realize /mnt/sdb/qemu-new/qemu_test/qemu/hw/virtio/vhost-user-fs.c:212
#4 0x55587a1ae360 in virtio_device_realize /mnt/sdb/qemu-new/qemu_test/qemu/hw/virtio/virtio.c:3531
#5 0x55587a63fb7b in device_set_realized /mnt/sdb/qemu-new/qemu_test/qemu/hw/core/qdev.c:891
#6 0x55587acf03f5 in property_set_bool /mnt/sdb/qemu-new/qemu_test/qemu/qom/object.c:2238
#7 0x55587acfce0d in object_property_set_qobject /mnt/sdb/qemu-new/qemu_test/qemu/qom/qom-qobject.c:26
#8 0x55587acf5c8c in object_property_set_bool /mnt/sdb/qemu-new/qemu_test/qemu/qom/object.c:1390
#9 0x55587a8e22a2 in pci_qdev_realize /mnt/sdb/qemu-new/qemu_test/qemu/hw/pci/pci.c:2095
#10 0x55587a63fb7b in device_set_realized /mnt/sdb/qemu-new/qemu_test/qemu/hw/core/qdev.c:891
#11 0x55587acf03f5 in property_set_bool /mnt/sdb/qemu-new/qemu_test/qemu/qom/object.c:2238
#12 0x55587acfce0d in object_property_set_qobject /mnt/sdb/qemu-new/qemu_test/qemu/qom/qom-qobject.c:26
#13 0x55587acf5c8c in object_property_set_bool /mnt/sdb/qemu-new/qemu_test/qemu/qom/object.c:1390
#14 0x55587a496d65 in qdev_device_add /mnt/sdb/qemu-new/qemu_test/qemu/qdev-monitor.c:679
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Pan Nengyuan <pannengyuan@huawei.com>
Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20200225075554.10835-2-pannengyuan@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
