Since at least the 2.05 architecture, the slbia instruction takes an
IH field in the opcode to provide some control on the effect of the
slbia on the ERATs (level-1 TLB).
We can safely ignore it as we always flush the whole qemu TLB but
we should allow the bits in the decode.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We had code to handle the L bit in the opcode but we didn't
allow it in the decode mask.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The PPC_64BX instruction flag is used for a couple of newer
instructions currently on POWER8 but our implementation for
them works for POWER7 too (and already does the proper checking
of what is permitted) with one exception: stq needs to check
the ISA version.
This fixes the latter and add the instructions to POWER7
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We only had them on POWER8, add them to POWER7 as well
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This ports the existing 64-bit mechanism to 32-bit, thus series
of 64 tlbie's followed by a sync like some versions of Darwin
(ab)use will result in a single flush.
We apply a pending flush on any sync instruction though, as Darwin
doesn't use tlbsync on non-SMP systems.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The processor only uses some bits of the address and invalidates an
entire congruence class. Some OSes such as Darwin and HelenOS take
advantage of this and occasionally invalidate the entire TLB by just
doing a series of 64 consecutive tlbie for example.
Our code tries to be too smart here only invalidating a segment
congruence class (ie, allowing more address bits to be relevant
in the invalidation), this fails miserably on those OSes.
Instead don't bother, do like ppc64 and blow the whole tlb when tlbie
is executed.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We used to always flush the TLB when changing relocation mode in
MSR:IR and MSR:DR (ie. MMU on/off for Instructions and Data).
We don't anymore since we have split mmu_idx for instruction and data.
However, since we hard code the mmu_idx in the translated code, we
now need to also make sure MSR:IR and MSR:DR are part of the hflags
used to tag translated code, so that we use different translated
code for different MMU settings.
Darwin gets hurt by this problem.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This fixes compilation of mmu_helper.c when all of the debug #defines at
the start of the file are enabled.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It's become redundant since it was added in commit 09aa9a5 "spapr-pci:
enable adding PHB via -device".
Cc: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
commit 74693da988 ('ppc: tlbie, tlbia and tlbisync are HV only')
introduced some extra checks on the instruction privilege. slbia was
changed wrongly and hrfid, tlbia were forgotten.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This helper is only used by the various instructions that can alter
MSR and not interrupts. Add a comment to that effect to the interrupt
code as well in case somebody wants to change this
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We use an env. flag which is set to the initial value of MSR_HVB in
the msr_mask. We also adjust the POWER8 mask to set SHV.
Also use this to adjust ctx.hv so that it is *set* when the processor
doesn't have an HV mode (970 with Apple mode for example), thus enabling
hypervisor instructions/SPRs.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
[clg: ctx.hv used to be defined only for the hypervisor kernel
(HV=1|PR=0). It is now defined also when PR=1 and conditions are
fixed accordingly.
stripped unwanted tabs.]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
KVM now supports 512 memslots on PowerPC (earlier it was 32). Allow half
of it (256) to be used as hotpluggable memory slots.
Instead of hard coding the max value, use the KVM supplied value if KVM
is enabled. Otherwise resort to the default value of 32.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This will be later used by the "ibm,reset-pe-dma-window" RTAS handler
which resets the DMA configuration to the defaults.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
LoPAPR dictates that during system reset all DMA windows must be removed
and the default DMA32 window must be created so does the patch.
At the moment there is just one window supported so no change in
behaviour is expected.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We are going to have multiple DMA windows at different offsets on
a PCI bus. For the sake of migration, we will have as many TCE table
objects pre-created as many windows supported.
So we need a way to map windows dynamically onto a PCI bus
when migration of a table is completed but at this stage a TCE table
object does not have access to a PHB to ask it to map a DMA window
backed by just migrated TCE table.
This adds a "root" memory region (UINT64_MAX long) to the TCE object.
This new region is mapped on a PCI bus with enabled overlapping as
there will be one root MR per TCE table, each of them mapped at 0.
The actual IOMMU memory region is a subregion of the root region and
a TCE table enables/disables this subregion and maps it at
the specific offset inside the root MR which is 1:1 mapping of
a PCI address space.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The source guest could have reallocated the default TCE table and
migrate bigger/smaller table. This adds reallocation in post_load()
if the default table size is different on source and destination.
This adds @bus_offset, @page_shift to the migration stream as
a subsection so when DDW is added, migration to older machines will
still be possible. As @bus_offset and @page_shift are not used yet,
this makes no change in behavior.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Currently TCE tables are created once at start and their sizes never
change. We are going to change that by introducing a Dynamic DMA windows
support where DMA configuration may change during the guest execution.
This changes spapr_tce_new_table() to create an empty zero-size IOMMU
memory region (IOMMU MR). Only LIOBN is assigned by the time of creation.
It still will be called once at the owner object (VIO or PHB) creation.
This introduces an "enabled" state for TCE table objects, some
helper functions are added:
- spapr_tce_table_enable() receives TCE table parameters, stores in
sPAPRTCETable and allocates a guest view of the TCE table
(in the user space or KVM) and sets the correct size on the IOMMU MR;
- spapr_tce_table_disable() disposes the table and resets the IOMMU MR
size; it is made public as the following DDW code will be using it.
This changes the PHB reset handler to do the default DMA initialization
instead of spapr_phb_realize(). This does not make differenct now but
later with more than just one DMA window, we will have to remove them all
and create the default one on a system reset.
No visible change in behaviour is expected except the actual table
will be reallocated every reset. We might optimize this later.
The other way to implement this would be dynamically create/remove
the TCE table QOM objects but this would make migration impossible
as the migration code expects all QOM objects to exist at the receiver
so we have to have TCE table objects created when migration begins.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This allows dynamic allocation for migrating arrays.
Already existing VMSTATE_VARRAY_UINT32 requires an array to be
pre-allocated, however there are cases when the size is not known in
advance and there is no real need to enforce it.
This defines another variant of VMSTATE_VARRAY_UINT32 with WMS_ALLOC
flag which tells the receiving side to allocate memory for the array
before receiving the data.
The first user of it is a dynamic DMA window which existence and size
are totally dynamic.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Introduce kvm_get_max_memslots() API that can be used to obtain the
maximum number of memslots supported by KVM.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
With specification at hand from the reference manual from Freescale
http://cache.nxp.com/files/32bit/doc/ref_manual/SPEPEM.pdf , I have found a fix
to efscmp* instructions handling in QEMU.
efscmp* instructions in QEMU set crD (Condition Register nibble) values as
(0b0100 << 2) = 0b10000 (consider the HELPER_SINGLE_SPE_CMP macro which left
shifts the value returned by efscmp* handler by 2 bits). A value of 0b10000 is
not correct according the to the reference manual.
The reference manual expects efscmp* instructions to return a value of 0bx1xx.
Please find attached a patch which disables left shifting in
HELPER_SINGLE_SPE_CMP macro. This macro is used by efscmp* and efstst*
instructions only. efstst* instruction handlers, in turn, call efscmp* handlers
too.
*Explanation:*
Traditionally, each crD (condition register nibble) consist of 4 bits, which is
set by comparisons as follows:
crD = W X Y Z
where
W = Less than
X = Greater than
Y = Equal to
However, efscmp* instructions being a special case return a binary result.
(efscmpeq will set the crD = 0bx1xx iff when op1 == op2 and 0bx0xx otherwise;
i.e. there is no notion of different crD values based on Less than, Greater
than and Equal to).
This effectively means that crD will store a "Greater than" comparison result
iff efscmp* instruction comparison is TRUE. Compiler exploits this feature by
checking for "Branch if Less than or Equal to" (ble instruction) OR "Branch if
Greater than" (bgt instruction) for Branch if FALSE OR Branch if TRUE
respectively after an efscmp* instruction. This can be seen in a assembly code
snippet below:
27 if (__real__ x != 3.0f || __imag__ x != 4.0f)
10000498: lwz r10,8(r31)
1000049c: lis r9,16448
100004a0: efscmpeq cr7,r10,r9
100004a4: ble- cr7,0x100004b8 <bar+60> //jump to abort() call
100004a8: lwz r10,12(r31)
100004ac: lis r9,16512
100004b0: efscmpeq cr7,r10,r9
100004b4: bgt- cr7,0x100004bc <bar+64> //skip abort() call
28 abort ();
100004b8: bl 0x10000808 <abort>
Signed-off-by: Talha Imran <talha_imran@mentor.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
* support instruction syndrome info for data aborts from A64 to EL2
* add HSTR_EL2 register
* fix incorrect ESR IL bits in various syndrome register cases
* virt: fix limit of 64-bit ACPI/ECAM PCI MMIO range
* gicv2: RAZ/WI non-sec access to sec interrupts
* i2c: add aspeed i2c controller
* virt: Reject gic-version=host for non-KVM (don't segv on aarch64 host)
* xlnx-zynqmp: Add a secure prop to en/disable ARM Security Extensions
* xlnx-zynqmp: Support KVM on AArch64 hosts
* ptimer: Various fixes for awkward corner cases
* char: QOMify various ARM UART models
* char: get rid of qemu_char_get_next_serial
* target-arm: Fix TTBR selecting logic on AArch32 Stage 2 translation
* zynqmp: Add the ZCU102 board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=mHQd
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20160606-1' into staging
target-arm queue:
* support instruction syndrome info for data aborts from A64 to EL2
* add HSTR_EL2 register
* fix incorrect ESR IL bits in various syndrome register cases
* virt: fix limit of 64-bit ACPI/ECAM PCI MMIO range
* gicv2: RAZ/WI non-sec access to sec interrupts
* i2c: add aspeed i2c controller
* virt: Reject gic-version=host for non-KVM (don't segv on aarch64 host)
* xlnx-zynqmp: Add a secure prop to en/disable ARM Security Extensions
* xlnx-zynqmp: Support KVM on AArch64 hosts
* ptimer: Various fixes for awkward corner cases
* char: QOMify various ARM UART models
* char: get rid of qemu_char_get_next_serial
* target-arm: Fix TTBR selecting logic on AArch32 Stage 2 translation
* zynqmp: Add the ZCU102 board
# gpg: Signature made Mon 06 Jun 2016 17:01:11 BST
# gpg: using RSA key 0x3C2525ED14360CDE
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>"
# gpg: aka "Peter Maydell <pmaydell@gmail.com>"
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>"
* remotes/pmaydell/tags/pull-target-arm-20160606-1: (25 commits)
zynqmp: Add the ZCU102 board
target-arm: Fix TTBR selecting logic on AArch32 Stage 2 translation
char: get rid of qemu_char_get_next_serial
hw/char: QOM'ify xilinx_uartlite model
hw/char: QOM'ify stm32f2xx_usart model
hw/char: QOM'ify digic-uart model
hw/char: QOM'ify cadence_uart model
hw/char: QOM'ify pl011 model
hw/ptimer: Introduce ptimer_get_limit
hw/ptimer: Support "on the fly" timer mode switch
hw/ptimer: Update .delta on period/freq change
hw/ptimer: Perform counter wrap around if timer already expired
hw/ptimer: Fix issues caused by the adjusted timer limit value
xlnx-zynqmp: Use the in kernel GIC model for KVM runs
xlnx-zynqmp: Delay realization of GIC until post CPU realization
xlnx-zynqmp: Make the RPU subsystem optional
xlnx-zynqmp: Add a secure prop to en/disable ARM Security Extensions
hw/arm/virt: Reject gic-version=host for non-KVM
i2c: add aspeed i2c controller
hw/intc/gic: RAZ/WI non-sec access to sec interrupts
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Most Zynq UltraScale+ users will be targetting and using the ZCU102
board instead of the development focused EP108. To make our QEMU machine
names clearer add a ZCU102 machine model.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: cc82eec026b2febfca252d73362bb7084616c1ad.1464213234.git.alistair.francis@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Address size is 40-bit for the AArch32 stage 2 translation,
and t0sz can be negative (from -8 to 7),
so we need to adjust it to use the existing TTBR selecting logic.
Signed-off-by: Sergey Sorokin <afarallax@yandex.ru>
Message-id: 1464974151-1231644-1-git-send-email-afarallax@yandex.ru
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
since there is no user of qemu_char_get_next_serial any more,
it's time to let it go away.
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Message-id: 1465028065-5855-7-git-send-email-zxq_yx_007@163.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* drop qemu_char_get_next_serial and use chardev prop
* create xilinx_uartlite_create wrapper function to create
xilinx_uartlite device
* change affected board code to use the new way
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Message-id: 1465028065-5855-6-git-send-email-zxq_yx_007@163.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* drop qemu_char_get_next_serial and use chardev prop
* change affected board code to use the new way
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Message-id: 1465028065-5855-5-git-send-email-zxq_yx_007@163.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* drop qemu_char_get_next_serial and use chardev prop
* change affected board code to use the new way
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Message-id: 1465028065-5855-4-git-send-email-zxq_yx_007@163.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* drop qemu_char_get_next_serial and use chardev prop
* create cadence_uart_create wrapper function to create
cadence_uart_device
* change affected board code to use the new way
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Message-id: 1465028065-5855-3-git-send-email-zxq_yx_007@163.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* drop qemu_char_get_next_serial and use chardev prop
* add pl011_create wrapper function to create pl011 uart device
* change affected board code to use the new way
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Message-id: 1465028065-5855-2-git-send-email-zxq_yx_007@163.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently ptimer users are used to store copy of the limit value, because
ptimer doesn't provide facility to retrieve the limit. Let's provide it.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: 8f1fa9f90d8dbf8086fb02f3b4835eaeb4089cf6.1464367869.git.digetx@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Allow switching between periodic <-> oneshot modes while timer is running.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: f030be6e28fbd219e1e8d22297aee367bd9af5bb.1464367869.git.digetx@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Delta value must be updated on period/freq change, otherwise running timer
would be restarted (counter reloaded with old delta). Only m68k/mcf520x
and arm/arm_timer devices are currently doing freq change correctly, i.e.
stopping the timer. Perform delta update to fix affected devices and
eliminate potential further mistakes.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: 4987ef5fdc128bb9a744fd794d3f609135c6a39c.1464367869.git.digetx@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
ptimer_get_count() might be called while QEMU timer already been expired.
In that case ptimer would return counter = 0, which might be undesirable
in case of polled timer. Do counter wrap around for periodic timer to keep
it distributed. In order to achieve more accurate emulation behaviour of
certain hardware, don't perform wrap around when in icount mode and return
counter = 0 in that case (that doesn't affect polled counter distribution).
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: 4ce381c7d24d85d165ff251d2875d16a4b6a5c04.1464367869.git.digetx@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Multiple issues here related to the timer with a adjusted .limit value:
1) ptimer_get_count() returns incorrect counter value for the disabled
timer after loading the counter with a small value, because adjusted limit
value is used instead of the original.
For instance:
1) ptimer_stop(t)
2) ptimer_set_period(t, 1)
3) ptimer_set_limit(t, 0, 1)
4) ptimer_get_count(t) <-- would return 10000 instead of 0
2) ptimer_get_count() might return incorrect value for the timer running
with a adjusted limit value.
For instance:
1) ptimer_stop(t)
2) ptimer_set_period(t, 1)
3) ptimer_set_limit(t, 10, 1)
4) ptimer_run(t)
5) ptimer_get_count(t) <-- might return value > 10
3) Neither ptimer_set_period() nor ptimer_set_freq() are adjusting the
limit value, so it is still possible to make timer timeout value
arbitrary small.
For instance:
1) ptimer_set_period(t, 10000)
2) ptimer_set_limit(t, 1, 0)
3) ptimer_set_period(t, 1) <-- bypass limit correction
Fix all of the above issues by adjusting timer period instead of the limit.
Perform the adjustment for periodic timer only. Use the delta value instead
of the limit to make decision whether adjustment is required, as limit could
be altered while timer is running, resulting in incorrect value returned by
ptimer_get_count.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: cd141f74f5737480ec586b9c7d18cce1d69884e2.1464367869.git.digetx@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use the in kernel GIC model when running with KVM enabled.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1464173555-12800-5-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Delay the realization of the GIC until after CPUs are
realized. This is needed for KVM as the in-kernel GIC
model will fail if it is realized with no available CPUs.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1464173555-12800-4-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The way we currently model the RPU subsystem is of quite
limited use. In addition to that, it causes problems for
KVM and for GDB debugging.
Make the RPU optional by adding a has_rpu property and
default to having it disabled.
This changes the default setup from having the RPU to not
longer having it.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1464173555-12800-3-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a secure prop to en/disable ARM Security Extensions.
This is particularly useful for KVM runs.
Default to disabled to match the behavior of KVM.
This changes the default setup from having the ARM Security
Extensions to not longer having them.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1464173555-12800-2-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Aspeed AST2400 integrates a set of 14 I2C/SMBus bus controllers
directly connected to the APB bus. They can be programmed as master or
slave but the propopsed model only supports the master mode.
On the TODO list, we also have :
- improve and harden the state machine.
- bus recovery support (used by the Linux driver).
- transfer mode state machine bits. this is not strictly necessary as
it is mostly used for debug. The bus busy bit is deducted from the
I2C core engine of qemu.
- support of the pool buffer: 2048 bytes of internal SRAM (not used
by the Linux driver).
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1464704307-25178-1-git-send-email-clg@kaod.org
[PMM: removed unused functions aspeed_i2c_bus_get_state() and
aspeed_i2c_bus_set_state()]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Treat non-secure accesses to registers and bits in registers of secure
interrupts as RAZ/WI.
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Message-id: 1464273945-2055-1-git-send-email-jens.wiklander@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Set the MMIO range limit field to 'base + size - 1' as required.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1463856217-17969-1-git-send-email-ard.biesheuvel@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Remove some incorrect code from arm_cpu_do_interrupt_aarch64()
which attempts to set the IL bit in the syndrome register based
on the value of env->thumb. This is wrong in several ways:
* IL doesn't indicate Thumb-vs-ARM, it indicates instruction
length (which may be 16 or 32 for Thumb and is always 32 for ARM)
* not every syndrome format uses IL like this -- for some IL is
always set, and for some it is always clear
* the code is changing esr_el[new_el] even for interrupt entry,
which is not supposed to modify ESR_ELx at all
Delete the code, and instead rely on the syndrome value in
env->exception.syndrome having already been set up with the
correct value of IL.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1463487258-27468-3-git-send-email-peter.maydell@linaro.org
For some exception syndrome types, the IL bit should always be set.
This includes the instruction abort, watchpoint and software step
syndrome types; add the missing ARM_EL_IL bit to the syndrome
values returned by syn_insn_abort(), syn_swstep() and syn_watchpoint().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1463487258-27468-2-git-send-email-peter.maydell@linaro.org
Add support for generating the ISS (Instruction Specific Syndrome) for
Data Abort exceptions taken from AArch64.
These syndromes are used by hypervisors for example to trap and emulate
memory accesses.
We save the decoded data out-of-band with the TBs at translation time.
When exceptions hit, the extra data attached to the TB is used to
recreate the state needed to encode instruction syndromes.
This avoids the need to emit moves with every load/store.
Based on a suggestion from Peter Maydell.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1462464601-10888-2-git-send-email-edgar.iglesias@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add the Hypervisor System Trap Register for EL2.
This register is used early in the Linux boot and without it the kernel
aborts with a "Synchronous Abort" error.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: ea5aae4b10283de4705b864fe9d4bd2eaddaacae.1463174342.git.alistair.francis@xilinx.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
