The masked interrupt status register should be the state of the interrupt
after masking.
There should be a logical AND instead of a logical OR between the
interrupt status and the interrupt mask.
Signed-off-by: Victor CLEMENT <victor.clement@openwide.fr>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 1433154824-6927-1-git-send-email-victor.clement@openwide.fr
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a GICv2m device to the virt board to enable MSIs on the generic PCI
host controller. We allocate 64 SPIs in the IRQ space for now (this can
be increased/decreased later) and map the GICv2m right after the GIC in
the memory map.
Reviewed-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Message-id: 1432897270-7780-5-git-send-email-christoffer.dall@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In preparation for adding the GICv2m which requires address specifiers
and is a subnode of the gic, we extend the gic DT definition to specify
the #address-cells and #size-cells properties and add an empty ranges
property properties of the DT node, since this is required to add the
v2m node as a child of the gic node.
Note that we must also expand the irq-map to reference the gic with the
right address-cells as a consequence of this change.
Reviewed-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Message-id: 1432897270-7780-4-git-send-email-christoffer.dall@linaro.org
Suggested-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The ARM GICv2m widget is a little device that handles MSI interrupt
writes to a trigger register and ties them to a range of interrupt lines
wires to the GIC. It has a few status/id registers and the interrupt wires,
and that's about it.
A board instantiates the device by setting the base SPI number and
number SPIs for the frame. The base-spi parameter is indexed in the SPI
number space only, so base-spi == 0, means IRQ number 32. When a device
(the PCI host controller) writes to the trigger register, the payload is
the GIC IRQ number, so we have to subtract 32 from that and then index
into our frame of SPIs.
When instantiating a GICv2m device, tell PCI that we have instantiated
something that can deal with MSIs. We rely on the board actually wiring
up the GICv2m to the PCI host controller.
Reviewed-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Message-id: 1432897270-7780-3-git-send-email-christoffer.dall@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Instead of passing the GIC phandle around between functions, add it to
the VirtBoardInfo just like we do for the clock_phandle. We are about
to add the v2m phandle as well, and it's easier not having to pass
around a bunch of phandles, return multiple values from functions, etc.
Reviewed-by: Eric Auger <eric.auger@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Message-id: 1432897270-7780-2-git-send-email-christoffer.dall@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Since we now require GLib 2.22+ (commit f40685c), we don't have to
work around lack of g_hash_table_get_keys() anymore.
This reverts commit 82a3a11897.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-id: 1432749090-4698-1-git-send-email-armbru@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1432881807-18164-11-git-send-email-edgar.iglesias@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1432881807-18164-10-git-send-email-edgar.iglesias@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1432881807-18164-9-git-send-email-edgar.iglesias@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1432881807-18164-8-git-send-email-edgar.iglesias@gmail.com
[PMM: Switch to preferred opc1/crm order for 64-bit AArch32 cpregs;
drop unneeded use of vmsa_ttbr_writefn]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1432881807-18164-7-git-send-email-edgar.iglesias@gmail.com
[PMM: reordered fields into preferred opc0/opc1/crn/crm/opc2 order]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1432881807-18164-6-git-send-email-edgar.iglesias@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1432881807-18164-5-git-send-email-edgar.iglesias@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1432881807-18164-4-git-send-email-edgar.iglesias@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Break down the overly broad wildcard definition of TLB_LOCKDOWN
down to v7 level.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1432881807-18164-3-git-send-email-edgar.iglesias@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This fixes a compile warning from clang 3.5 (the assertion
could never fire).
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1432881807-18164-2-git-send-email-edgar.iglesias@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: John Snow <jsnow@redhat.com>
[PMM: added note in commit message that this is fixing a build warning]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
My last pull breaks build on systems with iasl.
Fix this up.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVbLVUAAoJECgfDbjSjVRpk5gH/jW70lEDqSpqVZ2cmn4ki2jG
QTbuWELGm1qyuVBGU6RQ5V6L6WJbzLVy9hxgzs9bF7pQ3Q7N16aDBwwHeR5VVZuf
09htYH7V+5Lrx7rcCguoneOikSGgM5mGQrETDf8hp9ECyxj9jsEbCJUB2Wy7fIGA
KalnxP0sbdpUYyIbDRQUDNtU4MuhGKF0WzjNIUZ3H+L2JW2NBZMSrBQ5dSClPq6B
nVHSvjMtuAlkwCsH6F2FXFldxqMdgByZBzZ6H4ZMssGsIYKnbXhR/3vsdVdS4nef
YTzGtSRAPhDR3zKpV7+VsuOD+xPHDsparKlk8TDo2uKeJVB9Q0vBdv43vNyvnH8=
=Bqzz
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pc build fix
My last pull breaks build on systems with iasl.
Fix this up.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Mon Jun 1 20:41:08 2015 BST using RSA key ID D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
* remotes/mst/tags/for_upstream:
acpi: add missing ssdt
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
As the implementation of const_le16 and const_le32 is not build time constant
on big endian systems this need to be fixed.
CC hw/input/virtio-input-hid.o
hw/input/virtio-input-hid.c:340:13: error: initializer element is not constant
hw/input/virtio-input-hid.c:340:13: error: (near initialization for ‘virtio_keyboard_config[1].u.ids.bustype’)
...
Signed-off-by: Michael Mueller <mimu@linux.vnet.ibm.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
... and change return type to bool.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
While there, inline the pointless qmp_cmd_mode() wrapper.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
Superfluous since commit 30f5041 removed it from HMP.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
While there, rename its type as well, from MonitorControl to
MonitorQMP.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
The previous commits narrowed use of QError to handle_qmp_command()
and its helpers monitor_protocol_emitter(), build_qmp_error_dict().
Narrow it further to just the command handler call: instead of
converting Error to QError throughout handle_qmp_command(), convert
the QError gotten from the command handler to Error, and switch the
helpers from QError to Error.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
Move mon->error handling to its caller handle_qmp_command().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
All QMP commands use the "new" handler interface (mhandler.cmd_new).
Most HMP commands still use the traditional interface (mhandler.cmd),
but a few use the "new" one. Complicates handle_user_command() for no
gain, so I'm converting these to the traditional interface.
pcie_aer_inject_error's implementation is split into the
hmp_pcie_aer_inject_error() and pcie_aer_inject_error_print(). The
former is a peculiar crossbreed between HMP and QMP handler. On
success, it works like a QMP handler: store QDict through ret_data
parameter, return 0. Printing the QDict is left to
pcie_aer_inject_error_print(). On failure, it works more like an HMP
handler: print error to monitor, return negative number.
To convert to the traditional interface, turn
pcie_aer_inject_error_print() into a command handler wrapping around
hmp_pcie_aer_inject_error(). By convention, this command handler
should be called hmp_pcie_aer_inject_error(), so rename the existing
hmp_pcie_aer_inject_error() to do_pcie_aer_inject_error().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
All QMP commands use the "new" handler interface (mhandler.cmd_new).
Most HMP commands still use the traditional interface (mhandler.cmd),
but a few use the "new" one. Complicates handle_user_command() for no
gain, so I'm converting these to the traditional interface.
For device_add, that's easy: just wrap the obvious hmp_device_add()
around do_device_add().
monitor_user_noop() is now unused, drop it.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
All QMP commands use the "new" handler interface (mhandler.cmd_new).
Most HMP commands still use the traditional interface (mhandler.cmd),
but a few use the "new" one. Complicates handle_user_command() for no
gain, so I'm converting these to the traditional interface.
For drive_del, that's easy: hmp_drive_del() sheds its unused last
parameter, and its return value, which the caller ignored anyway.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
Protocol must be spice, vnc isn't implemented. Fix up documentation.
Attempts to use vnc or any other unknown protocol yield the misleading
error message "Invalid parameter 'protocol'". Improve it to
"Parameter 'protocol' expects spice".
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by. Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
Inline qmp_call_cmd() along with its helper handler_audit() into its
only caller handle_qmp_command(), and simplify the result.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
The asynchronous monitor command interface goes back to commit 940cc30
(Jan 2010). Added a third case to command execution. The hope back
then according to the commit message was that all commands get
converted to the asynchronous interface, killing off the other two
cases. Didn't happen.
The initial asynchronous commands balloon and info balloon were
converted back to synchronous long ago (commit 96637bc and d72f32),
with commit messages calling the asynchronous interface "not fully
working" and "deprecated". The only other user went away in commit
3b5704b.
New code generally uses synchronous commands and asynchronous events.
What exactly is still "not fully working" with asynchronous commands?
Well, here's a bug that defeats actual asynchronous use pretty
reliably: the reply's ID is wrong (and has always been wrong) unless
you use the command synchronously! To reproduce, we need an
asynchronous command, so we have to go back before commit 3b5704b.
Run QEMU with spice:
$ qemu-system-x86_64 -nodefaults -S -spice port=5900,disable-ticketing -qmp stdio
{"QMP": {"version": {"qemu": {"micro": 94, "minor": 2, "major": 2}, "package": ""}, "capabilities": []}}
Connect a spice client in another terminal:
$ remote-viewer spice://localhost:5900
Set up a migration destination dummy in a third terminal:
$ socat TCP-LISTEN:12345 STDIO
Now paste the following into the QMP monitor:
{ "execute": "qmp_capabilities", "id": "i0" }
{ "execute": "client_migrate_info", "id": "i1", "arguments": { "protocol": "spice", "hostname": "localhost", "port": 12345 } }
{ "execute": "query-kvm", "id": "i2" }
Produces two replies immediately, one to qmp_capabilities, and one to
query-kvm:
{"return": {}, "id": "i0"}
{"return": {"enabled": false, "present": true}, "id": "i2"}
Both are correct. Two lines of debug output from libspice-server not
shown.
Now EOF socat's standard input to make it close the connection. This
makes the asynchronous client_migrate_info complete. It replies:
{"return": {}}
Bug: "id": "i1" is missing. Two lines of debug output from
libspice-server not shown. Cherry on top: storage for the missing ID
is leaked.
Get rid of this stuff before somebody hurts himself with it.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
commit 5cb18b3d7b
TPM2 ACPI table support
was missing a file, so build with iasl fails
(build without iasl works since it uses the generated
hex files).
Reported-by: "Daniel P. Berrange" <berrange@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
A bunch of cleanups and fixes all over the place,
enhancements in TPM, virtio and vhost.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVbE3kAAoJECgfDbjSjVRphV4H/jEnq16oMP72H6xgbAIKjvrP
uEx4jgkj9qGfgqLQJURPKemgzNbP+dXjd4LkIdgbUvlknCgFeKyJVPxzCCIhjc7R
5D70Aptg1CdVNaMeqsIOyJIYe0hIXQjbF7a/jtxf8nR9+kLIOpcQ200oRJtxpGVu
VfzWnBj48PRXi/W03OinWYrkqeAqx0BNHRxXQ5Ylr/DxTBoJKmmp13wW/5U+Xtmi
g5hDS5IF/qqrIKftisR7sDEfXENJf3ZulqP/2N8Lvufyj1lQxGkEGTKD5FDzeaj6
X0/UvUv7I2OzCbcTyeCwzF1GfZOgGceiXxopEp359SkvyoJILF7/C0Na5LY/fiw=
=fckd
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pc, pci, tpm, virtio, vhost enhancements and fixes
A bunch of cleanups and fixes all over the place,
enhancements in TPM, virtio and vhost.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Mon Jun 1 13:19:48 2015 BST using RSA key ID D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
* remotes/mst/tags/for_upstream: (60 commits)
vhost-user: add multi queue support
virtio: make features 64bit wide
qdev: add 64bit properties
virtio-mmio: ioeventfd support
hw/acpi/aml-build: Fix memory leak
acpi: add aml_while() term
acpi: add aml_increment() term
acpi: add aml_shiftright() term
acpi: add aml_shiftleft() term
acpi: add aml_index() term
acpi: add aml_lless() term
acpi: add aml_add() term
TPM2 ACPI table support
tpm: Probe for connected TPM 1.2 or TPM 2
Extend TPM TIS interface to support TPM 2
Add stream ID to MSI write
acpi: Simplify printing to dynamic string
i386: drop FDC in pc-q35-2.4+ if neither it nor floppy drives are wanted
i386/pc_q35: don't insist on board FDC if there's no default floppy
i386/pc: '-drive if=floppy' should imply a board-default FDC
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Based on patch by Nikolay Nikolaev:
Vhost-user will implement the multi queue support in a similar way
to what vhost already has - a separate thread for each queue.
To enable the multi queue functionality - a new command line parameter
"queues" is introduced for the vhost-user netdev.
Signed-off-by: Nikolay Nikolaev <n.nikolaev@virtualopensystems.com>
Signed-off-by: Changchun Ouyang <changchun.ouyang@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Make features 64bit wide everywhere.
On migration a full 64bit guest_features field is sent if one of the
high bits is set, in addition to the lower 32bit guest_features field
which must stay for compatibility reasons. That way we send the lower
32 feature bits twice, but the code is simpler because we don't have
to split and compose the 64bit features into two 32bit fields.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Needed for virtio features which go from 32bit to 64bit with virtio 1.0
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
set_host_notifier and set_guest_notifiers supported by virtio-mmio now.
Most code copied from virtio-pci.
This makes it possible to use vhost-net with virtio-mmio,
improving performance by about 30%.
The kvm-arm does not yet support irqfd, need to fix the hard-coded part after
kvm-arm gets irqfd support.
Signed-off-by: Ying-Shiuan Pan <yingshiuan.pan@gmail.com>
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Shannon Zhao <zhaoshenglong@huawei.com>
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Add encoding for ACPI DefWhile Opcode.
Reviewed-by: Shannon Zhao <zhaoshenglong@huawei.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add encoding for ACPI DefIncrement Opcode.
Reviewed-by: Shannon Zhao <zhaoshenglong@huawei.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Victor CLEMENT
Christoffer Dall
Markus Armbruster
Edgar E. Iglesias
Peter Maydell
Gerd Hoffmann
Michael Mueller
Michael S. Tsirkin
Ouyang Changchun
Ying-Shiuan Pan
Shannon Zhao
Marcel Apfelbaum