Simply moving the non-stub helper_v7m_mrs/msr outside of
!CONFIG_USER_ONLY is not an option, because of all of the
other system-mode helpers that are called.
But we can split out a few subroutines to handle the few
EL0 accessible registers without duplicating code.
Reported-by: Christophe Lyon <christophe.lyon@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191118194916.3670-1-richard.henderson@linaro.org
[PMM: deleted now-redundant comment; added a default case
to switch in v7m_msr helper]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Armv8-A removes UNPREDICTABLE for R13 for these cases.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191117090621.32425-3-richard.henderson@linaro.org
[PMM: changed ENABLE_ARCH_8 checks to check a new bool 'v8a',
since these cases are still UNPREDICTABLE for v8M]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There was too much cut and paste between ldrexd and strexd,
as ldrexd does prohibit two output registers the same.
Fixes: af28822899
Reported-by: Michael Goffioul <michael.goffioul@gmail.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191117090621.32425-2-richard.henderson@linaro.org
Reviewed-by: Robert Foley <robert.foley@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Coverity reports, in sve_zcr_get_valid_len,
"Subtract operation overflows on operands
arm_cpu_vq_map_next_smaller(cpu, start_vq + 1U) and 1U"
First, the aarch32 stub version of arm_cpu_vq_map_next_smaller,
returning 0, does exactly what Coverity reports. Remove it.
Second, the aarch64 version of arm_cpu_vq_map_next_smaller has
a set of asserts, but they don't cover the case in question.
Further, there is a fair amount of extra arithmetic needed to
convert from the 0-based zcr register, to the 1-base vq form,
to the 0-based bitmap, and back again. This can be simplified
by leaving the value in the 0-based form.
Finally, use test_bit to simplify the common case, where the
length in the zcr registers is in fact a supported length.
Reported-by: Coverity (CID 1407217)
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 20191118091414.19440-1-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
rt==15 is a special case when reading the flags: it means the
destination is APSR. This patch avoids rejecting
vmrs apsr_nzcv, fpscr
as illegal instruction.
Cc: qemu-stable@nongnu.org
Signed-off-by: Christophe Lyon <christophe.lyon@linaro.org>
Message-id: 20191025095711.10853-1-christophe.lyon@linaro.org
[PMM: updated the comment]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Allow cpu 'host' to enable SVE when it's available, unless the
user chooses to disable it with the added 'sve=off' cpu property.
Also give the user the ability to select vector lengths with the
sve<N> properties. We don't adopt 'max' cpu's other sve property,
sve-max-vq, because that property is difficult to use with KVM.
That property assumes all vector lengths in the range from 1 up
to and including the specified maximum length are supported, but
there may be optional lengths not supported by the host in that
range. With KVM one must be more specific when enabling vector
lengths.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Masayoshi Mizuma <m.mizuma@jp.fujitsu.com>
Message-id: 20191031142734.8590-10-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Extend the SVE vq map initialization and validation with KVM's
supported vector lengths when KVM is enabled. In order to determine
and select supported lengths we add two new KVM functions for getting
and setting the KVM_REG_ARM64_SVE_VLS pseudo-register.
This patch has been co-authored with Richard Henderson, who reworked
the target/arm/cpu64.c changes in order to push all the validation and
auto-enabling/disabling steps into the finalizer, resulting in a nice
LOC reduction.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Masayoshi Mizuma <m.mizuma@jp.fujitsu.com>
Message-id: 20191031142734.8590-9-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
kvm_arm_create_scratch_host_vcpu() takes a struct kvm_vcpu_init
parameter. Rather than just using it as an output parameter to
pass back the preferred target, use it also as an input parameter,
allowing a caller to pass a selected target if they wish and to
also pass cpu features. If the caller doesn't want to select a
target they can pass -1 for the target which indicates they want
to use the preferred target and have it passed back like before.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Masayoshi Mizuma <m.mizuma@jp.fujitsu.com>
Reviewed-by: Beata Michalska <beata.michalska@linaro.org>
Message-id: 20191031142734.8590-8-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Enable SVE in the KVM guest when the 'max' cpu type is configured
and KVM supports it. KVM SVE requires use of the new finalize
vcpu ioctl, so we add that now too. For starters SVE can only be
turned on or off, getting all vector lengths the host CPU supports
when on. We'll add the other SVE CPU properties in later patches.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Masayoshi Mizuma <m.mizuma@jp.fujitsu.com>
Reviewed-by: Beata Michalska <beata.michalska@linaro.org>
Message-id: 20191031142734.8590-7-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
These are the SVE equivalents to kvm_arch_get/put_fpsimd. Note, the
swabbing is different than it is for fpsmid because the vector format
is a little-endian stream of words.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Masayoshi Mizuma <m.mizuma@jp.fujitsu.com>
Message-id: 20191031142734.8590-6-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Introduce cpu properties to give fine control over SVE vector lengths.
We introduce a property for each valid length up to the current
maximum supported, which is 2048-bits. The properties are named, e.g.
sve128, sve256, sve384, sve512, ..., where the number is the number of
bits. See the updates to docs/arm-cpu-features.rst for a description
of the semantics and for example uses.
Note, as sve-max-vq is still present and we'd like to be able to
support qmp_query_cpu_model_expansion with guests launched with e.g.
-cpu max,sve-max-vq=8 on their command lines, then we do allow
sve-max-vq and sve<N> properties to be provided at the same time, but
this is not recommended, and is why sve-max-vq is not mentioned in the
document. If sve-max-vq is provided then it enables all lengths smaller
than and including the max and disables all lengths larger. It also has
the side-effect that no larger lengths may be enabled and that the max
itself cannot be disabled. Smaller non-power-of-two lengths may,
however, be disabled, e.g. -cpu max,sve-max-vq=4,sve384=off provides a
guest the vector lengths 128, 256, and 512 bits.
This patch has been co-authored with Richard Henderson, who reworked
the target/arm/cpu64.c changes in order to push all the validation and
auto-enabling/disabling steps into the finalizer, resulting in a nice
LOC reduction.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Masayoshi Mizuma <m.mizuma@jp.fujitsu.com>
Reviewed-by: Beata Michalska <beata.michalska@linaro.org>
Message-id: 20191031142734.8590-5-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Since 97a28b0eea ("target/arm: Allow VFP and Neon to be disabled via
a CPU property") we can disable the 'max' cpu model's VFP and neon
features, but there's no way to disable SVE. Add the 'sve=on|off'
property to give it that flexibility. We also rename
cpu_max_get/set_sve_vq to cpu_max_get/set_sve_max_vq in order for them
to follow the typical *_get/set_<property-name> pattern.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Masayoshi Mizuma <m.mizuma@jp.fujitsu.com>
Reviewed-by: Beata Michalska <beata.michalska@linaro.org>
Message-id: 20191031142734.8590-4-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add support for the query-cpu-model-expansion QMP command to Arm. We
do this selectively, only exposing CPU properties which represent
optional CPU features which the user may want to enable/disable.
Additionally we restrict the list of queryable cpu models to 'max',
'host', or the current type when KVM is in use. And, finally, we only
implement expansion type 'full', as Arm does not yet have a "base"
CPU type. More details and example queries are described in a new
document (docs/arm-cpu-features.rst).
Note, certainly more features may be added to the list of advertised
features, e.g. 'vfp' and 'neon'. The only requirement is that we can
detect invalid configurations and emit failures at QMP query time.
For 'vfp' and 'neon' this will require some refactoring to share a
validation function between the QMP query and the CPU realize
functions.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Beata Michalska <beata.michalska@linaro.org>
Message-id: 20191031142734.8590-2-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Now the arm_ld*_code functions are only used at translate time we can
just pass down to translator_ld functions.
Signed-off-by: Emilio G. Cota <cota@braap.org>
[AJB: convert from plugin_insn_append to translator_ld]
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
This is the payoff.
From perf record -g data of ubuntu 18 boot and shutdown:
BEFORE:
- 23.02% 2.82% qemu-system-aar [.] helper_lookup_tb_ptr
- 20.22% helper_lookup_tb_ptr
+ 10.05% tb_htable_lookup
- 9.13% cpu_get_tb_cpu_state
3.20% aa64_va_parameters_both
0.55% fp_exception_el
- 11.66% 4.74% qemu-system-aar [.] cpu_get_tb_cpu_state
- 6.96% cpu_get_tb_cpu_state
3.63% aa64_va_parameters_both
0.60% fp_exception_el
0.53% sve_exception_el
AFTER:
- 16.40% 3.40% qemu-system-aar [.] helper_lookup_tb_ptr
- 13.03% helper_lookup_tb_ptr
+ 11.19% tb_htable_lookup
0.55% cpu_get_tb_cpu_state
0.98% 0.71% qemu-system-aar [.] cpu_get_tb_cpu_state
0.87% 0.24% qemu-system-aar [.] rebuild_hflags_a64
Before, helper_lookup_tb_ptr is the second hottest function in the
application, consuming almost a quarter of the runtime. Within the
entire execution, cpu_get_tb_cpu_state consumes about 12%.
After, helper_lookup_tb_ptr has dropped to the fourth hottest function,
with consumption dropping to a sixth of the runtime. Within the
entire execution, cpu_get_tb_cpu_state has dropped below 1%, and the
supporting function to rebuild hflags also consumes about 1%.
Assertions are retained for --enable-debug-tcg.
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191023150057.25731-25-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Continue setting, but not relying upon, env->hflags.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191023150057.25731-21-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Continue setting, but not relying upon, env->hflags.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191023150057.25731-20-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Continue setting, but not relying upon, env->hflags.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191023150057.25731-19-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Continue setting, but not relying upon, env->hflags.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191023150057.25731-18-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Begin setting, but not relying upon, env->hflags.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191023150057.25731-17-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This functions are given the mode and el state of the cpu
and writes the computed value to env->hflags.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191023150057.25731-16-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
By performing this store early, we avoid having to save and restore
the register holding the address around any function calls.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191023150057.25731-15-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This function assumes nothing about the current state of the cpu,
and writes the computed value to env->hflags.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191023150057.25731-13-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There are 3 conditions that each enable this flag. M-profile always
enables; A-profile with EL1 as AA64 always enables. Both of these
conditions can easily be cached. The final condition relies on the
FPEXC register which we are not prepared to cache.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191023150057.25731-12-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Hoist the variable load for PSTATE into the existing test vs is_a64.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191023150057.25731-11-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We do not need to compute any of these values for M-profile.
Further, XSCALE_CPAR overlaps VECSTRIDE so obviously the two
sets must be mutually exclusive.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191023150057.25731-10-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Create a function to compute the values of the TBFLAG_ANY bits
that will be cached, and are used by A-profile.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191023150057.25731-9-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently a trivial wrapper for rebuild_hflags_common_32.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191023150057.25731-8-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Hoist the computation of some TBFLAG_A32 bits that only apply to
M-profile under a single test for ARM_FEATURE_M.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191023150057.25731-7-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Create a function to compute the values of the TBFLAG_A32 bits
that will be cached, and are used by M-profile.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191023150057.25731-6-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Set TBFLAG_ANY.BE_DATA in rebuild_hflags_common_32 and
rebuild_hflags_a64 instead of rebuild_hflags_common, where we do
not need to re-test is_a64() nor re-compute the various inputs.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191023150057.25731-5-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Create a function to compute the values of the TBFLAG_A32 bits
that will be cached, and are used by all profiles.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191023150057.25731-4-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Create a function to compute the values of the TBFLAG_A64 bits
that will be cached. For now, the env->hflags variable is not
used, and the results are fed back to cpu_get_tb_cpu_state.
Note that not all BTI related flags are cached, so we have to
test the BTI feature twice -- once for those bits moved out to
rebuild_hflags_a64 and once for those bits that remain in
cpu_get_tb_cpu_state.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191023150057.25731-3-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Create a function to compute the values of the TBFLAG_ANY bits
that will be cached. For now, the env->hflags variable is not
used, and the results are fed back to cpu_get_tb_cpu_state.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191023150057.25731-2-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The 32-bit product should be sign-extended, not zero-extended.
Fixes: ea96b37464
Reported-by: Laurent Desnogues <laurent.desnogues@gmail.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Laurent Desnogues <laurent.desnogues@gmail.com>
Message-id: 20190912183058.17947-1-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
SH_EXT_STDOUT_STDERR is a v2.0 semihosting extension: the guest
can open ":tt" with a file mode requesting append access in
order to open stderr, in addition to the existing "open for
read for stdin or write for stdout". Implement this and
report it via the :semihosting-features data.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20190916141544.17540-16-peter.maydell@linaro.org
SH_EXT_EXIT_EXTENDED is a v2.0 semihosting extension: it
indicates that the implementation supports the SYS_EXIT_EXTENDED
function. This function allows both A64 and A32/T32 guests to
exit with a specified exit status, unlike the older SYS_EXIT
function which only allowed this for A64 guests. Implement
this extension.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20190916141544.17540-15-peter.maydell@linaro.org
Version 2.0 of the semihosting specification added support for
allowing a guest to detect whether the implementation supported
particular features. This works by the guest opening a magic
file ":semihosting-features", which contains a fixed set of
data with some magic numbers followed by a sequence of bytes
with feature flags. The file is expected to behave sensibly
for the various semihosting calls which operate on files
(SYS_FLEN, SYS_SEEK, etc).
Implement this as another kind of guest FD using our function
table dispatch mechanism. Initially we report no extended
features, so we have just one feature flag byte which is zero.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20190916141544.17540-14-peter.maydell@linaro.org
Factor out the implementation of SYS_FLEN via the new
function tables.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190916141544.17540-13-peter.maydell@linaro.org
Factor out the implementation of SYS_SEEK via the new function
tables.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190916141544.17540-12-peter.maydell@linaro.org
Factor out the implementation of SYS_ISTTY via the new function
tables.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190916141544.17540-11-peter.maydell@linaro.org
Factor out the implementation of SYS_READ via the
new function tables.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190916141544.17540-10-peter.maydell@linaro.org
Factor out the implementation of SYS_WRITE via the
new function tables.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190916141544.17540-9-peter.maydell@linaro.org
Currently for the semihosting calls which take a file descriptor
(SYS_CLOSE, SYS_WRITE, SYS_READ, SYS_ISTTY, SYS_SEEK, SYS_FLEN)
we have effectively two implementations, one for real host files
and one for when we indirect via the gdbstub. We want to add a
third one to deal with the magic :semihosting-features file.
Instead of having a three-way if statement in each of these
cases, factor out the implementation of the calls to separate
functions which we dispatch to via function pointers selected
via the GuestFDType for the guest fd.
In this commit, we set up the framework for the dispatch,
and convert the SYS_CLOSE call to use it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190916141544.17540-8-peter.maydell@linaro.org
When we are routing semihosting operations through the gdbstub, the
work of sorting out the return value and setting errno if necessary
is done by callback functions which are invoked by the gdbstub code.
Clean up some ifdeffery in those functions by having them call
set_swi_errno() to set the semihosting errno.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190916141544.17540-7-peter.maydell@linaro.org
The semihosting code needs accuss to the linux-user only
TaskState pointer so it can set the semihosting errno per-thread
for linux-user mode. At the moment we do this by having some
ifdefs so that we define a 'ts' local in do_arm_semihosting()
which is either a real TaskState * or just a CPUARMState *,
depending on which mode we're compiling for.
This is awkward if we want to refactor do_arm_semihosting()
into other functions which might need to be passed the TaskState.
Restrict usage of the TaskState local by:
* making set_swi_errno() always take the CPUARMState pointer
and (for the linux-user version) get TaskState from that
* creating a new get_swi_errno() which reads the errno
* having the two semihosting calls which need the TaskState
for other purposes (SYS_GET_CMDLINE and SYS_HEAPINFO)
define a variable with scope restricted to just that code
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190916141544.17540-6-peter.maydell@linaro.org
Currently the Arm semihosting code returns the guest file descriptors
(handles) which are simply the fd values from the host OS or the
remote gdbstub. Part of the semihosting 2.0 specification requires
that we implement special handling of opening a ":semihosting-features"
filename. Guest fds which result from opening the special file
won't correspond to host fds, so to ensure that we don't end up
with duplicate fds we need to have QEMU code control the allocation
of the fd values we give the guest.
Add in an abstraction layer which lets us allocate new guest FD
values, and translate from a guest FD value back to the host one.
This also fixes an odd hole where a semihosting guest could
use the semihosting API to read, write or close file descriptors
that it had never allocated but which were being used by QEMU itself.
(This isn't a security hole, because enabling semihosting permits
the guest to do arbitrary file access to the whole host filesystem,
and so should only be done if the guest is completely trusted.)
Currently the only kind of guest fd is one which maps to a
host fd, but in a following commit we will add one which maps
to the :semihosting-features magic data.
If the guest is migrated with an open semihosting file descriptor
then subsequent attempts to use the fd will all fail; this is
not a change from the previous situation (where the host fd
being used on the source end would not be re-opened on the
destination end).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190916141544.17540-5-peter.maydell@linaro.org
In arm_gdb_syscall() we have a comment suggesting a race
because the syscall completion callback might not happen
before the gdb_do_syscallv() call returns. The comment is
correct that the callback may not happen but incorrect about
the effects. Correct it and note the important caveat that
callers must never do any work of any kind after return from
arm_gdb_syscall() that depends on its return value.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190916141544.17540-4-peter.maydell@linaro.org
If we fail a semihosting call we should always set the
semihosting errno to something; we were failing to do
this for some of the "check inputs for sanity" cases.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190916141544.17540-3-peter.maydell@linaro.org
