No header includes qemu-common.h after this commit, as prescribed by
qemu-common.h's file comment.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190523143508.25387-5-armbru@redhat.com>
[Rebased with conflicts resolved automatically, except for
include/hw/arm/xlnx-zynqmp.h hw/arm/nrf51_soc.c hw/arm/msf2-soc.c
block/qcow2-refcount.c block/qcow2-cluster.c block/qcow2-cache.c
target/arm/cpu.h target/lm32/cpu.h target/m68k/cpu.h target/mips/cpu.h
target/moxie/cpu.h target/nios2/cpu.h target/openrisc/cpu.h
target/riscv/cpu.h target/tilegx/cpu.h target/tricore/cpu.h
target/unicore32/cpu.h target/xtensa/cpu.h; bsd-user/main.c and
net/tap-bsd.c fixed up]
Perform a per-element conditional move. This combination operation is
easier to implement on some host vector units than plain cmp+bitsel.
Omit the usual gvec interface, as this is intended to be used by
target-specific gvec expansion call-backs.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This operation performs d = (b & a) | (c & ~a), and is present
on a majority of host vector units. Include gvec expanders.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Allow expansion either via shift by scalar or by replicating
the scalar for shift by vector.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
---
v3: Use a private structure for do_gvec_shifts.
The gvec expanders perform a modulo on the shift count. If the target
requires alternate behaviour, then it cannot use the generic gvec
expanders anyway, and will have to have its own custom code.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Allow the backend to expand dup from memory directly, instead of
forcing the value into a temp first. This is especially important
if integer/vector register moves do not exist.
Note that officially tcg_out_dupm_vec is allowed to fail.
If it did, we could fix this up relatively easily:
VECE == 32/64:
Load the value into a vector register, then dup.
Both of these must work.
VECE == 8/16:
If the value happens to be at an offset such that an aligned
load would place the desired value in the least significant
end of the register, go ahead and load w/garbage in high bits.
Load the value w/INDEX_op_ld{8,16}_i32.
Attempt a move directly to vector reg, which may fail.
Store the value into the backing store for OTS.
Load the value into the vector reg w/TCG_TYPE_I32, which must work.
Duplicate from the vector reg into itself, which must work.
All of which is well and good, except that all supported
hosts can support dupm for all vece, so all of the failure
paths would be dead code and untestable.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Replace the single opcode in .opc with a null-terminated
array in .opt_opc. We still require that all opcodes be
used with the same .vece.
Validate the contents of this list with CONFIG_DEBUG_TCG.
All tcg_gen_*_vec functions will check any list active
during .fniv expansion. Swap the active list in and out
as we expand other opcodes, or take control away from the
front-end function.
Convert all existing vector aware front ends.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
PowerPC Altivec does not support add and subtract of 64-bit elements.
Prepare for that configuration by not assuming the operation is
universally supported.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
It's either "GNU *Library* General Public version 2" or "GNU Lesser
General Public version *2.1*", but there was no "version 2.0" of the
"Lesser" library. So assume that version 2.1 is meant here.
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <1548252536-6242-5-git-send-email-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
In db432672, we allow wide inputs for operations such as add.
However, in 212be173 and 3774030a we didn't do the same for
compare and multiply.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Opcodes are added for scalar and vector shifts, but considering the
varied semantics of these do not expose them to the front ends. Do
go ahead and provide them in case they are needed for backend expansion.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
