473 lines
14 KiB
C
473 lines
14 KiB
C
/*
|
|
* Arm PrimeCell PL181 MultiMedia Card Interface
|
|
*
|
|
* Copyright (c) 2007 CodeSourcery.
|
|
* Written by Paul Brook
|
|
*
|
|
* This code is licenced under the GPL.
|
|
*/
|
|
|
|
#include "sysbus.h"
|
|
#include "sd.h"
|
|
#include "sysemu.h"
|
|
|
|
//#define DEBUG_PL181 1
|
|
|
|
#ifdef DEBUG_PL181
|
|
#define DPRINTF(fmt, ...) \
|
|
do { printf("pl181: " fmt , ## __VA_ARGS__); } while (0)
|
|
#else
|
|
#define DPRINTF(fmt, ...) do {} while(0)
|
|
#endif
|
|
|
|
#define PL181_FIFO_LEN 16
|
|
|
|
typedef struct {
|
|
SysBusDevice busdev;
|
|
SDState *card;
|
|
uint32_t clock;
|
|
uint32_t power;
|
|
uint32_t cmdarg;
|
|
uint32_t cmd;
|
|
uint32_t datatimer;
|
|
uint32_t datalength;
|
|
uint32_t respcmd;
|
|
uint32_t response[4];
|
|
uint32_t datactrl;
|
|
uint32_t datacnt;
|
|
uint32_t status;
|
|
uint32_t mask[2];
|
|
int fifo_pos;
|
|
int fifo_len;
|
|
/* The linux 2.6.21 driver is buggy, and misbehaves if new data arrives
|
|
while it is reading the FIFO. We hack around this be defering
|
|
subsequent transfers until after the driver polls the status word.
|
|
http://www.arm.linux.org.uk/developer/patches/viewpatch.php?id=4446/1
|
|
*/
|
|
int linux_hack;
|
|
uint32_t fifo[PL181_FIFO_LEN];
|
|
qemu_irq irq[2];
|
|
} pl181_state;
|
|
|
|
#define PL181_CMD_INDEX 0x3f
|
|
#define PL181_CMD_RESPONSE (1 << 6)
|
|
#define PL181_CMD_LONGRESP (1 << 7)
|
|
#define PL181_CMD_INTERRUPT (1 << 8)
|
|
#define PL181_CMD_PENDING (1 << 9)
|
|
#define PL181_CMD_ENABLE (1 << 10)
|
|
|
|
#define PL181_DATA_ENABLE (1 << 0)
|
|
#define PL181_DATA_DIRECTION (1 << 1)
|
|
#define PL181_DATA_MODE (1 << 2)
|
|
#define PL181_DATA_DMAENABLE (1 << 3)
|
|
|
|
#define PL181_STATUS_CMDCRCFAIL (1 << 0)
|
|
#define PL181_STATUS_DATACRCFAIL (1 << 1)
|
|
#define PL181_STATUS_CMDTIMEOUT (1 << 2)
|
|
#define PL181_STATUS_DATATIMEOUT (1 << 3)
|
|
#define PL181_STATUS_TXUNDERRUN (1 << 4)
|
|
#define PL181_STATUS_RXOVERRUN (1 << 5)
|
|
#define PL181_STATUS_CMDRESPEND (1 << 6)
|
|
#define PL181_STATUS_CMDSENT (1 << 7)
|
|
#define PL181_STATUS_DATAEND (1 << 8)
|
|
#define PL181_STATUS_DATABLOCKEND (1 << 10)
|
|
#define PL181_STATUS_CMDACTIVE (1 << 11)
|
|
#define PL181_STATUS_TXACTIVE (1 << 12)
|
|
#define PL181_STATUS_RXACTIVE (1 << 13)
|
|
#define PL181_STATUS_TXFIFOHALFEMPTY (1 << 14)
|
|
#define PL181_STATUS_RXFIFOHALFFULL (1 << 15)
|
|
#define PL181_STATUS_TXFIFOFULL (1 << 16)
|
|
#define PL181_STATUS_RXFIFOFULL (1 << 17)
|
|
#define PL181_STATUS_TXFIFOEMPTY (1 << 18)
|
|
#define PL181_STATUS_RXFIFOEMPTY (1 << 19)
|
|
#define PL181_STATUS_TXDATAAVLBL (1 << 20)
|
|
#define PL181_STATUS_RXDATAAVLBL (1 << 21)
|
|
|
|
#define PL181_STATUS_TX_FIFO (PL181_STATUS_TXACTIVE \
|
|
|PL181_STATUS_TXFIFOHALFEMPTY \
|
|
|PL181_STATUS_TXFIFOFULL \
|
|
|PL181_STATUS_TXFIFOEMPTY \
|
|
|PL181_STATUS_TXDATAAVLBL)
|
|
#define PL181_STATUS_RX_FIFO (PL181_STATUS_RXACTIVE \
|
|
|PL181_STATUS_RXFIFOHALFFULL \
|
|
|PL181_STATUS_RXFIFOFULL \
|
|
|PL181_STATUS_RXFIFOEMPTY \
|
|
|PL181_STATUS_RXDATAAVLBL)
|
|
|
|
static const unsigned char pl181_id[] =
|
|
{ 0x81, 0x11, 0x04, 0x00, 0x0d, 0xf0, 0x05, 0xb1 };
|
|
|
|
static void pl181_update(pl181_state *s)
|
|
{
|
|
int i;
|
|
for (i = 0; i < 2; i++) {
|
|
qemu_set_irq(s->irq[i], (s->status & s->mask[i]) != 0);
|
|
}
|
|
}
|
|
|
|
static void pl181_fifo_push(pl181_state *s, uint32_t value)
|
|
{
|
|
int n;
|
|
|
|
if (s->fifo_len == PL181_FIFO_LEN) {
|
|
fprintf(stderr, "pl181: FIFO overflow\n");
|
|
return;
|
|
}
|
|
n = (s->fifo_pos + s->fifo_len) & (PL181_FIFO_LEN - 1);
|
|
s->fifo_len++;
|
|
s->fifo[n] = value;
|
|
DPRINTF("FIFO push %08x\n", (int)value);
|
|
}
|
|
|
|
static uint32_t pl181_fifo_pop(pl181_state *s)
|
|
{
|
|
uint32_t value;
|
|
|
|
if (s->fifo_len == 0) {
|
|
fprintf(stderr, "pl181: FIFO underflow\n");
|
|
return 0;
|
|
}
|
|
value = s->fifo[s->fifo_pos];
|
|
s->fifo_len--;
|
|
s->fifo_pos = (s->fifo_pos + 1) & (PL181_FIFO_LEN - 1);
|
|
DPRINTF("FIFO pop %08x\n", (int)value);
|
|
return value;
|
|
}
|
|
|
|
static void pl181_send_command(pl181_state *s)
|
|
{
|
|
SDRequest request;
|
|
uint8_t response[16];
|
|
int rlen;
|
|
|
|
request.cmd = s->cmd & PL181_CMD_INDEX;
|
|
request.arg = s->cmdarg;
|
|
DPRINTF("Command %d %08x\n", request.cmd, request.arg);
|
|
rlen = sd_do_command(s->card, &request, response);
|
|
if (rlen < 0)
|
|
goto error;
|
|
if (s->cmd & PL181_CMD_RESPONSE) {
|
|
#define RWORD(n) ((response[n] << 24) | (response[n + 1] << 16) \
|
|
| (response[n + 2] << 8) | response[n + 3])
|
|
if (rlen == 0 || (rlen == 4 && (s->cmd & PL181_CMD_LONGRESP)))
|
|
goto error;
|
|
if (rlen != 4 && rlen != 16)
|
|
goto error;
|
|
s->response[0] = RWORD(0);
|
|
if (rlen == 4) {
|
|
s->response[1] = s->response[2] = s->response[3] = 0;
|
|
} else {
|
|
s->response[1] = RWORD(4);
|
|
s->response[2] = RWORD(8);
|
|
s->response[3] = RWORD(12) & ~1;
|
|
}
|
|
DPRINTF("Response received\n");
|
|
s->status |= PL181_STATUS_CMDRESPEND;
|
|
#undef RWORD
|
|
} else {
|
|
DPRINTF("Command sent\n");
|
|
s->status |= PL181_STATUS_CMDSENT;
|
|
}
|
|
return;
|
|
|
|
error:
|
|
DPRINTF("Timeout\n");
|
|
s->status |= PL181_STATUS_CMDTIMEOUT;
|
|
}
|
|
|
|
/* Transfer data between the card and the FIFO. This is complicated by
|
|
the FIFO holding 32-bit words and the card taking data in single byte
|
|
chunks. FIFO bytes are transferred in little-endian order. */
|
|
|
|
static void pl181_fifo_run(pl181_state *s)
|
|
{
|
|
uint32_t bits;
|
|
uint32_t value;
|
|
int n;
|
|
int limit;
|
|
int is_read;
|
|
|
|
is_read = (s->datactrl & PL181_DATA_DIRECTION) != 0;
|
|
if (s->datacnt != 0 && (!is_read || sd_data_ready(s->card))
|
|
&& !s->linux_hack) {
|
|
limit = is_read ? PL181_FIFO_LEN : 0;
|
|
n = 0;
|
|
value = 0;
|
|
while (s->datacnt && s->fifo_len != limit) {
|
|
if (is_read) {
|
|
value |= (uint32_t)sd_read_data(s->card) << (n * 8);
|
|
n++;
|
|
if (n == 4) {
|
|
pl181_fifo_push(s, value);
|
|
value = 0;
|
|
n = 0;
|
|
}
|
|
} else {
|
|
if (n == 0) {
|
|
value = pl181_fifo_pop(s);
|
|
n = 4;
|
|
}
|
|
sd_write_data(s->card, value & 0xff);
|
|
value >>= 8;
|
|
n--;
|
|
}
|
|
s->datacnt--;
|
|
}
|
|
if (n && is_read) {
|
|
pl181_fifo_push(s, value);
|
|
}
|
|
}
|
|
s->status &= ~(PL181_STATUS_RX_FIFO | PL181_STATUS_TX_FIFO);
|
|
if (s->datacnt == 0) {
|
|
s->status |= PL181_STATUS_DATAEND;
|
|
/* HACK: */
|
|
s->status |= PL181_STATUS_DATABLOCKEND;
|
|
DPRINTF("Transfer Complete\n");
|
|
}
|
|
if (s->datacnt == 0 && s->fifo_len == 0) {
|
|
s->datactrl &= ~PL181_DATA_ENABLE;
|
|
DPRINTF("Data engine idle\n");
|
|
} else {
|
|
/* Update FIFO bits. */
|
|
bits = PL181_STATUS_TXACTIVE | PL181_STATUS_RXACTIVE;
|
|
if (s->fifo_len == 0) {
|
|
bits |= PL181_STATUS_TXFIFOEMPTY;
|
|
bits |= PL181_STATUS_RXFIFOEMPTY;
|
|
} else {
|
|
bits |= PL181_STATUS_TXDATAAVLBL;
|
|
bits |= PL181_STATUS_RXDATAAVLBL;
|
|
}
|
|
if (s->fifo_len == 16) {
|
|
bits |= PL181_STATUS_TXFIFOFULL;
|
|
bits |= PL181_STATUS_RXFIFOFULL;
|
|
}
|
|
if (s->fifo_len <= 8) {
|
|
bits |= PL181_STATUS_TXFIFOHALFEMPTY;
|
|
}
|
|
if (s->fifo_len >= 8) {
|
|
bits |= PL181_STATUS_RXFIFOHALFFULL;
|
|
}
|
|
if (s->datactrl & PL181_DATA_DIRECTION) {
|
|
bits &= PL181_STATUS_RX_FIFO;
|
|
} else {
|
|
bits &= PL181_STATUS_TX_FIFO;
|
|
}
|
|
s->status |= bits;
|
|
}
|
|
}
|
|
|
|
static uint32_t pl181_read(void *opaque, target_phys_addr_t offset)
|
|
{
|
|
pl181_state *s = (pl181_state *)opaque;
|
|
uint32_t tmp;
|
|
|
|
if (offset >= 0xfe0 && offset < 0x1000) {
|
|
return pl181_id[(offset - 0xfe0) >> 2];
|
|
}
|
|
switch (offset) {
|
|
case 0x00: /* Power */
|
|
return s->power;
|
|
case 0x04: /* Clock */
|
|
return s->clock;
|
|
case 0x08: /* Argument */
|
|
return s->cmdarg;
|
|
case 0x0c: /* Command */
|
|
return s->cmd;
|
|
case 0x10: /* RespCmd */
|
|
return s->respcmd;
|
|
case 0x14: /* Response0 */
|
|
return s->response[0];
|
|
case 0x18: /* Response1 */
|
|
return s->response[1];
|
|
case 0x1c: /* Response2 */
|
|
return s->response[2];
|
|
case 0x20: /* Response3 */
|
|
return s->response[3];
|
|
case 0x24: /* DataTimer */
|
|
return s->datatimer;
|
|
case 0x28: /* DataLength */
|
|
return s->datalength;
|
|
case 0x2c: /* DataCtrl */
|
|
return s->datactrl;
|
|
case 0x30: /* DataCnt */
|
|
return s->datacnt;
|
|
case 0x34: /* Status */
|
|
tmp = s->status;
|
|
if (s->linux_hack) {
|
|
s->linux_hack = 0;
|
|
pl181_fifo_run(s);
|
|
pl181_update(s);
|
|
}
|
|
return tmp;
|
|
case 0x3c: /* Mask0 */
|
|
return s->mask[0];
|
|
case 0x40: /* Mask1 */
|
|
return s->mask[1];
|
|
case 0x48: /* FifoCnt */
|
|
/* The documentation is somewhat vague about exactly what FifoCnt
|
|
does. On real hardware it appears to be when decrememnted
|
|
when a word is transfered between the FIFO and the serial
|
|
data engine. DataCnt is decremented after each byte is
|
|
transfered between the serial engine and the card.
|
|
We don't emulate this level of detail, so both can be the same. */
|
|
tmp = (s->datacnt + 3) >> 2;
|
|
if (s->linux_hack) {
|
|
s->linux_hack = 0;
|
|
pl181_fifo_run(s);
|
|
pl181_update(s);
|
|
}
|
|
return tmp;
|
|
case 0x80: case 0x84: case 0x88: case 0x8c: /* FifoData */
|
|
case 0x90: case 0x94: case 0x98: case 0x9c:
|
|
case 0xa0: case 0xa4: case 0xa8: case 0xac:
|
|
case 0xb0: case 0xb4: case 0xb8: case 0xbc:
|
|
if (s->fifo_len == 0) {
|
|
fprintf(stderr, "pl181: Unexpected FIFO read\n");
|
|
return 0;
|
|
} else {
|
|
uint32_t value;
|
|
value = pl181_fifo_pop(s);
|
|
s->linux_hack = 1;
|
|
pl181_fifo_run(s);
|
|
pl181_update(s);
|
|
return value;
|
|
}
|
|
default:
|
|
hw_error("pl181_read: Bad offset %x\n", (int)offset);
|
|
return 0;
|
|
}
|
|
}
|
|
|
|
static void pl181_write(void *opaque, target_phys_addr_t offset,
|
|
uint32_t value)
|
|
{
|
|
pl181_state *s = (pl181_state *)opaque;
|
|
|
|
switch (offset) {
|
|
case 0x00: /* Power */
|
|
s->power = value & 0xff;
|
|
break;
|
|
case 0x04: /* Clock */
|
|
s->clock = value & 0xff;
|
|
break;
|
|
case 0x08: /* Argument */
|
|
s->cmdarg = value;
|
|
break;
|
|
case 0x0c: /* Command */
|
|
s->cmd = value;
|
|
if (s->cmd & PL181_CMD_ENABLE) {
|
|
if (s->cmd & PL181_CMD_INTERRUPT) {
|
|
fprintf(stderr, "pl181: Interrupt mode not implemented\n");
|
|
abort();
|
|
} if (s->cmd & PL181_CMD_PENDING) {
|
|
fprintf(stderr, "pl181: Pending commands not implemented\n");
|
|
abort();
|
|
} else {
|
|
pl181_send_command(s);
|
|
pl181_fifo_run(s);
|
|
}
|
|
/* The command has completed one way or the other. */
|
|
s->cmd &= ~PL181_CMD_ENABLE;
|
|
}
|
|
break;
|
|
case 0x24: /* DataTimer */
|
|
s->datatimer = value;
|
|
break;
|
|
case 0x28: /* DataLength */
|
|
s->datalength = value & 0xffff;
|
|
break;
|
|
case 0x2c: /* DataCtrl */
|
|
s->datactrl = value & 0xff;
|
|
if (value & PL181_DATA_ENABLE) {
|
|
s->datacnt = s->datalength;
|
|
pl181_fifo_run(s);
|
|
}
|
|
break;
|
|
case 0x38: /* Clear */
|
|
s->status &= ~(value & 0x7ff);
|
|
break;
|
|
case 0x3c: /* Mask0 */
|
|
s->mask[0] = value;
|
|
break;
|
|
case 0x40: /* Mask1 */
|
|
s->mask[1] = value;
|
|
break;
|
|
case 0x80: case 0x84: case 0x88: case 0x8c: /* FifoData */
|
|
case 0x90: case 0x94: case 0x98: case 0x9c:
|
|
case 0xa0: case 0xa4: case 0xa8: case 0xac:
|
|
case 0xb0: case 0xb4: case 0xb8: case 0xbc:
|
|
if (s->datacnt == 0) {
|
|
fprintf(stderr, "pl181: Unexpected FIFO write\n");
|
|
} else {
|
|
pl181_fifo_push(s, value);
|
|
pl181_fifo_run(s);
|
|
}
|
|
break;
|
|
default:
|
|
hw_error("pl181_write: Bad offset %x\n", (int)offset);
|
|
}
|
|
pl181_update(s);
|
|
}
|
|
|
|
static CPUReadMemoryFunc * const pl181_readfn[] = {
|
|
pl181_read,
|
|
pl181_read,
|
|
pl181_read
|
|
};
|
|
|
|
static CPUWriteMemoryFunc * const pl181_writefn[] = {
|
|
pl181_write,
|
|
pl181_write,
|
|
pl181_write
|
|
};
|
|
|
|
static void pl181_reset(void *opaque)
|
|
{
|
|
pl181_state *s = (pl181_state *)opaque;
|
|
|
|
s->power = 0;
|
|
s->cmdarg = 0;
|
|
s->cmd = 0;
|
|
s->datatimer = 0;
|
|
s->datalength = 0;
|
|
s->respcmd = 0;
|
|
s->response[0] = 0;
|
|
s->response[1] = 0;
|
|
s->response[2] = 0;
|
|
s->response[3] = 0;
|
|
s->datatimer = 0;
|
|
s->datalength = 0;
|
|
s->datactrl = 0;
|
|
s->datacnt = 0;
|
|
s->status = 0;
|
|
s->linux_hack = 0;
|
|
s->mask[0] = 0;
|
|
s->mask[1] = 0;
|
|
}
|
|
|
|
static int pl181_init(SysBusDevice *dev)
|
|
{
|
|
int iomemtype;
|
|
pl181_state *s = FROM_SYSBUS(pl181_state, dev);
|
|
BlockDriverState *bd;
|
|
|
|
iomemtype = cpu_register_io_memory(pl181_readfn,
|
|
pl181_writefn, s);
|
|
sysbus_init_mmio(dev, 0x1000, iomemtype);
|
|
sysbus_init_irq(dev, &s->irq[0]);
|
|
sysbus_init_irq(dev, &s->irq[1]);
|
|
bd = qdev_init_bdrv(&dev->qdev, IF_SD);
|
|
s->card = sd_init(bd, 0);
|
|
qemu_register_reset(pl181_reset, s);
|
|
pl181_reset(s);
|
|
/* ??? Save/restore. */
|
|
return 0;
|
|
}
|
|
|
|
static void pl181_register_devices(void)
|
|
{
|
|
sysbus_register_dev("pl181", sizeof(pl181_state), pl181_init);
|
|
}
|
|
|
|
device_init(pl181_register_devices)
|