qemu-e2k/tcg/tci
Richard Henderson 0df0a66555 tcg/tci: Remove CONFIG_DEBUG_TCG_INTERPRETER
There is nothing in this environment variable that cannot
be done better with -d flags.  There is nothing special
about TCI that warrants this hack.

Moreover, it does not compile -- remove it.

Reported-by: Song Gao <gaosong@loongson.cn>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
2022-07-05 16:17:53 +05:30
..
README tcg/tci: Change encoding to uint32_t units 2021-06-19 11:07:56 -07:00
tcg-target-con-set.h tcg/tci: Implement goto_ptr 2021-06-19 11:08:00 -07:00
tcg-target-con-str.h tcg/tci: Split out target constraints to tcg-target-con-str.h 2021-02-02 12:12:31 -10:00
tcg-target.c.inc tcg/tci: Remove CONFIG_DEBUG_TCG_INTERPRETER 2022-07-05 16:17:53 +05:30
tcg-target.h tcg/tci: Remove CONFIG_DEBUG_TCG_INTERPRETER 2022-07-05 16:17:53 +05:30

README

TCG Interpreter (TCI) - Copyright (c) 2011 Stefan Weil.

This file is released under the BSD license.

1) Introduction

TCG (Tiny Code Generator) is a code generator which translates
code fragments ("basic blocks") from target code (any of the
targets supported by QEMU) to a code representation which
can be run on a host.

QEMU can create native code for some hosts (arm, i386, ia64, ppc, ppc64,
s390, sparc, x86_64). For others, unofficial host support was written.

By adding a code generator for a virtual machine and using an
interpreter for the generated bytecode, it is possible to
support (almost) any host.

This is what TCI (Tiny Code Interpreter) does.

2) Implementation

Like each TCG host frontend, TCI implements the code generator in
tcg-target.c.inc, tcg-target.h. Both files are in directory tcg/tci.

The additional file tcg/tci.c adds the interpreter and disassembler.

The bytecode consists of opcodes (with only a few exceptions, with
the same same numeric values and semantics as used by TCG), and up
to six arguments packed into a 32-bit integer.  See comments in tci.c
for details on the encoding.

3) Usage

For hosts without native TCG, the interpreter TCI must be enabled by

        configure --enable-tcg-interpreter

If configure is called without --enable-tcg-interpreter, it will
suggest using this option. Setting it automatically would need
additional code in configure which must be fixed when new native TCG
implementations are added.

For hosts with native TCG, the interpreter TCI can be enabled by

        configure --enable-tcg-interpreter

The only difference from running QEMU with TCI to running without TCI
should be speed. Especially during development of TCI, it was very
useful to compare runs with and without TCI. Create /tmp/qemu.log by

        qemu-system-i386 -d in_asm,op_opt,cpu -D /tmp/qemu.log -singlestep

once with interpreter and once without interpreter and compare the resulting
qemu.log files. This is also useful to see the effects of additional
registers or additional opcodes (it is easy to modify the virtual machine).
It can also be used to verify native TCGs.

Hosts with native TCG can also enable TCI by claiming to be unsupported:

        configure --cpu=unknown --enable-tcg-interpreter

configure then no longer uses the native linker script (*.ld) for
user mode emulation.


4) Status

TCI needs special implementation for 32 and 64 bit host, 32 and 64 bit target,
host and target with same or different endianness.

            | host (le)                     host (be)
            | 32             64             32             64
------------+------------------------------------------------------------
target (le) | s0, u0         s1, u1         s?, u?         s?, u?
32 bit      |
            |
target (le) | sc, uc         s1, u1         s?, u?         s?, u?
64 bit      |
            |
target (be) | sc, u0         sc, uc         s?, u?         s?, u?
32 bit      |
            |
target (be) | sc, uc         sc, uc         s?, u?         s?, u?
64 bit      |
            |

System emulation
s? = untested
sc = compiles
s0 = bios works
s1 = grub works
s2 = Linux boots

Linux user mode emulation
u? = untested
uc = compiles
u0 = static hello works
u1 = linux-user-test works

5) Todo list

* TCI is not widely tested. It was written and tested on a x86_64 host
  running i386 and x86_64 system emulation and Linux user mode.
  A cross compiled QEMU for i386 host also works with the same basic tests.
  A cross compiled QEMU for mipsel host works, too. It is terribly slow
  because I run it in a mips malta emulation, so it is an interpreted
  emulation in an emulation.
  A cross compiled QEMU for arm host works (tested with pc bios).
  A cross compiled QEMU for ppc host works at least partially:
  i386-linux-user/qemu-i386 can run a simple hello-world program
  (tested in a ppc emulation).

* Some TCG opcodes are either missing in the code generator and/or
  in the interpreter. These opcodes raise a runtime exception, so it is
  possible to see where code must be added.

* It might be useful to have a runtime option which selects the native TCG
  or TCI, so QEMU would have to include two TCGs. Today, selecting TCI
  is a configure option, so you need two compilations of QEMU.