2009-09-02 09:25:43 +02:00
|
|
|
@c Copyright 2005, 2006, 2009
|
2005-09-30 17:05:07 +02:00
|
|
|
@c Free Software Foundation, Inc.
|
|
|
|
@c This is part of the GAS manual.
|
|
|
|
@c For copying conditions, see the file as.texinfo.
|
|
|
|
@ifset GENERIC
|
|
|
|
@page
|
|
|
|
@node BFIN-Dependent
|
|
|
|
@chapter Blackfin Dependent Features
|
|
|
|
@end ifset
|
|
|
|
@ifclear GENERIC
|
|
|
|
@node Machine Dependencies
|
|
|
|
@chapter Blackfin Dependent Features
|
|
|
|
@end ifclear
|
|
|
|
|
|
|
|
@cindex Blackfin support
|
|
|
|
@menu
|
2009-08-11 20:44:12 +02:00
|
|
|
* Blackfin Options:: Blackfin Options
|
|
|
|
* Blackfin Syntax:: Blackfin Syntax
|
|
|
|
* Blackfin Directives:: Blackfin Directives
|
2005-09-30 17:05:07 +02:00
|
|
|
@end menu
|
|
|
|
|
2009-08-11 20:44:12 +02:00
|
|
|
@node Blackfin Options
|
|
|
|
@section Options
|
|
|
|
@cindex Blackfin options (none)
|
|
|
|
@cindex options for Blackfin (none)
|
|
|
|
|
|
|
|
@table @code
|
|
|
|
|
|
|
|
@cindex @code{-mcpu=} command line option, Blackfin
|
|
|
|
@item -mcpu=@var{processor}@r{[}-@var{sirevision}@r{]}
|
|
|
|
This option specifies the target processor. The optional @var{sirevision}
|
|
|
|
is not used in assembler. It's here such that GCC can easily pass down its
|
|
|
|
@code{-mcpu=} option. The assembler will issue an
|
|
|
|
error message if an attempt is made to assemble an instruction which
|
|
|
|
will not execute on the target processor. The following processor names are
|
|
|
|
recognized:
|
|
|
|
@code{bf522},
|
|
|
|
@code{bf523},
|
|
|
|
@code{bf524},
|
|
|
|
@code{bf525},
|
|
|
|
@code{bf526},
|
|
|
|
@code{bf527},
|
|
|
|
@code{bf531},
|
|
|
|
@code{bf532},
|
|
|
|
@code{bf533},
|
|
|
|
@code{bf534},
|
|
|
|
@code{bf535} (not implemented yet),
|
|
|
|
@code{bf536},
|
|
|
|
@code{bf537},
|
|
|
|
@code{bf538},
|
|
|
|
@code{bf539},
|
|
|
|
@code{bf542},
|
|
|
|
@code{bf542m},
|
|
|
|
@code{bf544},
|
|
|
|
@code{bf544m},
|
|
|
|
@code{bf547},
|
|
|
|
@code{bf547m},
|
|
|
|
@code{bf548},
|
|
|
|
@code{bf548m},
|
|
|
|
@code{bf549},
|
|
|
|
@code{bf549m},
|
|
|
|
and
|
|
|
|
@code{bf561}.
|
|
|
|
|
|
|
|
@end table
|
|
|
|
|
|
|
|
@node Blackfin Syntax
|
2005-09-30 17:05:07 +02:00
|
|
|
@section Syntax
|
2009-08-11 20:44:12 +02:00
|
|
|
@cindex Blackfin syntax
|
|
|
|
@cindex syntax, Blackfin
|
2005-09-30 17:05:07 +02:00
|
|
|
|
|
|
|
@table @code
|
|
|
|
@item Special Characters
|
|
|
|
Assembler input is free format and may appear anywhere on the line.
|
|
|
|
One instruction may extend across multiple lines or more than one
|
|
|
|
instruction may appear on the same line. White space (space, tab,
|
|
|
|
comments or newline) may appear anywhere between tokens. A token must
|
|
|
|
not have embedded spaces. Tokens include numbers, register names,
|
|
|
|
keywords, user identifiers, and also some multicharacter special
|
|
|
|
symbols like "+=", "/*" or "||".
|
|
|
|
|
|
|
|
@item Instruction Delimiting
|
|
|
|
A semicolon must terminate every instruction. Sometimes a complete
|
|
|
|
instruction will consist of more than one operation. There are two
|
|
|
|
cases where this occurs. The first is when two general operations
|
|
|
|
are combined. Normally a comma separates the different parts, as in
|
|
|
|
|
|
|
|
@smallexample
|
|
|
|
a0= r3.h * r2.l, a1 = r3.l * r2.h ;
|
|
|
|
@end smallexample
|
|
|
|
|
|
|
|
The second case occurs when a general instruction is combined with one
|
|
|
|
or two memory references for joint issue. The latter portions are
|
|
|
|
set off by a "||" token.
|
|
|
|
|
|
|
|
@smallexample
|
|
|
|
a0 = r3.h * r2.l || r1 = [p3++] || r4 = [i2++];
|
|
|
|
@end smallexample
|
|
|
|
|
|
|
|
@item Register Names
|
|
|
|
|
|
|
|
The assembler treats register names and instruction keywords in a case
|
|
|
|
insensitive manner. User identifiers are case sensitive. Thus, R3.l,
|
|
|
|
R3.L, r3.l and r3.L are all equivalent input to the assembler.
|
|
|
|
|
|
|
|
Register names are reserved and may not be used as program identifiers.
|
|
|
|
|
|
|
|
Some operations (such as "Move Register") require a register pair.
|
|
|
|
Register pairs are always data registers and are denoted using a colon,
|
|
|
|
eg., R3:2. The larger number must be written firsts. Note that the
|
|
|
|
hardware only supports odd-even pairs, eg., R7:6, R5:4, R3:2, and R1:0.
|
|
|
|
|
|
|
|
Some instructions (such as --SP (Push Multiple)) require a group of
|
|
|
|
adjacent registers. Adjacent registers are denoted in the syntax by
|
|
|
|
the range enclosed in parentheses and separated by a colon, eg., (R7:3).
|
|
|
|
Again, the larger number appears first.
|
|
|
|
|
|
|
|
Portions of a particular register may be individually specified. This
|
|
|
|
is written with a dot (".") following the register name and then a
|
|
|
|
letter denoting the desired portion. For 32-bit registers, ".H"
|
|
|
|
denotes the most significant ("High") portion. ".L" denotes the
|
|
|
|
least-significant portion. The subdivisions of the 40-bit registers
|
|
|
|
are described later.
|
|
|
|
|
|
|
|
@item Accumulators
|
|
|
|
The set of 40-bit registers A1 and A0 that normally contain data that
|
|
|
|
is being manipulated. Each accumulator can be accessed in four ways.
|
|
|
|
|
|
|
|
@table @code
|
|
|
|
@item one 40-bit register
|
|
|
|
The register will be referred to as A1 or A0.
|
|
|
|
@item one 32-bit register
|
|
|
|
The registers are designated as A1.W or A0.W.
|
|
|
|
@item two 16-bit registers
|
|
|
|
The registers are designated as A1.H, A1.L, A0.H or A0.L.
|
|
|
|
@item one 8-bit register
|
|
|
|
The registers are designated as A1.X or A0.X for the bits that
|
|
|
|
extend beyond bit 31.
|
|
|
|
@end table
|
|
|
|
|
|
|
|
@item Data Registers
|
|
|
|
The set of 32-bit registers (R0, R1, R2, R3, R4, R5, R6 and R7) that
|
|
|
|
normally contain data for manipulation. These are abbreviated as
|
|
|
|
D-register or Dreg. Data registers can be accessed as 32-bit registers
|
|
|
|
or as two independent 16-bit registers. The least significant 16 bits
|
2006-07-24 15:49:50 +02:00
|
|
|
of each register is called the "low" half and is designated with ".L"
|
2005-09-30 17:05:07 +02:00
|
|
|
following the register name. The most significant 16 bits are called
|
2006-07-24 15:49:50 +02:00
|
|
|
the "high" half and is designated with ".H" following the name.
|
2005-09-30 17:05:07 +02:00
|
|
|
|
|
|
|
@smallexample
|
|
|
|
R7.L, r2.h, r4.L, R0.H
|
|
|
|
@end smallexample
|
|
|
|
|
|
|
|
@item Pointer Registers
|
|
|
|
The set of 32-bit registers (P0, P1, P2, P3, P4, P5, SP and FP) that
|
|
|
|
normally contain byte addresses of data structures. These are
|
|
|
|
abbreviated as P-register or Preg.
|
|
|
|
|
|
|
|
@smallexample
|
|
|
|
p2, p5, fp, sp
|
|
|
|
@end smallexample
|
|
|
|
|
|
|
|
@item Stack Pointer SP
|
|
|
|
The stack pointer contains the 32-bit address of the last occupied
|
|
|
|
byte location in the stack. The stack grows by decrementing the
|
|
|
|
stack pointer.
|
|
|
|
|
|
|
|
@item Frame Pointer FP
|
|
|
|
The frame pointer contains the 32-bit address of the previous frame
|
|
|
|
pointer in the stack. It is located at the top of a frame.
|
|
|
|
|
|
|
|
@item Loop Top
|
|
|
|
LT0 and LT1. These registers contain the 32-bit address of the top of
|
|
|
|
a zero overhead loop.
|
|
|
|
|
|
|
|
@item Loop Count
|
|
|
|
LC0 and LC1. These registers contain the 32-bit counter of the zero
|
|
|
|
overhead loop executions.
|
|
|
|
|
|
|
|
@item Loop Bottom
|
|
|
|
LB0 and LB1. These registers contain the 32-bit address of the bottom
|
|
|
|
of a zero overhead loop.
|
|
|
|
|
|
|
|
@item Index Registers
|
|
|
|
The set of 32-bit registers (I0, I1, I2, I3) that normally contain byte
|
|
|
|
addresses of data structures. Abbreviated I-register or Ireg.
|
|
|
|
|
|
|
|
@item Modify Registers
|
|
|
|
The set of 32-bit registers (M0, M1, M2, M3) that normally contain
|
|
|
|
offset values that are added and subracted to one of the index
|
|
|
|
registers. Abbreviated as Mreg.
|
|
|
|
|
|
|
|
@item Length Registers
|
|
|
|
The set of 32-bit registers (L0, L1, L2, L3) that normally contain the
|
|
|
|
length in bytes of the circular buffer. Abbreviated as Lreg. Clear
|
|
|
|
the Lreg to disable circular addressing for the corresponding Ireg.
|
|
|
|
|
|
|
|
@item Base Registers
|
|
|
|
The set of 32-bit registers (B0, B1, B2, B3) that normally contain the
|
|
|
|
base address in bytes of the circular buffer. Abbreviated as Breg.
|
|
|
|
|
|
|
|
@item Floating Point
|
|
|
|
The Blackfin family has no hardware floating point but the .float
|
|
|
|
directive generates ieee floating point numbers for use with software
|
|
|
|
floating point libraries.
|
|
|
|
|
|
|
|
@item Blackfin Opcodes
|
|
|
|
For detailed information on the Blackfin machine instruction set, see
|
|
|
|
the Blackfin(r) Processor Instruction Set Reference.
|
|
|
|
|
|
|
|
@end table
|
|
|
|
|
2009-08-11 20:44:12 +02:00
|
|
|
@node Blackfin Directives
|
2005-09-30 17:05:07 +02:00
|
|
|
@section Directives
|
2009-08-11 20:44:12 +02:00
|
|
|
@cindex Blackfin directives
|
|
|
|
@cindex directives, Blackfin
|
2005-09-30 17:05:07 +02:00
|
|
|
|
|
|
|
The following directives are provided for compatibility with the VDSP assembler.
|
|
|
|
|
|
|
|
@table @code
|
|
|
|
@item .byte2
|
|
|
|
Initializes a four byte data object.
|
|
|
|
@item .byte4
|
|
|
|
Initializes a two byte data object.
|
|
|
|
@item .db
|
|
|
|
TBD
|
|
|
|
@item .dd
|
|
|
|
TBD
|
|
|
|
@item .dw
|
|
|
|
TBD
|
|
|
|
@item .var
|
|
|
|
Define and initialize a 32 bit data object.
|
|
|
|
@end table
|