1. Background information
The MIPS architecture, as originally designed and implemented in
mid-1980s has a uniform instruction word size that is 4 bytes, naturally
aligned. As such all MIPS instructions are located at addresses that
have their bits #1 and #0 set to zeroes, and any attempt to execute an
instruction from an address that has any of the two bits set to one
causes an address error exception. This may for example happen when a
jump-register instruction is executed whose register value used as the
jump target has any of these bits set.
Then in mid 1990s LSI sought a way to improve code density for their
TinyRISC family of MIPS cores and invented an alternatively encoded
instruction set in a joint effort with MIPS Technologies (then a
subsidiary of SGI). The new instruction set has been named the MIPS16
ASE (Application-Specific Extension) and uses a variable instruction
word size, which is 2 bytes (as the name of the ASE suggests) for most,
but there are a couple of exceptions that take 4 bytes, and then most of
the 2-byte instructions can be treated with a 2-byte extension prefix to
expand the range of the immediate operands used.
As a result instructions are no longer 4-byte aligned, instead they are
aligned to a multiple of 2. That left the bit #0 still unused for code
references, be it for the standard MIPS (i.e. as originally invented) or
for the MIPS16 instruction set, and based on that observation a clever
trick was invented that on one hand allowed the processor to be
seamlessly switched between the two instruction sets at any time at the
run time while on the other avoided the introduction of any special
control register to do that.
So it is the bit #0 of the instruction address that was chosen as the
selector and named the ISA bit. Any instruction executed at an even
address is interpreted as a standard MIPS instruction (the address still
has to have its bit #1 clear), any instruction executed at an odd
address is interpreted as a MIPS16 instruction.
To switch between modes ordinary jump instructions are used, such as
used for function calls and returns, specifically the bit #0 of the
source register used in jump-register instructions selects the execution
(ISA) mode for the following piece of code to be interpreted in.
Additionally new jump-immediate instructions were added that flipped the
ISA bit to select the opposite mode upon execution. They were
considered necessary to avoid the need to make register jumps in all
cases as the original jump-immediate instructions provided no way to
change the bit #0 at all.
This was all important for cases where standard MIPS and MIPS16 code had
to be mixed, either for compatibility with the existing binary code base
or to access resources not reachable from MIPS16 code (the MIPS16
instruction set only provides access to general-purpose registers, and
not for example floating-point unit registers or privileged coprocessor
0 registers) -- pieces of code in the opposite mode can be executed as
ordinary subroutine calls.
A similar approach has been more recently adopted for the MIPS16
replacement instruction set defined as the so called microMIPS ASE.
This is another instruction set encoding introduced to the MIPS
architecture. Just like the MIPS16 ASE, the microMIPS instruction set
uses a variable-length encoding, where each instruction takes a multiple
of 2 bytes. The ISA bit has been reused and for microMIPS-capable
processors selects between the standard MIPS and the microMIPS mode
instead.
2. Statement of the problem
To put it shortly, MIPS16 and microMIPS code pointers used by GDB are
different to these observed at the run time. This results in the same
expressions being evaluated producing different results in GDB and in
the program being debugged. Obviously it's the results obtained at the
run time that are correct (they define how the program behaves) and
therefore by definition the results obtained in GDB are incorrect.
A bit longer description will record that obviously at the run time the
ISA bit has to be set correctly (refer to background information above
if unsure why so) or the program will not run as expected. This is
recorded in all the executable file structures used at the run time: the
dynamic symbol table (but not always the static one!), the GOT, and
obviously in all the addresses embedded in code or data of the program
itself, calculated by applying the appropriate relocations at the static
link time.
While a program is being processed by GDB, the ISA bit is stripped off
from any code addresses, presumably to make them the same as the
respective raw memory byte address used by the processor to access the
instruction in the instruction fetch access cycle. This stripping is
actually performed outside GDB proper, in BFD, specifically
_bfd_mips_elf_symbol_processing (elfxx-mips.c, see the piece of code at
the very bottom of that function, starting with an: "If this is an
odd-valued function symbol, assume it's a MIPS16 or microMIPS one."
comment).
This function is also responsible for symbol table dumps made by
`objdump' too, so you'll never see the ISA bit reported there by that
tool, you need to use `readelf'.
This is however unlike what is ever done at the run time, the ISA bit
once present is never stripped off, for example a cast like this:
(short *) main
will not strip the ISA bit off and if the resulting pointer is intended
to be used to access instructions as data, for example for software
instruction decoding (like for fault recovery or emulation in a signal
handler) or for self-modifying code then the bit still has to be
stripped off by an explicit AND operation.
This is probably best illustrated with a simple real program example.
Let's consider the following simple program:
$ cat foobar.c
int __attribute__ ((mips16)) foo (void)
{
return 1;
}
int __attribute__ ((mips16)) bar (void)
{
return 2;
}
int __attribute__ ((nomips16)) foo32 (void)
{
return 3;
}
int (*foo32p) (void) = foo32;
int (*foop) (void) = foo;
int fooi = (int) foo;
int
main (void)
{
return foop ();
}
$
This is plain C with no odd tricks, except from the instruction mode
attributes. They are not necessary to trigger this problem, I just put
them here so that the program can be contained in a single source file
and to make it obvious which function is MIPS16 code and which is not.
Let's try it with Linux, so that everyone can repeat this experiment:
$ mips-linux-gnu-gcc -mips16 -g -O2 -o foobar foobar.c
$
Let's have a look at some interesting symbols:
$ mips-linux-gnu-readelf -s foobar | egrep 'table|foo|bar'
Symbol table '.dynsym' contains 7 entries:
Symbol table '.symtab' contains 95 entries:
55: 00000000 0 FILE LOCAL DEFAULT ABS foobar.c
66: 0040068c 4 FUNC GLOBAL DEFAULT [MIPS16] 12 bar
68: 00410848 4 OBJECT GLOBAL DEFAULT 21 foo32p
70: 00410844 4 OBJECT GLOBAL DEFAULT 21 foop
78: 00400684 8 FUNC GLOBAL DEFAULT 12 foo32
80: 00400680 4 FUNC GLOBAL DEFAULT [MIPS16] 12 foo
88: 00410840 4 OBJECT GLOBAL DEFAULT 21 fooi
$
Hmm, no sight of the ISA bit, but notice how foo and bar (but not
foo32!) have been marked as MIPS16 functions (ELF symbol structure's
`st_other' field is used for that).
So let's try to run and poke at this program with GDB. I'll be using a
native system for simplicity (I'll be using ellipses here and there to
remove unrelated clutter):
$ ./foobar
$ echo $?
1
$
So far, so good.
$ gdb ./foobar
[...]
(gdb) break main
Breakpoint 1 at 0x400490: file foobar.c, line 23.
(gdb) run
Starting program: .../foobar
Breakpoint 1, main () at foobar.c:23
23 return foop ();
(gdb)
Yay, it worked! OK, so let's poke at it:
(gdb) print main
$1 = {int (void)} 0x400490 <main>
(gdb) print foo32
$2 = {int (void)} 0x400684 <foo32>
(gdb) print foo32p
$3 = (int (*)(void)) 0x400684 <foo32>
(gdb) print bar
$4 = {int (void)} 0x40068c <bar>
(gdb) print foo
$5 = {int (void)} 0x400680 <foo>
(gdb) print foop
$6 = (int (*)(void)) 0x400681 <foo>
(gdb)
A-ha! Here's the difference and finally the ISA bit!
(gdb) print /x fooi
$7 = 0x400681
(gdb) p/x $pc
p/x $pc
$8 = 0x400491
(gdb)
And here as well...
(gdb) advance foo
foo () at foobar.c:4
4 }
(gdb) disassemble
Dump of assembler code for function foo:
0x00400680 <+0>: jr ra
0x00400682 <+2>: li v0,1
End of assembler dump.
(gdb) finish
Run till exit from #0 foo () at foobar.c:4
main () at foobar.c:24
24 }
Value returned is $9 = 1
(gdb) continue
Continuing.
[Inferior 1 (process 14103) exited with code 01]
(gdb)
So let's be a bit inquisitive...
(gdb) run
Starting program: .../foobar
Breakpoint 1, main () at foobar.c:23
23 return foop ();
(gdb)
Actually we do not like to run foo here at all. Let's run bar instead!
(gdb) set foop = bar
(gdb) print foop
$10 = (int (*)(void)) 0x40068c <bar>
(gdb)
Hmm, no ISA bit. Is it going to work?
(gdb) advance bar
bar () at foobar.c:9
9 }
(gdb) p/x $pc
$11 = 0x40068c
(gdb) disassemble
Dump of assembler code for function bar:
=> 0x0040068c <+0>: jr ra
0x0040068e <+2>: li v0,2
End of assembler dump.
(gdb) finish
Run till exit from #0 bar () at foobar.c:9
Program received signal SIGILL, Illegal instruction.
bar () at foobar.c:9
9 }
(gdb)
Oops!
(gdb) p/x $pc
$12 = 0x40068c
(gdb)
We're still there!
(gdb) continue
Continuing.
Program terminated with signal SIGILL, Illegal instruction.
The program no longer exists.
(gdb)
So let's try something else:
(gdb) run
Starting program: .../foobar
Breakpoint 1, main () at foobar.c:23
23 return foop ();
(gdb) set foop = foo
(gdb) advance foo
foo () at foobar.c:4
4 }
(gdb) disassemble
Dump of assembler code for function foo:
=> 0x00400680 <+0>: jr ra
0x00400682 <+2>: li v0,1
End of assembler dump.
(gdb) finish
Run till exit from #0 foo () at foobar.c:4
Program received signal SIGILL, Illegal instruction.
foo () at foobar.c:4
4 }
(gdb) continue
Continuing.
Program terminated with signal SIGILL, Illegal instruction.
The program no longer exists.
(gdb)
The same problem!
(gdb) run
Starting program:
/net/build2-lucid-cs/scratch/macro/mips-linux-fsf-gcc/isa-bit/foobar
Breakpoint 1, main () at foobar.c:23
23 return foop ();
(gdb) set foop = foo32
(gdb) advance foo32
foo32 () at foobar.c:14
14 }
(gdb) disassemble
Dump of assembler code for function foo32:
=> 0x00400684 <+0>: jr ra
0x00400688 <+4>: li v0,3
End of assembler dump.
(gdb) finish
Run till exit from #0 foo32 () at foobar.c:14
main () at foobar.c:24
24 }
Value returned is $14 = 3
(gdb) continue
Continuing.
[Inferior 1 (process 14113) exited with code 03]
(gdb)
That did work though, so it's the ISA bit only!
(gdb) quit
Enough!
That's the tip of the iceberg only though. So let's rebuild the
executable with some dynamic symbols:
$ mips-linux-gnu-gcc -mips16 -Wl,--export-dynamic -g -O2 -o foobar-dyn foobar.c
$ mips-linux-gnu-readelf -s foobar-dyn | egrep 'table|foo|bar'
Symbol table '.dynsym' contains 32 entries:
6: 004009cd 4 FUNC GLOBAL DEFAULT 12 bar
8: 00410b88 4 OBJECT GLOBAL DEFAULT 21 foo32p
9: 00410b84 4 OBJECT GLOBAL DEFAULT 21 foop
15: 004009c4 8 FUNC GLOBAL DEFAULT 12 foo32
17: 004009c1 4 FUNC GLOBAL DEFAULT 12 foo
25: 00410b80 4 OBJECT GLOBAL DEFAULT 21 fooi
Symbol table '.symtab' contains 95 entries:
55: 00000000 0 FILE LOCAL DEFAULT ABS foobar.c
69: 004009cd 4 FUNC GLOBAL DEFAULT 12 bar
71: 00410b88 4 OBJECT GLOBAL DEFAULT 21 foo32p
72: 00410b84 4 OBJECT GLOBAL DEFAULT 21 foop
79: 004009c4 8 FUNC GLOBAL DEFAULT 12 foo32
81: 004009c1 4 FUNC GLOBAL DEFAULT 12 foo
89: 00410b80 4 OBJECT GLOBAL DEFAULT 21 fooi
$
OK, now the ISA bit is there for a change, but the MIPS16 `st_other'
attribute gone, hmm... What does `objdump' do then:
$ mips-linux-gnu-objdump -Tt foobar-dyn | egrep 'SYMBOL|foo|bar'
foobar-dyn: file format elf32-tradbigmips
SYMBOL TABLE:
00000000 l df *ABS* 00000000 foobar.c
004009cc g F .text 00000004 0xf0 bar
00410b88 g O .data 00000004 foo32p
00410b84 g O .data 00000004 foop
004009c4 g F .text 00000008 foo32
004009c0 g F .text 00000004 0xf0 foo
00410b80 g O .data 00000004 fooi
DYNAMIC SYMBOL TABLE:
004009cc g DF .text 00000004 Base 0xf0 bar
00410b88 g DO .data 00000004 Base foo32p
00410b84 g DO .data 00000004 Base foop
004009c4 g DF .text 00000008 Base foo32
004009c0 g DF .text 00000004 Base 0xf0 foo
00410b80 g DO .data 00000004 Base fooi
$
Hmm, the attribute (0xf0, printed raw) is back, and the ISA bit gone
again.
Let's have a look at some DWARF-2 records GDB uses (I'll be stripping
off a lot here for brevity) -- debug info:
$ mips-linux-gnu-readelf -wi foobar
Contents of the .debug_info section:
[...]
Compilation Unit @ offset 0x88:
Length: 0xbb (32-bit)
Version: 4
Abbrev Offset: 62
Pointer Size: 4
<0><93>: Abbrev Number: 1 (DW_TAG_compile_unit)
<94> DW_AT_producer : (indirect string, offset: 0x19e): GNU C 4.8.0 20120513 (experimental) -meb -mips16 -march=mips32r2 -mhard-float -mllsc -mplt -mno-synci -mno-shared -mabi=32 -g -O2
<98> DW_AT_language : 1 (ANSI C)
<99> DW_AT_name : (indirect string, offset: 0x190): foobar.c
<9d> DW_AT_comp_dir : (indirect string, offset: 0x225): [...]
<a1> DW_AT_ranges : 0x0
<a5> DW_AT_low_pc : 0x0
<a9> DW_AT_stmt_list : 0x27
<1><ad>: Abbrev Number: 2 (DW_TAG_subprogram)
<ae> DW_AT_external : 1
<ae> DW_AT_name : foo
<b2> DW_AT_decl_file : 1
<b3> DW_AT_decl_line : 1
<b4> DW_AT_prototyped : 1
<b4> DW_AT_type : <0xc2>
<b8> DW_AT_low_pc : 0x400680
<bc> DW_AT_high_pc : 0x400684
<c0> DW_AT_frame_base : 1 byte block: 9c (DW_OP_call_frame_cfa)
<c2> DW_AT_GNU_all_call_sites: 1
<1><c2>: Abbrev Number: 3 (DW_TAG_base_type)
<c3> DW_AT_byte_size : 4
<c4> DW_AT_encoding : 5 (signed)
<c5> DW_AT_name : int
<1><c9>: Abbrev Number: 4 (DW_TAG_subprogram)
<ca> DW_AT_external : 1
<ca> DW_AT_name : (indirect string, offset: 0x18a): foo32
<ce> DW_AT_decl_file : 1
<cf> DW_AT_decl_line : 11
<d0> DW_AT_prototyped : 1
<d0> DW_AT_type : <0xc2>
<d4> DW_AT_low_pc : 0x400684
<d8> DW_AT_high_pc : 0x40068c
<dc> DW_AT_frame_base : 1 byte block: 9c (DW_OP_call_frame_cfa)
<de> DW_AT_GNU_all_call_sites: 1
<1><de>: Abbrev Number: 2 (DW_TAG_subprogram)
<df> DW_AT_external : 1
<df> DW_AT_name : bar
<e3> DW_AT_decl_file : 1
<e4> DW_AT_decl_line : 6
<e5> DW_AT_prototyped : 1
<e5> DW_AT_type : <0xc2>
<e9> DW_AT_low_pc : 0x40068c
<ed> DW_AT_high_pc : 0x400690
<f1> DW_AT_frame_base : 1 byte block: 9c (DW_OP_call_frame_cfa)
<f3> DW_AT_GNU_all_call_sites: 1
<1><f3>: Abbrev Number: 5 (DW_TAG_subprogram)
<f4> DW_AT_external : 1
<f4> DW_AT_name : (indirect string, offset: 0x199): main
<f8> DW_AT_decl_file : 1
<f9> DW_AT_decl_line : 21
<fa> DW_AT_prototyped : 1
<fa> DW_AT_type : <0xc2>
<fe> DW_AT_low_pc : 0x400490
<102> DW_AT_high_pc : 0x4004a4
<106> DW_AT_frame_base : 1 byte block: 9c (DW_OP_call_frame_cfa)
<108> DW_AT_GNU_all_tail_call_sites: 1
[...]
$
-- no sign of the ISA bit anywhere -- frame info:
$ mips-linux-gnu-readelf -wf foobar
[...]
Contents of the .debug_frame section:
00000000 0000000c ffffffff CIE
Version: 1
Augmentation: ""
Code alignment factor: 1
Data alignment factor: -4
Return address column: 31
DW_CFA_def_cfa_register: r29
DW_CFA_nop
00000010 0000000c 00000000 FDE cie=00000000 pc=00400680..00400684
00000020 0000000c 00000000 FDE cie=00000000 pc=00400684..0040068c
00000030 0000000c 00000000 FDE cie=00000000 pc=0040068c..00400690
00000040 00000018 00000000 FDE cie=00000000 pc=00400490..004004a4
DW_CFA_advance_loc: 6 to 00400496
DW_CFA_def_cfa_offset: 32
DW_CFA_offset: r31 at cfa-4
DW_CFA_advance_loc: 6 to 0040049c
DW_CFA_restore: r31
DW_CFA_def_cfa_offset: 0
DW_CFA_nop
DW_CFA_nop
DW_CFA_nop
[...]
$
-- no sign of the ISA bit anywhere -- range info (GDB doesn't use arange):
$ mips-linux-gnu-readelf -wR foobar
Contents of the .debug_ranges section:
Offset Begin End
00000000 00400680 00400690
00000000 00400490 004004a4
00000000 <End of list>
$
-- no sign of the ISA bit anywhere -- line info:
$ mips-linux-gnu-readelf -wl foobar
Raw dump of debug contents of section .debug_line:
[...]
Offset: 0x27
Length: 78
DWARF Version: 2
Prologue Length: 31
Minimum Instruction Length: 1
Initial value of 'is_stmt': 1
Line Base: -5
Line Range: 14
Opcode Base: 13
Opcodes:
Opcode 1 has 0 args
Opcode 2 has 1 args
Opcode 3 has 1 args
Opcode 4 has 1 args
Opcode 5 has 1 args
Opcode 6 has 0 args
Opcode 7 has 0 args
Opcode 8 has 0 args
Opcode 9 has 1 args
Opcode 10 has 0 args
Opcode 11 has 0 args
Opcode 12 has 1 args
The Directory Table is empty.
The File Name Table:
Entry Dir Time Size Name
1 0 0 0 foobar.c
Line Number Statements:
Extended opcode 2: set Address to 0x400681
Special opcode 6: advance Address by 0 to 0x400681 and Line by 1 to 2
Special opcode 7: advance Address by 0 to 0x400681 and Line by 2 to 4
Special opcode 55: advance Address by 3 to 0x400684 and Line by 8 to 12
Special opcode 7: advance Address by 0 to 0x400684 and Line by 2 to 14
Advance Line by -7 to 7
Special opcode 131: advance Address by 9 to 0x40068d and Line by 0 to 7
Special opcode 7: advance Address by 0 to 0x40068d and Line by 2 to 9
Advance PC by 3 to 0x400690
Extended opcode 1: End of Sequence
Extended opcode 2: set Address to 0x400491
Advance Line by 21 to 22
Copy
Special opcode 6: advance Address by 0 to 0x400491 and Line by 1 to 23
Special opcode 60: advance Address by 4 to 0x400495 and Line by -1 to 22
Special opcode 34: advance Address by 2 to 0x400497 and Line by 1 to 23
Special opcode 62: advance Address by 4 to 0x40049b and Line by 1 to 24
Special opcode 32: advance Address by 2 to 0x40049d and Line by -1 to 23
Special opcode 6: advance Address by 0 to 0x40049d and Line by 1 to 24
Advance PC by 7 to 0x4004a4
Extended opcode 1: End of Sequence
[...]
-- a-ha, the ISA bit is there! However it's not always right for some
reason, I don't have a small test case to show it, but here's an excerpt
from MIPS16 libc, a prologue of a function:
00019630 <__libc_init_first>:
19630: e8a0 jrc ra
19632: 6500 nop
00019634 <_init>:
19634: f000 6a11 li v0,17
19638: f7d8 0b08 la v1,15e00 <_DYNAMIC+0x15c54>
1963c: f400 3240 sll v0,16
19640: e269 addu v0,v1
19642: 659a move gp,v0
19644: 64f6 save 48,ra,s0-s1
19646: 671c move s0,gp
19648: d204 sw v0,16(sp)
1964a: f352 984c lw v0,-27828(s0)
1964e: 6724 move s1,a0
and the corresponding DWARF-2 line info:
Line Number Statements:
Extended opcode 2: set Address to 0x19631
Advance Line by 44 to 45
Copy
Special opcode 8: advance Address by 0 to 0x19631 and Line by 3 to 48
Special opcode 66: advance Address by 4 to 0x19635 and Line by 5 to 53
Advance PC by constant 17 to 0x19646
Special opcode 25: advance Address by 1 to 0x19647 and Line by 6 to 59
Advance Line by -6 to 53
Special opcode 33: advance Address by 2 to 0x19649 and Line by 0 to 53
Special opcode 39: advance Address by 2 to 0x1964b and Line by 6 to 59
Advance Line by -6 to 53
Special opcode 61: advance Address by 4 to 0x1964f and Line by 0 to 53
-- see that "Advance PC by constant 17" there? It clears the ISA bit,
however code at 0x19646 is not standard MIPS code at all. For some
reason the constant is always 17, I've never seen DW_LNS_const_add_pc
used with any other value -- is that a binutils bug or what?
3. Solution:
I think we should retain the value of the ISA bit in code references,
that is effectively treat them as cookies as they indeed are (although
trivially calculated) rather than raw memory byte addresses.
In a perfect world both the static symbol table and the respective
DWARF-2 records should be fixed to include the ISA bit in all the cases.
I think however that this is infeasible.
All the uses of `_bfd_mips_elf_symbol_processing' can not necessarily be
tracked down. This function is used by `elf_slurp_symbol_table' that in
turn is used by `bfd_canonicalize_symtab' and
`bfd_canonicalize_dynamic_symtab', which are public interfaces.
Similarly DWARF-2 records are used outside GDB, one notable if a bit
questionable is the exception unwinder (libgcc/unwind-dw2.c) -- I have
identified at least bits in `execute_cfa_program' and
`uw_frame_state_for', both around the calls to `_Unwind_IsSignalFrame',
that would need an update as they effectively flip the ISA bit freely;
see also the comment about MASK_RETURN_ADDR in gcc/config/mips/mips.h.
But there may be more places. Any change in how DWARF-2 records are
produced would require an update there and would cause compatibility
problems with libgcc.a binaries already distributed; given that this is
a static library a complex change involving function renames would
likely be required.
I propose therefore to accept the existing inconsistencies and deal with
them entirely within GDB. I have figured out that the ISA bit lost in
various places can still be recovered as long as we have symbol
information -- that'll have the `st_other' attribute correctly set to
one of standard MIPS/MIPS16/microMIPS encoding.
Here's the resulting change. It adds a couple of new `gdbarch' hooks,
one to update symbol information with the ISA bit lost in
`_bfd_mips_elf_symbol_processing', and two other ones to adjust DWARF-2
records as they're processed. The ISA bit is set in each address
handled according to information retrieved from the symbol table for the
symbol spanning the address if any; limits are adjusted based on the
address they point to related to the respective base address.
Additionally minimal symbol information has to be adjusted accordingly
in its gdbarch hook.
With these changes in place some complications with ISA bit juggling in
the PC that never fully worked can be removed from the MIPS backend.
Conversely, the generic dynamic linker event special breakpoint symbol
handler has to be updated to call the minimal symbol gdbarch hook to
record that the symbol is a MIPS16 or microMIPS address if applicable or
the breakpoint will be set at the wrong address and either fail to work
or cause SIGTRAPs (this is because the symbol is handled early on and
bypasses regular symbol processing).
4. Results obtained
The change fixes the example above -- to repeat only the crucial steps:
(gdb) break main
Breakpoint 1 at 0x400491: file foobar.c, line 23.
(gdb) run
Starting program: .../foobar
Breakpoint 1, main () at foobar.c:23
23 return foop ();
(gdb) print foo
$1 = {int (void)} 0x400681 <foo>
(gdb) set foop = bar
(gdb) advance bar
bar () at foobar.c:9
9 }
(gdb) disassemble
Dump of assembler code for function bar:
=> 0x0040068d <+0>: jr ra
0x0040068f <+2>: li v0,2
End of assembler dump.
(gdb) finish
Run till exit from #0 bar () at foobar.c:9
main () at foobar.c:24
24 }
Value returned is $2 = 2
(gdb) continue
Continuing.
[Inferior 1 (process 14128) exited with code 02]
(gdb)
-- excellent!
The change removes about 90 failures per MIPS16 multilib in mips-sde-elf
testing too, results for MIPS16 are now similar to that for standard
MIPS; microMIPS results are a bit worse because of host-I/O problems in
QEMU used instead of MIPSsim for microMIPS testing only:
=== gdb Summary ===
# of expected passes 14299
# of unexpected failures 187
# of expected failures 56
# of known failures 58
# of unresolved testcases 11
# of untested testcases 52
# of unsupported tests 174
MIPS16:
=== gdb Summary ===
# of expected passes 14298
# of unexpected failures 187
# of unexpected successes 2
# of expected failures 54
# of known failures 58
# of unresolved testcases 12
# of untested testcases 52
# of unsupported tests 174
microMIPS:
=== gdb Summary ===
# of expected passes 14149
# of unexpected failures 201
# of unexpected successes 2
# of expected failures 54
# of known failures 58
# of unresolved testcases 7
# of untested testcases 53
# of unsupported tests 175
2014-12-12 Maciej W. Rozycki <macro@codesourcery.com>
Maciej W. Rozycki <macro@mips.com>
Pedro Alves <pedro@codesourcery.com>
gdb/
* gdbarch.sh (elf_make_msymbol_special): Change type to `F',
remove `predefault' and `invalid_p' initializers.
(make_symbol_special): New architecture method.
(adjust_dwarf2_addr, adjust_dwarf2_line): Likewise.
(objfile, symbol): New declarations.
* arch-utils.h (default_elf_make_msymbol_special): Remove
prototype.
(default_make_symbol_special): New prototype.
(default_adjust_dwarf2_addr): Likewise.
(default_adjust_dwarf2_line): Likewise.
* mips-tdep.h (mips_unmake_compact_addr): New prototype.
* arch-utils.c (default_elf_make_msymbol_special): Remove
function.
(default_make_symbol_special): New function.
(default_adjust_dwarf2_addr): Likewise.
(default_adjust_dwarf2_line): Likewise.
* dwarf2-frame.c (decode_frame_entry_1): Call
`gdbarch_adjust_dwarf2_addr'.
* dwarf2loc.c (dwarf2_find_location_expression): Likewise.
* dwarf2read.c (create_addrmap_from_index): Likewise.
(process_psymtab_comp_unit_reader): Likewise.
(add_partial_symbol): Likewise.
(add_partial_subprogram): Likewise.
(process_full_comp_unit): Likewise.
(read_file_scope): Likewise.
(read_func_scope): Likewise. Call `gdbarch_make_symbol_special'.
(read_lexical_block_scope): Call `gdbarch_adjust_dwarf2_addr'.
(read_call_site_scope): Likewise.
(dwarf2_ranges_read): Likewise.
(dwarf2_record_block_ranges): Likewise.
(read_attribute_value): Likewise.
(dwarf_decode_lines_1): Call `gdbarch_adjust_dwarf2_line'.
(new_symbol_full): Call `gdbarch_adjust_dwarf2_addr'.
* elfread.c (elf_symtab_read): Don't call
`gdbarch_elf_make_msymbol_special' if unset.
* mips-linux-tdep.c (micromips_linux_sigframe_validate): Strip
the ISA bit from the PC.
* mips-tdep.c (mips_unmake_compact_addr): New function.
(mips_elf_make_msymbol_special): Set the ISA bit in the symbol's
address appropriately.
(mips_make_symbol_special): New function.
(mips_pc_is_mips): Set the ISA bit before symbol lookup.
(mips_pc_is_mips16): Likewise.
(mips_pc_is_micromips): Likewise.
(mips_pc_isa): Likewise.
(mips_adjust_dwarf2_addr): New function.
(mips_adjust_dwarf2_line): Likewise.
(mips_read_pc, mips_unwind_pc): Keep the ISA bit.
(mips_addr_bits_remove): Likewise.
(mips_skip_trampoline_code): Likewise.
(mips_write_pc): Don't set the ISA bit.
(mips_eabi_push_dummy_call): Likewise.
(mips_o64_push_dummy_call): Likewise.
(mips_gdbarch_init): Install `mips_make_symbol_special',
`mips_adjust_dwarf2_addr' and `mips_adjust_dwarf2_line' gdbarch
handlers.
* solib.c (gdb_bfd_lookup_symbol_from_symtab): Get
target-specific symbol address adjustments.
* gdbarch.h: Regenerate.
* gdbarch.c: Regenerate.
2014-12-12 Maciej W. Rozycki <macro@codesourcery.com>
gdb/testsuite/
* gdb.base/func-ptrs.c: New file.
* gdb.base/func-ptrs.exp: New file.
I am just not sure if we should go the route of
struct objfile * -> const struct objfile *
or the other way of:
const struct objfile * -> struct objfile *
Normally const adding is better but here I do not see much useful to have any
struct objfile * const and then it just causes pointer compatibility problems.
On Wed, 03 Dec 2014 18:18:44 +0100, Doug Evans wrote:
struct objfile is one case where I've decided to just leave the const
out and not worry about it.
gdb/ChangeLog
2014-12-05 Jan Kratochvil <jan.kratochvil@redhat.com>
Remove const from struct objfile *.
* solib-darwin.c, solib-spu.c, solib-svr4.c, solib.c, solist.h,
symtab.c, symtab.h: In these files.
* solib.c (solib_read_symbols): Delete "Loaded symbols for ..."
message, it is redundant with "Reading symbols from ..." message.
testsuite/
* gdb.base/print-symbol-loading.exp (test_load_core): Update.
(test_load_shlib): Update.
This constifies the "pattern" argument to solib_add.
2014-07-24 Tom Tromey <tromey@redhat.com>
* solib.c (solib_add): Make "pattern" const.
* solib.h (solib_add): Update.
* NEWS: Mention it.
* solib.c (solib_read_symbols): Only print symbol loading messages
if requested.
(solib_add): If symbol loading is in "brief" mode, notify user
symbols are being loaded.
(reload_shared_libraries_1): Ditto.
* symfile.c (print_symbol_loading_off): New static global.
(print_symbol_loading_brief): New static global.
(print_symbol_loading_full): New static global.
(print_symbol_loading_enums): New static global.
(print_symbol_loading): New static global.
(print_symbol_loading_p): New function.
(symbol_file_add_with_addrs): Only print symbol loading messages
if requested.
(_initialize_symfile): Register "print symbol-loading" set/show
command.
* symfile.h (print_symbol_loading_p): Declare.
doc/
* gdb.texinfo (Symbols): Document set/show print symbol-loading.
testsuite/
* gdb.base/print-symbol-loading-lib.c: New file.
* gdb.base/print-symbol-loading-main.c: New file.
* gdb.base/print-symbol-loading.exp: New file.
This reverts commit 07293be448, as it
causes an unintended change of behavior with GDB/MI's =library-loaded
events: The host-name="<path>" part of the event is now showing the
target-side path instead of the host-side path.
This revert affects Darwin and AIX systems, however, where the BFD
is either artificial or icomplete, leading to the outputt of
"info shared" not containing the information we'd like. For instance,
on Darwin, we would see:
(top-gdb) info shared
From To Syms Read Shared Object Library
0x00007fff8d060de4 0x00007fff8d09ce1f Yes (*) i386:x86-64
0x00007fff8af08b10 0x00007fff8b1c6f73 Yes (*) i386:x86-64
To compensate for that, we overwrite the filename of the associated bfd.
gdb/ChangeLog:
Revert the following commit:
* solib.c (solib_map_sections): Remove code overwriting
SO->SO_NAME with the bfd's filename.
Make the following changes required after the revert above:
* solib-aix.c (solib_aix_bfd_open): Set the filename of the
returned bfd to a copy of the synthetic pathname.
* solib-darwin.c (darwin_bfd_open): Set the filename of the
returned bfd to a copy of PATHNAME.
This removes gdb_string.h. This patch is purely mechanical. I
created it by running the two commands:
git rm common/gdb_string.h
perl -pi -e's/"gdb_string.h"/<string.h>/;' *.[chyl] */*.[chyl]
2013-11-18 Tom Tromey <tromey@redhat.com>
* common/gdb_string.h: Remove.
* aarch64-tdep.c: Use string.h, not gdb_string.h.
* ada-exp.y: Use string.h, not gdb_string.h.
* ada-lang.c: Use string.h, not gdb_string.h.
* ada-lex.l: Use string.h, not gdb_string.h.
* ada-typeprint.c: Use string.h, not gdb_string.h.
* ada-valprint.c: Use string.h, not gdb_string.h.
* aix-thread.c: Use string.h, not gdb_string.h.
* alpha-linux-tdep.c: Use string.h, not gdb_string.h.
* alpha-mdebug-tdep.c: Use string.h, not gdb_string.h.
* alpha-nat.c: Use string.h, not gdb_string.h.
* alpha-osf1-tdep.c: Use string.h, not gdb_string.h.
* alpha-tdep.c: Use string.h, not gdb_string.h.
* alphanbsd-tdep.c: Use string.h, not gdb_string.h.
* amd64-dicos-tdep.c: Use string.h, not gdb_string.h.
* amd64-linux-nat.c: Use string.h, not gdb_string.h.
* amd64-linux-tdep.c: Use string.h, not gdb_string.h.
* amd64-nat.c: Use string.h, not gdb_string.h.
* amd64-sol2-tdep.c: Use string.h, not gdb_string.h.
* amd64fbsd-tdep.c: Use string.h, not gdb_string.h.
* amd64obsd-tdep.c: Use string.h, not gdb_string.h.
* arch-utils.c: Use string.h, not gdb_string.h.
* arm-linux-nat.c: Use string.h, not gdb_string.h.
* arm-linux-tdep.c: Use string.h, not gdb_string.h.
* arm-tdep.c: Use string.h, not gdb_string.h.
* arm-wince-tdep.c: Use string.h, not gdb_string.h.
* armbsd-tdep.c: Use string.h, not gdb_string.h.
* armnbsd-nat.c: Use string.h, not gdb_string.h.
* armnbsd-tdep.c: Use string.h, not gdb_string.h.
* armobsd-tdep.c: Use string.h, not gdb_string.h.
* avr-tdep.c: Use string.h, not gdb_string.h.
* ax-gdb.c: Use string.h, not gdb_string.h.
* ax-general.c: Use string.h, not gdb_string.h.
* bcache.c: Use string.h, not gdb_string.h.
* bfin-tdep.c: Use string.h, not gdb_string.h.
* breakpoint.c: Use string.h, not gdb_string.h.
* build-id.c: Use string.h, not gdb_string.h.
* buildsym.c: Use string.h, not gdb_string.h.
* c-exp.y: Use string.h, not gdb_string.h.
* c-lang.c: Use string.h, not gdb_string.h.
* c-typeprint.c: Use string.h, not gdb_string.h.
* c-valprint.c: Use string.h, not gdb_string.h.
* charset.c: Use string.h, not gdb_string.h.
* cli-out.c: Use string.h, not gdb_string.h.
* cli/cli-cmds.c: Use string.h, not gdb_string.h.
* cli/cli-decode.c: Use string.h, not gdb_string.h.
* cli/cli-dump.c: Use string.h, not gdb_string.h.
* cli/cli-interp.c: Use string.h, not gdb_string.h.
* cli/cli-logging.c: Use string.h, not gdb_string.h.
* cli/cli-script.c: Use string.h, not gdb_string.h.
* cli/cli-setshow.c: Use string.h, not gdb_string.h.
* cli/cli-utils.c: Use string.h, not gdb_string.h.
* coffread.c: Use string.h, not gdb_string.h.
* common/common-utils.c: Use string.h, not gdb_string.h.
* common/filestuff.c: Use string.h, not gdb_string.h.
* common/linux-procfs.c: Use string.h, not gdb_string.h.
* common/linux-ptrace.c: Use string.h, not gdb_string.h.
* common/signals.c: Use string.h, not gdb_string.h.
* common/vec.h: Use string.h, not gdb_string.h.
* core-regset.c: Use string.h, not gdb_string.h.
* corefile.c: Use string.h, not gdb_string.h.
* corelow.c: Use string.h, not gdb_string.h.
* cp-abi.c: Use string.h, not gdb_string.h.
* cp-support.c: Use string.h, not gdb_string.h.
* cp-valprint.c: Use string.h, not gdb_string.h.
* cris-tdep.c: Use string.h, not gdb_string.h.
* d-lang.c: Use string.h, not gdb_string.h.
* dbxread.c: Use string.h, not gdb_string.h.
* dcache.c: Use string.h, not gdb_string.h.
* demangle.c: Use string.h, not gdb_string.h.
* dicos-tdep.c: Use string.h, not gdb_string.h.
* disasm.c: Use string.h, not gdb_string.h.
* doublest.c: Use string.h, not gdb_string.h.
* dsrec.c: Use string.h, not gdb_string.h.
* dummy-frame.c: Use string.h, not gdb_string.h.
* dwarf2-frame.c: Use string.h, not gdb_string.h.
* dwarf2loc.c: Use string.h, not gdb_string.h.
* dwarf2read.c: Use string.h, not gdb_string.h.
* elfread.c: Use string.h, not gdb_string.h.
* environ.c: Use string.h, not gdb_string.h.
* eval.c: Use string.h, not gdb_string.h.
* event-loop.c: Use string.h, not gdb_string.h.
* exceptions.c: Use string.h, not gdb_string.h.
* exec.c: Use string.h, not gdb_string.h.
* expprint.c: Use string.h, not gdb_string.h.
* f-exp.y: Use string.h, not gdb_string.h.
* f-lang.c: Use string.h, not gdb_string.h.
* f-typeprint.c: Use string.h, not gdb_string.h.
* f-valprint.c: Use string.h, not gdb_string.h.
* fbsd-nat.c: Use string.h, not gdb_string.h.
* findcmd.c: Use string.h, not gdb_string.h.
* findvar.c: Use string.h, not gdb_string.h.
* fork-child.c: Use string.h, not gdb_string.h.
* frame.c: Use string.h, not gdb_string.h.
* frv-linux-tdep.c: Use string.h, not gdb_string.h.
* frv-tdep.c: Use string.h, not gdb_string.h.
* gdb.c: Use string.h, not gdb_string.h.
* gdb_bfd.c: Use string.h, not gdb_string.h.
* gdbarch.c: Use string.h, not gdb_string.h.
* gdbtypes.c: Use string.h, not gdb_string.h.
* gnu-nat.c: Use string.h, not gdb_string.h.
* gnu-v2-abi.c: Use string.h, not gdb_string.h.
* gnu-v3-abi.c: Use string.h, not gdb_string.h.
* go-exp.y: Use string.h, not gdb_string.h.
* go-lang.c: Use string.h, not gdb_string.h.
* go32-nat.c: Use string.h, not gdb_string.h.
* hppa-hpux-tdep.c: Use string.h, not gdb_string.h.
* hppa-linux-nat.c: Use string.h, not gdb_string.h.
* hppanbsd-tdep.c: Use string.h, not gdb_string.h.
* hppaobsd-tdep.c: Use string.h, not gdb_string.h.
* i386-cygwin-tdep.c: Use string.h, not gdb_string.h.
* i386-dicos-tdep.c: Use string.h, not gdb_string.h.
* i386-linux-nat.c: Use string.h, not gdb_string.h.
* i386-linux-tdep.c: Use string.h, not gdb_string.h.
* i386-nto-tdep.c: Use string.h, not gdb_string.h.
* i386-sol2-tdep.c: Use string.h, not gdb_string.h.
* i386-tdep.c: Use string.h, not gdb_string.h.
* i386bsd-tdep.c: Use string.h, not gdb_string.h.
* i386gnu-nat.c: Use string.h, not gdb_string.h.
* i386nbsd-tdep.c: Use string.h, not gdb_string.h.
* i386obsd-tdep.c: Use string.h, not gdb_string.h.
* i387-tdep.c: Use string.h, not gdb_string.h.
* ia64-libunwind-tdep.c: Use string.h, not gdb_string.h.
* ia64-linux-nat.c: Use string.h, not gdb_string.h.
* inf-child.c: Use string.h, not gdb_string.h.
* inf-ptrace.c: Use string.h, not gdb_string.h.
* inf-ttrace.c: Use string.h, not gdb_string.h.
* infcall.c: Use string.h, not gdb_string.h.
* infcmd.c: Use string.h, not gdb_string.h.
* inflow.c: Use string.h, not gdb_string.h.
* infrun.c: Use string.h, not gdb_string.h.
* interps.c: Use string.h, not gdb_string.h.
* iq2000-tdep.c: Use string.h, not gdb_string.h.
* irix5-nat.c: Use string.h, not gdb_string.h.
* jv-exp.y: Use string.h, not gdb_string.h.
* jv-lang.c: Use string.h, not gdb_string.h.
* jv-typeprint.c: Use string.h, not gdb_string.h.
* jv-valprint.c: Use string.h, not gdb_string.h.
* language.c: Use string.h, not gdb_string.h.
* linux-fork.c: Use string.h, not gdb_string.h.
* linux-nat.c: Use string.h, not gdb_string.h.
* lm32-tdep.c: Use string.h, not gdb_string.h.
* m2-exp.y: Use string.h, not gdb_string.h.
* m2-typeprint.c: Use string.h, not gdb_string.h.
* m32c-tdep.c: Use string.h, not gdb_string.h.
* m32r-linux-nat.c: Use string.h, not gdb_string.h.
* m32r-linux-tdep.c: Use string.h, not gdb_string.h.
* m32r-rom.c: Use string.h, not gdb_string.h.
* m32r-tdep.c: Use string.h, not gdb_string.h.
* m68hc11-tdep.c: Use string.h, not gdb_string.h.
* m68k-tdep.c: Use string.h, not gdb_string.h.
* m68kbsd-tdep.c: Use string.h, not gdb_string.h.
* m68klinux-nat.c: Use string.h, not gdb_string.h.
* m68klinux-tdep.c: Use string.h, not gdb_string.h.
* m88k-tdep.c: Use string.h, not gdb_string.h.
* macrocmd.c: Use string.h, not gdb_string.h.
* main.c: Use string.h, not gdb_string.h.
* mdebugread.c: Use string.h, not gdb_string.h.
* mem-break.c: Use string.h, not gdb_string.h.
* memattr.c: Use string.h, not gdb_string.h.
* memory-map.c: Use string.h, not gdb_string.h.
* mep-tdep.c: Use string.h, not gdb_string.h.
* mi/mi-cmd-break.c: Use string.h, not gdb_string.h.
* mi/mi-cmd-disas.c: Use string.h, not gdb_string.h.
* mi/mi-cmd-env.c: Use string.h, not gdb_string.h.
* mi/mi-cmd-stack.c: Use string.h, not gdb_string.h.
* mi/mi-cmd-var.c: Use string.h, not gdb_string.h.
* mi/mi-cmds.c: Use string.h, not gdb_string.h.
* mi/mi-console.c: Use string.h, not gdb_string.h.
* mi/mi-getopt.c: Use string.h, not gdb_string.h.
* mi/mi-interp.c: Use string.h, not gdb_string.h.
* mi/mi-main.c: Use string.h, not gdb_string.h.
* mi/mi-parse.c: Use string.h, not gdb_string.h.
* microblaze-rom.c: Use string.h, not gdb_string.h.
* microblaze-tdep.c: Use string.h, not gdb_string.h.
* mingw-hdep.c: Use string.h, not gdb_string.h.
* minidebug.c: Use string.h, not gdb_string.h.
* minsyms.c: Use string.h, not gdb_string.h.
* mips-irix-tdep.c: Use string.h, not gdb_string.h.
* mips-linux-tdep.c: Use string.h, not gdb_string.h.
* mips-tdep.c: Use string.h, not gdb_string.h.
* mips64obsd-tdep.c: Use string.h, not gdb_string.h.
* mipsnbsd-tdep.c: Use string.h, not gdb_string.h.
* mipsread.c: Use string.h, not gdb_string.h.
* mn10300-linux-tdep.c: Use string.h, not gdb_string.h.
* mn10300-tdep.c: Use string.h, not gdb_string.h.
* monitor.c: Use string.h, not gdb_string.h.
* moxie-tdep.c: Use string.h, not gdb_string.h.
* mt-tdep.c: Use string.h, not gdb_string.h.
* nbsd-tdep.c: Use string.h, not gdb_string.h.
* nios2-linux-tdep.c: Use string.h, not gdb_string.h.
* nto-procfs.c: Use string.h, not gdb_string.h.
* nto-tdep.c: Use string.h, not gdb_string.h.
* objc-lang.c: Use string.h, not gdb_string.h.
* objfiles.c: Use string.h, not gdb_string.h.
* opencl-lang.c: Use string.h, not gdb_string.h.
* osabi.c: Use string.h, not gdb_string.h.
* osdata.c: Use string.h, not gdb_string.h.
* p-exp.y: Use string.h, not gdb_string.h.
* p-lang.c: Use string.h, not gdb_string.h.
* p-typeprint.c: Use string.h, not gdb_string.h.
* parse.c: Use string.h, not gdb_string.h.
* posix-hdep.c: Use string.h, not gdb_string.h.
* ppc-linux-nat.c: Use string.h, not gdb_string.h.
* ppc-sysv-tdep.c: Use string.h, not gdb_string.h.
* ppcfbsd-tdep.c: Use string.h, not gdb_string.h.
* ppcnbsd-tdep.c: Use string.h, not gdb_string.h.
* ppcobsd-tdep.c: Use string.h, not gdb_string.h.
* printcmd.c: Use string.h, not gdb_string.h.
* procfs.c: Use string.h, not gdb_string.h.
* prologue-value.c: Use string.h, not gdb_string.h.
* python/py-auto-load.c: Use string.h, not gdb_string.h.
* python/py-gdb-readline.c: Use string.h, not gdb_string.h.
* ravenscar-thread.c: Use string.h, not gdb_string.h.
* regcache.c: Use string.h, not gdb_string.h.
* registry.c: Use string.h, not gdb_string.h.
* remote-fileio.c: Use string.h, not gdb_string.h.
* remote-m32r-sdi.c: Use string.h, not gdb_string.h.
* remote-mips.c: Use string.h, not gdb_string.h.
* remote-sim.c: Use string.h, not gdb_string.h.
* remote.c: Use string.h, not gdb_string.h.
* reverse.c: Use string.h, not gdb_string.h.
* rs6000-aix-tdep.c: Use string.h, not gdb_string.h.
* ser-base.c: Use string.h, not gdb_string.h.
* ser-go32.c: Use string.h, not gdb_string.h.
* ser-mingw.c: Use string.h, not gdb_string.h.
* ser-pipe.c: Use string.h, not gdb_string.h.
* ser-tcp.c: Use string.h, not gdb_string.h.
* ser-unix.c: Use string.h, not gdb_string.h.
* serial.c: Use string.h, not gdb_string.h.
* sh-tdep.c: Use string.h, not gdb_string.h.
* sh64-tdep.c: Use string.h, not gdb_string.h.
* shnbsd-tdep.c: Use string.h, not gdb_string.h.
* skip.c: Use string.h, not gdb_string.h.
* sol-thread.c: Use string.h, not gdb_string.h.
* solib-dsbt.c: Use string.h, not gdb_string.h.
* solib-frv.c: Use string.h, not gdb_string.h.
* solib-osf.c: Use string.h, not gdb_string.h.
* solib-spu.c: Use string.h, not gdb_string.h.
* solib-target.c: Use string.h, not gdb_string.h.
* solib.c: Use string.h, not gdb_string.h.
* somread.c: Use string.h, not gdb_string.h.
* source.c: Use string.h, not gdb_string.h.
* sparc-nat.c: Use string.h, not gdb_string.h.
* sparc-sol2-tdep.c: Use string.h, not gdb_string.h.
* sparc-tdep.c: Use string.h, not gdb_string.h.
* sparc64-tdep.c: Use string.h, not gdb_string.h.
* sparc64fbsd-tdep.c: Use string.h, not gdb_string.h.
* sparc64nbsd-tdep.c: Use string.h, not gdb_string.h.
* sparcnbsd-tdep.c: Use string.h, not gdb_string.h.
* spu-linux-nat.c: Use string.h, not gdb_string.h.
* spu-multiarch.c: Use string.h, not gdb_string.h.
* spu-tdep.c: Use string.h, not gdb_string.h.
* stabsread.c: Use string.h, not gdb_string.h.
* stack.c: Use string.h, not gdb_string.h.
* std-regs.c: Use string.h, not gdb_string.h.
* symfile.c: Use string.h, not gdb_string.h.
* symmisc.c: Use string.h, not gdb_string.h.
* symtab.c: Use string.h, not gdb_string.h.
* target.c: Use string.h, not gdb_string.h.
* thread.c: Use string.h, not gdb_string.h.
* tilegx-linux-nat.c: Use string.h, not gdb_string.h.
* tilegx-tdep.c: Use string.h, not gdb_string.h.
* top.c: Use string.h, not gdb_string.h.
* tracepoint.c: Use string.h, not gdb_string.h.
* tui/tui-command.c: Use string.h, not gdb_string.h.
* tui/tui-data.c: Use string.h, not gdb_string.h.
* tui/tui-disasm.c: Use string.h, not gdb_string.h.
* tui/tui-file.c: Use string.h, not gdb_string.h.
* tui/tui-layout.c: Use string.h, not gdb_string.h.
* tui/tui-out.c: Use string.h, not gdb_string.h.
* tui/tui-regs.c: Use string.h, not gdb_string.h.
* tui/tui-source.c: Use string.h, not gdb_string.h.
* tui/tui-stack.c: Use string.h, not gdb_string.h.
* tui/tui-win.c: Use string.h, not gdb_string.h.
* tui/tui-windata.c: Use string.h, not gdb_string.h.
* tui/tui-winsource.c: Use string.h, not gdb_string.h.
* typeprint.c: Use string.h, not gdb_string.h.
* ui-file.c: Use string.h, not gdb_string.h.
* ui-out.c: Use string.h, not gdb_string.h.
* user-regs.c: Use string.h, not gdb_string.h.
* utils.c: Use string.h, not gdb_string.h.
* v850-tdep.c: Use string.h, not gdb_string.h.
* valarith.c: Use string.h, not gdb_string.h.
* valops.c: Use string.h, not gdb_string.h.
* valprint.c: Use string.h, not gdb_string.h.
* value.c: Use string.h, not gdb_string.h.
* varobj.c: Use string.h, not gdb_string.h.
* vax-tdep.c: Use string.h, not gdb_string.h.
* vaxnbsd-tdep.c: Use string.h, not gdb_string.h.
* vaxobsd-tdep.c: Use string.h, not gdb_string.h.
* windows-nat.c: Use string.h, not gdb_string.h.
* xcoffread.c: Use string.h, not gdb_string.h.
* xml-support.c: Use string.h, not gdb_string.h.
* xstormy16-tdep.c: Use string.h, not gdb_string.h.
* xtensa-linux-nat.c: Use string.h, not gdb_string.h.
New command for removing symbol files added via
the add-symbol-file command.
2013-10-29 Nicolas Blanc <nicolas.blanc@intel.com>
* breakpoint.c (disable_breakpoints_in_freed_objfile): New function.
* objfiles.c (free_objfile): Notify free_objfile.
(is_addr_in_objfile): New function.
* objfiles.h (is_addr_in_objfile): New declaration.
* printcmd.c (clear_dangling_display_expressions): Act upon free_objfile
events instead of solib_unloaded events.
(_initialize_printcmd): Register observer for free_objfile instead
of solib_unloaded notifications.
* solib.c (remove_user_added_objfile): New function.
* symfile.c (remove_symbol_file_command): New command.
(_initialize_symfile): Add remove-symbol-file.
gdb/doc
* observer.texi: New free_objfile event.
Signed-off-by: Nicolas Blanc <nicolas.blanc@intel.com>
I tried debugging a remote Windows program on Linux host, and pointed the
sysroot to "/some/path/" rather than "remote:", and I found GDB couldn't
find the dlls in the sysroot. If the dll name is
"C:/Windows/system32/ntdll.dll", I end up with the sysroot+in_pathname
concatenated this way:
(top-gdb) p temp_pathname
$1 = 0x228b690 "/some/pathC:/Windows/system32/ntdll.dll"
^^
That is, a directory separator is missing. This is a regression.
The problem is that solib_find decides that since the target path has
a drive spec, a separator is not necessary, which is clearly wrong in
this case. That check was added in
<https://sourceware.org/ml/gdb-patches/2013-06/msg00028.html>, to
handle the case of sysroot being "remote:". This patch fixes that
original issue in a different way. Instead of checking whether the
path has a drive spec, check whether the sysroot is "remote:". The
patch adds a table that helps visualize the cases that need a
separator. I also confirmed the original issue is still handled as
expected. That is, that "set sysroot remote:" still does the right
thing.
remote_filename_p returns true if the filename is prefixed with
"remote:". In this case, we need to check whether the filename is
exactly "remote:". I thought of different ways or either changing
remote_filename_p or adding another convenience function to remote.c
to avoid exposing the "remote:" prefix out of remote.c. But all
attempts turned out adding lot of over needless complication. So the
patch just exposes the prefix behind a new macro, which allows using a
straighforward strcmp.
gdb/
2013-09-27 Pedro Alves <palves@redhat.com>
* remote.h (REMOTE_SYSROOT_PREFIX): New define.
(remote_filename_p): Add comment.
* remote.c (remote_filename_p): Adjust to use
REMOTE_SYSROOT_PREFIX.
* solib.c (solib_find): When deciding whether we need to add a
directory separator, check whether the sysroot is "remote:"
instead of checking whether the patch has a drive spec. Add
comments.
gdb/
2013-09-24 Jan Kratochvil <jan.kratochvil@redhat.com>
Pass down original filename for objfile.
* coffread.c (coff_symfile_read): Update symbol_file_add_separate call.
* elfread.c (elf_symfile_read): Likewise.
* jit.c (jit_object_close_impl): Update allocate_objfile call, no
longer set ORIGINAL_NAME.
(jit_bfd_try_read_symtab): Update symbol_file_add_from_bfd call.
* jv-lang.c (get_dynamics_objfile): Update allocate_objfile call.
* machoread.c (macho_add_oso_symfile): Add parameter name. Update
symbol_file_add_from_bfd call.
(macho_symfile_read_all_oso): Update two macho_add_oso_symfile calls.
(macho_check_dsym): Add parameter filenamep. Change function comment.
Set *filenamep.
(macho_symfile_read): New variable dsym_filename. Update
macho_check_dsym call. Use it for symbol_file_add_separate.
* objfiles.c (allocate_objfile): Add parameter name. New comment for
it. Use it for objfile->original_name.
(objfile_name): Return OBFD's filename, if available.
* objfiles.h (allocate_objfile): Add new parameter name.
* solib.c (solib_read_symbols): Update symbol_file_add_from_bfd call.
* symfile-mem.c (symbol_file_add_from_memory): Update
symbol_file_add_from_bfd call.
* symfile.c (read_symbols): Update symbol_file_add_separate call, new
comment for it.
(symbol_file_add_with_addrs): New parameter name, add function comment
for it. Remove variable name. Update allocate_objfile call.
(symbol_file_add_separate): New parameter name, add function comment
for it. Update symbol_file_add_with_addrs call.
(symbol_file_add_from_bfd): New parameter name. Update
symbol_file_add_with_addrs call.
(symbol_file_add): Update symbol_file_add_from_bfd call.
(reread_symbols): New variable original_name. Save
objfile->original_name by it.
* symfile.h (symbol_file_add_from_bfd, symbol_file_add_separate): Add
second parameter.
gdb/
2013-09-04 Jan Kratochvil <jan.kratochvil@redhat.com>
Code cleanup: Change OPF_DISABLE_REALPATH to OPF_RETURN_REALPATH.
* cli/cli-cmds.c (find_and_open_script): Add OPF_RETURN_REALPATH to
variable search_flags.
* defs.h (OPF_DISABLE_REALPATH): Rename to ...
(OPF_RETURN_REALPATH): ... here.
* dwarf2read.c (try_open_dwop_file): Set OPF_RETURN_REALPATH for flags.
* exec.c (exec_file_attach): Remove OPF_DISABLE_REALPATH from openp
call. Twice.
* nto-tdep.c (nto_find_and_open_solib): Add OPF_RETURN_REALPATH for
openp call.
* solib.c (solib_find): Likewise. Four times.
* source.c (openp): Change OPF_DISABLE_REALPATH to OPF_RETURN_REALPATH
in the function comment and for the realpath_fptr variable.
(source_full_path_of): Add OPF_RETURN_REALPATH for openp call.
(find_and_open_source): Likewise. Twice.
* symfile.c (symfile_bfd_open): Likewise, also twice.
* breakpoint.h (handle_solib_event): Moved function declaration
to solib.h.
* breakpoint.c (handle_solib_event): Moved function to solib.c.
(bpstat_stop_status): Pass new argument to handle_solib_event.
* solib.h (update_solib_breakpoints): New function declaration.
(handle_solib_event): Moved function declaration from
breakpoint.h.
* solib.c (update_solib_breakpoints): New function.
(handle_solib_event): Moved function from breakpoint.c.
Updated to call solib_ops->handle_event if not NULL.
* solist.h (target_so_ops): New fields "update_breakpoints" and
"handle_event".
* infrun.c (set_stop_on_solib_events): New function.
(_initialize_infrun): Use the above for "set
stop-on-solib-events".
(handle_inferior_event): Pass new argument to handle_solib_event.
* solib-svr4.c (probe.h): New include.
(svr4_free_library_list): New forward declaration.
(probe_action): New enum.
(probe_info): New struct.
(probe_info): New static variable.
(NUM_PROBES): New definition.
(svr4_info): New fields "using_xfer", "probes_table" and
"solib_list".
(free_probes_table): New function.
(free_solib_list): New function.
(svr4_pspace_data_cleanup): Free probes table and solib list.
(svr4_copy_library_list): New function.
(svr4_current_sos_via_xfer_libraries): New parameter "annex".
(svr4_read_so_list): New parameter "prev_lm".
(svr4_current_sos_direct): Renamed from "svr4_current_sos".
(svr4_current_sos): New function.
(probe_and_action): New struct.
(hash_probe_and_action): New function.
(equal_probe_and_action): Likewise.
(register_solib_event_probe): Likewise.
(solib_event_probe_at): Likewise.
(solib_event_probe_action): Likewise.
(solist_update_full): Likewise.
(solist_update_incremental): Likewise.
(disable_probes_interface_cleanup): Likewise.
(svr4_handle_solib_event): Likewise.
(svr4_update_solib_event_breakpoint): Likewise.
(svr4_update_solib_event_breakpoints): Likewise.
(svr4_create_solib_event_breakpoints): Likewise.
(enable_break): Free probes table before creating breakpoints.
Use svr4_create_solib_event_breakpoints to create breakpoints.
(svr4_solib_create_inferior_hook): Free the solib list.
(_initialize_svr4_solib): Initialise
svr4_so_ops.handle_solib_event and svr4_so_ops.update_breakpoints.
Code cleanup: constification.
* solib.c (solib_ops): Make return type and ops variable type const.
(set_solib_ops): Make the new_ops parameter and ops variable const.
(solib_find, solib_map_sections, clear_so, free_so, update_solib_list)
(solib_add, solib_keep_data_in_core, clear_solib)
(solib_create_inferior_hook, in_solib_dynsym_resolve_code)
(reload_shared_libraries, solib_global_lookup): Make the ops variable
const.
* solib.h (set_solib_ops): Make the new_ops parameter const.
* solib-svr4.c (svr4_clear_so): New function.
(_initialize_svr4_solib): Set svr4_so_ops.clear_so.
* solib.c (clear_so): Renamed from free_so_symbols.
All callers updated. Call target clear_so if it exists.
Two modifications:
1. The addition of 2013 to the copyright year range for every file;
2. The use of a single year range, instead of potentially multiple
year ranges, as approved by the FSF.
and 'abfd'.
* elfread.c (elf_symfile_read): Make a cleanup for 'debugfile'
and 'abfd'.
* jit.c (jit_bfd_try_read_symtab): Make a cleanup for 'nbfd'.
* machoread.c (macho_add_oso_symfile): Make a cleanup for
'abfd'.
(macho_symfile_read): Make a cleanup for 'dsym_bfd'.
* objfiles.c (allocate_objfile): Acquire a new reference.
* rs6000-nat.c (add_vmap): Don't acquire a BFD reference.
* solib.c (solib_read_symbols): Don't acquire a BFD reference.
* spu-linux-nat.c (spu_symbol_file_add_from_memory): Make
a cleanup for 'nbfd'.
* symfile-mem.c (symbol_file_add_from_memory): Make a cleanup
for 'nbfd'.
* symfile.c (symbol_file_add_with_addrs_or_offsets): Don't
make a cleanup for 'abfd'.
(symbol_file_add): Make a BFD cleanup.
gdb_bfd_unref.
(free_dwo_file): Use gdb_bfd_unref.
* cli/cli-dump.c: Include gdb_bfd.h.
(bfd_openw_with_cleanup): Use gdb_bfd_ref.
(bfd_openr_with_cleanup): Likewise.
* windows-nat.c (windows_make_so): Use gdb_bfd_ref,
gdb_bfd_unref.
* utils.c: Include gdb_bfd.h.
(do_bfd_close_cleanup): Use gdb_bfd_unref.
* symfile.c: Include gdb_bfd.h.
(separate_debug_file_exists): Use gdb_bfd_unref.
(bfd_open_maybe_remote): Use gdb_bfd_ref.
(symfile_bfd_open): Use gdb_bfd_ref, gdb_bfd_unref.
(generic_load): Use gdb_bfd_ref.
(reread_symbols): Use gdb_bfd_unref.
* symfile-mem.c: Include gdb_bfd.h.
(symbol_file_add_from_memory): Use make_cleanup_bfd_close.
* spu-linux-nat.c (spu_bfd_open): Use gdb_bfd_ref, gdb_bfd_unref.
* solib.c: Include gdb_bfd.h.
(solib_bfd_fopen): Use gdb_bfd_ref.
(solib_bfd_open): Use gdb_bfd_unref.
(free_so_symbols): Use gdb_bfd_unref.
(reload_shared_libraries_1): Use gdb_bfd_unref.
* solib-spu.c: Include gdb_bfd.h.
(spu_bfd_fopen): Use gdb_bfd_ref, gdb_bfd_unref.
* solib-pa64.c (pa64_solib_create_inferior_hook): Use gdb_bfd_ref,
gdb_bfd_unref.
* solib-frv.c: Include gdb_bfd.h.
(enable_break2): Use gdb_bfd_unref.
* solib-dsbt.c: Include gdb_bfd.h.
(enable_break2): Use gdb_bfd_unref.
* solib-darwin.c: Include gdb_bfd.h.
(darwin_solib_get_all_image_info_addr_at_init): Use gdb_bfd_ref,
gdb_bfd_unref.
(darwin_bfd_open): Use gdb_bfd_unref.
* rs6000-nat.c (add_vmap): Use gdb_bfd_ref, gdb_bfd_unref.
* remote-mips.c: Include gdb_bfd.h.
(mips_load_srec): Use gdb_bfd_ref.
(pmon_load_fast): Use gdb_bfd_ref.
* remote-m32r-sdi.c: Include gdb_bfd.h.
(m32r_load): Use gdb_bfd_ref.
* record.c: Include gdb_bfd.h.
(record_save_cleanups): Use gdb_bfd_unref.
(cmd_record_save): Use gdb_bfd_unref.
* procfs.c (insert_dbx_link_bpt_in_file): Use gdb_bfd_ref,
gdb_bfd_unref.
* objfiles.h (gdb_bfd_close_or_warn): Remove.
(gdb_bfd_ref, gdb_bfd_unref): Move to gdb_bfd.h.
* objfiles.c: Include gdb_bfd.h.
(free_objfile): Use gdb_bfd_unref.
(gdb_bfd_close_or_warn, gdb_bfd_ref, gdb_bfd_unref): Move to
gdb_bfd.c.
* machoread.c (macho_add_oso_symfile): Use gdb_bfd_unref.
(macho_symfile_read_all_oso): Use gdb_bfd_ref, gdb_bfd_unref.
(macho_check_dsym): Likewise.
* m32r-rom.c: Include gdb_bfd.h.
(m32r_load): Use gdb_bfd_ref.
(m32r_upload_command): Use gdb_bfd_ref.
* jit.c: Include gdb_bfd.h.
(jit_bfd_try_read_symtab): Use gdb_bfd_ref, gdb_bfd_unref.
* gdb_bfd.h: New file.
* gdb_bfd.c: New file.
* gcore.c: Include gdb_bfd.h.
(create_gcore_bfd): Use gdb_bfd_ref.
(do_bfd_delete_cleanup): Use gdb_bfd_unref.
(gcore_command): Use gdb_bfd_unref.
* exec.c: Include gdb_bfd.h.
(exec_close): Use gdb_bfd_unref.
(exec_close_1): Use gdb_bfd_unref.
(exec_file_attach): Use gdb_bfd_ref.
* elfread.c: Include gdb_bfd.h.
(build_id_verify): Use gdb_bfd_unref.
* dsrec.c: Include gdb_bfd.h.
(load_srec): Use gdb_bfd_ref.
* corelow.c: Include gdb_bfd.h.
(core_close): Use gdb_bfd_unref.
(core_open): Use gdb_bfd_ref.
* bfd-target.c: Include gdb_bfd.h.
(target_bfd_xclose): Use gdb_bfd_unref.
(target_bfd_reopen): Use gdb_bfd_ref.
* Makefile.in (SFILES): Add gdb_bfd.c.
(HFILES_NO_SRCDIR): Add gdb_bfd.h.
(COMMON_OBS): Add gdb_bfd.o.
* opncls.c (bfd_fopen): Always close fd on failure.
(bfd_fdopenr): Likewise.
gdb/
* symfile.c (symfile_bfd_open): Don't close desc if bfd_fopen
fails.
* solib.c (solib_bfd_fopen): Don't close fd if bfd_fopen fails.
* exec.c (exec_file_attach): Don't close scratch_chan if bfd_fopen
fails.
* dwarf2read.c (try_open_dwo_file): Don't close fd if bfd_fopen
fails.
symfile_flags.
* solib.c (solib_read_symbols): Use inferior's symfile_flags.
* linux-nat.c (linux_child_follow_fork): Set symfile_flags on
inferior.
* infrun.c (handle_vfork_child_exec_or_exit): Set symfile_flags on
inferior.
(follow_exec): Use inferior's symfile_flags.
* inferior.h (struct inferior) <symfile_flags>: New field.
* solib.c (update_solib_list): Update the program space's
added_solibs and deleted_solibs fields.
* progspace.h (struct program_space) <added_solibs,
deleted_solibs>: New fields.
(clear_program_space_solib_cache): Declare.
* progspace.c (release_program_space): Call
clear_program_space_solib_cache.
(clear_program_space_solib_cache): New function.
* infrun.c (handle_inferior_event) <TARGET_WAITKIND_LOADED>: Call
bpstat_stop_status. Use handle_solib_event.
* breakpoint.c: Include gdb_regex.h.
(print_solib_event): New function.
(bpstat_print): Use print_solib_event.
(bpstat_stop_status): Add special case for bp_shlib_event.
(handle_solib_event): New function.
(bpstat_what): Use handle_solib_event.
(struct solib_catchpoint): New.
(dtor_catch_solib, insert_catch_solib, remove_catch_solib)
(breakpoint_hit_catch_solib, check_status_catch_solib)
(print_it_catch_solib, print_one_catch_solib)
(print_mention_catch_solib, print_recreate_catch_solib): New
functions.
(catch_solib_breakpoint_ops): New global.
(catch_load_or_unload, catch_load_command_1)
(catch_unload_command_1): New functions.
(internal_bkpt_check_status): Add special case for
bp_shlib_event.
(internal_bkpt_print_it): Use print_solib_event.
(initialize_breakpoint_ops): Initialize
catch_solib_breakpoint_ops.
(_initialize_breakpoint): Register "catch load" and "catch
unload".
* breakpoint.h (handle_solib_event): Declare.
* NEWS: Add entry for "catch load" and "catch unload".
gdb/doc
* gdb.texinfo (Set Catchpoints): Document "catch load" and "catch
unload".
(Files): Mention new catch commands.
(GDB/MI Async Records): Likewise.
gdb/testsuite
* lib/mi-support.exp (mi_expect_stop): Add special case for
solib-event.
* gdb.base/catch-load-so.c: New file.
* gdb.base/catch-load.exp: New file.
* gdb.base/catch-load.c: New file.
* gdb.base/break-interp.exp (reach_1): Update regexp.
* elf64-ppc.c (ppc64_elf_get_synthetic_symtab): Do not check for
SEC_LOAD.
gdb/
Fix convert_code_addr_to_desc_addr for ppc64 files after eu-strip.
* elfread.c (elf_symfile_read): New variable synth_abfd, pass it to
bfd_get_synthetic_symtab.
* jit.c (jit_register_code): Pass NULL to the new parameter parent.
* machoread.c (macho_add_oso_symfile): Pass main_objfile to the new
parameter parent, remove the call to add_separate_debug_objfile.
* solib.c (solib_read_symbols): Pass NULL to the new parameter parent.
* symfile-mem.c (symbol_file_add_from_memory): Likewise.
* symfile.c (symbol_file_add_with_addrs_or_offsets): New parameter
parent, new comment for it, call add_separate_debug_objfile for it.
(symbol_file_add_separate): Pass objfile as the parameter parent,
remove the call to add_separate_debug_objfile.
(symbol_file_add_from_bfd): New parameter parent, pass it.
(symbol_file_add): Pass NULL to the new parameter parent.
* symfile.h (symbol_file_add_from_bfd): New parameter parent.
gdb/testsuite/
* gdb.base/eu-strip-infcall.c: New file.
* gdb.base/eu-strip-infcall.exp: New file.
PR/symtab 11766:
* gdb/objfiles.h (struct objfile) <addr_low>: New field.
* gdb/solib.c (solib_read_symbols): Check for addr_low in
equality test for objfile, initialize addr_low if needed.
Joel Brobecker
Maciej W. Rozycki
Jan Kratochvil
Doug Evans
Gary Benson
Doug Evans
Tom Tromey
Nicolas Blanc
Pedro Alves
Gary Benson
Yao Qi
Joel Brobecker
Edjunior Barbosa Machado
Aleksandar Ristovski
Paul Pluzhnikov
Kai Tietz
Michael Snyder
Thiago Jung Bauermann