gdb/ChangeLog:
* nat/linux-nat.h (__SIGRTMIN): Move here from gdbserver/linux-low.c.
gdb/gdbserver/ChangeLog:
* linux-low.c (__SIGRTMIN): Move to nat/linux-nat.h.
Nowadays, both aarch64 GDB and linux kernel assumes that address for
setting breakpoint should be 4-byte aligned. However that is not true
after we support multi-arch, because thumb instruction can be at 2-byte
aligned address. Patch http://lists.infradead.org/pipermail/linux-arm-kernel/2015-October/375141.html
to linux kernel is to teach kernel to handle 2-byte aligned address for
HW breakpoint, while this patch is to teach aarch64 GDB handle 2-byte
aligned address.
First of all, we call gdbarch_breakpoint_from_pc to get the instruction
length rather than using hard-coded 4. Secondly, in GDBserver, we set
length back to 2 if it is 3, because GDB encode 3 in it to indicate it
is a 32-bit thumb breakpoint. Then we relax the address alignment
check from 4-byte aligned to 2-byte aligned.
This patch enables some tests (such as gdb.base/break-idempotent.exp,
gdb.base/cond-eval-mode.exp, gdb.base/watchpoint-reuse-slot.exp,) and
fixes many fails (such as gdb.base/hbreak2.exp) when the program is
compiled in thumb mode on aarch64.
Regression tested on aarch64-linux, both native and gdbserver. This
is the last patch of multi-arch work.
gdb:
2015-10-15 Yao Qi <yao.qi@linaro.org>
* aarch64-linux-nat.c (aarch64_linux_insert_hw_breakpoint):
Call gdbarch_breakpoint_from_pc to instruction length.
(aarch64_linux_remove_hw_breakpoint): Likewise.
* common/common-regcache.h (regcache_register_size): Declare.
* nat/aarch64-linux-hw-point.c: Include "common-regcache.h".
(aarch64_point_is_aligned): Set alignment to 2 for breakpoint if
the process is 32bit, otherwise set alignment to 4.
(aarch64_handle_breakpoint): Update comments.
* regcache.c (regcache_register_size): New function.
gdb/gdbserver:
2015-10-15 Yao Qi <yao.qi@linaro.org>
* linux-aarch64-low.c (aarch64_insert_point): Set len to 2
if it is 3.
(aarch64_remove_point): Likewise.
* regcache.c (regcache_register_size): New function.
With the kernle fix <http://lists.infradead.org/pipermail/linux-arm-kernel/2015-July/356511.html>,
aarch64 GDB is able to read the base of thread area of 32-bit arm
program through NT_ARM_TLS.
This patch is to teach both GDB and GDBserver to read the base of
thread area correctly in the multi-arch case. A new function
aarch64_ps_get_thread_area is added, and is shared between GDB and
GDBserver.
With this patch applied, the following fails in multi-arch testing
(GDB is aarch64 but the test cases are arm) are fixed,
-FAIL: gdb.threads/tls-nodebug.exp: thread local storage
-FAIL: gdb.threads/tls-shared.exp: print thread local storage variable
-FAIL: gdb.threads/tls-so_extern.exp: print thread local storage variable
-FAIL: gdb.threads/tls-var.exp: print tls_var
-FAIL: gdb.threads/tls.exp: first thread local storage
-FAIL: gdb.threads/tls.exp: first another thread local storage
-FAIL: gdb.threads/tls.exp: p a_thread_local
-FAIL: gdb.threads/tls.exp: p file2_thread_local
-FAIL: gdb.threads/tls.exp: p a_thread_local second time
gdb:
2015-09-18 Yao Qi <yao.qi@linaro.org>
* nat/aarch64-linux.c: Include elf/common.h,
nat/gdb_ptrace.h, asm/ptrace.h and sys/uio.h.
(aarch64_ps_get_thread_area): New function.
* nat/aarch64-linux.h: Include gdb_proc_service.h.
(aarch64_ps_get_thread_area): Declare.
* aarch64-linux-nat.c (ps_get_thread_area): Call
aarch64_ps_get_thread_area.
gdb/gdbserver:
2015-09-18 Yao Qi <yao.qi@linaro.org>
* linux-aarch64-low.c: Don't include sys/uio.h.
(ps_get_thread_area): Call aarch64_ps_get_thread_area.
This patch is to fixup the siginfo_t when aarch64 gdb or gdbserver
read from or write to the arm inferior. It is to convert the
"struct siginfo_t" between aarch64 and arm, which is quite mechanical.
gdb/gdbserver:
2015-09-15 Yao Qi <yao.qi@linaro.org>
* linux-aarch64-low.c (aarch64_linux_siginfo_fixup): New
function.
(struct linux_target_ops the_low_target): Install
aarch64_linux_siginfo_fixup.
gdb:
2015-09-15 Yao Qi <yao.qi@linaro.org>
* aarch64-linux-nat.c (aarch64_linux_siginfo_fixup): New function.
(_initialize_aarch64_linux_nat): Call linux_nat_set_siginfo_fixup.
* nat/aarch64-linux.c (aarch64_compat_siginfo_from_siginfo):
New function.
(aarch64_siginfo_from_compat_siginfo): New function.
* nat/aarch64-linux.h: Include signal.h.
(compat_int_t, compat_uptr_t, compat_time_t): Typedef.
(compat_timer_t, compat_clock_t): Likewise.
(struct compat_timeval): New.
(union compat_sigval): New.
(struct compat_siginfo): New.
(cpt_si_pid, cpt_si_uid, cpt_si_timerid): New macros.
(cpt_si_overrun, cpt_si_status, cpt_si_utime): Likewise.
(cpt_si_stime, cpt_si_ptr, cpt_si_addr): Likewise.
(cpt_si_band, cpt_si_fd): Likewise.
This patch implements support for exec events on extended-remote Linux
targets. Follow-exec-mode and rerun behave as expected. Catchpoints and
test updates are implemented in subsequent patches.
This patch was derived from a patch posted last October:
https://sourceware.org/ml/gdb-patches/2014-10/msg00877.html.
It was originally based on some work done by Luis Machado in 2013.
IMPLEMENTATION
----------------
Exec events are enabled via ptrace options.
When an exec event is detected by gdbserver, the existing process
data, along with all its associated lwp and thread data, is deleted
and replaced by data for a new single-threaded process. The new
process data is initialized with the appropriate parts of the state
of the execing process. This approach takes care of several potential
pitfalls, including:
* deleting the data for an execing non-leader thread before any
wait/sigsuspend occurs
* correctly initializing the architecture of the execed process
We then report the exec event using a new RSP stop reason, "exec".
When GDB receives an "exec" event, it saves the status in the event
structure's target_waitstatus field, like what is done for remote fork
events. Because the original and execed programs may have different
architectures, we skip parsing the section of the stop reply packet
that contains register data. The register data will be retrieved
later after the inferior's architecture has been set up by
infrun.c:follow_exec.
At that point the exec event is handled by the existing event handling
in GDB. However, a few changes were necessary so that
infrun.c:follow_exec could accommodate the remote target.
* Where follow-exec-mode "new" is handled, we now call
add_inferior_with_spaces instead of add_inferior with separate calls
to set up the program and address spaces. The motivation for this
is that add_inferior_with_spaces also sets up the initial architecture
for the inferior, which is needed later by target_find_description
when it calls target_gdbarch.
* We call a new target function, target_follow_exec. This function
allows us to store the execd_pathname in the inferior, instead of
using the static string remote_exec_file from remote.c. The static
string didn't work for follow-exec-mode "new", since once you switched
to the execed program, the original remote exec-file was lost. The
execd_pathname is now stored in the inferior's program space as a
REGISTRY field. All of the requisite mechanisms for this are
defined in remote.c.
gdb/gdbserver/ChangeLog:
* linux-low.c (linux_mourn): Static declaration.
(linux_arch_setup): Move in front of
handle_extended_wait.
(linux_arch_setup_thread): New function.
(handle_extended_wait): Handle exec events. Call
linux_arch_setup_thread. Make event_lwp argument a
pointer-to-a-pointer.
(check_zombie_leaders): Do not check stopped threads.
(linux_low_ptrace_options): Add PTRACE_O_TRACEEXEC.
(linux_low_filter_event): Add lwp and thread for exec'ing
non-leader thread if leader thread has been deleted.
Refactor code into linux_arch_setup_thread and call it.
Pass child lwp pointer by reference to handle_extended_wait.
(linux_wait_for_event_filtered): Update comment.
(linux_wait_1): Prevent clobbering exec event status.
(linux_supports_exec_events): New function.
(linux_target_ops) <supports_exec_events>: Initialize new member.
* lynx-low.c (lynx_target_ops) <supports_exec_events>: Initialize
new member.
* remote-utils.c (prepare_resume_reply): New stop reason 'exec'.
* server.c (report_exec_events): New global variable.
(handle_query): Handle qSupported query for exec-events feature.
(captured_main): Initialize report_exec_events.
* server.h (report_exec_events): Declare new global variable.
* target.h (struct target_ops) <supports_exec_events>: New
member.
(target_supports_exec_events): New macro.
* win32-low.c (win32_target_ops) <supports_exec_events>:
Initialize new member.
gdb/ChangeLog:
* infrun.c (follow_exec): Use process-style ptid for
exec message. Call add_inferior_with_spaces and
target_follow_exec.
* nat/linux-ptrace.c (linux_supports_traceexec): New function.
* nat/linux-ptrace.h (linux_supports_traceexec): Declare.
* remote.c (remote_pspace_data): New static variable.
(remote_pspace_data_cleanup): New function.
(get_remote_exec_file): New function.
(set_remote_exec_file_1): New function.
(set_remote_exec_file): New function.
(show_remote_exec_file): New function.
(remote_exec_file): Delete static variable.
(anonymous enum) <PACKET_exec_event_feature> New
enumeration constant.
(remote_protocol_features): Add entry for exec-events feature.
(remote_query_supported): Add client side of qSupported query
for exec-events feature.
(remote_follow_exec): New function.
(remote_parse_stop_reply): Handle 'exec' stop reason.
(extended_remote_run, extended_remote_create_inferior): Call
get_remote_exec_file and set_remote_exec_file_1.
(init_extended_remote_ops) <to_follow_exec>: Initialize new
member.
(_initialize_remote): Call
register_program_space_data_with_cleanup. Call
add_packet_config_cmd for remote exec-events feature.
Modify call to add_setshow_string_noescape_cmd for exec-file
to use new functions set_remote_exec_file and
show_remote_exec_file.
* target-debug.h, target-delegates.c: Regenerated.
* target.c (target_follow_exec): New function.
* target.h (struct target_ops) <to_follow_exec>: New member.
(target_follow_exec): Declare new function.
For the BTS recording format, we sometimes get a FROM->TO record where the
FROM address lies in the kernel and the TO address lies in user space at
whatever address the user process was resumed.
GDB has a heuristic to filter out such records based on looking at the most
significant bit in the PC. This works fine for 64-bit systems but it doesn't
always work for 32-bit systems. Libraries that are loaded at fairly high
addresses might be mistaken for kernel code and branches inside the library
are filtered out.
Change the heuristic to (again heuristically) try to determine the lowest
address in kernel space. Any PC that is smaller than that should be in
user space.
On today's systems, there should be a symbol "_text" at that address.
Read /proc/kallsyms and search for that symbol.
It is not guaranteed that /proc/kallsyms is readable on all systems. On
64-bit systems, we fall back to check the most significant bit. On 32-bit
systems, we refrain from filtering out addresses.
The filtering should really be done by the kernel. And it soon will be:
https://lkml.org/lkml/2015/8/31/212.
gdb/
* nat/linux-btrace.h (struct btrace_target_info) <ptr_bits>: Remove.
* nat/linux-btrace.c: Include filestuff.h and inttypes.h.
Remove include of sys/utsname.h.
(linux_determine_kernel_ptr_bits): Remove.
(linux_determine_kernel_start): New.
(perf_event_is_kernel_addr): Remove tinfo argument. Update users.
Update check.
(perf_event_skip_bts_record): Remove tinfo argument. Update users.
(linux_enable_bts, linux_enable_pt): Remove tinfo->ptr_bits
initialization.
* x86-linux-nat.c (x86_linux_enable_btrace): Remove ptr_bits
assignment.
gdbserver/
* linux-low.c (linux_low_enable_btrace): Remove.
(linux_target_ops): Replace linux_low_enable_btrace with
linux_enable_btrace.
Nowadays, if user requests HW watchpoint to monitor a large memory area
or unaligned area, aarch64 GDB will split into multiple aligned areas,
and use multiple debugging registers to watch them. However, the
registers are not updated in a transaction way. GDBserver doesn't revert
updates in previous iterations if some debugging registers fail to update
due to some reason, like no free debugging registers available, in the
latter iteration. For example, if we have a char buf[34], and watch buf
in gdb,
(gdb) watch buf
Hardware watchpoint 2: buf
(gdb) c
Continuing.
infrun: clear_proceed_status_thread (Thread 13466)
infrun: proceed (addr=0xffffffffffffffff, signal=GDB_SIGNAL_DEFAULT)
infrun: step-over queue now empty
infrun: resuming [Thread 13466] for step-over
Sending packet: $m410838,22#35...Packet received: 00000000000000000000000000000000000000000000000000000000000000000000
infrun: skipping breakpoint: stepping past insn at: 0x400524
infrun: skipping breakpoint: stepping past insn at: 0x400524
Sending packet: $Z2,410838,22#80...Packet received: E01 <----- [1]
Packet Z2 (write-watchpoint) is supported
Sending packet: $Z0,7fb7fe0a8c,4#43...Packet received: OK
Warning:
Could not insert hardware watchpoint 2.
Could not insert hardware breakpoints:
You may have requested too many hardware breakpoints/watchpoints.
GDB receives E01 for Z2 packet [1] but GDBserver updates the debugging
register status,
insert_point (addr=0x00410838, len=34, type=hw-write-watchpoint):
BREAKPOINTs:
BP0: addr=0x0, ctrl=0x00000000, ref.count=0
BP1: addr=0x0, ctrl=0x00000000, ref.count=0
BP2: addr=0x0, ctrl=0x00000000, ref.count=0
BP3: addr=0x0, ctrl=0x00000000, ref.count=0
BP4: addr=0x0, ctrl=0x00000000, ref.count=0
BP5: addr=0x0, ctrl=0x00000000, ref.count=0
WATCHPOINTs:
WP0: addr=0x410850, ctrl=0x00001ff5, ref.count=1
WP1: addr=0x410848, ctrl=0x00001ff5, ref.count=1
WP2: addr=0x410840, ctrl=0x00001ff5, ref.count=1
WP3: addr=0x410838, ctrl=0x00001ff5, ref.count=1
four debugging registers can not monitor 34-byte long area, so the last
iteration of updating debugging register state fails but previous
iterations succeed. This makes GDB think no HW watchpoint is inserted
but some debugging registers are used.
This problem was exposed by "watch buf" gdb.base/watchpoint.exp with
aarch64 GDBserver debugging arm 32-bit program. The buf is 30-byte long
but 4-byte aligned, and four debugging registers can't cover 34-byte
(extend 4 bytes to be 8-byte aligned) area. However, this problem
does exist on non-multi-arch debugging scenario as well.
This patch moves code in aarch64_linux_region_ok_for_hw_watchpoint to
aarch64_linux_region_ok_for_watchpoint in nat/aarch64-linux-hw-point.c.
Then, checks with aarch64_linux_region_ok_for_watchpoint, like what we
are doing in GDB. If the region is OK, call aarch64_handle_watchpoint.
Regression tested on aarch64 with both 64-bit program and 32-bit
program. Some fails in gdb.base/watchpoint.exp are fixed.
gdb:
2015-09-03 Yao Qi <yao.qi@linaro.org>
* aarch64-linux-nat.c (aarch64_linux_region_ok_for_hw_watchpoint):
Move code to aarch64_linux_region_ok_for_watchpoint. Call
aarch64_linux_region_ok_for_watchpoint.
* nat/aarch64-linux-hw-point.c (aarch64_linux_region_ok_for_watchpoint):
New function.
* nat/aarch64-linux-hw-point.h (aarch64_linux_region_ok_for_watchpoint):
Declare it.
gdb/gdbserver:
2015-09-03 Yao Qi <yao.qi@linaro.org>
* linux-aarch64-low.c (aarch64_insert_point): Call
aarch64_handle_watchpoint if aarch64_linux_region_ok_for_watchpoint
returns true.
The Linux target and gdbserver now check the siginfo si_code
reported on a SIGTRAP to detect whether the trap indicates
a software breakpoint was hit.
Unfortunately, on Cell/B.E., the kernel uses an si_code value
of TRAP_BRKPT when a SW breakpoint was hit in PowerPC code,
but a si_code value of SI_KERNEL when a SW breakpoint was
hit in SPU code.
This patch updates Linux target and gdbserver to accept both
si_code values to indicate SW breakpoint on PowerPC.
ChangeLog:
* nat/linux-ptrace.h (GDB_ARCH_TRAP_BRKPT): Replace by ...
(GDB_ARCH_IS_TRAP_BRKPT): ... this. Add __powerpc__ case.
* linux-nat.c (check_stopped_by_breakpoint): Use
GDB_ARCH_IS_TRAP_BRKPT instead of GDB_ARCH_TRAP_BRKPT.
gdbserver/ChangeLog:
* linux-low.c (check_stopped_by_breakpoint): Use
GDB_ARCH_IS_TRAP_BRKPT instead of GDB_ARCH_TRAP_BRKPT.
In debug_reg_change_callback, we change debug registers of each LWP.
It makes more sense to print LWP's pid rather than group leader's pid.
gdb:
2015-08-25 Yao Qi <yao.qi@linaro.org>
* nat/aarch64-linux-hw-point.c (debug_reg_change_callback):
Rename local variable pid to tid, and get lwpid of lwp. Update
debug output.
This patch moves aarch64_linux_new_thread in GDB and GDBserver to
nat/aarch64-linux.c.
gdb:
2015-08-25 Yao Qi <yao.qi@linaro.org>
* aarch64-linux-nat.c (aarch64_linux_new_thread): Move it to ...
* nat/aarch64-linux.c (aarch64_linux_new_thread): ... here.
* nat/aarch64-linux.h (aarch64_linux_new_thread): Declare.
gdb/gdbserver:
2015-08-25 Yao Qi <yao.qi@linaro.org>
* linux-aarch64-low.c (aarch64_linux_new_thread): Remove.
This commit fixes a stale cleanup left by linux_mntns_access_fs.
gdb/ChangeLog:
* nat/linux-namespaces.c (linux_mntns_access_fs):
Do not overwrite old_chain.
Running gdbserver --debug under Valgrind shows:
==4803== Invalid read of size 4
==4803== at 0x432B62: linux_write_memory (linux-low.c:5320)
==4803== by 0x4143F7: write_inferior_memory (target.c:83)
==4803== by 0x415895: remove_memory_breakpoint (mem-break.c:362)
==4803== by 0x432EF5: linux_remove_point (linux-low.c:5460)
==4803== by 0x416319: delete_raw_breakpoint (mem-break.c:802)
==4803== by 0x4163F3: release_breakpoint (mem-break.c:842)
==4803== by 0x416477: delete_breakpoint_1 (mem-break.c:869)
==4803== by 0x4164EF: delete_breakpoint (mem-break.c:891)
==4803== by 0x416843: delete_gdb_breakpoint_1 (mem-break.c:1069)
==4803== by 0x4168D8: delete_gdb_breakpoint (mem-break.c:1098)
==4803== by 0x4134E3: process_serial_event (server.c:4051)
==4803== by 0x4138E4: handle_serial_event (server.c:4196)
==4803== Address 0x4c6b930 is 0 bytes inside a block of size 1 alloc'd
==4803== at 0x4A0645D: malloc (in /usr/lib64/valgrind/vgpreload_memcheck-amd64-linux.so)
==4803== by 0x4240C6: xmalloc (common-utils.c:43)
==4803== by 0x41439C: write_inferior_memory (target.c:80)
==4803== by 0x415895: remove_memory_breakpoint (mem-break.c:362)
==4803== by 0x432EF5: linux_remove_point (linux-low.c:5460)
==4803== by 0x416319: delete_raw_breakpoint (mem-break.c:802)
==4803== by 0x4163F3: release_breakpoint (mem-break.c:842)
==4803== by 0x416477: delete_breakpoint_1 (mem-break.c:869)
==4803== by 0x4164EF: delete_breakpoint (mem-break.c:891)
==4803== by 0x416843: delete_gdb_breakpoint_1 (mem-break.c:1069)
==4803== by 0x4168D8: delete_gdb_breakpoint (mem-break.c:1098)
==4803== by 0x4134E3: process_serial_event (server.c:4051)
==4803==
And:
==7272== Conditional jump or move depends on uninitialised value(s)
==7272== at 0x3615E48361: vfprintf (vfprintf.c:1634)
==7272== by 0x414E89: debug_vprintf (debug.c:60)
==7272== by 0x42800A: debug_printf (common-debug.c:35)
==7272== by 0x43937B: my_waitpid (linux-waitpid.c:149)
==7272== by 0x42D740: linux_wait_for_event_filtered (linux-low.c:2441)
==7272== by 0x42DADA: linux_wait_for_event (linux-low.c:2552)
==7272== by 0x42E165: linux_wait_1 (linux-low.c:2860)
==7272== by 0x42F5D8: linux_wait (linux-low.c:3453)
==7272== by 0x4144A4: mywait (target.c:107)
==7272== by 0x413969: handle_target_event (server.c:4214)
==7272== by 0x41A1A6: handle_file_event (event-loop.c:429)
==7272== by 0x41996D: process_event (event-loop.c:184)
gdb/ChangeLog:
2015-08-06 Pedro Alves <palves@redhat.com>
* nat/linux-waitpid.c (my_waitpid): Only print *status if waitpid
returned > 0.
gdb/gdbserver/ChangeLog:
2015-08-06 Pedro Alves <palves@redhat.com>
* linux-low.c (linux_write_memory): Rewrite debug output to avoid
reading beyond the passed in buffer length.
Fixes a build error due to typedef redefinition with some compilers.
Also added missing copyright header.
gdb/
* nat/gdb_thread_db.h: Add copyright header.
Protect against multiple inclusion.
Implicit void * -> function pointer conversion doesn't work in C++, so
in C++, we need to cast the result of dlsym. This adds a few typedefs
and macros that make this easy. GDBserver's version already had the
CHK macro, so I added it to GDB too.
Tested on x86_64 Fedora 20, native and gdbserver.
gdb/gdbserver/ChangeLog:
2015-08-04 Pedro Alves <palves@redhat.com>
* thread-db.c (struct thread_db): Use new typedefs.
(try_thread_db_load_1): Define local TDB_DLSYM macro and use it in
CHK calls.
(disable_thread_event_reporting): Cast result of dlsym to
destination function pointer type.
(thread_db_mourn): Use td_ta_delete_ftype.
gdb/ChangeLog:
2015-08-04 Pedro Alves <palves@redhat.com>
* nat/gdb_thread_db.h (td_init_ftype, td_ta_new_ftype)
(td_ta_map_lwp2thr_ftype, td_ta_thr_iter_ftype)
(td_ta_event_addr_ftype, td_ta_set_event_ftype)
(td_ta_clear_event_ftype, td_ta_event_getmsg_ftype)
(td_thr_validate_ftype, td_thr_get_info_ftype)
(td_thr_event_enable_ftype, td_thr_tls_get_addr_ftype)
(td_thr_tlsbase_ftype, td_symbol_list_ftype, td_ta_delete_ftype):
New typedefs.
* linux-thread-db.c (struct thread_db_info): Use new typedefs.
(try_thread_db_load_1): Define TDB_VERBOSE_DLSYM, TDB_DLSYM , CHK
local macros and use them instead of verbose_dlsym and dlsym
calls.
Since Pedro's ptrace cleanups, the MIPS buildbot compilation fails.
Code in MIPS native uses ptrace with 3 arguments, where ptrace requires
4. When looking at the definition of ptrace in
/usr/include/sys/ptrace.h, it shows that it takes a variable number of
arguments. The wrapper macro in nat/gdb_ptrace.h takes a fixed number
of arguments (4). That would explain why it used to work and stopped.
I am pushing this as obvious, tell me if there is any problem.
I built-tested this with a MIPS toolchain (ct-ng), but I don't have any
setup to test it. At least it should put back the buildbot builder in a
better shape.
gdb/ChangeLog:
* mips-linux-nat.c (write_watchpoint_regs): Add NULL as ptrace's 4th
parameter.
(mips_linux_new_thread): Likewise.
* nat/mips-linux-watch.c (mips_linux_read_watch_registers): Likewise.
gdb/gdbserver/ChangeLog:
* linux-mips-low.c (mips_linux_prepare_to_resume): Add NULL as
ptrace's 4th parameter.
Building in C++ mode issues ~40 warnings like this:
../../src/gdb/linux-nat.c: In function ‘int linux_handle_extended_wait(lwp_info*, int, int)’:
../../src/gdb/linux-nat.c:2016:51: warning: invalid conversion from ‘int’ to ‘__ptrace_request’ [-fpermissive]
ptrace (PTRACE_GETEVENTMSG, pid, 0, &new_pid);
The issue is that in glibc, ptrace's first parameter is an enum.
That's not a problem if we pick the PTRACE_XXX requests from
sys/ptrace.h, as those will be values of the corresponding enum.
However, we have fallback definitions for PTRACE_XXX symbols when the
system headers miss them (such as PTRACE_GETEVENTMSG above), and those
are plain integer constants. E.g., nat/linux-ptrace.h:
#define PTRACE_GETEVENTMSG 0x4201
One idea would be to fix this by defining those fallbacks like:
-#define PTRACE_GETEVENTMSG 0x4201
+#define PTRACE_GETEVENTMSG ((enum __ptrace_request) 0x4201)
However, while glibc's ptrace uses enum __ptrace_request for first
parameter:
extern long int ptrace (enum __ptrace_request __request, ...) __THROW;
other libc's, like e.g., Android's bionic do not -- in that case, the
first parameter is int:
long ptrace(int request, pid_t pid, void * addr, void * data);
So the fix I came up is to make configure/ptrace.m4 also detect the
type of the ptrace's first parameter and defin PTRACE_TYPE_ARG1, as
already does the for parameters 3-4, and then simply wrap ptrace with
a macro that casts the first argument to the detected type. (I'm
leaving adding a nicer wrapper for when we drop building in C).
While this adds the wrapper, GNU/Linux files won't use it until the
next patch, which makes all native GNU/Linux files include
gdb_ptrace.h.
gdb/ChangeLog:
2015-07-24 Pedro Alves <palves@redhat.com>
* ptrace.m4 (ptrace tests): Test in C++ mode. Try with 'enum
__ptrace_request as first parameter type instead of int.
(PTRACE_TYPE_ARG1): Define.
* nat/gdb_ptrace.h [!PTRACE_TYPE_ARG5] (ptrace): Define as wrapper
that casts first argument to PTRACE_TYPE_ARG1.
* config.in: Regenerate.
* configure: Regenerate.
gdb/gdbserver/ChangeLog:
2015-07-24 Pedro Alves <palves@redhat.com>
* config.in: Regenerate.
* configure: Regenerate.
Now that gdbserver's configure defines PTRACE_TYPE_ARGx etc., we'll be
able to make gdbserver use gdb_ptrace.h too. Move it to the native
target files directory.
gdb/ChangeLog:
2015-07-24 Pedro Alves <palves@redhat.com>
* gdb_ptrace.h: Move ...
* nat/gdb_ptrace.h: ... here.
* inf-ptrace.c: Adjust.
There are also some duplication on getting HW watchpoint/breakpoint
registers info between GDB and GDBserver. This patch moves them
to nat/aarch64-linux-hw-point.c.
Note that ENABLE_NLS is not defined in GDBserver, so it should be OK
to use _( markup.
gdb:
2015-07-21 Yao Qi <yao.qi@linaro.org>
* aarch64-linux-nat.c (aarch64_linux_get_debug_reg_capacity):
Move it to nat/aarch64-linux-hw-point.c.
(aarch64_linux_child_post_startup_inferior): Update.
* nat/aarch64-linux-hw-point.c (aarch64_linux_get_debug_reg_capacity):
New function.
* nat/aarch64-linux-hw-point.h (aarch64_linux_get_debug_reg_capacity):
Declare it.
gdb/gdbserver:
2015-07-21 Yao Qi <yao.qi@linaro.org>
* linux-aarch64-low.c (aarch64_arch_setup): Remove code and call
aarch64_linux_get_debug_reg_capacity.
This patch is to fix two ARI warnings for nat/aarch64-linux-hw-point.{c,h}.
gdb:
2015-07-20 Yao Qi <yao.qi@linaro.org>
* nat/aarch64-linux-hw-point.c (aarch64_handle_unaligned_watchpoint):
Re-indent the code.
* nat/aarch64-linux-hw-point.h: Use ULONGEST rather than
"unsigned long long".
When I look at test fails related to watchpoint on aarch64-linux,
I find there are some code duplicates between GDB and GDBserver.
This patch is to move some of them to a nat/aarch64-linux-hw-point.{h,c}.
The only change I do is about the dr_changed_t typedef, which was
ULONGEST in GDB and 'unsigned long long' in GDBserver. Each bit
of dr_changed_t represents a status of each HW breakpoint or
watchpoint register, and the max number of HW breakpoint or watchpoint
registers is 16, so the width of 'unsigned long long' is sufficient.
gdb:
2015-07-17 Yao Qi <yao.qi@linaro.org>
* Makefile.in (HFILES_NO_SRCDIR): Add
nat/aarch64-linux-hw-point.h.
(aarch64-linux-hw-point.o): New rule.
* nat/aarch64-linux-hw-point.h: New file.
* nat/aarch64-linux-hw-point.c: New file.
* aarch64-linux-nat.c: Include nat/aarch64-linux-hw-point.h.
(AARCH64_HBP_MAX_NUM): Move to nat/aarch64-linux-hw-point.h.
(AARCH64_HWP_MAX_NUM, AARCH64_HBP_ALIGNMENT): Likewise.
(AARCH64_HWP_ALIGNMENT): Likewise.
(AARCH64_HWP_MAX_LEN_PER_REG): Likewise.
(AARCH64_DEBUG_NUM_SLOTS, AARCH64_DEBUG_ARCH): Likewise.
(AARCH64_DEBUG_ARCH_V8, DR_MARK_ALL_CHANGED): Likewise.
(DR_MARK_N_CHANGED, DR_CLEAR_CHANGED): Likewise.
(DR_HAS_CHANGED, DR_N_HAS_CHANGE): Likewise.
(aarch64_num_bp_regs, aarch64_num_wp_regs): Likewise.
(struct aarch64_debug_reg_state): Likewise.
(struct arch_lwp_info): Likewise.
(aarch64_linux_set_debug_regs): Likewise.
(aarch64_notify_debug_reg_change): Remove static.
(aarch64_align_watchpoint): Likewise.
(DR_CONTROL_ENABLED, DR_CONTROL_LENGTH): Likewise.
(aarch64_watchpoint_length): Likewise.
(aarch64_point_encode_ctrl_reg): Likewise
(aarch64_point_is_aligned): Likewise.
(aarch64_dr_state_insert_one_point): Likewise.
(aarch64_dr_state_remove_one_point): Likewise.
(aarch64_handle_breakpoint): Likewise.
(aarch64_handle_aligned_watchpoint): Likewise.
(aarch64_handle_unaligned_watchpoint): Likewise.
(aarch64_handle_watchpoint): Likewise.
* config/aarch64/linux.mh (NAT_FILE): Add
aarch64-linux-hw-point.o.
gdb/gdbserver:
2015-07-17 Yao Qi <yao.qi@linaro.org>
* Makefile.in (aarch64-linux-hw-point.o): New rule.
* configure.srv (srv_tgtobj): Append aarch64-linux-hw-point.o.
* linux-aarch64-low.c: Include nat/aarch64-linux-hw-point.h.
(AARCH64_HBP_MAX_NUM): Move to nat/aarch64-linux-hw-point.h.
(AARCH64_HWP_MAX_NUM, AARCH64_HBP_ALIGNMENT): Likewise.
(AARCH64_HWP_ALIGNMENT): Likewise.
(AARCH64_HWP_MAX_LEN_PER_REG): Likewise.
(AARCH64_DEBUG_NUM_SLOTS, AARCH64_DEBUG_ARCH): Likewise.
(aarch64_num_bp_regs, aarch64_num_wp_regs): Likewise.
(AARCH64_DEBUG_ARCH_V8, DR_MARK_ALL_CHANGED): Likewise.
(DR_MARK_N_CHANGED, DR_CLEAR_CHANGED): Likewise.
(DR_HAS_CHANGED, DR_N_HAS_CHANGE): Likewise.
(struct aarch64_debug_reg_state): Likewise.
(struct arch_lwp_info): Likewise.
(aarch64_align_watchpoint): Likewise.
(DR_CONTROL_ENABLED, DR_CONTROL_LENGTH): Likewise.
(aarch64_watchpoint_length): Likewise.
(aarch64_point_encode_ctrl_reg): Likewise
(aarch64_point_is_aligned): Likewise.
(aarch64_align_watchpoint): Likewise.
(aarch64_linux_set_debug_regs):
(aarch64_dr_state_insert_one_point): Likewise.
(aarch64_dr_state_remove_one_point): Likewise.
(aarch64_handle_breakpoint): Likewise.
(aarch64_handle_aligned_watchpoint): Likewise.
(aarch64_handle_unaligned_watchpoint): Likewise.
(aarch64_handle_watchpoint): Likewise.
This should be just a move with no changes.
gdb/ChangeLog
2015-07-15 Aleksandar Ristovski <aristovski@qnx.com
Jan Kratochvil <jan.kratochvil@redhat.com>
Move linux_find_memory_regions_full & co.
* linux-tdep.c (nat/linux-maps.h): Include.
(gdb_regex.h): Remove the include.
(enum filterflags, struct smaps_vmflags, read_mapping, decode_vmflags)
(mapping_is_anonymous_p, dump_mapping_p): Moved to nat/linux-maps.c.
(linux_find_memory_region_ftype): Moved typedef to nat/linux-maps.h.
(linux_find_memory_regions_full): Moved definition to nat/linux-maps.c.
* nat/linux-maps.c: Include ctype.h, target/target-utils.h, gdb_regex.h
and target/target.h.
(struct smaps_vmflags, read_mapping, decode_vmflags)
(mapping_is_anonymous_p, dump_mapping_p): Move from linux-tdep.c.
(linux_find_memory_regions_full): Move from linux-tdep.c.
* nat/linux-maps.h (read_mapping): New declaration.
(linux_find_memory_region_ftype, enum filterflags): Moved from
linux-tdep.c.
(linux_find_memory_regions_full): New declaration.
* target.c (target/target-utils.h): Include.
(read_alloc_pread_ftype): Moved typedef to target/target-utils.h.
(read_alloc, read_stralloc_func_ftype, read_stralloc): Moved
definitions to target/target-utils.c.
* target.h (target_fileio_read_stralloc): Move it to target/target.h.
* target/target-utils.c (read_alloc, read_stralloc): Move definitions
from target.c.
* target/target-utils.h (read_alloc_pread_ftype): New typedef.
(read_alloc): New declaration.
(read_stralloc_func_ftype): New typedef.
(read_stralloc): New declaration.
* target/target.h (target_fileio_read_stralloc): Move it from target.h.
gdb/gdbserver/ChangeLog
2015-07-15 Aleksandar Ristovski <aristovski@qnx.com
Jan Kratochvil <jan.kratochvil@redhat.com>
* target.c: Include target/target-utils.h and fcntl.h.
(target_fileio_read_stralloc_1_pread, target_fileio_read_stralloc_1)
(target_fileio_read_stralloc): New functions.
Fix the ARI warning about the use of unsigned long long. We can't use
ULONGEST as this is defined unsigned long on 64-bit systems. This will
result in a compile error when storing a pointer to an unsigned long long
structure field (declared in perf_event.h as __u64) in a ULONGEST * variable.
Use size_t to hold the buffer size inside GDB and __u64 when interfacing the
Linux kernel.
gdb/
* nat/linux-btrace.c (perf_event_read): Change the type of DATA_HEAD.
(perf_event_read_all): Change the type of SIZE and DATA_HEAD.
(perf_event_read_bts): Change the type of SIZE and READ.
(linux_enable_bts): Change the type of SIZE, PAGES, DATA_SIZE,
and DATA_OFFSET. Move DATA_SIZE declaration. Restrict the buffer size
to UINT_MAX. Check for overflows when using DATA_HEAD from the perf
mmap page.
(linux_enable_pt): Change the type of PAGES and SIZE. Restrict the
buffer size to UINT_MAX.
(linux_read_bts): Change the type of BUFFER_SIZE, SIZE, DATA_HEAD, and
DATA_TAIL.
* nat/linux-btrace.h (struct perf_event_buffer)<size, data_head>
<last_head>: Change type.
* common/btrace-common.h (struct btrace_dat_pt) <size>: Change type.
* common/btrace-common.c (btrace_data_append): Change the type of
SIZE.
* btrace.c (parse_xml_raw): Change the type of SIZE. Change oddness
check.
* nat/linux-namespaces.c (setns): Rename from this ...
(do_setns): ... to this. Support calling setns if it exists.
(mnsh_handle_setns): Call do_setns.
Do not use strerror(), instead use safe_strerror().
gdb/
* nat/linux-btrace.c (kernel_supports_bts, kernel_supports_pt):
Use safe_strerror() instead of strerror().
In struct perf_event_mmap_page there are new fields data_size and data_offset
that give the location of the perf_event data buffer relative to the mmap
page. Use them if they are present.
gdb/
* nat/linux-btrace.c (linux_enable_bts): Check for
PERF_ATTR_SIZE_VER5.
Check for data_offset and data_size fields. Use them.
Adds a new command "record btrace pt" to configure the kernel to use
Intel(R) Processor Trace instead of Branch Trace Strore.
The "record btrace" command chooses the tracing format automatically.
Intel(R) Processor Trace support requires Linux 4.1 and libipt.
gdb/
* NEWS: Announce new commands "record btrace pt" and "record pt".
Announce new options "set|show record btrace pt buffer-size".
* btrace.c: Include "rsp-low.h".
Include "inttypes.h".
(btrace_add_pc): Add forward declaration.
(pt_reclassify_insn, ftrace_add_pt, btrace_pt_readmem_callback)
(pt_translate_cpu_vendor, btrace_finalize_ftrace_pt)
(btrace_compute_ftrace_pt): New.
(btrace_compute_ftrace): Support BTRACE_FORMAT_PT.
(check_xml_btrace_version): Update version check.
(parse_xml_raw, parse_xml_btrace_pt_config_cpu)
(parse_xml_btrace_pt_raw, parse_xml_btrace_pt)
(btrace_pt_config_cpu_attributes, btrace_pt_config_children)
(btrace_pt_children): New.
(btrace_children): Add support for "pt".
(parse_xml_btrace_conf_pt, btrace_conf_pt_attributes): New.
(btrace_conf_children): Add support for "pt".
* btrace.h: Include "intel-pt.h".
(btrace_pt_error): New.
* common/btrace-common.c (btrace_format_string, btrace_data_fini)
(btrace_data_empty): Support BTRACE_FORMAT_PT.
* common/btrace-common.h (btrace_format): Add BTRACE_FORMAT_PT.
(struct btrace_config_pt): New.
(struct btrace_config)<pt>: New.
(struct btrace_data_pt_config, struct btrace_data_pt): New.
(struct btrace_data)<pt>: New.
* features/btrace-conf.dtd (btrace-conf)<pt>: New.
(pt): New.
* features/btrace.dtd (btrace)<pt>: New.
(pt, pt-config, cpu): New.
* nat/linux-btrace.c (perf_event_read, perf_event_read_all)
(perf_event_pt_event_type, kernel_supports_pt)
(linux_supports_pt): New.
(linux_supports_btrace): Support BTRACE_FORMAT_PT.
(linux_enable_bts): Free tinfo on error.
(linux_enable_pt): New.
(linux_enable_btrace): Support BTRACE_FORMAT_PT.
(linux_disable_pt): New.
(linux_disable_btrace): Support BTRACE_FORMAT_PT.
(linux_fill_btrace_pt_config, linux_read_pt): New.
(linux_read_btrace): Support BTRACE_FORMAT_PT.
* nat/linux-btrace.h (struct btrace_tinfo_pt): New.
(struct btrace_target_info)<pt>: New.
* record-btrace.c (set_record_btrace_pt_cmdlist)
(show_record_btrace_pt_cmdlist): New.
(record_btrace_print_pt_conf): New.
(record_btrace_print_conf): Support BTRACE_FORMAT_PT.
(btrace_ui_out_decode_error): Support BTRACE_FORMAT_PT.
(cmd_record_btrace_pt_start): New.
(cmd_record_btrace_start): Support BTRACE_FORMAT_PT.
(cmd_set_record_btrace_pt, cmd_show_record_btrace_pt): New.
(_initialize_record_btrace): Add new commands.
* remote.c (PACKET_Qbtrace_pt, PACKET_Qbtrace_conf_pt_size): New.
(remote_protocol_features): Add "Qbtrace:pt".
Add "Qbtrace-conf:pt:size".
(remote_supports_btrace): Support BTRACE_FORMAT_PT.
(btrace_sync_conf): Support PACKET_Qbtrace_conf_pt_size.
(remote_enable_btrace): Support BTRACE_FORMAT_PT.
(_initialize_remote): Add new commands.
gdbserver/
* linux-low.c: Include "rsp-low.h"
(linux_low_encode_pt_config, linux_low_encode_raw): New.
(linux_low_read_btrace): Support BTRACE_FORMAT_PT.
(linux_low_btrace_conf): Support BTRACE_FORMAT_PT.
(handle_btrace_enable_pt): New.
(handle_btrace_general_set): Support "pt".
(handle_btrace_conf_general_set): Support "pt:size".
doc/
* gdb.texinfo (Process Record and Replay): Spell out that variables
and registers are not available during btrace replay.
Describe the new "record btrace pt" command.
Describe the new "set|show record btrace pt buffer-size" options.
(General Query Packets): Describe the new Qbtrace:pt and
Qbtrace-conf:pt:size packets.
Expand "bts" to "Branch Trace Store".
Update the branch trace DTD.
stdint.h was added to common-defs.h some months ago and should
no longer be included directly by any file.
gdb_assert.h was added to common-defs.h nearly a year ago, but
three includes have crept in since then.
This commit removes all such redundant include directives.
gdb/ChangeLog:
* common/buffer.c (stdint.h): Do not include.
* common/print-utils.c (stdint.h): Likewise.
* compile/compile-c-symbols.c (gdb_assert.h): Likewise.
* compile/compile-c-types.c (gdb_assert.h): Likewise.
* ft32-tdep.c (gdb_assert.h): Likewise.
* guile/scm-utils.c (stdint.h): Likewise.
* i386-linux-tdep.c (stdint.h): Likewise.
* i386-tdep.c (stdint.h): Likewise.
* nat/linux-btrace.c (stdint.h): Likewise.
* nat/linux-btrace.h (stdint.h): Likewise.
* nat/linux-ptrace.c (stdint.h): Likewise.
* nat/mips-linux-watch.h (stdint.h): Likewise.
* ppc-linux-nat.c (stdint.h): Likewise.
* python/python-internal.h (stdint.h): Likewise.
* stub-termcap.c (stdlib.h): Likewise.
* target/target.h (stdint.h): Likewise.
* xtensa-linux-nat.c (stdint.h): Likewise.
gdb/gdbserver/ChangeLog:
* linux-i386-ipa.c (stdint.h): Do not include.
* lynx-i386-low.c (stdint.h): Likewise.
* lynx-ppc-low.c (stdint.h): Likewise.
* mem-break.c (stdint.h): Likewise.
* thread-db.c (stdint.h): Likewise.
* tracepoint.c (stdint.h): Likewise.
* win32-low.c (stdint.h): Likewise.
This commit changes the debug printing code in linux-namespaces.c
to use pulongest instead of "%ld".
gdb/ChangeLog:
* nat/linux-namespaces.c (mnsh_send_message): Use pulongest.
(mnsh_recv_message): Likewise.
This commit fixes the following ARI warning:
gdb/nat/linux-namespaces.c:28: regression: Do not include
wait.h or sys/wait.h, instead include gdb_wait.h
gdb/ChangeLog:
* nat/linux-namespaces.c (gdb_wait.h): New include.
(sys/wait.h): Do not include.
This commit removes linux_proc_pid_get_ns, and updates its only
caller to use linux_ns_same instead.
gdb/ChangeLog:
* linux-thread-db.c (nat/linux-namespaces.h): New include.
(check_pid_namespace_match): Use linux_ns_same rather than
linux_proc_pid_get_ns to spot PID namespace mismatches.
* nat/linux-procfs.h (linux_proc_pid_get_ns): Remove.
* nat/linux-procfs.c (linux_proc_pid_get_ns): Likewise.
Macros PTRACE_GETREGSET and PTRACE_SETREGSET are defined locally in
some places in GDB and GDBserver. This patch is to move them to
nat/linux-ptrace.h to avoid duplication.
gdb:
2015-06-01 Yao Qi <yao.qi@linaro.org>
* amd64-linux-nat.c: Include "nat/linux-ptrace.h".
* i386-linux-nat.c: Likewise.
* nat/linux-ptrace.h (PTRACE_GETREGSET, PTRACE_SETREGSET): Define.
* s390-linux-nat.c: Include "nat/linux-ptrace.h".
(PTRACE_GETREGSET, PTRACE_SETREGSET): Remove.
* x86-linux-nat.c: Include "nat/linux-ptrace.h".
* x86-linux-nat.h (PTRACE_GETREGSET, PTRACE_SETREGSET): Remove.
gdb/gdbserver:
2015-06-01 Yao Qi <yao.qi@linaro.org>
* linux-s390-low.c (PTRACE_GETREGSET, PTRACE_SETREGSET): Remove.
* linux-x86-low.c: Likewise.
Building in C++ mode errors with:
~~~
g++ -fpermissive (...) /home/pedro/gdb/mygit/src/gdb/gdbserver/../nat/x86-linux.c
In file included from /home/pedro/gdb/mygit/src/gdb/gdbserver/../nat/x86-linux.h:23:0,
from /home/pedro/gdb/mygit/src/gdb/gdbserver/../nat/x86-linux.c:21:
/home/pedro/gdb/mygit/src/gdb/gdbserver/../nat/linux-nat.h:74:13: error: use of enum ‘target_stop_reason’ without previous declaration
extern enum target_stop_reason lwp_stop_reason (struct lwp_info *lwp);
^
/home/pedro/gdb/mygit/src/gdb/gdbserver/../nat/linux-nat.h:74:70: error: invalid type in declaration before ‘;’ token
extern enum target_stop_reason lwp_stop_reason (struct lwp_info *lwp);
^
~~~
gdb/ChangeLog:
2015-05-15 Pedro Alves <palves@redhat.com>
* nat/linux-nat.h: Include "target/waitstatus.h".
This patch implements basic support for follow-fork and detach-on-fork on
extended-remote Linux targets. Only 'fork' is supported in this patch;
'vfork' support is added n a subsequent patch. This patch depends on
the previous patches in the patch series.
Sufficient extended-remote functionality has been implemented here to pass
gdb.base/multi-forks.exp, as well as gdb.base/foll-fork.exp with the
catchpoint tests commented out. Some other fork tests fail with this
patch because it doesn't provide the architecture support needed for
watchpoint inheritance or fork catchpoints.
The implementation follows the same general structure as for the native
implementation as much as possible.
This implementation includes:
* enabling fork events in linux-low.c in initialize_low and
linux_enable_extended_features
* handling fork events in gdbserver/linux-low.c:handle_extended_wait
- when a fork event occurs in gdbserver, we must do the full creation
of the new process, thread, lwp, and breakpoint lists. This is
required whether or not the new child is destined to be
detached-on-fork, because GDB will make target calls that require all
the structures. In particular we need the breakpoint lists in order
to remove the breakpoints from a detaching child. If we are not
detaching the child we will need all these structures anyway.
- as part of this event handling we store the target_waitstatus in a new
member of the parent lwp_info structure, 'waitstatus'. This
is used to store extended event information for reporting to GDB.
- handle_extended_wait is given a return value, denoting whether the
handled event should be reported to GDB. Previously it had only
handled clone events, which were never reported.
* using a new predicate in gdbserver to control handling of the fork event
(and eventually all extended events) in linux_wait_1. The predicate,
extended_event_reported, checks a target_waitstatus.kind for an
extended ptrace event.
* implementing a new RSP 'T' Stop Reply Packet stop reason: "fork", in
gdbserver/remote-utils.c and remote.c.
* implementing new target and RSP support for target_follow_fork with
target extended-remote. (The RSP components were actually defined in
patch 1, but they see their first use here).
- remote target routine remote_follow_fork, which just sends the 'D;pid'
detach packet to detach the new fork child cleanly. We can't just
call target_detach because the data structures for the forked child
have not been allocated on the host side.
Tested on x64 Ubuntu Lucid, native, remote, extended-remote.
gdb/gdbserver/ChangeLog:
* linux-low.c (handle_extended_wait): Implement return value,
rename argument 'event_child' to 'event_lwp', handle
PTRACE_EVENT_FORK, call internal_error for unrecognized event.
(linux_low_ptrace_options): New function.
(linux_low_filter_event): Call linux_low_ptrace_options,
use different argument fo linux_enable_event_reporting,
use return value from handle_extended_wait.
(extended_event_reported): New function.
(linux_wait_1): Call extended_event_reported and set
status to report fork events.
(linux_write_memory): Add pid to debug message.
(reset_lwp_ptrace_options_callback): New function.
(linux_handle_new_gdb_connection): New function.
(linux_target_ops): Initialize new structure member.
* linux-low.h (struct lwp_info) <waitstatus>: New member.
* lynx-low.c: Initialize new structure member.
* remote-utils.c (prepare_resume_reply): Implement stop reason
"fork" for "T" stop message.
* server.c (handle_query): Call handle_new_gdb_connection.
* server.h (report_fork_events): Declare global flag.
* target.h (struct target_ops) <handle_new_gdb_connection>:
New member.
(target_handle_new_gdb_connection): New macro.
* win32-low.c: Initialize new structure member.
gdb/ChangeLog:
* linux-nat.c (linux_nat_ptrace_options): New function.
(linux_init_ptrace, wait_lwp, linux_nat_filter_event):
Call linux_nat_ptrace_options and use different argument to
linux_enable_event_reporting.
(_initialize_linux_nat): Delete call to
linux_ptrace_set_additional_flags.
* nat/linux-ptrace.c (current_ptrace_options): Rename to
supported_ptrace_options.
(additional_flags): Delete variable.
(linux_check_ptrace_features): Use supported_ptrace_options.
(linux_test_for_tracesysgood, linux_test_for_tracefork):
Likewise, and remove additional_flags check.
(linux_enable_event_reporting): Change 'attached' argument to
'options'. Use supported_ptrace_options.
(ptrace_supports_feature): Change comment. Use
supported_ptrace_options.
(linux_ptrace_set_additional_flags): Delete function.
* nat/linux-ptrace.h (linux_ptrace_set_additional_flags):
Delete function prototype.
* remote.c (remote_fork_event_p): New function.
(remote_detach_pid): New function.
(remote_detach_1): Call remote_detach_pid, don't mourn inferior
if doing detach-on-fork.
(remote_follow_fork): New function.
(remote_parse_stop_reply): Handle new "T" stop reason "fork".
(remote_pid_to_str): Print "process" strings for pid/0/0 ptids.
(init_extended_remote_ops): Initialize to_follow_fork.
This patch implements a mechanism for GDB to determine whether fork
events are supported in gdbserver. This is a preparatory patch for
remote fork and exec event support.
Two new RSP packets are defined to represent fork and vfork event
support. These packets are used just like PACKET_multiprocess_feature
to denote whether the corresponding event is supported. GDB sends
fork-events+ and vfork-events+ to gdbserver to inquire about fork
event support. If the response enables these packets, then GDB
knows that gdbserver supports the corresponding events and will
enable them.
Target functions used to query for support are included along with
each new packet.
In order for gdbserver to know whether the events are supported at the
point where the qSupported packet arrives, the code in nat/linux-ptrace.c
had to be reorganized. Previously it would test for fork/exec event
support, then enable the events using the pid of the inferior. When the
qSupported packet arrives there may not be an inferior. So the mechanism
was split into two parts: a function that checks whether the events are
supported, called when gdbserver starts up, and another that enables the
events when the inferior stops for the first time.
Another gdbserver change was to add some global variables similar to
multi_process, one per new packet. These are used to control whether
the corresponding fork events are enabled. If GDB does not inquire
about the event support in the qSupported packet, then gdbserver will
not set these "report the event" flags. If the flags are not set, the
events are ignored like they were in the past. Thus, gdbserver will
never send fork event notification to an older GDB that doesn't
recognize fork events.
Tested on Ubuntu x64, native/remote/extended-remote, and as part of
subsequent patches in the series.
gdb/gdbserver/ChangeLog:
* linux-low.c (linux_supports_fork_events): New function.
(linux_supports_vfork_events): New function.
(linux_target_ops): Initialize new structure members.
(initialize_low): Call linux_check_ptrace_features.
* lynx-low.c (lynx_target_ops): Initialize new structure
members.
* server.c (report_fork_events, report_vfork_events):
New global flags.
(handle_query): Add new features to qSupported packet and
response.
(captured_main): Initialize new global variables.
* target.h (struct target_ops) <supports_fork_events>:
New member.
<supports_vfork_events>: New member.
(target_supports_fork_events): New macro.
(target_supports_vfork_events): New macro.
* win32-low.c (win32_target_ops): Initialize new structure
members.
gdb/ChangeLog:
* nat/linux-ptrace.c (linux_check_ptrace_features): Change
from static to extern.
* nat/linux-ptrace.h (linux_check_ptrace_features): Declare.
* remote.c (anonymous enum): <PACKET_fork_event_feature,
* PACKET_vfork_event_feature>: New enumeration constants.
(remote_protocol_features): Add table entries for new packets.
(remote_query_supported): Add new feature queries to qSupported
packet.
(_initialize_remote): Exempt new packets from the requirement
to have 'set remote' commands.
This commit introduces a new function linux_proc_pid_to_exec_file
that shared Linux code can use to discover the filename of the
executable that was run to create a process on the system.
gdb/ChangeLog:
* nat/linux-procfs.h (linux_proc_pid_to_exec_file):
New declaration.
* nat/linux-procfs.c (linux_proc_pid_to_exec_file):
New function, factored out from...
* linux-nat.c (linux_child_pid_to_exec_file): ...here.
This patch adds cpu information on linux based on /proc/cpuinfo as :
cpus Listing of all cpus/cores on the system
This patch also reorders the info os commands so that they are listed
in alphabetical order.
gdb/ChangeLog:
* NEWS: Mention info os cpus support.
* gdb/nat/linux-osdata.c (linux_xfer_osdata_cpus): New function.
(struct osdata_type): Add cpus entry, reorder the entries in
alphabetical order.
gdb/doc/ChangeLog:
* gdb.texinfo (Operating System Auxiliary Information): Add info os cpus
documentation, reorder the info os entries in alphabetical order.
This commit moves two identical functions from gdb/x86-linux-nat.c and
gdb/gdbserver/linux-x86-low.c into the shared file gdb/nat/x86-linux.c.
gdb/ChangeLog:
* nat/x86-linux.h (x86_linux_new_thread): New declaration.
(x86_linux_prepare_to_resume): Likewise.
* x86-linux-nat.c (x86_linux_new_thread):
Moved to nat/x86-linux.c.
(x86_linux_prepare_to_resume): Likewise.
* nat/x86-linux.c (x86_linux_new_thread): New function.
(x86_linux_prepare_to_resume): Likewise.
gdb/gdbserver/ChangeLog:
* linux-x86-low.c (x86_linux_new_thread): Moved to
nat/x86-linux.c.
(x86_linux_prepare_to_resume): Likewise.
Doug Evans
Simon Marchi
Yao Qi
Simon Marchi
Don Breazeal
Markus Metzger
Ulrich Weigand
Gary Benson
Pedro Alves
Jan Kratochvil
Peter Bergner
Michael Eager
Antoine Tremblay