As defined in AArch64 AAPCS, short vectors are passed through V
registers, and its maximum alignment is 16-byte. This patch is
to reflect these rules in GDB. This patch fixes some fails in
gdb.base/gnu_vector.exp.
gdb:
2015-11-27 Yao Qi <yao.qi@linaro.org>
* aarch64-tdep.c (aarch64_type_align): For vector type, return
its length, but with the maximum of 16 bytes.
(is_hfa): Return zero for vector type.
(aarch64_push_dummy_call): Handle short vectors.
(aarch64_extract_return_value): Likewise.
(aarch64_store_return_value): Likewise.
Hi,
I see one fail on aarch64-linux testing,
FAIL: gdb.cp/annota2.exp: watch triggered on a.x (timeout)
because GDB prints two frames-invalid annotation but the test expects
only one.
next^M
^M
^Z^Zpost-prompt^M
^M
^Z^Zstarting^M
^M
^Z^Zframes-invalid^M
^M
^Z^Zframes-invalid^M
^M
Note I also see the fail on Debian-s390x-m64 too.
https://sourceware.org/ml/gdb-testers/2015-q4/msg07291.html
The test shouldn't only expect one frames-invalid annotation, because
there can be multiple times of stop/resume before the user visible
stop. Ulrich did something similar before
https://www.sourceware.org/ml/gdb-patches/2009-06/msg00118.html
This patch only changes ${frames_invalid} to \(${frames_invalid}\)*
in the regexp pattern.
The patch below fixes the fail on aarch64-linux.
gdb/testsuite:
2015-11-27 Yao Qi <yao.qi@linaro.org>
* gdb.cp/annota2.exp: Allow multiple occurrences of the
frames-invalid annotation.
Variable frames_invalid was defined, but wasn't used much. This patch
is to replace the literals in the regexp with ${frames_invalid}.
gdb/testsuite:
2015-11-27 Yao Qi <yao.qi@linaro.org>
* gdb.cp/annota2.exp: Use ${frames_invalid}.
I couldn't find a test that verified the thread name functionality, so I
created a new one.
A target board can define gdb,no_thread_names if it doesn't support thread
names and wants to skip the tests that uses them.
This test has been made with Linux in mind. Not all platforms use
pthread_setname_np to set the thread name, but some #ifdefs can be added
later in order to support other platforms.
Tested on x86-64 Ubuntu 14.04, native and remote.
gdb/testsuite/ChangeLog:
* gdb.threads/names.exp: New file.
* gdb.threads/names.c: New file.
* README: Mention gdb,no_thread_names.
This patch adds support for thread names in the remote protocol, and
updates gdb/gdbserver to use it. The information is added to the XML
description sent in response to the qXfer:threads:read packet.
gdb/ChangeLog:
* linux-nat.c (linux_nat_thread_name): Replace implementation by call
to linux_proc_tid_get_name.
* nat/linux-procfs.c (linux_proc_tid_get_name): New function,
implementation inspired by linux_nat_thread_name.
* nat/linux-procfs.h (linux_proc_tid_get_name): New declaration.
* remote.c (struct private_thread_info) <name>: New field.
(free_private_thread_info): Free name field.
(remote_thread_name): New function.
(thread_item_t) <name>: New field.
(clear_threads_listing_context): Free name field.
(start_thread): Get name xml attribute.
(thread_attributes): Add "name" attribute.
(remote_update_thread_list): Copy name field.
(init_remote_ops): Assign remote_thread_name callback.
* target.h (target_thread_name): Update comment.
* NEWS: Mention remote thread name support.
gdb/gdbserver/ChangeLog:
* linux-low.c (linux_target_ops): Use linux_proc_tid_get_name.
* server.c (handle_qxfer_threads_worker): Refactor to include thread
name in reply.
* target.h (struct target_ops) <thread_name>: New field.
(target_thread_name): New macro.
gdb/doc/ChangeLog:
* gdb.texinfo (Thread List Format): Mention thread names.
Since this code path returns a string owned by the target (we don't know how
it's allocated, could be a static read-only string), it's safer if we return
a constant string. If, for some reasons, the caller wishes to modify the
string, it should make itself a copy.
gdb/ChangeLog:
* linux-nat.c (linux_nat_thread_name): Constify return value.
* target.h (struct target_ops) <to_thread_name>: Likewise.
(target_thread_name): Likewise.
* target.c (target_thread_name): Likewise.
* target-delegates.c (debug_thread_name): Regenerate.
* python/py-infthread.c (thpy_get_name): Constify local variables.
* thread.c (print_thread_info): Likewise.
(thread_find_command): Likewise.
If GDB has been configured without libipt support, i.e. HAVE_LIBIPT is
undefined, and is running on a system that supports Intel(R) Processor Trace,
GDB will run into an internal error when trying to decode the trace.
(gdb) record btrace
(gdb) s
usage (name=0x7fffffffe954 "fib-64")
at src/fib.c:12
12 fprintf(stderr, "usage: %s <num>\n", name);
(gdb) info record
Active record target: record-btrace
Recording format: Intel(R) Processor Trace.
Buffer size: 16kB.
gdb/btrace.c:971: internal-error: Unexpected branch trace format.
A problem internal to GDB has been detected,
further debugging may prove unreliable.
Quit this debugging session? (y or n)
This requires a system with Linux kernel 4.1 or later running on a 5th
Generation Intel Core processor or later.
The issue is documented as PR 19297.
When trying to enable branch tracing, in addition to checking the target
support for the requested branch tracing format, also check whether GDB
supports. it.
gdb/
* btrace.c (btrace_enable): Check whether HAVE_LIBIPT is defined.
testsuite/
* lib/gdb.exp (skip_btrace_pt_tests): Check for a "GDB does not
support" error.
gdb/ChangeLog:
2015-11-24 Pedro Alves <palves@redhat.com>
* NEWS: Mention that a few "info" commands now list the
corresponding items in ascending ID order.
Before:
(gdb) info display
Auto-display expressions now in effect:
Num Enb Expression
3: y 1
2: y 1
1: y 1
After:
(gdb) info display
Auto-display expressions now in effect:
Num Enb Expression
1: y 1
2: y 1
3: y 1
gdb/ChangeLog:
2015-11-24 Pedro Alves <palves@redhat.com>
PR 17539
* printcmd.c (display_command): Append new display at the end of
the list.
gdb/testsuite/ChangeLog:
2015-11-24 Pedro Alves <palves@redhat.com>
PR 17539
* gdb.base/display.exp: Expect displays to be sorted in ascending
order. Use multi_line.
* gdb.base/solib-display.exp: Likewise.
Before:
(gdb) info checkpoints
3 process 29132 at 0x4008ad, file foo.c, line 81
2 process 29131 at 0x4008ad, file foo.c, line 81
1 process 29130 at 0x4008ad, file foo.c, line 81
* 0 Thread 0x7ffff7fc5740 (LWP 29128) (main process) at 0x4008ad, file foo.c, line 81
After:
(gdb) info checkpoints
* 0 Thread 0x7ffff7fc5740 (LWP 29128) (main process) at 0x4008ad, file foo.c, line 81
1 process 29130 at 0x4008ad, file foo.c, line 81
2 process 29131 at 0x4008ad, file foo.c, line 81
3 process 29132 at 0x4008ad, file foo.c, line 81
gdb/ChangeLog:
2015-11-24 Pedro Alves <palves@redhat.com>
PR 17539
* printcmd.c (display_command): Append new display at the end of
the list.
gdb/testsuite/ChangeLog:
2015-11-24 Pedro Alves <palves@redhat.com>
PR 17539
* gdb.base/display.exp: Expect displays to be sorted in ascending
order. Use multi_line.
* gdb.base/solib-display.exp: Likewise.
Before:
(gdb) info threads
Id Target Id Frame
3 Thread 0x7ffff77c3700 (LWP 29035) callme () at foo.c:30
2 Thread 0x7ffff7fc4700 (LWP 29034) 0x000000000040087b in child_function_2 (arg=0x0) at foo.c:60
* 1 Thread 0x7ffff7fc5740 (LWP 29030) 0x0000003b37209237 in pthread_join (threadid=140737353893632, thread_return=0x0) at pthread_join.c:92
After:
(gdb) info threads
Id Target Id Frame
* 1 Thread 0x7ffff7fc5740 (LWP 29030) 0x0000003b37209237 in pthread_join (threadid=140737353893632, thread_return=0x0) at pthread_join.c:92
2 Thread 0x7ffff7fc4700 (LWP 29034) 0x000000000040087b in child_function_2 (arg=0x0) at foo.c:60
3 Thread 0x7ffff77c3700 (LWP 29035) callme () at foo.c:30
gdb/doc/ChangeLog:
2015-11-24 Pedro Alves <palves@redhat.com>
PR 17539
* gdb.texinfo (Inferiors and Programs): Adjust "maint info
program-spaces" example to ascending order listing.
(Threads): Adjust "info threads" example to ascending order
listing.
(Forks): Adjust "info inferiors" example to ascending order
listing.
gdb/ChangeLog:
2015-11-24 Pedro Alves <palves@redhat.com>
PR 17539
* inferior.c (add_inferior_silent): Append the new inferior to the
end of the list.
* progspace.c (add_program_space): Append the new pspace to the
end of the list.
* thread.c (new_thread): Append the new thread to the end of the
list.
gdb/testsuite/ChangeLog:
2015-11-24 Pedro Alves <palves@redhat.com>
PR 17539
* gdb.base/foll-exec-mode.exp: Adjust to GDB listing inferiors and
threads in ascending order.
* gdb.base/foll-fork.exp: Likewise.
* gdb.base/foll-vfork.exp: Likewise.
* gdb.base/multi-forks.exp: Likewise.
* gdb.mi/mi-nonstop.exp: Likewise.
* gdb.mi/mi-nsintrall.exp: Likewise.
* gdb.multi/base.exp: Likewise.
* gdb.multi/multi-arch.exp: Likewise.
* gdb.python/py-inferior.exp: Likewise.
* gdb.threads/break-while-running.exp: Likewise.
* gdb.threads/execl.exp: Likewise.
* gdb.threads/gcore-thread.exp: Likewise.
* gdb.threads/info-threads-cur-sal.exp: Likewise.
* gdb.threads/kill.exp: Likewise.
* gdb.threads/linux-dp.exp: Likewise.
* gdb.threads/multiple-step-overs.exp: Likewise.
* gdb.threads/next-bp-other-thread.exp: Likewise.
* gdb.threads/step-bg-decr-pc-switch-thread.exp: Likewise.
* gdb.threads/step-over-lands-on-breakpoint.exp: Likewise.
* gdb.threads/step-over-trips-on-watchpoint.exp: Likewise.
* gdb.threads/thread-find.exp: Likewise.
* gdb.threads/tls.exp: Likewise.
* lib/mi-support.exp (mi_reverse_list): Delete.
(mi_check_thread_states): No longer reverse list.
... like the kernel does.
gcore-thread.exp has a check to make sure the signalled thread is the
current thread after loading the core back, but that just works by
accident, because the signalled thread happened to be the last thread
on the thread list, and gdb currently iterates over threads in reverse
order.
So this fixes gcore-thread.exp once we start walking threads in
ascending number.
gdb/ChangeLog:
2015-11-24 Pedro Alves <palves@redhat.com>
* linux-tdep.c (find_stop_signal): Delete.
(struct linux_corefile_thread_data) <pid>: Remove field.
(linux_corefile_thread_callback): Rename to ...
(linux_corefile_thread): ... this. Now takes a struct
linux_corefile_thread_data pointer rather than a void pointer.
Remove thread state and thread pid checks.
(linux_make_corefile_notes): Prefer dumping the signalled thread
first. Use ALL_NON_EXITED_THREADS instead of
iterate_over_threads.
When trying to save fast tracepoints to file, gdb returns internal failure:
gdb/breakpoint.c:13446: internal-error: unhandled tracepoint type 27
A problem internal to GDB has been detected, further debugging may prove unreliable.
And no file including the fast tracepoints definition is created.
The patch also extends save-trace.exp to test saving tracepoint with a
fast tracepoint in there. Note that because this test doesn't actually
inserts the tracepoints in the program, we can run it with targets that
don't actually support fast tracepoints (or tracepoints at all).
gdb/ChangeLog:
* breakpoint.c (tracepoint_print_recreate): Fix logic error
if -> else if.
gdb/testsuite/ChangeLog:
* gdb.trace/actions.c: Include trace-common.h.
(main): Add a location for a fast tracepoint.
* gdb.trace/save-trace.exp: Set a fast tracepoint in addition to
the normal tracepoints.
(gdb_verify_tracepoints): Adjust number of expected tracepoints.
Some code is duplicated, to run the test twice with absolute and
relative paths, so I factored it out in a few procs. It uses
with_test_prefix to differentiate between test runs.
I replaced usages of "save-tracepoints" with "save tracepoint", since
the former is deprecated.
I also removed the "10.x", as it doesn't make much sense anymore. It
isn't used in general in the testsuite, and I don't think it's really
useful.
gdb/testsuite/ChangeLog:
* save-trace.exp: Factor out code to these...
(gdb_save_tracepoints): New.
(gdb_load_tracepoints): New.
(do_save_load_test): New.
The comment for the code in question says:
/* If the minimal symbol has a zero size, save it
but keep scanning backwards looking for one with
a non-zero size. A zero size may mean that the
symbol isn't an object or function (e.g. a
label), or it may just mean that the size was not
specified. */
As written, the code in question will only scan past the first symbol
of zero size. My change fixes the implementation to match the
comment.
Having this correct is important when the compiler generates several
local labels that are left in place by the linker. (I've been told
that the linker should eliminate these symbols, but I know of one
architecture for which this is not happening.)
I've created a test case called asmlabel.c. It's pretty simple:
main (int argc, char **argv)
{
asm ("L0:");
v = 0;
asm ("L1:");
v = 1; /* set L1 breakpoint here */
asm ("L2:");
v = 2; /* set L2 breakpoint here */
return 0;
}
If breakpoints are placed on the lines indicated by the comments,
this is the behavior of GDB built without my patch:
(gdb) continue
Continuing.
Breakpoint 2, L1 () at asmlabel.c:26
26 v = 1; /* set L1 breakpoint here */
Note that L1 appears as the function instead of main. This is not
what we want to happen. With my patch in place, we see the desired
behavior instead:
(gdb) continue
Continuing.
Breakpoint 2, main (argc=1, argv=0x7fffffffdb88) at asmlabel.c:26
26 v = 1; /* set L1 breakpoint here */
gdb/ChangeLog:
* minsyms.c (lookup_minimal_symbol_by_pc_section_1): Scan backwards
over all zero-sized symbols.
gdb/testsuite/ChangeLog:
* gdb.base/asmlabel.exp: New test.
* gdb.base/asmlabel.c: New test case.
One of our users reported an internal error using the "bt full"
command. In their situation, reproducing involved the following
scenario:
(gdb) frame 1
(gdb) bt full
#0 0xf7783430 in __kernel_vsyscall ()
No symbol table info available.
#1 0xf5550aeb in waitpid () at ../sysdeps/unix/syscall-template.S:81
No locals.
[...]
#6 0x0fe83139 in xxxx (arg=...)
[...some locals printed, and then...]
<S17b> =
[...]/dwarf2loc.c:364: internal-error: dwarf_expr_frame_base: Assertion
`framefunc != NULL' failed.
As shown above, the error happens while GDB is trying to print the value
of <S17b>, which is a local string internally generated by the compiler.
For that, it finds that the array lives in memory, and therefore tries
to create a struct value for it via:
case DWARF_VALUE_MEMORY:
{
CORE_ADDR address = dwarf_expr_fetch_address (ctx, 0);
[...]
retval = value_at_lazy (type, address + byte_offset);
Unfortunately for us, TYPE happens to be an array whose bounds
are dynamic. More precisely, the bounds of our arrays are described
in the debugging info as being...
<4><2c1985e>: Abbrev Number: 33 (DW_TAG_subrange_type)
<2c1985f> DW_AT_type : <0x2c1989c>
<2c19863> DW_AT_lower_bound : <0x2c19835>
<2c19867> DW_AT_upper_bound : <0x2c19841>
... which are references to a pair of local variables. For instance,
the lower bound is a reference to the following DIE
<3><2c19835>: Abbrev Number: 32 (DW_TAG_variable)
<2c19836> DW_AT_name : [...]
<2c1983a> DW_AT_type : <0x2c198b4>
<2c1983e> DW_AT_artificial : 1
<2c1983e> DW_AT_location : 2 byte block: 91 58 (DW_OP_fbreg: -40)
As a result of the above, value_at_lazy indirectly triggers
a resolution of TYPE (via value_from_contents_and_address),
which means a resolution of TYPE's bounds, and as seen in
the DW_AT_location attribute above for our bounds, computing
the bound's location requires the frame (its location expression
uses DW_OP_fbreg).
Unfortunately for us, value_at_lazy does not get passed a frame,
we've lost the relevant frame when we try to resolve the array's
bounds. Instead, resolve_dynamic_range gets calls dwarf2_evaluate_property
with NULL as the frame:
static struct type *
resolve_dynamic_range (struct type *dyn_range_type,
struct property_addr_info *addr_stack)
{
[...]
if (dwarf2_evaluate_property (prop, NULL, addr_stack, &value))
^^^^
... which then handles this by using the selected frame instead:
if (frame == NULL && has_stack_frames ())
frame = get_selected_frame (NULL);
In our case, the selected frame happens to be frame #1, which is
a frame where we have a minimal amount of debugging info, and in
particular, no debug info for the function itself. And because of that,
when we try to determine the frame's base...
static void
dwarf_expr_frame_base (void *baton, const gdb_byte **start,
size_t * length)
{
struct dwarf_expr_baton *debaton = (struct dwarf_expr_baton *) baton;
const struct block *bl = get_frame_block (debaton->frame, NULL);
[...]
framefunc = block_linkage_function (bl);
... framefunc ends up being NULL, which triggers the assert
in that same function:
gdb_assert (framefunc != NULL);
This patches avoids the issue by temporarily setting the selected_frame
before printing the locals of each frames.
This patch also adds a small testcase, which reproduces the same
issue, but with a slightly different outcome:
(gdb) bt full
#0 0x000000000040049a in opaque_routine ()
No symbol table info available.
#1 0x0000000000400532 in main () at wrong_frame_bt_full-main.c:20
my_table_size = 3
my_table = <error reading variable my_table (frame address is not available.)>
With this patch, the output becomes:
(gdb) bt full
[...]
my_table = {0, 1, 2}
gdb/ChangeLog:
* stack.c (print_frame_local_vars): Temporarily set the selected
frame to FRAME while printing the frame's local variables.
gdb/testsuite/ChangeLog:
* gdb.base/wrong_frame_bt_full-main.c: New file.
* gdb.base/wrong_frame_bt_full-opaque.c: New file.
* gdb.base/wrong_frame_bt_full.exp: New file.
This crash is observable by debugging a threaded program on LynxOS.
On the GDB side, this is what we would see:
% gdb q
(gdb) target remote machine:4444
(gdb) break q.adb:6
(gdb) cont
[gdb hits breakpoint]
(gdb) cont
Remote connection closed <<<--- expected: [Inferior 1 (Remote target) exited normally]
On the gdbserver side, which was launched as usual:
% gdbserver --once :4444 q
Segmentation fault (core dumped)
Ooops!
The problem happens while GDB is trying to handle the thread termination
event of the thread that hit the breakpoint. It started happening after
the following change was made:
commit 96e7a1eb6d
Date: Fri Oct 16 11:08:38 2015 -0400
Subject: gdbserver: Reset current_thread when the thread is removed.
Reset current_thread and make sure 'remove_process' is used
after all associated threads have been removed first.
More precisely:
. GDBserver receives the execution-resume order;
. lynx-low resumes it succesfully, and then relies on lynx_wait_1
to wait for the next event;
. We quickly receive one, which lynx_wait_1 analyzes to be
a "thread exit" event, and therefore does...
case SIGTHREADEXIT:
remove_thread (find_thread_ptid (new_ptid));
lynx_continue (new_ptid);
goto retry;
=> remove_thread causes current_thread to be set to NULL...
(that's the recent change mentioned above)
=> ... which causes problems during lynx_continue, because
it calls lynx_resume, which calls regcache_invalidate,
which unfortunately assumes that CURRENT_THREAD is not NULL:
void
regcache_invalidate (void)
{
/* Only update the threads of the current process. */
SEGV!--> int pid = ptid_get_pid (current_thread->entry.id);
find_inferior (&all_threads, regcache_invalidate_one, &pid);
}
Since the problem at hand is caused by trying to figure out which
inferior to reset the regcache for, and since lynx_resume actually
had that info, this patch fixes the problem by introducing a new
routine called regcache_invalidate_pid, which invalidates the cache
of the given pid; and then modifies lynx_resume use that new routine
rather than relying on regcache_invalidate to invalidate the regcache
of the expected inferior.
gdb/gdbserver/ChangeLog:
* regcache.h (regcache_invalidate_pid): Add declaration.
* regcache.c (regcache_invalidate_pid): New function, extracted
from regcache_invalidate.
(regcache_invalidate): Reimplement using regcache_invalidate_pid.
Add trivial documentation comment.
* lynx-low.c: Use regcache_invalidate_pid instead of
regcache_invalidate.
We noticed the following hang trying to run a program where one
of the subroutines we built without debugging info (opaque_routine):
$ gdb my_program
(gdb) break opaque_routine
(gdb) run
[...hangs...]
The problem comes from the fact that, at the breakpoint's address,
we have the following code:
=> 0x0000000000401994 <+4>: pop %rbp
At some point after hitting the breakpoint and stopping, GDB calls
amd64_windows_frame_decode_epilogue, which then gets stuck in the
following infinite loop:
| /* We don't care about the instruction deallocating the frame:
| if it hasn't been executed, the pc is still in the body,
| if it has been executed, the following epilog decoding will work. */
|
| /* First decode:
| - pop reg [41 58-5f] or [58-5f]. */
|
| while (1)
| {
| /* Read opcode. */
| if (target_read_memory (pc, &op, 1) != 0)
| return -1;
|
| if (op >= 0x40 && op <= 0x4f)
| {
| /* REX prefix. */
| rex = op;
|
| /* Read opcode. */
| if (target_read_memory (pc + 1, &op, 1) != 0)
| return -1;
| }
| else
| rex = 0;
|
| if (op >= 0x58 && op <= 0x5f)
| {
| /* pop reg */
| gdb_byte reg = (op & 0x0f) | ((rex & 1) << 3);
|
| cache->prev_reg_addr[amd64_windows_w2gdb_regnum[reg]] = cur_sp;
| cur_sp += 8;
| }
| else
| break;
|
| /* Allow the user to break this loop. This shouldn't happen as the
| number of consecutive pop should be small. */
| QUIT;
| }
Nothing in that loop updates PC, and therefore, because the instruction
we stopped at is a "pop", we keep looping forever doing the same thing
over and over!
This patch fixes the issue by advancing PC to the beginning of
the next instruction if the current one is a "pop reg" instruction.
gdb/ChangeLog:
* amd64-windows-tdep.c (amd64_windows_frame_decode_epilogue):
Increment PC in while loop skipping "pop reg" instructions.
The following issue has been observed on arm-android, trying to step
over the following line of code:
Put_Line (">>> " & Integer'Image (Message (I)));
Below is a copy of the GDB transcript:
(gdb) cont
Breakpoint 1, q.dump (message=...) at q.adb:11
11 Put_Line (">>> " & Integer'Image (Message (I)));
(gdb) next
0x00016000 in system.concat_2.str_concat_2 ()
The expected behavior for the "next" command is to step over
the call to Put_Line and stop at line 12:
(gdb) next
12 I := I + 1;
What happens during the next step is that the code for line 11
above make a call to system.concat_2.str_concat_2 (to implement
the '&' string concatenation operator) before making the call
to Put_Line. While stepping, GDB stops eventually stops at the
first instruction of that function, and fails to detect that
it's a function call from where we were before, and so decides
to stop stepping.
And the reason why it fails to detect that we landed inside a function
call is because it fails to unwind from that function:
(gdb) bt
#0 0x00016000 in system.concat_2.str_concat_2 ()
#1 0x0001bc74 in ?? ()
Debugging GDB, I found that GDB decides to use the ARM unwind info
for that function, which contains the following data:
0x16000 <system__concat_2__str_concat_2>: 0x80acb0b0
Compact model index: 0
0xac pop {r4, r5, r6, r7, r8, r14}
0xb0 finish
0xb0 finish
But, in fact, using that data is wrong, in this case, because
it mentions a pop of 6 registers, and therefore hints at a frame
size of 24 bytes. The problem is that, because we're at the first
instruction of the function, the 6 registers haven't been pushed
to the stack yet. In other words, using the ARM unwind entry above,
GDB is tricked into thinking that the frame size is 24 bytes, and
that the return address (r14) is available on the stack.
One visible manifestation of this issue can been seen by looking
at the value of the stack pointer, and the frame's base address:
(gdb) p /x $sp
$2 = 0xbee427b0
(gdb) info frame
Stack level 0, frame at 0xbee427c8:
^^^^^^^^^^
||||||||||
The frame's base address should be equal to the value of the stack
pointer at entry. And you eventually get the correct frame address,
as well as the correct backtrace if you just single-step one additional
instruction, past the push:
(gdb) x /i $pc
=> 0x16000 <system__concat_2__str_concat_2>:
push {r4, r5, r6, r7, r8, lr}
(gdb) stepi
(gdb) bt
#0 0x00016004 in system.concat_2.str_concat_2 ()
#1 0x00012b6c in q.dump (message=...) at q.adb:11
#2 0x00012c3c in q () at q.adb:19
Digging further, I found that GDB tries to use the ARM unwind info
only when sure that it is relevant, as explained in the following
comment:
/* The ARM exception table does not describe unwind information
for arbitrary PC values, but is guaranteed to be correct only
at call sites. We have to decide here whether we want to use
ARM exception table information for this frame, or fall back [...]
There is one case where it decides that the info is relevant,
described in the following comment:
/* We also assume exception information is valid if we're currently
blocked in a system call. The system library is supposed to
ensure this, so that e.g. pthread cancellation works.
For that, it just parses the instruction at the address it believes
to be the point of call, and matches it against an "svc" instruction.
For instance, for a non-thumb instruction, it is at...
get_frame_pc (this_frame) - 4
... and the code checking looks like the following.
if (safe_read_memory_integer (get_frame_pc (this_frame) - 4, 4,
byte_order_for_code, &insn)
&& (insn & 0x0f000000) == 0x0f000000 /* svc */)
exc_valid = 1;
However, the reason why this doesn't work in our case is that
because we are at the first instruction of a function in the innermost
frame. That frame can't possibly be making a call, and therefore
be stuck on a system call.
What the code above ends up doing is checking the instruction
just before the start of our function, which in our case is not
even an actual instruction, but unlucky for us, happens to match
the pattern it is looking for, thus leading GDB to improperly
trust the ARM unwinding data.
gdb/ChangeLog:
* arm-tdep.c (arm_exidx_unwind_sniffer): Do not check for a frame
stuck on a system call if the given frame is the innermost frame.
See the comment added in configure.ac for more details behind
this change.
gdb/gdbserver/ChangeLog:
* configure.ac: Do not call AC_CHECK_TYPES for Elf32_auxv_t
and Elf64_auxv_t if the target is Android.
Using the gdb.ada/var_rec_arr.exp test, where the program declares
an array of variant records...
type Record_Type (I : Small_Type := 0) is record
S : String (1 .. I);
end record;
type Array_Type is array (Integer range <>) of Record_Type;
... and then a variable A1 of type Array_Type, the following command
ocassionally trigger an internal error trying to allocate more memory
than we have left:
(gdb) ptype a1(1)
[...]/utils.c:1089: internal-error: virtual memory exhausted.
A problem internal to GDB has been detected,
[...]
What happens is that recent versions of GNAT are able to generate
DWARF expressions for type Record_Type, and therefore the record's
DW_AT_byte_size is not a constant, which unfortunately breaks
an assumption made by dwarf2read.c:read_structure_type when it does:
attr = dwarf2_attr (die, DW_AT_byte_size, cu);
if (attr)
{
TYPE_LENGTH (type) = DW_UNSND (attr);
}
As a result of this, when ada_evaluate_subexp tries to create
a value_zero for a1(1) while processing the OP_FUNCALL operator
as part of evaluating the subscripting operation in no-side-effect
mode, we try to allocate a value with a bogus size, potentially
triggering the out-of-memory internal error.
This patch avoids this issue by setting the length to zero in
this case. Until we decide to start supporting dynamic type
lengths in GDB's type struct, and it's not clear yet that
this is worth the effort (see added comment), that's probably
the best we can do.
gdb/ChangeLog:
* dwarf2read.c (read_structure_type): Set the type's length
to zero if it has a DW_AT_byte_size attribute which is not
a constant.
gdb/testsuite/ChangeLog:
* testsuite/gdb.ada/var_rec_arr.exp: Add "ptype a1(1)" test.
This patch fixes a typo in target.c:read_memory_robust, where
it calls read_whatever_is_readable with the function arguments
in the wrong order. Depending on the address being read, it
can cause an xmalloc with a huge size, resulting in an assertion
failure, or just read something other than what was requested.
The problem only arises when GDB is handling an MI
"-data-read-memory-bytes" request and the initial target_read returns
an error status. Note that read_memory_robust is only called from
the MI code.
gdb/ChangeLog:
* gdb/target.c (read_memory_robust): Call
read_whatever_is_readable with arguments in the correct order.
The Linux kernel disables the FPU upon returning to userland. This
introduces spurious failures in the register preservation tests in
callfuncs.exp, since the pstate.PEF bit gets cleared after system
calls.
This patch filters out the pstate register in sparc64-*-linux-gnu
targets, so the relevant tests are no longer fooled and pass.
gdb/testsuite/ChangeLog:
2015-11-20 Jose E. Marchesi <jose.marchesi@oracle.com>
* gdb.base/callfuncs.exp (fetch_all_registers): Filter out the
pstate register when comparing registers values in
sparc64-*-linux-gnu targets to avoid spurious differences.
This patch adds a missing include that makes the test program to not
be built (--Wimplicit-function-declaration).
gdb/testsuite/ChangeLog:
2015-11-20 Jose E. Marchesi <jose.marchesi@oracle.com>
* gdb.arch/sparc-sysstep.c: Include unistd.h for getpid.
The target_process_qsupported method is called for each qSupported
feature that the common code does not recognize. The only current
implementation, for x86 Linux (x86_linux_process_qsupported), assumes
that it either is called with the "xmlRegisters=i386" feature, or that
it is isn't called at all, indicating the connected GDB predates x86
XML descriptions.
That's a bad assumption however. If GDB sends in a new/unknown (to
core gdbserver) feature after "xmlRegisters=i386", say, something like
qSupported:xmlRegisters=i386;UnknownFeature+, then when
target_process_qsupported is called for "UnknownFeature+",
x86_linux_process_qsupported clears the 'use_xml' global and calls
x86_linux_update_xmltarget, and gdbserver ends up _not_ reporting a
XML description...
This commit changes the target_process_qsupported API to instead pass
down a vector of unprocessed qSupported features in one go.
(There's an early call to target_process_qsupported(NULL) that
indicates "starting qSupported processing". There's no matching call
to mark the end of processing, though. I first fixed this by passing
(char *)-1 to indicate that, and adjusted the x86 backend to only
clear 'use_xml' when qSupported processing starts, and then only call
x86_linux_update_xmltarget() when (char *)-1 was passed. However, I
wasn't that happy with the hack and came up this alternative version.)
gdb/gdbserver/ChangeLog:
2015-11-19 Pedro Alves <palves@redhat.com>
* linux-low.c (linux_process_qsupported): Change prototype.
Adjust.
* linux-low.h (struct linux_target_ops) <process_qsupported>:
Change prototype.
* linux-x86-low.c (x86_linux_process_qsupported): Change prototype
and adjust to loop over all features.
* server.c (handle_query) <qSupported>: Adjust to call
target_process_qsupported once, passing it a vector of unprocessed
features.
* target.h (struct target_ops) <process_qsupported>: Change
prototype.
(target_process_qsupported): Adjust.
gdbserver's target_process_qsupported is called for each feature that
the gdbserver common code does not recognize. The only current
implementation, for x86 Linux, does this:
static void
x86_linux_process_qsupported (const char *query)
{
/* Return if gdb doesn't support XML. If gdb sends "xmlRegisters="
with "i386" in qSupported query, it supports x86 XML target
descriptions. */
use_xml = 0;
if (query != NULL && startswith (query, "xmlRegisters="))
{
char *copy = xstrdup (query + 13);
char *p;
for (p = strtok (copy, ","); p != NULL; p = strtok (NULL, ","))
{
if (strcmp (p, "i386") == 0)
{
use_xml = 1;
break;
}
}
free (copy);
}
x86_linux_update_xmltarget ();
}
Notice that this clears use_xml and calls x86_linux_update_xmltarget
each time target_process_qsupported is called. So if gdb sends in any
unknown feature after "xmlRegisters=i386", like e.g.,
"xmlRegisters=i386;UnknownFeature+" gdbserver ends up not reporting a
XML description...
Work around this by having GDB send the "xmlRegisters=" feature last.
gdb/ChangeLog:
2015-11-19 Pedro Alves <palves@redhat.com>
* remote.c (remote_query_supported): Send the "xmlRegisters="
feature last.
There is this build failure when building in C++:
/home/simark/src/binutils-gdb/gdb/nat/aarch64-linux-hw-point.c: In function ‘void aarch64_linux_set_debug_regs(const aarch64_debug_reg_state*, int, int)’:
/home/simark/src/binutils-gdb/gdb/nat/aarch64-linux-hw-point.c:564:64: error: ‘count’ cannot appear in a constant-expression
iov.iov_len = (offsetof (struct user_hwdebug_state, dbg_regs[count - 1])
^
We can simplify the computation and make g++ happy at the same time by
formulating as:
size of fixed part + size of variable part
thus...
size of fixed part + count * size of one variable part element
thus...
offsetof (struct user_hwdebug_state, dbg_regs) + count * sizeof (regs.dbg_reg[0]);
gdb/ChangeLog:
* nat/aarch64-linux-hw-point.c (aarch64_linux_set_debug_regs): Change
form of iov_len computation.
Both x86_64 GNU/Linux and x86_64 mingw-w64 build cleanly with
--enable-targets=all. This enables -Werror by default in C++ mode
too, in order to let the buildbot catch C++ build regressions for us.
gdb/ChangeLog:
2015-11-19 Pedro Alves <palves@redhat.com>
* configure.ac (ERROR_ON_WARNING): Don't check whether in C++
mode.
* configure: Regenerate.
gdb/gdbserver/ChangeLog:
2015-11-19 Pedro Alves <palves@redhat.com>
* configure.ac (ERROR_ON_WARNING): Don't check whether in C++
mode.
* configure: Regenerate.
Both x86_64 GNU/Linux and x86_64 mingw-w64 build cleanly with
--enable-targets=all. Let's drop the -fpermissive hack, in order to
let the buildbot catch C++ build regressions for us.
gdb/ChangeLog:
2015-11-19 Pedro Alves <palves@redhat.com>
* build-with-cxx.m4 (GDB_AC_BUILD_WITH_CXX): Remove -fpermissive.
* configure: Regenerate.
gdb/gdbserver/ChangeLog:
2015-11-19 Pedro Alves <palves@redhat.com>
* configure: Regenerate.
Fixes:
src/gdb/breakpoint.c: In function ‘void update_watchpoint(watchpoint*, int)’:
src/gdb/breakpoint.c:2147:31: error: invalid conversion from ‘int’ to ‘target_hw_bp_type’ [-fpermissive]
base->loc->watchpoint_type = -1;
^
Seems better to rely on "address == -1 && length == -1" than on a enum
value that's not really part of the set of supposedly valid enum
values. Also, factor that out to separate functions for better
localization of the concept.
gdb/ChangeLog:
2015-11-19 Pedro Alves <palves@redhat.com>
* breakpoint.c (software_watchpoint_add_no_memory_location)
(is_no_memory_software_watchpoint): New functions.
(update_watchpoint): Use
software_watchpoint_add_memoryless_location.
(breakpoint_address_bits): Use is_no_memory_software_watchpoint.
Fixes:
src/gdb/remote.c: In function ‘void remote_unpush_target()’:
src/gdb/remote.c:4610:45: error: invalid conversion from ‘int’ to ‘strata’ [-fpermissive]
pop_all_targets_above (process_stratum - 1);
^
In file included from src/gdb/inferior.h:38:0,
from src/gdb/remote.c:25:
src/gdb/target.h:2299:13: error: initializing argument 1 of ‘void pop_all_targets_above(strata)’ [-fpermissive]
extern void pop_all_targets_above (enum strata above_stratum);
^
I used to carry a patch in the C++ branch that just did:
- pop_all_targets_above (process_stratum - 1);
+ pop_all_targets_above ((enum strata) (process_stratum - 1));
But then thought that maybe adding a routine that does exactly what we
need results in clearer code. This is the result.
gdb/ChangeLog:
2015-11-19 Pedro Alves <palves@redhat.com>
* remote.c (remote_unpush_target): Use
pop_all_targets_at_and_above instead of pop_all_targets_above.
* target.c (unpush_target_and_assert): New function, factored out
from ...
(pop_all_targets_above): ... here.
(pop_all_targets_at_and_above): New function.
* target.h (pop_all_targets_at_and_above): Declare.
The patch fixes the following errors in C++ build,
gdb/gdbserver/linux-aarch64-low.c: In function 'int emit_data_processing(uint32_t*, aarch64_opcodes, aarch64_register, aarch64_register, aarch64_operand)':
gdb/gdbserver/linux-aarch64-low.c:1071:52: error: invalid conversion from 'unsigned int' to 'aarch64_opcodes' [-fpermissive]
return emit_data_processing_reg (buf, opcode | operand_opcode, rd,
^
gdb/gdbserver:
2015-11-19 Yao Qi <yao.qi@linaro.org>
* linux-aarch64-low.c (emit_data_processing_reg): Change opcode
type to uint32_t.
This patch moves the enum definition out of the scope of struct, and
fixes the following error.
gdb/gdbserver/linux-aarch64-low.c:681:18: error: 'OPERAND_REGISTER' was not declared in this scope
operand.type = OPERAND_REGISTER;
^
gdb/gdbserver:
2015-11-19 Yao Qi <yao.qi@linaro.org>
* linux-aarch64-low.c (enum aarch64_operand_type): New.
(struct aarch64_operand): Move enum out.
If we constify value_cstring, we might as well constify this one.
gdb/ChangeLog:
* valops.c (value_string): Constify 'ptr' parameter.
* value.h (value_string): Constify 'ptr' parameter.
Commit 91ee7171d0 (MinGW and attribute format(printf/gnu_printf))
made common/common-defs.h depend on gnulib's substitute headers.
Turns out that that broke the gdbserver/ipa build (as the buildbots
discovered) because nothing is making sure that gnulib is built before
the ipa is.
gdb/gdbserver/ChangeLog:
2015-11-18 Pedro Alves <palves@redhat.com>
* Makefile.in (all_object_files): Add $IPA_OBJS.
Hi,
I build GDB with -fsanitize=address, and run testsuite. In
gdb.base/callfuncs.exp, I see the following error,
p t_float_values(0.0,0.0)
=================================================================
==8088==ERROR: AddressSanitizer: heap-buffer-overflow on address 0x6020000cb650 at pc 0x6e195c bp 0x7fff164f9770 sp 0x7fff164f9768
READ of size 16 at 0x6020000cb650 thread T0^
#0 0x6e195b in regcache_raw_write /home/yao/SourceCode/gnu/gdb/git/gdb/regcache.c:912
#1 0x6e1e52 in regcache_cooked_write /home/yao/SourceCode/gnu/gdb/git/gdb/regcache.c:945
#2 0x466d69 in pass_in_v /home/yao/SourceCode/gnu/gdb/git/gdb/aarch64-tdep.c:1101
#3 0x467512 in pass_in_v_or_stack /home/yao/SourceCode/gnu/gdb/git/gdb/aarch64-tdep.c:1196
#4 0x467d7d in aarch64_push_dummy_call /home/yao/SourceCode/gnu/gdb/git/gdb/aarch64-tdep.c:1335
The code in pass_in_v read contents from V registers (128 bit), but the
data passed through V registers can be less than 128 bit. In this case,
float is passed. So writing V registers contents into contents buff
will cause overflow. In this patch, we add an array reg[V_REGISTER_SIZE],
which is to hold the contents from V registers, and then copy useful
bits to buf.
gdb:
2015-11-18 Yao Qi <yao.qi@linaro.org>
* aarch64-tdep.c (pass_in_v): Add argument len. Add local array
reg. Callers updated.
Hi,
Some tests in gdb.threads/multiple-step-overs.exp fail on arm target
when the displaced stepping on, but they pass when displaced stepping
is off.
FAIL: gdb.threads/multiple-step-overs.exp: displaced=on: step: step
FAIL: gdb.threads/multiple-step-overs.exp: displaced=on: next: next
FAIL: gdb.threads/multiple-step-overs.exp: displaced=on: continue: continue
FAIL: gdb.threads/multiple-step-overs.exp: displaced=on: signal thr1: continue to sigusr1_handler
when displaced stepping is on,
Sending packet: $vCont;c#a8...infrun: infrun_async(1)^M <--- [1]
infrun: prepare_to_wait^M
infrun: target_wait (-1.0.0, status) =^M
infrun: -1.0.0 [Thread 0],^M
infrun: status->kind = ignore^M
infrun: TARGET_WAITKIND_IGNORE^M
infrun: prepare_to_wait^M
Packet received: T05swbreak:;0b:f8faffbe;0d:409ee7b6;0f:d0880000;thread:p635.636;core:0;^M
infrun: target_wait (-1.0.0, status) =^M
infrun: 1589.1590.0 [Thread 1590],^M
infrun: status->kind = stopped, signal = GDB_SIGNAL_TRAP^M
infrun: TARGET_WAITKIND_STOPPED^M
infrun: stop_pc = 0x88d0^M
infrun: context switch^M
infrun: Switching context from Thread 1591 to Thread 1590^
GDB resumes the whole process (all threads) rather than the specific
thread for which GDB wants to step over the breakpoint (as shown in [1]).
That is wrong because we resume a single thread and leave others stopped
when doing a normal step over where we temporarily remove the breakpoint,
single-step, reinsert the breakpoint, is that if we let other threads run
in the period while the breakpoint is removed, then these other threads
could miss the breakpoint. Since with displaced stepping, we don't ever
remove the breakpoint, it should be fine to let other threads run. However,
there's another reason that we should not let other threads run: that is
the case where some of those threads are also stopped for a breakpoint that
itself needs to be stepped over. If we just let those threads run, then
they immediately re-trap their breakpoint again.
when displaced stepping is off, GDB behaves correctly, only resumes
the specific thread (as shown in [2]).
Sending packet: $vCont;c:p611.613#b2...infrun: infrun_async(1)^M <-- [2]
infrun: prepare_to_wait^M
infrun: target_wait (-1.0.0, status) =^M
infrun: -1.0.0 [Thread 0],^M
infrun: status->kind = ignore^M
infrun: TARGET_WAITKIND_IGNORE^M
infrun: prepare_to_wait^M
Packet received: T05swbreak:;0b:f8faffbe;0d:409e67b6;0f:48880000;thread:p611.613;core:1;^M
infrun: target_wait (-1.0.0, status) =^M
infrun: 1553.1555.0 [Thread 1555],^M
infrun: status->kind = stopped, signal = GDB_SIGNAL_TRAP^M
infrun: TARGET_WAITKIND_STOPPED^M
infrun: clear_step_over_info^M
infrun: stop_pc = 0x8848
The current logic in GDB on deciding the set of threads to resume is:
/* Decide the set of threads to ask the target to resume. */
if ((step || thread_has_single_step_breakpoints_set (tp))
&& tp->control.trap_expected)
{
/* We're allowing a thread to run past a breakpoint it has
hit, by single-stepping the thread with the breakpoint
removed. In which case, we need to single-step only this
thread, and keep others stopped, as they can miss this
breakpoint if allowed to run. */
resume_ptid = inferior_ptid;
}
else
resume_ptid = internal_resume_ptid (user_step);
it doesn't handle the case correctly that GDB continue (instead of
single step) the thread for displaced stepping.
I also update the comment below to reflect the code. I remove the
"with the breakpoint removed" comment, because GDB doesn't remove
breakpoints in displaced stepping, so we don't have to worry that
other threads may miss the breakpoint.
Patch is regression tested on both x86_64-linux and arm-linux.
gdb:
2015-11-17 Yao Qi <yao.qi@linaro.org>
* infrun.c (resume): Check control.trap_expected only
when deciding the set of threads to resume.
We currently throw exceptions from signal handlers (e.g., for
Quit/ctrl-c). But throwing C++ exceptions from signal handlers is
undefined. (That doesn't restore signal masks, like siglongjmp does,
and, because asynchronous signals can arrive at any instruction, we'd
have to build _everything_ with -fasync-unwind-tables to make it
reliable.) It happens to work on x86_64 GNU/Linux at least, but it's
likely broken on other ports.
Until we stop throwing from signal handlers, use setjmp/longjmp based
exceptions in C++ mode as well.
gdb/ChangeLog:
2015-11-17 Pedro Alves <palves@redhat.com>
* common/common-exceptions.h (GDB_XCPT_SJMP, GDB_XCPT_TRY)
(GDB_XCPT_RAW_TRY, GDB_XCPT): Define.
Replace __cplusplus checks with GDB_XCPT checks throughout.
* common/common-exceptions.c: Replace __cplusplus checks with
GDB_XCPT checks throughout.
Cross building gdbserver for --host=x86_64-w64-mingw32 with gcc 4.8.4
20141219 (Fedora MinGW 4.8.4-1.fc20), I get:
src/gdb/gdbserver/tracepoint.c: In function 'cmd_qtdp':
src/gdb/gdbserver/tracepoint.c:2577:7: error: unknown conversion type character 'l' in format [-Werror=format=]
trace_debug ("Defined %stracepoint %d at 0x%s, "
^
src/gdb/gdbserver/tracepoint.c:2577:7: error: unknown conversion type character 'l' in format [-Werror=format=]
src/gdb/gdbserver/tracepoint.c:2577:7: error: too many arguments for format [-Werror=format-extra-args]
src/gdb/gdbserver/tracepoint.c: In function 'stop_tracing':
src/gdb/gdbserver/tracepoint.c:3447:7: error: unknown conversion type character 'l' in format [-Werror=format=]
trace_debug ("Stopping the trace because "
^
src/gdb/gdbserver/tracepoint.c:3447:7: error: too many arguments for format [-Werror=format-extra-args]
src/gdb/gdbserver/tracepoint.c: In function 'collect_data_at_tracepoint':
src/gdb/gdbserver/tracepoint.c:4651:3: error: unknown conversion type character 'l' in format [-Werror=format=]
trace_debug ("Making new traceframe for tracepoint %d at 0x%s, hit %" PRIu64,
^
src/gdb/gdbserver/tracepoint.c:4651:3: error: too many arguments for format [-Werror=format-extra-args]
src/gdb/gdbserver/tracepoint.c: In function 'collect_data_at_step':
src/gdb/gdbserver/tracepoint.c:4687:3: error: unknown conversion type character 'l' in format [-Werror=format=]
trace_debug ("Making new step traceframe for "
^
trace_debug is a macro that calls:
static void trace_vdebug (const char *, ...) ATTRIBUTE_PRINTF (1, 2);
The calls that fail checking use PRIu64, etc., like:
trace_debug ("Defined %stracepoint %d at 0x%s, "
"enabled %d step %" PRIu64 " pass %" PRIu64,
tpoint->type == fast_tracepoint ? "fast "
: tpoint->type == static_tracepoint ? "static " : "",
tpoint->number, paddress (tpoint->address), tpoint->enabled,
tpoint->step_count, tpoint->pass_count);
gnulib's stdio/printf module replacements may make %llu, etc. work on
mingw, instead of the MS-specific %I64u, and thus may make PRIu64
expand to %llu. However, gcc isn't aware of that, because libiberty's
ansidecl.h defines ATTRIBUTE_PRINTF as using attribute format(printf).
But, with that format, gcc checks for MS-style format strings (%I64u).
In order to have gcc expect gnu/standard formats, we need to use
gnu_printf format instead. Which version to use (printf/gnu_printf)
depends on msvcrt and mingw version, and so gnulib has a
configure-time check, and defines _GL_ATTRIBUTE_FORMAT_PRINTF
accordingly.
Since _GL_ATTRIBUTE_FORMAT_PRINTF is compatible with ATTRIBUTE_PRINTF,
the fix is simply to make use of the former.
gdb/ChangeLog:
2015-11-17 Pedro Alves <palves@redhat.com>
* common/common-defs.h (ATTRIBUTE_PRINTF): Redefine in terms of
_GL_ATTRIBUTE_FORMAT_PRINTF after including ansidecl.h.
With some toolchains, building in C++ mode stumbles on many instances
of:
In file included from ../../src/gdb/../include/splay-tree.h:43:0,
from ../../src/gdb/dcache.c:26:
build-gnulib/import/inttypes.h:61:3: error: #error "This file assumes that 'int' has exactly 32 bits. Please report your platform and compiler to <bug-gnulib@gnu.org>."
# error "This file assumes that 'int' has exactly 32 bits. Please report your platform and compiler to <bug-gnulib@gnu.org>."
^
make: *** [dcache.o] Error 1
That's:
#if !(INT_MIN == INT32_MIN && INT_MAX == INT32_MAX)
# error "This file assumes that 'int' has exactly 32 bits. Please report your platform and compiler to <bug-gnulib@gnu.org>."
#endif
I see it when cross building for --host=x86_64-w64-mingw32 using
Fedora 20's g++ (gcc version 4.8.4 20141219 (Fedora MinGW
4.8.4-1.fc20)), Simon reports seeing this on several cross compilers
too.
The issue is that on some hosts that predate C++11, when using C++ one
must define __STDC_CONSTANT_MACROS/__STDC_LIMIT_MACROS to make visible
the definitions of INTMAX_C / INTMAX_MAX etc.
This was a C99 requirement that later C++11 -- the first to define
stdint.h -- removed, and then C11 removed it as well.
https://www.gnu.org/software/gnulib/manual/html_node/stdint_002eh.html
says that gnulib's stdint.h fixes this, but because we run gnulib's
configure tests with a C compiler, gnulib determines that mingw's
stdint.h is C99-compliant, and doesn't actually replace it. Actually,
even though configuring gnulib with a C++ compiler does result in
gnulib replacing stdint.h, the resulting replacement is broken for
mingw, because it defines uintptr_t incorrectly. I sent a gnulib
patch upstream to fix that, here:
https://lists.gnu.org/archive/html/bug-gnulib/2015-11/msg00004.html
but then even with that, gnulib still stumbles on other
configured-with-C++-compiler problems.
So for now, until gnulib + C++ is fixed upstream and then gdb's copy
is updated, which may take a while, I think it's best to keep
configuring gnulib in C, and define
__STDC_LIMIT_MACROS/__STDC_CONSTANT_MACROS ourselves, just like C99
intended.
gdb/ChangeLog:
2015-11-17 Pedro Alves <palves@redhat.com>
* common/common-defs.h (__STDC_CONSTANT_MACROS)
(__STDC_LIMIT_MACROS): Define before including stdint.h.
Building in C++ errors out with:
../../src/gdb/windows-nat.c: In function 'int get_windows_debug_event(target_ops*, int, target_waitstatus*)':
../../src/gdb/windows-nat.c:1503:13: warning: invalid conversion from 'int' to 'gdb_signal' [-fpermissive]
last_sig = 1;
^
../../src/gdb/windows-nat.c:1533:43: warning: invalid conversion from 'int' to 'gdb_signal' [-fpermissive]
windows_resume (ops, minus_one_ptid, 0, 1);
^
../../src/gdb/windows-nat.c:1228:1: warning: initializing argument 4 of 'void windows_resume(target_ops*, ptid_t, int, gdb_signal)' [-fpermissive]
windows_resume (struct target_ops *ops,
^
Looking at the code, I can't figure out why we treat first chance
exceptions any different here.
AFAICS, we set last_sig to 1, and then call windows_resume passing
signal==1, so the DBG_EXCEPTION_NOT_HANDLED code path in win32_resume
is taken:
~~~
if (sig != GDB_SIGNAL_0)
{
if (current_event.dwDebugEventCode != EXCEPTION_DEBUG_EVENT)
{
OUTMSG (("Cannot continue with signal %d here.\n", sig));
}
else if (sig == last_sig)
continue_status = DBG_EXCEPTION_NOT_HANDLED;
else
OUTMSG (("Can only continue with recieved signal %d.\n", last_sig));
}
~~~
Fix this by removing this special casing. gdbserver also goes
straight to continuing with DBG_EXCEPTION_NOT_HANDLED, AFAICS.
gdb/ChangeLog:
2015-11-17 Pedro Alves <palves@redhat.com>
* windows-nat.c (handle_exception): Return 0 for first chance
exceptions.
(get_windows_debug_event): Adjust.
Building in C++ caught a buglet here:
../../../src/gdb/gdbserver/win32-low.c: In function 'void win32_resume(thread_resume*, size_t)':
../../../src/gdb/gdbserver/win32-low.c:929:11: error: invalid conversion from 'int' to 'gdb_signal' [-fpermissive]
sig = resume_info[0].sig;
^
../../../src/gdb/gdbserver/win32-low.c:934:11: error: invalid conversion from 'int' to 'gdb_signal' [-fpermissive]
sig = 0;
^
Signals in the "struct thread_resume" structure are host signals, not
gdb signals. The current code happens to work because the only
signals that the Windows port supports have the same number as the gdb
equivalent (see handle_exception for the win32 exception -> gdb signal
mapping).
gdb/gdbserver/ChangeLog:
2015-11-17 Pedro Alves <palves@redhat.com>
* win32-low.c (win32_resume): Use gdb_signal_from_host,
GDB_SIGNAL_0 and gdb_signal_to_string.
Fixes:
../../src/gdb/windows-nat.c:287:11: error: invalid conversion from 'int' to 'gdb_signal' [-fpermissive]
{-1, -1}};
^
The signal number here doesn't really matter.
gdb/ChangeLog:
2015-11-17 Pedro Alves <palves@redhat.com>
* windows-nat.c (xslate): Use GDB_SIGNAL_UNKNOWN instead of -1 as
signal number for terminator.
Fixes:
../../../src/gdb/gdbserver/win32-low.c: In function 'int win32_kill(int)':
../../../src/gdb/gdbserver/win32-low.c:823:46: error: invalid conversion from 'int' to 'target_waitkind' [-fpermissive]
struct target_waitstatus our_status = { 0 };
^
handle_output_debug_string doesn't use the parameter for anything
(it's an output parameter in the gdb version), so just remove it.
gdb/gdbserver/ChangeLog:
2015-11-17 Pedro Alves <palves@redhat.com>
* win32-low.c (handle_output_debug_string): Remove parameter.
(win32_kill): Remove our_status local and adjust call to
handle_output_debug_string.
(get_child_debug_event): Adjust call to
handle_output_debug_string.
Fixes a set of errors like:
../../src/gdb/windows-nat.c: In function 'void _initialize_loadable()':
../../src/gdb/windows-nat.c:2778:30: error: invalid conversion from 'void*' to 'BOOL (*)(DWORD) {aka int (*)(long unsigned int)}' [-fpermissive]
DebugActiveProcessStop = (void *)
^
gdb/ChangeLog:
2015-11-17 Pedro Alves <palves@redhat.com>
* windows-nat.c (AdjustTokenPrivileges_ftype)
(DebugActiveProcessStop_ftype, DebugBreakProcess_ftype)
(DebugSetProcessKillOnExit_ftype, EnumProcessModules_ftype)
(GetCurrentConsoleFont_ftype, GetModuleInformation_ftype)
(LookupPrivilegeValueA_ftype, OpenProcessToken_ftype)
(GetConsoleFontSize_ftype): New typedefs.
(AdjustTokenPrivileges, DebugActiveProcessStop)
(DebugBreakProcess, DebugSetProcessKillOnExit, EnumProcessModules)
(GetConsoleFontSize, GetCurrentConsoleFont, GetModuleInformation)
(LookupPrivilegeValueA, OpenProcessToken, GetConsoleFontSize):
Adjust.
(GetModuleFileNameEx_ftype): New typedef.
(GetModuleFileNameEx): Use it.
(_initialize_loadable): Define GPA macro and use it.
c_string_type contains values meant to be OR'ed together (even though
some bits are mutually exclusive), so it makes sense to make it an
enum flags type.
gdb/ChangeLog:
2015-11-17 Simon Marchi <simon.marchi@ericsson.com>
* c-exp.y (exp): Adjust, change enum c_string_type to
c_string_type.
(parse_string_or_char): Likewise.
* c-lang.c (charset_for_string_type): Likewise.
(classify_type): Likewise.
(c_printchar): Likewise.
(c_printstr): Likewise.
(evaluate_subexp_c): Likewise. And change cast to enum
c_string_type_values.
* c-lang.h: Include "common/enum_flags.h".
(enum c_string_type): Rename to...
(enum c_string_type_values): ...this.
(c_string_type): Define new enum flags type.
This patch fixes C++ build errors like this:
/home/pedro/gdb/mygit/cxx-convertion/src/gdb/linux-tdep.c:1126:35: error: invalid conversion from ‘int’ to ‘filterflags’ [-fpermissive]
| COREFILTER_HUGETLB_PRIVATE);
^
This is a case of enums used as bit flags. Unlike "regular" enums,
these values are supposed to be or'ed together. However, in C++, the
type of "(ENUM1 | ENUM2)" is int, and you then can't assign an int to
an enum variable without a cast. That means that this:
enum foo_flags flags = 0;
if (...)
flags |= FOO_FLAG1;
if (...)
flags |= FOO_FLAG2;
... would have to be written as:
enum foo_flags flags = (enum foo_flags) 0;
if (...)
flags = (enum foo_flags) (flags | FOO_FLAG1);
if (...)
flags = (enum foo_flags) (flags | FOO_FLAG2);
which is ... ugly. Alternatively, we'd have to use an int for the
variable's type, which isn't ideal either.
This patch instead adds an "enum flags" class. "enum flags" are
exactly the enums where the values are bits that are meant to be ORed
together.
This allows writing code like the below, while with raw enums this
would fail to compile without casts to enum type at the assignments to
'f':
enum some_flag
{
flag_val1 = 1 << 1,
flag_val2 = 1 << 2,
flag_val3 = 1 << 3,
flag_val4 = 1 << 4,
};
DEF_ENUM_FLAGS_TYPE(enum some_flag, some_flags)
some_flags f = flag_val1 | flag_val2;
f |= flag_val3;
It's also possible to assign literal zero to an enum flags variable
(meaning, no flags), dispensing either adding an awkward explicit "no
value" value to the enumeration or the cast to assignments from 0.
For example:
some_flags f = 0;
f |= flag_val3 | flag_val4;
Note that literal integers other than zero do fail to compile:
some_flags f = 1; // error
C is still supported -- DEF_ENUM_FLAGS_TYPE is just a typedef in that
case.
gdb/ChangeLog:
2015-11-17 Pedro Alves <palves@redhat.com>
* btrace.h: Include common/enum-flags.h.
(btrace_insn_flags): Define.
(struct btrace_insn) <flags>: Change type.
(btrace_function_flags): Define.
(struct btrace_function) <flags>: Change type.
(btrace_thread_flags): Define.
(struct btrace_thread_info) <flags>: Change type.
* c-exp.y (token_flags): Rename to ...
(token_flag): ... this.
(token_flags): Define.
(struct token) <flags>: Change type.
* common/enum-flags.h: New file.
* compile/compile-c-types.c (convert_qualified): Change type of
'quals' local.
* compile/compile-internal.h: Include "common/enum-flags.h".
(gcc_qualifiers_flags): Define.
* completer.c (enum reg_completer_targets): Rename to ...
(enum reg_completer_target): ... this.
(reg_completer_targets): Define.
(reg_or_group_completer_1): Change type of 'targets' parameter.
* disasm.c (do_mixed_source_and_assembly_deprecated): Change type
of 'psl_flags' local.
(do_mixed_source_and_assembly): Change type of 'psl_flags' local.
* infrun.c: Include "common/enum-flags.h".
(enum step_over_what): Rename to ...
(enum step_over_what_flag): ... this.
(step_over_what): Change type.
(start_step_over): Change type of 'step_what' local.
(thread_still_needs_step_over): Now returns a step_over_what.
Adjust.
(keep_going_pass_signal): Change type of 'step_what' local.
* linux-tdep.c: Include "common/enum-flags.h".
(enum filterflags): Rename to ...
(enum filter_flag): ... this.
(filter_flags): Define.
(dump_mapping_p): Change type of 'filterflags' parameter.
(linux_find_memory_regions_full): Change type of 'filterflags'
local.
(linux_find_memory_regions_full): Pass the address of an unsigned
int to sscanf instead of the address of an enum.
* record-btrace.c (btrace_print_lines): Change type of local
'psl_flags'.
(btrace_call_history): Replace 'flags' parameter
with 'int_flags' parameter. Adjust.
(record_btrace_call_history, record_btrace_call_history_range)
(record_btrace_call_history_from): Rename 'flags' parameter to
'int_flags'. Use record_print_flags.
* record.h: Include "common/enum-flags.h".
(record_print_flags): Define.
* source.c: Include "common/enum-flags.h".
(print_source_lines_base, print_source_lines): Change type of
flags parameter.
* symtab.h: Include "common/enum-flags.h".
(enum print_source_lines_flags): Rename to ...
(enum print_source_lines_flag): ... this.
(print_source_lines_flags): Define.
(print_source_lines): Change prototype.
Instead of adding a cast at the memory_error call, as needed for C++,
and have the reader understand the indirection, make it simple and
hardcode the generic memory error at the memory_error call site.
gdb/ChangeLog:
2015-11-17 Pedro Alves <palves@redhat.com>
* guile/scm-disasm.c (gdbscm_disasm_read_memory): Return -1 on
error instead of TARGET_XFER_E_IO.
(gdbscm_disasm_memory_error): Always pass TARGET_XFER_E_IO to
memory_error.
This patch fixes all occurences of left-shifting negative constants in C cod
which is undefined by the C standard.
gdb/testsuite/ChangeLog:
* lib/dwarf.exp (_note): Fix left shift of negative value.
* gdb.trace/trace-condition.exp: Likewise.
This patch fixes all occurences of left-shifting negative constants in C cod
which is undefined by the C standard.
gdb/ChangeLog:
* hppa-tdep.c (hppa_sign_extend, hppa_low_hppa_sign_extend)
(prologue_inst_adjust_sp, hppa_frame_cache): Fix left shift of negative
value.
* dwarf2read.c (read_subrange_type): Likewise.
Hi,
I build GDB with -fsanitize=address, and run testsuite. In
gdb.base/callfuncs.exp, I see the following error,
p/c fun1()
=================================================================^M
==9601==ERROR: AddressSanitizer: stack-buffer-overflow on address 0x7fffee858530 at pc 0x6df079 bp 0x7fffee8583a0 sp 0x7fffee858398
WRITE of size 16 at 0x7fffee858530 thread T0
#0 0x6df078 in regcache_raw_read /home/yao/SourceCode/gnu/gdb/git/gdb/regcache.c:673
#1 0x6dfe1e in regcache_cooked_read /home/yao/SourceCode/gnu/gdb/git/gdb/regcache.c:751
#2 0x4696a3 in aarch64_extract_return_value /home/yao/SourceCode/gnu/gdb/git/gdb/aarch64-tdep.c:1708
#3 0x46ae57 in aarch64_return_value /home/yao/SourceCode/gnu/gdb/git/gdb/aarch64-tdep.c:1918
We are extracting return value from V registers (128 bit), but only
allocate X_REGISTER_SIZE-byte array, which isn't sufficient. This
patch changes the array to V_REGISTER_SIZE.
gdb:
2015-11-16 Yao Qi <yao.qi@linaro.org>
* aarch64-tdep.c (aarch64_extract_return_value): Change array
buf's length to V_REGISTER_SIZE.
This patch changes the last argument of functions pass_in_x_or_stack,
pass_in_v_or_stack, pass_on_stack, and pass_in_x to type value *.
gdb:
2015-11-16 Yao Qi <yao.qi@linaro.org>
* aarch64-tdep.c (pass_in_x_or_stack): Change argument type
from bfd_byte * to value *. Caller updated.
(pass_in_x): Likewise.
(pass_in_v_or_stack): Likewise.
(pass_on_stack): Likewise.
Both aarch64_push_dummy_call and bfin_push_dummy_call only use args[i]
contents but then never write to them, so that we can use
value_contents instead.
gdb:
2015-11-16 Yao Qi <yao.qi@linaro.org>
* aarch64-tdep.c (aarch64_push_dummy_call): Call value_contents instead
of value_contents_writeable.
* bfin-tdep.c (bfin_push_dummy_call): Likewise.
When I build GDB with -fsanitize=address, and run testsuite,
some gdb.base/*.exp test triggers the ERROR below,
=================================================================
==7646==ERROR: AddressSanitizer: heap-buffer-overflow on address 0x603000242810 at pc 0x487844 bp 0x7fffe32e84e0 sp 0x7fffe32e84d8
READ of size 4 at 0x603000242810 thread T0
#0 0x487843 in push_stack_item /home/yao/SourceCode/gnu/gdb/git/gdb/arm-tdep.c:3405
#1 0x48998a in arm_push_dummy_call /home/yao/SourceCode/gnu/gdb/git/gdb/arm-tdep.c:3960
In that path, GDB passes value on stack, in an INT_REGISTER_SIZE slot,
but the value contents' length can be less than INT_REGISTER_SIZE, so
the contents will be accessed out of the bound. This patch adds an
array buf[INT_REGISTER_SIZE], and copy val to buf before writing them
to stack.
gdb:
2015-11-16 Yao Qi <yao.qi@linaro.org>
* arm-tdep.c (arm_push_dummy_call): New array buf. Store regval
to buf. Pass buf instead of val to push_stack_item.
This patch teaches GDB to support gnu vector in inferior calls. As a
result, fails in gdb.base/gnu_vector.exp are fixed. The calling
convention of gnu vector isn't documented in the AAPCS, because it
is the GCC extension. I checked the gcc/config/arm/arm.c, understand
how GCC pass arguments and return values, and do the same in GDB side.
The patch is tested with both hard float and soft float on arm-linux.
gdb:
2015-11-13 Yao Qi <yao.qi@linaro.org>
PR tdep/19051
* arm-tdep.c (arm_type_align): Return the right alignment
value for vector.
(arm_vfp_cprc_sub_candidate): Return true for 64-bit and
128-bit vector types.
(arm_return_in_memory): Handel vector type.
Current arm_return_in_memory isn't friendly to adding new things in it.
Moreover, a lot of stuff are about APCS, which is not used nowadays (AAPCS
is being used). This patch is to refactor arm_return_in_memory, so that
some code can be shared for both APCS and AAPCS at the beginning of
arm_return_in_memory, and then each ABI (APCS and AAPCS) are processed
separately.
gdb:
2015-11-13 Yao Qi <yao.qi@linaro.org>
* arm-tdep.c (arm_return_in_memory): Rewrite it.
(arm_return_value): Call arm_return_in_memory for
TYPE_CODE_COMPLEX.
This patch removes the leftover of the d10v stuff in the testsuite
directory. The d10v port was removed in GDB 6.7, but I happen to see
that there are still some leftovers about d10v in testsuite.
gdb/testsuite:
2015-11-13 Yao Qi <yao.qi@linaro.org>
* gdb.base/call-sc.exp (test_scalar_returns): Remove the
comments about d10v.
(test_scalar_returns): Likewise.
* gdb.base/d10v.ld: Remove.
* gdb.base/overlays.exp: Remove the target triplet checking for
d10v-*-*.
* gdb.base/structs.exp (test_struct_returns): Remove the
comments about d10v.
(test_struct_calls): Likewise.
gdb.base/gnu_vector.c printf the vector and gdb.base/gnu_vector.exp
expects the output by gdb_test_multiple. Nowadays, the test doesn't
expect the output from inferior_spawn_id, which is wrong. Even we
change the test to expect from inferior_spawn_id for the inferior
output, it is still possible the inferior exit before tcl/expect gets
the inferior output. We see this fail on both s390x-linux and
ppc-linux on buildbot,
FAIL: gdb.base/gnu_vector.exp: verify vector return value (the program exited)
https://sourceware.org/ml/gdb-testers/2015-q4/msg04922.htmlhttps://sourceware.org/ml/gdb-testers/2015-q4/msg04952.html
In order to address these two shortcomings above in gnu_vector.exp,
this patch rewrites the test a little bit. Get rid of checking the
inferior output, and instead checking them by printing them. In this
way, the test can also be run on the target without inferior io
(gdb,noinferiorio is set in the board file).
gdb/testsuite:
2015-11-13 Yao Qi <yao.qi@linaro.org>
* gdb.base/gnu_vector.exp: Check the return value by "p res".
* gdb.base/gnu_vector.c: Don't include stdio.h.
(main): Don't print res and call add_some_intvecs.
The assembly code for emitting the proper tracepointable instruction
was duplicated in many places. Keep it in one place, to reduce work
needed for new targets.
gdb/testsuite/ChangeLog:
* gdb.trace/change-loc.h: include "trace-common.h", remove SYMBOL
macro.
(func5): Removed.
(func4): Use FAST_TRACEPOINT_LABEL.
* gdb.trace/ftrace-lock.c: include "trace-common.h", remove SYMBOL
macro.
(func): Removed.
(thread_function): Use FAST_TRACEPOINT_LABEL.
* gdb.trace/ftrace.c: include "trace-common.h", remove SYMBOL macro.
(func): Remove.
(marker): Use FAST_TRACEPOINT_LABEL.
* gdb.trace/pendshr1.c: include "trace-common.h", remove SYMBOL macro.
(pendfunc1): Remove.
(pendfunc): Use FAST_TRACEPOINT_LABEL.
* gdb.trace/pendshr2.c: include "trace-common.h", remove SYMBOL macro.
(foo): Remove.
(pendfunc2): Use FAST_TRACEPOINT_LABEL.
* gdb.trace/trace-break.c: include "trace-common.h", remove SYMBOL
macro.
(func): Remove.
(marker): Use FAST_TRACEPOINT_LABEL.
* gdb.trace/trace-common.h: New header.
* gdb.trace/trace-condition.c: include "trace-common.h", remove SYMBOL
macro.
(func): Remove.
(marker): Use FAST_TRACEPOINT_LABEL.
* gdb.trace/trace-mt.c: include "trace-common.h", remove SYMBOL macro.
(func): Remove.
(thread_function): Use FAST_TRACEPOINT_LABEL.
These casts uses the typedef target type (long int *) instead of the
typedef name. This was a little mistake in one of the big C++ cast
patches.
gdb/ChangeLog:
* inf-ptrace.c (inf_ptrace_fetch_register): Change long int *
cast to PTRACE_TYPE_RET *.
(inf_ptrace_store_register): Likewise.
Switch to using 'add_info' function for creating basic info
sub-commands.
gdb/ChangeLog:
* avr-tdep.c (_initialize_avr_tdep): Switch to 'add_info' for creating
info sub-commands.
* gnu-nat.c (add_task_commands): Likewise.
* macrocmd.c (_initialize_macrocmd): Likewise.
The 'add_info' function is used for creating info commands, these
commands should be created as 'class_info' rather than 'no_class'.
gdb/ChangeLog:
* cli/cli-decode.c (add_info): Switch to class_info.
These variables were used in many gdb.trace tests. Keep them in one place,
to reduce work needed for new targets.
gdb/testsuite/ChangeLog:
* gdb.trace/backtrace.exp: Use global fpreg/spreg definition, add $
in front.
* gdb.trace/change-loc.exp: Use global pcreg definition.
* gdb.trace/collection.exp: Use global pcreg/fpreg/spreg definition.
* gdb.trace/entry-values.exp: Use global spreg definition, add $
in front.
* gdb.trace/mi-trace-frame-collected.exp: Use global pcreg definition.
* gdb.trace/pending.exp: Likewise.
* gdb.trace/report.exp: Use global pcreg/fpreg/spreg definition.
* gdb.trace/trace-break.exp: Likewise.
* gdb.trace/trace-condition.exp: Use global pcreg definition, add $
in front.
* gdb.trace/unavailable.exp: Use global pcreg/fpreg/spreg definition.
* gdb.trace/while-dyn.exp: Use global fpreg definition, add $
in front.
* lib/trace-support.exp: Define fpreg, spreg, pcreg variables.
Consider a function with the following signature...
function F (R : out Rec_Type) return Enum_Type;
... where Rec_Type is a simple record:
type Rec_Type is record
Cur : Integer;
end record;
Trying to "finish" from that function causes GDB to SEGV:
(gdb) fin
Run till exit from #0 bar.f (r=...) at bar.adb:5
0x00000000004022fe in foo () at foo.adb:5
5 I : Enum_Type := F (R);
[1] 18949 segmentation fault (core dumped) /[..]/gdb
This is related to the fact that funtion F has a parameter (R)
which is an "out" parameter being passed by copy. For those,
GNAT transforms the return value to be a record with multiple
fields: The first one is called "RETVAL" and contains the return
value shown in the source, and the remaining fields have the same
name as the "out" or "in out" parameters which are passed by copy.
So, in the example above, function F returns a struct that has
one field who name is "r".
Because "RETVAL" starts with "R", GDB thinks it's a wrapper field,
because it looks like the encoding used for variant records:
-- member_name ::= {choice} | others_choice
-- choice ::= simple_choice | range_choice
-- simple_choice ::= S number
-- range_choice ::= R number T number <<<<<----- here
-- number ::= {decimal_digit} [m]
-- others_choice ::= O (upper case letter O)
See ada_is_wrapper_field:
return (name != NULL
&& (startswith (name, "PARENT")
|| strcmp (name, "REP") == 0
|| startswith (name, "_parent")
|| name[0] == 'S' || name[0] == 'R' || name[0] == 'O'));
As a result of this, when trying to print the RETURN value,
we think that RETVAL is a wrapper, and thus recurse into
print_field_values...
if (ada_is_wrapper_field (type, i))
{
comma_needed =
print_field_values (TYPE_FIELD_TYPE (type, i),
valaddr,
(offset
+ TYPE_FIELD_BITPOS (type, i) / HOST_CHAR_BIT),
stream, recurse, val, options,
comma_needed, type, offset, language);
... which is a problem since print_field_values assumes that
the type it is given ("TYPE_FIELD_TYPE (type, i)" here), is also
a record type. However, that's not the case, since RETVAL is
an enum. That eventually leads GDB to a NULL type when trying to
extract fields out of the enum, which then leads to a SEGV when
trying to dereference it.
Ideally, we'd want to be a little more careful in identifying
wrapper fields, by enhancing ada_is_wrapper_field to be a little
more complete in its analysis of the field name before declaring
it a variant record wrapper. However, it's not super easy to do
so, considering that the choices can be combined together when
complex choices are used. Eg:
-- [...] the choice 1 .. 4 | 7 | -10 would be represented by
-- R1T4S7S10m
Given that we are working towards getting rid of GNAT encodings,
which means that the above will eventually disappear, we took
the more pragmatic approach is just treating RETVAL as a special
case.
gdb/ChangeLog:
* ada-lang.c (ada_is_wrapper_field): Add special handling
for fields called "RETVAL".
gdb/testsuite/ChangeLog:
* gdb.ada/fin_fun_out: New testcase.
We've already has the definition like this,
#define ELF_STRING_ARM_unwind ".ARM.exidx"
so it is better to use the macro rather than the string.
gdb:
2015-11-09 Yao Qi <yao.qi@linaro.org>
* arm-tdep.c (arm_exidx_new_objfile): Use
ELF_STRING_ARM_unwind.
This patch adds a new function displaced_step_in_progress_thread,
which returns whether the thread is in progress of displaced
stepping.
gdb:
2015-11-09 Yao Qi <yao.qi@linaro.org>
* infrun.c (displaced_step_in_progress_thread): New function.
(handle_inferior_event_1): Call it.
Some of the source code for the test cases in the GDB testsuite
reside in .S files containing assembly code. These files typically
define a symbol - such as main - which may, depending on the target,
require a prefix such as underscore.
For example, gdb.dwarf2/dw-compdir-oldgcc.S defines the symbol main:
main: .globl main
Some targets, such as rx-elf, require main to have an underscore
prefix. (If it doesn't, a linker error results due to not being able
to find _main required by crt0.o.) So, instead, the above should look
like this for rx-elf and other targets with this same requirement:
_main: .globl _main
This patch defines a new tcl proc in lib/gdb named
gdb_target_symbol_prefix_flags_asm. This proc returns a string
which will - assuming everything else is wired up correctly - cause
-DSYMBOL_PREFIX=_ to be passed on the command line to the compiler.
The test cases are augmented with a macro definition for SYMBOL
as follows:
#define CONCAT1(a, b) CONCAT2(a, b)
#define CONCAT2(a, b) a ## b
#ifdef SYMBOL_PREFIX
# define SYMBOL(str) CONCAT1(SYMBOL_PREFIX, str)
#else
# define SYMBOL(str) str
#endif
Symbols, such as main shown in the example earlier are then wrapped
with SYMBOL like this:
SYMBOL(main): .globl SYMBOL(main)
The net effect will be to add a prefix for those targets which need
it and add no prefix for those targets which do not.
It should be noted that there was already a proc in lib/gdb.exp
called gdb_target_symbol_prefix_flags. It still exists, but has
been significantly rewritten. (There is only one small difference
between the two versions.)
That proc used to explicitly list targets which were known to
require an underscore prefix. This is no longer done; the recently
added proc, gdb_target_symbol_prefix, is now invoked to dynamically
discover whether or not a prefix is required for that particular
target.
The difference between gdb_target_symbol_prefix_flags_asm
and gdb_target_symbol_prefix_flags is that the former returns
a bare prefix while the latter returns the prefix enclosed in
double quotes. I.e. assuming that the discovered prefix is
underscore, gdb_target_symbol_prefix_flags_asm returns:
additional_flags=-DSYMBOL_PREFIX=_
while gdb_target_symbol_prefix_flags returns:
additional_flags=-DSYMBOL_PREFIX="_"
The double-quoted version is not suitable for using with .S files
containing assembly code; there is no way to strip the double quotes
using C preprocessor constructs.
It would be possible to use the bare (non double quoted) version in
C source code. However, the supporting macros become more complicated
and therefore more difficult to maintain.
gdb/testsuite/ChangeLog:
* lib/gdb (gdb_target_symbol_prefix_flags_asm): New proc.
(gdb_target_symbol_prefix_flags): Define in terms of _asm
version.
* gdb.arch/i386-float.exp, gdb.arch/i386-permbkpt.exp,
gdb.dwarf2/dw2-canonicalize-type.exp,
gdb.dwarf2/dw2-compdir-oldgcc.exp, gdb.dwarf2/dw2-minsym-in-cu.exp,
gdb.dwarf2/dw2-op-stack-value.exp, gdb.dwarf2/dw2-unresolved.exp,
gdb.dwarf2/fission-reread.exp, gdb.dwarf2/pr13961.exp: Use flags
provided by gdb_target_symbol_prefix_flags_asm.
* gdb.dwarf2/dw2-canonicalize-type.S, gdb.dwarf2/dw2-compdir-oldgcc.S,
testsuite/gdb.dwarf2/dw2-minsym-in-cu.S,
testsuite/gdb.dwarf2/dw2-unresolved-main.c,
testsuite/gdb.dwarf2/dw2-unresolved.S, gdb.dwarf2/fission-reread.S,
gdb.dwarf2/pr13961.S: Define and use SYMBOL macro (and supporting
macros where needed). Use this macro for symbols which require
the prefix provided by SYMBOL_PREFIX.
Some of the tests in gdb.dwarf2 which use Dwarf::assemble refer to
(minimal/linker) symbols created in the course of building a small
test program. Some targets use a prefix such as underscore ("_") on
these symbols. Many of the tests in gdb.dwarf2 do not take this into
account. As a consequence, these tests fail to build, resulting
either in failures or untested testcases.
Here is an example from gdb.dwarf2/dw2-regno-invalid.exp:
Dwarf::assemble $asm_file {
cu {} {
compile_unit {
{low_pc main DW_FORM_addr}
{high_pc main+0x10000 DW_FORM_addr}
} {
...
}
For targets which require an underscore prefix on linker symbols,
the two occurrences of "main" would have to have a prepended underscore,
i.e. _main instead of main.
For the above case, a call to the new proc gdb_target_symbol is used
prepend the correct prefix to the symbol. I.e. the above code is
rewritten (as shown in the patch) as follows:
Dwarf::assemble $asm_file {
cu {} {
compile_unit {
{low_pc [gdb_target_symbol main] DW_FORM_addr}
{high_pc [gdb_target_symbol main]+0x10000 DW_FORM_addr}
} {
...
}
I also found it necessary to make an adjustment to lib/dwarf.exp so that
expressions of more than just one list element can be used in DW_TAG_...
constructs. Both atomic-type.exp and dw2-bad-mips-linkage-name.exp require
this new functionality.
gdb/testsuite/ChangeLog:
* lib/gdb.exp (gdb_target_symbol_prefix, gdb_target_symbol):
New procs.
* lib/dwarf.exp (_handle_DW_TAG): Handle attribute values,
representing expressions, of more than one list element.
* gdb.dwarf2/atomic-type.exp (Dwarf::assemble): Use gdb_target_symbol
to prepend linker symbol prefix to f.
* gdb.dwarf2/data-loc.exp (Dwarf::assemble): Likewise, for
table_1 and table_2.
* gdb.dwarf2/dw2-bad-mips-linkage-name.exp (Dwarf::assemble):
Likewise, for f and g.
* gdb.dwarf2/dw2-ifort-parameter.exp (Dwarf::assemble): Likewise,
for ptr.
* gdb.dwarf2/dw2-regno-invalid.exp (Dwarf::assemble): Likewise,
for main.
* gdb.dwarf2/dynarr-ptr.exp (Dwarf::assemble): Likewise, for
table_1_ptr and table_2_ptr.
gdb:
2015-11-05 Yao Qi <yao.qi@linaro.org>
* aarch64-tdep.c (aarch64_displaced_step_copy_insn): Call
aarch64_decode_insn and decode instruction by aarch64_inst.
This patch convert aarch64_analyze_prologue to using aarch64_decode_insn
to decode instructions. After this change, aarch64_analyze_prologue
looks much simple, and some aarch64_decode_* functions are removed
accordingly.
gdb:
2015-11-05 Yao Qi <yao.qi@linaro.org>
* aarch64-tdep.c (extract_signed_bitfield): Remove.
(decode_masked_match): Remove.
(aarch64_decode_add_sub_imm): Remove.
(aarch64_decode_br): Remove.
(aarch64_decode_eret): Remove.
(aarch64_decode_movz): Remove.
(aarch64_decode_orr_shifted_register_x): Remove.
(aarch64_decode_ret): Remove.
(aarch64_decode_stp_offset): Remove.
(aarch64_decode_stur): Remove.
(aarch64_analyze_prologue): Call aarch64_decode_insn
and use aarch64_inst to decode instructions.
This patch combines both aarch64_decode_stp_offset_wb and
aarch64_decode_stp_offset together.
gdb:
2015-11-05 Yao Qi <yao.qi@linaro.org>
* aarch64-tdep.c (aarch64_decode_stp_offset): New argument
wback.
(aarch64_decode_stp_offset_wb): Removed.
(aarch64_analyze_prologue): Don't use
aarch64_decode_stp_offset_wb.
allocate (vla1 (5)) ! vla1-not-allocated
l = allocated(vla1) ! vla1-allocated <------------------
Expecting: ^(510-data-evaluate-expression vla1[^M
]+)?(510\^done,value="\(0, 0, 0, 0, 0\)"[^M
]+[(]gdb[)] ^M
[ ]*)
510-data-evaluate-expression vla1^M
510^done,value="(1.82987403e-09, 7.8472714e-44, 1.82987403e-09, 7.8472714e-44, 2.67929926e+20)"^M
(gdb) ^M
FAIL: gdb.mi/mi-vla-fortran.exp: evaluate allocated vla
gcc-4.9.2-6.fc21.x86_64
I think some older gfortran did initialize allocated memory but that is an
unspecified behavior. I haven't found any initialization mentioned
in Fortran 90 standard (draft) and it is also clearly stated here:
https://software.intel.com/en-us/forums/intel-fortran-compiler-for-linux-and-mac-os-x/topic/268786
Initialization to 0 of allocated arrays (of integers) is an
implementation issue. i.e. do not rely on it.
Joel Brobecker wrote:
I am wondering if it might be better to just relax instead the regexp to allow
any number rather than just remove the test altogether. The test allows us to
verify that, as soon as we're past the "allocate" call, we no longer say "not
allocated".
gdb/testsuite/ChangeLog
2015-11-03 Jan Kratochvil <jan.kratochvil@redhat.com>
Joel Brobecker <brobecker@adacore.com>
* gdb.mi/mi-vla-fortran.exp (evaluate allocated vla): Permit any data.
This is needed to avoid O(n**2) complexity when recording MVCLE and other
partial execution instructions.
gdb/ChangeLog:
PR/18376
* gdb/s390-linux-tdep.c (s390_is_partial_instruction): New function.
(s390_software_single_step): New function.
(s390_displaced_step_hw_singlestep): New function.
(s390_gdbarch_init): Fill gdbarch slots with the above.
gdb/ChangeLog:
PR/18376
* gdb/configure.tgt: Add linux-record.o to s390*-linux.
* gdb/s390-linux-tdep.c: #include "linux-record.h", "record-full.h"
(s390_linux_record_tdep): New static global variable.
(s390x_linux_record_tdep): New static global variable.
(s390_all_but_pc_registers_record): New function.
(s390_canonicalize_syscall): New function.
(s390_linux_syscall_record): New function.
(s390_linux_record_signal): New function.
(s390_record_calc_disp_common): New function.
(s390_record_calc_disp): New function.
(s390_record_calc_disp_vsce): New function.
(s390_record_calc_rl): New function.
(s390_record_gpr_g): New function.
(s390_record_gpr_h): New function.
(s390_record_vr): New function.
(s390_process_record): New function.
(s390_init_linux_record_tdep): New function.
(s390_gdbarch_init): Fill record function slots.
gdb/testsuite/ChangeLog:
* gdb.reverse/s390-mvcle.c: New test.
* gdb.reverse/s390-mvcle.exp: New file.
* lib/gdb.exp: Enable reverse tests on s390*-linux.
On the newly added s390 target, it's possible for a single instruction
to write practically unbounded amount of memory (eg. MVCLE). This caused
a stack overflow when alloca was used.
gdb/ChangeLog:
* record-full.c (record_full_exec_insn): Use xmalloc for temporary
memory storage.
The breakpoint presented in the return statement was not activated while
compiling the test with gcc 4.9.2. Added a dummy statement to allow the
breakpoint again.
2015-10-14 Walfred Tedeschi <walfred.tedeschi@intel.com>
gdb/testsuite:
* i386-mpx-map.c (foo): Add dummy statement to trigger breakpoint.
Change-Id: I5293ca1c7f82a631e1e41cb650c30dd2d09ef3c2
Signed-off-by: Walfred Tedeschi <walfred.tedeschi@intel.com>
Adapts tests to use actual GCC flags, previous used flags were
related to an internal GCC release.
2015-06-18 Walfred Tedeschi <walfred.tedeschi@intel.com>
gdb/testsuite:
* gdb.arch/i386-mpx-map.exp (comp_flags): Use released GCC flags.
* gdb.arch/i386-mpx.exp (comp_flags): Use released GCC flags.
Change-Id: Id4c4551693a8df071ed4b71bb5dfb46a526ed5db
Signed-off-by: Walfred Tedeschi <walfred.tedeschi@intel.com>
Error was introduced to fix a build issue caused by a mismatching variable
size. The error message is changed to explicitly report what goes wrong
and how user might still investigate the issue.
2015-06-18 Walfred Tedeschi <walfred.tedeschi@intel.com>
* i386-tdep.c (i386_mpx_get_bt_entry) Improves error message.
Change-Id: I6e9c7475eba663f49bd8e720b84ad0265bcb0e92
Signed-off-by: Walfred Tedeschi <walfred.tedeschi@intel.com>
Add support for the /s modifier of the "record instruction-history" command. It
behaves exactly like /m and prints disassembled instructions in the order in
which they were recorded with interleaved sources. We accept /s in addition
to /m to align with the "disassemble" command.
The "record instruction-history" modifiers were not documented. Document
all of them.
gdb/
* record.c (get_insn_history_modifiers): Set DISASSEMBLY_SOURCE
instead of DISASSEMBLY_SOURCE_DEPRECATED. Also accept /s.
(_initialize_record): Document the /s modifier.
* NEWS: Announce record instruction-history's new /s modifier.
doc/
* gdb.texinfo (Process Record and Replay): Document "record
instruction-history" modifiers.
The /m modifier interleaves source lines with the disassembly of recorded
instructions. This calls disasm.c's gdb_disassembly once for each recorded
instruction to be printed.
This doesn't really work because gdb_disassembly may choose not to print
anything in some situations. And if it does print something, the output
interferes with btrace_insn_history's output around it.
It further results in a separate asm_insns list for each instruction in MI.
Even though there is no MI support for target record, yet, we fix this obvious
issue.
Change record instruction-history /m to use the new gdb_pretty_print_insn
function for printing a single instruction and interleave source lines as
appropriate.
We cannot reuse the new disasm.c do_mixed_source_and_assembly function without
significant changes to it.
gdb/
* record-btrace.c (struct btrace_line_range): New.
(btrace_mk_line_range, btrace_line_range_add)
(btrace_line_range_is_empty, btrace_line_range_contains_range)
(btrace_find_line_range, btrace_print_lines): New.
(btrace_insn_history): Add source interleaving algorithm.
The "record instruction-history" command prints for each instruction in
addition to the instruction's disassembly:
- the instruction number in the recorded execution trace
- a '?' before the instruction if it was executed speculatively
To allow the "record instruction-history" command to use GDB's disassembly
infrastructure, we extend gdb_pretty_print_insn to optionally print those
additional fields and export the function.
Add a new struct disasm_insn to add additional fields describing the
to-be-disassembled instruction. The additional fields are:
number an optional instruction number, zero if omitted.
is_speculative a predicate saying whether the instruction was
executed speculatively.
If non-zero, the instruction number is printed first. It will also appear
as a new optional field "insn-number" in MI. The field will be present if
insn_num is non-zero.
If is_speculative is set, speculative execution will be indicated by a "?"
following the new instruction number field. Unless the PC is omitted, it
will overwrite the first byte of the PC prefix. It will appear as a new
optional field "is-speculative" in MI. The field will contain "?" and will
be present if is_speculative is set.
The speculative execution indication is guarded by a new flag
DISASSEMBLY_SPECULATION.
Replace the PC parameter of gdb_pretty_print_insn with a pointer to the above
struct. GDB's "disassemble" command does not use the new fields.
gdb/
* disasm.h (DISASSEMBLY_SPECULATION): New.
(struct disasm_insn): New.
(gdb_pretty_print_insn): New.
* disasm.c (gdb_pretty_print_insn): Replace parameter PC with INSN.
Update users. Print instruction number and indicate speculative
execution, if requested.
Split disasm.c's dump_insn into two parts:
- print a single instruction
- loop over the specified address range
The first part will be refined in subsequent patches so it can be reused.
gdb/
* disasm.c (dump_insns): Split into this and ...
(gdb_pretty_print_insn): ... this.
This actually fixes the build in C:
/home/simark/src/binutils-gdb/gdb/xtensa-linux-nat.c💯1: error: no previous prototype for ‘supply_gregset_reg’ [-Werror=missing-prototypes]
supply_gregset_reg (struct regcache *regcache,
^
/home/simark/src/binutils-gdb/gdb/xtensa-linux-nat.c:257:1: error: no previous prototype for ‘xtensa_linux_fetch_inferior_registers’ [-Werror=missing-prototypes]
xtensa_linux_fetch_inferior_registers (struct target_ops *ops,
^
/home/simark/src/binutils-gdb/gdb/xtensa-linux-nat.c:272:1: error: no previous prototype for ‘xtensa_linux_store_inferior_registers’ [-Werror=missing-prototypes]
xtensa_linux_store_inferior_registers (struct target_ops *ops,
^
cc1: all warnings being treated as errors
These functions are local to this file, so they should be static.
gdb/ChangeLog:
* xtensa-linux-nat.c (supply_gregset_reg): Make static.
(xtensa_linux_fetch_inferior_registers): Likewise.
(xtensa_linux_store_inferior_registers): Likewise.
Fixes
/home/simark/src/binutils-gdb/gdb/gdbserver/linux-mips-low.c: In function ‘void mips_add_watchpoint(arch_process_info*, CORE_ADDR, int, int)’:
/home/simark/src/binutils-gdb/gdb/gdbserver/linux-mips-low.c:368:19: error: invalid conversion from ‘int’ to ‘target_hw_bp_type’ [-fpermissive]
new_watch->type = watch_type;
^
gdb/gdbserver/ChangeLog:
* linux-mips-low.c (mips_linux_new_thread): Change type of
watch_type to enum target_hw_bp_type.
Trivial casts for C++.
Fixes things like
In file included from /home/simark/src/binutils-gdb/gdb/gdbserver/../common/common-defs.h:39:0,
from /home/simark/src/binutils-gdb/gdb/gdbserver/server.h:22,
from /home/simark/src/binutils-gdb/gdb/gdbserver/linux-arm-low.c:19:
/home/simark/src/binutils-gdb/gdb/gdbserver/linux-arm-low.c: In function ‘int arm_get_hwcap(long unsigned int*)’:
/home/simark/src/binutils-gdb/gdb/gdbserver/../../include/libiberty.h:711:38: error: invalid conversion from ‘void*’ to ‘unsigned char*’ [-fpermissive]
# define alloca(x) __builtin_alloca(x)
^
/home/simark/src/binutils-gdb/gdb/gdbserver/linux-arm-low.c:807:25: note: in expansion of macro ‘alloca’
unsigned char *data = alloca (8);
^
gdb/gdbserver/ChangeLog:
* linux-aarch32-low.c (arm_fill_gregset): Add cast.
(arm_store_gregset): Likewise.
* linux-arm-low.c (arm_get_hwcap): Likewise.
(arm_read_description): Likewise.
Mostly some casts from "generic arg" void* to the actual type.
There are two (enum gdb_signal) casts. I tried to see if it would have
been better to change the type of sigrc, but it has a double role, as an
enum and as an integer, so I left it as is.
gdb/ChangeLog:
* remote-sim.c (check_for_duplicate_sim_descriptor): Add casts.
(get_sim_inferior_data): Likewise.
(sim_inferior_data_cleanup): Likewise.
(gdbsim_close_inferior): Likewise.
(gdbsim_resume_inferior): Likewise.
(gdbsim_wait): Likewise.
(simulator_command): Likewise.
(sim_command_completer): Likewise.
g++ doesn't like that we forward-declare a variable that is initialized
later in the file. It's easy enough to re-order things to fix it.
Fixes
/home/simark/src/binutils-gdb/gdb/gdbserver/linux-ppc-low.c:663:28: error: redefinition of ‘usrregs_info ppc_usrregs_info’
static struct usrregs_info ppc_usrregs_info =
^
/home/simark/src/binutils-gdb/gdb/gdbserver/linux-ppc-low.c:381:28: note: ‘usrregs_info ppc_usrregs_info’ previously declared here
static struct usrregs_info ppc_usrregs_info;
^
gdb/gdbserver/ChangeLog:
* linux-ppc-low.c (ppc_usrregs_info): Remove
forward-declaration.
(ppc_arch_setup): Move lower in file.
continue_to_breakpoint always continues to the next breakpoint, not to the
one named in parameter. This rendered the tests effectively useless, since
marker2 was never reached.
gdb/testsuite/ChangeLog:
* gdb.reverse/fstatat-reverse.exp: Set breakpoint on marker1 after
reaching marker2.
* gdb.reverse/getresuid-reverse.exp: Likewise.
* gdb.reverse/pipe-reverse.exp: Likewise.
* gdb.reverse/readv-reverse.exp: Likewise.
* gdb.reverse/recvmsg-reverse.exp: Likewise.
* gdb.reverse/time-reverse.exp: Likewise.
* gdb.reverse/waitpid-reverse.exp: Likewise and add KFAILs.
Assuming displaced stepping is enabled, and a breakpoint is set in the
memory region of the scratch pad, things break. One of two cases can
happen:
#1 - The breakpoint wasn't inserted yet (all threads were stopped), so
after setting up the displaced stepping scratch pad with the
adjusted copy of the instruction we're trying to single-step, we
insert the breakpoint, which corrupts the scratch pad, and the
inferior executes the wrong instruction. (Example below.)
This is clearly unacceptable.
#2 - The breakpoint was already inserted, so setting up the displaced
stepping scratch pad overwrites the breakpoint. This is OK in
the sense that we already assume that no thread is going to
executes the code in the scratch pad range (after initial
startup) anyway.
This commit addresses both cases by simply punting on displaced
stepping if we have a breakpoint in the scratch pad range.
The #1 case above explains a few regressions exposed by the AS/NS
series on x86:
Running ./gdb.dwarf2/callframecfa.exp ...
FAIL: gdb.dwarf2/callframecfa.exp: set display for call-frame-cfa
FAIL: gdb.dwarf2/callframecfa.exp: step 1 for call-frame-cfa
FAIL: gdb.dwarf2/callframecfa.exp: step 2 for call-frame-cfa
FAIL: gdb.dwarf2/callframecfa.exp: step 3 for call-frame-cfa
FAIL: gdb.dwarf2/callframecfa.exp: step 4 for call-frame-cfa
Running ./gdb.dwarf2/typeddwarf.exp ...
FAIL: gdb.dwarf2/typeddwarf.exp: continue to breakpoint: continue to typeddwarf.c:53
FAIL: gdb.dwarf2/typeddwarf.exp: check value of x at typeddwarf.c:53
FAIL: gdb.dwarf2/typeddwarf.exp: check value of y at typeddwarf.c:53
FAIL: gdb.dwarf2/typeddwarf.exp: check value of z at typeddwarf.c:53
FAIL: gdb.dwarf2/typeddwarf.exp: continue to breakpoint: continue to typeddwarf.c:73
FAIL: gdb.dwarf2/typeddwarf.exp: check value of w at typeddwarf.c:73
FAIL: gdb.dwarf2/typeddwarf.exp: check value of x at typeddwarf.c:73
FAIL: gdb.dwarf2/typeddwarf.exp: check value of y at typeddwarf.c:73
FAIL: gdb.dwarf2/typeddwarf.exp: check value of z at typeddwarf.c:73
Enabling "maint set target-non-stop on" implies displaced stepping
enabled as well, and it's the latter that's to blame here. We can see
the same failures with "maint set target-non-stop off + set displaced
on".
Diffing (good/bad) gdb.log for callframecfa.exp shows:
@@ -99,29 +99,29 @@ Breakpoint 2 at 0x80481b0: file q.c, lin
continue
Continuing.
-Breakpoint 2, func (arg=77) at q.c:2
+Breakpoint 2, func (arg=52301) at q.c:2
2 in q.c
(gdb) PASS: gdb.dwarf2/callframecfa.exp: continue to breakpoint: continue to breakpoint for call-frame-cfa
display arg
-1: arg = 77
-(gdb) PASS: gdb.dwarf2/callframecfa.exp: set display for call-frame-cfa
+1: arg = 52301
+(gdb) FAIL: gdb.dwarf2/callframecfa.exp: set display for call-frame-cfa
The problem is here, when setting up the func call:
Breakpoint 1, main (argc=-13345, argv=0x0) at q.c:7
7 in q.c
(gdb) disassemble
Dump of assembler code for function main:
0x080481bb <+0>: push %ebp
0x080481bc <+1>: mov %esp,%ebp
0x080481be <+3>: sub $0x4,%esp
=> 0x080481c1 <+6>: movl $0x4d,(%esp)
0x080481c8 <+13>: call 0x80481b0 <func>
0x080481cd <+18>: leave
0x080481ce <+19>: ret
End of assembler dump.
(gdb) disassemble /r
Dump of assembler code for function main:
0x080481bb <+0>: 55 push %ebp
0x080481bc <+1>: 89 e5 mov %esp,%ebp
0x080481be <+3>: 83 ec 04 sub $0x4,%esp
=> 0x080481c1 <+6>: c7 04 24 4d 00 00 00 movl $0x4d,(%esp)
0x080481c8 <+13>: e8 e3 ff ff ff call 0x80481b0 <func>
0x080481cd <+18>: c9 leave
0x080481ce <+19>: c3 ret
End of assembler dump.
Note the breakpoint at main is set at 0x080481c1. Right at the
instruction that sets up func's argument. Executing that instruction
should write 0x4d to the address pointed at by $esp. However, if we
stepi, the program manages to write 52301/0xcc4d there instead (0xcc
is int3, the x86 breakpoint instruction), because the breakpoint
address is 4 bytes inside the scratch pad location, which is
0x080481bd:
(gdb) p 0x080481c1 - 0x080481bd
$1 = 4
IOW, instead of executing:
"c7 04 24 4d 00 00 00" [ movl $0x4d,(%esp) ]
the inferior executes:
"c7 04 24 4d cc 00 00" [ movl $0xcc4d,(%esp) ]
gdb/ChangeLog:
2015-10-30 Pedro Alves <palves@redhat.com>
* breakpoint.c (breakpoint_in_range_p)
(breakpoint_location_address_range_overlap): New functions.
* breakpoint.h (breakpoint_in_range_p): New declaration.
* infrun.c (displaced_step_prepare_throw): If there's a breakpoint
in the scratch pad range, don't displaced step.
Nowadays, test gdb.threads/wp-replication.exp uses a while loop to
repeatedly insert HW watchpoint, resume and check no error message
coming out, in order to count HW watchpoints There are some
drawbacks in this way,
- the loop could be endless. I think this is use to making trouble
to S/390, since we had such comment
# Some targets (like S/390) behave as though supporting
# unlimited hardware watchpoints. In this case we just take a
# safe exit out of the loop.
I hit this today too because a GDB internal error is triggered
on "continue" in the loop, and $done is 0 invariantly, so the loop
can't end.
- the code counting hardware watchpoint is too complicated. We can
use "set breakpoint always-inserted on" to get the result of inserting
HW watchpoint without resuming the inferior. In this way,
watch_count_done and empty_cycle in c file is no longer needed.
In this patch, I change to use "set breakpoint always-inserted on" trick,
and only iterate $NR_THREADS times, to count the HW watchpoint. In this
way, the loop can't be endless, and GDB doesn't need to resume the inferior.
gdb/testsuite:
2015-10-30 Yao Qi <yao.qi@linaro.org>
* gdb.threads/wp-replication.c (watch_count_done): Remove.
(empty_cycle): Remove.
(main): Don't call empty_cycle. Don't use watch_count_done.
* gdb.threads/wp-replication.exp: Don't set breakpoint on
empty_cycle. Rewrite the code counting HW watchpoints.
60 bytes is the size of glibc's struct termios, the one used by kernel is
36 bytes long.
gdb/ChangeLog:
* aarch64-linux-tdep.c (aarch64_linux_init_abi): Fix size_termios.
* amd64-linux-tdep.c (amd64_linux_init_abi): Fix size_termios.
(amd64_x32_linux_init_abi): Fix size_termios.
We have to use extract_unsigned_integer to read paramaters structure - target
pointers can have different endianness and size.
gdb/ChangeLog:
* linux-record.c (record_linux_system_call): Fix old_select.
Memory size for getgroups16 needs to be multiplied by entry count, and only
needs recording if the pointer is non-NULL. setgroups16, on the other hand,
doesn't write to user memory and doesn't need special handling at all.
gdb/ChangeLog:
* linux-record.c (record_linux_system_call): Fix [gs]etgroups16.
The code failed to account for padding between the int and subsequent
pointer present on 64-bit architectures.
gdb/ChangeLog:
* linux-record.c (record_linux_msghdr): Fix msg_namelen handling.
getdents buffer size is given in bytes, not dirent entries (which have
variable size anyway). We don't need size_dirent and size_dirent64 for
this reason.
readdir, on the other hand, needs size of old_linux_dirent, which is
a somewhat different structure. Accordingly, rename size_dirent
to size_old_dirent.
gdb/ChangeLog:
* aarch64-linux-tdep.c (aarch64_linux_init_abi): Remove
size_dirent{,64}, add size_old_dirent.
* amd64-linux-tdep.c (amd64_linux_init_abi): Remove size_dirent{,64},
add size_old_dirent.
(amd64_x32_linux_init_abi): Remove size_dirent{,64}, add
size_old_dirent.
* arm-linux-tdep.c (arm_linux_init_abi): Remove size_dirent{,64},
add size_old_dirent.
* i386-linux-tdep.c (i386_linux_init_abi): Remove size_dirent{,64},
add size_old_dirent.
* linux-record.c (record_linux_system_call): Fix handling of readdir
and getdents{,64}.
* linux-record.h (struct linux_record_tdep): Remove size_dirent{,64},
add size_old_dirent.
* ppc-linux-tdep.c (ppc_init_linux_record_tdep): Remove
size_dirent{,64}, add size_old_dirent.
i386 and arm wrongly set them to 2, when it should be 4. size_[ug]id is used
by getgroups32 etc syscalls, while size_old_[ug]id is used for getgroups16
and friends.
gdb/ChangeLog:
* arm-linux-tdep.c (arm_linux_init_abi): Fix size_[ug]id.
* i386-linux-tdep.c (i386_linux_init_abi): Fix size_[ug]id.
gdb/testsuite/ChangeLog:
* gdb.reverse/fstatat-reverse.c: New test.
* gdb.reverse/fstatat-reverse.exp: New file.
* gdb.reverse/getresuid-reverse.c: New test.
* gdb.reverse/getresuid-reverse.exp: New file.
* gdb.reverse/pipe-reverse.c: New test.
* gdb.reverse/pipe-reverse.exp: New file.
* gdb.reverse/readv-reverse.c: New test.
* gdb.reverse/readv-reverse.exp: New file.
* gdb.reverse/recvmsg-reverse.c: New test.
* gdb.reverse/recvmsg-reverse.exp: New file.
* gdb.reverse/time-reverse.c: New test.
* gdb.reverse/time-reverse.exp: New file.
* gdb.reverse/waitpid-reverse.c: New test.
* gdb.reverse/waitpid-reverse.exp: New file.
Fixes on i386:
../../../binutils-gdb/gdb/gdbserver/proc-service.c: In function ps_pdread:
../../../binutils-gdb/gdb/gdbserver/proc-service.c:83:25: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
../../../binutils-gdb/gdb/gdbserver/proc-service.c: In function ps_pdwrite:
../../../binutils-gdb/gdb/gdbserver/proc-service.c:93:30: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
I could have kept both casts:
(CORE_ADDR) (uintptr_t) addr
but it's cleaner this way. The uintptr_t implicitely gets promoted to a
CORE_ADDR, which is at least as long as uintptr_t.
gdb/gdbserver/ChangeLog:
* proc-service.c (ps_pdread): Change CORE_ADDR cast to uintptr_t.
(ps_pdwrite): Likewise.
gdb/gdbserver/ChangeLog:
* linux-arm-low.c (arm_new_thread): Move pointer dereference
to after assert checks.
Signed-off-by: Henrik Wallin <henrik.wallin@windriver.com>
The casts are required because ps_pd{read,write} must respect a fixed
interface.
gdb/gdbserver/ChangeLog:
* proc-service.c (ps_pdread): Add/adjust casts.
(ps_pdwrite): Add/adjust casts.
This fixes this error in C++ mode:
/home/pedro/gdb/mygit/cxx-convertion/src/gdb/mdebugread.c:654:11: error: invalid conversion from ‘int’ to ‘address_class’ [-fpermissive]
theclass = mdebug_register_index;
^
The "theclass" local is of type enum address_class, however, what it
really holds is an address class index. Class index values by design
match the address class values up until LOC_FINAL_VALUE, but extend
beyond that, so it's not really right to store an address class index
in an enum address_class.
The fix is really the same making the 'theclass' local be of type int,
but while we're at it, we get rid of the goto, and thus the local
becomes the 'aclass_index' parameter in the new add_data_symbol
function.
gdb/ChangeLog:
2015-10-29 Pedro Alves <palves@redhat.com>
* mdebugread.c (add_data_symbol): New function, factored out from
...
(parse_symbol): ... here. Delete 'theclass' local.
We could change the signature of the function. However, it would
require changing gdb_target_read in jit-reader.h, which is an exported
interface. It's probably better to just add a cast in our code than to
break other people's code.
gdb/ChangeLog:
* jit.c (jit_target_read_impl): Add cast.
There is no enum value representing 0. It seems like the value of the
name field is irrelevant here.
gdb/ChangeLog:
* dwarf2read.c (partial_die_full_name): Add cast.
Fixes this in C++:
../../src/gdb/break-catch-sig.c: In function ‘int VEC_gdb_signal_type_iterate(const VEC_gdb_signal_type*, unsigned int, gdb_signal_type*)’:
../../src/gdb/common/vec.h:576:12: error: invalid conversion from ‘int’ to ‘gdb_signal_type {aka gdb_signal}’ [-fpermissive]
*ptr = 0; \
^
../../src/gdb/common/vec.h:417:1: note: in expansion of macro ‘DEF_VEC_FUNC_P’
DEF_VEC_FUNC_P(T) \
^
../../src/gdb/break-catch-sig.c:37:1: note: in expansion of macro ‘DEF_VEC_I’
DEF_VEC_I (gdb_signal_type);
^
I actually carried a different fix in the C++ branch that removed this
assignment and then adjusted all callers that depended on it. The
thinking was that this is for the case where we're returning false,
indicating end of iteration. But that results in a much larger and
tricker patch; looking back it seems quite pointless. I looked at the
history of GCC's C++ conversion and saw that they added this same cast
to their version of vec.h, FWIW. (GCC's vec.h is completely different
nowadays, having been converted to templates meanwhile.)
gdb/ChangeLog:
2015-10-29 Pedro Alves <palves@redhat.com>
* common/vec.h (DEF_VEC_FUNC_P) [iterate]: Cast 0 to type T.
I looked at changing these is_destructor_name/is_constructor_name
interfaces in order to detangle the boolean result from the ctor/dtor
kind return, but then realized that this design goes all the way down
to the libiberty demangler interfaces. E.g, include/demangle.h:
~~~
/* Return non-zero iff NAME is the mangled form of a constructor name
in the G++ V3 ABI demangling style. Specifically, return an `enum
gnu_v3_ctor_kinds' value indicating what kind of constructor
it is. */
extern enum gnu_v3_ctor_kinds
is_gnu_v3_mangled_ctor (const char *name);
enum gnu_v3_dtor_kinds {
gnu_v3_deleting_dtor = 1,
gnu_v3_complete_object_dtor,
gnu_v3_base_object_dtor,
/* These are not part of the V3 ABI. Unified destructors are generated
as a speed-for-space optimization when the -fdeclone-ctor-dtor option
is used, and are always internal symbols. */
gnu_v3_unified_dtor,
gnu_v3_object_dtor_group
};
~~~
libiberty/cp-demangle.c:
~~~
enum gnu_v3_ctor_kinds
is_gnu_v3_mangled_ctor (const char *name)
{
enum gnu_v3_ctor_kinds ctor_kind;
enum gnu_v3_dtor_kinds dtor_kind;
if (! is_ctor_or_dtor (name, &ctor_kind, &dtor_kind))
return (enum gnu_v3_ctor_kinds) 0;
return ctor_kind;
}
~~~
etc.
gdb/ChangeLog:
2015-10-29 Pedro Alves <palves@redhat.com>
* gnu-v2-abi.c (gnuv2_is_destructor_name)
(gnuv2_is_constructor_name): Add casts.
... for C++.
Fixes:
gdb/gdbserver/mem-break.c:204:28: error: invalid conversion from 'int' to 'bkpt_type' [-fpermissive]
gdb/gdbserver/ChangeLog:
2015-10-29 Pedro Alves <palves@redhat.com>
* mem-break.c (Z_packet_to_bkpt_type): Add cast.
... as needed for C++.
tpoint->handle is a generic 'void *' handle.
gdb/gdbserver/ChangeLog:
2015-10-29 Pedro Alves <palves@redhat.com>
* tracepoint.c (clear_installed_tracepoints): Add casts.
This is code parsing RSP signal numbers, checking whether the numbers
are indeed valid/known GDB signals, and then converting to host signal
numbers. I considered adding temporary enum gdb_signal variables
instead, but didn't really like the result.
gdb/gdbserver/ChangeLog:
2015-10-29 Pedro Alves <palves@redhat.com>
* server.c (handle_v_cont, process_serial_event): Add enum
gdb_signal casts to signal parsing code.
Fixes:
../../../src/gdb/gdbserver/linux-low.c: In function ‘int linux_low_read_btrace(btrace_target_info*, buffer*, int)’:
../../../src/gdb/gdbserver/linux-low.c:6827:48: error: invalid conversion from ‘int’ to ‘btrace_read_type’ [-fpermissive]
err = linux_read_btrace (&btrace, tinfo, type);
^
In file included from ../../../src/gdb/gdbserver/linux-low.c:98:0:
../../../src/gdb/gdbserver/../nat/linux-btrace.h:116:26: error: initializing argument 3 of ‘btrace_error linux_read_btrace(btrace_data*, btrace_target_info*, btrace_read_type)’ [-fpermissive]
extern enum btrace_error linux_read_btrace (struct btrace_data *btrace,
^
The cyclic dependency the comment talks about is no longer relevant:
https://sourceware.org/ml/gdb-patches/2015-10/msg00643.html
gdb/gdbserver/ChangeLog:
2015-10-29 Pedro Alves <palves@redhat.com>
* linux-low.c (linux_low_read_btrace): Change type of 'type'
parameter.
* server.c (handle_qxfer_btrace): Change type of 'type'
local.
* target.h (struct target_ops) <read_btrace>: Change type of
'type' parameter. Update comment.
Fixes, in C++ mode:
../../src/gdb/common/common-exceptions.c:23:69: error: invalid conversion from ‘int’ to ‘return_reason’ [-fpermissive]
const struct gdb_exception exception_none = { 0, GDB_NO_ERROR, NULL };
^
(I considered adding an enum value for '0', but the code and comments
around return_reason and its uses explain how 0 is special/internal,
so I'm leaving it be.)
gdb/ChangeLog:
2015-10-29 Pedro Alves <palves@redhat.com>
* common/common-exceptions.c (exception_none): Add cast.
Fixes:
src/gdb/compile/compile-c-types.c:36:12: error: declaration of ‘gcc_type type_map_instance::gcc_type’ [-fpermissive]
gcc_type gcc_type;
^
In file included from src/gdb/../include/gcc-c-interface.h:23:0,
from src/gdb/compile/compile-internal.h:21,
from src/gdb/compile/compile-c-types.c:23:
src/gdb/../include/gcc-interface.h:32:28: error: changes meaning of ‘gcc_type’ from ‘typedef long long unsigned int gcc_type’ [-fpermissive]
typedef unsigned long long gcc_type;
^
src/gdb/compile/compile-c-types.c: In function ‘gcc_type convert_qualified(compile_c_instance*, type*)’:
src/gdb/compile/compile-c-types.c:310:19: error: invalid conversion from ‘int’ to ‘gcc_qualifiers’ [-fpermissive]
quals);
^
gdb/ChangeLog:
2015-10-29 Pedro Alves <palves@redhat.com>
* compile/compile-c-types.c (struct type_map_instance)
<gcc_type>: Rename to gcc_type_handle.
(insert_type, convert_type): Adjust.
In C++, this:
try
{
break;
}
catch (..)
{}
is invalid. However, because our TRY/CATCH macros support it in C,
the C++ version of those macros support it too. To catch such
assumptions, this adds a (disabled) hack that maps TRY/CATCH to raw
C++ try/catch. Then it goes through all instances that building on
x86_64 GNU/Linux trips on, fixing them.
This isn't strictly necessary yet, but I think it's nicer to try to
keep the tree in a state where it's easier to eliminate the TRY/CATCH
macros.
gdb/ChangeLog:
2015-10-29 Pedro Alves <palves@redhat.com>
* dwarf2-frame-tailcall.c (dwarf2_tailcall_sniffer_first): Don't
assume that "break" breaks out of a TRY/CATCH.
* python/py-framefilter.c (py_print_single_arg): Don't assume
"continue" breaks out of a TRY/CATCH.
* python/py-value.c (valpy_binop_throw): New function, factored
out from ...
(valpy_binop): ... this.
(valpy_richcompare_throw): New function, factored
out from ...
(valpy_richcompare): ... this.
* solib.c (solib_read_symbols): Don't assume "break" breaks out
of a TRY/CATCH.
* common/common-exceptions.h [USE_RAW_CXX_TRY]
<TRY/CATCH/END_CATCH>: Define as 1-1 wrappers around try/catch.
A patch (http://sourceware.org/ml/binutils/2015-07/msg00376.html)
submitted to binutils will be encoding move as an 'or' instruction over
[d]addu in assembly and various code stubs. This patch for gdb addresses
that change for the mips specific parts of gdb.
gdb/ChangeLog:
* mips-linux-tdep.c (mips_linux_in_dynsym_stub): Recognise 'or'
as move along with [d]addu.
Nowadays aarch64_decode_insn is a public interface used by both
opcodes and gdb. However, its behaviour relies on a global variable
no_aliases, which isn't a good practise. On the other hand, In default,
no_aliases is zero, but in GDB, we do want no alias when decoding
instructions for prologue analysis (patches to be posted), so that we
can handle both instructions "add" and "mov" (an alias of "add") as
"add". The code in GDB can be simplified.
This patch adds a new argument in aarch64_decode_insn, and pass no_aliases
to it. In GDB side, always pass 1 to it.
include/opcode:
2015-10-28 Yao Qi <yao.qi@linaro.org>
* aarch64.h (aarch64_decode_insn): Update declaration.
opcodes:
2015-10-28 Yao Qi <yao.qi@linaro.org>
* aarch64-dis.c (aarch64_decode_insn): Add one argument
noaliases_p. Update comments. Pass noaliases_p rather than
no_aliases to aarch64_opcode_decode.
(print_insn_aarch64_word): Pass no_aliases to
aarch64_decode_insn.
gdb:
2015-10-28 Yao Qi <yao.qi@linaro.org>
* aarch64-tdep.c (aarch64_software_single_step): Pass 1 to
aarch64_decode_insn.
Fixes a set of errors like:
../../src/gdb/symfile-debug.c: In function ‘int debug_qf_map_symtabs_matching_filename(objfile*, const char*, const char*, int (*)(symtab*, void*), void*)’:
../../src/gdb/symfile-debug.c:137:39: error: invalid conversion from ‘int (*)(symtab*, void*)’ to ‘const void*’ [-fpermissive]
host_address_to_string (callback),
^
Note this has to work with data and function pointers. In C++11 we
may perhaps do something a bit safer, but we're not there yet, and I
don't think it really matters. For now just always do a simple
C-style cast in host_address_to_string itself. No point in adding a
void * cast to each and every caller.
gdb/ChangeLog:
2015-10-27 Pedro Alves <palves@redhat.com>
* common/print-utils.c (host_address_to_string): Rename to ...
(host_address_to_string_1): ... this.
* common/print-utils.h (host_address_to_string): Reimplement as
wrapper around host_address_to_string_1.
* utils.c (gdb_print_host_address): Rename to ...
(gdb_print_host_address_1): ... this.
* utils.h (gdb_print_host_address): Reimplement as wrapper macro
around host_address_to_string_1.
Years ago, these functions used to return errno/EIO. Later, through a
series of changes that intended to remove native/remote differences,
they ended up returning a target_xfer_status in disguise.
Unlike target_xfer_partial&co, the point of target_read_memory&co is
to either fully succeed or fail. On error, they always return
TARGET_XFER_E_IO. So there's no real point in casting the return of
target_read_memory to a target_xfer_status to pass it to memory_error.
Instead, it results in clearer code to simply decouple
target_read_memory&co's return from target_xfer_status.
This fixes build errors like this in C++ mode:
../../src/gdb/corefile.c: In function ‘void read_stack(CORE_ADDR, gdb_byte*, ssize_t)’:
../../src/gdb/corefile.c:276:34: error: invalid conversion from ‘int’ to ‘target_xfer_status’ [-fpermissive]
memory_error (status, memaddr);
^
../../src/gdb/corefile.c:216:1: error: initializing argument 1 of ‘void memory_error(target_xfer_status, CORE_ADDR)’ [-fpermissive]
gdb/ChangeLog:
2015-10-27 Pedro Alves <palves@redhat.com>
* alpha-tdep.c (alpha_read_insn): Always pass TARGET_XFER_E_IO to
memory_error. Rename local 'status' to 'res'.
* c-lang.c (c_get_string): Always pass TARGET_XFER_E_IO to
memory_error.
* corefile.c (read_stack, read_code, write_memory): Always pass
TARGET_XFER_E_IO to memory_error.
* disasm.c (dis_asm_memory_error): Always pass TARGET_XFER_E_IO to
memory_error. Rename parameter 'status' to 'err'.
(dump_insns): Rename local 'status' to 'err'.
* mips-tdep.c (mips_fetch_instruction): Rename parameter 'statusp'
to 'errp'. Rename local 'status' to 'err'. Always pass
TARGET_XFER_E_IO to memory_error.
(mips_breakpoint_from_pc): Rename local 'status' to 'err'.
* target.c (target_read_memory, target_read_raw_memory)
(target_read_stack, target_read_code, target_write_memory)
(target_write_raw_memory): Return -1 on error instead of
TARGET_XFER_E_IO.
* valprint.c (val_print_string): Rename local 'errcode' to 'err'.
Always pass TARGET_XFER_E_IO to memory_error. Update comment.
The documentation of gdbscm_with_guile says that it returns a statically
allocated string (IOW, a const char *). We can reflect that in its
return value type, and get rid of C++ build errors.
Initially fixes:
/home/simark/src/binutils-gdb/gdb/guile/scm-disasm.c: In function ‘void* gdbscm_disasm_read_memory_worker(void*)’:
/home/simark/src/binutils-gdb/gdb/guile/scm-disasm.c:93:12: error: invalid conversion from ‘const void*’ to ‘void*’ [-fpermissive]
return "seek error";
gdb/ChangeLog:
* guile/guile-internal.h (gdbscm_with_guile): Change return
types to const char *.
* guile/scm-safe-call.c (gdbscm_with_guile): Likewise.
(struct c_data) <func>: Likewise.
(struct c_data) <result>: Change type to const char *.
(scscm_eval_scheme_string): Change return type to
const char *.
(scscm_source_scheme_script): Likewise.
(gdbscm_safe_eval_string): Change type of result variable to
const char * and remove cast.
(gdbscm_safe_source_script): Likewise.
* guile/scm-disasm.c (gdbscm_disasm_read_memory_worker):
Change return type to const char *.
(gdbscm_disasm_read_memory): Change type of status to
const char *.
openp's return is documented as:
~~~
If a file is found, return the descriptor.
Otherwise, return -1, with errno set for the last name we tried to open. */
~~~
By inspection, I noticed that there are function calls after the ones
that first set errno, and those may clobber errno. It's safer to save
errno when see an open fail, and restore it on exit.
Tested on x86_64 Fedora 20.
gdb/ChangeLog:
2015-10-27 Pedro Alves <palves@redhat.com>
* source.c (openp): New local 'last_errno'. Use it to
save/restore errno.
This patch was taken directly from Pedro's branch.
Right now, SET_INT32_FIELD is used to set enum fields. This works in C,
but not C++. Therefore, define the new SET_ENUM_FIELD, which casts the
value to the right enum type.
gdb/ChangeLog:
* ctf.c (SET_ENUM_FIELD): New macro.
(ctf_read_status): Use it.
(ctf_read_tp): Use it.
There is a handful of calls to
scm_dynwind_begin (0);
where the parameter is an enum, scm_t_dynwind_flags. In C++, we have no
choice but to add an explicit cast, since there is no enum value that
represents 0 (no flags set).
gdb/ChangeLog:
* guile/scm-breakpoint.c (gdbscm_set_breakpoint_stop_x): Add
scm_t_dynwind_flags casts.
* guile/scm-cmd.c (gdbscm_parse_command_name): Likewise.
* guile/scm-ports.c (gdbscm_open_memory): Likewise.
* guile/scm-value.c (gdbscm_value_to_string): Likewise.
This patch was taken directly from Pedro's branch.
ax_simple is used to append an agent expression operator to an agent
expression string. Therefore, it takes an enum agent_op as input.
There is an instance where it's called to append a raw byte, unrelated
to the enum. It makes the build fail in C++ mode.
This patch introduces ax_raw_byte for that purpose and uses it.
gdb/ChangeLog:
* ax.h (ax_raw_byte): New declaration.
* ax-general.c (ax_raw_byte): New function.
(ax_simple): Use ax_raw_byte.
* ax-gdb.c (gen_printf): Likewise.
The assignment requires a cast in C++. We only use this macro for
vectors of chars, so adding (char *) diretly will do for now.
gdb/ChangeLog:
* ada-lang.h (GROW_VECT): Add cast.
Running ./gdb.ada/access_to_packed_array.exp ...
ERROR: tcl error sourcing ./gdb.ada/access_to_packed_array.exp.
ERROR: extra characters after close-quote
while executing
"gdb_test "print pack.a" "\\(0 => 1, 2, 3, 4, 5, 6, 7, 8, 9, 10\\)")"
(file "./gdb.ada/access_to_packed_array.exp" line 29)
invoked from within
"source ./gdb.ada/access_to_packed_array.exp"
("uplevel" body line 1)
invoked from within
"uplevel #0 source ./gdb.ada/access_to_packed_array.exp"
invoked from within
"catch "uplevel #0 source $test_file_name""
Unrelated to the typos I have changed the print expectations s/"x"/" = x"/
as for example expectation "3" should not match " = 43".
2015-10-27 Jan Kratochvil <jan.kratochvil@redhat.com>
* gdb.ada/access_to_packed_array.exp: Fix typos erroring the testfile.
Fixes some errors in C++ build.
gdb/ChangeLog:
* target.c (memory_xfer_partial): Change type of buf to gdb_byte
pointer.
(simple_search_memory): Cast return of memmem.
gdb/ChangeLog:
PR python/18938
* cli/cli-cmds (source_script_fron_sctream): New arg file_to_open.
All callers updated.
gdb/testsuite/ChangeLog:
* gdb.python/python.exp: Add test for symlink from .py file to .notpy
file.
gdb/ChangeLog:
* nat/linux-nat.h (__SIGRTMIN): Move here from gdbserver/linux-low.c.
gdb/gdbserver/ChangeLog:
* linux-low.c (__SIGRTMIN): Move to nat/linux-nat.h.
gdb/ChangeLog:
* common/gdb_wait.h (W_STOPCODE): Define, moved here from
gdbserver/linux-low.c.
(WSETSTOP): Simplify.
gdb/gdbserver/ChangeLog:
* linux-low.c (W_STOPCODE): Moved to common/gdb_wait.h.
gdb/ChangeLog:
* linux-thread-db.c (find_new_threads_callback): Cast ti.ti_tid to
unsigned long for debug_printf.
(thread_db_pid_to_str): Ditto.
gdb/gdbserver/ChangeLog:
* thread-db.c (find_one_thread): Cast ti.ti_tid to unsigned long
for debug_printf.
(attach_thread, find_new_threads_callback): Ditto.
As pointed out by Pedro, it's clearer to do it this way. We can trust
that scm_mode_bits won't try to modify our string, even though it takes
a non-const char *.
gdb/ChangeLog:
* guile/scm-ports.c (ioscm_make_gdb_stdio_port): Do not pass a
local char array to scm_mode_bits, use a cast instead.
I stumbled upon this while doing some cxx-conversion work. Since the
x-family alloc functions throw on failure, it is useless to test their
result for failure. The else branch of != NULL is basically dead code.
I changed the type of element_block_ptr to struct tui_win_element, which
seems obvious (this is actually what raised the flag, casting the result
of xmalloc to struct tui_win_element* wouldn't work).
gdb/ChangeLog:
* tui/tui-data.c (tui_alloc_content): Don't check xmalloc
result. Change type of element_block_ptr. Change allocation to
use XNEWVEC.
I caught a segmentation fault while running gdb.reverse/sigall-reverse.exp,
in a mingw32 GDB, in this code path. It boils down to the code trying to
strlen () a NULL pointer. I tracked things down and it looks like
record_full_message_wrapper_safe is the only offender.
gdb/ChangeLog:
2015-10-26 Luis Machado <lgustavo@codesourcery.com>
* record-full.c (record_full_message_wrapper_safe): Pass empty string to
catch_errors call instead of NULL.
ioscm_make_gdb_stdio_port passes const char pointers (literal strings) to
scm_mode_bits, which takes a non-const char pointer. Ideally, we would
change scm_mode_bits to take a const char pointer, but it's not part of
an API we control.
Instead, it's easy enough to build the string to pass to scm_mode_bits in
a (non-const) char array and pass that.
gdb/ChangeLog:
* guile/scm-ports.c (ioscm_make_gdb_stdio_port): Pass non-const
char pointer to scm_mode_bits.
By having a local variable of type (const gdb_byte *), we can avoid adding
two casts.
gdb/ChangeLog:
* guile/scm-ports.c (gdbscm_memory_port_write): Declare new
"data" local variable and use it.
We currently pass integers as domain_enums to lookup_symbol. The
most obvious fix is to add casts there.
I first thought of changing the type of the domain variables to
domain_enum. However, because we pass a pointer to them to
gdbscm_parse_function_args, which expects them to be integers (because
of the format string), I don't think it would be correct. If the enum
does not have the same size as an int, gdbscm_parse_function_args could
write past the memory of domain, overwriting something else on the
stack.
gdb/ChangeLog:
* guile/scm-symbol.c (gdbscm_lookup_global_symbol): Add
domain_enum cast.
(gdbscm_lookup_symbol): Likewise.
The (void *) casts make the build fail in C++ mode and are unnecessary.
gdb/ChangeLog:
* tui/tui-data.c (tui_add_to_source_windows): Remove void *
cast.
(tui_add_content_elements): Likewise.
A cast here is necessary, just as it's necessary in ps_pdwrite just
below. The type of buf can't be changed, since it's fixed in the ps_pd*
API.
gdb/ChangeLog:
* proc-service.c (ps_pdread): Add cast.
This:
valbuf = memcpy (buf, valbuf, len);
causes a build failure in C++, because memcpy returns the value of
"buf" as a void *. Instead of adding a cast, we can just do the
assignment separately.
gdb/ChangeLog:
* sparc64-tdep.c (sparc64_store_arguments): Split assignment of
valbuf.
Remove these (void *) casts, which cause a build failure in C++ mode.
gdb/ChangeLog:
* ia64-tdep.c (ia64_pseudo_register_write): Remove cast.
(ia64_push_dummy_call): Remove cast and change type of "to" to
array of gdb_byte.
This patch fixes the build that was broken by :
https://sourceware.org/ml/gdb-patches/2015-10/msg00369.html
It implements the sw_breakpoint_from_kind operation on these targets and removes
the calls to set_breakpoint_data.
Compiliation tested on win32.
Not tested : nto, spu.
gdb/gdbserver/ChangeLog:
* nto-low.c (nto_sw_breakpoint_from_kind): New function.
(struct target_ops) <sw_breakpoint_from_kind>: Initialize.
(initialize_low): Remove set_breakpoint_data call.
* spu-low.c (spu_sw_breakpoint_from_kind): New function.
(struct target_ops) <sw_breakpoint_from_kind>: Iniitalize.
(initialize_low): Remove set_breakpoint_data call.
* win32-low.c (win32_sw_breakpoint_from_kind): New function.
(struct target_ops) <sw_breakpoint_from_kind>: Initialize.
(initialize_low): Remove set_breakpoint_data call.
This patch moves default_breakpoint_kind_from_pc to target.c and creates a macro
so that all targets can easily use it.
This allows the breakpoint_kind_from_pc operation to be left unimplemented in
targets that do not need it.
This is preparation to fix the win32/nto/spu build that was broken by this
patch: https://sourceware.org/ml/gdb-patches/2015-10/msg00369.html
No regression on Ubuntu 14.04 x86-64 with gdbserver-{native-extended}
gdb/gdbserver/ChangeLog:
* linux-low.c (default_breakpoint_kind_from_pc): Move to target.c.
* mem-break.c (set_breakpoint_at): Use target_breakpoint_kind_from_pc.
* target.c (default_breakpoint_kind_from_pc): Moved from linux-low.c
* target.h (target_breakpoint_kind_from_pc): New macro.
This patch initialize dsd.insn_count, otherwise, it triggers the assert
below on testings we did recently.
gdb:
2015-10-23 Yao Qi <yao.qi@linaro.org>
* aarch64-tdep.c (aarch64_displaced_step_copy_insn): Set
dsd.insn_count to zero.
Yao Qi
Simon Marchi
Markus Metzger
Pedro Alves
Kevin Buettner
Joel Brobecker
Tristan Gingold
Tristan Gingold
Doug Evans
Don Breazeal
Jose E. Marchesi
Sandra Loosemore
Dominik Vogt
Marcin Kościelnicki
Andrew Burgess
Jan Kratochvil
Walfred Tedeschi
Simon Marchi
Henrik Wallin
Eli Zaretskii
Simon Dardis
Doug Evans
Luis Machado
Iain Buclaw
Antoine Tremblay