We need to cast the pointer up to 64bits so that the push works on x32
targets. For 64bit targets, this makes no difference.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2013-01-08 Yufeng Zhang <yufeng.zhang@arm.com>
* config/tc-aarch64.c (parse_operands): Change to compare the result
of function call 'parse_sys_reg' with 'PARSE_FAIL' instead of 'FALSE'.
gas/testsuite/
2013-01-08 Yufeng Zhang <yufeng.zhang@arm.com>
* gas/aarch64/diagnostic.s: Add test.
* gas/aarch64/diagnostic.l: Update.
* printcmd.c: Remove define of function output_command.
* tracepoint.c: Remove extern of function output_command.
* valprint.h: (output_command): New extern.
PR gold/14993
* output.cc (Output_section::add_input_section): For incremental
updates, don't track input sections that are allocated from patch
space.
PR gold/14897
* configure.ac (--enable-ld): Removed.
(install_as_default): Set to yes only for --enable-gold=default
or --disable-ld.
* configure: Regenerated.
* objcopy.c (deterministic): Make int rather than bfd_boolean,
initialize to -1.
(strip_options, copy_options): Add -U/--disable-deterministic-archives.
(default_deterministic): New function.
(strip_main, copy_main): Handle -U. Call default_deterministic.
(copy_usage, strip_usage): Describe -U. Cite whether -D or -U is
the default based on DEFAULT_AR_DETERMINISTIC.
* doc/binutils.texi (objcopy, strip): Describe -U and effect of
configure options on -D.
* ar.c (default_deterministic): Comment fix.
* config/tc-arm.c (skip_past_char): Skip whitespace before the
anticipated character.
* config/tc-arm.c (parse_address_main): Delete skip of whitespace
here as it is no longer needed.
PR gas/14887
* gas/arm/neon-ldst-es.s: Add more whitespace.
Correct ordering of M68HC11 entry.
* doc/binutils.texi: Fix ordering of top level nodes.
Replace erroneous uses of @itemx with @item.
* bfd.texinfo: Replace @ with @@ when it is part of the text.
... following Pedro's advice of using a temporary macro.
gdb/gdbserver/ChangeLog:
* lynx-low.c (ptrace_request_to_str): Define a temporary
macro and use it to simplify this function's implementation.
This is not strictly needed, since both GDB and GDBserver seem
to agree on the register numbering without this. But this allows
us to make sure that this is always going to be the case.
gdb/gdbserver/ChangeLog:
* configure.srv (i[34567]86-*-lynxos*): Set srv_xmlfiles.
... back to GDB. The transfer occurs when GDB sends the
'qXfer:features:read:target.xml' packet. This allows us to make
sure that GDB and GDBserver use the same register numbering.
This is important on Lynx 178, where GDB selects the rs6000:6000
architecture by default instead of the powerpc:common architecture.
gdb/gdbserver/ChangeLog:
* configure.srv (powerpc-*-lynxos*): Set srv_xmlfiles.
Before this patch, the ptid passed to lynx_resume was completely
ignored, and we used the current_inferior. This resulted in trying
to resume the inferior execution using the wrong ptid after having
received a thread create/exit event, because the inferior_ptid
was still set to the ptid prior to receiving the signal.
gdb/gdbserver/ChangeLog:
* lynx-low.c (lynx_resume): Use the resume_info parameter
to determine the ptid for the lynx_ptrace call, unless
it is equal to minus_one_ptid, in which case we use the
ptid of the current_inferior.
(lynx_wait_1): After having received a thread create/exit
event, resume the inferior's execution using the signaling
thread's ptid, rather than the old ptid.
* bfd-in2.h: Add support for MIPS r5900
* config.bfd: Add support for Sony Playstation 2
* cpu-mips.c: Add support for MIPS r5900
* elfxx-mips.c: Add support for MIPS r5900 (extension of r4000)
* config/tc-mips.c: Add support for MIPS r5900
Add M_LQ_AB and M_SQ_AB to support large values for instructions lq and sq.
* config/tc-mips.c (can_swap_branch_p, get_append_method): Detect some conditional short loops to fix a bug on the r5900 by NOP in the branch delay slot.
* config/tc-mips.c (M_MUL): Support 3 operands in multu on r5900.
* config/tc-mips.c (M_TRUNCWS): Support trunc.w.s on r5900 in MIPS ISA I.
* config/tc-mips.c (s_mipsset): Force 32 bit floating point on r5900.
* configure.in: Detect CPU type when target string contains r5900 (e.g. mips64r5900el-linux-gnu).
* config/tc-mips.c (mips_ip): Check parameter range of instructions mfps and mtps on r5900.
* elf/mips.h: Add MIPS machine variant number for r5900 which is compatible with old Playstation 2 software.
* opcode/mips.h: Add support for r5900 instructions including lq and sq.
* configure.tgt: Support ELF files for Sony Playstation 2 (for ps2dev and ps2sdk).
* emulparams/elf32lr5900n32.sh: Create linker script for Sony Playstation 2 ELF files using MIPS ABI n32.
* emulparams/elf32lr5900.sh: Create linker script for Sony Playstation 2 ELF files using MIPS ABI o32.
* Makefile.am: Add linker scripts for Sony Playstation 2 ELF files.
* opcodes/mips-dis.c: Add names for CP0 registers of r5900.
* opcodes/mips-opc.c: Add M_SQ_AB and M_LQ_AB to support larger range for instructions sq and lq.
* opcodes/mips-opc.c: Add support for MIPS r5900 CPU.
Add support for 128 bit MMI (Multimedia Instructions).
Add support for EE instructions (Emotion Engine).
Disable unsupported floating point instructions (64 bit and undefined compare operations).
Enable instructions of MIPS ISA IV which are supported by r5900.
Disable 64 bit co processor instructions.
Disable 64 bit multiplication and division instructions.
Disable instructions for co-processor 2 and 3, because these are not supported (preparation for later VU0 support (Vector Unit)).
Disable cvt.w.s because this behaves like trunc.w.s and the correct execution can't be ensured on r5900.
Add trunc.w.s using the opcode encoding of cvt.w.s on r5900. This will confuse less developers and compilers.
