[ Upstream commit 61d2ca503d ]
This was mistakenly copied from the downstream dts, however the upstream
driver works differently.
I only tested this with the pm8150_gpios node (used with volume button),
but the 2 others should be the same.
Fixes: e92b61c8e7 ("arm64: dts: qcom: pm8150l: Add base dts file")
Fixes: 229d5bcad0 ("arm64: dts: qcom: pm8150b: Add base dts file")
Fixes: 5101f22a5c ("arm64: dts: qcom: pm8150: Add base dts file")
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Link: https://lore.kernel.org/r/20200420153543.14512-1-jonathan@marek.ca
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe2aff0c57 ]
The thermal trip points have unit name but no reg property, so we can
remove them. It also fixes the following warnings from 'make dtbs_check'
after adding the thermal yaml bindings.
arch/arm64/boot/dts/qcom/apq8016-sbc.dt.yaml: thermal-zones:
gpu-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8016-sbc.dt.yaml: thermal-zones:
camera-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8016-sbc.dt.yaml: thermal-zones:
modem-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8916-mtp.dt.yaml: thermal-zones:
gpu-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8916-mtp.dt.yaml: thermal-zones:
camera-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8916-mtp.dt.yaml: thermal-zones:
modem-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Link: https://lore.kernel.org/r/2d3d045c18a2fb85b28cf304aa11ae6e6538d75e.1585562459.git.amit.kucheria@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 72b29215ac ]
Fixing several unit name warnings:
Warning (unit_address_vs_reg): /oscillator@0: node has a unit name, but no reg property
Warning (unit_address_vs_reg): /oscillator@1: node has a unit name, but no reg property
Warning (unit_address_vs_reg): /oscillator@2: node has a unit name, but no reg property
Warning (unit_address_vs_reg): /thermal-zones/cpu_thermal/trips/trip-point@0: node has a unit name, but no reg property
Warning (unit_address_vs_reg): /thermal-zones/cpu_thermal/trips/trip-point@1: node has a unit name, but no reg property
Warning (unit_address_vs_reg): /thermal-zones/cpu_thermal/trips/cpu_crit@0: node has a unit name, but no reg property
Warning (unit_address_vs_reg): /thermal-zones/cpu_thermal/cooling-maps/map@0: node has a unit name, but no reg property
Warning (unit_address_vs_reg): /thermal-zones/cpu_thermal/cooling-maps/map@1: node has a unit name, but no reg property
Warning (unit_address_vs_reg): /reserved-memory/vpu_dma_mem_region: node has a reg or ranges property, but no unit name
Warning (simple_bus_reg): /soc/pinctrl@10005000: simple-bus unit address format error, expected "1000b000"
Warning (simple_bus_reg): /soc/interrupt-controller@10220000: simple-bus unit address format error, expected "10221000"
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Link: https://lore.kernel.org/r/20200210063523.133333-4-hsinyi@chromium.org
[mb: drop fixes for '_' in property name]
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb5cce12ac ]
The Arm Ltd. boards were using an outdated address convention in the DT
node names, by separating the high from the low 32-bits of an address by
a comma.
Remove the comma from the node name suffix to be DT spec compliant.
Link: https://lore.kernel.org/r/20200513103016.130417-3-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 78631aecc5 ]
The GIC DT nodes for the fastmodels were not fully compliant with the
DT binding, which has certain expectations about child nodes and their
size and address cells values.
Use smaller #address-cells and #size-cells values, as the binding
requests, and adjust the reg properties accordingly.
This requires adjusting the interrupt nexus nodes as well, as one
field of the interrupt-map property depends on the GIC's address-size.
Since the .dts files share interrupt nexus nodes across different
interrupt controllers (GICv2 vs. GICv3), we need to use the only
commonly allowed #address-size value of <1> for both.
Link: https://lore.kernel.org/r/20200513103016.130417-11-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a78aee9e43 ]
The GIC DT nodes for the Juno boards were not fully compliant with
the DT binding, which has certain expectations about child nodes and
their size and address cells values.
Use smaller #address-cells and #size-cells values, as the binding
requests, and adjust the reg properties accordingly.
This requires adjusting the interrupt nexus nodes as well, as one
field of the interrupt-map property depends on the GIC's address-size.
Link: https://lore.kernel.org/r/20200513103016.130417-10-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c2671acbbb ]
The sfp compatible should be 'sff,sfp', not 'sff,sfp+'. We used patched
kernel where the latter was working.
Fixes: 7109d817db ("arm64: dts: marvell: add DTS for Turris Mox")
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ecded10b4 ]
The GX and AXG SCP sram nodes were using invalid compatible and
node names for the sram entries.
Fixup the sram entries node names, and use proper compatible for them.
It notably fixes:
sram@c8000000: 'scp-shmem@0', 'scp-shmem@200' do not match any of the regexes: '^([a-z]*-)?sram(-section)?@[a-f0-9]+$', 'pinctrl-[0-9]+'
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200326165958.19274-3-narmstrong@baylibre.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 579d1b3faa ]
This patch fixes two issues present in the current function for encoding
arm64 logical immediates when using the 32-bit variants of instructions.
First, the code does not correctly reject an all-ones 32-bit immediate,
and returns an undefined instruction encoding.
Second, the code incorrectly rejects some 32-bit immediates that are
actually encodable as logical immediates. The root cause is that the code
uses a default mask of 64-bit all-ones, even for 32-bit immediates.
This causes an issue later on when the default mask is used to fill the
top bits of the immediate with ones, shown here:
/*
* Pattern: 0..01..10..01..1
*
* Fill the unused top bits with ones, and check if
* the result is a valid immediate (all ones with a
* contiguous ranges of zeroes).
*/
imm |= ~mask;
if (!range_of_ones(~imm))
return AARCH64_BREAK_FAULT;
To see the problem, consider an immediate of the form 0..01..10..01..1,
where the upper 32 bits are zero, such as 0x80000001. The code checks
if ~(imm | ~mask) contains a range of ones: the incorrect mask yields
1..10..01..10..0, which fails the check; the correct mask yields
0..01..10..0, which succeeds.
The fix for both issues is to generate a correct mask based on the
instruction immediate size, and use the mask to check for all-ones,
all-zeroes, and values wider than the mask.
Currently, arch/arm64/kvm/va_layout.c is the only user of this function,
which uses 64-bit immediates and therefore won't trigger these bugs.
We tested the new code against llvm-mc with all 1,302 encodable 32-bit
logical immediates and all 5,334 encodable 64-bit logical immediates.
Fixes: ef3935eeeb ("arm64: insn: Add encoder for bitwise operations using literals")
Suggested-by: Will Deacon <will@kernel.org>
Co-developed-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Luke Nelson <luke.r.nels@gmail.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200508181547.24783-2-luke.r.nels@gmail.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab8ad279ce ]
flush_icache_range() contains a bodge to avoid issuing IPIs when the kgdb
trap handler is running because issuing IPIs is unsafe (and not needed)
in this execution context. However the current test, based on
kgdb_connected is flawed: it both over-matches and under-matches.
The over match occurs because kgdb_connected is set when gdb attaches
to the stub and remains set during normal running. This is relatively
harmelss because in almost all cases irq_disabled() will be false.
The under match is more serious. When kdb is used instead of kgdb to access
the debugger then kgdb_connected is not set in all the places that the
debug core updates sw breakpoints (and hence flushes the icache). This
can lead to deadlock.
Fix by replacing the ad-hoc check with the proper kgdb macro. This also
allows us to drop the #ifdef wrapper.
Fixes: 3b8c9f1cdf ("arm64: IPI each CPU after invalidating the I-cache for kernel mappings")
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200504170518.2959478-1-daniel.thompson@linaro.org
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d2d75ede5 ]
Prior to commit 8eb7e28d4c ("arm64/mm: move runtime pgds to
rodata"), idmap_pgd_dir, tramp_pg_dir, reserved_ttbr0, swapper_pg_dir,
and init_pg_dir were contiguous at the end of the kernel image. The
maintenance at the end of __create_page_tables assumed these were
contiguous, and affected everything from the start of idmap_pg_dir
to the end of init_pg_dir.
That commit moved all but init_pg_dir into the .rodata section, with
other data placed between idmap_pg_dir and init_pg_dir, but did not
update the maintenance. Hence the maintenance is performed on much
more data than necessary (but as the bootloader previously made this
clean to the PoC there is no functional problem).
As we only alter idmap_pg_dir, and init_pg_dir, we only need to perform
maintenance for these. As the other dirs are in .rodata, the bootloader
will have initialised them as expected and cleaned them to the PoC. The
kernel will initialize them as necessary after enabling the MMU.
This patch reworks the maintenance to only cover the idmap_pg_dir and
init_pg_dir to avoid this unnecessary work.
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/20200427235700.112220-1-gshan@redhat.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ef3e40a7ea upstream.
When using the PtrAuth feature in a guest, we need to save the host's
keys before allowing the guest to program them. For that, we dump
them in a per-CPU data structure (the so called host context).
But both call sites that do this are in preemptible context,
which may end up in disaster should the vcpu thread get preempted
before reentering the guest.
Instead, save the keys eagerly on each vcpu_load(). This has an
increased overhead, but is at least safe.
Cc: stable@vger.kernel.org
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0370964dd3 upstream.
On a VHE system, the EL1 state is left in the CPU most of the time,
and only syncronized back to memory when vcpu_put() is called (most
of the time on preemption).
Which means that when injecting an exception, we'd better have a way
to either:
(1) write directly to the EL1 sysregs
(2) synchronize the state back to memory, and do the changes there
For an AArch64, we already do (1), so we are safe. Unfortunately,
doing the same thing for AArch32 would be pretty invasive. Instead,
we can easily implement (2) by calling the put/load architectural
backends, and keep preemption disabled. We can then reload the
state back into EL1.
Cc: stable@vger.kernel.org
Reported-by: James Morse <james.morse@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3204be4109 upstream.
AArch32 CP1x registers are overlayed on their AArch64 counterparts
in the vcpu struct. This leads to an interesting problem as they
are stored in their CPU-local format, and thus a CP1x register
doesn't "hit" the lower 32bit portion of the AArch64 register on
a BE host.
To workaround this unfortunate situation, introduce a bias trick
in the vcpu_cp1x() accessors which picks the correct half of the
64bit register.
Cc: stable@vger.kernel.org
Reported-by: James Morse <james.morse@arm.com>
Tested-by: James Morse <james.morse@arm.com>
Acked-by: James Morse <james.morse@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c582bf4ed upstream.
aarch32 has pairs of registers to access the high and low parts of 64bit
registers. KVM has a union of 64bit sys_regs[] and 32bit copro[]. The
32bit accessors read the high or low part of the 64bit sys_reg[] value
through the union.
Both sys_reg_descs[] and cp15_regs[] list access_csselr() as the accessor
for CSSELR{,_EL1}. access_csselr() is only aware of the 64bit sys_regs[],
and expects r->reg to be 'CSSELR_EL1' in the enum, index 2 of the 64bit
array.
cp15_regs[] uses the 32bit copro[] alias of sys_regs[]. Here CSSELR is
c0_CSSELR which is the same location in sys_reg[]. r->reg is 'c0_CSSELR',
index 4 in the 32bit array.
access_csselr() uses the 32bit r->reg value to access the 64bit array,
so reads and write the wrong value. sys_regs[4], is ACTLR_EL1, which
is subsequently save/restored when we enter the guest.
ACTLR_EL1 is supposed to be read-only for the guest. This register
only affects execution at EL1, and the host's value is restored before
we return to host EL1.
Convert the 32bit register index back to the 64bit version.
Suggested-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200529150656.7339-2-james.morse@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a194c33f45 upstream.
Will reported a UBSAN warning:
UBSAN: null-ptr-deref in arch/arm64/kernel/smp.c:596:6
member access within null pointer of type 'struct acpi_madt_generic_interrupt'
CPU: 0 PID: 0 Comm: swapper Not tainted 5.7.0-rc6-00124-g96bc42ff0a82 #1
Call trace:
dump_backtrace+0x0/0x384
show_stack+0x28/0x38
dump_stack+0xec/0x174
handle_null_ptr_deref+0x134/0x174
__ubsan_handle_type_mismatch_v1+0x84/0xa4
acpi_parse_gic_cpu_interface+0x60/0xe8
acpi_parse_entries_array+0x288/0x498
acpi_table_parse_entries_array+0x178/0x1b4
acpi_table_parse_madt+0xa4/0x110
acpi_parse_and_init_cpus+0x38/0x100
smp_init_cpus+0x74/0x258
setup_arch+0x350/0x3ec
start_kernel+0x98/0x6f4
This is from the use of the ACPI_OFFSET in
arch/arm64/include/asm/acpi.h. Replace its use with offsetof from
include/linux/stddef.h which should implement the same logic using
__builtin_offsetof, so that UBSAN wont warn.
Reported-by: Will Deacon <will@kernel.org>
Suggested-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Jeremy Linton <jeremy.linton@arm.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/lkml/20200521100952.GA5360@willie-the-truck/
Link: https://lore.kernel.org/r/20200608203818.189423-1-ndesaulniers@google.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3b1f6c5e4d ]
Fix the assigned-clock-parents to higher frequency clock to avoid h264
encode timeout:
[ 134.763465] mtk_vpu 10020000.vpu: vpu ipi 4 ack time out !
[ 134.769008] [MTK_VCODEC][ERROR][18]: vpu_enc_send_msg() vpu_ipi_send msg_id c002 len 32 fail -5
[ 134.777707] [MTK_VCODEC][ERROR][18]: vpu_enc_encode() AP_IPIMSG_ENC_ENCODE 0 fail
venc_sel is the clock used by h264 encoder, and venclt_sel is the clock
used by vp8 encoder. Assign venc_sel to vcodecpll_ck and venclt_sel to
vcodecpll_370p5.
vcodecpll 1482000000
vcodecpll_ck 494000000
venc_sel 494000000
...
vcodecpll_370p5 370500000
venclt_sel 370500000
Fixes: fbbad0287c ("arm64: dts: Using standard CCF interface to set vcodec clk")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Link: https://lore.kernel.org/r/20200504124442.208004-1-hsinyi@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c604fd810b ]
Dts files with Rockchip rk3399 'gpu' nodes were manually verified.
In order to automate this process arm,mali-midgard.txt
has been converted to yaml. In the new setup dtbs_check with
arm,mali-midgard.yaml expects interrupts and interrupt-names values
in the same order. Fix this for rk3399.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/gpu/
arm,mali-midgard.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200425143837.18706-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c617ed8850 ]
The status was removed of the '&gmac2phy' node with the apply
of a patch long time ago, so fix status for '&gmac2phy'
in 'rk3328-evb.dts'.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200425122345.12902-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1cf6022bd9 upstream.
Quoth the man page:
```
If the tracee was restarted by PTRACE_SYSCALL or PTRACE_SYSEMU, the
tracee enters syscall-enter-stop just prior to entering any system
call (which will not be executed if the restart was using
PTRACE_SYSEMU, regardless of any change made to registers at this
point or how the tracee is restarted after this stop).
```
The parenthetical comment is currently true on x86 and powerpc,
but not currently true on arm64. arm64 re-checks the _TIF_SYSCALL_EMU
flag after the syscall entry ptrace stop. However, at this point,
it reflects which method was used to re-start the syscall
at the entry stop, rather than the method that was used to reach it.
Fix that by recording the original flag before performing the ptrace
stop, bringing the behavior in line with documentation and x86/powerpc.
Fixes: f086f67485 ("arm64: ptrace: add support for syscall emulation")
Cc: <stable@vger.kernel.org> # 5.3.x-
Signed-off-by: Keno Fischer <keno@juliacomputing.com>
Acked-by: Will Deacon <will@kernel.org>
Tested-by: Sudeep Holla <sudeep.holla@arm.com>
Tested-by: Bin Lu <Bin.Lu@arm.com>
[catalin.marinas@arm.com: moved 'flags' bit masking]
[catalin.marinas@arm.com: changed 'flags' type to unsigned long]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 15ddc3e17a upstream.
Using SDMA1 with UART1 is causing a "Timeout waiting for CH0" error.
This patch changes to ahb clock from SDMA1_ROOT to AHB which fixes the
timeout error.
Fixes: 6c3debcbae ("arm64: dts: freescale: Add i.MX8MN dtsi support")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 190c7f6fd4 upstream.
The device tree compiler complains that the dwc3 nodes have regs
properties but no matching unit addresses.
Add the unit addresses to the device node name. While at it, also rename
the nodes from "dwc3" to "usb", as guidelines require device nodes have
generic names.
Fixes: 7144224f2c ("arm64: dts: rockchip: support dwc3 USB for rk3399")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20200327030414.5903-7-wens@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 83b994129f upstream.
In some board device tree files, "rk805" was used for the RK805 PMIC's
node name. However the policy for device trees is that generic names
should be used.
Replace the "rk805" node name with the generic "pmic" name.
Fixes: 1e28037ec8 ("arm64: dts: rockchip: add rk805 node for rk3328-evb")
Fixes: 955bebde05 ("arm64: dts: rockchip: add rk3328-rock64 board")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20200327030414.5903-3-wens@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5ac0869fb3 upstream.
In the process of moving the VIM3 audio nodes to a G12B specific dtsi
for enabling the SM1 based VIM3L, the frddr_a status = "okay" property
got dropped.
This re-enables the frddr_a node to fix audio support.
Fixes: 4f26cc1c96 ("arm64: dts: khadas-vim3: move common nodes into meson-khadas-vim3.dtsi")
Reported-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20191018140216.4257-1-narmstrong@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d51c214541 ]
The second argument is the end "pointer", not the length.
Fixes: d28f6df130 ("arm64/kexec: Add core kexec support")
Cc: <stable@vger.kernel.org> # 4.8.x-
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 027d0c7101 upstream.
The static analyzer in GCC 10 spotted that in huge_pte_alloc() we may
pass a NULL pmdp into pte_alloc_map() when pmd_alloc() returns NULL:
| CC arch/arm64/mm/pageattr.o
| CC arch/arm64/mm/hugetlbpage.o
| from arch/arm64/mm/hugetlbpage.c:10:
| arch/arm64/mm/hugetlbpage.c: In function ‘huge_pte_alloc’:
| ./arch/arm64/include/asm/pgtable-types.h:28:24: warning: dereference of NULL ‘pmdp’ [CWE-690] [-Wanalyzer-null-dereference]
| ./arch/arm64/include/asm/pgtable.h:436:26: note: in expansion of macro ‘pmd_val’
| arch/arm64/mm/hugetlbpage.c:242:10: note: in expansion of macro ‘pte_alloc_map’
| |arch/arm64/mm/hugetlbpage.c:232:10:
| |./arch/arm64/include/asm/pgtable-types.h:28:24:
| ./arch/arm64/include/asm/pgtable.h:436:26: note: in expansion of macro ‘pmd_val’
| arch/arm64/mm/hugetlbpage.c:242:10: note: in expansion of macro ‘pte_alloc_map’
This can only occur when the kernel cannot allocate a page, and so is
unlikely to happen in practice before other systems start failing.
We can avoid this by bailing out if pmd_alloc() fails, as we do earlier
in the function if pud_alloc() fails.
Fixes: 66b3923a1a ("arm64: hugetlb: add support for PTE contiguous bit")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reported-by: Kyrill Tkachov <kyrylo.tkachov@arm.com>
Cc: <stable@vger.kernel.org> # 4.5.x-
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0225fd5e0a upstream.
In the unlikely event that a 32bit vcpu traps into the hypervisor
on an instruction that is located right at the end of the 32bit
range, the emulation of that instruction is going to increment
PC past the 32bit range. This isn't great, as userspace can then
observe this value and get a bit confused.
Conversly, userspace can do things like (in the context of a 64bit
guest that is capable of 32bit EL0) setting PSTATE to AArch64-EL0,
set PC to a 64bit value, change PSTATE to AArch32-USR, and observe
that PC hasn't been truncated. More confusion.
Fix both by:
- truncating PC increments for 32bit guests
- sanitizing all 32bit regs every time a core reg is changed by
userspace, and that PSTATE indicates a 32bit mode.
Cc: stable@vger.kernel.org
Acked-by: Will Deacon <will@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a9a8ba90fa upstream.
Rather than chunking via PAGE_SIZE, this commit changes the arch
implementations to chunk in explicit 4k parts, so that calculations on
maximum acceptable latency don't suddenly become invalid on platforms
where PAGE_SIZE isn't 4k, such as arm64.
Fixes: 0f961f9f67 ("crypto: x86/nhpoly1305 - add AVX2 accelerated NHPoly1305")
Fixes: 012c82388c ("crypto: x86/nhpoly1305 - add SSE2 accelerated NHPoly1305")
Fixes: a00fa0c887 ("crypto: arm64/nhpoly1305 - add NEON-accelerated NHPoly1305")
Fixes: 16aae3595a ("crypto: arm/nhpoly1305 - add NEON-accelerated NHPoly1305")
Cc: stable@vger.kernel.org
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1578e5d031 upstream.
On arm64 linux gcc uses -fasynchronous-unwind-tables -funwind-tables
by default since gcc-8, so now the de facto platform ABI is to allow
unwinding from async signal handlers.
However on bare metal targets (aarch64-none-elf), and on old gcc,
async and sync unwind tables are not enabled by default to avoid
runtime memory costs.
This means if linux is built with a baremetal toolchain the vdso.so
may not have unwind tables which breaks the gcc platform ABI guarantee
in userspace.
Add -fasynchronous-unwind-tables explicitly to the vgettimeofday.o
cflags to address the ABI change.
Fixes: 28b1a824a4 ("arm64: vdso: Substitute gettimeofday() with C implementation")
Cc: Will Deacon <will@kernel.org>
Reported-by: Szabolcs Nagy <szabolcs.nagy@arm.com>
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c9a4ef6645 ]
In assembly, many instances of __emit_inst(x) expand to a directive. In
a few places __emit_inst(x) is used as an assembler macro argument. For
example, in arch/arm64/kvm/hyp/entry.S
ALTERNATIVE(nop, SET_PSTATE_PAN(1), ARM64_HAS_PAN, CONFIG_ARM64_PAN)
expands to the following by the C preprocessor:
alternative_insn nop, .inst (0xd500401f | ((0) << 16 | (4) << 5) | ((!!1) << 8)), 4, 1
Both comma and space are separators, with an exception that content
inside a pair of parentheses/quotes is not split, so the clang
integrated assembler splits the arguments to:
nop, .inst, (0xd500401f | ((0) << 16 | (4) << 5) | ((!!1) << 8)), 4, 1
GNU as preprocesses the input with do_scrub_chars(). Its arm64 backend
(along with many other non-x86 backends) sees:
alternative_insn nop,.inst(0xd500401f|((0)<<16|(4)<<5)|((!!1)<<8)),4,1
# .inst(...) is parsed as one argument
while its x86 backend sees:
alternative_insn nop,.inst (0xd500401f|((0)<<16|(4)<<5)|((!!1)<<8)),4,1
# The extra space before '(' makes the whole .inst (...) parsed as two arguments
The non-x86 backend's behavior is considered unintentional
(https://sourceware.org/bugzilla/show_bug.cgi?id=25750).
So drop the space separator inside `.inst (...)` to make the clang
integrated assembler work.
Suggested-by: Ilie Halip <ilie.halip@gmail.com>
Signed-off-by: Fangrui Song <maskray@google.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Link: https://github.com/ClangBuiltLinux/linux/issues/939
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 556d687a4c upstream.
In order to use compat_* type defininitions in device drivers
outside of CONFIG_COMPAT, move the inclusion of asm-generic/compat.h
ahead of the #ifdef.
All other architectures already do this.
Acked-by: Will Deacon <will@kernel.org>
Reviewed-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit: 27a22fbdee ]
Clang reports a warning on the __tlbi(aside1is, 0) macro expansion since
the value size does not match the register size specified in the inline
asm. Construct the ASID value using the __TLBI_VADDR() macro.
Fixes: 222fc0c850 ("arm64: compat: Workaround Neoverse-N1 #1542419 for compat user-space")
Reported-by: Nathan Chancellor <natechancellor@gmail.com>
Cc: James Morse <james.morse@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 222fc0c850 ]
Compat user-space is unable to perform ICIMVAU instructions from
user-space. Instead it uses a compat-syscall. Add the workaround for
Neoverse-N1 #1542419 to this code path.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee9d90be9d ]
Systems affected by Neoverse-N1 #1542419 support DIC so do not need to
perform icache maintenance once new instructions are cleaned to the PoU.
For the errata workaround, the kernel hides DIC from user-space, so that
the unnecessary cache maintenance can be trapped by firmware.
To reduce the number of traps, produce a fake IminLine value based on
PAGE_SIZE.
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05460849c3 ]
Cores affected by Neoverse-N1 #1542419 could execute a stale instruction
when a branch is updated to point to freshly generated instructions.
To workaround this issue we need user-space to issue unnecessary
icache maintenance that we can trap. Start by hiding CTR_EL0.DIC.
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 46f94c7818 ]
If the mv88e6xxx DSA driver is built as a module, it causes the
ethernet driver to re-probe when it's loaded. This in turn causes
the gigabit PHY to be momentarily reset and reprogrammed. However,
we attempt to reprogram the PHY immediately after deasserting reset,
and the PHY ignores the writes.
This results in the PHY operating in the wrong mode, and the copper
link states down.
Set a reset deassert delay of 10ms for the gigabit PHY to avoid this.
Fixes: babc5544c2 ("arm64: dts: clearfog-gt-8k: 1G eth PHY reset signal")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f9f711efd4 ]
If the kernel configuration option CONFIG_PCIE_DW_PLAT_HOST is enabled
then this can cause the kernel to incorrectly probe the generic
designware PCIe platform driver instead of the Tegra194 designware PCIe
driver. This causes a boot failure on Tegra194 because the necessary
configuration to access the hardware is not performed.
The order in which the compatible strings are populated in Device-Tree
is not relevant in this case, because the kernel will attempt to probe
the device as soon as a driver is loaded and if the generic designware
PCIe driver is loaded first, then this driver will be probed first.
Therefore, to fix this problem, remove the "snps,dw-pcie" string from
the compatible string as we never want this driver to be probe on
Tegra194.
Fixes: 2602c32f15 ("arm64: tegra: Add P2U and PCIe controller nodes to Tegra194 DT")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3e9a1a8b7f ]
Register range of display clocks is 0x10000, as it can be seen from
DE2 documentation.
Fix it.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Fixes: 2c796fc8f5 ("arm64: dts: allwinner: a64: add necessary device tree nodes for DE2 CCU")
[wens@csie.org: added fixes tag]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 9cc3d0c691 upstream.
The aarch32_vdso_pages[] array never has entries allocated in the C_VVAR
or C_VDSO slots, and as the array is zero initialized these contain
NULL.
However in __aarch32_alloc_vdso_pages() when
aarch32_alloc_kuser_vdso_page() fails we attempt to free the page whose
struct page is at NULL, which is obviously nonsensical.
This patch removes the erroneous page freeing.
Fixes: 7c1deeeb01 ("arm64: compat: VDSO setup for compat layer")
Cc: <stable@vger.kernel.org> # 5.3.x-
Cc: Vincenzo Frascino <vincenzo.frascino@arm.com>
Acked-by: Will Deacon <will@kernel.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dde061b865 upstream.
Without a VBUS supply the dwc3 driver won't go into otg mode.
Fixes: eb4ea0857c ("arm64: dts: fsl: librem5: Add a device tree for the Librem5 devkit")
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b8fdef311a upstream.
Compilers with branch protection support can be configured to enable it by
default, it is likely that distributions will do this as part of deploying
branch protection system wide. As well as the slight overhead from having
some extra NOPs for unused branch protection features this can cause more
serious problems when the kernel is providing pointer authentication to
userspace but not built for pointer authentication itself. In that case our
switching of keys for userspace can affect the kernel unexpectedly, causing
pointer authentication instructions in the kernel to corrupt addresses.
To ensure that we get consistent and reliable behaviour always explicitly
initialise the branch protection mode, ensuring that the kernel is built
the same way regardless of the compiler defaults.
[This is a reworked version of b8fdef311a ("arm64: Always
force a branch protection mode when the compiler has one") for backport.
Kernels prior to 74afda4016 ("arm64: compile the kernel with ptrauth
return address signing") don't have any Makefile machinery for forcing
on pointer auth but still have issues if the compiler defaults it on so
need this reworked version. -- broonie]
Fixes: 7503197562 (arm64: add basic pointer authentication support)
Reported-by: Szabolcs Nagy <szabolcs.nagy@arm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
[catalin.marinas@arm.com: remove Kconfig option in favour of Makefile check]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fc2266011a upstream.
For thumb instructions, call_undef_hook() in traps.c first reads a u16,
and if the u16 indicates a T32 instruction (u16 >= 0xe800), a second
u16 is read, which then makes up the the lower half-word of a T32
instruction. For T16 instructions, the second u16 is not read,
which makes the resulting u32 opcode always have the upper half set to
0.
However, having the upper half of instr_mask in the undef_hook set to 0
masks out the upper half of all thumb instructions - both T16 and T32.
This results in trapped T32 instructions with the lower half-word equal
to the T16 encoding of setend (b650) being matched, even though the upper
half-word is not 0000 and thus indicates a T32 opcode.
An example of such a T32 instruction is eaa0b650, which should raise a
SIGILL since T32 instructions with an eaa prefix are unallocated as per
Arm ARM, but instead works as a SETEND because the second half-word is set
to b650.
This patch fixes the issue by extending instr_mask to include the
upper u32 half, which will still match T16 instructions where the upper
half is 0, but not T32 instructions.
Fixes: 2d888f48e0 ("arm64: Emulate SETEND for AArch32 tasks")
Cc: <stable@vger.kernel.org> # 4.0.x-
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Fredrik Strupe <fredrik@strupe.net>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a81e5442d7 upstream.
The TI sci-clk driver can scan the DT for all clocks provided by system
firmware and does this by checking the clocks property of all nodes, so
we must add this to the dwc3 nodes so USB clocks are available.
Without this USB does not work with latest system firmware i.e.
[ 1.714662] clk: couldn't get parent clock 0 for /interconnect@100000/dwc3@4020000
Fixes: cc54a99464 ("arm64: dts: ti: k3-am6: add USB suppor")
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Cc: stable@kernel.org
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4ae7a3c3d7 upstream.
The commit c35a516a46 ("arm64: dts: allwinner: H5: Add PMU node")
introduced support for the PMU found on the Allwinner H5. However, the
binding only allows for a single compatible, while the patch was adding
two.
Make sure we follow the binding.
Fixes: c35a516a46 ("arm64: dts: allwinner: H5: Add PMU node")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4c7eeb9af3 upstream.
The commit 7aa9b9eb7d ("arm64: dts: allwinner: H6: Add PMU mode")
introduced support for the PMU found on the Allwinner H6. However, the
binding only allows for a single compatible, while the patch was adding
two.
Make sure we follow the binding.
Fixes: 7aa9b9eb7d ("arm64: dts: allwinner: H6: Add PMU mode")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d79e9d7c1e upstream.
The correct setting for the RGMII ports on LS1046ARDB is to
enable delay on both Rx and Tx so the interface mode used must
be PHY_INTERFACE_MODE_RGMII_ID.
Since commit 1b3047b520 ("net: phy: realtek: add support for
configuring the RX delay on RTL8211F") the Realtek 8211F PHY driver
has control over the RGMII RX delay and it is disabling it for
RGMII_TXID. The LS1046ARDB uses two such PHYs in RGMII_ID mode but
in the device tree the mode was described as "rgmii".
Changing the phy-connection-type to "rgmii-id" to address the issue.
Fixes: 3fa395d2c4 ("arm64: dts: add LS1046A DPAA FMan nodes")
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4022d808c4 upstream.
The correct setting for the RGMII ports on LS1043ARDB is to
enable delay on both Rx and Tx so the interface mode used must
be PHY_INTERFACE_MODE_RGMII_ID.
Since commit 1b3047b520 ("net: phy: realtek: add support for
configuring the RX delay on RTL8211F") the Realtek 8211F PHY driver
has control over the RGMII RX delay and it is disabling it for
RGMII_TXID. The LS1043ARDB uses two such PHYs in RGMII_ID mode but
in the device tree the mode was described as "rgmii_txid".
This issue was not apparent at the time as the PHY driver took the
same action for RGMII_TXID and RGMII_ID back then but it became
visible (RX no longer working) after the above patch.
Changing the phy-connection-type to "rgmii-id" to address the issue.
Fixes: bf02f2ffe5 ("arm64: dts: add LS1043A DPAA FMan support")
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f5459da2b upstream.
Building an arm64 defconfig with clang's integrated assembler, this error
occurs:
<instantiation>:2:2: error: unrecognized instruction mnemonic
_ASM_EXTABLE 9999b, 9f
^
arch/arm64/mm/cache.S:50:1: note: while in macro instantiation
user_alt 9f, "dc cvau, x4", "dc civac, x4", 0
^
While GNU as seems fine with case-sensitive macro instantiations, clang
doesn't, so use the actual macro name (_asm_extable) as in the rest of
the file.
Also checked that the generated assembly matches the GCC output.
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Fixes: 290622efc7 ("arm64: fix "dc cvau" cache operation on errata-affected core")
Link: https://github.com/ClangBuiltLinux/linux/issues/924
Signed-off-by: Ilie Halip <ilie.halip@gmail.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b54d390086 ]
The LS1043A SoC is affected by the A050385 erratum stating that
FMAN DMA read or writes under heavy traffic load may cause FMAN
internal resource leak thus stopping further packet processing.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f50b7daccc upstream.
On a system configured to trigger a crash_kexec() reboot, when only one CPU
is online and another CPU panics while starting-up, crash_smp_send_stop()
will fail to send any STOP message to the other already online core,
resulting in fail to freeze and registers not properly saved.
Moreover even if the proper messages are sent (case CPUs > 2)
it will similarly fail to account for the booting CPU when executing
the final stop wait-loop, so potentially resulting in some CPU not
been waited for shutdown before rebooting.
A tangible effect of this behaviour can be observed when, after a panic
with kexec enabled and loaded, on the following reboot triggered by kexec,
the cpu that could not be successfully stopped fails to come back online:
[ 362.291022] ------------[ cut here ]------------
[ 362.291525] kernel BUG at arch/arm64/kernel/cpufeature.c:886!
[ 362.292023] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
[ 362.292400] Modules linked in:
[ 362.292970] CPU: 3 PID: 0 Comm: swapper/3 Kdump: loaded Not tainted 5.6.0-rc4-00003-gc780b890948a #105
[ 362.293136] Hardware name: Foundation-v8A (DT)
[ 362.293382] pstate: 200001c5 (nzCv dAIF -PAN -UAO)
[ 362.294063] pc : has_cpuid_feature+0xf0/0x348
[ 362.294177] lr : verify_local_elf_hwcaps+0x84/0xe8
[ 362.294280] sp : ffff800011b1bf60
[ 362.294362] x29: ffff800011b1bf60 x28: 0000000000000000
[ 362.294534] x27: 0000000000000000 x26: 0000000000000000
[ 362.294631] x25: 0000000000000000 x24: ffff80001189a25c
[ 362.294718] x23: 0000000000000000 x22: 0000000000000000
[ 362.294803] x21: ffff8000114aa018 x20: ffff800011156a00
[ 362.294897] x19: ffff800010c944a0 x18: 0000000000000004
[ 362.294987] x17: 0000000000000000 x16: 0000000000000000
[ 362.295073] x15: 00004e53b831ae3c x14: 00004e53b831ae3c
[ 362.295165] x13: 0000000000000384 x12: 0000000000000000
[ 362.295251] x11: 0000000000000000 x10: 00400032b5503510
[ 362.295334] x9 : 0000000000000000 x8 : ffff800010c7e204
[ 362.295426] x7 : 00000000410fd0f0 x6 : 0000000000000001
[ 362.295508] x5 : 00000000410fd0f0 x4 : 0000000000000000
[ 362.295592] x3 : 0000000000000000 x2 : ffff8000100939d8
[ 362.295683] x1 : 0000000000180420 x0 : 0000000000180480
[ 362.296011] Call trace:
[ 362.296257] has_cpuid_feature+0xf0/0x348
[ 362.296350] verify_local_elf_hwcaps+0x84/0xe8
[ 362.296424] check_local_cpu_capabilities+0x44/0x128
[ 362.296497] secondary_start_kernel+0xf4/0x188
[ 362.296998] Code: 52805001 72a00301 6b01001f 54000ec0 (d4210000)
[ 362.298652] SMP: stopping secondary CPUs
[ 362.300615] Starting crashdump kernel...
[ 362.301168] Bye!
[ 0.000000] Booting Linux on physical CPU 0x0000000003 [0x410fd0f0]
[ 0.000000] Linux version 5.6.0-rc4-00003-gc780b890948a (crimar01@e120937-lin) (gcc version 8.3.0 (GNU Toolchain for the A-profile Architecture 8.3-2019.03 (arm-rel-8.36))) #105 SMP PREEMPT Fri Mar 6 17:00:42 GMT 2020
[ 0.000000] Machine model: Foundation-v8A
[ 0.000000] earlycon: pl11 at MMIO 0x000000001c090000 (options '')
[ 0.000000] printk: bootconsole [pl11] enabled
.....
[ 0.138024] rcu: Hierarchical SRCU implementation.
[ 0.153472] its@2f020000: unable to locate ITS domain
[ 0.154078] its@2f020000: Unable to locate ITS domain
[ 0.157541] EFI services will not be available.
[ 0.175395] smp: Bringing up secondary CPUs ...
[ 0.209182] psci: failed to boot CPU1 (-22)
[ 0.209377] CPU1: failed to boot: -22
[ 0.274598] Detected PIPT I-cache on CPU2
[ 0.278707] GICv3: CPU2: found redistributor 1 region 0:0x000000002f120000
[ 0.285212] CPU2: Booted secondary processor 0x0000000001 [0x410fd0f0]
[ 0.369053] Detected PIPT I-cache on CPU3
[ 0.372947] GICv3: CPU3: found redistributor 2 region 0:0x000000002f140000
[ 0.378664] CPU3: Booted secondary processor 0x0000000002 [0x410fd0f0]
[ 0.401707] smp: Brought up 1 node, 3 CPUs
[ 0.404057] SMP: Total of 3 processors activated.
Make crash_smp_send_stop() account also for the online status of the
calling CPU while evaluating how many CPUs are effectively online: this way
the right number of STOPs is sent and all other stopped-cores's registers
are properly saved.
Fixes: 78fd584cde ("arm64: kdump: implement machine_crash_shutdown()")
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3568b88944 upstream.
The syscall number of compat_clock_getres was erroneously set to 247
(__NR_io_cancel!) instead of 264. This causes the vDSO fallback of
clock_getres() to land on the wrong syscall for compat tasks.
Fix the numbering.
Cc: <stable@vger.kernel.org>
Fixes: 53c489e1df ("arm64: compat: Add missing syscall numbers")
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 26c4b4758f upstream.
There is only on Ethernet port and one Ethernet PHY on imx8qxp-mek.
Remove the unexisting ethphy1 port.
This fixes a run-time warning:
mdio_bus 5b040000.ethernet-1: MDIO device at address 1 is missing.
Fixes: fdea904e85 ("arm64: dts: imx: add imx8qxp mek support")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dd1f6308b2 upstream.
Commit e0d5896bd3 ("arm64: lse: fix LSE atomics with LLVM's integrated
assembler") broke the build when clang is used in connjunction with the
binutils assembler ("-no-integrated-as"). This happens because
__LSE_PREAMBLE is defined as ".arch armv8-a+lse", which overrides the
version of the CPU architecture passed via the "-march" paramter to gas:
$ aarch64-none-linux-gnu-as -EL -I ./arch/arm64/include
-I ./arch/arm64/include/generated
-I ./include -I ./include
-I ./arch/arm64/include/uapi
-I ./arch/arm64/include/generated/uapi
-I ./include/uapi -I ./include/generated/uapi
-I ./init -I ./init
-march=armv8.3-a -o init/do_mounts.o
/tmp/do_mounts-d7992a.s
/tmp/do_mounts-d7992a.s: Assembler messages:
/tmp/do_mounts-d7992a.s:1959: Error: selected processor does not support `autiasp'
/tmp/do_mounts-d7992a.s:2021: Error: selected processor does not support `paciasp'
/tmp/do_mounts-d7992a.s:2157: Error: selected processor does not support `autiasp'
/tmp/do_mounts-d7992a.s:2175: Error: selected processor does not support `paciasp'
/tmp/do_mounts-d7992a.s:2494: Error: selected processor does not support `autiasp'
Fix the issue by replacing ".arch armv8-a+lse" with ".arch_extension lse".
Sami confirms that the clang integrated assembler does now support the
'.arch_extension' directive, so this change will be fine even for LTO
builds in future.
Fixes: e0d5896bd3 ("arm64: lse: fix LSE atomics with LLVM's integrated assembler")
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Reported-by: Amit Kachhap <Amit.Kachhap@arm.com>
Tested-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d0022c0ef2 upstream.
Add brackets around the evaluation of the 'addr' parameter to the
untagged_addr() macro so that the cast to 'u64' applies to the result
of the expression.
Cc: <stable@vger.kernel.org>
Fixes: 597399d0cb ("arm64: tags: Preserve tags for addresses translated via TTBR1")
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3f03a58b25 ]
Add power-domains entry for smmu, so that the it is accessible as long
as the driver is active. Without this device shutdown is throwing the
below warning:
"[ 44.736348] arm-smmu-v3 36600000.smmu: failed to clear cr0"
Reported-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c54f90c262 ]
LLVM's integrated assembler fails with the following error when
building KVM:
<inline asm>:12:6: error: expected absolute expression
.if kvm_update_va_mask == 0
^
<inline asm>:21:6: error: expected absolute expression
.if kvm_update_va_mask == 0
^
<inline asm>:24:2: error: unrecognized instruction mnemonic
NOT_AN_INSTRUCTION
^
LLVM ERROR: Error parsing inline asm
These errors come from ALTERNATIVE_CB and __ALTERNATIVE_CFG,
which test for the existence of the callback parameter in inline
assembly using the following expression:
" .if " __stringify(cb) " == 0\n"
This works with GNU as, but isn't supported by LLVM. This change
splits __ALTERNATIVE_CFG and ALTINSTR_ENTRY into separate macros
to fix the LLVM build.
Link: https://github.com/ClangBuiltLinux/linux/issues/472
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e0d5896bd3 ]
Unlike gcc, clang considers each inline assembly block to be independent
and therefore, when using the integrated assembler for inline assembly,
any preambles that enable features must be repeated in each block.
This change defines __LSE_PREAMBLE and adds it to each inline assembly
block that has LSE instructions, which allows them to be compiled also
with clang's assembler.
Link: https://github.com/ClangBuiltLinux/linux/issues/671
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Tested-by: Andrew Murray <andrew.murray@arm.com>
Tested-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 96ff264bcc ]
An experimental test with the command below gives this error:
rk3399-firefly.dt.yaml: dwmmc@fe310000: wifi@1:
'reg' is a required property
rk3399-orangepi.dt.yaml: dwmmc@fe310000: wifi@1:
'reg' is a required property
rk3399-khadas-edge.dt.yaml: dwmmc@fe310000: wifi@1:
'reg' is a required property
rk3399-khadas-edge-captain.dt.yaml: dwmmc@fe310000: wifi@1:
'reg' is a required property
rk3399-khadas-edge-v.dt.yaml: dwmmc@fe310000: wifi@1:
'reg' is a required property
So fix this by adding a reg property to the brcmf sub node.
Also add #address-cells and #size-cells to prevent more warnings.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200110142128.13522-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7f21473502 ]
An experimental test with the command below gives this error:
px30-evb.dt.yaml: dwmmc@ff390000: clock-names:2:
'ciu-drive' was expected
'ciu-drv' is not a valid dwmmc clock name,
so fix this by changing it to 'ciu-drive'.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200110161200.22755-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e198c395a ]
The WiFi firmware used on db845c implements the 8bit host-capability
message, so enable the quirk for this.
Reviewed-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20191113232245.4039932-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d026c96b25 ]
QUSB2 PHY on msm8996 doesn't work well when autosuspend by
dwc3 core using USB2PHYCFG register is enabled. One of the
issue seen is that PHY driver reports PLL lock failure and
fails phy_init() if dwc3 core has USB2 PHY suspend enabled.
Fix this by using quirks to disable USB2 PHY LPM/suspend and
dwc3 core already takes care of explicitly suspending PHY
during suspend if quirks are specified.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Paolo Pisati <p.pisati@gmail.com>
Link: https://lore.kernel.org/r/20191209151501.26993-1-p.pisati@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c35a516a46 ]
Add the Performance Monitoring Unit (PMU) device tree node to the H5
.dtsi, which tells DT users which interrupts are triggered by PMU
overflow events on each core.
As with the A64, the interrupt numbers from the manual were wrong (off
by 4), the actual SPI IDs have been gathered in U-Boot, and were
verified with perf in Linux.
Tested with perf record and taskset on an OrangePi PC2.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7aa9b9eb7d ]
Add the Performance Monitoring Unit (PMU) device tree node to the H6
.dtsi, which tells DT users which interrupts are triggered by PMU
overflow events on each core. The numbers come from the manual and have
been checked in U-Boot and with perf in Linux.
Tested with perf record and taskset on a Pine H64.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a793e19c15 ]
Although it appeared to follow logically from the bindings, apparently
the thermal framework can't properly cope with a single cooling device
being shared between multiple maps. The CPU zone is probably easier to
overheat, so remove the references to the (optional) fan from the GPU
cooling zone to avoid things getting confused. Hopefully GPU-intensive
tasks will leak enough heat across to the CPU zone to still hit the
fan trips before reaching critical GPU temperatures.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/5bb39f3115df1a487d717d3ae87e523b03749379.1573908197.git.robin.murphy@arm.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3543d7ddd5 upstream.
The interrupt map for the FVP's PCI node is missing the
parent-unit-address cells for each of the INTx entries, leading to the
kernel code failing to parse the entries correctly.
Add the missing zero cells, which are pretty useless as far as the GIC
is concerned, but that the spec requires. This allows INTx to be usable
on the model, and VFIO to work correctly.
Fixes: fa083b99eb ("arm64: dts: fast models: Add DTS fo Base RevC FVP")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fca3d33d8a upstream.
When all CPUs in the system implement the SSBS extension, the SSBS field
in PSTATE is the definitive indication of the mitigation state. Further,
when the CPUs implement the SSBS manipulation instructions (advertised
to userspace via an HWCAP), EL0 can toggle the SSBS field directly and
so we cannot rely on any shadow state such as TIF_SSBD at all.
Avoid forcing the SSBS field in context-switch on such a system, and
simply rely on the PSTATE register instead.
Cc: <stable@vger.kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Srinivas Ramana <sramana@codeaurora.org>
Fixes: cbdf8a189a ("arm64: Force SSBS on context switch")
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 52f73c383b upstream.
We detect the absence of FP/SIMD after an incapable CPU is brought up,
and by then we have kernel threads running already with TIF_FOREIGN_FPSTATE set
which could be set for early userspace applications (e.g, modprobe triggered
from initramfs) and init. This could cause the applications to loop forever in
do_nofity_resume() as we never clear the TIF flag, once we now know that
we don't support FP.
Fix this by making sure that we clear the TIF_FOREIGN_FPSTATE flag
for tasks which may have them set, as we would have done in the normal
case, but avoiding touching the hardware state (since we don't support any).
Also to make sure we handle the cases seemlessly we categorise the
helper functions to two :
1) Helpers for common core code, which calls into take appropriate
actions without knowing the current FPSIMD state of the CPU/task.
e.g fpsimd_restore_current_state(), fpsimd_flush_task_state(),
fpsimd_save_and_flush_cpu_state().
We bail out early for these functions, taking any appropriate actions
(e.g, clearing the TIF flag) where necessary to hide the handling
from core code.
2) Helpers used when the presence of FP/SIMD is apparent.
i.e, save/restore the FP/SIMD register state, modify the CPU/task
FP/SIMD state.
e.g,
fpsimd_save(), task_fpsimd_load() - save/restore task FP/SIMD registers
fpsimd_bind_task_to_cpu() \
- Update the "state" metadata for CPU/task.
fpsimd_bind_state_to_cpu() /
fpsimd_update_current_state() - Update the fp/simd state for the current
task from memory.
These must not be called in the absence of FP/SIMD. Put in a WARNING
to make sure they are not invoked in the absence of FP/SIMD.
KVM also uses the TIF_FOREIGN_FPSTATE flag to manage the FP/SIMD state
on the CPU. However, without FP/SIMD support we trap all accesses and
inject undefined instruction. Thus we should never "load" guest state.
Add a sanity check to make sure this is valid.
Fixes: 82e0191a1a ("arm64: Support systems without FP/ASIMD")
Cc: Will Deacon <will@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c9d66999f0 upstream.
When fp/simd is not supported on the system, fail the operations
of FP/SIMD regsets.
Fixes: 82e0191a1a ("arm64: Support systems without FP/ASIMD")
Cc: Will Deacon <will@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7559950aef upstream.
We set the compat_elf_hwcap bits unconditionally on arm64 to
include the VFP and NEON support. However, the FP/SIMD unit
is optional on Arm v8 and thus could be missing. We already
handle this properly in the kernel, but still advertise to
the COMPAT applications that the VFP is available. Fix this
to make sure we only advertise when we really have them.
Fixes: 82e0191a1a ("arm64: Support systems without FP/ASIMD")
Cc: Will Deacon <will@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 449443c03d upstream.
The NO_FPSIMD capability is defined with scope SYSTEM, which implies
that the "absence" of FP/SIMD on at least one CPU is detected only
after all the SMP CPUs are brought up. However, we use the status
of this capability for every context switch. So, let us change
the scope to LOCAL_CPU to allow the detection of this capability
as and when the first CPU without FP is brought up.
Also, the current type allows hotplugged CPU to be brought up without
FP/SIMD when all the current CPUs have FP/SIMD and we have the userspace
up. Fix both of these issues by changing the capability to
BOOT_RESTRICTED_LOCAL_CPU_FEATURE.
Fixes: 82e0191a1a ("arm64: Support systems without FP/ASIMD")
Cc: Will Deacon <will@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 62bba54d99 upstream.
Explicitly set the switch cpu (upstream) port phy-mode and managed
properties. This fixes the Marvell 88E6141 switch serdes configuration
with the recently enabled phylink layer.
Fixes: a612083327 ("arm64: dts: add support for SolidRun Clearfog GT 8K")
Reported-by: Denis Odintsov <d.odintsov@traviangames.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1eebac0240 upstream.
The uDPU uses both ethernet controllers, which ties up COMPHY 0 for
eth1 and COMPHY 1 for eth0, with no USB3 comphy. The addition of
COMPHY support made the kernel override the setup by the boot loader
breaking this platform by assuming that COMPHY 0 was always used for
USB3. Delete the USB3 COMPHY definition at platform level, and add
phy specifications for the ethernet channels.
Fixes: bd3d25b073 ("arm64: dts: marvell: armada-37xx: link USB hosts with their PHYs")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05caa5bf9c upstream.
The tcsr syscon region is really 0x40000 in size. We need access to the
full region so that we can access the axi resets when managing the
modem subsystem.
Fixes: c783394956 ("arm64: dts: qcom: msm8998: Add smem related nodes")
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Link: https://lore.kernel.org/r/20191107045948.4341-1-jeffrey.l.hugo@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eac8ce86cb upstream.
vdd_apc is the regulator that supplies the main CPU cluster.
At sudden CPU load changes, we have noticed invalid page faults on
addresses with all bits shifted, as well as on addresses with individual
bits flipped.
By putting the vdd_apc regulator in high power mode, the voltage drops
during sudden load changes will be less severe, and we have not been able
to reproduce the invalid page faults with the regulator in this mode.
Fixes: 8faea8edbb ("arm64: dts: qcom: qcs404-evb: add spmi regulators")
Cc: stable@vger.kernel.org
Suggested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20191014120920.12691-1-niklas.cassel@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5441c6507b upstream.
The SIMD based GHASH implementation for arm64 is typically much faster
than the generic one, and doesn't use any lookup tables, so it is
clearly preferred when available. So bump the priority to reflect that.
Fixes: 5a22b198cd ("crypto: arm64/ghash - register PMULL variants ...")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b6ae256afd upstream.
On AArch64 you can do a sign-extended load to either a 32-bit or 64-bit
register, and we should only sign extend the register up to the width of
the register as specified in the operation (by using the 32-bit Wn or
64-bit Xn register specifier).
As it turns out, the architecture provides this decoding information in
the SF ("Sixty-Four" -- how cute...) bit.
Let's take advantage of this with the usual 32-bit/64-bit header file
dance and do the right thing on AArch64 hosts.
Signed-off-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191212195055.5541-1-christoffer.dall@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1cfbb484de upstream.
Confusingly, there are three SPSR layouts that a kernel may need to deal
with:
(1) An AArch64 SPSR_ELx view of an AArch64 pstate
(2) An AArch64 SPSR_ELx view of an AArch32 pstate
(3) An AArch32 SPSR_* view of an AArch32 pstate
When the KVM AArch32 support code deals with SPSR_{EL2,HYP}, it's either
dealing with #2 or #3 consistently. On arm64 the PSR_AA32_* definitions
match the AArch64 SPSR_ELx view, and on arm the PSR_AA32_* definitions
match the AArch32 SPSR_* view.
However, when we inject an exception into an AArch32 guest, we have to
synthesize the AArch32 SPSR_* that the guest will see. Thus, an AArch64
host needs to synthesize layout #3 from layout #2.
This patch adds a new host_spsr_to_spsr32() helper for this, and makes
use of it in the KVM AArch32 support code. For arm64 we need to shuffle
the DIT bit around, and remove the SS bit, while for arm we can use the
value as-is.
I've open-coded the bit manipulation for now to avoid having to rework
the existing PSR_* definitions into PSR64_AA32_* and PSR32_AA32_*
definitions. I hope to perform a more thorough refactoring in future so
that we can handle pstate view manipulation more consistently across the
kernel tree.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Alexandru Elisei <alexandru.elisei@arm.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200108134324.46500-4-mark.rutland@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c2483f154 upstream.
When KVM injects an exception into a guest, it generates the CPSR value
from scratch, configuring CPSR.{M,A,I,T,E}, and setting all other
bits to zero.
This isn't correct, as the architecture specifies that some CPSR bits
are (conditionally) cleared or set upon an exception, and others are
unchanged from the original context.
This patch adds logic to match the architectural behaviour. To make this
simple to follow/audit/extend, documentation references are provided,
and bits are configured in order of their layout in SPSR_EL2. This
layout can be seen in the diagram on ARM DDI 0487E.a page C5-426.
Note that this code is used by both arm and arm64, and is intended to
fuction with the SPSR_EL2 and SPSR_HYP layouts.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Alexandru Elisei <alexandru.elisei@arm.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200108134324.46500-3-mark.rutland@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a425372e73 upstream.
When KVM injects an exception into a guest, it generates the PSTATE
value from scratch, configuring PSTATE.{M[4:0],DAIF}, and setting all
other bits to zero.
This isn't correct, as the architecture specifies that some PSTATE bits
are (conditionally) cleared or set upon an exception, and others are
unchanged from the original context.
This patch adds logic to match the architectural behaviour. To make this
simple to follow/audit/extend, documentation references are provided,
and bits are configured in order of their layout in SPSR_EL2. This
layout can be seen in the diagram on ARM DDI 0487E.a page C5-429.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Alexandru Elisei <alexandru.elisei@arm.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200108134324.46500-2-mark.rutland@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e533dbe9dc upstream.
Since commit:
d44f1b8dd7 ("arm64: KVM/mm: Move SEA handling behind a single 'claim' interface")
... the top-level APEI SEA handler has the shape:
1. current_flags = arch_local_save_flags()
2. local_daif_restore(DAIF_ERRCTX)
3. <GHES handler>
4. local_daif_restore(current_flags)
However, since commit:
4a503217ce ("arm64: irqflags: Use ICC_PMR_EL1 for interrupt masking")
... when pseudo-NMIs (pNMIs) are in use, arch_local_save_flags() will save
the PMR value rather than the DAIF flags.
The combination of these two commits means that the APEI SEA handler will
erroneously attempt to restore the PMR value into DAIF. Fix this by
factoring local_daif_save_flags() out of local_daif_save(), so that we
can consistently save DAIF in step #1, regardless of whether pNMIs are in
use.
Both commits were introduced concurrently in v5.0.
Cc: <stable@vger.kernel.org>
Fixes: 4a503217ce ("arm64: irqflags: Use ICC_PMR_EL1 for interrupt masking")
Fixes: d44f1b8dd7 ("arm64: KVM/mm: Move SEA handling behind a single 'claim' interface")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Julien Thierry <julien.thierry.kdev@gmail.com>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d7bbd6c1b0 upstream.
Since v4.3-rc1 commit 0723c05fb7 ("arm64: enable more compressed
Image formats"), it is possible to build Image.{bz2,lz4,lzma,lzo}
AArch64 images. However, the commit missed adding support for removing
those images on 'make ARCH=arm64 (dist)clean'.
Fix this by adding them to the target list.
Make sure to match the order of the recipes in the makefile.
Cc: stable@vger.kernel.org # v4.3+
Fixes: 0723c05fb7 ("arm64: enable more compressed Image formats")
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4942dc6638 upstream.
On VHE systems arch.mdcr_el2 is written to mdcr_el2 at vcpu_load time to
set options for self-hosted debug and the performance monitors
extension.
Unfortunately the value of arch.mdcr_el2 is not calculated until
kvm_arm_setup_debug() in the run loop after the vcpu has been loaded.
This means that the initial brief iterations of the run loop use a zero
value of mdcr_el2 - until the vcpu is preempted. This also results in a
delay between changes to vcpu->guest_debug taking effect.
Fix this by writing to mdcr_el2 in kvm_arm_setup_debug() on VHE systems
when a change to arch.mdcr_el2 has been detected.
Fixes: d5a21bcc29 ("KVM: arm64: Move common VHE/non-VHE trap config in separate functions")
Cc: <stable@vger.kernel.org> # 4.17.x-
Suggested-by: James Morse <james.morse@arm.com>
Acked-by: Will Deacon <will@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Andrew Murray <andrew.murray@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 54fb3fe0f2 upstream.
This reverts commit 193d00a2b3.
Commit 951d48855d ("of: Make of_dma_get_range() work on bus nodes")
reworked the logic such that of_dma_get_range() works correctly
starting from a bus node containing "dma-ranges".
Since on Juno we don't have a SoC level bus node and "dma-ranges" is
present only in the root node, we get the following error:
OF: translation of DMA address(0) to CPU address failed node(/sram@2e000000)
OF: translation of DMA address(0) to CPU address failed node(/uart@7ff80000)
...
OF: translation of DMA address(0) to CPU address failed node(/mhu@2b1f0000)
OF: translation of DMA address(0) to CPU address failed node(/iommu@2b600000)
OF: translation of DMA address(0) to CPU address failed node(/iommu@2b600000)
OF: translation of DMA address(0) to CPU address failed node(/iommu@2b600000)
So let's fix it by dropping the "dma-ranges" property for now. This
should be fine since it doesn't represent any kind of device-visible
restriction; it was only there for completeness, and we've since given
in to the assumption that missing "dma-ranges" implies a 1:1 mapping
anyway.
We can add it later with a proper SoC bus node and moving all the
devices that belong there along with the "dma-ranges" if required.
Fixes: 193d00a2b3 ("arm64: dts: juno: add dma-ranges property")
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6b832a1487 upstream.
As it was found recently, the Performance Monitoring Unit (PMU) on the
Allwinner A64 SoC was not generating (the right) interrupts. With the
SPI numbers from the manual the kernel did not receive any overflow
interrupts, so perf was not happy at all.
It turns out that the numbers were just off by 4, so the PMU interrupts
are from 148 to 151, not from 152 to 155 as the manual describes.
This was found by playing around with U-Boot, which typically does not
use interrupts, so the GIC is fully available for experimentation:
With *every* PPI and SPI enabled, an overflowing PMU cycle counter was
found to set a bit in one of the GICD_ISPENDR registers, with careful
counting this was determined to be number 148.
Tested with perf record and perf top on a Pine64-LTS. Also tested with
tasksetting to every core to confirm the assignment between IRQs and
cores.
This somewhat "revert-fixes" commit ed3e9406bc ("arm64: dts: allwinner:
a64: Drop PMU node").
Fixes: 34a97fcc71 ("arm64: dts: allwinner: a64: Add PMU node")
Fixes: ed3e9406bc ("arm64: dts: allwinner: a64: Drop PMU node")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 43b0a4b482 upstream.
This is unused on cheza. Delete the node to get ride of the reserved-
memory section, and to avoid the driver from attempting to load a zap
shader that doesn't exist every time it powers up the GPU.
This also avoids a massive amount of dmesg spam about missing zap fw:
msm ae00000.mdss: [drm:adreno_request_fw] *ERROR* failed to load
qcom/a630_zap.mdt: -2
adreno 5000000.gpu: [drm:adreno_zap_shader_load] *ERROR* Unable to
load a630_zap.mdt
Signed-off-by: Rob Clark <robdclark@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Fixes: 3fdeaee951 ("arm64: dts: sdm845: Add zap shader region for GPU")
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e8b395b236 upstream.
Assign clocks and clock-rates for audio plls, that audio
drivers can utilize them.
Add dai-tdm-slot-num and dai-tdm-slot-width for sound-wm8524,
that sai driver can generate correct bit clock.
Fixes: 13f3b9fdef ("arm64: dts: imx8mm-evk: Enable audio codec wm8524")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a381325812 upstream.
This patch removes audio port node from SoC device tree and
fixes the below dtb warning
Warning (unit_address_vs_reg): /soc/sound@ec500000/ports/port@0: node has a unit name, but no reg property
Fixes: e2f04248fc ("arm64: dts: renesas: r8a774a1: Add audio support")
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Link: https://lore.kernel.org/r/1570200761-884-1-git-send-email-biju.das@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e231c6d47c upstream.
CPU clocks have been added to AP806-quad but not to the -dual
variant.
Fixes: c00bc38354 ("arm64: dts: marvell: Add cpu clock node on Armada 7K/8K")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 28a1b34c00 upstream.
The pwm3 was incorrectly added with a compatible reference to the
renesas,pwm-r8a7790 (H2) due to a single characther ommision.
Fix the compatible string.
Fixes: de625477c6 ("arm64: dts: renesas: r8a779{7|8}0: add PWM support")
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Link: https://lore.kernel.org/r/20190912103143.985-1-kieran.bingham+renesas@ideasonboard.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 22c4b148a0 upstream.
The register region size initially is too small to access all
the fifo registers.
Fixes: c59b7fe5aa ("arm64: dts: meson: g12a: add audio fifos")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 301b94d434 upstream.
The register region size initially is too small to access all
the fifo registers.
Fixes: f2b8f6a933 ("arm64: dts: meson-axg: add audio fifos")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a636f93fcd upstream.
Boot failure has been reported on MSM8998 based laptop when
coresight is enabled. This is most likely due to lack of
firmware support for coresight on production device when
compared to debug device like MTP where this issue is not
observed. So disable coresight by default for MSM8998 and
enable it only for MSM8998 MTP.
Reported-and-tested-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Fixes: 783abfa224 ("arm64: dts: qcom: msm8998: Add Coresight support")
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 210de0e996 upstream.
Fix up the correct interrupt numbers for the PMU unit on Agilex
and Stratix10.
Fixes: 78cd6a9d8e ("arm64: dts: Add base stratix 10 dtsi")
Cc: linux-stable <stable@vger.kernel.org>
Reported-by: Meng Li <Meng.Li@windriver.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8467ebbf70 upstream.
A64-OLinuXino-eMMC uses 1.8V for eMMC supply. This is done via a triple
jumper, which sets VCC-PL to either 1.8V or 3.3V. This setting is different
for boards with and without eMMC.
This is not a big issue for DDR52 mode, however the eMMC will not work in
HS200/HS400, since these modes explicitly requires 1.8V.
Fixes: 94f68f3a4b ("arm64: dts: allwinner: a64: Add A64 OlinuXino board (with eMMC)")
Cc: stable@vger.kernel.org # v5.4
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d615c2fc2 upstream.
A64-OLinuXino uses DCDC1 (VCC-IO) for MMC1 supply. In commit 916b68cfe4
("arm64: dts: a64-olinuxino: Enable RTL8723BS WiFi") ALDO2 is set, which is
VCC-PL. Since DCDC1 is always present, the boards are working without a
problem.
This patch sets the correct regulator.
Fixes: 916b68cfe4 ("arm64: dts: a64-olinuxino: Enable RTL8723BS WiFi")
Cc: stable@vger.kernel.org # v4.16+
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 24a572bf67 upstream.
Using SDMA1 with UART1 is causing a "Timeout waiting for CH0" error.
This patch changes to ahb clock from SDMA1_ROOT to AHB which
fixes the timeout error.
Fixes: a05ea40eb3 ("arm64: dts: imx: Add i.mx8mm dtsi support")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e38161bd32 upstream.
In the same way as for msm8974-hammerhead, l21 load, used for SDCARD
VMMC, needs to be increased in order to prevent any voltage drop issues
(due to limited current) happening with some SDCARDS or during specific
operations (e.g. write).
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes: 660a9763c6 (arm64: dts: qcom: db820c: Add pm8994 regulator node)
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9b537997b6 upstream.
A warning is found by the static code analysis tool:
"Identical condition 'err', second condition is always false"
Fix this by adding return value of skcipher_walk_done().
Fixes: 67cfa5d3b7 ("crypto: arm64/aes-neonbs - implement ciphertext stealing for XTS")
Signed-off-by: Yunfeng Ye <yeyunfeng@huawei.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a4376f2fbc upstream.
This is required for clone3 which passes the TLS value through a
struct rather than a register.
Signed-off-by: Amanieu d'Antras <amanieu@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: <stable@vger.kernel.org> # 5.3.x
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20200102172413.654385-3-amanieu@gmail.com
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3e3c8ca5a3 upstream.
Previously this was only defined in the internal headers which
resulted in __NR_clone3 not being defined in the user headers.
Signed-off-by: Amanieu d'Antras <amanieu@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: <stable@vger.kernel.org> # 5.3.x
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20200102172413.654385-2-amanieu@gmail.com
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit aa638cfe3e ]
HiSilicon Taishan v110 CPUs didn't implement CSV2 field of the
ID_AA64PFR0_EL1, but spectre-v2 is mitigated by hardware, so
whitelist the MIDR in the safe list.
Signed-off-by: Wei Li <liwei391@huawei.com>
[hanjun: re-write the commit log]
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f0fb37b22 ]
The reboot register isn't located inside the DCFG controller, but in its
own RST controller. Fix it.
Fixes: 8897f3255c ("arm64: dts: Add support for NXP LS1028A SoC")
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 961f8209c8 ]
The temperature sensor may jump backwards because there is a wrong
calibration value. Both values have to be monotonically increasing.
Fix it.
This was tested on a custom board.
Fixes: 571cebfe8e ("arm64: dts: ls1028a: Add Thermal Monitor Unit node")
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b40dd23f9a upstream.
The retention idle state does not appear to be supported by the firmware
present on the msm8998 laptops since the state is advertised as disabled
in ACPI, and attempting to enable the state in DT is observed to result
in boot hangs. Therefore, remove the state from use to address the
observed issues.
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Fixes: 2c6d2d3a58 (arm64: dts: qcom: Add Lenovo Miix 630)
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 24cecc3774 upstream.
The ARMv8 64-bit architecture supports execute-only user permissions by
clearing the PTE_USER and PTE_UXN bits, practically making it a mostly
privileged mapping but from which user running at EL0 can still execute.
The downside, however, is that the kernel at EL1 inadvertently reading
such mapping would not trip over the PAN (privileged access never)
protection.
Revert the relevant bits from commit cab15ce604 ("arm64: Introduce
execute-only page access permissions") so that PROT_EXEC implies
PROT_READ (and therefore PTE_USER) until the architecture gains proper
support for execute-only user mappings.
Fixes: cab15ce604 ("arm64: Introduce execute-only page access permissions")
Cc: <stable@vger.kernel.org> # 4.9.x-
Acked-by: Will Deacon <will@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit feee6b2989 upstream.
We currently try to shrink a single zone when removing memory. We use
the zone of the first page of the memory we are removing. If that
memmap was never initialized (e.g., memory was never onlined), we will
read garbage and can trigger kernel BUGs (due to a stale pointer):
BUG: unable to handle page fault for address: 000000000000353d
#PF: supervisor write access in kernel mode
#PF: error_code(0x0002) - not-present page
PGD 0 P4D 0
Oops: 0002 [#1] SMP PTI
CPU: 1 PID: 7 Comm: kworker/u8:0 Not tainted 5.3.0-rc5-next-20190820+ #317
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.4
Workqueue: kacpi_hotplug acpi_hotplug_work_fn
RIP: 0010:clear_zone_contiguous+0x5/0x10
Code: 48 89 c6 48 89 c3 e8 2a fe ff ff 48 85 c0 75 cf 5b 5d c3 c6 85 fd 05 00 00 01 5b 5d c3 0f 1f 840
RSP: 0018:ffffad2400043c98 EFLAGS: 00010246
RAX: 0000000000000000 RBX: 0000000200000000 RCX: 0000000000000000
RDX: 0000000000200000 RSI: 0000000000140000 RDI: 0000000000002f40
RBP: 0000000140000000 R08: 0000000000000000 R09: 0000000000000001
R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000140000
R13: 0000000000140000 R14: 0000000000002f40 R15: ffff9e3e7aff3680
FS: 0000000000000000(0000) GS:ffff9e3e7bb00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000000000000353d CR3: 0000000058610000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
__remove_pages+0x4b/0x640
arch_remove_memory+0x63/0x8d
try_remove_memory+0xdb/0x130
__remove_memory+0xa/0x11
acpi_memory_device_remove+0x70/0x100
acpi_bus_trim+0x55/0x90
acpi_device_hotplug+0x227/0x3a0
acpi_hotplug_work_fn+0x1a/0x30
process_one_work+0x221/0x550
worker_thread+0x50/0x3b0
kthread+0x105/0x140
ret_from_fork+0x3a/0x50
Modules linked in:
CR2: 000000000000353d
Instead, shrink the zones when offlining memory or when onlining failed.
Introduce and use remove_pfn_range_from_zone(() for that. We now
properly shrink the zones, even if we have DIMMs whereby
- Some memory blocks fall into no zone (never onlined)
- Some memory blocks fall into multiple zones (offlined+re-onlined)
- Multiple memory blocks that fall into different zones
Drop the zone parameter (with a potential dubious value) from
__remove_pages() and __remove_section().
Link: http://lkml.kernel.org/r/20191006085646.5768-6-david@redhat.com
Fixes: f1dd2cd13c ("mm, memory_hotplug: do not associate hotadded memory to zones until online") [visible after d0dc12e86b]
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Cc: Michal Hocko <mhocko@suse.com>
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.ibm.com>
Cc: Pavel Tatashin <pasha.tatashin@soleen.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Logan Gunthorpe <logang@deltatee.com>
Cc: <stable@vger.kernel.org> [5.0+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1ce74e96c2 upstream.
Commit 4b927b94d5 ("KVM: arm/arm64: vgic: Introduce find_reg_by_id()")
introduced 'find_reg_by_id()', which looks up a system register only if
the 'id' index parameter identifies a valid system register. As part of
the patch, existing callers of 'find_reg()' were ported over to the new
interface, but this breaks 'index_to_sys_reg_desc()' in the case that the
initial lookup in the vCPU target table fails because we will then call
into 'find_reg()' for the system register table with an uninitialised
'param' as the key to the lookup.
GCC 10 is bright enough to spot this (amongst a tonne of false positives,
but hey!):
| arch/arm64/kvm/sys_regs.c: In function ‘index_to_sys_reg_desc.part.0.isra’:
| arch/arm64/kvm/sys_regs.c:983:33: warning: ‘params.Op2’ may be used uninitialized in this function [-Wmaybe-uninitialized]
| 983 | (u32)(x)->CRn, (u32)(x)->CRm, (u32)(x)->Op2);
| [...]
Revert the hunk of 4b927b94d5 which breaks 'index_to_sys_reg_desc()' so
that the old behaviour of checking the index upfront is restored.
Fixes: 4b927b94d5 ("KVM: arm/arm64: vgic: Introduce find_reg_by_id()")
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191212094049.12437-1-will@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bfcef4ab1d ]
In cases like suspend-to-disk and suspend-to-ram, a large number of CPU
cores need to be shut down. At present, the CPU hotplug operation is
serialised, and the CPU cores can only be shut down one by one. In this
process, if PSCI affinity_info() does not return LEVEL_OFF quickly,
cpu_psci_cpu_kill() needs to wait for 10ms. If hundreds of CPU cores
need to be shut down, it will take a long time.
Normally, there is no need to wait 10ms in cpu_psci_cpu_kill(). So
change the wait interval from 10 ms to max 1 ms and use usleep_range()
instead of msleep() for more accurate timer.
In addition, reducing the time interval will increase the messages
output, so remove the "Retry ..." message, instead, track time and
output to the the sucessful message.
Signed-off-by: Yunfeng Ye <yeyunfeng@huawei.com>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit bed903167a upstream.
Commit ef72171b36 ("arm64: dts: exynos: Remove unneeded address space
mapping for soc node") changed the address and size cells in root node from
2 to 1, but /memory nodes for the affected boards were not updated. This
went unnoticed on Exynos5433-based TM2(e) boards, because they use u-boot,
which updates /memory node to the correct values. On the other hand, the
mentioned commit broke boot on Exynos7-based Espresso board, which
bootloader doesn't touch /memory node at all.
This patch reverts commit ef72171b36 ("arm64: dts: exynos: Remove
unneeded address space mapping for soc node"), so Exynos5433 and Exynos7
SoCs again matches other ARM64 platforms with 64bit mappings in root
node.
Reported-by: Alim Akhtar <alim.akhtar@samsung.com>
Fixes: ef72171b36 ("arm64: dts: exynos: Remove unneeded address space mapping for soc node")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: <stable@vger.kernel.org> # 5.3.x: 72ddcf6aa2 arm64: dts: exynos: Move GPU under /soc node for Exynos5433
Cc: <stable@vger.kernel.org> # 5.3.x: ede87c3a2b arm64: dts: exynos: Move GPU under /soc node for Exynos7
Cc: <stable@vger.kernel.org> # 4.18.x
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit df325e05a6 upstream.
__range_ok(), invoked from access_ok(), clears the tag of the user
address only if CONFIG_ARM64_TAGGED_ADDR_ABI is enabled and the thread
opted in to the relaxed ABI. The latter sets the TIF_TAGGED_ADDR thread
flag. In the case of asynchronous I/O (e.g. io_submit()), the
access_ok() may be called from a kernel thread. Since kernel threads
don't have TIF_TAGGED_ADDR set, access_ok() will fail for valid tagged
user addresses. Example from the ffs_user_copy_worker() thread:
use_mm(io_data->mm);
ret = ffs_copy_to_iter(io_data->buf, ret, &io_data->data);
unuse_mm(io_data->mm);
Relax the __range_ok() check to always untag the user address if called
in the context of a kernel thread. The user pointers would have already
been checked via aio_setup_rw() -> import_{single_range,iovec}() at the
time of the asynchronous I/O request.
Fixes: 63f0c60379 ("arm64: Introduce prctl() options to control the tagged user addresses ABI")
Cc: <stable@vger.kernel.org> # 5.4.x-
Cc: Will Deacon <will@kernel.org>
Reported-by: Evgenii Stepanov <eugenis@google.com>
Tested-by: Evgenii Stepanov <eugenis@google.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d440538e5f upstream.
Commit 4fdbfd60a3a2 ("arm64: tegra: Add PCIe slot supply information
in p2972-0000 platform") added regulators for the PCIe slot on the
Jetson Xavier platform. One of these regulators has an active-low enable
and this commit incorrectly added an active-low specifier for the GPIO
which causes the following warning to occur on boot ...
WARNING KERN regulator@3 GPIO handle specifies active low - ignored
The fixed-regulator binding does not use the active-low flag from the
gpio specifier and purely relies of the presence of the
'enable-active-high' property to determine if it is active high or low
(if this property is omitted). Fix this warning by setting the GPIO
to active-high in the GPIO specifier. Finally, remove the
'enable-active-low' as this is not a valid property.
Fixes: 4fdbfd60a3a2 ("arm64: tegra: Add PCIe slot supply information in p2972-0000 platform")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1e5e929c00 upstream.
Commit 3499359418 ("arm64: tegra: Enable HDMI on Jetson TX1")
added a regulator for HDMI on the Jetson TX1 platform. This regulator
has an active high enable, but the GPIO specifier for enabling the
regulator incorrectly defines it as active-low. This causes the
following warning to occur on boot ...
WARNING KERN regulator@10 GPIO handle specifies active low - ignored
The fixed-regulator binding does not use the active-low flag from the
gpio specifier and purely relies of the presence of the
'enable-active-high' property to determine if it is active high or low
(if this property is omitted). Fix this warning by setting the GPIO
to active-high in the GPIO specifier which aligns with the presense of
the 'enable-active-high' property.
Fixes: 3499359418 ("arm64: tegra: Enable HDMI on Jetson TX1")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Ensure PAN is re-enabled following user fault in uaccess routines
-----BEGIN PGP SIGNATURE-----
iQFEBAABCgAuFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAl3WdTEQHHdpbGxAa2Vy
bmVsLm9yZwAKCRC3rHDchMFjNE43B/9ow5C7aV1Jmb9dk3zfkDkVuviCkv9STpNW
YosKSAHwGvsfmBd/f+kd/ipqnt/fBLbXHqRderbayDW7xundCP8Qgl51N2RwJ92O
si3rPHW62xjbv0U3XqY9h74wH4jfox3KAT8c5EBcLuZtmV3gTb1txWDQ0PfQZMpN
0cmfTRPHB7LKJ/hupEyq6iVPYx+mV1ajenW1uzBOQhu+c8jC5Uf9kDn/D93rCYCg
7NL88odhP0Oyt6HDcR5LB+nl7fz+q0jXzxyF8qHDWNitV4aovU9rLMpDpn4YVvYd
DcFEyGdwYSxExLFrBuvmevZ7+2biT3qWQcPuNQGCcqWQSu38ULFK
=r7nI
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fix from Will Deacon:
"Ensure PAN is re-enabled following user fault in uaccess routines.
After I thought we were done for 5.4, we had a report this week of a
nasty issue that has been shown to leak data between different user
address spaces thanks to corruption of entries in the TLB. In
hindsight, we should have spotted this in review when the PAN code was
merged back in v4.3, but hindsight is 20/20 and I'm trying not to beat
myself up too much about it despite being fairly miserable.
Anyway, the fix is "obvious" but the actual failure is more more
subtle, and is described in the commit message. I've included a fairly
mechanical follow-up patch here as well, which moves this checking out
into the C wrappers which is what we do for {get,put}_user() already
and allows us to remove these bloody assembly macros entirely. The
patches have passed kernelci [1] [2] [3] and CKI [4] tests over night,
as well as some targetted testing [5] for this particular issue.
The first patch is tagged for stable and should be applied to 4.14,
4.19 and 5.3. I have separate backports for 4.4 and 4.9, which I'll
send out once this has landed in your tree (although the original
patch applies cleanly, it won't build for those two trees).
Thanks to Pavel Tatashin for reporting this and Mark Rutland for
helping to diagnose the issue and review/test the solution"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: uaccess: Remove uaccess_*_not_uao asm macros
arm64: uaccess: Ensure PAN is re-enabled after unhandled uaccess fault
It is safer and simpler to drop the uaccess assembly macros in favour of
inline C functions. Although this bloats the Image size slightly, it
aligns our user copy routines with '{get,put}_user()' and generally
makes the code a lot easier to reason about.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Pavel Tatashin <pasha.tatashin@soleen.com>
[will: tweaked commit message and changed temporary variable names]
Signed-off-by: Will Deacon <will@kernel.org>
A number of our uaccess routines ('__arch_clear_user()' and
'__arch_copy_{in,from,to}_user()') fail to re-enable PAN if they
encounter an unhandled fault whilst accessing userspace.
For CPUs implementing both hardware PAN and UAO, this bug has no effect
when both extensions are in use by the kernel.
For CPUs implementing hardware PAN but not UAO, this means that a kernel
using hardware PAN may execute portions of code with PAN inadvertently
disabled, opening us up to potential security vulnerabilities that rely
on userspace access from within the kernel which would usually be
prevented by this mechanism. In other words, parts of the kernel run the
same way as they would on a CPU without PAN implemented/emulated at all.
For CPUs not implementing hardware PAN and instead relying on software
emulation via 'CONFIG_ARM64_SW_TTBR0_PAN=y', the impact is unfortunately
much worse. Calling 'schedule()' with software PAN disabled means that
the next task will execute in the kernel using the page-table and ASID
of the previous process even after 'switch_mm()', since the actual
hardware switch is deferred until return to userspace. At this point, or
if there is a intermediate call to 'uaccess_enable()', the page-table
and ASID of the new process are installed. Sadly, due to the changes
introduced by KPTI, this is not an atomic operation and there is a very
small window (two instructions) where the CPU is configured with the
page-table of the old task and the ASID of the new task; a speculative
access in this state is disastrous because it would corrupt the TLB
entries for the new task with mappings from the previous address space.
As Pavel explains:
| I was able to reproduce memory corruption problem on Broadcom's SoC
| ARMv8-A like this:
|
| Enable software perf-events with PERF_SAMPLE_CALLCHAIN so userland's
| stack is accessed and copied.
|
| The test program performed the following on every CPU and forking
| many processes:
|
| unsigned long *map = mmap(NULL, PAGE_SIZE, PROT_READ|PROT_WRITE,
| MAP_SHARED | MAP_ANONYMOUS, -1, 0);
| map[0] = getpid();
| sched_yield();
| if (map[0] != getpid()) {
| fprintf(stderr, "Corruption detected!");
| }
| munmap(map, PAGE_SIZE);
|
| From time to time I was getting map[0] to contain pid for a
| different process.
Ensure that PAN is re-enabled when returning after an unhandled user
fault from our uaccess routines.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Cc: <stable@vger.kernel.org>
Fixes: 338d4f49d6 ("arm64: kernel: Add support for Privileged Access Never")
Signed-off-by: Pavel Tatashin <pasha.tatashin@soleen.com>
[will: rewrote commit message]
Signed-off-by: Will Deacon <will@kernel.org>
A set of fixes that have trickled in over the last couple of weeks:
- MAINTAINER update for Cavium/Marvell ThunderX2
- stm32 tweaks to pinmux for Joystick/Camera, and RAM allocation for CAN
interfaces
- i.MX fixes for voltage regulator GPIO mappings, fixes voltage scaling
issues
- More i.MX fixes for various issues on i.MX eval boards: interrupt
storm due to u-boot leaving pins in new states, fixing power button
config, a couple of compatible-string corrections.
- Powerdown and Suspend/Resume fixes for Allwinner A83-based tablets
- A few documentation tweaks and a fix of a memory leak in the reset
subsystem
-----BEGIN PGP SIGNATURE-----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=Ei7j
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"A set of fixes that have trickled in over the last couple of weeks:
- MAINTAINER update for Cavium/Marvell ThunderX2
- stm32 tweaks to pinmux for Joystick/Camera, and RAM allocation for
CAN interfaces
- i.MX fixes for voltage regulator GPIO mappings, fixes voltage
scaling issues
- More i.MX fixes for various issues on i.MX eval boards: interrupt
storm due to u-boot leaving pins in new states, fixing power button
config, a couple of compatible-string corrections.
- Powerdown and Suspend/Resume fixes for Allwinner A83-based tablets
- A few documentation tweaks and a fix of a memory leak in the reset
subsystem"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
MAINTAINERS: update Cavium ThunderX2 maintainers
ARM: dts: stm32: change joystick pinctrl definition on stm32mp157c-ev1
ARM: dts: stm32: remove OV5640 pinctrl definition on stm32mp157c-ev1
ARM: dts: stm32: Fix CAN RAM mapping on stm32mp157c
ARM: dts: stm32: relax qspi pins slew-rate for stm32mp157
arm64: dts: zii-ultra: fix ARM regulator GPIO handle
ARM: sunxi: Fix CPU powerdown on A83T
ARM: dts: sun8i-a83t-tbs-a711: Fix WiFi resume from suspend
arm64: dts: imx8mn: fix compatible string for sdma
arm64: dts: imx8mm: fix compatible string for sdma
reset: fix reset_control_ops kerneldoc comment
ARM: dts: imx6-logicpd: Re-enable SNVS power key
soc: imx: gpc: fix initialiser format
ARM: dts: imx6qdl-sabreauto: Fix storm of accelerometer interrupts
arm64: dts: ls1028a: fix a compatible issue
reset: fix reset_control_get_exclusive kerneldoc comment
reset: fix reset_control_lookup kerneldoc comment
reset: fix of_reset_control_get_count kerneldoc comment
reset: fix of_reset_simple_xlate kerneldoc comment
reset: Fix memory leak in reset_control_array_put()
Pull timer fixes from Thomas Gleixner:
"A small set of fixes for timekeepoing and clocksource drivers:
- VDSO data was updated conditional on the availability of a VDSO
capable clocksource. This causes the VDSO functions which do not
depend on a VDSO capable clocksource to operate on stale data.
Always update unconditionally.
- Prevent a double free in the mediatek driver
- Use the proper helper in the sh_mtu2 driver so it won't attempt to
initialize non-existing interrupts"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timekeeping/vsyscall: Update VDSO data unconditionally
clocksource/drivers/sh_mtu2: Do not loop using platform_get_irq_by_name()
clocksource/drivers/mediatek: Fix error handling
- Fix pte_same() to avoid getting stuck on write fault
-----BEGIN PGP SIGNATURE-----
iQFEBAABCgAuFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAl3FPbsQHHdpbGxAa2Vy
bmVsLm9yZwAKCRC3rHDchMFjNOkjB/9sNekV5x5vtLSXLPXH7TEt2jsKPHKHoc5h
i9bnpZc8na50Sj9V4ugMs4mqa5qOw+m2sJEHXxVr5k/bNJv3gqEpWAlnb4bXgjDj
yukM9FQVBRNMdDFeP3Yjm9VuoWhId0L9OfqCq/N6xi2kN3Xp60Ms7drYQeweBdEa
dBj4x52o/lMo3h5JF0QmWKTD85Nz0f4GxX4gclBMqsg/VAQOMDho86mMsfecwgCA
y9WbJClsH3nBcV8bChx0oSGzM+lJBmP6OnlxKM9tyzTmhJJQw4FDUmHmlaFptMe4
DRqJnVi41tzv7p8As/aE4sY7rnWEKaitn0r7gCfei+ACJG0Ezmas
=3M1Z
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fix from Will Deacon:
"Fix pte_same() to avoid getting stuck on write fault.
This single arm64 fix is a revert of 747a70e60b ("arm64: Fix
copy-on-write referencing in HugeTLB"), not because that patch was
wrong, but because it was broken by aa57157be6 ("arm64: Ensure
VM_WRITE|VM_SHARED ptes are clean by default") which we merged in
-rc6.
We spotted the issue in Android (AOSP), where one of the JIT threads
gets stuck on a write fault during boot because the faulting pte is
marked as PTE_DIRTY | PTE_WRITE | PTE_RDONLY and the fault handler
decides that there's nothing to do thanks to pte_same() masking out
PTE_RDONLY.
Thanks to John Stultz for reporting this and testing this so quickly,
and to Steve Capper for confirming that the HugeTLB tests continue to
pass"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Do not mask out PTE_RDONLY in pte_same()
Following commit 73e86cb03c ("arm64: Move PTE_RDONLY bit handling out
of set_pte_at()"), the PTE_RDONLY bit is no longer managed by
set_pte_at() but built into the PAGE_* attribute definitions.
Consequently, pte_same() must include this bit when checking two PTEs
for equality.
Remove the arm64-specific pte_same() function, practically reverting
commit 747a70e60b ("arm64: Fix copy-on-write referencing in HugeTLB")
Fixes: 73e86cb03c ("arm64: Move PTE_RDONLY bit handling out of set_pte_at()")
Cc: <stable@vger.kernel.org> # 4.14.x-
Cc: Will Deacon <will@kernel.org>
Cc: Steve Capper <steve.capper@arm.com>
Reported-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
The update of the VDSO data is depending on __arch_use_vsyscall() returning
True. This is a leftover from the attempt to map the features of various
architectures 1:1 into generic code.
The usage of __arch_use_vsyscall() in the actual vsyscall implementations
got dropped and replaced by the requirement for the architecture code to
return U64_MAX if the global clocksource is not usable in the VDSO.
But the __arch_use_vsyscall() check in the update code stayed which causes
the VDSO data to be stale or invalid when an architecture actually
implements that function and returns False when the current clocksource is
not usable in the VDSO.
As a consequence the VDSO implementations of clock_getres(), time(),
clock_gettime(CLOCK_.*_COARSE) operate on invalid data and return bogus
information.
Remove the __arch_use_vsyscall() check from the VDSO update function and
update the VDSO data unconditionally.
[ tglx: Massaged changelog and removed the now useless implementations in
asm-generic/ARM64/MIPS ]
Fixes: 44f57d788e ("timekeeping: Provide a generic update_vsyscall() implementation")
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Vincenzo Frascino <vincenzo.frascino@arm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/1571887709-11447-1-git-send-email-chenhc@lemote.com
- Fix the GPIO number that is controlling core voltage on
imx8mq-zii-ultra board.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdv+MuAAoJEFBXWFqHsHzOHzQH/Ayi4rrrHuInh7mCxSY2mXkH
iHO8iVKH5i+AvCfH66LpfdLFsKy+5L6WllRWDt3tvEjI9YCpBdHZrwuiBteh90K2
4J8vRNfLGhCqS7iRv17DuOIK0v9mC6mzbYg38xftSMDnNU0JanG0FSA6ztDuoKqZ
NjrUkECWSQeLbic9N2H27x0RUdMG/RE4F+q+rDnaTzgMdwrws+hSKdTfsnS8MUBc
NLnzwxoDjaB8rR6DKAM3xsQYEn9oT3cD2RDNJ2fBbp86XK9qTe5MNQlArp3grmHj
4zwZcrG1NAxHtQJv6kqCIRZ8FYSCSQQORekYucstm35knr/zAYv1XDPOqLkkFG0=
=0xmb
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-5.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.4, 3rd round:
- Fix the GPIO number that is controlling core voltage on
imx8mq-zii-ultra board.
* tag 'imx-fixes-5.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: zii-ultra: fix ARM regulator GPIO handle
Link: https://lore.kernel.org/r/20191104084513.GW24620@dragon
Signed-off-by: Olof Johansson <olof@lixom.net>
The GPIO handle is referencing the wrong GPIO, so the voltage did not
actually change as intended. The pinmux is already correct, so just
correct the GPIO number.
Fixes: 4a13b3bec3 (arm64: dts: imx: add Zii Ultra board support)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
- Get SNVS power key back to work for imx6-logicpd board. It was
accidentally disabled by commit 770856f0da ("ARM: dts: imx6qdl:
Enable SNVS power key according to board design").
- Fix sparse warnings in IMX GPC driver by making the initializers
in imx_gpc_domains C99 format.
- Fix an interrupt storm coming from accelerometer on imx6qdl-sabreauto
board. This is seen with upstream version U-Boot where pinctrl is not
configured for the device.
- Fix sdma device compatible string for i.MX8MM and i.MX8MN SoC.
- Fix compatible of PCA9547 i2c-mux on LS1028A QDS board to get the
device probed correctly.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdt+NxAAoJEFBXWFqHsHzO9dQIAItV9GBySkuQ74/LBBp9WHfi
Y708jUcbm/oEkic3bW+RdXpr+Xo3nP1E1VrdogqwWZStePS4JQtRWs7/+NAC/aiw
wrUDoCXnZYiSLtp+f/1OSs7mUSG13Ip+Um9VxjI1AI9ld1YKg8sSeg0Xlk5oNsk4
1/2c1P9nW0XjWMkpLqYzIbbtb+sisCX0/Ftyxw7vrjhpgJSDDUTE37IFgmdskZg6
ILl00chE4E+8AlLm9kdtqOgzihtFVbSIrhF99gbF6R9vZQGoYgOE3QM2YG+qhEOd
56bQTJJRVwutSbBGGv1ya/J5cmtZYDzoi10JEEQ+zkyrcU+G3qj9+8/wZORba5o=
=0kUv
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-5.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.4, 2nd round:
- Get SNVS power key back to work for imx6-logicpd board. It was
accidentally disabled by commit 770856f0da ("ARM: dts: imx6qdl:
Enable SNVS power key according to board design").
- Fix sparse warnings in IMX GPC driver by making the initializers
in imx_gpc_domains C99 format.
- Fix an interrupt storm coming from accelerometer on imx6qdl-sabreauto
board. This is seen with upstream version U-Boot where pinctrl is not
configured for the device.
- Fix sdma device compatible string for i.MX8MM and i.MX8MN SoC.
- Fix compatible of PCA9547 i2c-mux on LS1028A QDS board to get the
device probed correctly.
* tag 'imx-fixes-5.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: imx8mn: fix compatible string for sdma
arm64: dts: imx8mm: fix compatible string for sdma
ARM: dts: imx6-logicpd: Re-enable SNVS power key
soc: imx: gpc: fix initialiser format
ARM: dts: imx6qdl-sabreauto: Fix storm of accelerometer interrupts
arm64: dts: ls1028a: fix a compatible issue
Link: https://lore.kernel.org/r/20191029110334.GA20928@dragon
Signed-off-by: Olof Johansson <olof@lixom.net>
- Enable CPU errata workarounds for Broadcom Brahma-B53
- Enable CPU errata workarounds for Qualcomm Hydra/Kryo CPUs
- Fix initial dirty status of writeable, shared mappings
-----BEGIN PGP SIGNATURE-----
iQFEBAABCgAuFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAl28HzAQHHdpbGxAa2Vy
bmVsLm9yZwAKCRC3rHDchMFjNH3gB/4hJoYsASohxTVEcILOp7gZQZd4zgMuF16Z
ci9XcUgmpT3LNQTqSYASDxZZylVdK7eEq4yUXFpe57D5WL6GyEBLDWr09O6qb6F1
p/IuyEkUjram8GzRZsdW3/i786m887T1VYtRg6C7GKU9dHTRzkZcPTklWqc1CsEN
u7KqLGzWHxRNNUVWFhEsn9kTSARVOMfqXfERcpc2f6E5olXz8E62K+av2NL3u5o7
JQqHFqi5iJB66qc0AvUxc7oq/+Hvtz5nQfFm0IWQvGy3dvZ/vTGxYwAW2f7t70SH
MGHT+MsqYEENDjunMKtdHZ+D3A1xkYcrsKgOBkSBTTVlgrSonCr/
=0QZC
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"These are almost exclusively related to CPU errata in CPUs from
Broadcom and Qualcomm where the workarounds were either not being
enabled when they should have been or enabled when they shouldn't have
been.
The only "interesting" fix is ensuring that writeable, shared mappings
are initially mapped as clean since we inadvertently broke the logic
back in v4.14 and then noticed the problem via code inspection the
other day.
The only critical issue we have outstanding is a sporadic NULL
dereference in the scheduler, which doesn't appear to be
arm64-specific and PeterZ is tearing his hair out over it at the
moment.
Summary:
- Enable CPU errata workarounds for Broadcom Brahma-B53
- Enable CPU errata workarounds for Qualcomm Hydra/Kryo CPUs
- Fix initial dirty status of writeable, shared mappings"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: apply ARM64_ERRATUM_843419 workaround for Brahma-B53 core
arm64: Brahma-B53 is SSB and spectre v2 safe
arm64: apply ARM64_ERRATUM_845719 workaround for Brahma-B53 core
arm64: cpufeature: Enable Qualcomm Falkor errata 1009 for Kryo
arm64: cpufeature: Enable Qualcomm Falkor/Kryo errata 1003
arm64: Ensure VM_WRITE|VM_SHARED ptes are clean by default
The Broadcom Brahma-B53 core is susceptible to the issue described by
ARM64_ERRATUM_843419 so this commit enables the workaround to be applied
when executing on that core.
Since there are now multiple entries to match, we must convert the
existing ARM64_ERRATUM_843419 into an erratum list and use
cpucap_multi_entry_cap_matches to match our entries.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Will Deacon <will@kernel.org>
Add the Brahma-B53 CPU (all versions) to the whitelists of CPUs for the
SSB and spectre v2 mitigations.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Will Deacon <will@kernel.org>
The Broadcom Brahma-B53 core is susceptible to the issue described by
ARM64_ERRATUM_845719 so this commit enables the workaround to be applied
when executing on that core.
Since there are now multiple entries to match, we must convert the
existing ARM64_ERRATUM_845719 into an erratum list.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Will Deacon <will@kernel.org>
The Kryo cores share errata 1009 with Falkor, so add their model
definitions and enable it for them as well.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[will: Update entry in silicon-errata.rst]
Signed-off-by: Will Deacon <will@kernel.org>
With the introduction of 'cce360b54ce6 ("arm64: capabilities: Filter the
entries based on a given mask")' the Qualcomm Falkor/Kryo errata 1003 is
no long applied.
The result of not applying errata 1003 is that MSM8996 runs into various
RCU stalls and fails to boot most of the times.
Give 1003 a "type" to ensure they are not filtered out in
update_cpu_capabilities().
Fixes: cce360b54c ("arm64: capabilities: Filter the entries based on a given mask")
Cc: stable@vger.kernel.org
Reported-by: Mark Brown <broonie@kernel.org>
Suggested-by: Will Deacon <will@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Will Deacon <will@kernel.org>
Shared and writable mappings (__S.1.) should be clean (!dirty) initially
and made dirty on a subsequent write either through the hardware DBM
(dirty bit management) mechanism or through a write page fault. A clean
pte for the arm64 kernel is one that has PTE_RDONLY set and PTE_DIRTY
clear.
The PAGE_SHARED{,_EXEC} attributes have PTE_WRITE set (PTE_DBM) and
PTE_DIRTY clear. Prior to commit 73e86cb03c ("arm64: Move PTE_RDONLY
bit handling out of set_pte_at()"), it was the responsibility of
set_pte_at() to set the PTE_RDONLY bit and mark the pte clean if the
software PTE_DIRTY bit was not set. However, the above commit removed
the pte_sw_dirty() check and the subsequent setting of PTE_RDONLY in
set_pte_at() while leaving the PAGE_SHARED{,_EXEC} definitions
unchanged. The result is that shared+writable mappings are now dirty by
default
Fix the above by explicitly setting PTE_RDONLY in PAGE_SHARED{,_EXEC}.
In addition, remove the superfluous PTE_DIRTY bit from the kernel PROT_*
attributes.
Fixes: 73e86cb03c ("arm64: Move PTE_RDONLY bit handling out of set_pte_at()")
Cc: <stable@vger.kernel.org> # 4.14.x-
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
SDMA in i.MX8MN should use same configuration as i.MX8MQ
So need to change compatible string to be "fsl,imx8mq-sdma".
Fixes: 6c3debcbae ("arm64: dts: freescale: Add i.MX8MN dtsi support")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
SDMA in i.MX8MM should use same configuration as i.MX8MQ
So need to change compatible string to be "fsl,imx8mq-sdma".
Fixes: a05ea40eb3 ("arm64: dts: imx: Add i.mx8mm dtsi support")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
A slightly larger set of fixes have accrued in the last two weeks.
Mostly a collection of the usual smaller fixes:
- Marvell Armada: USB phy setup issues on Turris Mox
- Broadcom: GPIO/pinmux DT mapping corrections for Stingray, MMC bus
width fix for RPi Zero W, GPIO LED removal for RPI CM3. Also some
maintainer updates.
- OMAP: Fixlets for display config, interrupt settings for wifi, some
clock/PM pieces. Also IOMMU regression fix and a ti-sysc no-watchdog
regression fix.
- i.MX: A few fixes around PM/settings, some devicetree fixlets and
catching up with config option changes in DRM
- Rockchip: RockRro64 misc DT fixups, Hugsun X99 USB-C, Kevin display
panel settings
... and some smaller fixes for Davinci (backlight, McBSP DMA), Allwinner
(phy regulators, PMU removal on A64, etc).
-----BEGIN PGP SIGNATURE-----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=Jy/6
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"A slightly larger set of fixes have accrued in the last two weeks.
Mostly a collection of the usual smaller fixes:
- Marvell Armada: USB phy setup issues on Turris Mox
- Broadcom: GPIO/pinmux DT mapping corrections for Stingray, MMC bus
width fix for RPi Zero W, GPIO LED removal for RPI CM3. Also some
maintainer updates.
- OMAP: Fixlets for display config, interrupt settings for wifi, some
clock/PM pieces. Also IOMMU regression fix and a ti-sysc
no-watchdog regression fix.
- i.MX: A few fixes around PM/settings, some devicetree fixlets and
catching up with config option changes in DRM
- Rockchip: RockRro64 misc DT fixups, Hugsun X99 USB-C, Kevin display
panel settings
... and some smaller fixes for Davinci (backlight, McBSP DMA),
Allwinner (phy regulators, PMU removal on A64, etc)"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (42 commits)
ARM: dts: stm32: relax qspi pins slew-rate for stm32mp157
MAINTAINERS: Update the Spreadtrum SoC maintainer
MAINTAINERS: Remove Gregory and Brian for ARCH_BRCMSTB
ARM: dts: bcm2837-rpi-cm3: Avoid leds-gpio probing issue
bus: ti-sysc: Fix watchdog quirk handling
ARM: OMAP2+: Add pdata for OMAP3 ISP IOMMU
ARM: OMAP2+: Plug in device_enable/idle ops for IOMMUs
ARM: davinci_all_defconfig: enable GPIO backlight
ARM: davinci: dm365: Fix McBSP dma_slave_map entry
ARM: dts: bcm2835-rpi-zero-w: Fix bus-width of sdhci
ARM: imx_v6_v7_defconfig: Enable CONFIG_DRM_MSM
arm64: dts: imx8mn: Use correct clock for usdhc's ipg clk
arm64: dts: imx8mm: Use correct clock for usdhc's ipg clk
arm64: dts: imx8mq: Use correct clock for usdhc's ipg clk
ARM: dts: imx7s: Correct GPT's ipg clock source
ARM: dts: vf610-zii-scu4-aib: Specify 'i2c-mux-idle-disconnect'
ARM: dts: imx6q-logicpd: Re-Enable SNVS power key
arm64: dts: lx2160a: Correct CPU core idle state name
mailmap: Add Simon Arlott (replacement for expired email address)
arm64: dts: rockchip: Fix override mode for rk3399-kevin panel
...
The I2C multiplexer used on ls1028aqds is PCA9547, not PCA9847.
If the wrong compatible was used, this chip will not be able to
be probed correctly and hence fail to work.
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Fixes: 8897f3255c ("arm64: dts: Add support for NXP LS1028A SoC")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
- A fixup for the A10 CSI DT binding merged during the 5.4-rc1 window
- A fix for a dt-binding error
- Addition of phy regulator delays
- The PMU on the A64 was found to be non-functional, so we've dropped it for now
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXa/4RQAKCRDj7w1vZxhR
xU3XAQDYuCixpCCftKIhjcz+oultXqAJysDEE44dATwT1YfINgD/eBSwBw1l/Ni7
yOumUvRZ1fJC3NO8e7vh9cYN9yy5tgw=
=3/ru
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-5.4-1' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/fixes
A number of fixes for this release, but mostly:
- A fixup for the A10 CSI DT binding merged during the 5.4-rc1 window
- A fix for a dt-binding error
- Addition of phy regulator delays
- The PMU on the A64 was found to be non-functional, so we've dropped it for now
* tag 'sunxi-fixes-for-5.4-1' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun7i: Drop the module clock from the device tree
dt-bindings: media: sun4i-csi: Drop the module clock
media: dt-bindings: Fix building error for dt_binding_check
arm64: dts: allwinner: a64: sopine-baseboard: Add PHY regulator delay
arm64: dts: allwinner: a64: Drop PMU node
arm64: dts: allwinner: a64: pine64-plus: Add PHY regulator delay
Link: https://lore.kernel.org/r/80085a57-c40f-4bed-a9c3-19858d87564e.lettre@localhost
Signed-off-by: Olof Johansson <olof@lixom.net>
Special PMU edition:
- Fix cycle counter truncation
- Fix cycle counter overflow limit on pure 64bit system
- Allow chained events to be actually functional
- Correct sample period after overflow
-----BEGIN PGP SIGNATURE-----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=ORrS
-----END PGP SIGNATURE-----
Merge tag 'kvmarm-fixes-5.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/arm fixes for 5.4, take #2
Special PMU edition:
- Fix cycle counter truncation
- Fix cycle counter overflow limit on pure 64bit system
- Allow chained events to be actually functional
- Correct sample period after overflow
as well as a fix for the Gru-Kevin display override and fixing the dt-
binding for Theobroma boards to the correct naming that is also actually
used in the wild.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAl2tm/UQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgeUsB/4uN9dnY062/aFUBOpJx8dLL380YA/tVoFd
tLS1FSt5avkZi5cWZQrpmW+WqXyFZN1i4r6LMnDQmhmRvHiYBVSubLDmzlc2hXLH
m2OOm4+6ukAid1zQhYMSGl2ks3uz0gAesZ+EeLrzsyvA9xnS64a4HswEVRY5gAcN
VXA7gxY4kqnWPr88b/pZwwThGbcHIbT9vctHlicRgyhI8kqW0x/jNVzMnx+iaQwR
CQT6v0mDQhU2Ig03/TZmZmMNbdlR+qpmOhiSSuuttfElNCcrPjWxLMoZWshXnQ6s
ewKwc0JQ1jFlmel8tuPUvCnO39qVX7UixgFZBLTNn6gJFLlFVvFL
=Zs4u
-----END PGP SIGNATURE-----
Merge tag 'v5.4-rockchip-dtsfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/fixes
A number of fixes for individual boards like the rockpro64, and Hugsun X99
as well as a fix for the Gru-Kevin display override and fixing the dt-
binding for Theobroma boards to the correct naming that is also actually
used in the wild.
* tag 'v5.4-rockchip-dtsfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: Fix override mode for rk3399-kevin panel
arm64: dts: rockchip: Fix usb-c on Hugsun X99 TV Box
arm64: dts: rockchip: fix RockPro64 sdmmc settings
arm64: dts: rockchip: fix RockPro64 sdhci settings
arm64: dts: rockchip: fix RockPro64 vdd-log regulator settings
dt-bindings: arm: rockchip: fix Theobroma-System board bindings
arm64: dts: rockchip: fix Rockpro64 RK808 interrupt line
Link: https://lore.kernel.org/r/1599050.HRXuSXmxRg@phil
Signed-off-by: Olof Johansson <olof@lixom.net>
- Re-enable SNVS power key for imx6q-logicpd board which was accidentally
disabled by a SoC level change.
- Fix I2C switches on vf610-zii-scu4-aib board by specifying property
i2c-mux-idle-disconnect.
- A fix on imx-scu API that reads UID from firmware to avoid kernel NULL
pointer dump.
- A series from Anson to correct i.MX7 GPT and i.MX8 USDHC IPG clock.
- A fix on DRM_MSM Kconfig regression on i.MX5 by adding the option
explicitly into imx_v6_v7_defconfig.
- Fix ARM regulator states issue for zii-ultra board, which is impacting
stability of the board.
- A correction on CPU core idle state name for LayerScape LX2160A SoC.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdqHcmAAoJEFBXWFqHsHzOIqAIAJXqhCpbQkP5orCfXdFQxlvb
KpBiK0VEatMwPYAEm19Ij7/raFv+lRGIDo9ZyD9YGyDDIvOvRrSyeqDJCJSTEkol
QwTYl0KSNp2I4D7a0urcO4xMvcJt2QD2k3oe1Pe5mMDn5jbiMHAguUqrH96j/7zv
/9BE4n8aL9YBk6RE86YX0WMoDSfxToVQO+RQJ+7Yg66M83/9oUY3XqGv3svvZMD2
jsYtuHw8ounthr1OJSqcjUPTPLOCoEF+cG9HSkNmMCcShKNZ2wXIzvjeuBOdblKZ
MXnImEse4p7+81rsarGZLfj10tsfam4OibsgFqDIkgsT/aOdsOvXpjfp4/aO46Y=
=DFFA
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.4:
- Re-enable SNVS power key for imx6q-logicpd board which was accidentally
disabled by a SoC level change.
- Fix I2C switches on vf610-zii-scu4-aib board by specifying property
i2c-mux-idle-disconnect.
- A fix on imx-scu API that reads UID from firmware to avoid kernel NULL
pointer dump.
- A series from Anson to correct i.MX7 GPT and i.MX8 USDHC IPG clock.
- A fix on DRM_MSM Kconfig regression on i.MX5 by adding the option
explicitly into imx_v6_v7_defconfig.
- Fix ARM regulator states issue for zii-ultra board, which is impacting
stability of the board.
- A correction on CPU core idle state name for LayerScape LX2160A SoC.
* tag 'imx-fixes-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx_v6_v7_defconfig: Enable CONFIG_DRM_MSM
arm64: dts: imx8mn: Use correct clock for usdhc's ipg clk
arm64: dts: imx8mm: Use correct clock for usdhc's ipg clk
arm64: dts: imx8mq: Use correct clock for usdhc's ipg clk
ARM: dts: imx7s: Correct GPT's ipg clock source
ARM: dts: vf610-zii-scu4-aib: Specify 'i2c-mux-idle-disconnect'
ARM: dts: imx6q-logicpd: Re-Enable SNVS power key
arm64: dts: lx2160a: Correct CPU core idle state name
arm64: dts: zii-ultra: fix ARM regulator states
soc: imx: imx-scu: Getting UID from SCU should have response
Link: https://lore.kernel.org/r/20191017141851.GA22506@dragon
Signed-off-by: Olof Johansson <olof@lixom.net>
for 5.4, please pull the following:
- Rayangonda fixes the GPIO pins assignment for the Stringray SoCs
-----BEGIN PGP SIGNATURE-----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=0Eti
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.4/devicetree-arm64-fixes' of https://github.com/Broadcom/stblinux into arm/fixes
This pull request contains Broadcom ARM64-based SoCs Device Tree fixes
for 5.4, please pull the following:
- Rayangonda fixes the GPIO pins assignment for the Stringray SoCs
* tag 'arm-soc/for-5.4/devicetree-arm64-fixes' of https://github.com/Broadcom/stblinux:
arm64: dts: Fix gpio to pinmux mapping
Link: https://lore.kernel.org/r/20191015172356.9650-2-f.fainelli@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
Of PMCR_EL0.LC, the ARMv8 ARM says:
"In an AArch64 only implementation, this field is RES 1."
So be it.
Fixes: ab9468340d ("arm64: KVM: Add access handler for PMCR register")
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
- Work around Cavium/Marvell ThunderX2 erratum #219
- Fix regression in mlock() ABI caused by sign-extension of TTBR1 addresses
- More fixes to the spurious kernel fault detection logic
- Fix pathological preemption race when enabling some CPU features at boot
- Drop broken kcore macros in favour of generic implementations
- Fix userspace view of ID_AA64ZFR0_EL1 when SVE is disabled
- Avoid NULL dereference on allocation failure during hibernation
-----BEGIN PGP SIGNATURE-----
iQFEBAABCgAuFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAl2o1IsQHHdpbGxAa2Vy
bmVsLm9yZwAKCRC3rHDchMFjNEzXCACi8bK3PWUJ9R6DcUeDNFuSMT0d2C/8CRNj
mKnYkHx/GSChLBe3ZsNYbH5wnh70ItKzUUyMwMlwKevpr0kvLn0AN+WuSpP77Thk
qFuaO5EC10V039SXoAjOPs4Jxwoi6NaShDJYkLmr2kwp0g7dEol+8C80V1fQVqgx
oSmFcrYlqki1qhz8e1qCY4K8fAt6VdMt8OcouXs58ETFqsUFBFy/xx9Vsa0AQKkN
ZU8lzGIYNVLtA1G7wei7IuoKgYQ0t7XMynsve9P9i+RXmLrIbeyLpeZyn+3GW0jO
r3Epj0lYqKe8IZ+eTUDu3KvKHHdICHIDBDxP2c66hfgkw0prn/vU
=9E3e
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"The main thing here is a long-awaited workaround for a CPU erratum on
ThunderX2 which we have developed in conjunction with engineers from
Cavium/Marvell.
At the moment, the workaround is unconditionally enabled for affected
CPUs at runtime but we may add a command-line option to disable it in
future if performance numbers show up indicating a significant cost
for real workloads.
Summary:
- Work around Cavium/Marvell ThunderX2 erratum #219
- Fix regression in mlock() ABI caused by sign-extension of TTBR1 addresses
- More fixes to the spurious kernel fault detection logic
- Fix pathological preemption race when enabling some CPU features at boot
- Drop broken kcore macros in favour of generic implementations
- Fix userspace view of ID_AA64ZFR0_EL1 when SVE is disabled
- Avoid NULL dereference on allocation failure during hibernation"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: tags: Preserve tags for addresses translated via TTBR1
arm64: mm: fix inverted PAR_EL1.F check
arm64: sysreg: fix incorrect definition of SYS_PAR_EL1_F
arm64: entry.S: Do not preempt from IRQ before all cpufeatures are enabled
arm64: hibernate: check pgd table allocation
arm64: cpufeature: Treat ID_AA64ZFR0_EL1 as RAZ when SVE is not enabled
arm64: Fix kcore macros after 52-bit virtual addressing fallout
arm64: Allow CAVIUM_TX2_ERRATUM_219 to be selected
arm64: Avoid Cavium TX2 erratum 219 when switching TTBR
arm64: Enable workaround for Cavium TX2 erratum 219 when running SMT
arm64: KVM: Trap VM ops when ARM64_WORKAROUND_CAVIUM_TX2_219_TVM is set
Workaround for Cavium/Marvell ThunderX2 erratum #219.
* errata/tx2-219:
arm64: Allow CAVIUM_TX2_ERRATUM_219 to be selected
arm64: Avoid Cavium TX2 erratum 219 when switching TTBR
arm64: Enable workaround for Cavium TX2 erratum 219 when running SMT
arm64: KVM: Trap VM ops when ARM64_WORKAROUND_CAVIUM_TX2_219_TVM is set
Sign-extending TTBR1 addresses when converting to an untagged address
breaks the documented POSIX semantics for mlock() in some obscure error
cases where we end up returning -EINVAL instead of -ENOMEM as a direct
result of rewriting the upper address bits.
Rework the untagged_addr() macro to preserve the upper address bits for
TTBR1 addresses and only clear the tag bits for user addresses. This
matches the behaviour of the 'clear_address_tag' assembly macro, so
rename that and align the implementations at the same time so that they
use the same instruction sequences for the tag manipulation.
Link: https://lore.kernel.org/stable/20191014162651.GF19200@arrakis.emea.arm.com/
Reported-by: Jan Stancek <jstancek@redhat.com>
Tested-by: Jan Stancek <jstancek@redhat.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Tested-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Reviewed-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Will Deacon <will@kernel.org>
When detecting a spurious EL1 translation fault, we have the CPU retry
the translation using an AT S1E1R instruction, and inspect PAR_EL1 to
determine if the fault was spurious.
When PAR_EL1.F == 0, the AT instruction successfully translated the
address without a fault, which implies the original fault was spurious.
However, in this case we return false and treat the original fault as if
it was not spurious.
Invert the return value so that we treat such a case as spurious.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Fixes: 42f91093b0 ("arm64: mm: Ignore spurious translation faults taken from the kernel")
Tested-by: James Morse <james.morse@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
The 'F' field of the PAR_EL1 register lives in bit 0, not bit 1.
Fix the broken definition in 'sysreg.h'.
Fixes: e8620cff99 ("arm64: sysreg: Add some field definitions for PAR_EL1")
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Will Deacon <will@kernel.org>
Preempting from IRQ-return means that the task has its PSTATE saved
on the stack, which will get restored when the task is resumed and does
the actual IRQ return.
However, enabling some CPU features requires modifying the PSTATE. This
means that, if a task was scheduled out during an IRQ-return before all
CPU features are enabled, the task might restore a PSTATE that does not
include the feature enablement changes once scheduled back in.
* Task 1:
PAN == 0 ---| |---------------
| |<- return from IRQ, PSTATE.PAN = 0
| <- IRQ |
+--------+ <- preempt() +--
^
|
reschedule Task 1, PSTATE.PAN == 1
* Init:
--------------------+------------------------
^
|
enable_cpu_features
set PSTATE.PAN on all CPUs
Worse than this, since PSTATE is untouched when task switching is done,
a task missing the new bits in PSTATE might affect another task, if both
do direct calls to schedule() (outside of IRQ/exception contexts).
Fix this by preventing preemption on IRQ-return until features are
enabled on all CPUs.
This way the only PSTATE values that are saved on the stack are from
synchronous exceptions. These are expected to be fatal this early, the
exception is BRK for WARN_ON(), but as this uses do_debug_exception()
which keeps IRQs masked, it shouldn't call schedule().
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
[james: Replaced a really cool hack, with an even simpler static key in C.
expanded commit message with Julien's cover-letter ascii art]
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
There is a bug in create_safe_exec_page(), when page table is allocated
it is not checked that table is allocated successfully:
But it is dereferenced in: pgd_none(READ_ONCE(*pgdp)). Check that
allocation was successful.
Fixes: 82869ac57b ("arm64: kernel: Add support for hibernate/suspend-to-disk")
Reviewed-by: James Morse <james.morse@arm.com>
Signed-off-by: Pavel Tatashin <pasha.tatashin@soleen.com>
Signed-off-by: Will Deacon <will@kernel.org>
If CONFIG_ARM64_SVE=n then we fail to report ID_AA64ZFR0_EL1 as 0 when
read by userspace, despite being required by the architecture. Although
this is theoretically a change in ABI, userspace will first check for
the presence of SVE via the HWCAP or the ID_AA64PFR0_EL1.SVE field
before probing the ID_AA64ZFR0_EL1 register. Given that these are
reported correctly for this configuration, we can safely tighten up the
current behaviour.
Ensure ID_AA64ZFR0_EL1 is treated as RAZ when CONFIG_ARM64_SVE=n.
Signed-off-by: Julien Grall <julien.grall@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Dave Martin <dave.martin@arm.com>
Fixes: 06a916feca ("arm64: Expose SVE2 features for userspace")
Signed-off-by: Will Deacon <will@kernel.org>
On i.MX8MQ, usdhc's ipg clock is from IMX8MQ_CLK_IPG_ROOT,
assign it explicitly instead of using IMX8MQ_CLK_DUMMY.
Fixes: 748f908cc8 ("arm64: add basic DTS for i.MX8MQ")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
lx2160a support PW15 but not PW20, correct name to avoid confusing.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Fixes: 00c5ce8ac0 ("arm64: dts: lx2160a: add cpu idle support")
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Here are a lot of small USB driver fixes for 5.4-rc3.
syzbot has stepped up its testing of the USB driver stack, now able to
trigger fun race conditions between disconnect and probe functions.
Because of that we have a lot of fixes in here from Johan and others
fixing these reported issues that have been around since almost all
time.
We also are just deleting the rio500 driver, making all of the syzbot
bugs found in it moot as it turns out no one has been using it for years
as there is a userspace version that is being used instead.
There are also a number of other small fixes in here, all resolving
reported issues or regressions.
All have been in linux-next without any reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXaH78w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yk7mACgygFyLQ6GRUTTnGDcohZu44cuMO4AnR/MTrRq
/jiXPRUMsltMV7DHcq+S
=QX4p
-----END PGP SIGNATURE-----
Merge tag 'usb-5.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a lot of small USB driver fixes for 5.4-rc3.
syzbot has stepped up its testing of the USB driver stack, now able to
trigger fun race conditions between disconnect and probe functions.
Because of that we have a lot of fixes in here from Johan and others
fixing these reported issues that have been around since almost all
time.
We also are just deleting the rio500 driver, making all of the syzbot
bugs found in it moot as it turns out no one has been using it for
years as there is a userspace version that is being used instead.
There are also a number of other small fixes in here, all resolving
reported issues or regressions.
All have been in linux-next without any reported issues"
* tag 'usb-5.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (65 commits)
USB: yurex: fix NULL-derefs on disconnect
USB: iowarrior: use pr_err()
USB: iowarrior: drop redundant iowarrior mutex
USB: iowarrior: drop redundant disconnect mutex
USB: iowarrior: fix use-after-free after driver unbind
USB: iowarrior: fix use-after-free on release
USB: iowarrior: fix use-after-free on disconnect
USB: chaoskey: fix use-after-free on release
USB: adutux: fix use-after-free on release
USB: ldusb: fix NULL-derefs on driver unbind
USB: legousbtower: fix use-after-free on release
usb: cdns3: Fix for incorrect DMA mask.
usb: cdns3: fix cdns3_core_init_role()
usb: cdns3: gadget: Fix full-speed mode
USB: usb-skeleton: drop redundant in-urb check
USB: usb-skeleton: fix use-after-free after driver unbind
USB: usb-skeleton: fix NULL-deref on disconnect
usb:cdns3: Fix for CV CH9 running with g_zero driver.
usb: dwc3: Remove dev_err() on platform_get_irq() failure
usb: dwc3: Switch to platform_get_irq_byname_optional()
...
We export the entire kernel address space (i.e. the whole of the TTBR1
address range) via /proc/kcore. The kc_vaddr_to_offset() and
kc_offset_to_vaddr() macros are intended to convert between a kernel
virtual address and its offset relative to the start of the TTBR1
address space.
Prior to commit:
14c127c957 ("arm64: mm: Flip kernel VA space")
... the offset was calculated relative to VA_START, which at the time
was the start of the TTBR1 address space. At this time, PAGE_OFFSET
pointed to the high half of the TTBR1 address space where arm64's
linear map lived.
That commit swapped the position of VA_START and PAGE_OFFSET, but
failed to update kc_vaddr_to_offset() or kc_offset_to_vaddr(), so
since then the two macros behave incorrectly.
Note that VA_START was subsequently renamed to PAGE_END in commit:
77ad4ce693 ("arm64: memory: rename VA_START to PAGE_END")
As the generic implementations of the two macros calculate the offset
relative to PAGE_OFFSET (which is now the start of the TTBR1 address
space), we can delete the arm64 implementation and use those.
Fixes: 14c127c957 ("arm64: mm: Flip kernel VA space")
Reviewed-by: James Morse <james.morse@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Chris von Recklinghausen <crecklin@redhat.com>
Signed-off-by: Will Deacon <will@kernel.org>
Fix regression on USB for Turris Mox (Armada 3720 based board)
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCXaBBPwAKCRALBhiOFHI7
1dAaAJ94DyHYVx7+63dXJJnyC/elWJmvcQCgo3LYAK59aKX/upMYVtG9Swt0CsI=
=KyzY
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-5.4-1' of git://git.infradead.org/linux-mvebu into arm/fixes
mvebu fixes for 5.4 (part 1)
Fix regression on USB for Turris Mox (Armada 3720 based board)
* tag 'mvebu-fixes-5.4-1' of git://git.infradead.org/linux-mvebu:
arm64: dts: armada-3720-turris-mox: convert usb-phy to phy-supply
Link: https://lore.kernel.org/r/87blunsm43.fsf@FE-laptop
Signed-off-by: Olof Johansson <olof@lixom.net>
According to the RockPro64 schematic [1] the rk3399 sdmmc controller is
connected to a microSD (TF card) slot. Remove the cap-mmc-highspeed
property of the sdmmc controller, since no mmc card can be connected here.
[1] http://files.pine64.org/doc/rockpro64/rockpro64_v21-SCH.pdf
Fixes: e4f3fb4909 ("arm64: dts: rockchip: add initial dts support for Rockpro64")
Signed-off-by: Soeren Moch <smoch@web.de>
Link: https://lore.kernel.org/r/20191004203213.4995-1-smoch@web.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
- Numerous fixes to the compat vDSO build system, especially when
combining gcc and clang
- Fix parsing of PAR_EL1 in spurious kernel fault detection
- Partial workaround for Neoverse-N1 erratum #1542419
- Fix IRQ priority masking on entry from compat syscalls
- Fix advertisment of FRINT HWCAP to userspace
- Attempt to workaround inlining breakage with '__always_inline'
- Fix accidental freeing of parent SVE state on fork() error path
- Add some missing NULL pointer checks in instruction emulation init
- Some formatting and comment fixes
-----BEGIN PGP SIGNATURE-----
iQFEBAABCgAuFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAl2dv4cQHHdpbGxAa2Vy
bmVsLm9yZwAKCRC3rHDchMFjNO6UB/4yY3lYR6C++7EdVwYxQRXf8VX9ukeO76gp
P/AS6Kt8+AiOuhFJJXDj3D7K/KqgZnJEhzeWHTZluYpIBuzFerW+RxzmExL+wFWf
ISZgdh7roFCQx3Nt+iBs/bAMPvk5Da1KHvSw/yZ6P8mj6fK8sVUh/O8+KK4kSzfT
muDoSO6WHSonAEOYm9ryn1q1pM5DsCjr+9fm7d9L+dJAUP2xX44ymlIY+v6yD3Or
IWJMYaWKb4TbdTJSy2VbUSM0fzByGBJCx1wOTd4gV6uDbB4GA6h+E/DMB1qnvv9W
nH5c4qwVgYhp7prpescMxYZoV/I9damvfnaIjqh9jc3H3milEqcn
=GwLJ
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"A larger-than-usual batch of arm64 fixes for -rc3.
The bulk of the fixes are dealing with a bunch of issues with the
build system from the compat vDSO, which unfortunately led to some
significant Makefile rework to manage the horrible combinations of
toolchains that we can end up needing to drive simultaneously.
We came close to disabling the thing entirely, but Vincenzo was quick
to spin up some patches and I ended up picking up most of the bits
that were left [*]. Future work will look at disentangling the header
files properly.
Other than that, we have some important fixes all over, including one
papering over the miscompilation fallout from forcing
CONFIG_OPTIMIZE_INLINING=y, which I'm still unhappy about. Harumph.
We've still got a couple of open issues, so I'm expecting to have some
more fixes later this cycle.
Summary:
- Numerous fixes to the compat vDSO build system, especially when
combining gcc and clang
- Fix parsing of PAR_EL1 in spurious kernel fault detection
- Partial workaround for Neoverse-N1 erratum #1542419
- Fix IRQ priority masking on entry from compat syscalls
- Fix advertisment of FRINT HWCAP to userspace
- Attempt to workaround inlining breakage with '__always_inline'
- Fix accidental freeing of parent SVE state on fork() error path
- Add some missing NULL pointer checks in instruction emulation init
- Some formatting and comment fixes"
[*] Will's final fixes were
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Tested-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
but they were already in linux-next by then and he didn't rebase
just to add those.
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (21 commits)
arm64: armv8_deprecated: Checking return value for memory allocation
arm64: Kconfig: Make CONFIG_COMPAT_VDSO a proper Kconfig option
arm64: vdso32: Rename COMPATCC to CC_COMPAT
arm64: vdso32: Pass '--target' option to clang via VDSO_CAFLAGS
arm64: vdso32: Don't use KBUILD_CPPFLAGS unconditionally
arm64: vdso32: Move definition of COMPATCC into vdso32/Makefile
arm64: Default to building compat vDSO with clang when CONFIG_CC_IS_CLANG
lib: vdso: Remove CROSS_COMPILE_COMPAT_VDSO
arm64: vdso32: Remove jump label config option in Makefile
arm64: vdso32: Detect binutils support for dmb ishld
arm64: vdso: Remove stale files from old assembly implementation
arm64: vdso32: Fix broken compat vDSO build warnings
arm64: mm: fix spurious fault detection
arm64: ftrace: Ensure synchronisation in PLT setup for Neoverse-N1 #1542419
arm64: Fix incorrect irqflag restore for priority masking for compat
arm64: mm: avoid virt_to_phys(init_mm.pgd)
arm64: cpufeature: Effectively expose FRINT capability to userspace
arm64: Mark functions using explicit register variables as '__always_inline'
docs: arm64: Fix indentation and doc formatting
arm64/sve: Fix wrong free for task->thread.sve_state
...
Update Turris Mox device tree to use the phy-supply property of the
generic PHY framework instead of the legacy usb-phy property.
This is needed since it caused a regression on Turris Mox since "usb:
host: xhci-plat: Prevent an abnormally restrictive PHY init skipping".
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Fixes: eb6c2eb6c7 ("usb: host: xhci-plat: Prevent an abnormally restrictive PHY init skipping")
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
There are no return value checking when using kzalloc() and kcalloc() for
memory allocation. so add it.
Signed-off-by: Yunfeng Ye <yeyunfeng@huawei.com>
Signed-off-by: Will Deacon <will@kernel.org>
Allow the user to select the workaround for TX2-219, and update
the silicon-errata.rst file to reflect this.
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
As a PRFM instruction racing against a TTBR update can have undesirable
effects on TX2, NOP-out such PRFM on cores that are affected by
the TX2-219 erratum.
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
It appears that the only case where we need to apply the TX2_219_TVM
mitigation is when the core is in SMT mode. So let's condition the
enabling on detecting a CPU whose MPIDR_EL1.Aff0 is non-zero.
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
In order to workaround the TX2-219 erratum, it is necessary to trap
TTBRx_EL1 accesses to EL2. This is done by setting HCR_EL2.TVM on
guest entry, which has the side effect of trapping all the other
VM-related sysregs as well.
To minimize the overhead, a fast path is used so that we don't
have to go all the way back to the main sysreg handling code,
unless the rest of the hypervisor expects to see these accesses.
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
CONFIG_COMPAT_VDSO is defined by passing '-DCONFIG_COMPAT_VDSO' to the
compiler when the generic compat vDSO code is in use. It's much cleaner
and simpler to expose this as a proper Kconfig option (like x86 does),
so do that and remove the bodge.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
For consistency with CROSS_COMPILE_COMPAT, mechanically rename COMPATCC
to CC_COMPAT so that specifying aspects of the compat vDSO toolchain in
the environment isn't needlessly confusing.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Directly passing the '--target' option to clang by appending to
COMPATCC does not work if COMPATCC has been specified explicitly as
an argument to Make unless the 'override' directive is used, which is
ugly and different to what is done in the top-level Makefile.
Move the '--target' option for clang out of COMPATCC and into
VDSO_CAFLAGS, where it will be picked up when compiling and assembling
the 32-bit vDSO under clang.
Reported-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
KBUILD_CPPFLAGS is defined differently depending on whether the main
compiler is clang or not. This means that it is not possible to build
the compat vDSO with GCC if the rest of the kernel is built with clang.
Define VDSO_CPPFLAGS directly to break this dependency and allow a clang
kernel to build a compat vDSO with GCC:
$ make ARCH=arm64 CROSS_COMPILE=aarch64-linux-gnu- \
CROSS_COMPILE_COMPAT=arm-linux-gnueabihf- CC=clang \
COMPATCC=arm-linux-gnueabihf-gcc
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
There's no need to export COMPATCC, so just define it locally in the
vdso32/Makefile, which is the only place where it is used.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Rather than force the use of GCC for the compat cross-compiler, instead
extract the target from CROSS_COMPILE_COMPAT and pass it to clang if the
main compiler is clang.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
The jump labels are not used in vdso32 since it is not possible to run
runtime patching on them.
Remove the configuration option from the Makefile.
Cc: Will Deacon <will@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Older versions of binutils (prior to 2.24) do not support the "ISHLD"
option for memory barrier instructions, which leads to a build failure
when assembling the vdso32 library.
Add a compilation time mechanism that detects if binutils supports those
instructions and configure the kernel accordingly.
Cc: Will Deacon <will@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Will Deacon <will@kernel.org>
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Moving over to the generic C implementation of the vDSO inadvertently
left some stale files behind which are no longer used. Remove them.
Cc: Will Deacon <will@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
The .config file and the generated include/config/auto.conf can
end up out of sync after a set of commands since
CONFIG_CROSS_COMPILE_COMPAT_VDSO is not updated correctly.
The sequence can be reproduced as follows:
$ make ARCH=arm64 CROSS_COMPILE=aarch64-linux-gnu- defconfig
[...]
$ make ARCH=arm64 CROSS_COMPILE=aarch64-linux-gnu- menuconfig
[set CONFIG_CROSS_COMPILE_COMPAT_VDSO="arm-linux-gnueabihf-"]
$ make ARCH=arm64 CROSS_COMPILE=aarch64-linux-gnu-
Which results in:
arch/arm64/Makefile:62: CROSS_COMPILE_COMPAT not defined or empty,
the compat vDSO will not be built
even though the compat vDSO has been built:
$ file arch/arm64/kernel/vdso32/vdso.so
arch/arm64/kernel/vdso32/vdso.so: ELF 32-bit LSB pie executable, ARM,
EABI5 version 1 (SYSV), dynamically linked,
BuildID[sha1]=c67f6c786f2d2d6f86c71f708595594aa25247f6, stripped
A similar case that involves changing the configuration parameter
multiple times can be reconducted to the same family of problems.
Remove the use of CONFIG_CROSS_COMPILE_COMPAT_VDSO altogether and
instead rely on the cross-compiler prefix coming from the environment
via CROSS_COMPILE_COMPAT, much like we do for the rest of the kernel.
Cc: Will Deacon <will@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Will Deacon <will@kernel.org>
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
When detecting a spurious EL1 translation fault, we attempt to compare
ESR_EL1.DFSC with PAR_EL1.FST. We erroneously use FIELD_PREP() to
extract PAR_EL1.FST, when we should be using FIELD_GET().
In the wise words of Robin Murphy:
| FIELD_GET() is a UBFX, FIELD_PREP() is a BFI
Using FIELD_PREP() means that that dfsc & ESR_ELx_FSC_TYPE is always
zero, and hence not equal to ESR_ELx_FSC_FAULT. Thus we detect any
unhandled translation fault as spurious.
... so let's use FIELD_GET() to ensure we don't decide all translation
faults are spurious. ESR_EL1.DFSC occupies bits [5:0], and requires no
shifting.
Fixes: 42f91093b0 ("arm64: mm: Ignore spurious translation faults taken from the kernel")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reported-by: Robin Murphy <robin.murphy@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will.deacon@kernel.org>
Signed-off-by: Will Deacon <will@kernel.org>
The GPIO controlled regulator for the ARM power supply is supplying
the higher voltage when the GPIO is driven high. This is opposite to
the similar regulator setup on the EVK board and is impacting stability
of the board as the ARM domain has been supplied with a too low voltage
when to faster OPPs are in use.
Fixes: 4a13b3bec3 (arm64: dts: imx: add Zii Ultra board support)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
A few fixes this time around:
- Fixup of some clock specifications for DRA7 (device-tree fix)
- Removal of some dead/legacy CPU OPP/PM code for OMAP that throws
warnings at boot
- A few more minor fixups for OMAPs, most around display
- Enable STM32 QSPI as =y since their rootfs sometimes comes from
there
- Switch CONFIG_REMOTEPROC to =y since it went from tristate to bool
- Fix of thermal zone definition for ux500 (5.4 regression)
-----BEGIN PGP SIGNATURE-----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=+lB0
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"A few fixes this time around:
- Fixup of some clock specifications for DRA7 (device-tree fix)
- Removal of some dead/legacy CPU OPP/PM code for OMAP that throws
warnings at boot
- A few more minor fixups for OMAPs, most around display
- Enable STM32 QSPI as =y since their rootfs sometimes comes from
there
- Switch CONFIG_REMOTEPROC to =y since it went from tristate to bool
- Fix of thermal zone definition for ux500 (5.4 regression)"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: multi_v7_defconfig: Fix SPI_STM32_QSPI support
ARM: dts: ux500: Fix up the CPU thermal zone
arm64/ARM: configs: Change CONFIG_REMOTEPROC from m to y
ARM: dts: am4372: Set memory bandwidth limit for DISPC
ARM: OMAP2+: Fix warnings with broken omap2_set_init_voltage()
ARM: OMAP2+: Add missing LCDC midlemode for am335x
ARM: OMAP2+: Fix missing reset done flag for am3 and am43
ARM: dts: Fix gpio0 flags for am335x-icev2
ARM: omap2plus_defconfig: Enable more droid4 devices as loadable modules
ARM: omap2plus_defconfig: Enable DRM_TI_TFP410
DTS: ARM: gta04: introduce legacy spi-cs-high to make display work again
ARM: dts: Fix wrong clocks for dra7 mcasp
clk: ti: dra7: Fix mcasp8 clock bits
The RockPro64 schematic [1] page 18 states a min voltage of 0.8V and a
max voltage of 1.4V for the VDD_LOG pwm regulator. However, there is an
additional note that the pwm parameter needs to be modified.
From the schematics a voltage range of 0.8V to 1.7V can be calculated.
Additional voltage measurements on the board show that this fix indeed
leads to the correct voltage, while without this fix the voltage was set
too high.
[1] http://files.pine64.org/doc/rockpro64/rockpro64_v21-SCH.pdf
Fixes: e4f3fb4909 ("arm64: dts: rockchip: add initial dts support for Rockpro64")
Signed-off-by: Soeren Moch <smoch@web.de>
Link: https://lore.kernel.org/r/20191003215036.15023-1-smoch@web.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
a nested hypervisor has always been busted on Broadwell and newer processors,
and that has finally been fixed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJdlzTRAAoJEL/70l94x66DElcH/Rvhn5VQE/n2J+tKEXAICxQu
FqcTBJ5x2mp04aFe7xD3kWoKRJmz2lmHdw2ahFd4sqqLfGEFF/KW24ADI33vzLx/
UmT78O0Je3PX77TRnEXy+napbJny0iT6ikTAQKPbyQ151JlqlbPvatpDXXLPWQHv
jj6nKHCvMBrhV3kgaXO3cTFl8swX1hvR9lo9PcA2gRNt+HMN0heUmpfKughPoOes
JH+UNjsEr7MYlXYlIIc9o71EYH+kgPObwlLejy0ture+dvvZEJUJjZJE8H/XG5f2
ryXG9favaCOTAvaGf0R5Es+47A3crqUr6gHS0N28QKPn7x4hehIkKpA9dXQnWIw=
=1/LN
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"ARM and x86 bugfixes of all kinds.
The most visible one is that migrating a nested hypervisor has always
been busted on Broadwell and newer processors, and that has finally
been fixed"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (22 commits)
KVM: x86: omit "impossible" pmu MSRs from MSR list
KVM: nVMX: Fix consistency check on injected exception error code
KVM: x86: omit absent pmu MSRs from MSR list
selftests: kvm: Fix libkvm build error
kvm: vmx: Limit guest PMCs to those supported on the host
kvm: x86, powerpc: do not allow clearing largepages debugfs entry
KVM: selftests: x86: clarify what is reported on KVM_GET_MSRS failure
KVM: VMX: Set VMENTER_L1D_FLUSH_NOT_REQUIRED if !X86_BUG_L1TF
selftests: kvm: add test for dirty logging inside nested guests
KVM: x86: fix nested guest live migration with PML
KVM: x86: assign two bits to track SPTE kinds
KVM: x86: Expose XSAVEERPTR to the guest
kvm: x86: Enumerate support for CLZERO instruction
kvm: x86: Use AMD CPUID semantics for AMD vCPUs
kvm: x86: Improve emulation of CPUID leaves 0BH and 1FH
KVM: X86: Fix userspace set invalid CR4
kvm: x86: Fix a spurious -E2BIG in __do_cpuid_func
KVM: LAPIC: Loosen filter for adaptive tuning of lapic_timer_advance_ns
KVM: arm/arm64: vgic: Use the appropriate TRACE_INCLUDE_PATH
arm64: KVM: Kill hyp_alternate_select()
...
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRTLbB6QfY48x44uB6AXGG7T9hjvgUCXZbQhwAKCRCAXGG7T9hj
vh03AP9mOLNY8r16u6a+Iy0YVccTaeiQiquG6HgFVEGX2Ki38gD/Xf5u6bPRYBts
uSRL/eYDvtfU4YGGMjogn20Fdzhc5Ak=
=EkVp
-----END PGP SIGNATURE-----
Merge tag 'for-linus-5.4-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes and cleanups from Juergen Gross:
- a fix in the Xen balloon driver avoiding hitting a BUG_ON() in some
cases, plus a follow-on cleanup series for that driver
- a patch for introducing non-blocking EFI callbacks in Xen's EFI
driver, plu a cleanup patch for Xen EFI handling merging the x86 and
ARM arch specific initialization into the Xen EFI driver
- a fix of the Xen xenbus driver avoiding a self-deadlock when cleaning
up after a user process has died
- a fix for Xen on ARM after removal of ZONE_DMA
- a cleanup patch for avoiding build warnings for Xen on ARM
* tag 'for-linus-5.4-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/xenbus: fix self-deadlock after killing user process
xen/efi: have a common runtime setup function
arm: xen: mm: use __GPF_DMA32 for arm64
xen/balloon: Clear PG_offline in balloon_retrieve()
xen/balloon: Mark pages PG_offline in balloon_append()
xen/balloon: Drop __balloon_append()
xen/balloon: Set pages PageOffline() in balloon_add_region()
ARM: xen: unexport HYPERVISOR_platform_op function
xen/efi: Set nonblocking callbacks
This reverts commits 3d109bdca9 ("ARM: dts: sunxi: Remove useless
phy-names from EHCI and OHCI"), 0a3df8bb6d ("ARM: dts: sunxi: h3/h5:
Remove useless phy-names from EHCI and OHCI") and 3c7ab90aaa ("arm64:
dts: allwinner: Remove useless phy-names from EHCI and OHCI").
It turns out that while the USB bindings were not mentionning it, the PHY
client bindings were mandating that phy-names is set when phys is. Let's
add it back.
Fixes: 3d109bdca9 ("ARM: dts: sunxi: Remove useless phy-names from EHCI and OHCI")
Fixes: 0a3df8bb6d ("ARM: dts: sunxi: h3/h5: Remove useless phy-names from EHCI and OHCI")
Fixes: 3c7ab90aaa ("arm64: dts: allwinner: Remove useless phy-names from EHCI and OHCI")
Reported-by: Emmanuel Vadot <manu@bidouilliste.com>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20191002112651.100504-1-mripard@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CPUs affected by Neoverse-N1 #1542419 may execute a stale instruction if
it was recently modified. The affected sequence requires freshly written
instructions to be executable before a branch to them is updated.
There are very few places in the kernel that modify executable text,
all but one come with sufficient synchronisation:
* The module loader's flush_module_icache() calls flush_icache_range(),
which does a kick_all_cpus_sync()
* bpf_int_jit_compile() calls flush_icache_range().
* Kprobes calls aarch64_insn_patch_text(), which does its work in
stop_machine().
* static keys and ftrace both patch between nops and branches to
existing kernel code (not generated code).
The affected sequence is the interaction between ftrace and modules.
The module PLT is cleaned using __flush_icache_range() as the trampoline
shouldn't be executable until we update the branch to it.
Drop the double-underscore so that this path runs kick_all_cpus_sync()
too.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Commit bd82d4bd21 ("arm64: Fix incorrect irqflag restore for priority
masking") added a macro to the entry.S call paths that leave the
PSTATE.I bit set. This tells the pPNMI masking logic that interrupts
are masked by the CPU, not by the PMR. This value is read back by
local_daif_save().
Commit bd82d4bd21 added this call to el0_svc, as el0_svc_handler
is called with interrupts masked. el0_svc_compat was missed, but should
be covered in the same way as both of these paths end up in
el0_svc_common(), which expects to unmask interrupts.
Fixes: bd82d4bd21 ("arm64: Fix incorrect irqflag restore for priority masking")
Signed-off-by: James Morse <james.morse@arm.com>
Cc: Julien Thierry <julien.thierry.kdev@gmail.com>
Signed-off-by: Will Deacon <will@kernel.org>
If we take an unhandled fault in the kernel, we call show_pte() to dump
the {PGDP,PGD,PUD,PMD,PTE} values for the corresponding page table walk,
where the PGDP value is virt_to_phys(mm->pgd).
The boot-time and runtime kernel page tables, init_pg_dir and
swapper_pg_dir respectively, are kernel symbols. Thus, it is not valid
to call virt_to_phys() on either of these, though we'll do so if we take
a fault on a TTBR1 address.
When CONFIG_DEBUG_VIRTUAL is not selected, virt_to_phys() will silently
fix this up. However, when CONFIG_DEBUG_VIRTUAL is selected, this
results in splats as below. Depending on when these occur, they can
happen to suppress information needed to debug the original unhandled
fault, such as the backtrace:
| Unable to handle kernel paging request at virtual address ffff7fffec73cf0f
| Mem abort info:
| ESR = 0x96000004
| EC = 0x25: DABT (current EL), IL = 32 bits
| SET = 0, FnV = 0
| EA = 0, S1PTW = 0
| Data abort info:
| ISV = 0, ISS = 0x00000004
| CM = 0, WnR = 0
| ------------[ cut here ]------------
| virt_to_phys used for non-linear address: 00000000102c9dbe (swapper_pg_dir+0x0/0x1000)
| WARNING: CPU: 1 PID: 7558 at arch/arm64/mm/physaddr.c:15 __virt_to_phys+0xe0/0x170 arch/arm64/mm/physaddr.c:12
| Kernel panic - not syncing: panic_on_warn set ...
| SMP: stopping secondary CPUs
| Dumping ftrace buffer:
| (ftrace buffer empty)
| Kernel Offset: disabled
| CPU features: 0x0002,23000438
| Memory Limit: none
| Rebooting in 1 seconds..
We can avoid this by ensuring that we call __pa_symbol() for
init_mm.pgd, as this will always be a kernel symbol. As the dumped
{PGD,PUD,PMD,PTE} values are the raw values from the relevant entries we
don't need to handle these specially.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
The HWCAP framework will detect a new capability based on the sanitized
version of the ID registers.
Sanitization is based on a whitelist, so any field not described will end
up to be zeroed.
At the moment, ID_AA64ISAR1_EL1.FRINTTS is not described in
ftr_id_aa64isar1. This means the field will be zeroed and therefore the
userspace will not be able to see the HWCAP even if the hardware
supports the feature.
This can be fixed by describing the field in ftr_id_aa64isar1.
Fixes: ca9503fc9e ("arm64: Expose FRINT capabilities to userspace")
Signed-off-by: Julien Grall <julien.grall@arm.com>
Cc: mark.brown@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
As of ac7c3e4ff4 ("compiler: enable CONFIG_OPTIMIZE_INLINING forcibly"),
inline functions are no longer annotated with '__always_inline', which
allows the compiler to decide whether inlining is really a good idea or
not. Although this is a great idea on paper, the reality is that AArch64
GCC prior to 9.1 has been shown to get confused when creating an
out-of-line copy of a function passing explicit 'register' variables
into an inline assembly block:
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=91111
It's not clear whether this is specific to arm64 or not but, for now,
ensure that all of our functions using 'register' variables are marked
as '__always_inline' so that the old behaviour is effectively preserved.
Hopefully other architectures are luckier with their compilers.
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Will Deacon <will@kernel.org>
Fix the pinctrl and interrupt specifier for RK808 to use GPIO3_B2. On the
Rockpro64 schematic [1] page 16, it shows GPIO3_B2 used for the interrupt
line PMIC_INT_L from the RK808, and there's a note which translates as:
"PMU termination GPIO1_C5 changed to this".
Tested by setting an RTC wakealarm and checking /proc/interrupts counters.
Without this patch, neither the rockchip_gpio_irq counter for the RK808,
nor the RTC alarm counter increment when the alarm time is reached.
With this patch, both interrupt counters increment by 1 as expected.
[1] http://files.pine64.org/doc/rockpro64/rockpro64_v21-SCH.pdf
Fixes: e4f3fb4909 ("arm64: dts: rockchip: add initial dts support for Rockpro64")
Signed-off-by: Hugh Cole-Baker <sigmaris@gmail.com>
Link: https://lore.kernel.org/r/20190921131457.36258-1-sigmaris@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
- Remove the now obsolete hyp_alternate_select construct
- Fix the TRACE_INCLUDE_PATH macro in the vgic code
-----BEGIN PGP SIGNATURE-----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=9luB
-----END PGP SIGNATURE-----
Merge tag 'kvmarm-fixes-5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/arm fixes for 5.4, take #1
- Remove the now obsolete hyp_alternate_select construct
- Fix the TRACE_INCLUDE_PATH macro in the vgic code
Today the EFI runtime functions are setup in architecture specific
code (x86 and arm), with the functions themselves living in drivers/xen
as they are not architecture dependent.
As the setup is exactly the same for arm and x86 move the setup to
drivers/xen, too. This at once removes the need to make the single
functions global visible.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
[boris: "Dropped EXPORT_SYMBOL_GPL(xen_efi_runtime_setup)"]
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
The system which has SVE feature crashed because of
the memory pointed by task->thread.sve_state was destroyed
by someone.
That is because sve_state is freed while the forking the
child process. The child process has the pointer of sve_state
which is same as the parent's because the child's task_struct
is copied from the parent's one. If the copy_process()
fails as an error on somewhere, for example, copy_creds(),
then the sve_state is freed even if the parent is alive.
The flow is as follows.
copy_process
p = dup_task_struct
=> arch_dup_task_struct
*dst = *src; // copy the entire region.
:
retval = copy_creds
if (retval < 0)
goto bad_fork_free;
:
bad_fork_free:
...
delayed_free_task(p);
=> free_task
=> arch_release_task_struct
=> fpsimd_release_task
=> __sve_free
=> kfree(task->thread.sve_state);
// free the parent's sve_state
Move child's sve_state = NULL and clearing TIF_SVE flag
to arch_dup_task_struct() so that the child doesn't free the
parent's one.
There is no need to wait until copy_process() to clear TIF_SVE for
dst, because the thread flags for dst are initialized already by
copying the src task_struct.
This change simplifies the code, so get rid of comments that are no
longer needed.
As a note, arm64 used to have thread_info on the stack. So it
would not be possible to clear TIF_SVE until the stack is initialized.
From commit c02433dd6d ("arm64: split thread_info from task stack"),
the thread_info is part of the task, so it should be valid to modify
the flag from arch_dup_task_struct().
Cc: stable@vger.kernel.org # 4.15.x-
Fixes: bc0ee47603 ("arm64/sve: Core task context handling")
Signed-off-by: Masayoshi Mizuma <m.mizuma@jp.fujitsu.com>
Reported-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Suggested-by: Dave Martin <Dave.Martin@arm.com>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Tested-by: Julien Grall <julien.grall@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Commit 73f3816609 ("arm64: Advertise mitigation of Spectre-v2, or lack
thereof") renamed the caller of the install_bp_hardening_cb() function
but forgot to update a comment, which can be confusing when trying to
follow the code flow.
Fixes: 73f3816609 ("arm64: Advertise mitigation of Spectre-v2, or lack thereof")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Will Deacon <will@kernel.org>
There are total of 151 non-secure gpio (0-150) and four
pins of pinmux (91, 92, 93 and 94) are not mapped to any
gpio pin, hence update same in DT.
Fixes: 8aa428cc1e ("arm64: dts: Add pinctrl DT nodes for Stingray SOC")
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
It turns out that sopine-baseboard needs same fix as pine64-plus
for ethernet PHY. Here too Realtek ethernet PHY chip needs additional
power on delay to properly initialize. Datasheet mentions that chip
needs 30 ms to be properly powered on and that it needs some more time
to be initialized.
Fix that by adding 100ms ramp delay to regulator responsible for
powering PHY.
Note that issue was found out and fix tested on pine64-lts, but it's
basically the same as sopine-baseboard, only layout and connectors
differ.
Fixes: bdfe4cebea ("arm64: allwinner: a64: add Ethernet PHY regulator for several boards")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Looks like PMU in A64 is broken, it generates no interrupts at all and
as result 'perf top' shows no events.
Tested on Pine64-LTS.
Fixes: 34a97fcc71 ("arm64: dts: allwinner: a64: Add PMU node")
Cc: Harald Geyer <harald@ccbib.org>
Cc: Jared D. McNeill <jmcneill@NetBSD.org>
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Emmanuel Vadot <manu@FreeBSD.org>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Depending on kernel and bootloader configuration, it's possible that
Realtek ethernet PHY isn't powered on properly. According to the
datasheet, it needs 30ms to power up and then some more time before it
can be used.
Fix that by adding 100ms ramp delay to regulator responsible for
powering PHY.
Fixes: 94dcfdc77f ("arm64: allwinner: pine64-plus: Enable dwmac-sun8i")
Suggested-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Commit 6334150e9a ("remoteproc: don't allow modular build")
changes CONFIG_REMOTEPROC to a boolean from a tristate config
option which inhibits all defconfigs marking CONFIG_REMOTEPROC as
a module in compiling the remoteproc and dependent config options.
So fix the configs to have CONFIG_REMOTEPROC built in.
Link: https://lore.kernel.org/r/20190920075946.13282-5-j-keerthy@ti.com
Fixes: 6334150e9a ("remoteproc: don't allow modular build")
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Will Deacon <will@kernel.org>
[olof: Fixed up all 4 occurrances in this one commit]
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull kernel lockdown mode from James Morris:
"This is the latest iteration of the kernel lockdown patchset, from
Matthew Garrett, David Howells and others.
From the original description:
This patchset introduces an optional kernel lockdown feature,
intended to strengthen the boundary between UID 0 and the kernel.
When enabled, various pieces of kernel functionality are restricted.
Applications that rely on low-level access to either hardware or the
kernel may cease working as a result - therefore this should not be
enabled without appropriate evaluation beforehand.
The majority of mainstream distributions have been carrying variants
of this patchset for many years now, so there's value in providing a
doesn't meet every distribution requirement, but gets us much closer
to not requiring external patches.
There are two major changes since this was last proposed for mainline:
- Separating lockdown from EFI secure boot. Background discussion is
covered here: https://lwn.net/Articles/751061/
- Implementation as an LSM, with a default stackable lockdown LSM
module. This allows the lockdown feature to be policy-driven,
rather than encoding an implicit policy within the mechanism.
The new locked_down LSM hook is provided to allow LSMs to make a
policy decision around whether kernel functionality that would allow
tampering with or examining the runtime state of the kernel should be
permitted.
The included lockdown LSM provides an implementation with a simple
policy intended for general purpose use. This policy provides a coarse
level of granularity, controllable via the kernel command line:
lockdown={integrity|confidentiality}
Enable the kernel lockdown feature. If set to integrity, kernel features
that allow userland to modify the running kernel are disabled. If set to
confidentiality, kernel features that allow userland to extract
confidential information from the kernel are also disabled.
This may also be controlled via /sys/kernel/security/lockdown and
overriden by kernel configuration.
New or existing LSMs may implement finer-grained controls of the
lockdown features. Refer to the lockdown_reason documentation in
include/linux/security.h for details.
The lockdown feature has had signficant design feedback and review
across many subsystems. This code has been in linux-next for some
weeks, with a few fixes applied along the way.
Stephen Rothwell noted that commit 9d1f8be5cf ("bpf: Restrict bpf
when kernel lockdown is in confidentiality mode") is missing a
Signed-off-by from its author. Matthew responded that he is providing
this under category (c) of the DCO"
* 'next-lockdown' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (31 commits)
kexec: Fix file verification on S390
security: constify some arrays in lockdown LSM
lockdown: Print current->comm in restriction messages
efi: Restrict efivar_ssdt_load when the kernel is locked down
tracefs: Restrict tracefs when the kernel is locked down
debugfs: Restrict debugfs when the kernel is locked down
kexec: Allow kexec_file() with appropriate IMA policy when locked down
lockdown: Lock down perf when in confidentiality mode
bpf: Restrict bpf when kernel lockdown is in confidentiality mode
lockdown: Lock down tracing and perf kprobes when in confidentiality mode
lockdown: Lock down /proc/kcore
x86/mmiotrace: Lock down the testmmiotrace module
lockdown: Lock down module params that specify hardware parameters (eg. ioport)
lockdown: Lock down TIOCSSERIAL
lockdown: Prohibit PCMCIA CIS storage when the kernel is locked down
acpi: Disable ACPI table override if the kernel is locked down
acpi: Ignore acpi_rsdp kernel param when the kernel has been locked down
ACPI: Limit access to custom_method when the kernel is locked down
x86/msr: Restrict MSR access when the kernel is locked down
x86: Lock down IO port access when the kernel is locked down
...
The naming of pgtable_page_{ctor,dtor}() seems to have confused a few
people, and until recently arm64 used these erroneously/pointlessly for
other levels of page table.
To make it incredibly clear that these only apply to the PTE level, and to
align with the naming of pgtable_pmd_page_{ctor,dtor}(), let's rename them
to pgtable_pte_page_{ctor,dtor}().
These changes were generated with the following shell script:
----
git grep -lw 'pgtable_page_.tor' | while read FILE; do
sed -i '{s/pgtable_page_ctor/pgtable_pte_page_ctor/}' $FILE;
sed -i '{s/pgtable_page_dtor/pgtable_pte_page_dtor/}' $FILE;
done
----
... with the documentation re-flowed to remain under 80 columns, and
whitespace fixed up in macros to keep backslashes aligned.
There should be no functional change as a result of this patch.
Link: http://lkml.kernel.org/r/20190722141133.3116-1-mark.rutland@arm.com
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Mike Rapoport <rppt@linux.ibm.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Yu Zhao <yuzhao@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge updates from Andrew Morton:
- a few hot fixes
- ocfs2 updates
- almost all of -mm (slab-generic, slab, slub, kmemleak, kasan,
cleanups, debug, pagecache, memcg, gup, pagemap, memory-hotplug,
sparsemem, vmalloc, initialization, z3fold, compaction, mempolicy,
oom-kill, hugetlb, migration, thp, mmap, madvise, shmem, zswap,
zsmalloc)
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (132 commits)
mm/zsmalloc.c: fix a -Wunused-function warning
zswap: do not map same object twice
zswap: use movable memory if zpool support allocate movable memory
zpool: add malloc_support_movable to zpool_driver
shmem: fix obsolete comment in shmem_getpage_gfp()
mm/madvise: reduce code duplication in error handling paths
mm: mmap: increase sockets maximum memory size pgoff for 32bits
mm/mmap.c: refine find_vma_prev() with rb_last()
riscv: make mmap allocation top-down by default
mips: use generic mmap top-down layout and brk randomization
mips: replace arch specific way to determine 32bit task with generic version
mips: adjust brk randomization offset to fit generic version
mips: use STACK_TOP when computing mmap base address
mips: properly account for stack randomization and stack guard gap
arm: use generic mmap top-down layout and brk randomization
arm: use STACK_TOP when computing mmap base address
arm: properly account for stack randomization and stack guard gap
arm64, mm: make randomization selected by generic topdown mmap layout
arm64, mm: move generic mmap layout functions to mm
arm64: consider stack randomization for mmap base only when necessary
...
This commits selects ARCH_HAS_ELF_RANDOMIZE when an arch uses the generic
topdown mmap layout functions so that this security feature is on by
default.
Note that this commit also removes the possibility for arm64 to have elf
randomization and no MMU: without MMU, the security added by randomization
is worth nothing.
Link: http://lkml.kernel.org/r/20190730055113.23635-6-alex@ghiti.fr
Signed-off-by: Alexandre Ghiti <alex@ghiti.fr>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Luis Chamberlain <mcgrof@kernel.org>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
arm64 handles top-down mmap layout in a way that can be easily reused by
other architectures, so make it available in mm. It then introduces a new
config ARCH_WANT_DEFAULT_TOPDOWN_MMAP_LAYOUT that can be set by other
architectures to benefit from those functions. Note that this new config
depends on MMU being enabled, if selected without MMU support, a warning
will be thrown.
Link: http://lkml.kernel.org/r/20190730055113.23635-5-alex@ghiti.fr
Signed-off-by: Alexandre Ghiti <alex@ghiti.fr>
Suggested-by: Christoph Hellwig <hch@infradead.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Luis Chamberlain <mcgrof@kernel.org>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: James Hogan <jhogan@kernel.org>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Do not offset mmap base address because of stack randomization if current
task does not want randomization. Note that x86 already implements this
behaviour.
Link: http://lkml.kernel.org/r/20190730055113.23635-4-alex@ghiti.fr
Signed-off-by: Alexandre Ghiti <alex@ghiti.fr>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Luis Chamberlain <mcgrof@kernel.org>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Each architecture has its own way to determine if a task is a compat task,
by using is_compat_task in arch_mmap_rnd, it allows more genericity and
then it prepares its moving to mm/.
Link: http://lkml.kernel.org/r/20190730055113.23635-3-alex@ghiti.fr
Signed-off-by: Alexandre Ghiti <alex@ghiti.fr>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Luis Chamberlain <mcgrof@kernel.org>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Both pgtable_cache_init() and pgd_cache_init() are used to initialize kmem
cache for page table allocations on several architectures that do not use
PAGE_SIZE tables for one or more levels of the page table hierarchy.
Most architectures do not implement these functions and use __weak default
NOP implementation of pgd_cache_init(). Since there is no such default
for pgtable_cache_init(), its empty stub is duplicated among most
architectures.
Rename the definitions of pgd_cache_init() to pgtable_cache_init() and
drop empty stubs of pgtable_cache_init().
Link: http://lkml.kernel.org/r/1566457046-22637-1-git-send-email-rppt@linux.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Acked-by: Will Deacon <will@kernel.org> [arm64]
Acked-by: Thomas Gleixner <tglx@linutronix.de> [x86]
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "mm: remove quicklist page table caches".
A while ago Nicholas proposed to remove quicklist page table caches [1].
I've rebased his patch on the curren upstream and switched ia64 and sh to
use generic versions of PTE allocation.
[1] https://lore.kernel.org/linux-mm/20190711030339.20892-1-npiggin@gmail.com
This patch (of 3):
Remove page table allocator "quicklists". These have been around for a
long time, but have not got much traction in the last decade and are only
used on ia64 and sh architectures.
The numbers in the initial commit look interesting but probably don't
apply anymore. If anybody wants to resurrect this it's in the git
history, but it's unhelpful to have this code and divergent allocator
behaviour for minor archs.
Also it might be better to instead make more general improvements to page
allocator if this is still so slow.
Link: http://lkml.kernel.org/r/1565250728-21721-2-git-send-email-rppt@linux.ibm.com
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "Make working with compound pages easier", v2.
These three patches add three helpers and convert the appropriate
places to use them.
This patch (of 3):
It's unnecessarily hard to find out the size of a potentially huge page.
Replace 'PAGE_SIZE << compound_order(page)' with page_size(page).
Link: http://lkml.kernel.org/r/20190721104612.19120-2-willy@infradead.org
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Fix Tegra OF node reference leak (Nishka Dasgupta)
- Add #defines for PCIe Data Link Feature and Physical Layer 16.0 GT/s
features (Vidya Sagar)
- Disable MSI for Tegra Root Ports since they don't support using MSI for
all Root Port events (Vidya Sagar)
- Group DesignWare write-protected register writes together (Vidya Sagar)
- Move DesignWare capability search interfaces so they can be used by
both host and endpoint drivers (Vidya Sagar)
- Add DesignWare extended capability search interfaces (Vidya Sagar)
- Export dw_pcie_wait_for_link() so drivers can be modules (Vidya Sagar)
- Add "snps,enable-cdm-check" DT binding for Configuration Dependent
Module (CDM) register checking (Vidya Sagar)
- Add DesignWare support for "snps,enable-cdm-check" CDM checking (Vidya
Sagar)
- Add "supports-clkreq" DT binding for host drivers to decide whether to
advertise low power features (Vidya Sagar)
- Add DT binding for Tegra194 (Vidya Sagar)
- Add DT binding for Tegra194 P2U (PIPE to UPHY) block (Vidya Sagar)
- Add support for Tegra194 P2U (PIPE to UPHY) (Vidya Sagar)
- Add support for Tegra194 host controller (Vidya Sagar)
- Add Tegra support for sideband PERST# and CLKREQ# for C5 (Vidya Sagar)
- Add Tegra support for slot regulators for p2972-0000 platform (Vidya
Sagar)
* lorenzo/pci/tegra:
arm64: tegra: Add PCIe slot supply information in p2972-0000 platform
arm64: tegra: Add configuration for PCIe C5 sideband signals
PCI: tegra: Add support to enable slot regulators
PCI: tegra: Add support to configure sideband pins
dt-bindings: PCI: tegra: Add PCIe slot supplies regulator entries
dt-bindings: PCI: tegra: Add sideband pins configuration entries
PCI: tegra: Add Tegra194 PCIe support
phy: tegra: Add PCIe PIPE2UPHY support
dt-bindings: PHY: P2U: Add Tegra194 P2U block
dt-bindings: PCI: tegra: Add device tree support for Tegra194
dt-bindings: Add PCIe supports-clkreq property
PCI: dwc: Add support to enable CDM register check
dt-bindings: PCI: designware: Add binding for CDM register check
PCI: dwc: Export dw_pcie_wait_for_link() API
PCI: dwc: Add extended configuration space capability search API
PCI: dwc: Move config space capability search API
PCI: dwc: Group DBI registers writes requiring unlocking
PCI: Disable MSI for Tegra root ports
PCI: Add #defines for some of PCIe spec r4.0 features
PCI: tegra: Fix OF node reference leak
This is mostly update of the usual drivers: qla2xxx, ufs, smartpqi,
lpfc, hisi_sas, qedf, mpt3sas; plus a whole load of minor updates.
The only core change this time around is the addition of request
batching for virtio. Since batching requires an additional flag to
use, it should be invisible to the rest of the drivers.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXYQE/yYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishXs9AP4usPY5
OpMlF6OiKFNeJrCdhCScVghf9uHbc7UA6cP+EgD/bCtRgcDe1ZjOTYWdeTwvwWqA
ltWYonnv6Lg3b1f9yqI=
=jRC/
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: qla2xxx, ufs, smartpqi,
lpfc, hisi_sas, qedf, mpt3sas; plus a whole load of minor updates. The
only core change this time around is the addition of request batching
for virtio. Since batching requires an additional flag to use, it
should be invisible to the rest of the drivers"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (264 commits)
scsi: hisi_sas: Fix the conflict between device gone and host reset
scsi: hisi_sas: Add BIST support for phy loopback
scsi: hisi_sas: Add hisi_sas_debugfs_alloc() to centralise allocation
scsi: hisi_sas: Remove some unused function arguments
scsi: hisi_sas: Remove redundant work declaration
scsi: hisi_sas: Remove hisi_sas_hw.slot_complete
scsi: hisi_sas: Assign NCQ tag for all NCQ commands
scsi: hisi_sas: Update all the registers after suspend and resume
scsi: hisi_sas: Retry 3 times TMF IO for SAS disks when init device
scsi: hisi_sas: Remove sleep after issue phy reset if sas_smp_phy_control() fails
scsi: hisi_sas: Directly return when running I_T_nexus reset if phy disabled
scsi: hisi_sas: Use true/false as input parameter of sas_phy_reset()
scsi: hisi_sas: add debugfs auto-trigger for internal abort time out
scsi: virtio_scsi: unplug LUNs when events missed
scsi: scsi_dh_rdac: zero cdb in send_mode_select()
scsi: fcoe: fix null-ptr-deref Read in fc_release_transport
scsi: ufs-hisi: use devm_platform_ioremap_resource() to simplify code
scsi: ufshcd: use devm_platform_ioremap_resource() to simplify code
scsi: hisi_sas: use devm_platform_ioremap_resource() to simplify code
scsi: ufs: Use kmemdup in ufshcd_read_string_desc()
...
This is some material that we picked up into our tree late or
that had complex inter-depondencies. The fact that there are these
interdependencies tends to meant that these are often actually the most
interesting new additions:
The new Aspeed AST2600 baseboard management controller is added, this
is a Cortex-A7 based follow-up to the ARM11 based AST2500 and had some
dependencies on other device drivers.
After many years, support for the MMP2 based OLPC XO-1.75 finally makes
it into the kernel.
The Armada 3720 based Turris Mox open source router platform is a late
addition and it follows some preparatory work across multiple branches.
The OMAP2+ platform had some large-scale cleanup involving driver
changes and DT changes, here we finish it off, dropping a lot of the
now-unused platform data.
The TI K3 platform that got added for 5.3 gains a lot more support
for individual bits on the SoC, this part just came late for the
merge window.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Qtkp
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC late updates from Arnd Bergmann:
"This is some material that we picked up into our tree late or that had
complex inter-depondencies. The fact that there are these
interdependencies tends to meant that these are often actually the
most interesting new additions:
- The new Aspeed AST2600 baseboard management controller is added,
this is a Cortex-A7 based follow-up to the ARM11 based AST2500 and
had some dependencies on other device drivers.
- After many years, support for the MMP2 based OLPC XO-1.75 finally
makes it into the kernel.
- The Armada 3720 based Turris Mox open source router platform is a
late addition and it follows some preparatory work across multiple
branches.
- The OMAP2+ platform had some large-scale cleanup involving driver
changes and DT changes, here we finish it off, dropping a lot of
the now-unused platform data.
- The TI K3 platform that got added for 5.3 gains a lot more support
for individual bits on the SoC, this part just came late for the
merge window"
[ This pull request itself wasn't actually sent late at all by Arnd, but
I waited on the branches that it used to be pulled first, so it ends
up being merged much later than the other ARM SoC pull requests this
merge window - Linus ]
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (57 commits)
ARM: dts: dir685: Drop spi-cpol from the display
ARM: dts: aspeed: Add AST2600 pinmux nodes
ARM: dts: aspeed: Add AST2600 and EVB
ARM: exynos: Enable support for ARM architected timers
ARM: samsung: Fix system restart on S3C6410
ARM: dts: mmp2: add OLPC XO 1.75 machine
ARM: dts: mmp2: rename the USB PHY node
ARM: dts: mmp2: specify reg-shift for the UARTs
ARM: dts: mmp2: add camera interfaces
ARM: dts: mmp2: fix the SPI nodes
ARM: dts: mmp2: trivial whitespace fix
arm64: dts: marvell: add DTS for Turris Mox
dt-bindings: marvell: document Turris Mox compatible
arm64: dts: marvell: armada-37xx: add SPI CS1 pinctrl
arm64: dts: ti: k3-j721e-main: Fix gic-its node unit-address
arm64: dts: ti: k3-am65-main: Fix gic-its node unit-address
arm64: dts: ti: k3-j721e-main: Add hwspinlock node
arm64: dts: ti: k3-am65-main: Add hwspinlock node
arm64: dts: k3-j721e: Add gpio-keys on common processor board
dt-bindings: pinctrl: k3: Introduce pinmux definitions for J721E
...
Add 3.3V and 12V supplies regulators information of x16 PCIe slot in
p2972-0000 platform which is owned by C5 controller and also enable C5
controller.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Add support to configure PCIe C5's sideband signals PERST# and CLKREQ#
as output and bi-directional signals respectively which unlike other
PCIe controllers sideband signals are not configured by default.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
- Fix clang build breakage with CONFIG_OPTIMIZE_INLINING=y
- Fix compilation of pointer tagging selftest
- Fix COND_SYSCALL definitions to work with CFI checks
- Fix stale documentation reference in our Kconfig
-----BEGIN PGP SIGNATURE-----
iQFEBAABCgAuFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAl2DO5cQHHdpbGxAa2Vy
bmVsLm9yZwAKCRC3rHDchMFjNBHhCADEoSOk8WSijBvC4WNCPXBvukuk2KEwal2s
By+iEo3byr9uRskduddumEnTA3F5otfV7VR3HG34P8K3dzP541Zw8sPs5Q1MU/Zo
7SzU6J14q+Q3V/+F0RDpajP60bBbmjYQi23xmO8hnnHbZlIV7dteD+JvMWrNh31M
nTvPHpS+jm/SNFUSL1EMnbr2Au5UhN8j+9Qk1NyPgmTV9DkS4drDs4lBqp8VhvCD
v6kC3vdW5DiXvMHoa5RXO+3B57HYVmlhylEO0ZOmKxyZEhph1jiuR2ng4CDYtxo3
qngynXxa7u79a6TdDhnzresaku4xM22UO9bf1WkVq9yv6JQ7/ArV
=wZPH
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"We've had a few arm64 fixes trickle in this week. Nothing catastophic,
but all things that should be addressed:
- Fix clang build breakage with CONFIG_OPTIMIZE_INLINING=y
- Fix compilation of pointer tagging selftest
- Fix COND_SYSCALL definitions to work with CFI checks
- Fix stale documentation reference in our Kconfig"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Fix reference to docs for ARM64_TAGGED_ADDR_ABI
arm64: fix function types in COND_SYSCALL
selftests, arm64: add kernel headers path for tags_test
arm64: fix unreachable code issue with cmpxchg
- Addition of multiprobes to kprobe and uprobe events
Allows for more than one probe attached to the same location
- Addition of adding immediates to probe parameters
- Clean up of the recordmcount.c code. This brings us closer
to merging recordmcount into objtool, and reuse code.
- Other small clean ups
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCXYQoqhQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qlIxAP9VVABbpuvOYqxKuFgyP62ituSXPLkL
gZv4I5Zse4b6/gD/eksFXY/OHo7jp6aQiHvxotUkAiFFE9iHzi0JscdMJgo=
=WqrT
-----END PGP SIGNATURE-----
Merge tag 'trace-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
- Addition of multiprobes to kprobe and uprobe events (allows for more
than one probe attached to the same location)
- Addition of adding immediates to probe parameters
- Clean up of the recordmcount.c code. This brings us closer to merging
recordmcount into objtool, and reuse code.
- Other small clean ups
* tag 'trace-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (33 commits)
selftests/ftrace: Update kprobe event error testcase
tracing/probe: Reject exactly same probe event
tracing/probe: Fix to allow user to enable events on unloaded modules
selftests/ftrace: Select an existing function in kprobe_eventname test
tracing/kprobe: Fix NULL pointer access in trace_porbe_unlink()
tracing: Make sure variable reference alias has correct var_ref_idx
tracing: Be more clever when dumping hex in __print_hex()
ftrace: Simplify ftrace hash lookup code in clear_func_from_hash()
tracing: Add "gfp_t" support in synthetic_events
tracing: Rename tracing_reset() to tracing_reset_cpu()
tracing: Document the stack trace algorithm in the comments
tracing/arm64: Have max stack tracer handle the case of return address after data
recordmcount: Clarify what cleanup() does
recordmcount: Remove redundant cleanup() calls
recordmcount: Kernel style formatting
recordmcount: Kernel style function signature formatting
recordmcount: Rewrite error/success handling
selftests/ftrace: Add syntax error test for multiprobe
selftests/ftrace: Add syntax error test for immediates
selftests/ftrace: Add a testcase for kprobe multiprobe event
...
- add modpost warn exported symbols marked as 'static' because 'static'
and EXPORT_SYMBOL is an odd combination
- break the build early if gold linker is used
- optimize the Bison rule to produce .c and .h files by a single
pattern rule
- handle PREEMPT_RT in the module vermagic and UTS_VERSION
- warn CONFIG options leaked to the user-space except existing ones
- make single targets work properly
- rebuild modules when module linker scripts are updated
- split the module final link stage into scripts/Makefile.modfinal
- fix the missed error code in merge_config.sh
- improve the error message displayed on the attempt of the O= build
in unclean source tree
- remove 'clean-dirs' syntax
- disable -Wimplicit-fallthrough warning for Clang
- add CONFIG_CC_OPTIMIZE_FOR_SIZE_O3 for ARC
- remove ARCH_{CPP,A,C}FLAGS variables
- add $(BASH) to run bash scripts
- change *CFLAGS_<basetarget>.o to take the relative path to $(obj)
instead of the basename
- stop suppressing Clang's -Wunused-function warnings when W=1
- fix linux/export.h to avoid genksyms calculating CRC of trimmed
exported symbols
- misc cleanups
-----BEGIN PGP SIGNATURE-----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=VGqV
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- add modpost warn exported symbols marked as 'static' because 'static'
and EXPORT_SYMBOL is an odd combination
- break the build early if gold linker is used
- optimize the Bison rule to produce .c and .h files by a single
pattern rule
- handle PREEMPT_RT in the module vermagic and UTS_VERSION
- warn CONFIG options leaked to the user-space except existing ones
- make single targets work properly
- rebuild modules when module linker scripts are updated
- split the module final link stage into scripts/Makefile.modfinal
- fix the missed error code in merge_config.sh
- improve the error message displayed on the attempt of the O= build in
unclean source tree
- remove 'clean-dirs' syntax
- disable -Wimplicit-fallthrough warning for Clang
- add CONFIG_CC_OPTIMIZE_FOR_SIZE_O3 for ARC
- remove ARCH_{CPP,A,C}FLAGS variables
- add $(BASH) to run bash scripts
- change *CFLAGS_<basetarget>.o to take the relative path to $(obj)
instead of the basename
- stop suppressing Clang's -Wunused-function warnings when W=1
- fix linux/export.h to avoid genksyms calculating CRC of trimmed
exported symbols
- misc cleanups
* tag 'kbuild-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (63 commits)
genksyms: convert to SPDX License Identifier for lex.l and parse.y
modpost: use __section in the output to *.mod.c
modpost: use MODULE_INFO() for __module_depends
export.h, genksyms: do not make genksyms calculate CRC of trimmed symbols
export.h: remove defined(__KERNEL__), which is no longer needed
kbuild: allow Clang to find unused static inline functions for W=1 build
kbuild: rename KBUILD_ENABLE_EXTRA_GCC_CHECKS to KBUILD_EXTRA_WARN
kbuild: refactor scripts/Makefile.extrawarn
merge_config.sh: ignore unwanted grep errors
kbuild: change *FLAGS_<basetarget>.o to take the path relative to $(obj)
modpost: add NOFAIL to strndup
modpost: add guid_t type definition
kbuild: add $(BASH) to run scripts with bash-extension
kbuild: remove ARCH_{CPP,A,C}FLAGS
kbuild,arc: add CONFIG_CC_OPTIMIZE_FOR_PERFORMANCE_O3 for ARC
kbuild: Do not enable -Wimplicit-fallthrough for clang for now
kbuild: clean up subdir-ymn calculation in Makefile.clean
kbuild: remove unneeded '+' marker from cmd_clean
kbuild: remove clean-dirs syntax
kbuild: check clean srctree even earlier
...
- add dma-mapping and block layer helpers to take care of IOMMU
merging for mmc plus subsequent fixups (Yoshihiro Shimoda)
- rework handling of the pgprot bits for remapping (me)
- take care of the dma direct infrastructure for swiotlb-xen (me)
- improve the dma noncoherent remapping infrastructure (me)
- better defaults for ->mmap, ->get_sgtable and ->get_required_mask (me)
- cleanup mmaping of coherent DMA allocations (me)
- various misc cleanups (Andy Shevchenko, me)
-----BEGIN PGP SIGNATURE-----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=/wGv
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-5.4' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- add dma-mapping and block layer helpers to take care of IOMMU merging
for mmc plus subsequent fixups (Yoshihiro Shimoda)
- rework handling of the pgprot bits for remapping (me)
- take care of the dma direct infrastructure for swiotlb-xen (me)
- improve the dma noncoherent remapping infrastructure (me)
- better defaults for ->mmap, ->get_sgtable and ->get_required_mask
(me)
- cleanup mmaping of coherent DMA allocations (me)
- various misc cleanups (Andy Shevchenko, me)
* tag 'dma-mapping-5.4' of git://git.infradead.org/users/hch/dma-mapping: (41 commits)
mmc: renesas_sdhi_internal_dmac: Add MMC_CAP2_MERGE_CAPABLE
mmc: queue: Fix bigger segments usage
arm64: use asm-generic/dma-mapping.h
swiotlb-xen: merge xen_unmap_single into xen_swiotlb_unmap_page
swiotlb-xen: simplify cache maintainance
swiotlb-xen: use the same foreign page check everywhere
swiotlb-xen: remove xen_swiotlb_dma_mmap and xen_swiotlb_dma_get_sgtable
xen: remove the exports for xen_{create,destroy}_contiguous_region
xen/arm: remove xen_dma_ops
xen/arm: simplify dma_cache_maint
xen/arm: use dev_is_dma_coherent
xen/arm: consolidate page-coherent.h
xen/arm: use dma-noncoherent.h calls for xen-swiotlb cache maintainance
arm: remove wrappers for the generic dma remap helpers
dma-mapping: introduce a dma_common_find_pages helper
dma-mapping: always use VM_DMA_COHERENT for generic DMA remap
vmalloc: lift the arm flag for coherent mappings to common code
dma-mapping: provide a better default ->get_required_mask
dma-mapping: remove the dma_declare_coherent_memory export
remoteproc: don't allow modular build
...
Pull networking updates from David Miller:
1) Support IPV6 RA Captive Portal Identifier, from Maciej Żenczykowski.
2) Use bio_vec in the networking instead of custom skb_frag_t, from
Matthew Wilcox.
3) Make use of xmit_more in r8169 driver, from Heiner Kallweit.
4) Add devmap_hash to xdp, from Toke Høiland-Jørgensen.
5) Support all variants of 5750X bnxt_en chips, from Michael Chan.
6) More RTNL avoidance work in the core and mlx5 driver, from Vlad
Buslov.
7) Add TCP syn cookies bpf helper, from Petar Penkov.
8) Add 'nettest' to selftests and use it, from David Ahern.
9) Add extack support to drop_monitor, add packet alert mode and
support for HW drops, from Ido Schimmel.
10) Add VLAN offload to stmmac, from Jose Abreu.
11) Lots of devm_platform_ioremap_resource() conversions, from
YueHaibing.
12) Add IONIC driver, from Shannon Nelson.
13) Several kTLS cleanups, from Jakub Kicinski.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1930 commits)
mlxsw: spectrum_buffers: Add the ability to query the CPU port's shared buffer
mlxsw: spectrum: Register CPU port with devlink
mlxsw: spectrum_buffers: Prevent changing CPU port's configuration
net: ena: fix incorrect update of intr_delay_resolution
net: ena: fix retrieval of nonadaptive interrupt moderation intervals
net: ena: fix update of interrupt moderation register
net: ena: remove all old adaptive rx interrupt moderation code from ena_com
net: ena: remove ena_restore_ethtool_params() and relevant fields
net: ena: remove old adaptive interrupt moderation code from ena_netdev
net: ena: remove code duplication in ena_com_update_nonadaptive_moderation_interval _*()
net: ena: enable the interrupt_moderation in driver_supported_features
net: ena: reimplement set/get_coalesce()
net: ena: switch to dim algorithm for rx adaptive interrupt moderation
net: ena: add intr_moder_rx_interval to struct ena_com_dev and use it
net: phy: adin: implement Energy Detect Powerdown mode via phy-tunable
ethtool: implement Energy Detect Powerdown support via phy-tunable
xen-netfront: do not assume sk_buff_head list is empty in error handling
s390/ctcm: Delete unnecessary checks before the macro call “dev_kfree_skb”
net: ena: don't wake up tx queue when down
drop_monitor: Better sanitize notified packets
...
Pull crypto updates from Herbert Xu:
"API:
- Add the ability to abort a skcipher walk.
Algorithms:
- Fix XTS to actually do the stealing.
- Add library helpers for AES and DES for single-block users.
- Add library helpers for SHA256.
- Add new DES key verification helper.
- Add surrounding bits for ESSIV generator.
- Add accelerations for aegis128.
- Add test vectors for lzo-rle.
Drivers:
- Add i.MX8MQ support to caam.
- Add gcm/ccm/cfb/ofb aes support in inside-secure.
- Add ofb/cfb aes support in media-tek.
- Add HiSilicon ZIP accelerator support.
Others:
- Fix potential race condition in padata.
- Use unbound workqueues in padata"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (311 commits)
crypto: caam - Cast to long first before pointer conversion
crypto: ccree - enable CTS support in AES-XTS
crypto: inside-secure - Probe transform record cache RAM sizes
crypto: inside-secure - Base RD fetchcount on actual RD FIFO size
crypto: inside-secure - Base CD fetchcount on actual CD FIFO size
crypto: inside-secure - Enable extended algorithms on newer HW
crypto: inside-secure: Corrected configuration of EIP96_TOKEN_CTRL
crypto: inside-secure - Add EIP97/EIP197 and endianness detection
padata: remove cpu_index from the parallel_queue
padata: unbind parallel jobs from specific CPUs
padata: use separate workqueues for parallel and serial work
padata, pcrypt: take CPU hotplug lock internally in padata_alloc_possible
crypto: pcrypt - remove padata cpumask notifier
padata: make padata_do_parallel find alternate callback CPU
workqueue: require CPU hotplug read exclusion for apply_workqueue_attrs
workqueue: unconfine alloc/apply/free_workqueue_attrs()
padata: allocate workqueue internally
arm64: dts: imx8mq: Add CAAM node
random: Use wait_event_freezable() in add_hwgenerator_randomness()
crypto: ux500 - Fix COMPILE_TEST warnings
...
* ARM: ITS translation cache; support for 512 vCPUs, various cleanups
and bugfixes
* PPC: various minor fixes and preparation
* x86: bugfixes all over the place (posted interrupts, SVM, emulation
corner cases, blocked INIT), some IPI optimizations
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJdf7fdAAoJEL/70l94x66DJzkIAKDcuWXJB4Qtoto6yUvPiHZm
LYkY/Dn1zulb/DhzrBoXFey/jZXwl9kxMYkVTefnrAl0fRwFGX+G1UYnQrtAL6Gr
ifdTYdy3kZhXCnnp99QAantWDswJHo1THwbmHrlmkxS4MdisEaTHwgjaHrDRZ4/d
FAEwW2isSonP3YJfTtsKFFjL9k2D4iMnwZ/R2B7UOaWvgnerZ1GLmOkilvnzGGEV
IQ89IIkWlkKd4SKgq8RkDKlfW5JrLrSdTK2Uf0DvAxV+J0EFkEaR+WlLsqumra0z
Eg3KwNScfQj0DyT0TzurcOxObcQPoMNSFYXLRbUu1+i0CGgm90XpF1IosiuihgU=
=w6I3
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"s390:
- ioctl hardening
- selftests
ARM:
- ITS translation cache
- support for 512 vCPUs
- various cleanups and bugfixes
PPC:
- various minor fixes and preparation
x86:
- bugfixes all over the place (posted interrupts, SVM, emulation
corner cases, blocked INIT)
- some IPI optimizations"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (75 commits)
KVM: X86: Use IPI shorthands in kvm guest when support
KVM: x86: Fix INIT signal handling in various CPU states
KVM: VMX: Introduce exit reason for receiving INIT signal on guest-mode
KVM: VMX: Stop the preemption timer during vCPU reset
KVM: LAPIC: Micro optimize IPI latency
kvm: Nested KVM MMUs need PAE root too
KVM: x86: set ctxt->have_exception in x86_decode_insn()
KVM: x86: always stop emulation on page fault
KVM: nVMX: trace nested VM-Enter failures detected by H/W
KVM: nVMX: add tracepoint for failed nested VM-Enter
x86: KVM: svm: Fix a check in nested_svm_vmrun()
KVM: x86: Return to userspace with internal error on unexpected exit reason
KVM: x86: Add kvm_emulate_{rd,wr}msr() to consolidate VXM/SVM code
KVM: x86: Refactor up kvm_{g,s}et_msr() to simplify callers
doc: kvm: Fix return description of KVM_SET_MSRS
KVM: X86: Tune PLE Window tracepoint
KVM: VMX: Change ple_window type to unsigned int
KVM: X86: Remove tailing newline for tracepoints
KVM: X86: Trace vcpu_id for vmexit
KVM: x86: Manually calculate reserved bits when loading PDPTRS
...
The referenced file does not exist, but tagged-address-abi.rst does.
Signed-off-by: Jeremy Cline <jcline@redhat.com>
Signed-off-by: Will Deacon <will@kernel.org>
Pull core timer updates from Thomas Gleixner:
"Timers and timekeeping updates:
- A large overhaul of the posix CPU timer code which is a preparation
for moving the CPU timer expiry out into task work so it can be
properly accounted on the task/process.
An update to the bogus permission checks will come later during the
merge window as feedback was not complete before heading of for
travel.
- Switch the timerqueue code to use cached rbtrees and get rid of the
homebrewn caching of the leftmost node.
- Consolidate hrtimer_init() + hrtimer_init_sleeper() calls into a
single function
- Implement the separation of hrtimers to be forced to expire in hard
interrupt context even when PREEMPT_RT is enabled and mark the
affected timers accordingly.
- Implement a mechanism for hrtimers and the timer wheel to protect
RT against priority inversion and live lock issues when a (hr)timer
which should be canceled is currently executing the callback.
Instead of infinitely spinning, the task which tries to cancel the
timer blocks on a per cpu base expiry lock which is held and
released by the (hr)timer expiry code.
- Enable the Hyper-V TSC page based sched_clock for Hyper-V guests
resulting in faster access to timekeeping functions.
- Updates to various clocksource/clockevent drivers and their device
tree bindings.
- The usual small improvements all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (101 commits)
posix-cpu-timers: Fix permission check regression
posix-cpu-timers: Always clear head pointer on dequeue
hrtimer: Add a missing bracket and hide `migration_base' on !SMP
posix-cpu-timers: Make expiry_active check actually work correctly
posix-timers: Unbreak CONFIG_POSIX_TIMERS=n build
tick: Mark sched_timer to expire in hard interrupt context
hrtimer: Add kernel doc annotation for HRTIMER_MODE_HARD
x86/hyperv: Hide pv_ops access for CONFIG_PARAVIRT=n
posix-cpu-timers: Utilize timerqueue for storage
posix-cpu-timers: Move state tracking to struct posix_cputimers
posix-cpu-timers: Deduplicate rlimit handling
posix-cpu-timers: Remove pointless comparisons
posix-cpu-timers: Get rid of 64bit divisions
posix-cpu-timers: Consolidate timer expiry further
posix-cpu-timers: Get rid of zero checks
rlimit: Rewrite non-sensical RLIMIT_CPU comment
posix-cpu-timers: Respect INFINITY for hard RTTIME limit
posix-cpu-timers: Switch thread group sampling to array
posix-cpu-timers: Restructure expiry array
posix-cpu-timers: Remove cputime_expires
...
Define a weak function in COND_SYSCALL instead of a weak alias to
sys_ni_syscall, which has an incompatible type. This fixes indirect
call mismatches with Control-Flow Integrity (CFI) checking.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Will Deacon <will@kernel.org>
On arm64 build with clang, sometimes the __cmpxchg_mb is not inlined
when CONFIG_OPTIMIZE_INLINING is set.
Clang then fails a compile-time assertion, because it cannot tell at
compile time what the size of the argument is:
mm/memcontrol.o: In function `__cmpxchg_mb':
memcontrol.c:(.text+0x1a4c): undefined reference to `__compiletime_assert_175'
memcontrol.c:(.text+0x1a4c): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `__compiletime_assert_175'
Mark all of the cmpxchg() style functions as __always_inline to
ensure that the compiler can see the result.
Acked-by: Nick Desaulniers <ndesaulniers@google.com>
Reported-by: Nathan Chancellor <natechancellor@gmail.com>
Link: https://github.com/ClangBuiltLinux/linux/issues/648
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Tested-by: Andrew Murray <andrew.murray@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Will Deacon <will@kernel.org>
This is another huge branch with close to 450 changessets related to
devicetree files, roughly half of this for 32-bit and 64-bit respectively.
There are lots of cleanups and additional hardware support for platforms
we already support based on SoCs from Renesas, ST-Microelectronics,
Intel/Altera, Rockchips, Allwinner, Broadcom and other manufacturers.
A total of 6 new SoCs and 37 new boards gets added this time, one more
SoC will come in a follow-up branch. Most of the new boards are for
64-bit ARM SoCs, the others are typically for the 32-bit Cortex-A7.
Going more into details for SoC platforms with new hardware support:
The Snapdragon 855 (SM8150) is Qualcomm's current high-end phone platform,
usually paired with an external 5G modem. So far we only support the
Qualcomm SM8150 MTP reference platform, but no actual products.
For the slightly older Qualcomm platforms, support for several interesting
products is getting added: Three laptops based on Snapdragon 835/MSM8998
(Asus NovaGo, HP Envy X2 and Lenovo Miix 630), one laptop based on
Snapdragon 850/sdm850 (Lenovo Yoga C630) and several phones based on
the older Snapdragon 410/MSM8916 (Samsung A3 and A5, Longcheer L8150
aka Android One 2nd gen "seed" aka Wileyfox Swift).
Mediatek MT7629 is a new wireless network router chip, similar to
the older MT7623. It gets added together with the reference board
implementation.
Allwinner V3 is a repackaged version of the existing low-end V3s chip,
and is used in the tiny Lichee Pi Zero plus, also added here. There is
also a new TV set-top box based on Allwinner H6, the Tanix TX6, and the
eMMC variant of the Olimex A64-Olinuxino development board.
NXP i.MX8M Nano is a new member of the ever-expanding i.MX SoC family,
similar to the i.MX8M Mini. As usual, there is a large number of new
boards for i.MX SoCs: Einfochips i.MX8QXP AI_ML, SolidRun Hummingboard
Pulse baseboard and System-on-Module, Boundary Devices i.MX8MQ Nitrogen8M,
and TechNexion PICO-PI-IMX8M-DEV for the 64-bit i.MX8 line. For 32-bit,
we get the Kontron i.MX6UL N6310 SoM with two baseboards, the PHYTEC
phyBOARD-Segin SoM with three baseboards, and the Zodiac Inflight
Innovations i.MX7 RMU2 board.
In a different NXP product line, the Layerscape LS1046A "Freeway"
reference board gets added.
Amlogic SM1 (S905X3) and G12B (S922X, A311D) are updated chips from their
set-top-box line and smart speaker with newer CPU and GPU cores compared
to their predecessors. Both are now also supported by the Khadas VIM3
development board series, and the dts files for that get reorganized a
bit to better deal with all variants. Another board based on SM1 that
gets added is the SEI Robotics SEI610.
There are a handful of new x86 and Power9 server boards using Aspeed BMC
chips that are gaining support for running Linux on the BMC through the
OpenBMC project: Facebook Minipack/Wedge100/Wedge40, Lenovo Hr855xg2,
and Mihawk. Notably these are still new machines using SoCs based on
the ARM9 and ARM11 CPU cores, as support for the new Cortex-A7 based
AST2600 is still ramping up.
There are three new end-user products using 32-bit Rockchips SoCs:
Mecer Xtreme Mini S6 is an Android "mini PC" box based on the low-end
RK3229 chip, while the two AOpen products Chromebox Mini (Fievel) and
Chromebase Mini (Tiger) run ChromeOS and are meant for commercial settings
(digital signage, PoS, ...).
One more single-board computer based on the popular 64-bit RK3399 is
added: the Leez RK3399 P710.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJdf6StAAoJEJpsee/mABjZDfEP/3h0GusRkoQ6PJ5FHsj4nIR6
NJK8RxmX4B4ctXxBc+Rbt8bHp1d/IdHL4Jcqe7xgR2OIVQPloJz1lFrLaF0wn4Mu
G1EP2DzcLym3K0lBwhByvXfU1s2lhaTYdT594J8kTEVgcPXe79LKqH42A1T+1IlC
7+xAh9sU++NLo64w+Iam3d3T72ugyeO7THWiie7Rb9wACS94i7cZwvasur35aHxf
Ut5nOQYPbTuVVvN1FfZAdrHJpK9r7pbJLVwHLMdHnUYup2XDmoC6iuDrKlsWxqjs
SBL0u+dO5pkdKQp17RZFQZwrx2Y97E9KLWaT9Cqb7nwJ+ftYf419TUioQvmyJRZd
DEsCz6GVCCOs2zFcGj+9iGRr5wA2O3I42dOZkkkTciztksFwSmomrSlwAgVBT2ms
In6K3g2DrN31aDGFW9dZnxBXHVHWXkqr/TN4UIO2h0jfR4bazAvPzBiDpJdkz1NY
KPpDrdTRA2k4UnSimot/7Pw8y2NtsTDVJeQS1KydSe44PiLLumO8hg+FfnhJoW5s
oaSjX89549JvUIrA7TbXPxpyGS8oo7a1XkQyzfWZs8l7JMWoR5oK/VdiuDBL7YDE
XFlcZmCmB+kUgtSgXjw9FflkoMn06usVZBo1rnWFApYmzZ3htnniNSgz/zjMJpXn
OtQTQnP2LzS+ioxqB2Se
=Bm5T
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM DT updates from Arnd Bergmann:
"This is another huge branch with close to 450 changessets related to
devicetree files, roughly half of this for 32-bit and 64-bit
respectively. There are lots of cleanups and additional hardware
support for platforms we already support based on SoCs from Renesas,
ST-Microelectronics, Intel/Altera, Rockchips, Allwinner, Broadcom and
other manufacturers.
A total of 6 new SoCs and 37 new boards gets added this time, one more
SoC will come in a follow-up branch. Most of the new boards are for
64-bit ARM SoCs, the others are typically for the 32-bit Cortex-A7.
Going more into details for SoC platforms with new hardware support:
- The Snapdragon 855 (SM8150) is Qualcomm's current high-end phone
platform, usually paired with an external 5G modem. So far we only
support the Qualcomm SM8150 MTP reference platform, but no actual
products.
- For the slightly older Qualcomm platforms, support for several
interesting products is getting added: Three laptops based on
Snapdragon 835/MSM8998 (Asus NovaGo, HP Envy X2 and Lenovo Miix
630), one laptop based on Snapdragon 850/sdm850 (Lenovo Yoga C630)
and several phones based on the older Snapdragon 410/MSM8916
(Samsung A3 and A5, Longcheer L8150 aka Android One 2nd gen "seed"
aka Wileyfox Swift).
- Mediatek MT7629 is a new wireless network router chip, similar to
the older MT7623. It gets added together with the reference board
implementation.
- Allwinner V3 is a repackaged version of the existing low-end V3s
chip, and is used in the tiny Lichee Pi Zero plus, also added here.
There is also a new TV set-top box based on Allwinner H6, the Tanix
TX6, and the eMMC variant of the Olimex A64-Olinuxino development
board.
- NXP i.MX8M Nano is a new member of the ever-expanding i.MX SoC
family, similar to the i.MX8M Mini. As usual, there is a large
number of new boards for i.MX SoCs: Einfochips i.MX8QXP AI_ML,
SolidRun Hummingboard Pulse baseboard and System-on-Module,
Boundary Devices i.MX8MQ Nitrogen8M, and TechNexion
PICO-PI-IMX8M-DEV for the 64-bit i.MX8 line. For 32-bit, we get the
Kontron i.MX6UL N6310 SoM with two baseboards, the PHYTEC
phyBOARD-Segin SoM with three baseboards, and the Zodiac Inflight
Innovations i.MX7 RMU2 board.
- In a different NXP product line, the Layerscape LS1046A "Freeway"
reference board gets added.
- Amlogic SM1 (S905X3) and G12B (S922X, A311D) are updated chips from
their set-top-box line and smart speaker with newer CPU and GPU
cores compared to their predecessors. Both are now also supported
by the Khadas VIM3 development board series, and the dts files for
that get reorganized a bit to better deal with all variants.
Another board based on SM1 that gets added is the SEI Robotics
SEI610.
- There are a handful of new x86 and Power9 server boards using
Aspeed BMC chips that are gaining support for running Linux on the
BMC through the OpenBMC project: Facebook
Minipack/Wedge100/Wedge40, Lenovo Hr855xg2, and Mihawk. Notably
these are still new machines using SoCs based on the ARM9 and ARM11
CPU cores, as support for the new Cortex-A7 based AST2600 is still
ramping up.
- There are three new end-user products using 32-bit Rockchips SoCs:
Mecer Xtreme Mini S6 is an Android "mini PC" box based on the
low-end RK3229 chip, while the two AOpen products Chromebox Mini
(Fievel) and Chromebase Mini (Tiger) run ChromeOS and are meant for
commercial settings(digital signage, PoS, ...).
- One more single-board computer based on the popular 64-bit RK3399
is added: the Leez RK3399 P710"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (467 commits)
arm64: dts: qcom: Add Lenovo Yoga C630
ARM: dts: aspeed-g5: Fixe gpio-ranges upper limit
ARM; dts: aspeed: mihawk: File should not be executable
ARM: dts: aspeed: swift: Change power supplies to version 2
ARM: dts: aspeed: vesnin: Add secondary SPI flash chip
ARM: dts: aspeed: vesnin: Add wdt2 with alt-boot option
ARM: dts: aspeed-g4: Add all flash chips
ARM: dts: exynos: Enable GPU/Mali T604 on Arndale board
ARM: dts: exynos: Enable GPU/Mali T604 on Chromebook Snow
ARM: dts: exynos: Add GPU/Mali T604 node to Exynos5250
ARM: dts: exynos: Fix min/max buck4 for GPU on Arndale board
ARM: dts: exynos: Mark LDO10 as always-on on Peach Pit/Pi Chromebooks
ARM: dts: exynos: Remove not accurate secondary ADC compatible
arm64: dts: rockchip: limit clock rate of MMC controllers for RK3328
arm64: dts: meson-sm1-sei610: add stdout-path property back
arm64: dts: meson-sm1-sei610: enable DVFS
arm64: dts: khadas-vim3: add support for the SM1 based VIM3L
dt-bindings: arm: amlogic: add Amlogic SM1 based Khadas VIM3L bindings
arm64: dts: khadas-vim3: move common nodes into meson-khadas-vim3.dtsi
arm64: dts: meson: g12a: add reset to tdm formatters
...
As usual, a bunch of commits, mostly adding drivers and other
options to defconfigs after the code was merged through another
tree.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=S1hW
-----END PGP SIGNATURE-----
Merge tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC defconfig updates from Arnd Bergmann:
"As usual, a bunch of commits, mostly adding drivers and other options
to defconfigs after the code was merged through another tree"
* tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (32 commits)
arm64: defconfig: Enable Qualcomm QUSB2 PHY
arm64: defconfig: Enable the EFI Framebuffer
arm64: defconfig: Enable Qualcomm GENI based I2C controller
ARM: multi_v7_defconfig: Make MAX77802 regulator driver built-in
arm64: defconfig: Enable CPU clock drivers for Qualcomm msm8916
arm64: defconfig: Add DRM_MSM to defconfigs with ARCH_QCOM
ARM: multi_v7_defconfig: Add DRM_MSM to defconfigs with ARCH_QCOM
ARM: qcom_defconfig: Add DRM_MSM to defconfigs with ARCH_QCOM
ARM: configs: aspeed_g5: Enable AST2600
ARM: configs: multi_v7: Add ASPEED G6
arm64: defconfig: Enable SM8150 GCC and pinctrl driver
arm64: defconfig: Enable CONFIG_ACPI_APEI_PCIEAER
arm64: defconfig: Enable the DesignWare watchdog
ARM: multi_v7_defconfig: Enable SPI_STM32_QSPI support
ARM: imx_v6_v7_defconfig: Enable the PSCI CPUidle driver
arm64: defconfig: Enable the PSCI CPUidle driver
arm64: defconfig: Enable Sun4i SPDIF module
ARM: exynos_defconfig: Enable AHCI-platform SATA driver
arm64: defconfig: CONFIG_DRM_ETNAVIV=m
ARM: imx_v6_v7_defconfig: Select the OV5645 camera driver
...
The main change this time around is a cleanup of some of the oldest
platforms based on the XScale and ARM9 CPU cores, which are between 10
and 20 years old.
The Kendin/Micrel/Microchip KS8695, Winbond/Nuvoton W90x900 and Intel
IOP33x/IOP13xx platforms are removed after we determined that nobody is
using them any more.
The TI Davinci and NXP LPC32xx platforms on the other hand are still in
active use and are converted to the ARCH_MULTIPLATFORM build, meaning
that we can compile a kernel that works on these along with most other
ARMv5 platforms. Changes toward that goal are also merged for IOP32x,
but additional work is needed to complete this. Patches for the
remaining ARMv5 platforms have started but need more work and some
testing.
Support for the new ASpeed AST2600 gets added, this is based on the
Cortex-A7 ARMv7 core, and is a newer version of the existing ARMv5 and
ARMv6 chips in the same family.
Other changes include a cleanup of the ST-Ericsson ux500 platform
and the move of the TI Davinci platform to a new clocksource driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJdf6RZAAoJEJpsee/mABjZDO0QAKGkhoEdUmrar0Yf7/ibTrLK
0naWvQtPEm6dv+u1zNfe2IWchVRbBVm+YSLbyaAZwJQknV5gdxgd/UyQrSG9yywg
xDEUdnj03AksYreWbr1tfcA6kQQJEeqZeysNej0v7MAd6MFz5O4M4CgYfAnCLCc4
5rzSqbtFgv4uNMnMTJGKk8anFWNYLbewoBGVcGIEQ/KQlf1+NrlqBWk7CgvencaF
VLqpK0mllhKxAOJHGz6Q/XXiJnj0u56X9GvfcJoaxDWVrAnC6ii29NOHKeXhxS5W
/EmhIEuqCRoGLAMYmml+NbCv43Z1L7neDJwg6sf9cVqNrB9L1Ldlgpr/uoj++Z+l
wdZ297Ogs4mKYx5CCdK4X1TaFOH3s+/awFr1uEP70p+QsPDMrCTuLSjgeQziylgO
kBGIGkqG4l48V9psQy/9SaalgGSB8w6Ta/ms1+rWc99Qj3ExDFCAMIl4uzOxjxT1
9MZbvhc3ulLT4BBXNGhvNaPJxYGk+ggV/ObsqF9+GkxLcVPR8L1tPIzZMB5dB1YR
0YcwyK2jlZGKIwMjLYDT+axGGPh9G+LV6INjRbW5BGJHgNZF844Bxw/eFYushLAu
KHrbpm3ImzJw9eHlgIRtFRTy8ZKPuvv7fGg3zzKSHT4ZmC3tEM68PnQGuMEvVX8Q
+Oa6OiDb0pkV1zsACSZn
=u+ew
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Arnd Bergmann:
"The main change this time around is a cleanup of some of the oldest
platforms based on the XScale and ARM9 CPU cores, which are between 10
and 20 years old.
The Kendin/Micrel/Microchip KS8695, Winbond/Nuvoton W90x900 and Intel
IOP33x/IOP13xx platforms are removed after we determined that nobody
is using them any more.
The TI Davinci and NXP LPC32xx platforms on the other hand are still
in active use and are converted to the ARCH_MULTIPLATFORM build,
meaning that we can compile a kernel that works on these along with
most other ARMv5 platforms. Changes toward that goal are also merged
for IOP32x, but additional work is needed to complete this. Patches
for the remaining ARMv5 platforms have started but need more work and
some testing.
Support for the new ASpeed AST2600 gets added, this is based on the
Cortex-A7 ARMv7 core, and is a newer version of the existing ARMv5 and
ARMv6 chips in the same family.
Other changes include a cleanup of the ST-Ericsson ux500 platform and
the move of the TI Davinci platform to a new clocksource driver"
[ The changes had marked INTEL_IOP_ADMA and USB_LPC32XX as being
buildable on other platforms through COMPILE_TEST, but that causes new
warnings that I most definitely do not want to see during the merge
window as that could hide other issues.
So the COMPILE_TEST option got disabled for them again - Linus ]
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (61 commits)
ARM: multi_v5_defconfig: make DaVinci part of the ARM v5 multiplatform build
ARM: davinci: support multiplatform build for ARM v5
arm64: exynos: Enable exynos-chipid driver
ARM: OMAP2+: Delete an unnecessary kfree() call in omap_hsmmc_pdata_init()
ARM: OMAP2+: move platform-specific asm-offset.h to arch/arm/mach-omap2
ARM: davinci: dm646x: Fix a typo in the comment
ARM: davinci: dm646x: switch to using the clocksource driver
ARM: davinci: dm644x: switch to using the clocksource driver
ARM: aspeed: Enable SMP boot
ARM: aspeed: Add ASPEED AST2600 architecture
ARM: aspeed: Select timer in each SoC
dt-bindings: arm: cpus: Add ASPEED SMP
ARM: imx: stop adjusting ar8031 phy tx delay
mailmap: map old company name to new one @microchip.com
MAINTAINERS: at91: remove the TC entry
MAINTAINERS: at91: Collect all pinctrl/gpio drivers in same entry
ARM: at91: move platform-specific asm-offset.h to arch/arm/mach-at91
MAINTAINERS: Extend patterns for Samsung SoC, Security Subsystem and clock drivers
ARM: s3c64xx: squash samsung_usb_phy.h into setup-usb-phy.c
ARM: debug-ll: Add support for r7s9210
...
- 52-bit virtual addressing in the kernel
- New ABI to allow tagged user pointers to be dereferenced by syscalls
- Early RNG seeding by the bootloader
- Improve robustness of SMP boot
- Fix TLB invalidation in light of recent architectural clarifications
- Support for i.MX8 DDR PMU
- Remove direct LSE instruction patching in favour of static keys
- Function error injection using kprobes
- Support for the PPTT "thread" flag introduced by ACPI 6.3
- Move PSCI idle code into proper cpuidle driver
- Relaxation of implicit I/O memory barriers
- Build with RELR relocations when toolchain supports them
- Numerous cleanups and non-critical fixes
-----BEGIN PGP SIGNATURE-----
iQFEBAABCgAuFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAl1yYREQHHdpbGxAa2Vy
bmVsLm9yZwAKCRC3rHDchMFjNAM3CAChqDFQkryXoHwdeEcaukMRVNxtxOi4pM4g
5xqkb7PoqRJssIblsuhaXjrSD97yWCgaqCmFe6rKoes++lP4bFcTe22KXPPyPBED
A+tK4nTuKKcZfVbEanUjI+ihXaHJmKZ/kwAxWsEBYZ4WCOe3voCiJVNO2fHxqg1M
8TskZ2BoayTbWMXih0eJg2MCy/xApBq4b3nZG4bKI7Z9UpXiKN1NYtDh98ZEBK4V
d/oNoHsJ2ZvIQsztoBJMsvr09DTCazCijWZiECadm6l41WEPFizngrACiSJLLtYo
0qu4qxgg9zgFlvBCRQmIYSggTuv35RgXSfcOwChmW5DUjHG+f9GK
=Ru4B
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Will Deacon:
"Although there isn't tonnes of code in terms of line count, there are
a fair few headline features which I've noted both in the tag and also
in the merge commits when I pulled everything together.
The part I'm most pleased with is that we had 35 contributors this
time around, which feels like a big jump from the usual small group of
core arm64 arch developers. Hopefully they all enjoyed it so much that
they'll continue to contribute, but we'll see.
It's probably worth highlighting that we've pulled in a branch from
the risc-v folks which moves our CPU topology code out to where it can
be shared with others.
Summary:
- 52-bit virtual addressing in the kernel
- New ABI to allow tagged user pointers to be dereferenced by
syscalls
- Early RNG seeding by the bootloader
- Improve robustness of SMP boot
- Fix TLB invalidation in light of recent architectural
clarifications
- Support for i.MX8 DDR PMU
- Remove direct LSE instruction patching in favour of static keys
- Function error injection using kprobes
- Support for the PPTT "thread" flag introduced by ACPI 6.3
- Move PSCI idle code into proper cpuidle driver
- Relaxation of implicit I/O memory barriers
- Build with RELR relocations when toolchain supports them
- Numerous cleanups and non-critical fixes"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (114 commits)
arm64: remove __iounmap
arm64: atomics: Use K constraint when toolchain appears to support it
arm64: atomics: Undefine internal macros after use
arm64: lse: Make ARM64_LSE_ATOMICS depend on JUMP_LABEL
arm64: asm: Kill 'asm/atomic_arch.h'
arm64: lse: Remove unused 'alt_lse' assembly macro
arm64: atomics: Remove atomic_ll_sc compilation unit
arm64: avoid using hard-coded registers for LSE atomics
arm64: atomics: avoid out-of-line ll/sc atomics
arm64: Use correct ll/sc atomic constraints
jump_label: Don't warn on __exit jump entries
docs/perf: Add documentation for the i.MX8 DDR PMU
perf/imx_ddr: Add support for AXI ID filtering
arm64: kpti: ensure patched kernel text is fetched from PoU
arm64: fix fixmap copy for 16K pages and 48-bit VA
perf/smmuv3: Validate groups for global filtering
perf/smmuv3: Validate group size
arm64: Relax Documentation/arm64/tagged-pointers.rst
arm64: kvm: Replace hardcoded '1' with SYS_PAR_EL1_F
arm64: mm: Ignore spurious translation faults taken from the kernel
...
Now that the Xen special cases are gone nothing worth mentioning is
left in the arm64 <asm/dma-mapping.h> file, so switch to use the
asm-generic version instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Will Deacon <will@kernel.org>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Jonathan Marek
Amit Kucheria
Hsin-Yi Wang
Andre Przywara
Marek Behún
Neil Armstrong
Luke Nelson
Daniel Thompson
Gavin Shan
Marc Zyngier
James Morse
Nick Desaulniers
Johan Jonker
Keno Fischer
Yoshihiro Shimoda
Adam Ford
Chen-Yu Tsai
Christoph Hellwig
Mark Rutland
Jason A. Donenfeld
Vincenzo Frascino
Fangrui Song
Arnd Bergmann
Catalin Marinas
Russell King
Jon Hunter
Vidya Sagar
Jernej Skrabec
Angus Ainslie (Purism)
Mark Brown
Fredrik Strupe
Dave Gerlach
Maxime Ripard
Madalin Bucur
Ilie Halip
Madalin Bucur
Cristian Marussi
Christian Hewitt
Fabio Estevam
Guillaume La Roque
Ley Foon Tan
Will Deacon
Lokesh Vutla
Sami Tolvanen
Bjorn Andersson
Manu Gautam
Robin Murphy
Suzuki K Poulose
Baruch Siach
Kuninori Morimoto
Jeffrey Hugo
Niklas Cassel
Ard Biesheuvel
Christoffer Dall
Dirk Behme
Andrew Murray
Sudeep Holla
Rob Clark
S.j. Wang
Biju Das
Miquel Raynal
Kieran Bingham
Jerome Brunet
Sai Prakash Ranjan
Dinh Nguyen
Stefan Mavrodiev
Yinbo Zhu
Loic Poulain
Yunfeng Ye
Amanieu d'Antras
Wei Li
Michael Walle
Anand Moon
David Hildenbrand
Marek Szyprowski
Linus Torvalds
Pavel Tatashin
Huacai Chen
Olof Johansson
Lucas Stach
Florian Fainelli
Doug Berger
Yuantian Tang
Paolo Bonzini
Yang Yingliang
Julien Thierry
Julien Grall
Anson Huang
Ran Wang
Chris von Recklinghausen
Douglas Anderson
Vivek Unune
Soeren Moch
Marc Zyngier
Maxime Ripard
Hugh Cole-Baker
Juergen Gross
Masayoshi Mizuma
Thierry Reding
Rayagonda Kokatanur
Vasily Khoruzhick
Keerthy
Alexandre Ghiti
Mike Rapoport
Nicholas Piggin
Matthew Wilcox (Oracle)
Bjorn Helgaas
Jeremy Cline
David S. Miller
Andrey Smirnov