* 'x86-setup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
vgacon: Add support for setting the default cursor state
vc: Add support for hiding the cursor when creating VTs
x86, setup: Store the boot cursor state
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1815 commits)
mac80211: fix reorder buffer release
iwmc3200wifi: Enable wimax core through module parameter
iwmc3200wifi: Add wifi-wimax coexistence mode as a module parameter
iwmc3200wifi: Coex table command does not expect a response
iwmc3200wifi: Update wiwi priority table
iwlwifi: driver version track kernel version
iwlwifi: indicate uCode type when fail dump error/event log
iwl3945: remove duplicated event logging code
b43: fix two warnings
ipw2100: fix rebooting hang with driver loaded
cfg80211: indent regulatory messages with spaces
iwmc3200wifi: fix NULL pointer dereference in pmkid update
mac80211: Fix TX status reporting for injected data frames
ath9k: enable 2GHz band only if the device supports it
airo: Fix integer overflow warning
rt2x00: Fix padding bug on L2PAD devices.
WE: Fix set events not propagated
b43legacy: avoid PPC fault during resume
b43: avoid PPC fault during resume
tcp: fix a timewait refcnt race
...
Fix up conflicts due to sysctl cleanups (dead sysctl_check code and
CTL_UNNUMBERED removed) in
kernel/sysctl_check.c
net/ipv4/sysctl_net_ipv4.c
net/ipv6/addrconf.c
net/sctp/sysctl.c
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (30 commits)
x86, apic: Enable lapic nmi watchdog on AMD Family 11h
x86: Remove unnecessary mdelay() from cpu_disable_common()
x86, ioapic: Document another case when level irq is seen as an edge
x86, ioapic: Fix the EOI register detection mechanism
x86, io-apic: Move the effort of clearing remoteIRR explicitly before migrating the irq
x86: SGI UV: Map low MMR ranges
x86: apic: Print out SRAT table APIC id in hex
x86: Re-get cfg_new in case reuse/move irq_desc
x86: apic: Remove not needed #ifdef
x86: io-apic: IO-APIC MMIO should not fail on resource insertion
x86: Remove asm/apicnum.h
x86: apic: Do not use stacked physid_mask_t
x86, apic: Get rid of apicid_to_cpu_present assign on 64-bit
x86, ioapic: Use snrpintf while set names for IO-APIC resourses
x86, apic: Use PAGE_SIZE instead of numbers
x86: Remove local_irq_enable()/local_irq_disable() in fixup_irqs()
x86: Use EOI register in io-apic on intel platforms
x86: Force irq complete move during cpu offline
x86: Remove move_cleanup_count from irq_cfg
x86, intr-remap: Avoid irq_chip mask/unmask in fixup_irqs() for intr-remapping
...
* 'tracing-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (40 commits)
tracing: Separate raw syscall from syscall tracer
ring-buffer-benchmark: Add parameters to set produce/consumer priorities
tracing, function tracer: Clean up strstrip() usage
ring-buffer benchmark: Run producer/consumer threads at nice +19
tracing: Remove the stale include/trace/power.h
tracing: Only print objcopy version warning once from recordmcount
tracing: Prevent build warning: 'ftrace_graph_buf' defined but not used
ring-buffer: Move access to commit_page up into function used
tracing: do not disable interrupts for trace_clock_local
ring-buffer: Add multiple iterations between benchmark timestamps
kprobes: Sanitize struct kretprobe_instance allocations
tracing: Fix to use __always_unused attribute
compiler: Introduce __always_unused
tracing: Exit with error if a weak function is used in recordmcount.pl
tracing: Move conditional into update_funcs() in recordmcount.pl
tracing: Add regex for weak functions in recordmcount.pl
tracing: Move mcount section search to front of loop in recordmcount.pl
tracing: Fix objcopy revision check in recordmcount.pl
tracing: Check absolute path of input file in recordmcount.pl
tracing: Correct the check for number of arguments in recordmcount.pl
...
Add support for setting a global default for whether or not a visible
cursor should be enabled when creating VCs. The default will be to do so,
unless overridden by the user at boot time or by a driver.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
LKML-Reference: <1258143251-5818-1-git-send-email-mjg@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
When the system has too many timers or too many aggregate
queued signals, the EAGAIN error is returned to application
from kernel, including timer_create() [POSIX.1b].
It means that the app exceeded the limit of pending signals,
but in general application writers do not expect this
outcome and the current silent failure can cause rare app
failures under very high load.
This patch adds a new message when we reach the limit
and if print_fatal_signals is enabled:
task/1234: reached RLIMIT_SIGPENDING, dropping signal
If you see this message and your system behaved unexpectedly,
you can run following command to lift the limit:
# ulimit -i unlimited
With help from Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>.
Signed-off-by: Naohiro Ooiwa <nooiwa@miraclelinux.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Cc: Roland McGrath <roland@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: oleg@redhat.com
LKML-Reference: <4AF6E7E2.9080406@miraclelinux.com>
[ Modified a few small details, gave surrounding code some love. ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We're adding enough nfs documentation that it may as well have its own
subdirectory.
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Remove the root_plug example LSM code. It's unmaintained and
increasingly broken in various ways.
Made at the 2009 Kernel Summit in Tokyo!
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: James Morris <jmorris@namei.org>
Add a command line parameter to allow limiting the function graphs
that are traced on boot up from the given top-level callers , when
ftrace=function_graph is specified.
This patch adds the following command line option:
ftrace_graph_filter=function-list
Where function-list is a comma separated list of functions to filter.
[fweisbec@gmail.com: picked the documentation changes from the v2 patch]
Signed-off-by: Stefan Assmann <sassmann@redhat.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
LKML-Reference: <4AD2DEB9.2@redhat.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
UDP_HTABLE_SIZE was initialy defined to 128, which is a bit small for
several setups.
4000 active UDP sockets -> 32 sockets per chain in average. An
incoming frame has to lookup all sockets to find best match, so long
chains hurt latency.
Instead of a fixed size hash table that cant be perfect for every
needs, let UDP stack choose its table size at boot time like tcp/ip
route, using alloc_large_system_hash() helper
Add an optional boot parameter, uhash_entries=x so that an admin can
force a size between 256 and 65536 if needed, like thash_entries and
rhash_entries.
dmesg logs two new lines :
[ 0.647039] UDP hash table entries: 512 (order: 0, 4096 bytes)
[ 0.647099] UDP Lite hash table entries: 512 (order: 0, 4096 bytes)
Maximal size on 64bit arches would be 65536 slots, ie 1 MBytes for non
debugging spinlocks.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c953094 ("early_printk: Allow more than one early console")
introduced a regression in the parsing of the earlyprintk= kernel
arguments.
If you specify "earlyprintk=serial,ttyS0,115200" as a kernel
argument, the "serial,ttyS" should be parsed as a single argument
and not as "serial" and then "ttyS".
Also update the documentation to reflect you can specify the ttyS
directly without the "serial" argument.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <gregkh@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
LKML-Reference: <4ABB7D5E.6000301@windriver.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add missing information about requirements of using the EHCI usb debug
controller as well as to mention you can use a debug controller other
than the first one in the system.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Sarah Sharp <sarah.a.sharp@intel.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (262 commits)
sh: mach-ecovec24: Add user debug switch support
sh: Kill off unused se_skipped in alignment trap notification code.
sh: Wire up HAVE_SYSCALL_TRACEPOINTS.
video: sh_mobile_lcdcfb: use both register sets for display panning
video: sh_mobile_lcdcfb: implement display panning
sh: Fix up sh7705 flush_dcache_page() build.
sh: kfr2r09: document the PLL/FLL <-> RF relationship.
sh: mach-ecovec24: need asm/clock.h.
sh: mach-ecovec24: deassert usb irq on boot.
sh: Add KEYSC support for EcoVec24
sh: add kycr2_delay for sh_keysc
sh: cpufreq: Include CPU id in info messages.
sh: multi-evt support for SH-X3 proto CPU.
sh: clkfwk: remove bogus set_bus_parent() from SH7709.
sh: Fix the indication point of the liquid crystal of AP-325RXA(AP3300)
sh: Add EcoVec24 romImage defconfig
sh: USB disable process is needed if romImage boot for EcoVec24
sh: EcoVec24: add HIZA setting for LED
sh: EcoVec24: write MAC address in boot
sh: Add romImage support for EcoVec24
...
The difference between some loongson-based machines is very small, so, if
there is no necessary to add new kernel config options to cope with this
difference, it will be better to share the same kernel image file between
them, benefit from this, the linux distribution developers only have a need
to compile the kernel one time.
This machtype kernel command line argument will be used later to share the
same kernel image file between two different machines(menglong & yeeloong)
made by lemote.
Thanks very much to Zhang Le for cleaning up the machtype implementation.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (46 commits)
powerpc64: convert to dynamic percpu allocator
sparc64: use embedding percpu first chunk allocator
percpu: kill lpage first chunk allocator
x86,percpu: use embedding for 64bit NUMA and page for 32bit NUMA
percpu: update embedding first chunk allocator to handle sparse units
percpu: use group information to allocate vmap areas sparsely
vmalloc: implement pcpu_get_vm_areas()
vmalloc: separate out insert_vmalloc_vm()
percpu: add chunk->base_addr
percpu: add pcpu_unit_offsets[]
percpu: introduce pcpu_alloc_info and pcpu_group_info
percpu: move pcpu_lpage_build_unit_map() and pcpul_lpage_dump_cfg() upward
percpu: add @align to pcpu_fc_alloc_fn_t
percpu: make @dyn_size mandatory for pcpu_setup_first_chunk()
percpu: drop @static_size from first chunk allocators
percpu: generalize first chunk allocator selection
percpu: build first chunk allocators selectively
percpu: rename 4k first chunk allocator to page
percpu: improve boot messages
percpu: fix pcpu_reclaim() locking
...
Fix trivial conflict as by Tejun Heo in kernel/sched.c
* 'kvm-updates/2.6.32' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (202 commits)
MAINTAINERS: update KVM entry
KVM: correct error-handling code
KVM: fix compile warnings on s390
KVM: VMX: Check cpl before emulating debug register access
KVM: fix misreporting of coalesced interrupts by kvm tracer
KVM: x86: drop duplicate kvm_flush_remote_tlb calls
KVM: VMX: call vmx_load_host_state() only if msr is cached
KVM: VMX: Conditionally reload debug register 6
KVM: Use thread debug register storage instead of kvm specific data
KVM guest: do not batch pte updates from interrupt context
KVM: Fix coalesced interrupt reporting in IOAPIC
KVM guest: fix bogus wallclock physical address calculation
KVM: VMX: Fix cr8 exiting control clobbering by EPT
KVM: Optimize kvm_mmu_unprotect_page_virt() for tdp
KVM: Document KVM_CAP_IRQCHIP
KVM: Protect update_cr8_intercept() when running without an apic
KVM: VMX: Fix EPT with WP bit change during paging
KVM: Use kvm_{read,write}_guest_virt() to read and write segment descriptors
KVM: x86 emulator: Add adc and sbb missing decoder flags
KVM: Add missing #include
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1623 commits)
netxen: update copyright
netxen: fix tx timeout recovery
netxen: fix file firmware leak
netxen: improve pci memory access
netxen: change firmware write size
tg3: Fix return ring size breakage
netxen: build fix for INET=n
cdc-phonet: autoconfigure Phonet address
Phonet: back-end for autoconfigured addresses
Phonet: fix netlink address dump error handling
ipv6: Add IFA_F_DADFAILED flag
net: Add DEVTYPE support for Ethernet based devices
mv643xx_eth.c: remove unused txq_set_wrr()
ucc_geth: Fix hangs after switching from full to half duplex
ucc_geth: Rearrange some code to avoid forward declarations
phy/marvell: Make non-aneg speed/duplex forcing work for 88E1111 PHYs
drivers/net/phy: introduce missing kfree
drivers/net/wan: introduce missing kfree
net: force bridge module(s) to be GPL
Subject: [PATCH] appletalk: Fix skb leak when ipddp interface is not loaded
...
Fixed up trivial conflicts:
- arch/x86/include/asm/socket.h
converted to <asm-generic/socket.h> in the x86 tree. The generic
header has the same new #define's, so that works out fine.
- drivers/net/tun.c
fix conflict between 89f56d1e9 ("tun: reuse struct sock fields") that
switched over to using 'tun->socket.sk' instead of the redundantly
available (and thus removed) 'tun->sk', and 2b980dbd ("lsm: Add hooks
to the TUN driver") which added a new 'tun->sk' use.
Noted in 'next' by Stephen Rothwell.
* git://git.linux-nfs.org/projects/trondmy/nfs-2.6: (87 commits)
NFSv4: Disallow 'mount -t nfs4 -overs=2' and 'mount -t nfs4 -overs=3'
NFS: Allow the "nfs" file system type to support NFSv4
NFS: Move details of nfs4_get_sb() to a helper
NFS: Refactor NFSv4 text-based mount option validation
NFS: Mount option parser should detect missing "port="
NFS: out of date comment regarding O_EXCL above nfs3_proc_create()
NFS: Handle a zero-length auth flavor list
SUNRPC: Ensure that sunrpc gets initialised before nfs, lockd, etc...
nfs: fix compile error in rpc_pipefs.h
nfs: Remove reference to generic_osync_inode from a comment
SUNRPC: cache must take a reference to the cache detail's module on open()
NFS: Use the DNS resolver in the mount code.
NFS: Add a dns resolver for use with NFSv4 referrals and migration
SUNRPC: Fix a typo in cache_pipefs_files
nfs: nfs4xdr: optimize low level decoding
nfs: nfs4xdr: get rid of READ_BUF
nfs: nfs4xdr: simplify decode_exchange_id by reusing decode_opaque_inline
nfs: nfs4xdr: get rid of COPYMEM
nfs: nfs4xdr: introduce decode_sessionid helper
nfs: nfs4xdr: introduce decode_verifier helper
...
This implements support for NMI debugging that was shamelessly copied
from the avr32 port. A bit of special magic is needed in the interrupt
exception path given that the NMI exception handler is stubbed in to the
regular exception handling table despite being reported in INTEVT. So we
mangle the lookup and kick off an EXPEVT-style exception dispatch from
the INTEVT path for exceptions that do_IRQ() has no chance of handling.
As a result, we also drop the evt2irq() conversion from the do_IRQ() path
and just do it in assembly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch makes the tsc=reliable option disable the boot time
stability checks. Currently the option only disables the runtime
watchdog checks. This change allows folks who want to override the
boot time TSC stability checks and use the TSC when the system would
otherwise disqualify it.
There still are some situations that the TSC will be disqualified,
such as cpufreq scaling. But these are situations where the box will
hang if allowed.
Patch also includes a fix for an issue found by Thomas Gleixner, where
the TSC disqualification message wouldn't be printed after a call to
unsynchronized_tsc().
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: akataria@vmware.com
Cc: Stephen Hemminger <shemminger@vyatta.com>
LKML-Reference: <1250552447.7212.92.camel@localhost.localdomain>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The NFSv4 and NFSv4.1 protocols both allow for the redirection of a client
from one server to another in order to support filesystem migration and
replication. For full protocol support, we need to add the ability to
convert a DNS host name into an IP address that we can feed to the RPC
client.
We'll reuse the sunrpc cache, now that it has been converted to work with
rpc_pipefs.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
With x86 converted to embedding allocator, lpage doesn't have any user
left. Kill it along with cpa handling code.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jan Beulich <JBeulich@novell.com>
Now that all first chunk allocators are in mm/percpu.c, it makes sense
to make generalize percpu_alloc kernel parameter. Define PCPU_FC_*
and set pcpu_chosen_fc using early_param() in mm/percpu.c. Arch code
can use the set value to determine which first chunk allocator to use.
Signed-off-by: Tejun Heo <tj@kernel.org>
Page size isn't always 4k depending on arch and configuration. Rename
4k first chunk allocator to page.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: David Howells <dhowells@redhat.com>
By default the kernel honors the HPA (host protected area) of hard
drives. Using libata's ignore_hpa module option it's possible to
change this behaviour.
Document usage and options of libata.ignore_hpa in
Documentation/kernel-parameters.txt.
Signed-off-by: Michael Prokop <mika@grml.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Parameters like the minimum reserved port, and the number of slot entries
should really be module parameters rather than sysctls.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
* 'core-fixes-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
dma-debug: Fix the overlap() function to be correct and readable
oprofile: reset bt_lost_no_mapping with other stats
x86/oprofile: rename kernel parameter for architectural perfmon to arch_perfmon
signals: declare sys_rt_tgsigqueueinfo in syscalls.h
rcu: Mark Hierarchical RCU no longer experimental
dma-debug: Put all hash-chain locks into the same lock class
dma-debug: fix off-by-one error in overlap function
The short name of the achitecture is 'arch_perfmon'. This patch
changes the kernel parameter to use this name.
Cc: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Robert Richter <robert.richter@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Some PHYs require longer timeouts for carrier detection, and
auto-negotiation process may take indefinite amount of time.
It may be inconvenient to force longer timeouts for sane PHYs,
so let's introduce a kernel command line option.
Since we're using module_param(), the option also can be
changed in runtime.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already have ftrace= boot option, and this adds a similar
boot option for trace events, so allow trace events to be
enabled at boot, for boot debugging purpose.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <4A4ACE29.3010407@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, delay: tsc based udelay should have rdtsc_barrier
x86, setup: correct include file in <asm/boot.h>
x86, setup: Fix typo "CONFIG_x86_64" in <asm/boot.h>
x86, mce: percpu mcheck_timer should be pinned
x86: Add sysctl to allow panic on IOCK NMI error
x86: Fix uv bau sending buffer initialization
x86, mce: Fix mce resume on 32bit
x86: Move init_gbpages() to setup_arch()
x86: ensure percpu lpage doesn't consume too much vmalloc space
x86: implement percpu_alloc kernel parameter
x86: fix pageattr handling for lpage percpu allocator and re-enable it
x86: reorganize cpa_process_alias()
x86: prepare setup_pcpu_lpage() for pageattr fix
x86: rename remap percpu first chunk allocator to lpage
x86: fix duplicate free in setup_pcpu_remap() failure path
percpu: fix too lazy vunmap cache flushing
x86: Set cpu_llc_id on AMD CPUs
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
ftrace: Fix the output of profile
ring-buffer: Make it generally available
ftrace: Remove duplicate newline
tracing: Fix trace_buf_size boot option
ftrace: Fix t_hash_start()
ftrace: Don't manipulate @pos in t_start()
ftrace: Don't increment @pos in g_start()
tracing: Reset iterator in t_start()
trace_stat: Don't increment @pos in seq start()
tracing_bprintk: Don't increment @pos in t_start()
tracing/events: Don't increment @pos in s_start()
This reverts commit 9e9f46c44e.
Quoting from the commit message:
"At this point, it seems to solve more problems than it causes, so let's
try using it by default. It's an easy revert if it ends up causing
trouble."
And guess what? The _CRS code causes trouble.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We should be able to specify [KMG] when setting trace_buf_size
boot option, as documented in kernel-parameters.txt
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <4A41F2DB.4020102@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* git://git.infradead.org/~dwmw2/iommu-2.6.31:
intel-iommu: Fix one last ia64 build problem in Pass Through Support
VT-d: support the device IOTLB
VT-d: cleanup iommu_flush_iotlb_psi and flush_unmaps
VT-d: add device IOTLB invalidation support
VT-d: parse ATSR in DMA Remapping Reporting Structure
PCI: handle Virtual Function ATS enabling
PCI: support the ATS capability
intel-iommu: dmar_set_interrupt return error value
intel-iommu: Tidy up iommu->gcmd handling
intel-iommu: Fix tiny theoretical race in write-buffer flush.
intel-iommu: Clean up handling of "caching mode" vs. IOTLB flushing.
intel-iommu: Clean up handling of "caching mode" vs. context flushing.
VT-d: fix invalid domain id for KVM context flush
Fix !CONFIG_DMAR build failure introduced by Intel IOMMU Pass Through Support
Intel IOMMU Pass Through Support
Fix up trivial conflicts in drivers/pci/{intel-iommu.c,intr_remapping.c}
* git://git.infradead.org/mtd-2.6: (63 commits)
mtd: OneNAND: Allow setting of boundary information when built as module
jffs2: leaking jffs2_summary in function jffs2_scan_medium
mtd: nand: Fix memory leak on txx9ndfmc probe failure.
mtd: orion_nand: use burst reads with double word accesses
mtd/nand: s3c6400 support for s3c2410 driver
[MTD] [NAND] S3C2410: Use DIV_ROUND_UP
[MTD] [NAND] S3C2410: Deal with unaligned lengths in S3C2440 buffer read/write
[MTD] [NAND] S3C2410: Allow the machine code to get the BBT table from NAND
[MTD] [NAND] S3C2410: Added a kerneldoc for s3c2410_nand_set
mtd: physmap_of: Add multiple regions and concatenation support
mtd: nand: max_retries off by one in mxc_nand
mtd: nand: s3c2410_nand_setrate(): use correct macros for 2412/2440
mtd: onenand: add bbt_wait & unlock_all as replaceable for some platform
mtd: Flex-OneNAND support
mtd: nand: add OMAP2/OMAP3 NAND driver
mtd: maps: Blackfin async: fix memory leaks in probe/remove funcs
mtd: uclinux: mark local stuff static
mtd: uclinux: do not allow to be built as a module
mtd: uclinux: allow systems to override map addr/size
mtd: blackfin NFC: fix hang when using NAND on BF527-EZKITs
...
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (49 commits)
[ARM] idle: clean up pm_idle calling, obey hlt_counter
[ARM] S3C: Fix gpio-config off-by-one bug
[ARM] S3C64XX: add to_irq() support for EINT() GPIO
[ARM] S3C64XX: clock.c: fix typo in usb-host clock ctrlbit
[ARM] S3C64XX: fix HCLK gate defines
[ARM] Update mach-types
[ARM] wire up rt_tgsigqueueinfo and perf_counter_open
OMAP2 clock/powerdomain: off by 1 error in loop timeout comparisons
OMAP3 SDRC: set FIXEDDELAY when disabling SDRC DLL
OMAP3: Add support for DPLL3 divisor values higher than 2
OMAP3 SRAM: convert SRAM code to use macros rather than magic numbers
OMAP3 SRAM: add more comments on the SRAM code
OMAP3 clock/SDRC: program SDRC_MR register during SDRC clock change
OMAP3 clock: add a short delay when lowering CORE clk rate
OMAP3 clock: initialize SDRC timings at kernel start
OMAP3 clock: remove wait for DPLL3 M2 clock to stabilize
[ARM] Add old Feroceon support to compressed/head.S
[ARM] 5559/1: Limit the stack unwinding caused by a kthread exit
[ARM] 5558/1: Add extra checks to ARM unwinder to avoid tracing corrupt stacks
[ARM] 5557/1: Discard some ARM.ex*.*exit.text sections when !HOTPLUG or !HOTPLUG_CPU
...
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (74 commits)
PCI: make msi_free_irqs() to use msix_mask_irq() instead of open coded write
PCI: Fix the NIU MSI-X problem in a better way
PCI ASPM: remove get_root_port_link
PCI ASPM: cleanup pcie_aspm_sanity_check
PCI ASPM: remove has_switch field
PCI ASPM: cleanup calc_Lx_latency
PCI ASPM: cleanup pcie_aspm_get_cap_device
PCI ASPM: cleanup clkpm checks
PCI ASPM: cleanup __pcie_aspm_check_state_one
PCI ASPM: cleanup initialization
PCI ASPM: cleanup change input argument of aspm functions
PCI ASPM: cleanup misc in struct pcie_link_state
PCI ASPM: cleanup clkpm state in struct pcie_link_state
PCI ASPM: cleanup latency field in struct pcie_link_state
PCI ASPM: cleanup aspm state field in struct pcie_link_state
PCI ASPM: fix typo in struct pcie_link_state
PCI: drivers/pci/slot.c should depend on CONFIG_SYSFS
PCI: remove redundant __msi_set_enable()
PCI PM: consistently use type bool for wake enable variable
x86/ACPI: Correct maximum allowed _CRS returned resources and warn if exceeded
...
According to Andi, it isn't clear whether lpage allocator is worth the
trouble as there are many processors where PMD TLB is far scarcer than
PTE TLB. The advantage or disadvantage probably depends on the actual
size of percpu area and specific processor. As performance
degradation due to TLB pressure tends to be highly workload specific
and subtle, it is difficult to decide which way to go without more
data.
This patch implements percpu_alloc kernel parameter to allow selecting
which first chunk allocator to use to ease debugging and testing.
While at it, make sure all the failure paths report why something
failed to help determining why certain allocator isn't working. Also,
kill the "Great future plan" comment which had already been realized
quite some time ago.
[ Impact: allow explicit percpu first chunk allocator selection ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Jan Beulich <JBeulich@novell.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ingo Molnar <mingo@elte.hu>
Enable the use of GCC's coverage testing tool gcov [1] with the Linux
kernel. gcov may be useful for:
* debugging (has this code been reached at all?)
* test improvement (how do I change my test to cover these lines?)
* minimizing kernel configurations (do I need this option if the
associated code is never run?)
The profiling patch incorporates the following changes:
* change kbuild to include profiling flags
* provide functions needed by profiling code
* present profiling data as files in debugfs
Note that on some architectures, enabling gcc's profiling option
"-fprofile-arcs" for the entire kernel may trigger compile/link/
run-time problems, some of which are caused by toolchain bugs and
others which require adjustment of architecture code.
For this reason profiling the entire kernel is initially restricted
to those architectures for which it is known to work without changes.
This restriction can be lifted once an architecture has been tested
and found compatible with gcc's profiling. Profiling of single files
or directories is still available on all platforms (see config help
text).
[1] http://gcc.gnu.org/onlinedocs/gcc/Gcov.html
Signed-off-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Li Wei <W.Li@Sun.COM>
Cc: Michael Ellerman <michaele@au1.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Heiko Carstens <heicars2@linux.vnet.ibm.com>
Cc: Martin Schwidefsky <mschwid2@linux.vnet.ibm.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The console blank timer is currently hardcoded to 10*60 seconds which
might be annoying on systems with no input devices attached to wake up the
console again. Especially during development, disabling the screen saver
can be handy - for example when debugging the root fs mount mechanism or
other scenarios where no userspace program could be started to do that at
runtime from userspace.
This patch defines a core_param for the variable in charge which allows
users to entirely disable the blank feature at boot time by setting it 0.
The value can still be overwritten at runtime using the standard ioctl
call - this just allows to conditionally change the default.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Also explains why the touchscreen support is not present,
and were to find a working one...
Signed-off-by: Michel Pollet <buserror@gmail.com>
[ben-linux@fluff.org: Fix header description]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (103 commits)
powerpc: Fix bug in move of altivec code to vector.S
powerpc: Add support for swiotlb on 32-bit
powerpc/spufs: Remove unused error path
powerpc: Fix warning when printing a resource_size_t
powerpc/xmon: Remove unused variable in xmon.c
powerpc/pseries: Fix warnings when printing resource_size_t
powerpc: Shield code specific to 64-bit server processors
powerpc: Separate PACA fields for server CPUs
powerpc: Split exception handling out of head_64.S
powerpc: Introduce CONFIG_PPC_BOOK3S
powerpc: Move VMX and VSX asm code to vector.S
powerpc: Set init_bootmem_done on NUMA platforms as well
powerpc/mm: Fix a AB->BA deadlock scenario with nohash MMU context lock
powerpc/mm: Fix some SMP issues with MMU context handling
powerpc: Add PTRACE_SINGLEBLOCK support
fbdev: Add PLB support and cleanup DCR in xilinxfb driver.
powerpc/virtex: Add ml510 reference design device tree
powerpc/virtex: Add Xilinx ML510 reference design support
powerpc/virtex: refactor intc driver and add support for i8259 cascading
powerpc/virtex: Add support for Xilinx PCI host bridge
...
* 'for-2.6.31' of git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (29 commits)
ide: re-implement ide_pci_init_one() on top of ide_pci_init_two()
ide: unexport ide_find_dma_mode()
ide: fix PowerMac bootup oops
ide: skip probe if there are no devices on the port (v2)
sl82c105: add printk() logging facility
ide-tape: fix proc warning
ide: add IDE_DFLAG_NIEN_QUIRK device flag
ide: respect quirk_drives[] list on all controllers
hpt366: enable all quirks for devices on quirk_drives[] list
hpt366: sync quirk_drives[] list with pdc202xx_{new,old}.c
ide: remove superfluous SELECT_MASK() call from do_rw_taskfile()
ide: remove superfluous SELECT_MASK() call from ide_driveid_update()
icside: remove superfluous ->maskproc method
ide-tape: fix IDE_AFLAG_* atomic accesses
ide-tape: change IDE_AFLAG_IGNORE_DSC non-atomically
pdc202xx_old: kill resetproc() method
pdc202xx_old: don't call pdc202xx_reset() on IRQ timeout
pdc202xx_old: use ide_dma_test_irq()
ide: preserve Host Protected Area by default (v2)
ide-gd: implement block device ->set_capacity method (v2)
...
* 'for-linus' of git://linux-arm.org/linux-2.6:
kmemleak: Add the corresponding MAINTAINERS entry
kmemleak: Simple testing module for kmemleak
kmemleak: Enable the building of the memory leak detector
kmemleak: Remove some of the kmemleak false positives
kmemleak: Add modules support
kmemleak: Add kmemleak_alloc callback from alloc_large_system_hash
kmemleak: Add the vmalloc memory allocation/freeing hooks
kmemleak: Add the slub memory allocation/freeing hooks
kmemleak: Add the slob memory allocation/freeing hooks
kmemleak: Add the slab memory allocation/freeing hooks
kmemleak: Add documentation on the memory leak detector
kmemleak: Add the base support
Manual conflict resolution (with the slab/earlyboot changes) in:
drivers/char/vt.c
init/main.c
mm/slab.c
Adds support for PCI Express transaction layer end-to-end CRC checking
(ECRC). This patch will enable/disable ECRC checking by setting/clearing
the ECRC Check Enable and/or ECRC Generation Enable bits for devices that
support ECRC.
The ECRC setting is controlled by the "pci=ecrc=<policy>" command-line
option. If this option is not set or is set to 'bios", the enable and
generation bits are left in whatever state that firmware/BIOS set them to.
The "off" setting turns them off, and the "on" option turns them on (if the
device supports it).
Turning ECRC on or off can be a data integrity versus performance
tradeoff. In theory, turning it on will catch more data errors, turning
it off means possibly better performance since CRC does not need to be
calculated by the PCIe hardware and packet sizes are reduced.
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
At this point, it seems to solve more problems than it causes, so let's try using it by default. It's an easy revert if it ends up causing trouble.
Reviewed-by: Yinghai Lu <yhlu.kernel@gmail.com>
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch adds the Documentation/kmemleak.txt file with some
information about how kmemleak works.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
* 'tracing-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (244 commits)
Revert "x86, bts: reenable ptrace branch trace support"
tracing: do not translate event helper macros in print format
ftrace/documentation: fix typo in function grapher name
tracing/events: convert block trace points to TRACE_EVENT(), fix !CONFIG_BLOCK
tracing: add protection around module events unload
tracing: add trace_seq_vprint interface
tracing: fix the block trace points print size
tracing/events: convert block trace points to TRACE_EVENT()
ring-buffer: fix ret in rb_add_time_stamp
ring-buffer: pass in lockdep class key for reader_lock
tracing: add annotation to what type of stack trace is recorded
tracing: fix multiple use of __print_flags and __print_symbolic
tracing/events: fix output format of user stack
tracing/events: fix output format of kernel stack
tracing/trace_stack: fix the number of entries in the header
ring-buffer: discard timestamps that are at the start of the buffer
ring-buffer: try to discard unneeded timestamps
ring-buffer: fix bug in ring_buffer_discard_commit
ftrace: do not profile functions when disabled
tracing: make trace pipe recognize latency format flag
...
* 'oprofile-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
oprofile: introduce module_param oprofile.cpu_type
oprofile: add support for Core i7 and Atom
oprofile: remove undocumented oprofile.p4force option
oprofile: re-add force_arch_perfmon option
* 'iommu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (61 commits)
amd-iommu: remove unnecessary "AMD IOMMU: " prefix
amd-iommu: detach device explicitly before attaching it to a new domain
amd-iommu: remove BUS_NOTIFY_BOUND_DRIVER handling
dma-debug: simplify logic in driver_filter()
dma-debug: disable/enable irqs only once in device_dma_allocations
dma-debug: use pr_* instead of printk(KERN_* ...)
dma-debug: code style fixes
dma-debug: comment style fixes
dma-debug: change hash_bucket_find from first-fit to best-fit
x86: enable GART-IOMMU only after setting up protection methods
amd_iommu: fix lock imbalance
dma-debug: add documentation for the driver filter
dma-debug: add dma_debug_driver kernel command line
dma-debug: add debugfs file for driver filter
dma-debug: add variables and checks for driver filter
dma-debug: fix debug_dma_sync_sg_for_cpu and debug_dma_sync_sg_for_device
dma-debug: use sg_dma_len accessor
dma-debug: use sg_dma_address accessor instead of using dma_address directly
amd-iommu: don't free dma adresses below 512MB with CONFIG_IOMMU_STRESS
amd-iommu: don't preallocate page tables with CONFIG_IOMMU_STRESS
...
From the perspective of most users of recent systems, disabling Host
Protected Area (HPA) can break vendor RAID formats, GPT partitions and
risks corrupting firmware or overwriting vendor system recovery tools.
Unfortunately the original (kernels < 2.6.30) behavior (unconditionally
disabling HPA and using full disk capacity) was introduced at the time
when the main use of HPA was to make the drive look small enough for the
BIOS to allow the system to boot with large capacity drives.
Thus to allow the maximum compatibility with the existing setups (using
HPA and partitioned with HPA disabled) we automically disable HPA if
any partitions overlapping HPA are detected. Additionally HPA can also
be disabled using the "nohpa" module parameter (i.e. "ide_core.nohpa=0.0"
to disable HPA on /dev/hda).
v2:
Fix ->resume HPA support.
While at it:
- remove stale "idebus=" entry from Documentation/kernel-parameters.txt
Cc: Robert Hancock <hancockrwd@gmail.com>
Cc: Frans Pop <elendil@planet.nl>
Cc: "Andries E. Brouwer" <Andries.Brouwer@cwi.nl>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
[patch description was based on input from Alan Cox and Frans Pop]
Emphatically-Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Merge reason: This branch was on an -rc5 base so pull almost-2.6.30
to resync with the latest upstream fixes and make sure
the combination works fine.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add support for Samsung Flex-OneNAND devices.
Flex-OneNAND combines SLC and MLC technologies into a single device.
SLC area provides increased reliability and speed, suitable for storing
code such as bootloader, kernel and root file system. MLC area
provides high density and is suitable for storing user data.
SLC and MLC regions can be configured through kernel parameter.
[akpm@linux-foundation.org: export flexoand_region and onenand_addr]
Signed-off-by: Rohit Hagargundgi <h.rohit@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Vishak G <vishak.g@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
When using ftrace=function on the command line to trace functions
on boot up, one can not filter out functions that are commonly called.
This patch adds two new ftrace command line commands.
ftrace_notrace=function-list
ftrace_filter=function-list
Where function-list is a comma separated list of functions to filter.
The ftrace_notrace will make the functions listed not be included
in the function tracing, and ftrace_filter will only trace the functions
listed.
These two act the same as the debugfs/tracing/set_ftrace_notrace and
debugfs/tracing/set_ftrace_filter respectively.
The simple glob expressions that are allowed by the filter files can also
be used by the command line interface.
ftrace_notrace=rcu*,*lock,*spin*
Will not trace any function that starts with rcu, ends with lock, or has
the word spin in it.
Note, if the self tests are enabled, they may interfere with the filtering
set by the command lines.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Conflicts:
arch/mips/sibyte/bcm1480/irq.c
arch/mips/sibyte/sb1250/irq.c
Merge reason: we gathered a few conflicts plus update to latest upstream fixes.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The kmemtrace.enable kernel parameter no longer works. To enable
kmemtrace at boot-time, you must pass "ftrace=kmemtrace" instead.
[ Impact: remove obsolete kernel parameter documentation ]
Cc: Eduard - Gabriel Munteanu <eduard.munteanu@linux360.ro>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
LKML-Reference: <alpine.DEB.2.00.0905241112190.10296@rocky>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Introduce "noxsave" boot parameter which will disable the cpu's xsave/xrstor
capabilities. Useful for debugging and working around xsave related issues.
[ Impact: make it possible to debug problems in the field ]
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The IMA TCB policy is dangerous. A normal use can use all of a system's
memory (which cannot be freed) simply by building and running lots of
executables. The TCB policy is also nearly useless because logging in as root
often causes a policy violation when dealing with utmp, thus rendering the
measurements meaningless.
There is no good fix for this in the kernel. A full TCB policy would need to
be loaded in userspace using LSM rule matching to get both a protected and
useful system. But, if too little is measured before userspace can load a real
policy one again ends up with a meaningless set of measurements. One option
would be to put the policy load inside the initrd in order to get it early
enough in the boot sequence to be useful, but this runs into trouble with the
LSM. For IMA to measure the LSM policy and the LSM policy loading mechanism
it needs rules to do so, but we already talked about problems with defaulting
to such broad rules....
IMA also depends on the files being measured to be on an FS which implements
and supports i_version. Since the only FS with this support (ext4) doesn't
even use it by default it seems silly to have any IMA rules by default.
This should reduce the performance overhead of IMA to near 0 while still
letting users who choose to configure their machine as such to inclue the
ima_tcb kernel paramenter and get measurements during boot before they can
load a customized, reasonable policy in userspace.
Signed-off-by: Eric Paris <eparis@redhat.com>
Acked-by: Mimi Zohar <zohar@us.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
Adds support for the "unused" page hint which can be used in shared
memory partitions to flag pages not in use, which will then be stolen
before active pages by the hypervisor when memory needs to be moved to
LPARs in need of additional memory. Failure to mark pages as 'unused'
makes the LPAR slower to give up unused memory to other partitions.
This adds the kernel parameter 'cmo_free_hint' to disable this
functionality.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch removes module_param oprofile.force_arch_perfmon and
introduces oprofile.cpu_type=archperfmon instead. This new parameter
can be reused for other models and architectures.
Currently only archperfmon is supported.
Cc: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
This re-adds the force_arch_perfmon option that was in the original
arch perfmon patchkit. Originally this was rejected in favour
of a generalized perfmon=name option, but it turned out implementing
the later in a reliable way is hard (and it would have been easy
to crash the kernel if a user gets it wrong)
But now Atom and Core i7 support being readded a user would
need to update their oprofile userland to beyond 0.9.4 to use oprofile again
on Atom or Core i7.
To avoid this problem readd the force_arch_perfmon option.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
Change last "i386" to X86-32 as is used throughout the rest of the file.
Change combination of X86-32,X86-64 to just X86, as is done throughout the
rest of the file.
Add a note that hyphens and underscores are equivalent in parameter names,
with examples.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Jan Engelhardt <jengelh@medozas.de>
Cc: Christopher Sylvain <chris.sylvain@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
kernel boot parameter `hashdist' now defaults on for all 64bit NUMA.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The patch adds kernel parameter intel_iommu=pt to set up pass through
mode in context mapping entry. This disables DMAR in linux kernel; but
KVM still runs on VT-d and interrupt remapping still works.
In this mode, kernel uses swiotlb for DMA API functions but other VT-d
functionalities are enabled for KVM. KVM always uses multi level
translation page table in VT-d. By default, pass though mode is disabled
in kernel.
This is useful when people don't want to enable VT-d DMAR in kernel but
still want to use KVM and interrupt remapping for reasons like DMAR
performance concern or debug purpose.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Acked-by: Weidong Han <weidong@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
"nox2apic" was removed from kernel-parameters.txt by mistake, when
entries were sorted in alpha order (commit 0cb55ad2). But this early
parameter is still there, add it back to kernel-parameters.txt.
[ Impact: add boot parameter description ]
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Weidong Han <weidong.han@intel.com>
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: iommu@lists.linux-foundation.org
Cc: allen.m.kay@intel.com
Cc: fenghua.yu@intel.com
LKML-Reference: <1239957736-6161-2-git-send-email-weidong.han@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Re-add missing kernel-parameters documentation that was accidentally
deleted in commit 0cb55ad2.
Thanks to Ingo and Weidong Han for the heads-up on this.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
cc: Ingo Molnar <mingo@elte.hu>
cc: Len Brown <lenb@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
"nox2apic" was removed from kernel-parameters.txt by mistake, when
entries were sorted in alpha order (commit 0cb55ad2). But this early
parameter is still there, add it back to kernel-parameters.txt.
[ Impact: add boot parameter description ]
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Weidong Han <weidong.han@intel.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: iommu@lists.linux-foundation.org
Cc: dwmw2@infradead.org
Cc: allen.m.kay@intel.com
Cc: fenghua.yu@intel.com
LKML-Reference: <1239957736-6161-2-git-send-email-weidong.han@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
X86 is same as X86-32+X86-64 so replace X86-32,X86-64 with X86.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
LKML-Reference: <1239698023.3033.37.camel@ht.satnam>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Move entries to be in alpha order as specified near the beginning
of this file.
Clean up some whitespace and line-length miscues.
Add '=' to "selinux" option syntax.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (23 commits)
sh: sh7785lcr: Map whole PCI address space.
sh: Fix up DSP context save/restore.
sh: Fix up number of on-chip DMA channels on SH7091.
sh: update defconfigs.
sh: Kill off broken direct-mapped cache mode.
sh: Wire up ARCH_HAS_DEFAULT_IDLE for cpuidle.
sh: Add a command line option for disabling I/O trapping.
sh: Select ARCH_HIBERNATION_POSSIBLE.
sh: migor: Fix up CEU use flags.
input: migor_ts: add wakeup support
rtc: rtc-sh: use set_irq_wake()
input: sh_keysc: use enable/disable_irq_wake()
sh: intc: set_irq_wake() support
sh: intc: install enable, disable and shutdown callbacks
clocksource: sh_cmt: use remove_irq() and remove clockevent workaround
sh: ap325 and Migo-R use new sh_mobile_ceu_info flags
sh: Fix up -Wformat-security whining.
sh: ap325rxa: Add ov772x support, again.
sh: Sanitize asm/mmu.h for assembly use.
sh: Tidy up sh7786 pinmux table.
...
* 'tracing-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (413 commits)
tracing, net: fix net tree and tracing tree merge interaction
tracing, powerpc: fix powerpc tree and tracing tree interaction
ring-buffer: do not remove reader page from list on ring buffer free
function-graph: allow unregistering twice
trace: make argument 'mem' of trace_seq_putmem() const
tracing: add missing 'extern' keywords to trace_output.h
tracing: provide trace_seq_reserve()
blktrace: print out BLK_TN_MESSAGE properly
blktrace: extract duplidate code
blktrace: fix memory leak when freeing struct blk_io_trace
blktrace: fix blk_probes_ref chaos
blktrace: make classic output more classic
blktrace: fix off-by-one bug
blktrace: fix the original blktrace
blktrace: fix a race when creating blk_tree_root in debugfs
blktrace: fix timestamp in binary output
tracing, Text Edit Lock: cleanup
tracing: filter fix for TRACE_EVENT_FORMAT events
ftrace: Using FTRACE_WARN_ON() to check "freed record" in ftrace_release()
x86: kretprobe-booster interrupt emulation code fix
...
Fix up trivial conflicts in
arch/parisc/include/asm/ftrace.h
include/linux/memory.h
kernel/extable.c
kernel/module.c
* 'core/debugobjects' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
debugobjects: delay free of internal objects
debugobjects: replace static objects when slab cache becomes available
debug_objects: add boot-parameter toggle to turn object debugging off again
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (28 commits)
trivial: Update my email address
trivial: NULL noise: drivers/mtd/tests/mtd_*test.c
trivial: NULL noise: drivers/media/dvb/frontends/drx397xD_fw.h
trivial: Fix misspelling of "Celsius".
trivial: remove unused variable 'path' in alloc_file()
trivial: fix a pdlfush -> pdflush typo in comment
trivial: jbd header comment typo fix for JBD_PARANOID_IOFAIL
trivial: wusb: Storage class should be before const qualifier
trivial: drivers/char/bsr.c: Storage class should be before const qualifier
trivial: h8300: Storage class should be before const qualifier
trivial: fix where cgroup documentation is not correctly referred to
trivial: Give the right path in Documentation example
trivial: MTD: remove EOL from MODULE_DESCRIPTION
trivial: Fix typo in bio_split()'s documentation
trivial: PWM: fix of #endif comment
trivial: fix typos/grammar errors in Kconfig texts
trivial: Fix misspelling of firmware
trivial: cgroups: documentation typo and spelling corrections
trivial: Update contact info for Jochen Hein
trivial: fix typo "resgister" -> "register"
...
Enforce strict resource checking - disallowing access by native
drivers to IO ports and memory regions claimed by ACPI firmware.
The patch is mainly aimed to block native hwmon drivers from touching
monitoring chips that ACPI thinks it own.
If this causes a regression, boot with "acpi_enforce_resources=lax"
which was the previous default.
http://bugzilla.kernel.org/show_bug.cgi?id=12376http://bugzilla.kernel.org/show_bug.cgi?id=12541
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Acked-by: Pavel Machek <pavel@suse.cz>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Len Brown <len.brown@intel.com>
This adds a 'noiotrap' kernel command line option to permit disabling of
I/O trapping. This is mostly useful for running on emulators where the
physical device limitations are not an issue.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
As per discussion in:
http://marc.info/?l=linux-arm-kernel&m=123633652517391&w=2
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (88 commits)
PCI: fix HT MSI mapping fix
PCI: don't enable too much HT MSI mapping
x86/PCI: make pci=lastbus=255 work when acpi is on
PCI: save and restore PCIe 2.0 registers
PCI: update fakephp for bus_id removal
PCI: fix kernel oops on bridge removal
PCI: fix conflict between SR-IOV and config space sizing
powerpc/PCI: include pci.h in powerpc MSI implementation
PCI Hotplug: schedule fakephp for feature removal
PCI Hotplug: rename legacy_fakephp to fakephp
PCI Hotplug: restore fakephp interface with complete reimplementation
PCI: Introduce /sys/bus/pci/devices/.../rescan
PCI: Introduce /sys/bus/pci/devices/.../remove
PCI: Introduce /sys/bus/pci/rescan
PCI: Introduce pci_rescan_bus()
PCI: do not enable bridges more than once
PCI: do not initialize bridges more than once
PCI: always scan child buses
PCI: pci_scan_slot() returns newly found devices
PCI: don't scan existing devices
...
Fix trivial append-only conflict in Documentation/feature-removal-schedule.txt
* 'iommu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (60 commits)
dma-debug: make memory range checks more consistent
dma-debug: warn of unmapping an invalid dma address
dma-debug: fix dma_debug_add_bus() definition for !CONFIG_DMA_API_DEBUG
dma-debug/x86: register pci bus for dma-debug leak detection
dma-debug: add a check dma memory leaks
dma-debug: add checks for kernel text and rodata
dma-debug: print stacktrace of mapping path on unmap error
dma-debug: Documentation update
dma-debug: x86 architecture bindings
dma-debug: add function to dump dma mappings
dma-debug: add checks for sync_single_sg_*
dma-debug: add checks for sync_single_range_*
dma-debug: add checks for sync_single_*
dma-debug: add checking for [alloc|free]_coherent
dma-debug: add add checking for map/unmap_sg
dma-debug: add checking for map/unmap_page/single
dma-debug: add core checking functions
dma-debug: add debugfs interface
dma-debug: add kernel command line parameters
dma-debug: add initialization code
...
Fix trivial conflicts due to whitespace changes in arch/x86/kernel/pci-nommu.c
cgroup documentation was moved to Documentation/cgroups/. There are some
places that still refer to Documentation/controllers/,
Documentation/cgroups.txt and Documentation/cpusets.txt. Fix those.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Reviewed-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Paul Menage <menage@google.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
smack: Add a new '-CIPSO' option to the network address label configuration
netlabel: Cleanup the Smack/NetLabel code to fix incoming TCP connections
lsm: Remove the socket_post_accept() hook
selinux: Remove the "compat_net" compatibility code
netlabel: Label incoming TCP connections correctly in SELinux
lsm: Relocate the IPv4 security_inet_conn_request() hooks
TOMOYO: Fix a typo.
smack: convert smack to standard linux lists
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (422 commits)
[ARM] 5435/1: fix compile warning in sanity_check_meminfo()
[ARM] 5434/1: ARM: OMAP: Fix mailbox compile for 24xx
[ARM] pxa: fix the bad assumption that PCMCIA sockets always start with 0
[ARM] pxa: fix Colibri PXA300 and PXA320 LCD backlight pins
imxfb: Fix TFT mode
i.MX21/27: remove ifdef CONFIG_FB_IMX
imxfb: add clock support
mxc: add arch_reset() function
clkdev: add possibility to get a clock based on the device name
i.MX1: remove fb support from mach-imx
[ARM] pxa: build arch/arm/plat-pxa/mfp.c only when PXA3xx or ARCH_MMP defined
Gemini: Add support for Teltonika RUT100
Gemini: gpiolib based GPIO support v2
MAINTAINERS: add myself as Gemini architecture maintainer
ARM: Add Gemini architecture v3
[ARM] OMAP: Fix compile for omap2_init_common_hw()
MAINTAINERS: Add myself as Faraday ARM core variant maintainer
ARM: Add support for FA526 v2
[ARM] acorn,ebsa110,footbridge,integrator,sa1100: Convert asm/io.h to linux/io.h
[ARM] collie: fix two minor formatting nits
...
The SELinux "compat_net" is marked as deprecated, the time has come to
finally remove it from the kernel. Further code simplifications are
likely in the future, but this patch was intended to be a simple,
straight-up removal of the compat_net code.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6: (81 commits)
[S390] remove duplicated #includes
[S390] cpumask: use mm_cpumask() wrapper
[S390] cpumask: Use accessors code.
[S390] cpumask: prepare for iterators to only go to nr_cpu_ids/nr_cpumask_bits.
[S390] cpumask: remove cpu_coregroup_map
[S390] fix clock comparator save area usage
[S390] Add hwcap flag for the etf3 enhancement facility
[S390] Ensure that ipl panic notifier is called late.
[S390] fix dfp elf hwcap/facility bit detection
[S390] smp: perform initial cpu reset before starting a cpu
[S390] smp: fix memory leak on __cpu_up
[S390] ipl: Improve checking logic and remove switch defaults.
[S390] s390dbf: Remove needless check for NULL pointer.
[S390] s390dbf: Remove redundant initilizations.
[S390] use kzfree()
[S390] BUG to BUG_ON changes
[S390] zfcpdump: Prevent zcore from beeing built as a kernel module.
[S390] Use csum_partial in checksum.h
[S390] cleanup lowcore.h
[S390] eliminate ipl_device from lowcore
...
This patch introduces the kernel parameter hvc_iucv_allow= that specifies
a comma-separated list of z/VM user IDs.
If specified, the z/VM IUCV hypervisor console device driver accepts IUCV
connections from listed z/VM user IDs only.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch combines Greg Bank's dprintk() work with the existing dynamic
printk patchset, we are now calling it 'dynamic debug'.
The new feature of this patchset is a richer /debugfs control file interface,
(an example output from my system is at the bottom), which allows fined grained
control over the the debug output. The output can be controlled by function,
file, module, format string, and line number.
for example, enabled all debug messages in module 'nf_conntrack':
echo -n 'module nf_conntrack +p' > /mnt/debugfs/dynamic_debug/control
to disable them:
echo -n 'module nf_conntrack -p' > /mnt/debugfs/dynamic_debug/control
A further explanation can be found in the documentation patch.
Signed-off-by: Greg Banks <gnb@sgi.com>
Signed-off-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch extends command line option "i2c_bus=bus_id,clkrate" so that
it allow to register additional I2C busses that are not registered with
omap_register_i2c_bus from board initialization code.
Purpose of this is to register additional board busses which are routed
to external connectors only without any on board I2C devices.
Cc: linux-i2c@vger.kernel.org
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds a new command line option "i2c_bus=bus_id,clkrate" into
I2C bus registration helper. Purpose of the option is to override the
default board specific bus speed which is supplied by the
omap_register_i2c_bus.
The default bus speed is typically set to speed of slowest I2C chip on the
bus and overriding allow to use some experimental configurations or updated
chip versions without any kernel modifications.
Cc: linux-i2c@vger.kernel.org
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch allows memory resources to be assigned with a specified
alignment at boot-time or run-time. The patch is useful when we use PCI
pass-through, because page-aligned memory resources are required to
securely share PCI resources with guest drivers.
If you want to assign the resource at boot time, please set
"pci=resource_alignment=" boot parameter.
This is format of "pci=resource_alignment=" boot parameter:
[<order of align>@][<domain>:]<bus>:<slot>.<func>[; ...]
Specifies alignment and device to reassign
aligned memory resources.
If <order of align> is not specified, PAGE_SIZE is
used as alignment.
PCI-PCI bridge can be specified, if resource
windows need to be expanded.
This is example:
pci=resource_alignment=20@07:00.0;18@0f:00.0;00:1d.7
If you want to assign the resource at run-time, please set
"/sys/bus/pci/resource_alignment" file, and hot-remove the device and
hot-add the device. For this purpose, fakephp or PCI hotplug interfaces
can be used.
The format of "/sys/bus/pci/resource_alignment" file is the same with
boot parameter. You can use "," instead of ";".
For example:
# cd /sys/bus/pci
# echo -n 20@12:00.0 > resource_alignment
# echo 1 > devices/0000:12:00.0/remove
# echo 1 > rescan
Reviewed-by: Alex Chiang <achiang@hp.com>
Reviewed-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Yuji Shimada <shimada-yxb@necst.nec.co.jp>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Document the "pci=earlydump" argument. This currently only works on x86.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
from early boot tracing view, trace_buf_size parameter is important.
it should be documented.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
LKML-Reference: <20090310135200.A48B.A69D9226@jp.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
While trying to debug why my Atom netbook is falling over booting
rawhide debug-enabled kernels, I stumbled across the fact that we've
been enabling object debugging by default. However, once you default it
to on, you've got no way to turn it back off again at runtime.
Add a boolean toggle to turn it off. I would just make it an int
module_param, however people may already expect the boolean enable
behaviour, so just add an analogue for disabling.
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: enable DMAR by default
xen: disable interrupts early, as start_kernel expects
gpu/drm, x86, PAT: io_mapping_create_wc and resource_size_t
gpu/drm, x86, PAT: Handle io_mapping_create_wc() errors in a clean way
x86, Voyager: fix compile by lifting the degeneracy of phys_cpu_present_map
x86, doc: fix references to Documentation/x86/i386/boot.txt
Documentation/kernel-parameters.txt
- ide=nodma is no longer valid.
drivers/ide/Kconfig
- The module is ide-core.ko not ide.
drivers/ide/ide.c
- It took me a while to figure out what the arguments %d.%d:%d to nodma
module parameter ment, so I added a comment to each.
- Added a comment to each of the sscanf lines.
- There is a bug, if j is 0 it would previously clear all the other bits
except the current device, changed in three different places.
mask &= (1 << i) should be mask &= ~(1 << i).
Signed-off-by: David Fries <david@fries.net>
[bart: s/disk/device/ in ide.c, beautify patch description]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Impact: Documentation fix
The amazing dancing boot.txt file has jumped places again. It should
never have been in Documentation/x86/i386, since it never was
32-bit-specific, but it unfortunately ended up there for a while.
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Add missing parameter value to list of available values
for acpi=<value>.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
IMA provides hardware (TPM) based measurement and attestation for
file measurements. As the Trusted Computing (TPM) model requires,
IMA measures all files before they are accessed in any way (on the
integrity_bprm_check, integrity_path_check and integrity_file_mmap
hooks), and commits the measurements to the TPM. Once added to the
TPM, measurements can not be removed.
In addition, IMA maintains a list of these file measurements, which
can be used to validate the aggregate value stored in the TPM. The
TPM can sign these measurements, and thus the system can prove, to
itself and to a third party, the system's integrity in a way that
cannot be circumvented by malicious or compromised software.
- alloc ima_template_entry before calling ima_store_template()
- log ima_add_boot_aggregate() failure
- removed unused IMA_TEMPLATE_NAME_LEN
- replaced hard coded string length with #define name
Signed-off-by: Mimi Zohar <zohar@us.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
This patch replaces the generic integrity hooks, for which IMA registered
itself, with IMA integrity hooks in the appropriate places directly
in the fs directory.
Signed-off-by: Mimi Zohar <zohar@us.ibm.com>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
Due to recurring issues with DMAR support on certain platforms.
There's a number of filesystem corruption incidents reported:
https://bugzilla.redhat.com/show_bug.cgi?id=479996http://bugzilla.kernel.org/show_bug.cgi?id=12578
Provide a Kconfig option to change whether it is enabled by
default.
If disabled, it can still be reenabled by passing intel_iommu=on to the
kernel. Keep the .config option off by default.
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-By: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Remove removed OSS kernel parameters from kernel-parameters.txt
Remove the kernel parameters from the OSS drivers of the chips
es1371 (removed 10-2007/2.6.24) and
cs4232 (removed 02-2008/2.6.25) from the kernel parameters documentation.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] update documentation for hvc_iucv kernel parameter.
[S390] hvc_iucv: Special handling of IUCV HVC devices
[S390] hvc_iucv: Refactor console and device initialization
[S390] hvc_iucv: Update function documentation
[S390] hvc_iucv: Limit rate of outgoing IUCV messages
[S390] hvc_iucv: Change IUCV term id and use one device as default
[S390] Use unsigned long long for u64 on 64bit.
[S390] qdio: fix broken pointer in case of CONFIG_DEBUG_FS is disabled
[S390] vdso: compile fix
[S390] remove code for oldselect system call
[S390] types: add/fix types.h include in header files
[S390] dasd: add device attribute to disable blocking on lost paths
[S390] dasd: send change uevents for dasd block devices
[S390] tape block: fix dependencies
[S390] asm-s390/posix_types.h: drop __USE_ALL usage
[S390] gettimeofday.S: removed duplicated #includes
[S390] ptrace: no extern declarations for userspace
On some boxes there exist both RSDT and XSDT table. But unfortunately
sometimes there exists the following error when XSDT table is used:
a. 32/64X address mismatch
b. The 32/64X FACS address mismatch
In such case the boot option of "acpi=rsdt" is provided so that
RSDT is tried instead of XSDT table when the system can't work well.
http://bugzilla.kernel.org/show_bug.cgi?id=8246
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
cc:Thomas Renninger <trenn@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Config and control variable for mem+swap controller.
This patch adds CONFIG_CGROUP_MEM_RES_CTLR_SWAP
(memory resource controller swap extension.)
For accounting swap, it's obvious that we have to use additional memory to
remember "who uses swap". This adds more overhead. So, it's better to
offer "choice" to users. This patch adds 2 choices.
This patch adds 2 parameters to enable swap extension or not.
- CONFIG
- boot option
Reviewed-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Cc: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (98 commits)
PCI PM: Put PM callbacks in the order of execution
PCI PM: Run default PM callbacks for all devices using new framework
PCI PM: Register power state of devices during initialization
PCI PM: Call pci_fixup_device from legacy routines
PCI PM: Rearrange code in pci-driver.c
PCI PM: Avoid touching devices behind bridges in unknown state
PCI PM: Move pci_has_legacy_pm_support
PCI PM: Power-manage devices without drivers during suspend-resume
PCI PM: Add suspend counterpart of pci_reenable_device
PCI PM: Fix poweroff and restore callbacks
PCI: Use msleep instead of cpu_relax during ASPM link retraining
PCI: PCIe portdrv: Add kerneldoc comments to remining core funtions
PCI: PCIe portdrv: Rearrange code so that related things are together
PCI: PCIe portdrv: Fix suspend and resume of PCI Express port services
PCI: PCIe portdrv: Add kerneldoc comments to some core functions
x86/PCI: Do not use interrupt links for devices using MSI-X
net: sfc: Use pci_clear_master() to disable bus mastering
PCI: Add pci_clear_master() as opposite of pci_set_master()
PCI hotplug: remove redundant test in cpq hotplug
PCI: pciehp: cleanup register and field definitions
...
Device drivers that use pci_request_regions() (and similar APIs) have a
reasonable expectation that they are the only ones accessing their device.
As part of the e1000e hunt, we were afraid that some userland (X or some
bootsplash stuff) was mapping the MMIO region that the driver thought it
had exclusively via /dev/mem or via various sysfs resource mappings.
This patch adds the option for device drivers to cause their reserved
regions to the "banned from /dev/mem use" list, so now both kernel memory
and device-exclusive MMIO regions are banned.
NOTE: This is only active when CONFIG_STRICT_DEVMEM is set.
In addition to the config option, a kernel parameter iomem=relaxed is
provided for the cases where developers want to diagnose, in the field,
drivers issues from userspace.
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch (as1190) makes usb-storage's "quirks=" module parameter
writable, so that users can add entries for their devices at runtime
with no need to reboot or reload usb-storage.
New codes are added for the SANE_SENSE, CAPACITY_HEURISTICS, and
CAPACITY_OK flags.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1163b) adds a "quirks=" module parameter to usb-storage.
This will allow people to make short-term changes to their
unusual_devs list without rebuilding the entire driver. Testing will
become much easier, and less-sophisticated users will be able to
access their buggy devices after a simple config-file change instead
of having to wait for a new kernel release.
The patch also adds a documentation entry for usb-storage's
"delay_use" parameter, which has been around for years but but was
never listed among the kernel parameters.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Introduce a new kernel parameter `coredump_filter'. Setting a value to
this parameter causes the default bitmask of coredump_filter to be
changed.
It is useful for users to change coredump_filter settings for the whole
system at boot time. Without this parameter, users have to change
coredump_filter settings for each /proc/<pid>/ in an initializing script.
Signed-off-by: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Cc: Roland McGrath <roland@redhat.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reformat text to (mostly) stay within 80 columns of text.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add some (more) early_param boot options to kernel-parameters.txt.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update several Documentation/ files and a few sub-dir files (only one
change in each) to reflect changed header files locations.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
kmemtrace provides tracing for slab allocator functions, such as kmalloc,
kfree, kmem_cache_alloc, kmem_cache_free etc.. Collected data is then fed
to the userspace application in order to analyse allocation hotspots,
internal fragmentation and so on, making it possible to see how well an
allocator performs, as well as debug and profile kernel code.
Signed-off-by: Eduard - Gabriel Munteanu <eduard.munteanu@linux360.ro>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
* 'tracing-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (241 commits)
sched, trace: update trace_sched_wakeup()
tracing/ftrace: don't trace on early stage of a secondary cpu boot, v3
Revert "x86: disable X86_PTRACE_BTS"
ring-buffer: prevent false positive warning
ring-buffer: fix dangling commit race
ftrace: enable format arguments checking
x86, bts: memory accounting
x86, bts: add fork and exit handling
ftrace: introduce tracing_reset_online_cpus() helper
tracing: fix warnings in kernel/trace/trace_sched_switch.c
tracing: fix warning in kernel/trace/trace.c
tracing/ring-buffer: remove unused ring_buffer size
trace: fix task state printout
ftrace: add not to regex on filtering functions
trace: better use of stack_trace_enabled for boot up code
trace: add a way to enable or disable the stack tracer
x86: entry_64 - introduce FTRACE_ frame macro v2
tracing/ftrace: add the printk-msg-only option
tracing/ftrace: use preempt_enable_no_resched_notrace in ring_buffer_time_stamp()
x86, bts: correctly report invalid bts records
...
Fixed up trivial conflict in scripts/recordmcount.pl due to SH bits
being already partly merged by the SH merge.
* 'x86-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (246 commits)
x86: traps.c replace #if CONFIG_X86_32 with #ifdef CONFIG_X86_32
x86: PAT: fix address types in track_pfn_vma_new()
x86: prioritize the FPU traps for the error code
x86: PAT: pfnmap documentation update changes
x86: PAT: move track untrack pfnmap stubs to asm-generic
x86: PAT: remove follow_pfnmap_pte in favor of follow_phys
x86: PAT: modify follow_phys to return phys_addr prot and return value
x86: PAT: clarify is_linear_pfn_mapping() interface
x86: ia32_signal: remove unnecessary declaration
x86: common.c boot_cpu_stack and boot_exception_stacks should be static
x86: fix intel x86_64 llc_shared_map/cpu_llc_id anomolies
x86: fix warning in arch/x86/kernel/microcode_amd.c
x86: ia32.h: remove unused struct sigfram32 and rt_sigframe32
x86: asm-offset_64: use rt_sigframe_ia32
x86: sigframe.h: include headers for dependency
x86: traps.c declare functions before they get used
x86: PAT: update documentation to cover pgprot and remap_pfn related changes - v3
x86: PAT: add pgprot_writecombine() interface for drivers - v3
x86: PAT: change pgprot_noncached to uc_minus instead of strong uc - v3
x86: PAT: implement track/untrack of pfnmap regions for x86 - v3
...
Introduce a topology=[on|off] kernel parameter which allows to switch
cpu topology on/off. Default will be off, since it looks like that for
some workloards this doesn't behave very well (on s390).
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Spell out "wrt". I suspect plenty of people won't know
what that means.
Fix a '}' that should be a ']'.
Reformat long lines into shorter lines.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Len Brown <len.brown@intel.com>
On some machines it may be necessary to disable the saving/restoring
of the ACPI NVS memory region during hibernation/resume. For this
purpose, introduce new ACPI kernel command line option
acpi_sleep=s4_nonvs.
Based on a patch by Zhang Rui.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Nigel Cunningham <nigel@tuxonice.net>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_early_init() was changed to over-write the cmdline param,
making it really inconvenient to set debug flags at boot-time.
Also,
This sets the default level to "info", which is what all the ACPI
drivers use. So to enable messages from drivers, you only have to
supply the "layer" (a.k.a. "component"). For non-"info" ACPI core
and ACPI interpreter messages, you have to supply both level and
layer masks, as before.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Impact: enhancement to stack tracer
The stack tracer currently is either on when configured in or
off when it is not. It can not be disabled when it is configured on.
(besides disabling the function tracer that it uses)
This patch adds a way to enable or disable the stack tracer at
run time. It defaults off on bootup, but a kernel parameter 'stacktrace'
has been added to enable it on bootup.
A new sysctl has been added "kernel.stack_tracer_enabled" to let
the user enable or disable the stack tracer at run time.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Conflicts:
fs/nfsd/nfs4recover.c
Manually fixed above to use new creds API functions, e.g.
nfs4_save_creds().
Signed-off-by: James Morris <jmorris@namei.org>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: more general identifier for Phoenix BIOS
AMD IOMMU: check for next_bit also in unmapped area
AMD IOMMU: fix fullflush comparison length
AMD IOMMU: enable device isolation per default
AMD IOMMU: add parameter to disable device isolation
x86, PEBS/DS: fix code flow in ds_request()
x86: add rdtsc barrier to TSC sync check
xen: fix scrub_page()
x86: fix es7000 compiling
x86, bts: fix unlock problem in ds.c
x86, voyager: fix smp generic helper voyager breakage
x86: move iomap.h to the new include location
Add "min_addr" documentation.
For "max_addr", add nn before [KMG] since a number is needed and this
is consistent with other uses of [KMG].
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Impact: makes device isolation the default for AMD IOMMU
Some device drivers showed double-free bugs of DMA memory while testing
them with AMD IOMMU. If all devices share the same protection domain
this can lead to data corruption and data loss. Prevent this by putting
each device into its own protection domain per default.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Create Documentation/blockdev/ sub-directory and populate it.
Populate the Documentation/serial/ sub-directory.
Move MSI-HOWTO.txt to Documentation/PCI/.
Move ioctl-number.txt to Documentation/ioctl/.
Update all relevant 00-INDEX files.
Update all relevant Kconfig files and source files.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Conflicts:
security/keys/internal.h
security/keys/process_keys.c
security/keys/request_key.c
Fixed conflicts above by using the non 'tsk' versions.
Signed-off-by: James Morris <jmorris@namei.org>
If an ACPI graphics device supports backlight brightness functions (cmp. with
latest ACPI spec Appendix B), let the ACPI video driver control backlight and
switch backlight control off in vendor specific ACPI drivers (asus_acpi,
thinkpad_acpi, eeepc, fujitsu_laptop, msi_laptop, sony_laptop, acer-wmi).
Currently it is possible to load above drivers and let both poke on the
brightness HW registers, the video and vendor specific ACPI drivers -> bad.
This patch provides the basic support to check for BIOS capabilities before
driver loading time. Driver specific modifications are in separate follow up
patches.
"acpi_backlight=vendor"
Prever vendor driver over ACPI driver for backlight.
"acpi_backlight=video" (default)
Prever ACPI driver over vendor driver for backlight.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Linus Torvalds