Register hot-added memory to iomem_resource. With this, /proc/iomem can
show hot-added memory.
Note: kdump uses /proc/iomem to catch memory range when it is installed.
So, kdump should be re-installed after /proc/iomem change.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add node-hot-add support to add_memory().
node hotadd uses this sequence.
1. allocate pgdat.
2. refresh NODE_DATA()
3. call free_area_init_node() to initialize
4. create sysfs entry
5. add memory (old add_memory())
6. set node online
7. run kswapd for new node.
(8). update zonelist after pages are onlined. (This is already merged in -mm
due to update phase is difference.)
Note:
To make common function as much as possible,
there is 2 changes from v2.
- The old add_memory(), which is defiend by each archs,
is renamed to arch_add_memory(). New add_memory becomes
caller of arch dependent function as a common code.
- This patch changes add_memory()'s interface
From: add_memory(start, end)
TO : add_memory(nid, start, end).
It was cause of similar code that finding node id from
physical address is inside of old add_memory() on each arch.
In addition, acpi memory hotplug driver can find node id easier.
In v2, it must walk DSDT'S _CRS by matching physical address to
get the handle of its memory device, then get _PXM and node id.
Because input is just physical address.
However, in v3, the acpi driver can use handle to get _PXM and node id
for the new memory device. It can pass just node id to add_memory().
Fix interface of arch_add_memory() is in next patche.
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When node is hot-added, kswapd for the node should start. This export kswapd
start function as kswapd_run() to use at add_memory().
[akpm@osdl.org: daemonize() isn't needed when using the kthread API]
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Refresh NODE_DATA() for generic archs. In this case, NODE_DATA(nid) ==
node_data[nid]. node_data[] is array of address of pgdat. So, refresh is
quite simple.
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
For node hotplug, basically we have to allocate new pgdat. But, there are
several types of implementations of pgdat.
1. Allocate only pgdat.
This style allocate only pgdat area.
And its address is recorded in node_data[].
It is most popular style.
2. Static array of pgdat
In this case, all of pgdats are static array.
Some archs use this style.
3. Allocate not only pgdat, but also per node data.
To increase performance, each node has copy of some data as
a per node data. So, this area must be allocated too.
Ia64 is this style. Ia64 has the copies of node_data[] array
on each per node data to increase performance.
In this series of patches, treat (1) as generic arch.
generic archs can use generic function. (2) and (3) should have
its own if necessary.
This patch defines pgdat allocator.
Updating NODE_DATA() macro function is in other patch.
Signed-off-by: Yasonori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is to find node id from acpi's handle of memory_device in DSDT. _PXM for
the new node can be found by acpi_get_pxm() by using new memory's handle. So,
node id can be found by pxm_to_nid_map[].
This patch becomes simpler than v2 of node hot-add patch.
Because old add_memory() function doesn't have node id parameter.
So, kernel must find its handle by physical address via DSDT again.
But, v3 just give node id to add_memory() now.
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change the name of old add_memory() to arch_add_memory. And use node id to
get pgdat for the node at NODE_DATA().
Note: Powerpc's old add_memory() is defined as __devinit. However,
add_memory() is usually called only after bootup.
I suppose it may be redundant. But, I'm not well known about powerpc.
So, I keep it. (But, __meminit is better at least.)
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When acpi_memory_device_init() is called at boottime to register struct
memory acpi_memory_device, acpi_bus_add() are called via
acpi_driver_attach().
But it also calls ops->start() function. It is called even if the memory
blocks are initialized at early boottime. In this case add_memory() return
-EEXIST, and the memory blocks becomes INVALID state even if it is normal.
This is patch to avoid calling add_memory() for already available memory.
[akpm@osdl.org: coding cleanups]
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: "Brown, Len" <len.brown@intel.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is a patch to call add_memroy() when notify reaches for new node's add
event.
When new node is added, notify of ACPI reaches container device which means
the node.
Container device driver calls acpi_bus_scan() to find and add belonging
devices (which means cpu, memory and so on). Its function calls add and
start function of belonging devices's driver.
Howevever, current memory hotplug driver just register add function to
create sysfs file for its memory. But, acpi_memory_enable_device() is not
called because it is considered just the case that notify reaches memory
device directly. So, if notify reaches container device nothing can call
add_memory().
This is a patch to create start function which calls add_memory().
add_memory() can be called by this when notify reaches container device.
[akpm@osdl.org: coding cleanups]
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: "Brown, Len" <len.brown@intel.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Current acpi memory hotplug just looks into the first entry of resources in
_CRS. But, _CRS can contain plural resources. So, if _CRS contains plural
resoureces, acpi memory hot add cannot add all memory.
With this patch, acpi memory hotplug can deal with Memory Device, whose
_CRS contains plural resources.
Tested on ia64 memory hotplug test envrionment (not emulation, uses alpha
version firmware which supports dynamic reconfiguration of NUMA.)
Note: Microsoft's Windows Server 2003 requires big (>4G)resoureces to be
divided into small (<4G) resources. looks crazy, but not invalid.
(See http://www.microsoft.com/whdc/system/pnppwr/hotadd/hotaddmem.mspx)
For this reason, a firmware vendor who supports Windows writes plural
resources in a _CRS even if they are contiguous.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
CONFIG_PM_TRACES scrogs your RTC. Mark it as experimental, and defaulting to
`off'.
Also beef up the help message a bit.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix function definitions to be ANSI-compliant:
lib/zlib_inflate/inffast.c:68:1: warning: non-ANSI definition of function 'inflate_fast'
lib/zlib_inflate/inftrees.c:33:1: warning: non-ANSI definition of function 'zlib_inflate_table'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
kernel/acct.c:579:19: warning: non-ANSI function declaration of function 'acct_process'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Builds on ARM report link problems with common configurations like
statically linked NFS (for nfsroot). The symptom is that __init
section code references __exit section code; that won't work since
the exit sections are discarded (since they can never be called).
The best fix for these particular cases would be an "__init_or_exit"
section annotation.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It should be done before calling class_device_unregister() because
it will destroy the device and free memory if there are no other
references to the device.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This reverts commit e5c44fd88c.
Thanks to Daniel Ritz and Michal Piotrowski for noticing the problem.
Daniel says:
"[The] reason is a recent change that made modules always shows as
module.mod. it breaks modprobe and probably many scripts..besides
lsmod looking horrible
stuff like this in modprobe.conf:
install pcmcia_core /sbin/modprobe --ignore-install pcmcia_core; /sbin/modprobe pcmcia
makes modprobe fork/exec endlessly calling itself...until oom
interrupts it"
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2: (56 commits)
[PATCH] fs/ocfs2/dlm/: cleanups
ocfs2: fix compiler warnings in dlm_convert_lock_handler()
ocfs2: dlm_print_one_mle() needs to be defined
ocfs2: remove whitespace in dlmunlock.c
ocfs2: move dlm work to a private work queue
ocfs2: fix incorrect error returns
ocfs2: tune down some noisy messages during dlm recovery
ocfs2: display message before waiting for recovery to complete
ocfs2: mlog in dlm_convert_lock_handler() should be ML_ERROR
ocfs2: retry operations when a lock is marked in recovery
ocfs2: use cond_resched() in dlm_thread()
ocfs2: use GFP_NOFS in some dlm operations
ocfs2: wait for recovery when starting lock mastery
ocfs2: continue recovery when a dead node is encountered
ocfs2: remove unneccesary spin_unlock() in dlm_remaster_locks()
ocfs2: dlm_remaster_locks() should never exit without completing
ocfs2: special case recovery lock in dlmlock_remote()
ocfs2: pending mastery asserts and migrations should block each other
ocfs2: temporarily disable automatic lock migration
ocfs2: do not unconditionally purge the lockres in dlmlock_remote()
...
Patch from Ben Dooks
Update the list of supported devices, and remove the
changelog. Add SMDK2413 information.--
Signed-off-by: Ben Dooks <ben-linux@fluff.org>Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch #if 0's the no longer used dlm_dump_lock_resources().
Since this makes dlmdebug.h empty, this patch also removes this header.
Additionally, the needlessly global dlm_is_node_recovered() is made
static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
The work that is done can block for long periods of time and so is not
appropriate for keventd.
Signed-off-by: Kurt Hackel <kurt.hackel@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Before checking for a nonexistent lock, make sure the lockres is not marked
RECOVERING. The caller will just retry and the state should be fixed up when
recovery completes.
Signed-off-by: Kurt Hackel <kurt.hackel@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
We cannot restart recovery. Once we begin to recover a node, keep the state
of the recovery intact and follow through, regardless of any other node
deaths that may occur.
Signed-off-by: Kurt Hackel <kurt.hackel@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
If the previous master of the recovery lock dies, let calc_usage take it
down completely and let the caller completely redo the dlmlock() call.
Otherwise, there will never be an opportunity to re-master the lockres and
recovery wont be able to progress.
Signed-off-by: Kurt Hackel <kurt.hackel@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Use the existing structure for blocking migrations when ASTs are pending to
achieve the same result. If we can catch the assert before it goes on the
wire, just cancel it and let the migration continue.
Signed-off-by: Kurt Hackel <kurt.hackel@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Now we never change the owner of a lock resource until unmount or node
death. This will be re-enabled once some issues in the algorithm used have
been resolved.
Signed-off-by: Kurt Hackel <kurt.hackel@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
In dlmlock_remote(), do not call purge_lockres until the lock resource
actually changes. otherwise, the mastery info on the lockres will go away
underneath the caller.
Signed-off-by: Kurt Hackel <kurt.hackel@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
When mastering non-recovery lock resources, additional time was frequently
needed to allow the disk heartbeat to catch up with the network timeout. the
recovery lock resource is time critical and avoids this path.
Signed-off-by: Kurt Hackel <kurt.hackel@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Recovery will spin in dlm_pre_master_reco_lockres if we do not ignore
timed-out network responses from dead nodes.
Signed-off-by: Kurt Hackel <kurt.hackel@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Change behavior of dlm_restart_lock_mastery() when a node goes down. Dump
all responses that have been collected and start over.
Signed-off-by: Kurt Hackel <kurt.hackel@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
This is an error on the sending side, so gracefully error out on the
receiving end.
Signed-off-by: Kurt Hackel <kurt.hackel@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Immediately purge a lockress that the local node is not the master of.
Signed-off-by: Kurt Hackel <kurt.hackel@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
