The current code checks for both DATA_END and DATA_BLK_END bits in
MCI_STATUS register and ends a request only if both are set at a time.
The hardware doesn't always set DATA_BLK_END when DATA_END is set.
But DATA_END status itself is sufficient condition from hardware that
data transfer is done and hence, check for only DATA_END interrupt in
software to end a request.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
The current code for PIO doesn't transfer whole data when data size
is not in multiple of 4 bytes. The last few bytes are not written to
the card resulting in no DATAEND interrupt from SDCC. This patch
allows data transfer for non-aligned data size in PIO mode.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
SDCC uses an asynchronous FIFOs for data synchronization (one for TX
and one for RX). For any error when DPSM (Data path state machine) is
involved the transfer is terminated with the remaining data stuck inside
FIFOs. Reset the controller in case of data errors to ensure that
any left over data in FIFOs is flushed out and DPSM is in good state.
The following problems are observed without this reset functionality -
1. After the card is removed in an unsafe way (removed when there
is an on going data transfer), the card will not be detected upon
its next insertion. This is because the controller wouldn't respond
to few initialization commands.
2. When an error occurs for a data transfer in non-DMA mode, sometimes
we get spurious PIO interrupt after the request is processed.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Enable prog done interrupt for stop command(CMD12) that is sent
after a multi-block write(CMD25). The PROG_DONE bit is set when
the card has finished its programming and is ready for next data.
After every write request the card will be polled for ready status
using CMD13. For a multi-block write(CMD25) before sending CMD13,
stop command (CMD12) will be sent. If we enable prog done interrupt
for CMD12, then CMD13 polling can be avoided. The prog done interrupt
means that the card is done with its programming and is ready for
next request.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
In the context of request processing thread, data mover lock is
acquired after the host lock. In another context, in the completion
handler of data mover the locks are acquired in the reverse order,
resulting in possible circular lock dependency warning. Hence,
schedule a tasklet to process the dma completion so as to avoid
nested locks.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Initial framebuffer components. Add board-trout-panel.c
as well as platform parts to enable the framebuffer. This
code comes directly from Google's tree.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
CLK_MINMAX is used to denote clocks that have a wide variation
in possible frequencies. This handling just sets the min and
max values to the same value.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
This clock is used in the framebuffer driver as mddi_clk.
This just changes the name to match that. This also
mirrors a change in Google tree.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
This adds in the CLK_MINMAX flag to the pmdh_clk since it's actual
a min/max clock instead of a single frequency clock.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
trout has gpiolib support and interrupt support, but was
missing the gpio_to_irq function. This adds that functions
which should allow proper translation.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Change msm_iommu_map to use GFP_ATOMIC instead of
GFP_KERNEL due to the fact that the call occurs within
a spinlock-protected region.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
IS_ERR() already implies unlikely(), so it can be omitted here.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David Brown <davidb@codeaurora.org>
Remove some unneeded assignments and messages, restructure
a failure path in iova_to_phys, and make __flush_iotlb
return int in preparation for adding IOMMU clock control.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Add support for allowing IOMMU memory transactions to be
cache coherent, eliminating the need for software cache
management in certain situations. This can lead to
improvements in performance and power usage, assuming the
multimedia core's access pattern exhibits spatial locality
and that its working set fits into the cache.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Add the register field definitions and memory attribute
definitions that will be needed to support IOMMU
transactions with cache-coherent memory access.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Make the IOMMU driver select the IOMMU API in the kernel
configuration.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
An IOMMU device can only be attached to one IOMMU domain at
any given time. Check whether the device is already
attached to a domain before allowing it to be attached to
another domain. If so, return busy.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Add a Kconfig item to allow the IOMMU page tables to be
coherent in the L2 cache. This generally reduces IOTLB miss
latencies and has been shown to improve multimedia
performance.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Don't flush the page tables on an IOMMU domain if there are
no IOMMU devices attached to the domain. The act of
attaching to the domain will cause an implicit flush of
those areas if the page tables are configured to not be L2
cacheable.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Mark the init and exit functions as __init and __exit where
appropriate.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Add the platform data and resources needed for the second
2D graphics core's IOMMU.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Based on recommendations from chip designers,
optimize the Machine ID to translation context
mappings for the first 2D core's IOMMU. Remove the
"gfx2d0_texv3_smmu" context, as it is no longer needed
under the new mapping scheme.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Based on recommendations from chip designers,
optimize the Machine ID to translation context
mappings for the 3D core's IOMMU. Remove the
the "gfx3d_smmu" context device, as it is no longer
needed under the new mapping scheme.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
[dwalker@codeaurora.org: updated commit text]
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Rename all the IOMMU platform devices so that the names are
more consistent with the rest of the codebase.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Add register addresses and IRQ numbers for the IOMMU used
for the second 2D graphics core.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
On msm8x60, the MID field on the AXI connection to the
IOMMU can be up to five bits wide. Thus, allow the IOMMU
context platform data to map up to 32 MIDs.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Beginning with the MSM8x60, the hardware block responsible for gpio
support changes. Provide gpiolib support for the new v2 architecture.
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Pavan Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Gregory Bean <gbean@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
This is required for modules to use ioremap()
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Define VMALLOC_END as an unsigned long to match expected type.
Eliminates a warning:
arch/arm/mm/init.c: In function 'mem_init':
arch/arm/mm/init.c:606: warning: format '%08lx' expects type
'long unsigned int', but argument 12 has type 'unsigned int'
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Put some variables inside of the same ifdef as the code that uses
them.
arch/arm/mach-msm/smd_debug.c: In function 'smsm_print_sleep_info':
arch/arm/mach-msm/smd_debug.c:274: warning: unused variable 'int_info'
arch/arm/mach-msm/smd_debug.c:273: warning: unused variable 'gpio'
Signed-off-by: David Brown <davidb@codeaurora.org>
[dwalker@codeaurora.org: changed the commit text a little.]
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Eliminate some unreferenced variables.
arch/arm/mach-msm/sirc.c:43: warning: 'save_type' defined but not used
arch/arm/mach-msm/sirc.c:44: warning: 'save_polarity' defined but not used
Signed-off-by: David Brown <davidb@codeaurora.org>
[dwalker@codeaurora.org: changed the commit text a little.]
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
The MSM smd driver logs numerous messages during startup that are
useful for debug purposes. Change some of these to pr_debug() to
match their purpose, and remove others that aren't really useful.
Cc: Brian Swetland <swetland@google.com>
Cc: Arve Hjønnevåg <arve@android.com>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
* 'next-spi' of git://git.secretlab.ca/git/linux-2.6:
spi/pl022: fix erroneous platform data in U300
spi: fixed odd static string conventions in core code
spi/bfin_spi: only request GPIO on first load
spi/bfin_spi: handle error/status changes after data interrupts
spi: enable spi_board_info to be registered after spi_master
This fixes an erroneous use of LSB first in the U300 machine, the
PL022 used in U300 is a standard ARM core that doesn't support this
bit so it should never have been set.
Cc: Kevin Wells <wellsk40@gmail.com>OA
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
We were forgetting to set up proper return value in success path causing
ir_getkeycode() to fail intermittently:
drivers/media/IR/ir-keytable.c: In function 'ir_getkeycode':
drivers/media/IR/ir-keytable.c:363: warning: 'retval' may be used
uninitialized in this function
Reported-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c-i801: Add PCI idents for Patsburg 'IDF' SMBus controllers
i2c-i801: Handle multiple instances instead of keeping global state
i2c-i801: Add Intel Patsburg device ID
i2c: Drop unused I2C_CLASS_TV flags
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: appletouch - remove extra KERN_DEBUG use from dprintk
Input: bu21013_ts - fix null dereference in error handling
Input: ad7879 - prevent invalid finger data reports
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (70 commits)
[SCSI] pmcraid: add support for set timestamp command and other fixes
[SCSI] pmcraid: remove duplicate struct member
[SCSI] qla4xxx: Fix cmd check in qla4xxx_cmd_wait
[SCSI] megaraid_sas: Version and documentation update
[SCSI] megaraid_sas: Add three times Online controller reset
[SCSI] megaraid_sas: Add input parameter for max_sectors
[SCSI] megaraid_sas: support devices update flag
[SCSI] libosd: write/read_sg_kern API
[SCSI] libosd: Support for scatter gather write/read commands
[SCSI] libosd: Free resources in reverse order of allocation
[SCSI] libosd: Fix bug in attr_page handling
[SCSI] lpfc 8.3.18: Update lpfc driver version to 8.3.18
[SCSI] lpfc 8.3.18: Add new WQE support
[SCSI] lpfc 8.3.18: Fix critical errors
[SCSI] lpfc 8.3.18: Adapter Shutdown and Unregistration cleanup
[SCSI] lpfc 8.3.18: Add logic to detect last devloss timeout
[SCSI] lpfc 8.3.18: Add support of received ELS commands
[SCSI] lpfc 8.3.18: FC/FCoE Discovery fixes
[SCSI] ipr: add definitions for a new adapter
[SCSI] bfa: fix comments for c files
...
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
genirq: Fix up irq_node() for irq_data changes.
genirq: Add single IRQ reservation helper
genirq: Warn if enable_irq is called before irq is set up
* 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
semaphore: Remove mutex emulation
staging: Final semaphore cleanup
jbd2: Convert jbd2_slab_create_sem to mutex
hpfs: Convert sbi->hpfs_creation_de to mutex
Fix up trivial change/delete conflicts with deleted 'dream' drivers
(drivers/staging/dream/camera/{mt9d112.c,mt9p012_fox.c,mt9t013.c,s5k3e2fx.c})
These are the extra 'Integrated Device Function' SMBus controllers found
on the Patsburg chipset. Mention the absence of slave mode support.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
It's poor form to keep driver state in global variables rather than
per-instance. It never really mattered in practice when there was only
one controller on the chipset, but the latest chipsets do have more
than one controller, so now we care.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for the Intel Patsburg PCH SMBus Controller.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This one was only used for a nasty hack in nfsd, which has recently
been removed.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The caller allocated it, the caller should free it.
The only issue so far is that we could change the flp pointer even on an
error return if the fl_change callback failed. But we can simply move
the flp assignment after the fl_change invocation, as the callers don't
care about the flp return value if the setlease call failed.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
