Without this udelay(1) PCI idsel does not work correctly on the
"singleboard" (T-Mobile Surfbox) for the MiniPCI device. The result is
that PCI configuration fails and the MiniPCI card is not detected
correctly. Instead of
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [mem 0x40000000-0x4fffffff]
pci_bus 0000:00: root bus resource [io 0x1000-0xffff]
pci 0000:00:03.0: BAR 0: assigned [mem 0x40000000-0x4000ffff]
pci 0000:00:00.0: BAR 0: assigned [mem 0x40010000-0x40010fff]
pci 0000:00:00.1: BAR 0: assigned [mem 0x40011000-0x40011fff]
We see only the CardBus device:
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [mem 0x40000000-0x4fffffff]
pci_bus 0000:00: root bus resource [io 0x1000-0xffff]
pci 0000:00:00.0: BAR 0: assigned [mem 0x40000000-0x40000fff]
pci 0000:00:00.1: BAR 0: assigned [mem 0x40001000-0x40001fff]
Later the device driver shows this error:
ath5k 0000:00:03.0: cannot remap PCI memory region
ath5k: probe of 0000:00:03.0 failed with error -5
I assume that the logic chip which usually supresses the signal to the CardBus
card has some settling time and without the delay it would still let the
Cardbus interfere with the response from the MiniPCI card.
What I cannot explain is why this behaviour shows up now and not in earlier
kernel versions before. Maybe older PCI code was slower?
Signed-off-by: Bruno Randolf <br1@einfach.org>
Cc: linux-mips@linux-mips.org
Cc: manuel.lauss@googlemail.com
Cc: florian@openwrt.org
Patchwork: https://patchwork.linux-mips.org/patch/4087/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove the loop in the cascade handler and instead unconditionally
handle just the first set interrupt coming from the CPLD.
This gets rid of a lot of spurious interrupts being triggered for
the SMSC91111 ethernet chip especially under high(er) IDE load:
"eth0: spurious interrupt (mask = 0xb3)"
Verified on DB1200 and DB1300.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3288/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
YAMON on all devboards provides the "memsize" envvar; in the unlikely
case that it can't be parsed just assume 64MB, which all boards have
at least.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3286/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
- Updates to mxc_nand and gpmi drivers to support new boards and device tree
- Improve consistency of information about ECC strength in NAND devices
- Clean up partition handling of plat_nand
- Support NAND drivers without dedicated access to OOB area
- BCH hardware ECC support for OMAP
- Other fixes and cleanups, and a few new device IDs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iEYEABECAAYFAk/JG1wACgkQdwG7hYl686M80wCglN4kutx20j+KJWuZofkr9Hog
weEAoI4jrqEWEdW9EcT2CIWQw7eG+1v+
=7tdo
-----END PGP SIGNATURE-----
Merge tag 'for-linus-3.5-20120601' of git://git.infradead.org/linux-mtd
Pull mtd update from David Woodhouse:
- More robust parsing especially of xattr data in JFFS2
- Updates to mxc_nand and gpmi drivers to support new boards and device tree
- Improve consistency of information about ECC strength in NAND devices
- Clean up partition handling of plat_nand
- Support NAND drivers without dedicated access to OOB area
- BCH hardware ECC support for OMAP
- Other fixes and cleanups, and a few new device IDs
Fixed trivial conflict in drivers/mtd/nand/gpmi-nand/gpmi-nand.c due to
added include files next to each other.
* tag 'for-linus-3.5-20120601' of git://git.infradead.org/linux-mtd: (75 commits)
mtd: mxc_nand: move ecc strengh setup before nand_scan_tail
mtd: block2mtd: fix recursive call of mtd_writev
mtd: gpmi-nand: define ecc.strength
mtd: of_parts: fix breakage in Kconfig
mtd: nand: fix scan_read_raw_oob
mtd: docg3 fix in-middle of blocks reads
mtd: cfi_cmdset_0002: Slight cleanup of fixup messages
mtd: add fixup for S29NS512P NOR flash.
jffs2: allow to complete xattr integrity check on first GC scan
jffs2: allow to discriminate between recoverable and non-recoverable errors
mtd: nand: omap: add support for hardware BCH ecc
ARM: OMAP3: gpmc: add BCH ecc api and modes
mtd: nand: check the return code of 'read_oob/read_oob_raw'
mtd: nand: remove 'sndcmd' parameter of 'read_oob/read_oob_raw'
mtd: m25p80: Add support for Winbond W25Q80BW
jffs2: get rid of jffs2_sync_super
jffs2: remove unnecessary GC pass on sync
jffs2: remove unnecessary GC pass on umount
jffs2: remove lock_super
mtd: gpmi: add gpmi support for mx6q
...
These will show up as a build failure once we clean up a
misuse of module.h in the mips termios header.
Uses export.h: (EXPORT_SYMBOL)
arch/mips/cavium-octeon/setup.c
arch/mips/pmc-sierra/yosemite/setup.c
arch/mips/rb532/devices.c
arch/mips/sni/setup.c
Uses module.h: (symbol_get/put)
arch/mips/alchemy/devboards/db1200.c
Uses module.h: (print_modules)
arch/mips/kernel/traps.c
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3448/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use the default partition parser, cmdlinepart, provided by the plat_nand driver.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Since a clocksource change post 3.2-rc1, tasks on my DB1500 board
hang after random amounts of time (from a few minutes to a few hours),
regardless of load. Debugging showed that the compare-match register
value is a few seconds lower than the current counter value.
The minimum value of 8 was initialy determined by a trial-and-error
approach. Currently it is sufficient for all Alchemys (without PCI
apparently), independent of CPU clock; only the DB1500 and DB1550
boards experience these timer-related tasks hangs now.
This patch increases the minimum timeout by 1 (to 9 counter ticks)
which seems sufficient since the systems are still working perfectly
fine after over 24 hours.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3214/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The PB1200 has the CPLD located at an address which on the DB1200 is
RAM; reading the Board-ID sometimes results in a PB1200 being detected
instead (especially during reboots after long uptimes).
On the other hand, the address of the DB1200's CPLD is hosting Flash
chips on the PB1200. Test for the DB1200 first and additionally do a
quick write-test to the hexleds register to make sure we're writing
to the CPLD.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3005/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
With a generic plat_irq_dispatch (for Alchemy at least) code for both
interrupt controller types can coexist in a single kernel image and be
autodetected at runtime.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2935/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add necessary transceiver control platform data and hook up the
IrDA peripheral on the DB1000 and DB1100 boards.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2878/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since commit [e58aa3d2: genirq: Run irq handlers with interrupts disabled],
We run all interrupt handlers with interrupts disabled and we even check
and yell when an interrupt handler returns with interrupts enabled (see
commit [b738a50a: genirq: Warn when handler enables interrupts]).
So now this flag is a NOOP and can be removed.
[ralf@linux-mips.org: Fixed up conflicts in
arch/mips/alchemy/common/dbdma.c, arch/mips/cavium-octeon/smp.c and
arch/mips/kernel/perf_event.c.]
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
To: linux-kernel@vger.kernel.org
Cc: tglx@linutronix.delinux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2835/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
All Devboards can use the 32kHz counter as a RTC device.
Also delete the custom CMOS RTC header, which can be used for the
DS1693 on the PB1500. But since it doesn't have a buffer battery
it is as useful as the on-chip RTC which I prefer.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2874/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
These 3 boards are very similar; with this patch a single kernel image
which runs on all three can be built.
Tested on DB1500 and DB1100.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2872/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The PB1200 is basically a DB1200 with additional MMC and camera sockets
and different base addresses for external hardware (CPLD, IDE, Net, NAND).
This patch implements the missing PB1200 features in DB1200 support code
and runtime board detection.
Tested on DB1200 only.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2880/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Most of these files are have more comments than real code; merge
them all into single board-<name>.c files.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2869/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add basic support for the Au1300 variant(s):
- New GPIO/Interrupt controller
- DBDMA ids
- USB setup
- MMC support
- enable various PSC drivers
- detection code.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2866/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Initially I had to write to both the MASK and ENABLE registers, otherwise
the CPLD would generate tons of spurious interrupts. With the change to
the demux handler to disable the muxed line, it is now sufficient to
disable the interrupt by writing either the enable or mask register.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2865/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
No test hardware and no (apparent) users. These boards seem very
similar to the DB1500, so if required support can be brought back
again (I have datasheets) but then with dedicated board code, not
tacked on to DB1000 support.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2864/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (549 commits)
ALSA: hda - Fix ADC input-amp handling for Cx20549 codec
ALSA: hda - Keep EAPD turned on for old Conexant chips
ALSA: hda/realtek - Fix missing volume controls with ALC260
ASoC: wm8940: Properly set codec->dapm.bias_level
ALSA: hda - Fix pin-config for ASUS W90V
ALSA: hda - Fix surround/CLFE headphone and speaker pins order
ALSA: hda - Fix typo
ALSA: Update the sound git tree URL
ALSA: HDA: Add new revision for ALC662
ASoC: max98095: Convert codec->hw_write to snd_soc_write
ASoC: keep pointer to resource so it can be freed
ASoC: sgtl5000: Fix wrong mask in some snd_soc_update_bits calls
ASoC: wm8996: Fix wrong mask for setting WM8996_AIF_CLOCKING_2
ASoC: da7210: Add support for line out and DAC
ASoC: da7210: Add support for DAPM
ALSA: hda/realtek - Fix DAC assignments of multiple speakers
ASoC: Use SGTL5000_LINREG_VDDD_MASK instead of hardcoded mask value
ASoC: Set sgtl5000->ldo in ldo_regulator_register
ASoC: wm8996: Use SND_SOC_DAPM_AIF_OUT for AIF2 Capture
ASoC: wm8994: Use SND_SOC_DAPM_AIF_OUT for AIF3 Capture
...
Now that no driver any longer depends on the CONFIG_SOC_AU1??? symbols,
it's time to get rid of them: Move some of the platform devices to the
boards which can use them, Rename a few (unused) constants in the header,
Replace them with MIPS_ALCHEMY in the various Kconfig files. Finally
delete them altogether from the Alchemy Kconfig file.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2707/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch gets rid of all CONFIG_SOC_AU1XXX defines in
DMA/DBDMA-related code.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2704/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
au1xxx-ide uses defines from the pb1200/db1200 headers:
get DBDMA ID through platform resource information,
hardcode register spacing. The only 2 users of this driver (and
the only boards it can really work on realiably) use the same
register layout.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: linux-ide@vger.kernel.org
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: linux-ide@vger.kernel.org
Acked-by: David S. Miller <davem@davemloft.net>
Patchwork: https://patchwork.linux-mips.org/patch/2716/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
remove all redundant peripheral base address defines, fix
all affected boards and drivers.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2700/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use runtime CPU detection to setup all USB parts.
Remove the Au1200 OTG and UDC platform devices since there are no
drivers for them anyway.
Clean up the USB address mess in the au1000 header.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2703/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Alchemy chips have one or more registers which control access
to the usb blocks as well as PHY configuration. I don't want
the OHCI/EHCI glues to know about the different registers and bits;
new code hides the gory details of USB configuration from them.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: linux-usb@vger.kernel.org
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Patchwork: https://patchwork.linux-mips.org/patch/2709/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
create mode 100644 drivers/usb/host/alchemy-common.c
For GPIOLIB=y decide at runtime which gpiochips to register;
in the GPIOLIB=n case, the gpio headers need to be reshuffled
a bit to make multiple implementations coexist peacefully.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2679/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
No reason NOT to build it
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2678/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch removes the last hardcoded base address from the au1000_eth
driver. The base address of the MACDMA unit was derived from the
platform device id; if someone registered the MACs in inverse order
both would not work.
So instead pass the base address of the DMA unit to the driver with
the other platform resource information.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Acked-by: David S. Miller <davem@davemloft.net>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2674/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Disable the cascade IRQ in the cascade handler. This is required to
get the DB1300 working, and also gets rid of all spurious interrupts
previously observed on the DB1200; so Config[OD] can be disabled
again for better performance.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2708/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The current code forgets the Au1100 when looking for the correct method to
suspend the chip.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2675/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Harmless typo which prints an error message although MAC0 was registered
successfully.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2672/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The use of the "soc-audio" platform device is no longer en vogue,
update the code to the newer, simpler way of doing things.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The PSC audio drivers (psc-ac97/psc-i2s) register the DMA platform_device
on their own. This is frowned upon, from now on board code must
register a simple pcm dma platform device for each PSC with sound duties.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add a machine driver suitable for the AC97 part on the DB1000/DB1500/DB1100
boards.
Run-tested on DB1500.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* 'timers-clocksource-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
clocksource: convert mips to generic i8253 clocksource
clocksource: convert x86 to generic i8253 clocksource
clocksource: convert footbridge to generic i8253 clocksource
clocksource: add common i8253 PIT clocksource
blackfin: convert to clocksource_register_hz
mips: convert to clocksource_register_hz/khz
sparc: convert to clocksource_register_hz/khz
alpha: convert to clocksource_register_hz
microblaze: convert to clocksource_register_hz/khz
ia64: convert to clocksource_register_hz/khz
x86: Convert remaining x86 clocksources to clocksource_register_hz/khz
Make clocksource name const
remove au_readl/au_writel, remove the predefined GPIO1/2 KSEG1 register
addresses and fix the fallout in all boards and drivers.
This also fixes a bug in the mtx-1_wdt driver which was introduced by
commit 6ea8115bb6
("Convert mtx1 wdt to be a platform device and use generic GPIO API")
before this patch mtx-1_wdt only modified GPIO215, the patch then
used the gpio resource information as bit index into the GPIO2 register
but the conversion to the GPIO API didn't realize that.
With this patch the drivers original behaviour is restored and GPIO15
is left alone.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: Florian Fainelli <florian@openwrt.org>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: linux-watchdog@vger.kernel.org
Cc: Wim Van Sebroeck <wim@iguana.be>
Patchwork: https://patchwork.linux-mips.org/patch/2381/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org
According to the databooks, the Au1000 DMA engine must be programmed with
the physical FIFO addresses. This patch does that; furthermore this
opened the possibility to get rid of a lot of now unnecessary address
defines.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Patchwork: https://patchwork.linux-mips.org/patch/2348/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org
Rewrite ethernet setup to use runtime cpu detection, and also clean up
the ethernet base address mess as far as possible.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Patchwork: https://patchwork.linux-mips.org/patch/2353/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org
Detect CPU type at runtime and setup uarts accordingly; also clean up the
uart base address mess in the process as far as possible.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Patchwork: https://patchwork.linux-mips.org/patch/2352/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org
Convert the PM sysdev to syscore_ops and clean up the ddma addresses a bit.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Patchwork: https://patchwork.linux-mips.org/patch/2351/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Convert the PM sysdev to use syscore_ops instead.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Patchwork: https://patchwork.linux-mips.org/patch/2350/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
replace au_readl/au_writel with __raw_readl/__raw_writel,
and clean up IC-related stuff from the headers.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Patchwork: https://patchwork.linux-mips.org/patch/2354/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Setting Config[OD] gets rid of a _LOT_ of spurious CPLD interrupts,
but also decreases overall performance a bit.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Patchwork: https://patchwork.linux-mips.org/patch/2347/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Conflicts:
arch/ia64/kernel/cyclone.c
arch/mips/kernel/i8253.c
arch/x86/kernel/i8253.c
Reason: Resolve conflicts so further cleanups do not conflict further
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This fixes:
alchemy/xxs1500/init.c: In function 'prom_init':
alchemy/xxs1500/init.c:57:17: error: ignoring return value of 'kstrtoul', declared with attribute warn_unused_result
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2340/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/alchemy/devboards/db1x00/board_setup.o
arch/mips/alchemy/devboards/db1x00/board_setup.c: In function 'board_setup':
arch/mips/alchemy/devboards/db1x00/board_setup.c:130:6: error: variable 'pin_func' set but not used [-Werror=unused-but-set-variable]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix the deadlock in set_type() while at it:
The code called set_irq_chip_and_handler_name() resp. set_irq_chip()
from the set_type() callback. That only works on UP and lock debugging
disabled. Otherwise it would dead lock on desc->lock.
__irq_set_chip_handler_name_locked() avoids that.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2173/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since commit 32fd6901 (MIPS: Alchemy: get rid of common/reset.c)
Alchemy-based boards use their own reset function. For MTX-1 and XXS1500,
the reset function pokes at the BCSR.SYSTEM_RESET register, but this does
not work. According to Bruno Randolf, this was not tested when written.
Previously, the generic au1000_restart() routine called the board specific
reset function, which for MTX-1 and XXS1500 did not work, but finally made
a jump to the reset vector, which really triggers a system restart. Fix
reboot for both targets by jumping to the reset vector.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2093/
Acked-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When au1000_eth probes the MII bus for PHY address, if we do not set
au1000_eth platform data's phy_search_highest_address, the MII probing
logic will exit early and will assume a valid PHY is found at address 0.
For MTX-1, the PHY is at address 31, and without this patch, the link
detection/speed/duplex would not work correctly.
CC: stable@kernel.org
Signed-off-by: Florian Fainelli <florian@openwrt.org>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2111/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This converts the mips clocksources to use clocksource_register_hz/khz
CC: Ralf Baechle <ralf@linux-mips.org>
CC: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Conflicts:
MAINTAINERS
arch/arm/mach-omap2/pm24xx.c
drivers/scsi/bfa/bfa_fcpim.c
Needed to update to apply fixes for which the old branch was too
outdated.
In commit 7d172bfe ("Alchemy: Add UART PM methods") I introduced
platform PM methods which call a function of the 8250 driver;
this patch works around link failures when the kernel is built
without 8250 support.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/1737/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
While at it, fix two checkpatch errors.
Several non-const struct instances constified by this patch were added after
the introduction of platform_suspend_ops in checkpatch.pl's list of "should
be const" structs (79404849e9).
Patch against mainline.
Inspired by hunks of the grsecurity patch, updated for newer kernels.
Signed-off-by: Lionel Debroux <lionel_debroux@yahoo.fr>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (365 commits)
ALSA: hda - Disable sticky PCM stream assignment for AD codecs
ALSA: usb - Creative USB X-Fi volume knob support
ALSA: ca0106: Use card specific dac id for mute controls.
ALSA: ca0106: Allow different sound cards to use different SPI channel mappings.
ALSA: ca0106: Create a nice spot for mapping channels to dacs.
ALSA: ca0106: Move enabling of front dac out of hardcoded setup sequence.
ALSA: ca0106: Pull out dac powering routine into separate function.
ALSA: ca0106 - add Sound Blaster 5.1vx info.
ASoC: tlv320dac33: Use usleep_range for delays
ALSA: usb-audio: add Novation Launchpad support
ALSA: hda - Add workarounds for CT-IBG controllers
ALSA: hda - Fix wrong TLV mute bit for STAC/IDT codecs
ASoC: tpa6130a2: Error handling for broken chip
ASoC: max98088: Staticise m98088_eq_band
ASoC: soc-core: Fix codec->name memory leak
ALSA: hda - Apply ideapad quirk to Acer laptops with Cxt5066
ALSA: hda - Add some workarounds for Creative IBG
ALSA: hda - Fix wrong SPDIF NID assignment for CA0110
ALSA: hda - Fix codec rename rules for ALC662-compatible codecs
ALSA: hda - Add alc_init_jacks() call to other codecs
...
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (49 commits)
serial8250: ratelimit "too much work" error
serial: bfin_sport_uart: speed up sport RX sample rate to be 3% faster
serial: abstraction for 8250 legacy ports
serial/imx: check that the buffer is non-empty before sending it out
serial: mfd: add more baud rates support
jsm: Remove the uart port on errors
Alchemy: Add UART PM methods.
8250: allow platforms to override PM hook.
altera_uart: Don't use plain integer as NULL pointer
altera_uart: Fix missing prototype for registering an early console
altera_uart: Fixup type usage of port flags
altera_uart: Make it possible to use Altera UART and 8250 ports together
altera_uart: Add support for different address strides
altera_uart: Add support for getting mapbase and IRQ from resources
altera_uart: Add support for polling mode (IRQ-less)
serial: Factor out uart_poll_timeout() from 8250 driver
serial: mark the 8250 driver as maintained
serial: 8250: Don't delay after transmitter is ready.
tty: MAINTAINERS: add drivers/serial/jsm/ as maintained driver
vcs: invoke the vt update callback when /dev/vcs* is written to
...
Custom UART PM hook for Alchemy chips: do standard UART pm and
additionally en/disable uart block clocks as needed.
This allows to get rid of a debug port PM hack in the Alchemy pm code.
Tested on Db1200.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add missing #inclusions of <linux/irq.h> to a whole bunch of files that should
really include it. Note that this can replace #inclusions of <asm/irq.h>.
This is required for the patch to sort out irqflags handling function naming to
compile on MIPS.
The problem is that these files require access to things like setup_irq() -
which isn't available by #including <linux/interrupt.h>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
The function prom_init_cmdline() references the variable __initdata
arcs_cmdline.
The function prom_get_ethernet_addr() references the variable __initdata
arcs_cmdline.
Annotate prom_init_cmdline() as __init, unexport and annotate
prom_get_ethernet_addr() since it's no longer called from within
driver code.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/1547/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch fixes up the au1x audio platform after the multi-component
merge:
- compile fixes and updates to get DB1200 platform audio working again,
- removal of global variables in AC97/I2S/DMA(PCM) modules.
The AC97 part is limited to one instance only for now due to issues
with getting at driver data in the soc_ac97_ops.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
From: Wolfgang Grandegger <wg@denx.de>
Add basic support for the General Purpose Router (GPR) board from
Trapeze ITS.
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1460/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
au1000_eth uses firmware calls to get a valid MAC address, and changes
it depending on platform device id. This patch moves this logic out of
the driver into the platform device registration part, where boards with
supported chips can use whatever firmware interface they need; the default
implementation maintains compatibility with existing, YAMON-based firmware.
Tested-by: Wolfgang Grandegger <wg@denx.de>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: netdev@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/1481/
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove the SERIAL_8250_AU1X00 config symbol. Instead, use the MIPS_ALCHEMY
one which is always defined when building an Au1x00-based platform.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Linux-serial <linux-serial@vger.kernel.org>
Patchwork: https://patchwork.linux-mips.org/patch/1461/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This one depends on a previous patch (which removes SOC_AU1X00 and changes
MACH_ALCHEMY) to apply cleanly (and then actually work), so I'd love for
this to go in via the mips tree.
Remove the CONFIG_SOC_AU1X00 Kconfig symbol since its job can also be done
by MACH_ALCHEMY, now renamed to MIPS_ALCHEMY.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/1461/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
[Ralf: Remove a forgotten -Werror in Pb1200 Makefile.]
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Manuel Lauss <manuel.lauss@googlemail.com>
Patchwork: https://patchwork.linux-mips.org/patch/1319/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Replace deprecated DMA_32BIT_MASK with DMA_BIT_MASK. This is needed because
the new style platform makefiles will enable -Werror.
cc1: warnings being treated as errors
arch/mips/alchemy/devboards/db1200/platform.c:219: error: 'DMA_nnBIT_MASK' is deprecated
arch/mips/alchemy/devboards/db1200/platform.c:226: error: 'DMA_nnBIT_MASK' is deprecated
arch/mips/alchemy/devboards/db1200/platform.c:388: error: 'DMA_nnBIT_MASK' is deprecated
arch/mips/alchemy/devboards/db1200/platform.c:393: error: 'DMA_nnBIT_MASK' is deprecated
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
To: linux-mips@linux-mips.org
Acked-by: Manuel Lauss <manuel.lauss@googlemail.com>
Patchwork: https://patchwork.linux-mips.org/patch/1427/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Preparatory step for moving Alchemy over to new MIPS Platform
build system support.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/1318/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/alchemy/mtx-1/board_setup.o
{standard input}: Assembler messages:
{standard input}:263: Error: opcode not supported on this processor: mips1 (mips1) `sync'
{standard input}:274: Error: opcode not supported on this processor: mips1 (mips1) `sync'
{standard input}:296: Error: opcode not supported on this processor: mips1 (mips1) `sync'
[...]
Any .set mipsX statement other than .set mips0 at the end of inline
assembler is a big fat bug.
Introduced by 9482eabeca315c0276ffb50026b7482481b7097b (linux-mips.org) rsp.
32fd6901a6 (kernel.org).
While at it, fix the same issue in
arch/mips/alchemy/devboards/pb1000/board_setup.c
arch/mips/alchemy/xxs1500/board_setup.c
as well.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Currently, the eth devices are probed in the inverse order, first
au1xxx_eth1_device and then au1xxx_eth0_device. On the GPR board,
this makes trouble:
# ifconfig|grep HWaddr
eth0 Link encap:Ethernet HWaddr 00:50:C2:0C:30:01
eth1 Link encap:Ethernet HWaddr 66:22:01:80:38:10
A bogous ethernet hwaddr is assigned to the first device and
au1xxx_eth0_device is mapped to eth1, which even does not work
properly. With this patch, the problems are gone:
# ifconfig|grep HWaddr
eth0 Link encap:Ethernet HWaddr 66:22:11:32:38:10
eth1 Link encap:Ethernet HWaddr 66:22:11:32:38:11
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1473/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch fixes a regression introduced by commit "MIPS: Alchemy: MTX-1:
Use linux gpio api." (bb706b28bb) which broke
PCI bus operation. The problem is caused by alchemy_gpio2_enable() which
resets the GPIO2 block. Two PCI signals (PCI_SERR and PCI_RST) are connected
to GPIO2 and they obviously do not to like the reset. Since GPIO2 is
correctly initialized by the boot monitor (YAMON) it is not necessary to
call this function, so just remove it.
Also replace gpio_set_value() with alchemy_gpio_set_value() to avoid
problems in case gpiolib gets initialized after PCI. And since alchemy
gpio_set_value() calls au_sync() we don't have to au_sync() again later.
Signed-off-by: Bruno Randolf <br1@einfach.org>
To: linux-mips@linux-mips.org
To: manuel.lauss@googlemail.com
Patchwork: https://patchwork.linux-mips.org/patch/1448/
Tested-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Split the low-level sleepcode into per-cpu functions instead of
relying on compile-time-defined cpu type.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/1281/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add a sysdev for DBDMA PM.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/1119/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use a sysdev to implement PM methods for the Au1000 interrupt controllers.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/1114/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Bruno Randolf
Ralf Baechle
Thomas Meyer
Florian Fainelli
Manuel Lauss
Linus Torvalds
Paul Gortmaker
H Hartley Sweeten
Yong Zhang
Thomas Gleixner
Lucas De Marchi
John Stultz
Jiri Kosina
Yoichi Yuasa
Lionel Debroux
Uwe Kleine-König
Takashi Iwai
David Howells
Wolfgang Grandegger
Bruno Randolf
Christoph Egger
FUJITA Tomonori
Wolfgang Grandegger