The register providing the pll lock status is at a different address on the
rk3066. The error became apparent while working on cpufreq support for
the rockchip SoCs.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The Rockchip PLL code switches into slow mode (AKA bypass more AKA
24MHz mode) before actually changing the PLL. This keeps anyone from
using the PLL while it's changing. However, in all known Rockchip
SoCs nobody should ever see the 24MHz when changing the PLL supplying
the armclk because we should reparent children to an alternate
(faster than 24MHz) PLL.
One problem is that the code to switch to an alternate parent was
running in PRE_RATE_CHANGE. ...and the code to switch to slow mode
was _also_ running in PRE_RATE_CHANGE. That meant there was no real
guarantee that we would switch to an alternate parent before switching
to 24MHz mode.
Let's move the switch to "slow mode" straight into
rockchip_rk3066_pll_set_rate(). That means we're guaranteed that the
24MHz is really a last-resort.
Note that without this change on real systems we were the code to
switch to an alternate parent at 24MHz. In some older versions of
that code we'd appy a (temporary) / 5 to the 24MHz causing us to run
at 4.8MHz. That wasn't enough to service USB interrupts in some cases
and could lead to a system hang.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
If CONFIG_COMMON_CLK is selected then __clk_get and __clk_put are
defined in drivers/clk/clk.c and declared in include/linux/clkdev.h.
Sylwester's series[0] to properly support clk_{get,put} in the common
clock framework made changes to the asm-specific clkdev.h headers, but
not the asm-generic version. Tomeu's recent changes[1] to introduce a
provider/consumer split in the clock framework uncovered this problem,
causing the following build error on any architecture using the
asm-generic clkdev.h (e.g. x86 architecture and the ACPI LPSS driver):
In file included from drivers/acpi/acpi_lpss.c:15:0:
include/linux/clkdev.h:59:5: error: conflicting types for ‘__clk_get’
int __clk_get(struct clk_core *clk);
^
In file included from arch/x86/include/generated/asm/clkdev.h:1:0,
from include/linux/clkdev.h:15,
from drivers/acpi/acpi_lpss.c:15:
include/asm-generic/clkdev.h:20:19: note: previous definition of ‘__clk_get’ was here
static inline int __clk_get(struct clk *clk) { return 1; }
^
Fixed by only declarating __clk_get and __clk_put when
CONFIG_COMMON_CLK is set.
[0] http://lkml.kernel.org/r/<1386177127-2894-5-git-send-email-s.nawrocki@samsung.com>
[1] http://lkml.kernel.org/r/<1409758148-20104-1-git-send-email-tomeu.vizoso@collabora.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
There is no need to init .owner field.
Based on the patch from Peter Griffin <peter.griffin@linaro.org>
"mmc: remove .owner field for drivers using module_platform_driver"
This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway."
Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch add the clock node in PD_VIDEO
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch use the new defined clock ID to initial the clock nodes.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch add some clock binding id for different modules
that under development and going to send upstream.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The npll on rk3288 is exactly the same pll type as the other 4. Yet it
was missing the link to the rate table, making rate changes impossible.
Change that by setting the table.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The rk3288 actually has 12 softresets, so fix the register count.
Signed-off-by: Mark yao <mark.yao@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The patch add the rest of the indices of the additional reset
registers from the updated TRM.
Signed-off-by: Mark yao <mark.yao@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The dwc2 usb controller also uses agressive clock gating, which in this
case leads to hclk_peri getting disabled and hanging the system.
Therefore move it to the critical clocks until we also control that
part of the system.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
On 32bit architectures, like ARM calculating the fractional rate will
do the multiplication before converting the value to u64 when it gets
assigned to ret, which can produce overflows.
The error in question happened with a parent_rate of 386MHz, m = 3000,
n = 60000, which resulted in a wrong rate value of 15812Hz.
Therefore cast parent_rate to u64 to make sure the multiplication
happens in a 64bit space and produces the correct 192MHz in the example.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add Device Tree binding documentation for the clocks
outputs in the Maxim 77802 Power Management IC.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The MAX77802 PMIC has two 32.768kHz Buffered Clock Outputs with
Low Jitter Mode. This patch adds support for these two clocks.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Like most clock drivers, the Maxim 77686 PMIC clock binding
follows the convention that the "#clock-cells" property is
used to specify the number of cells in a clock provider.
But the binding document is not clear enough that it shall
be set to 1 since the PMIC support multiple clocks outputs.
Also, explain that the clocks identifiers are defined in a
header file that can be included by Device Tree source with
client nodes to avoid using magic numbers.
Finally, add "clock-output-names" as an optional property
since now is supported by the clock driver.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Clocks drivers for Maxim PMIC are very similar so they can
be converted to use the generic Maxim clock driver.
Also, while being there use module_platform_driver() helper
macro to eliminate more boilerplate code.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Maxim Integrated Power Management ICs are very similar with
regard to their clock outputs. Most of the clock drivers for
these chips are duplicating code and are simpler enough that
can be converted to use a generic driver to consolidate code
and avoid duplication.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch adds a dt-binding include for Maxim 77686
PMIC clock IDs that can be used by both the max77686
clock driver and Device Tree source files.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Since commit 54196ccbe0 (of: consolidate linker section OF match table
declarations) which went into 3.16-rc1 the following compiler warning is
generated:
In file included from drivers/clk/clk-efm32gg.c:12:0: include/linux/of.h:772:20:
warning: comparison of distinct pointer types lacks a cast [enabled by default]
.data = (fn == (fn_type)NULL) ? fn : fn }
^
include/linux/of.h:785:3: note: in expansion of macro '_OF_DECLARE'
_OF_DECLARE(table, name, compat, fn, of_init_fn_1)
^
include/linux/clk-provider.h:545:42: note: in expansion of macro 'OF_DECLARE_1'
#define CLK_OF_DECLARE(name, compat, fn) OF_DECLARE_1(clk, name, compat, fn)
^
drivers/clk/clk-efm32gg.c:81:1: note: in expansion of macro 'CLK_OF_DECLARE'
CLK_OF_DECLARE(efm32ggcmu, "efm32gg,cmu", efm32gg_cmu_init);
^
Fix it by making efm32gg_cmu_init return void.
Cc: Rob Herring <robh@kernel.org>
Reported-by: Bryan Hundven <bryanhundven@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Use __initconst instead of __initdata for constant init data.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
As checkpatch suggests:
WARNING: Possible unnecessary 'out of memory' message,
remove an error message after failing kmalloc() from the PLL driver.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
In some cases, clocks can switch their parent with clk_set_rate, for
example clk_mux can do this in some cases. Current implementation of
clk_change_rate uses un-safe list iteration on the clock children, which
will cause wrong clocks to be parsed in case any of the clock children
change their parents during the change rate operation. Fixed by using
the safe list iterator instead.
The problem was detected due to some divide by zero errors generated
by clock init on dra7-evm board, see discussion under
http://article.gmane.org/gmane.linux.ports.arm.kernel/349180 for details.
Fixes: 71472c0c06 ("clk: add support for clock reparent on set_rate")
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The clocks for i2c1 and i2c2 are flipped. The clock tree matched the
Technical Reference Manual (TRM) but the TRM was wrong. Swap them in
the clock tree. This was determined experimentally (by Addy) and
confirmed by the Rockchip IC team.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reported-by: Addy Ke <addy.ke@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The pre-divider for the sdc clocks only has 2 bits in it, so we
can't possibly divide by anything larger than 4 here.
Furthermore, we program the value of ~(n - m) and the n value is
larger than 8 bits (max of 256). Replace this entry with 200kHz
which is close enough to 144kHz to be usable.
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Andy Gross <agross@codeaurora.org>
Fixes: 24d8fba44a "clk: qcom: Add support for IPQ8064's global clock controller (GCC)"
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Test rate value before calculating the div value to avoid div by zero.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Reported-by: Gaël PORTAY <gael.portay@gmail.com>
Tested-by: Gaël PORTAY <gael.portay@gmail.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The RM9200 USB clock is actually connected to a single parent (the PLLB)
on which we can apply a specific divider.
The USB clock divider does not allow for fine grained control on the USB
clock frequency, hence propagating the set_rate request to the parent is
the only choice we have to properly configure the USB clock rate.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Reported-by: Gaël PORTAY <gael.portay@gmail.com>
Tested-by: Gaël PORTAY <gael.portay@gmail.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Use the cached values to calculate PLL rate instead of the register values.
This is required to prevent erroneous PLL rate return when the PLL rate
has been configured but the PLL is not prepared yet.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Reported-by: Gaël PORTAY <gael.portay@gmail.com>
Tested-by: Gaël PORTAY <gael.portay@gmail.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The AT91 PLL rate configuration is done by configuring a multiplier/divider
pair.
The previous calculation was over-complicated (and apparently buggy).
Simplify the implementation and add some comments to explain what is done
here.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Reported-by: Gaël PORTAY <gael.portay@gmail.com>
Tested-by: Gaël PORTAY <gael.portay@gmail.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The clock-tree contains clocks that should never get disabled automatically.
One example are the base ACLKs, the base supplies for all peripherals.
Therefore add a structure similar to the sunxi clock-tree to protect these
special clocks from being disabled.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Doug Anderson <dianders@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
It is only used locally in clk/rockchip/clk.c and thus can be static.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Rockchip SoCs may provide fraction dividers for some clocks, mostly for
i2s and uarts. In contrast to the other registers, these do not use
the hiword-mask paradigm, but instead split the register into the upper
16 bit for the nominator and the lower 16 bit for the denominator.
The common clock framework got a generic fractional divider clock type
recently that can accomodate this setting easily. All currently known
fraction dividers have a separate gate too, therefore implement the
divider as composite using the ops-struct from fractional_divider clock
and add the gate if necessary.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
10cdfe9f32
(clk: shmobile: Add R-Car Gen2 clocks support)
added R-Car Gen2 clock support via DT for v3.14.
But, cpg_sd01_div_table is missing
"0x0100: x 1/8" division ratio.
This patch fixes hidden bug.
It is based on R-Car H2 v0.7, R-Car M2 v0.9.
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Reported-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The powersave clock acts like a multiplexer for the cpu, selecting
either the clock signal derived from the cpu pll or from the ddr clock.
This patch changes powersave from a gate clock to a mux clock to better
reflect this behavior.
This is a cleaner approach whereby the frequency of the cpu always
matches the rate of powersave_clk. The cpufreq driver for the kirkwood
platform no longer must parse this behavior out of various calls to
clk_enable and clk_disable, but can instead simply select the parent cpu
it wants when changing rate. Likewise when requesting the cpu rate we
need only query powersave_clk's rate through the usual call to
clk_get_rate.
The new clock data and corresponding changes to the cpufreq driver are
combined into this single commit to avoid a git bisect issue where this
cpufreq driver fails to work properly between the commit that updates
the kirkwood clock driver and the commit that changes how the cpufreq
driver uses that clock.
Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The slow clk block provided by at91sam9260 and derived SoCs should always
have 2 parents.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Kirkwood is unique among the mvebu SoCs for having a clock multiplexer
that feeds into the cpu. This multiplexer can select either the cpu pll
or the ddr clock as its input signal, allowing for a choice between
performance and power savings.
This patch introduces the code needed to register the clock multiplexer
on Kirkwood SoCs but does not include the clock data to actually
register the clock. That will be done in a follow-up patch which is
necessary to prevent breaking git bisect.
Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Refactor mvebu_clk_gating_setup() to use a common spinlock instead of a
unique lock for every instance of a struct clk_gating_ctrl object. This
will be used later for a separate mux clock type that shares a register
with gate clock types and needs to use the same lock to protect access
to the register.
Cc: Andrew Lunn <andrew@lunn.ch>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
- support highmem on cores with aliasing data cache. Enable highmem on kc705
by default;
- simplify addition of new core variants (no need to modify Kconfig /
Makefiles);
- improve robustness of unaligned access handler and its interaction with
window overflow/underflow exception handlers;
- deprecate atomic and spill registers syscalls;
- clean up Kconfig: remove orphan MATH_EMULATION, sort 'select' statements;
- wire up renameat2 syscall.
Various fixes:
- fix address checks in dma_{alloc,free}_coherent (runtime BUG);
- fix access to THREAD_RA/THREAD_SP/THREAD_DS (debug build breakage);
- fix TLBTEMP_BASE_2 region handling in fast_second_level_miss (runtime
unrecoverable exception);
- fix a6 and a7 handling in fast_syscall_xtensa (runtime userspace register
clobbering);
- fix kernel/user jump out of fast_unaligned (potential runtime unrecoverabl
exception);
- replace termios IOCTL code definitions with constants (userspace build
breakage).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=mAYX
-----END PGP SIGNATURE-----
Merge tag 'xtensa-20140830' of git://github.com/czankel/xtensa-linux
Pull Xtensa updates from Chris Zankel:
"Xtensa improvements for 3.17:
- support highmem on cores with aliasing data cache. Enable highmem
on kc705 by default
- simplify addition of new core variants (no need to modify Kconfig /
Makefiles)
- improve robustness of unaligned access handler and its interaction
with window overflow/underflow exception handlers
- deprecate atomic and spill registers syscalls
- clean up Kconfig: remove orphan MATH_EMULATION, sort 'select'
statements
- wire up renameat2 syscall.
Various fixes:
- fix address checks in dma_{alloc,free}_coherent (runtime BUG)
- fix access to THREAD_RA/THREAD_SP/THREAD_DS (debug build breakage)
- fix TLBTEMP_BASE_2 region handling in fast_second_level_miss
(runtime unrecoverable exception)
- fix a6 and a7 handling in fast_syscall_xtensa (runtime userspace
register clobbering)
- fix kernel/user jump out of fast_unaligned (potential runtime
unrecoverabl exception)
- replace termios IOCTL code definitions with constants (userspace
build breakage)"
* tag 'xtensa-20140830' of git://github.com/czankel/xtensa-linux: (25 commits)
xtensa: deprecate fast_xtensa and fast_spill_registers syscalls
xtensa: don't allow overflow/underflow on unaligned stack
xtensa: fix a6 and a7 handling in fast_syscall_xtensa
xtensa: allow single-stepping through unaligned load/store
xtensa: move invalid unaligned instruction handler closer to its users
xtensa: make fast_unaligned store restartable
xtensa: add double exception fixup handler for fast_unaligned
xtensa: fix kernel/user jump out of fast_unaligned
xtensa: configure kc705 for highmem
xtensa: support highmem in aliasing cache flushing code
xtensa: support aliasing cache in kmap
xtensa: support aliasing cache in k[un]map_atomic
xtensa: implement clear_user_highpage and copy_user_highpage
xtensa: fix TLBTEMP_BASE_2 region handling in fast_second_level_miss
xtensa: allow fixmap and kmap span more than one page table
xtensa: make fixmap region addressing grow with index
xtensa: fix access to THREAD_RA/THREAD_SP/THREAD_DS
xtensa: add renameat2 syscall
xtensa: fix address checks in dma_{alloc,free}_coherent
xtensa: replace IOCTL code definitions with constants
...
unicore32 builds fail with
arch/unicore32/kernel/signal.c: In function ‘setup_frame’:
arch/unicore32/kernel/signal.c:257: error: ‘usig’ undeclared (first use in this function)
arch/unicore32/kernel/signal.c:279: error: ‘usig’ undeclared (first use in this function)
arch/unicore32/kernel/signal.c: In function ‘handle_signal’:
arch/unicore32/kernel/signal.c:306: warning: unused variable ‘tsk’
arch/unicore32/kernel/signal.c: In function ‘do_signal’:
arch/unicore32/kernel/signal.c:376: error: implicit declaration of function ‘get_signsl’
make[1]: *** [arch/unicore32/kernel/signal.o] Error 1
make: *** [arch/unicore32/kernel/signal.o] Error 2
Bisect points to commit 649671c90e ("unicore32: Use get_signal()
signal_setup_done()").
This code never even compiled. Reverting the patch does not work, since
previously used functions no longer exist, so try to fix it up. Compile
tested only.
Fixes: 649671c90e ("unicore32: Use get_signal() signal_setup_done()")
Cc: Richard Weinberger <richard@nod.at>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Heiko Stuebner
Doug Anderson
Mike Turquette
Kiran Padwal
Kever Yang
Mark yao
Stephen Boyd
Javier Martinez Canillas
Uwe Kleine-König
Soren Brinkmann
Tero Kristo
Boris BREZILLON
Kuninori Morimoto
Ulrich Hecht
Linus Torvalds
Guenter Roeck