The ISI_CFG2.YCC_SWAP field controls color component ordering. The
datasheet lists the following orderings for the memory formats.
YCC_SWAP Byte 0 Byte 1 Byte 2 Byte 3
00: Default Cb(i) Y(i) Cr(i) Y(i+1)
01: Mode1 Cr(i) Y(i) Cb(i) Y(i+1)
10: Mode2 Y(i) Cb(i) Y(i+1) Cr(i)
11: Mode3 Y(i) Cr(i) Y(i+1) Cb(i)
This is based on a sensor format set to CbYCrY (UYVY). The driver
hardcodes the output memory format to YUYV, configure the ordering
accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
ISI_MCK is the sensor master clock. It should be handled by the sensor
driver directly, as the ISI has no use for that clock. Make the clock
optional here while platforms transition to the correct model.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The queue setup operation isn't the right place to reset the ISI. Move
the reset call to the start streaming operation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The PCLK and MCK clocks are prepared and unprepared at probe and remove
time. Clock (un)preparation isn't needed before enabling/disabling the
clocks, and the enable/disable operation happen in non-atomic context.
We can thus defer (un)preparation to enable/disable time.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
when a userspace applications calls the VIDIOC_STREAMON ioctl. The
V4L2 core calls the soc_camera_streamon function, which is responsible
for starting the video stream. It does so by first starting the atmel-isi
host by a call to the vb2_streamon function, and then starting the sensor
by a call to the video.s_stream sensor subdev operation.
That means we wait for a SOF in start_streaming() before call sensor's
s_stream(). It is possible no VSYNC interrupt arrive as the sensor
hasn't been started yet.
To avoid such case, this patch remove the code to wait for the VSYNC
interrupt. And such code is not necessary.
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Print the PN value, useful to check what chip the dev board has.
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
si4713_set_rds_radio_text will overwrite the terminating zero at the
end of the rds radio text string in order to send out a carriage return
as per the RDS spec.
Use a separate char buffer for the CR instead of corrupting the control
string.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Eduardo Valentin <edubezval@gmail.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The supply list is needed by the platform driver, but not by the usb driver.
So this information belongs to the platform data and should not be hardcoded
in the subdevice driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Eduardo Valentin <edubezval@gmail.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is the USB driver for the Silicon Labs development board.
It contains the Si4713 FM transmitter chip.
Signed-off-by: Dinesh Ram <dinesh.ram@cern.ch>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Eduardo Valentin <edubezval@gmail.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The Si4713 development board contains a Si4713 FM transmitter chip
and is handled by the radio-usb-si4713 driver.
The board reports itself as (10c4:8244) Cygnal Integrated Products, Inc.
and misidentifies itself as a HID device in its USB interface descriptor.
This patch ignores this device as an HID device and hence loads the custom driver.
Signed-off-by: Dinesh Ram <dinesh.ram@cern.ch>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Eduardo Valentin <edubezval@gmail.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In the si4713_tx_tune_power() method, the args array element 'power'
can take values between SI4713_MIN_POWER and SI4713_MAX_POWER. power = 0
is also valid. All the values (0 > power < SI4713_MIN_POWER) are illegal
and hence are all mapped to SI4713_MIN_POWER.
Signed-off-by: Dinesh Ram <dinesh.ram@cern.ch>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Eduardo Valentin <edubezval@gmail.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Checks have been introduced at several places in the code to test if an
interrupt is set or not. For devices which do not use the interrupt, to
get a valid response, within a specified timeout, the device is polled
instead.
Signed-off-by: Dinesh Ram <dinesh.ram@cern.ch>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Eduardo Valentin <edubezval@gmail.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Added a new si4713 directory which will contain all si4713 related files.
Also updated Makefile and Kconfig
Signed-off-by: Dinesh Ram <dinesh.ram@cern.ch>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Eduardo Valentin <edubezval@gmail.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Rewrite the return statement in vpfe_video.c. This will prevent
the checkpatch.pl script from generating a warning saying
to remove () from this particular return statement.
Signed-off-by: Lisa Nguyen <lisa@xenapiadmin.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The v4l2_of_get_remote_port() function acquires a reference to an
endpoint node through a phandle and then returns the node's parent,
without dropping the reference to the endpoint node. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The field isn't set when parsing the endpoint. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When CONFIG_OF is not defined the v4l2_of_parse_endpoint() function is
defined as a stub that returns -ENOSYS. Make the real function return an
integer as well to be able to differentiate between the two cases.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
A missing break resulted in all done buffers being flagged with
V4L2_BUF_FLAG_QUEUED. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Replace devm_request_mem_region() and devm_ioremap_nocache() with
devm_ioremap_resource(). The behaviour remains the same and the code is
simplified.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The clock core code is going to be modified so clk_get() takes
reference on the clock provider module. Until the potential circular
reference issue is properly addressed, we pass NULL as the first
argument to clk_register(), in order to disallow sub-devices taking
a reference on the ISP module back trough clk_get(). This should
prevent locking the modules in memory.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds proper initialization of the in-driver
cached state of JPEG controls with V4L2 core.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
s5p_jpeg_device_run and s5p_jpeg_runtime_resume callbacks should
have spin_lock protection as they alter device registers.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Standard suspend/resume path is called after runtime resume
of the given device, so suspend/resume callbacks must do all
clock management done also by runtime pm to allow for proper
power domain shutdown. Moreover, JPEG clock is enabled from
probe function but is is not necessary. This patch also moves
control of jpeg clock to runtime_pm callbacks.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Aligning capture queue image dimensions while enqueuing output
queue doesn't make a sense as the S_FMT ioctl might have not
been called for the capture queue until that moment, whereas
it is required to know capture format as the type of alignment
heavily depends on it.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The aim of the condition is ensuring that the bytesperline
value set by the user space application is proper for the
given format and adjusting it if isn't. As the depth value
of the format description entry is expressed in bits then
the bytesperline value needs to be divided, not multiplied,
by that value to get the number of bytes required to store
single line of image samples.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Output samples during decoding phase for the YUV 4:2:0 format
are arranged in the manner compatible with 2-planar NV12,
not 3-planar YUV420 fourcc.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reorder quantization tables so that their elements
are arranged in the manner reflecting compression
quality level that is in accordance with V4L2 documentation,
i.e. the larger value of the V4L2_CID_JPEG_COMPRESSION_QUALITY
control the better image quality, and thus lower compression
quality. The modification allows also to get rid of
reverse logic in the s_ctrl callback while assigning
user space value to the ctx->compr_quality variable.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch enables the JPEG codec on S5PV210 and Exynos4210 SoCs. There are
some differences in newer versions of the JPEG codec IP on SoCs like Exynos4x12
and Exynos5 series and support for them will be added in subsequent patches.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
It is hard to distinguish between decoder and encoder video device
because their names are same. So this patch fixes the names.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Merge the media fixes merged upstream for v3.13-rc4
* upstream-fixes: (30 commits)
[media] videobuf2-dma-sg: fix possible memory leak
[media] vb2: regression fix: always set length field.
[media] mt9p031: Include linux/of.h header
[media] rtl2830: add parent for I2C adapter
[media] media: marvell-ccic: use devm to release clk
[media] ths7303: Declare as static a private function
[media] em28xx-video: Swap release order to avoid lock nesting
[media] usbtv: Add support for PAL video source
[media] media_tree: Fix spelling errors
[media] videobuf2: Add support for file access mode flags for DMABUF exporting
[media] radio-shark2: Mark shark_resume_leds() inline to kill compiler warning
[media] radio-shark: Mark shark_resume_leds() inline to kill compiler warning
[media] af9035: unlock on error in af9035_i2c_master_xfer()
[media] af9033: fix broken I2C
[media] v4l: omap3isp: Don't check for missing get_fmt op on remote subdev
[media] af9035: fix broken I2C and USB I/O
[media] wm8775: fix broken audio routing
[media] marvell-ccic: drop resource free in driver remove
[media] tef6862/radio-tea5764: actually assign clamp result
[media] cx231xx: use after free on error path in probe
...
The Look-Up Table looks up values in 8-bit indexed tables separately for
each color component.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The Super Resolution Unit performs super resolution processing with
optional upscaling by a factor of two.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The Hue Saturation value Transform and Hue Saturation value Inverse
transform entities convert from RGB to HSV and back.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Implement the get and set selection operations on the RPF and WPF
entities. Only the crop targets are currently available.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When operating in DU output mode (deep pipeline to the DU through the
LIF), the VSP1 needs to constantly supply frames to the display. To
ensure reuse the last queued buffer instead of returning it to the user.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The MT9V034 sensor is very similar to the MT9V032, with a couple of
different registers and parameters.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
To prepare support of the MT9V034, add the necessary infrastructure to
support model-specific parameters.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Identify the model based on the I2C device name and configure formats
accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The sensor can scale the image down using binning by 1, 2 or 4 in both
directions. Update size enumeration and ratio and binning factor
computation accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The active pixel array size is 753x481 with 4 additional black rows at
the top. Fix the driver accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The comment explaining the usage of the bypass bit is wrong, fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Laurent Pinchart
Josh Wu
Hans Verkuil
Eduardo Valentin
Dinesh Ram
Lisa Nguyen
Sylwester Nawrocki
Jacek Anaszewski
Seung-Woo Kim
Mauro Carvalho Chehab
Laurent Pinchart