In preparation for the OGMv2 packet aggregation, hold OGMv2 packets for
up to BATADV_MAX_AGGREGATION_MS milliseconds (100ms) on per
hard-interface queues, before transmitting.
This allows us to later squash multiple OGMs into a single frame
and transmission for reduced overhead.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Wire up the new clone3 syscall.
A fix for the PAPR SCM nvdimm driver, to fix a crash when firmware gives us a
device that's attached to a non-online NUMA node.
A fix for a boot failure on 32-bit with KASAN enabled.
Three fixes for implicit fall through warnings, some of which are errors for us
due to -Werror.
Thanks to:
Aneesh Kumar K.V, Christophe Leroy, Kees Cook, Santosh Sivaraj, Stephen
Rothwell.
-----BEGIN PGP SIGNATURE-----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=WT8n
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.3-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Some more powerpc fixes for 5.3:
- Wire up the new clone3 syscall.
- A fix for the PAPR SCM nvdimm driver, to fix a crash when firmware
gives us a device that's attached to a non-online NUMA node.
- A fix for a boot failure on 32-bit with KASAN enabled.
- Three fixes for implicit fall through warnings, some of which are
errors for us due to -Werror.
Thanks to: Aneesh Kumar K.V, Christophe Leroy, Kees Cook, Santosh
Sivaraj, Stephen Rothwell"
* tag 'powerpc-5.3-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/kasan: fix early boot failure on PPC32
drivers/macintosh/smu.c: Mark expected switch fall-through
powerpc/spe: Mark expected switch fall-throughs
powerpc/nvdimm: Pick nearby online node if the device node is not online
powerpc/kvm: Fall through switch case explicitly
powerpc: Wire up clone3 syscall
At the end of the v5.3 upstream kernel development cycle, Simon will be
stepping down from his role as Renesas SoC maintainer. Starting with
the v5.4 development cycle, Geert is taking over this role.
Add Geert as a co-maintainer, and add his git repository and branch.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- detect missing missing "WITH Linux-syscall-note" for uapi headers
- fix needless rebuild when using Clang
- fix false-positive cc-option in Kconfig when using Clang
- avoid including corrupted .*.cmd files in the modpost stage
- fix warning of 'make vmlinux'
- fix {m,n,x,g}config to not generate the broken .config on the second
save operation.
- some trivial Makefile fixes
-----BEGIN PGP SIGNATURE-----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=QEIS
-----END PGP SIGNATURE-----
Merge tag 'kbuild-fixes-v5.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- detect missing missing "WITH Linux-syscall-note" for uapi headers
- fix needless rebuild when using Clang
- fix false-positive cc-option in Kconfig when using Clang
- avoid including corrupted .*.cmd files in the modpost stage
- fix warning of 'make vmlinux'
- fix {m,n,x,g}config to not generate the broken .config on the second
save operation.
- some trivial Makefile fixes
* tag 'kbuild-fixes-v5.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kconfig: Clear "written" flag to avoid data loss
kbuild: Check for unknown options with cc-option usage in Kconfig and clang
lib/raid6: fix unnecessary rebuild of vpermxor*.c
kbuild: modpost: do not parse unnecessary rules for vmlinux modpost
kbuild: modpost: remove unnecessary dependency for __modpost
kbuild: modpost: handle KBUILD_EXTRA_SYMBOLS only for external modules
kbuild: modpost: include .*.cmd files only when targets exist
kbuild: initialize CLANG_FLAGS correctly in the top Makefile
kbuild: detect missing "WITH Linux-syscall-note" for uapi headers
Has not had any bake time or testing, since its just changes to a text file.
-----BEGIN PGP SIGNATURE-----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=bvqJ
-----END PGP SIGNATURE-----
Merge tag 'safesetid-maintainers-correction-5.3-rc2' of git://github.com/micah-morton/linux
Pull SafeSetID maintainer update from Micah Morton:
"Add entry in MAINTAINERS file for SafeSetID LSM"
* tag 'safesetid-maintainers-correction-5.3-rc2' of git://github.com/micah-morton/linux:
Add entry in MAINTAINERS file for SafeSetID LSM
Fix assignment of the FM10K_FAULT_ADDR_LO register into fault->address
by using a bit-wise |= operation. Without this, the low address is
completely overwriting the high potion of the address. This caused the
fault to incorrectly return only the lower 32 bits of the fault address.
This issue was detected by cppcheck and resolves the following warnings
produced by that tool:
[fm10k_pf.c:1668] -> [fm10k_pf.c:1670]: (style) Variable
'fault->address' is reassigned a value before the old one has been used.
[fm10k_pf.c:1669] -> [fm10k_pf.c:1670]: (style) Variable
'fault->address' is reassigned a value before the old one has been used.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver currently uses a macro to decide whether we should use
NON_Q_VECTORS_PF or NON_Q_VECTORS_VF.
However, we also define NON_Q_VECTORS_VF to the same value as
NON_Q_VECTORS_PF. This means that the macro NON_Q_VECTORS(hw) will
always return the same value.
Let's just remove this macro, and replace it directly with an enum value
on the enum non_q_vectors.
This was detected by cppcheck and fixes the following warnings when
building with BUILD=KERNEL
[fm10k_ethtool.c:1123]: (style) Same value in both branches of ternary
operator.
[fm10k_ethtool.c:1142]: (style) Same value in both branches of ternary
operator.
[fm10k_main.c:1826]: (style) Same value in both branches of ternary
operator.
[fm10k_main.c:1849]: (style) Same value in both branches of ternary
operator.
[fm10k_main.c:1858]: (style) Same value in both branches of ternary
operator.
[fm10k_pci.c:901]: (style) Same value in both branches of ternary
operator.
[fm10k_pci.c:1040]: (style) Same value in both branches of ternary
operator.
[fm10k_pci.c:1726]: (style) Same value in both branches of ternary
operator.
[fm10k_pci.c:1763]: (style) Same value in both branches of ternary
operator.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Several functions in the fm10k driver have specific function templates,
as they are used as function pointers. The parameters in these functions
are not always used. Explicitly mark unused parameters with the
__always_unused macro, so that the compiler will not warn about them
when building with the -Wunused-parameter warning enabled.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The page_addr variable is a void pointer. Incrementing it before calling
prefetch is technically undefined. Fix this by casting it to a u8*
pointer before incrementing it. This ensures that we increment the
pointer value in byte units, instead of relying on this undefined
behavior.
This was detected by cppcheck, and resolves the following warning
produced by that tool:
[fm10k_main.c:328]: (portability) 'page_addr' is of type 'void *'. When
using void pointers in calculations, the behaviour is undefined.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the fm10k_handle_resume function, return 0 explicitly at the end of
the function instead of returning the err value.
This was detected by cppcheck and resolves the following style warning
produced by that tool:
[fm10k_pci.c:2768] -> [fm10k_pci.c:2787]: (warning) Identical condition
'err', second condition is always false
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The local variable 'size' in fm10k_dfwd_add_station is initialized, but
is always re-assigned immediately before use. Remove this unnecessary
initialization.
This was detected by cppcheck and resolves the following warning
produced by that tool:
[fm10k_netdev.c:1466]: (style) Variable 'size' is assigned a value that is never used.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The local variable err in several functions in the fm10k_netdev.c file
is initialized with a value that is never used. The err value is
immediately re-assigned in all cases where it will be checked. Remove
the unnecessary initializers.
This was detected by cppcheck and resolves the following warnings
produced by that tool:
[fm10k_netdev.c:999] -> [fm10k_netdev.c:1004]: (style) Variable 'err' is
reassigned a value before the old one has been used.
[fm10k_netdev.c:1019] -> [fm10k_netdev.c:1024]: (style) Variable 'err'
is reassigned a value before the old one has been used.
[fm10k_netdev.c:64]: (style) Variable 'err' is assigned a value that is
never used.
[fm10k_netdev.c:131]: (style) Variable 'err' is assigned a value that
is never used.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The err variable in the fm10k_tlv_attr_parse function is initialized
with zero. However, the function never reads err without first assigning
it from a function call. Remove this unnecessary initialization.
This was detected by cppcheck and resolves the following warning
produced by that tool:
[fm10k_tlv.c:498]: (style) Variable 'err' is assigned a value that is
never used.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Prior to this commit, starting nconfig, xconfig or gconfig, and saving
the .config file more than once caused data loss, where a .config file
that contained only comments would be written to disk starting from the
second save operation.
This bug manifests itself because the SYMBOL_WRITTEN flag is never
cleared after the first call to conf_write, and subsequent calls to
conf_write then skip all of the configuration symbols due to the
SYMBOL_WRITTEN flag being set.
This commit resolves this issue by clearing the SYMBOL_WRITTEN flag
from all symbols before conf_write returns.
Fixes: 8e2442a5f8 ("kconfig: fix missing choice values in auto.conf")
Cc: linux-stable <stable@vger.kernel.org> # 4.19+
Signed-off-by: M. Vefa Bicakci <m.v.b@runbox.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
- fix build for xtensa cores with coprocessors that was broken by
entry/return abstraction patch.
-----BEGIN PGP SIGNATURE-----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=QOUM
-----END PGP SIGNATURE-----
Merge tag 'xtensa-20190803' of git://github.com/jcmvbkbc/linux-xtensa
Pull Xtensa fix from Max Filippov:
"Fix build for xtensa cores with coprocessors that was broken by
entry/return abstraction patch"
* tag 'xtensa-20190803' of git://github.com/jcmvbkbc/linux-xtensa:
xtensa: fix build for cores with coprocessors
Pull i2c fixes from Wolfram Sang:
"A set of driver fixes for the I2C subsystem"
* 'i2c/for-current-fixed' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: s3c2410: Mark expected switch fall-through
i2c: at91: fix clk_offset for sama5d2
i2c: at91: disable TXRDY interrupt after sending data
i2c: iproc: Fix i2c master read more than 63 bytes
eeprom: at24: make spd world-readable again
Add documentation to the Spectre document about the new swapgs variant of
Spectre v1.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
There are a lot of those warnings with GCC8+ 64-bit,
In file included from ./include/linux/sctp.h:42,
from net/core/skbuff.c:47:
./include/uapi/linux/sctp.h:395:1: warning: alignment 4 of 'struct
sctp_paddr_change' is less than 8 [-Wpacked-not-aligned]
} __attribute__((packed, aligned(4)));
^
./include/uapi/linux/sctp.h:728:1: warning: alignment 4 of 'struct
sctp_setpeerprim' is less than 8 [-Wpacked-not-aligned]
} __attribute__((packed, aligned(4)));
^
./include/uapi/linux/sctp.h:727:26: warning: 'sspp_addr' offset 4 in
'struct sctp_setpeerprim' isn't aligned to 8 [-Wpacked-not-aligned]
struct sockaddr_storage sspp_addr;
^~~~~~~~~
./include/uapi/linux/sctp.h:741:1: warning: alignment 4 of 'struct
sctp_prim' is less than 8 [-Wpacked-not-aligned]
} __attribute__((packed, aligned(4)));
^
./include/uapi/linux/sctp.h:740:26: warning: 'ssp_addr' offset 4 in
'struct sctp_prim' isn't aligned to 8 [-Wpacked-not-aligned]
struct sockaddr_storage ssp_addr;
^~~~~~~~
./include/uapi/linux/sctp.h:792:1: warning: alignment 4 of 'struct
sctp_paddrparams' is less than 8 [-Wpacked-not-aligned]
} __attribute__((packed, aligned(4)));
^
./include/uapi/linux/sctp.h:784:26: warning: 'spp_address' offset 4 in
'struct sctp_paddrparams' isn't aligned to 8 [-Wpacked-not-aligned]
struct sockaddr_storage spp_address;
^~~~~~~~~~~
./include/uapi/linux/sctp.h:905:1: warning: alignment 4 of 'struct
sctp_paddrinfo' is less than 8 [-Wpacked-not-aligned]
} __attribute__((packed, aligned(4)));
^
./include/uapi/linux/sctp.h:899:26: warning: 'spinfo_address' offset 4
in 'struct sctp_paddrinfo' isn't aligned to 8 [-Wpacked-not-aligned]
struct sockaddr_storage spinfo_address;
^~~~~~~~~~~~~~
This is because the commit 20c9c825b1 ("[SCTP] Fix SCTP socket options
to work with 32-bit apps on 64-bit kernels.") added "packed, aligned(4)"
GCC attributes to some structures but one of the members, i.e, "struct
sockaddr_storage" in those structures has the attribute,
"aligned(__alignof__ (struct sockaddr *)" which is 8-byte on 64-bit
systems, so the commit overwrites the designed alignments for
"sockaddr_storage".
To fix this, "struct sockaddr_storage" needs to be aligned to 4-byte as
it is only used in those packed sctp structure which is part of UAPI,
and "struct __kernel_sockaddr_storage" is used in some other
places of UAPI that need not to change alignments in order to not
breaking userspace.
Use an implicit alignment for "struct __kernel_sockaddr_storage" so it
can keep the same alignments as a member in both packed and un-packed
structures without breaking UAPI.
Suggested-by: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Qian Cai <cai@lca.pw>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull perf tooling fixes from Thomas Gleixner:
"A set of updates for perf tools and documentation:
perf header:
- Prevent a division by zero
- Deal with an uninitialized warning proper
libbpf:
- Fix the missiong __WORDSIZE definition for musl & al
UAPI headers:
- Synchronize kernel headers
Documentation:
- Fix the memory units for perf.data size"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
libbpf: fix missing __WORDSIZE definition
perf tools: Fix perf.data documentation units for memory size
perf header: Fix use of unitialized value warning
perf header: Fix divide by zero error if f_header.attr_size==0
tools headers UAPI: Sync if_link.h with the kernel
tools headers UAPI: Sync sched.h with the kernel
tools headers UAPI: Sync usbdevice_fs.h with the kernels to get new ioctl
tools perf beauty: Fix usbdevfs_ioctl table generator to handle _IOC()
tools headers UAPI: Update tools's copy of drm.h headers
tools headers UAPI: Update tools's copy of mman.h headers
tools headers UAPI: Update tools's copy of kvm.h headers
tools include UAPI: Sync x86's syscalls_64.tbl and generic unistd.h to pick up clone3 and pidfd_open
Pull vdso timer fixes from Thomas Gleixner:
"A series of commits to deal with the regression caused by the generic
VDSO implementation.
The usage of clock_gettime64() for 32bit compat fallback syscalls
caused seccomp filters to kill innocent processes because they only
allow clock_gettime().
Handle the compat syscalls with clock_gettime() as before, which is
not a functional problem for the VDSO as the legacy compat application
interface is not y2038 safe anyway. It's just extra fallback code
which needs to be implemented on every architecture.
It's opt in for now so that it does not break the compile of already
converted architectures in linux-next. Once these are fixed, the
#ifdeffery goes away.
So much for trying to be smart and reuse code..."
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
arm64: compat: vdso: Use legacy syscalls as fallback
x86/vdso/32: Use 32bit syscall fallback
lib/vdso/32: Provide legacy syscall fallbacks
lib/vdso: Move fallback invocation to the callers
lib/vdso/32: Remove inconsistent NULL pointer checks
Pull irq fixes from Thomas Gleixner:
"A small bunch of fixes from the irqchip department:
- Fix a couple of UAF on error paths (RZA1, GICv3 ITS)
- Fix iMX GPCv2 trigger setting
- Add missing of_node_put() on error path in MBIGEN
- Add another bunch of /* fall-through */ to silence warnings"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/renesas-rza1: Fix an use-after-free in rza1_irqc_probe()
irqchip/irq-imx-gpcv2: Forward irq type to parent
irqchip/irq-mbigen: Add of_node_put() before return
irqchip/gic-v3-its: Free unused vpt_page when alloc vpe table fail
irqchip/gic-v3: Mark expected switch fall-through
Pull xfs fixes from Darrick Wong:
- Avoid leaking kernel stack contents to userspace
- Fix a potential null pointer dereference in the dabtree scrub code
* tag 'xfs-5.3-fixes-1' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: Fix possible null-pointer dereferences in xchk_da_btree_block_check_sibling()
xfs: fix stack contents leakage in the v1 inumber ioctls
David Ahern says:
====================
net: Add functional tests for L3 and L4
This is a port the functional test cases created during the development
of the VRF feature. It covers various permutations of icmp, tcp and udp
for IPv4 and IPv6 including negative tests.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add use case section to fcnal-test.
Initial test is VRF based with a bridge and vlans. The commands
stem from bug reports fixed by:
a173f066c7 ("netfilter: bridge: Don't sabotage nf_hook calls from an l3mdev")
cd6428988b ("netfilter: bridge: Don't sabotage nf_hook calls for an l3mdev slave")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IPv6 netfilter tests to send tcp reset or icmp unreachable for a
port. Initial tests are VRF only.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add netfilter tests to send tcp reset or icmp unreachable for a port.
Initial tests are VRF only.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IPv6 runtime tests where passive (no traffic flowing) and active
(with traffic) sockets are expected to be reset on device deletes.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add runtime tests where passive (no traffic flowing) and active (with
traffic) sockets are expected to be reset on device deletes.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IPv6 address bind tests to fcnal-test.sh. Verifies socket binding to
local addresses for raw, tcp and udp including device and VRF cases.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add address bind tests to fcnal-test.sh. Verifies socket binding to
local addresses for raw, tcp and udp including device and VRF cases.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IPv6 udp tests to fcnal-test.sh. Covers the permutations of directly
connected addresses, routed destinations, VRF and non-VRF, and expected
failures for both clients and servers. Includes permutations with
net.ipv4.udp_l3mdev_accept set to 0 and 1.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add udp tests to fcnal-test.sh. Covers the permutations of directly
connected addresses, routed destinations, VRF and non-VRF, and expected
failures for both clients and servers. Includes permutations with
net.ipv4.udp_l3mdev_accept set to 0 and 1.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IPv6 tcp tests to fcnal-test.sh. Covers the permutations of directly
connected addresses, routed destinations, VRF and non-VRF, and expected
failures for both clients and servers. Includes permutations with
net.ipv4.tcp_l3mdev_accept set to 0 and 1.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add tcp tests to fcnal-test.sh. Covers the permutations of directly
connected addresses, routed destinations, VRF and non-VRF, and expected
failures for both clients and servers. Includes permutations with
net.ipv4.tcp_l3mdev_accept set to 0 and 1.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IPv6 ping tests to fcnal-test.sh. Covers the permutations of directly
connected addresses, routed destinations, VRF and non-VRF, and expected
failures.
Setup includes unreachable routes and fib rules blocking traffic.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ping tests to fcnal-test.sh. Covers the permutations of directly
connected addresses, routed destinations, VRF and non-VRF, and expected
failures.
Setup includes unreachable routes and fib rules blocking traffic.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initial commit for functional test suite for fib and socket lookups.
This commit contains the namespace setup, networking config, test options
and other basic infrastructure.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add nettest - a simple program with an implementation for various networking
APIs. nettest is used for tcp, udp and raw functional tests for both IPv4
and IPv6.
Point of this command versus existing utilities:
- controlled implementation of the APIs and the order in which they
are called,
- ability to verify ingress device, local and remote addresses,
- timeout for controlled test length,
- ability to discriminate a timeout from a system call failure, and
- simplicity with test scripts.
The command returns:
0 on success,
1 for any system call failure, and
2 on timeout.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2019-08-01
This series for fm10k, by Jake Keller, reduces the scope of local variables
where possible.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge misc fixes from Andrew Morton:
"17 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
drivers/acpi/scan.c: document why we don't need the device_hotplug_lock
memremap: move from kernel/ to mm/
lib/test_meminit.c: use GFP_ATOMIC in RCU critical section
asm-generic: fix -Wtype-limits compiler warnings
cgroup: kselftest: relax fs_spec checks
mm/memory_hotplug.c: remove unneeded return for void function
mm/migrate.c: initialize pud_entry in migrate_vma()
coredump: split pipe command whitespace before expanding template
page flags: prioritize kasan bits over last-cpuid
ubsan: build ubsan.c more conservatively
kasan: remove clang version check for KASAN_STACK
mm: compaction: avoid 100% CPU usage during compaction when a task is killed
mm: migrate: fix reference check race between __find_get_block() and migration
mm: vmscan: check if mem cgroup is disabled or not before calling memcg slab shrinker
ocfs2: remove set but not used variable 'last_hash'
Revert "kmemleak: allow to coexist with fault injection"
kernel/signal.c: fix a kernel-doc markup
Three minor RISC-V-related changes for v5.3-rc3:
- Add build ID to VDSO builds to avoid a double-free in perf when
libelf isn't used
- Align the RV64 defconfig to the output of "make savedefconfig" so
subsequent defconfig patches don't get out of hand
- Drop a superfluous DT property from the FU540 SoC DT data (since it
must be already set in board data that includes it)
-----BEGIN PGP SIGNATURE-----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=CIhE
-----END PGP SIGNATURE-----
Merge tag 'riscv/for-v5.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Paul Walmsley:
"Three minor RISC-V-related changes for v5.3-rc3:
- Add build ID to VDSO builds to avoid a double-free in perf when
libelf isn't used
- Align the RV64 defconfig to the output of "make savedefconfig" so
subsequent defconfig patches don't get out of hand
- Drop a superfluous DT property from the FU540 SoC DT data (since it
must be already set in board data that includes it)"
* tag 'riscv/for-v5.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: defconfig: align RV64 defconfig to the output of "make savedefconfig"
riscv: dts: fu540-c000: drop "timebase-frequency"
riscv: Fix perf record without libelf support
Let's document why the lock is not needed in acpi_scan_init(), right now
this is not really obvious.
[akpm@linux-foundation.org: fix tpyo]
Link: http://lkml.kernel.org/r/20190731135306.31524-1-david@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Oscar Salvador <osalvador@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
memremap.c implements MM functionality for ZONE_DEVICE, so it really
should be in the mm/ directory, not the kernel/ one.
Link: http://lkml.kernel.org/r/20190722094143.18387-1-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
kmalloc() shouldn't sleep while in RCU critical section, therefore use
GFP_ATOMIC instead of GFP_KERNEL.
The bug was spotted by the 0day kernel testing robot.
Link: http://lkml.kernel.org/r/20190725121703.210874-1-glider@google.com
Fixes: 7e659650cbda ("lib: introduce test_meminit module")
Signed-off-by: Alexander Potapenko <glider@google.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit d66acc39c7 ("bitops: Optimise get_order()") introduced a
compilation warning because "rx_frag_size" is an "ushort" while
PAGE_SHIFT here is 16.
The commit changed the get_order() to be a multi-line macro where
compilers insist to check all statements in the macro even when
__builtin_constant_p(rx_frag_size) will return false as "rx_frag_size"
is a module parameter.
In file included from ./arch/powerpc/include/asm/page_64.h:107,
from ./arch/powerpc/include/asm/page.h:242,
from ./arch/powerpc/include/asm/mmu.h:132,
from ./arch/powerpc/include/asm/lppaca.h:47,
from ./arch/powerpc/include/asm/paca.h:17,
from ./arch/powerpc/include/asm/current.h:13,
from ./include/linux/thread_info.h:21,
from ./arch/powerpc/include/asm/processor.h:39,
from ./include/linux/prefetch.h:15,
from drivers/net/ethernet/emulex/benet/be_main.c:14:
drivers/net/ethernet/emulex/benet/be_main.c: In function 'be_rx_cqs_create':
./include/asm-generic/getorder.h:54:9: warning: comparison is always
true due to limited range of data type [-Wtype-limits]
(((n) < (1UL << PAGE_SHIFT)) ? 0 : \
^
drivers/net/ethernet/emulex/benet/be_main.c:3138:33: note: in expansion
of macro 'get_order'
adapter->big_page_size = (1 << get_order(rx_frag_size)) * PAGE_SIZE;
^~~~~~~~~
Fix it by moving all of this multi-line macro into a proper function,
and killing __get_order() off.
[akpm@linux-foundation.org: remove __get_order() altogether]
[cai@lca.pw: v2]
Link: http://lkml.kernel.org/r/1564000166-31428-1-git-send-email-cai@lca.pw
Link: http://lkml.kernel.org/r/1563914986-26502-1-git-send-email-cai@lca.pw
Fixes: d66acc39c7 ("bitops: Optimise get_order()")
Signed-off-by: Qian Cai <cai@lca.pw>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: David Howells <dhowells@redhat.com>
Cc: Jakub Jelinek <jakub@redhat.com>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Bill Wendling <morbo@google.com>
Cc: James Y Knight <jyknight@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On my laptop most memcg kselftests were being skipped because it claimed
cgroup v2 hierarchy wasn't mounted, but this isn't correct. Instead, it
seems current systemd HEAD mounts it with the name "cgroup2" instead of
"cgroup":
% grep cgroup /proc/mounts
cgroup2 /sys/fs/cgroup cgroup2 rw,nosuid,nodev,noexec,relatime,nsdelegate 0 0
I can't think of a reason to need to check fs_spec explicitly
since it's arbitrary, so we can just rely on fs_vfstype.
After these changes, `make TARGETS=cgroup kselftest` actually runs the
cgroup v2 tests in more cases.
Link: http://lkml.kernel.org/r/20190723210737.GA487@chrisdown.name
Signed-off-by: Chris Down <chris@chrisdown.name>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Roman Gushchin <guro@fb.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
return is unneeded in void function
Link: http://lkml.kernel.org/r/20190723130814.21826-1-houweitaoo@gmail.com
Signed-off-by: Weitao Hou <houweitaoo@gmail.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When CONFIG_MIGRATE_VMA_HELPER is enabled, migrate_vma() calls
migrate_vma_collect() which initializes a struct mm_walk but didn't
initialize mm_walk.pud_entry. (Found by code inspection) Use a C
structure initialization to make sure it is set to NULL.
Link: http://lkml.kernel.org/r/20190719233225.12243-1-rcampbell@nvidia.com
Fixes: 8763cb45ab ("mm/migrate: new memory migration helper for use with device memory")
Signed-off-by: Ralph Campbell <rcampbell@nvidia.com>
Reviewed-by: John Hubbard <jhubbard@nvidia.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: "Jérôme Glisse" <jglisse@redhat.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Save the offsets of the start of each argument to avoid having to update
pointers to each argument after every corename krealloc and to avoid
having to duplicate the memory for the dump command.
Executable names containing spaces were previously being expanded from
%e or %E and then split in the middle of the filename. This is
incorrect behaviour since an argument list can represent arguments with
spaces.
The splitting could lead to extra arguments being passed to the core
dump handler that it might have interpreted as options or ignored
completely.
Core dump handlers that are not aware of this Linux kernel issue will be
using %e or %E without considering that it may be split and so they will
be vulnerable to processes with spaces in their names breaking their
argument list. If their internals are otherwise well written, such as
if they are written in shell but quote arguments, they will work better
after this change than before. If they are not well written, then there
is a slight chance of breakage depending on the details of the code but
they will already be fairly broken by the split filenames.
Core dump handlers that are aware of this Linux kernel issue will be
placing %e or %E as the last item in their core_pattern and then
aggregating all of the remaining arguments into one, separated by
spaces. Alternatively they will be obtaining the filename via other
methods. Both of these will be compatible with the new arrangement.
A side effect from this change is that unknown template types (for
example %z) result in an empty argument to the dump handler instead of
the argument being dropped. This is a desired change as:
It is easier for dump handlers to process empty arguments than dropped
ones, especially if they are written in shell or don't pass each
template item with a preceding command-line option in order to
differentiate between individual template types. Most core_patterns in
the wild do not use options so they can confuse different template types
(especially numeric ones) if an earlier one gets dropped in old kernels.
If the kernel introduces a new template type and a core_pattern uses it,
the core dump handler might not expect that the argument can be dropped
in old kernels.
For example, this can result in security issues when %d is dropped in
old kernels. This happened with the corekeeper package in Debian and
resulted in the interface between corekeeper and Linux having to be
rewritten to use command-line options to differentiate between template
types.
The core_pattern for most core dump handlers is written by the handler
author who would generally not insert unknown template types so this
change should be compatible with all the core dump handlers that exist.
Link: http://lkml.kernel.org/r/20190528051142.24939-1-pabs3@bonedaddy.net
Fixes: 74aadce986 ("core_pattern: allow passing of arguments to user mode helper when core_pattern is a pipe")
Signed-off-by: Paul Wise <pabs3@bonedaddy.net>
Reported-by: Jakub Wilk <jwilk@jwilk.net> [https://bugs.debian.org/924398]
Reported-by: Paul Wise <pabs3@bonedaddy.net> [https://lore.kernel.org/linux-fsdevel/c8b7ecb8508895bf4adb62a748e2ea2c71854597.camel@bonedaddy.net/]
Suggested-by: Jakub Wilk <jwilk@jwilk.net>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ARM64 randdconfig builds regularly run into a build error, especially
when NUMA_BALANCING and SPARSEMEM are enabled but not SPARSEMEM_VMEMMAP:
#error "KASAN: not enough bits in page flags for tag"
The last-cpuid bits are already contitional on the available space, so
the result of the calculation is a bit random on whether they were
already left out or not.
Adding the kasan tag bits before last-cpuid makes it much more likely to
end up with a successful build here, and should be reliable for
randconfig at least, as long as that does not randomize NR_CPUS or
NODES_SHIFT but uses the defaults.
In order for the modified check to not trigger in the x86 vdso32 code
where all constants are wrong (building with -m32), enclose all the
definitions with an #ifdef.
[arnd@arndb.de: build fix]
Link: http://lkml.kernel.org/r/CAK8P3a3Mno1SWTcuAOT0Wa9VS15pdU6EfnkxLbDpyS55yO04+g@mail.gmail.com
Link: http://lkml.kernel.org/r/20190722115520.3743282-1-arnd@arndb.de
Link: https://lore.kernel.org/lkml/20190618095347.3850490-1-arnd@arndb.de/
Fixes: 2813b9c029 ("kasan, mm, arm64: tag non slab memory allocated via pagealloc")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Andrey Konovalov <andreyknvl@google.com>
Reviewed-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Andrey Konovalov <andreyknvl@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
