TCP_BASE_MSS is used as the default initial MSS value when MTU probing is
enabled. Update the comment to reflect this.
Suggested-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Josh Hunt <johunt@akamai.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current implementation of TCP MTU probing can considerably
underestimate the MTU on lossy connections allowing the MSS to get down to
48. We have found that in almost all of these cases on our networks these
paths can handle much larger MTUs meaning the connections are being
artificially limited. Even though TCP MTU probing can raise the MSS back up
we have seen this not to be the case causing connections to be "stuck" with
an MSS of 48 when heavy loss is present.
Prior to pushing out this change we could not keep TCP MTU probing enabled
b/c of the above reasons. Now with a reasonble floor set we've had it
enabled for the past 6 months.
The new sysctl will still default to TCP_MIN_SND_MSS (48), but gives
administrators the ability to control the floor of MSS probing.
Signed-off-by: Josh Hunt <johunt@akamai.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The size of the snapshot has to be the same as the size of the region,
therefore no need to pass it again during snapshot creation. Remove the
arg and use region->size instead.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting from commit d41a69f1d3 ("tcp: make tcp_sendmsg() aware of socket backlog")
loopback flows got hurt, because for each skb sent, the socket receives an
immediate ACK and sk_flush_backlog() causes extra work.
Intent was to not let the backlog grow too much, but we went a bit too far.
We can check the backlog every 16 skbs (about 1MB chunks)
to increase TCP over loopback performance by about 15 %
Note that the call to sk_flush_backlog() handles a single ACK,
thanks to coalescing done on backlog, but cleans the 16 skbs
found in rtx rb-tree.
Reported-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
octeon_mbox_process_cmd() directly writes the PCI_EXP_DEVCTL_BCR_FLR
bit, which bypasses timing requirements imposed by the PCIe spec.
This patch fixes the function to use the pcie_flr() interface instead.
Signed-off-by: Denis Efremov <efremov@linux.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We allocate 16kb per rx buffer, so we can avoid some overhead by using
alloc_pages_node directly instead of bothering kmalloc_node. Due to
this change buffers are page-aligned now, therefore the alignment check
can be removed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
net/sched/sch_fq_codel.c: In function fq_codel_dequeue:
net/sched/sch_fq_codel.c:288:23: warning: variable prev_ecn_mark set but not used [-Wunused-but-set-variable]
net/sched/sch_fq_codel.c:288:6: warning: variable prev_drop_count set but not used [-Wunused-but-set-variable]
They are not used since commit 77ddaff218 ("fq_codel: Kill
useless per-flow dropped statistic")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend existing driver for Spectrum and Spectrum-2 ASICs
to support Spectrum-3 ASIC as well.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu says:
====================
net: stmmac: Improvements for -next
[ This is just a rebase of v2 into latest -next in order to avoid a merge
conflict ]
Couple of improvements for -next tree. More info in commit logs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a selftest for the Flexible RX Parser feature.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
XGMAC cores also support the Flexible RX Parser feature. Add the support
for it in the XGMAC core.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
XGMAC also supports Safety Features. This patch implements the
configuration and handling of this feature in XGMAC core.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a selftest for VLAN and Double VLAN Filtering in stmmac.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the VLAN Hash Filtering feature in XGMAC core.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the RSS functionality and add the corresponding callbacks in
XGMAC core.
Changes from v1:
- Do not use magic constants (Jakub)
- Use ethtool_rxfh_indir_default() (Jakub)
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the TX Queue Priority callback in XGMAC core.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the TX Queue Weight callback. In order for this to be active
we also need to set ETS algorithm when configuring Queue.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the MMC counters feature in XGMAC core.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since node internal messages are passed directly to the socket, it is not
possible to observe those messages via tcpdump or wireshark.
We now remedy this by making it possible to clone such messages and send
the clones to the loopback interface. The clones are dropped at reception
and have no functional role except making the traffic visible.
The feature is enabled if network taps are active for the loopback device.
pcap filtering restrictions require the messages to be presented to the
receiving side of the loopback device.
v3 - Function dev_nit_active used to check for network taps.
- Procedure netif_rx_ni used to send cloned messages to loopback device.
Signed-off-by: John Rutherford <john.rutherford@dektech.com.au>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
wenxu says:
====================
flow_offload: add indr-block in nf_table_offload
This series patch make nftables offload support the vlan and
tunnel device offload through indr-block architecture.
The first four patches mv tc indr block to flow offload and
rename to flow-indr-block.
Because the new flow-indr-block can't get the tcf_block
directly. The fifth patch provide a callback list to get
flow_block of each subsystem immediately when the device
register and contain a block.
The last patch make nf_tables_offload support flow-indr-block.
This version add a mutex lock for add/del flow_indr_block_ing_cb
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
It provide a callback list to find the blocks of tc
and nft subsystems
Signed-off-by: wenxu <wenxu@ucloud.cn>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
move tc indirect block to flow_offload and rename
it to flow indirect block.The nf_tables can use the
indr block architecture.
Signed-off-by: wenxu <wenxu@ucloud.cn>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch make indr_block_call don't access struct tc_indr_block_cb
and tc_indr_block_dev directly
Signed-off-by: wenxu <wenxu@ucloud.cn>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the tcf_block in the tc_indr_block_dev for muti-subsystem
support.
Signed-off-by: wenxu <wenxu@ucloud.cn>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch make tc_indr_block_ing_cmd can't access struct
tc_indr_block_dev and tc_indr_block_cb.
Signed-off-by: wenxu <wenxu@ucloud.cn>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Edward Cree says:
====================
net: batched receive in GRO path
This series listifies part of GRO processing, in a manner which allows those
packets which are not GROed (i.e. for which dev_gro_receive returns
GRO_NORMAL) to be passed on to the listified regular receive path.
dev_gro_receive() itself is not listified, nor the per-protocol GRO
callback, since GRO's need to hold packets on lists under napi->gro_hash
makes keeping the packets on other lists awkward, and since the GRO control
block state of held skbs can refer only to one 'new' skb at a time.
Instead, when napi_frags_finish() handles a GRO_NORMAL result, stash the skb
onto a list in the napi struct, which is received at the end of the napi
poll or when its length exceeds the (new) sysctl net.core.gro_normal_batch.
Performance figures with this series, collected on a back-to-back pair of
Solarflare sfn8522-r2 NICs with 120-second NetPerf tests. In the stats,
sample size n for old and new code is 6 runs each; p is from a Welch t-test.
Tests were run both with GRO enabled and disabled, the latter simulating
uncoalesceable packets (e.g. due to IP or TCP options). The receive side
(which was the device under test) had the NetPerf process pinned to one CPU,
and the device interrupts pinned to a second CPU. CPU utilisation figures
(used in cases of line-rate performance) are summed across all CPUs.
net.core.gro_normal_batch was left at its default value of 8.
TCP 4 streams, GRO on: all results line rate (9.415Gbps)
net-next: 210.3% cpu
after #1: 181.5% cpu (-13.7%, p=0.031 vs net-next)
after #3: 196.7% cpu (- 8.4%, p=0.136 vs net-next)
TCP 4 streams, GRO off:
net-next: 8.017 Gbps
after #1: 7.785 Gbps (- 2.9%, p=0.385 vs net-next)
after #3: 7.604 Gbps (- 5.1%, p=0.282 vs net-next. But note *)
TCP 1 stream, GRO off:
net-next: 6.553 Gbps
after #1: 6.444 Gbps (- 1.7%, p=0.302 vs net-next)
after #3: 6.790 Gbps (+ 3.6%, p=0.169 vs net-next)
TCP 1 stream, GRO on, busy_read = 50: all results line rate
net-next: 156.0% cpu
after #1: 174.5% cpu (+11.9%, p=0.015 vs net-next)
after #3: 165.0% cpu (+ 5.8%, p=0.147 vs net-next)
TCP 1 stream, GRO off, busy_read = 50:
net-next: 6.488 Gbps
after #1: 6.625 Gbps (+ 2.1%, p=0.059 vs net-next)
after #3: 7.351 Gbps (+13.3%, p=0.026 vs net-next)
TCP_RR 100 streams, GRO off, 8000 byte payload
net-next: 995.083 us
after #1: 969.167 us (- 2.6%, p=0.204 vs net-next)
after #3: 976.433 us (- 1.9%, p=0.254 vs net-next)
TCP_RR 100 streams, GRO off, 8000 byte payload, busy_read = 50:
net-next: 2.851 ms
after #1: 2.871 ms (+ 0.7%, p=0.134 vs net-next)
after #3: 2.937 ms (+ 3.0%, p<0.001 vs net-next)
TCP_RR 100 streams, GRO off, 1 byte payload, busy_read = 50:
net-next: 867.317 us
after #1: 865.717 us (- 0.2%, p=0.334 vs net-next)
after #3: 868.517 us (+ 0.1%, p=0.414 vs net-next)
(*) These tests produced a mixture of line-rate and below-line-rate results,
meaning that statistically speaking the results were 'censored' by the
upper bound, and were thus not normally distributed, making a Welch t-test
mathematically invalid. I therefore also calculated estimators according
to [1], which gave the following:
net-next: 8.133 Gbps
after #1: 8.130 Gbps (- 0.0%, p=0.499 vs net-next)
after #3: 7.680 Gbps (- 5.6%, p=0.285 vs net-next)
(though my procedure for determining ν wasn't mathematically well-founded
either, so take that p-value with a grain of salt).
A further check came from dividing the bandwidth figure by the CPU usage for
each test run, giving:
net-next: 3.461
after #1: 3.198 (- 7.6%, p=0.145 vs net-next)
after #3: 3.641 (+ 5.2%, p=0.280 vs net-next)
The above results are fairly mixed, and in most cases not statistically
significant. But I think we can roughly conclude that the series
marginally improves non-GROable throughput, without hurting latency
(except in the large-payload busy-polling case, which in any case yields
horrid performance even on net-next (almost triple the latency without
busy-poll). Also, drivers which, unlike sfc, pass UDP traffic to GRO
would expect to see a benefit from gaining access to batching.
Changed in v3:
* gro_normal_batch sysctl now uses SYSCTL_ONE instead of &one
* removed RFC tags (no comments after a week means no-one objects, right?)
Changed in v2:
* During busy poll, call gro_normal_list() to receive batched packets
after each cycle of the napi busy loop. See comments in Patch #3 for
complications of doing the same in busy_poll_stop().
[1]: Cohen 1959, doi: 10.1080/00401706.1959.10489859
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When GRO decides not to coalesce a packet, in napi_frags_finish(), instead
of passing it to the stack immediately, place it on a list in the napi
struct. Then, at flush time (napi_complete_done(), napi_poll(), or
napi_busy_loop()), call netif_receive_skb_list_internal() on the list.
We'd like to do that in napi_gro_flush(), but it's not called if
!napi->gro_bitmask, so we have to do it in the callers instead. (There are
a handful of drivers that call napi_gro_flush() themselves, but it's not
clear why, or whether this will affect them.)
Because a full 64 packets is an inefficiently large batch, also consume the
list whenever it exceeds gro_normal_batch, a new net/core sysctl that
defaults to 8.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Same rationale as for sfc, except that this wasn't performance-tested.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already scored points when handling the RX event, no-one else does this,
and looking at the history it appears this was originally meant to only
score on merges, not on GRO_NORMAL. Moreover, it gets in the way of
changing GRO to not immediately pass GRO_NORMAL skbs to the stack.
Performance testing with four TCP streams received on a single CPU (where
throughput was line rate of 9.4Gbps in all tests) showed a 13.7% reduction
in RX CPU usage (n=6, p=0.03).
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Supported ports in ethtool <eth1> are displayed based on media type.
For media type fibre and twinaxial, port type is "FIBRE". Media type
Base-T is "TP" and media KR is "Backplane".
V1->V2:
Corrected the subject.
Signed-off-by: Rahul Verma <rahulv@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All refcount operations are protected by spinlocks now.
Then the atomic counter can be replaced by a normal int.
This patch depends on PATCH 1/2.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The atomic_dec_and_test() is not safe because it is
outside of locks.
Move the locks of t4_smte_free() to its caller,
cxgb4_smt_release() to protect the atomic decrement.
Fixes: 3bdb376e69 ("cxgb4: introduce SMT ops to prepare for SMAC rewrite support")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IPv4 and IPv6 l2tp tests. Current set is over IP and with
IPsec.
v2
- add l2tp.sh to TEST_PROGS in Makefile
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
refcount_t is better for reference counters since its
implementation can prevent overflows.
So convert atomic_t ref counters to refcount_t.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
refcount_t is better for reference counters since its
implementation can prevent overflows.
So convert atomic_t ref counters to refcount_t.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- bump version strings, by Simon Wunderlich
- Replace usage of strlcpy with strscpy, by Sven Eckelmann
- Add OGMv2 per-interface queue and aggregations, by Linus Luessing
(2 patches)
-----BEGIN PGP SIGNATURE-----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=Cbzf
-----END PGP SIGNATURE-----
Merge tag 'batadv-next-for-davem-20190808' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This feature/cleanup patchset includes the following patches:
- bump version strings, by Simon Wunderlich
- Replace usage of strlcpy with strscpy, by Sven Eckelmann
- Add OGMv2 per-interface queue and aggregations, by Linus Luessing
(2 patches)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Yeah I should have sent a pull request last week, so there is a lot
more here than usual:
1) Fix memory leak in ebtables compat code, from Wenwen Wang.
2) Several kTLS bug fixes from Jakub Kicinski (circular close on
disconnect etc.)
3) Force slave speed check on link state recovery in bonding 802.3ad
mode, from Thomas Falcon.
4) Clear RX descriptor bits before assigning buffers to them in
stmmac, from Jose Abreu.
5) Several missing of_node_put() calls, mostly wrt. for_each_*() OF
loops, from Nishka Dasgupta.
6) Double kfree_skb() in peak_usb can driver, from Stephane Grosjean.
7) Need to hold sock across skb->destructor invocation, from Cong
Wang.
8) IP header length needs to be validated in ipip tunnel xmit, from
Haishuang Yan.
9) Use after free in ip6 tunnel driver, also from Haishuang Yan.
10) Do not use MSI interrupts on r8169 chips before RTL8168d, from
Heiner Kallweit.
11) Upon bridge device init failure, we need to delete the local fdb.
From Nikolay Aleksandrov.
12) Handle erros from of_get_mac_address() properly in stmmac, from
Martin Blumenstingl.
13) Handle concurrent rename vs. dump in netfilter ipset, from Jozsef
Kadlecsik.
14) Setting NETIF_F_LLTX on mac80211 causes complete breakage with
some devices, so revert. From Johannes Berg.
15) Fix deadlock in rxrpc, from David Howells.
16) Fix Kconfig deps of enetc driver, we must have PHYLIB. From Yue
Haibing.
17) Fix mvpp2 crash on module removal, from Matteo Croce.
18) Fix race in genphy_update_link, from Heiner Kallweit.
19) bpf_xdp_adjust_head() stopped working with generic XDP when we
fixes generic XDP to support stacked devices properly, fix from
Jesper Dangaard Brouer.
20) Unbalanced RCU locking in rt6_update_exception_stamp_rt(), from
David Ahern.
21) Several memory leaks in new sja1105 driver, from Vladimir Oltean"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (214 commits)
net: dsa: sja1105: Fix memory leak on meta state machine error path
net: dsa: sja1105: Fix memory leak on meta state machine normal path
net: dsa: sja1105: Really fix panic on unregistering PTP clock
net: dsa: sja1105: Use the LOCKEDS bit for SJA1105 E/T as well
net: dsa: sja1105: Fix broken learning with vlan_filtering disabled
net: dsa: qca8k: Add of_node_put() in qca8k_setup_mdio_bus()
net: sched: sample: allow accessing psample_group with rtnl
net: sched: police: allow accessing police->params with rtnl
net: hisilicon: Fix dma_map_single failed on arm64
net: hisilicon: fix hip04-xmit never return TX_BUSY
net: hisilicon: make hip04_tx_reclaim non-reentrant
tc-testing: updated vlan action tests with batch create/delete
net sched: update vlan action for batched events operations
net: stmmac: tc: Do not return a fragment entry
net: stmmac: Fix issues when number of Queues >= 4
net: stmmac: xgmac: Fix XGMAC selftests
be2net: disable bh with spin_lock in be_process_mcc
net: cxgb3_main: Fix a resource leak in a error path in 'init_one()'
net: ethernet: sun4i-emac: Support phy-handle property for finding PHYs
net: bridge: move default pvid init/deinit to NETDEV_REGISTER/UNREGISTER
...
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2019-08-05
This series contains updates to i40e driver only.
Dmitrii adds missing statistic counters for VEB and VEB TC's.
Slawomir adds support for logging the "Disable Firmware LLDP" flag
option and its current status.
Jake fixes an issue where VF's being notified of their link status
before their queues are enabled which was causing issues. So always
report link status down when the VF queues are not enabled. Also adds
future proofing when statistics are added or removed by adding checks to
ensure the data pointer for the strings lines up with the expected
statistics count.
Czeslaw fixes the advertised mode reported in ethtool for FEC, where the
"None BaseR RS" was always being displayed no matter what the mode it
was in. Also added logging information when the PF is entering or
leaving "allmulti" (or promiscuous) mode. Fixed up the logging logic
for VF's when leaving multicast mode to not include unicast as well.
v2: drop Aleksandr's patch (previously patch #2 in the series) to
display the VF MAC address that is set by the VF while community
feedback is addressed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently in function ovs_dp_process_packet(), return values of
ovs_execute_actions() are silently discarded. This patch prints out
an debug message when error happens so as to provide helpful hints
for debugging.
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean says:
====================
Fixes for SJA1105 DSA: FDBs, Learning and PTP
This is an assortment of functional fixes for the sja1105 switch driver
targeted for the "net" tree (although they apply on net-next just as
well).
Patch 1/5 ("net: dsa: sja1105: Fix broken learning with vlan_filtering
disabled") repairs a breakage introduced in the early development stages
of the driver: support for traffic from the CPU has broken "normal"
frame forwarding (based on DMAC) - there is connectivity through the
switch only because all frames are flooded.
I debated whether this patch qualifies as a fix, since it puts the
switch into a mode it has never operated in before (aka SVL). But
"normal" forwarding did use to work before the "Traffic support for
SJA1105 DSA driver" patchset, and arguably this patch should have been
part of that.
Also, it would be strange for this feature to be broken in the 5.2 LTS.
Patch 2/5 ("net: dsa: sja1105: Use the LOCKEDS bit for SJA1105 E/T as
well") is a simplification of a previous FDB-related patch that is
currently in the 5.3 rc's.
Patches 3/5 - 5/5 fix various crashes found while running linuxptp over the
switch ports for extended periods of time, or in conjunction with other
error conditions. The fixed-up commits were all introduced in 5.2.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When RX timestamping is enabled and two link-local (non-meta) frames are
received in a row, this constitutes an error.
The tagger is always caching the last link-local frame, in an attempt to
merge it with the meta follow-up frame when that arrives. To recover
from the above error condition, the initial cached link-local frame is
dropped and the second frame in a row is cached (in expectance of the
second meta frame).
However, when dropping the initial link-local frame, its backing memory
was being leaked.
Fixes: f3097be21b ("net: dsa: sja1105: Add a state machine for RX timestamping")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After a meta frame is received, it is associated with the cached
sp->data->stampable_skb from the DSA tagger private structure.
Cached means its refcount is incremented with skb_get() in order for
dsa_switch_rcv() to not free it when the tagger .rcv returns NULL.
The mistake is that skb_unref() is not the correct function to use. It
will correctly decrement the refcount (which will go back to zero) but
the skb memory will not be freed. That is the job of kfree_skb(), which
also calls skb_unref().
But it turns out that freeing the cached stampable_skb is in fact not
necessary. It is still a perfectly valid skb, and now it is even
annotated with the partial RX timestamp. So remove the skb_copy()
altogether and simply pass the stampable_skb with a refcount of 1
(incremented by us, decremented by dsa_switch_rcv) up the stack.
Fixes: f3097be21b ("net: dsa: sja1105: Add a state machine for RX timestamping")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IS_ERR_OR_NULL(priv->clock) check inside
sja1105_ptp_clock_unregister() is preventing cancel_delayed_work_sync
from actually being run.
Additionally, sja1105_ptp_clock_unregister() does not actually get run,
when placed in sja1105_remove(). The DSA switch gets torn down, but the
sja1105 module does not get unregistered. So sja1105_ptp_clock_unregister
needs to be moved to sja1105_teardown, to be symmetrical with
sja1105_ptp_clock_register which is called from the DSA sja1105_setup.
It is strange to fix a "fixes" patch, but the probe failure can only be
seen when the attached PHY does not respond to MDIO (issue which I can't
pinpoint the reason to) and it goes away after I power-cycle the board.
This time the patch was validated on a failing board, and the kernel
panic from the fixed commit's message can no longer be seen.
Fixes: 29dd908d35 ("net: dsa: sja1105: Cancel PTP delayed work on unregister")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It looks like the FDB dump taken from first-generation switches also
contains information on whether entries are static or not. So use that
instead of searching through the driver's tables.
Fixes: d763778224 ("net: dsa: sja1105: Implement is_static for FDB entries on E/T")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When put under a bridge with vlan_filtering 0, the SJA1105 ports will
flood all traffic as if learning was broken. This is because learning
interferes with the rx_vid's configured by dsa_8021q as unique pvid's.
So learning technically still *does* work, it's just that the learnt
entries never get matched due to their unique VLAN ID.
The setting that saves the day is Shared VLAN Learning, which on this
switch family works exactly as desired: VLAN tagging still works
(untagged traffic gets the correct pvid) and FDB entries are still
populated with the correct contents including VID. Also, a frame cannot
violate the forwarding domain restrictions enforced by its classified
VLAN. It is just that the VID is ignored when looking up the FDB for
taking a forwarding decision (selecting the egress port).
This patch activates SVL, and the result is that frames with a learnt
DMAC are no longer flooded in the scenario described above.
Now exactly *because* SVL works as desired, we have to revisit some
earlier patches:
- It is no longer necessary to manipulate the VID of the 'bridge fdb
{add,del}' command when vlan_filtering is off. This is because now,
SVL is enabled for that case, so the actual VID does not matter*.
- It is still desirable to hide dsa_8021q VID's in the FDB dump
callback. But right now the dump callback should no longer hide
duplicates (one per each front panel port's pvid, plus one for the
VLAN that the CPU port is going to tag a TX frame with), because there
shouldn't be any (the switch will match a single FDB entry no matter
its VID anyway).
* Not really... It's no longer necessary to transform a 'bridge fdb add'
into 5 fdb add operations, but the user might still add a fdb entry with
any vid, and all of them would appear as duplicates in 'bridge fdb
show'. So force a 'bridge fdb add' to insert the VID of 0**, so that we
can prune the duplicates at insertion time.
** The VID of 0 is better than 1 because it is always guaranteed to be
in the ports' hardware filter. DSA also avoids putting the VID inside
the netlink response message towards the bridge driver when we return
this particular VID, which makes it suitable for FDB entries learnt
with vlan_filtering off.
Fixes: 227d07a07e ("net: dsa: sja1105: Add support for traffic through standalone ports")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Georg Waibel <georg.waibel@sensor-technik.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each iteration of for_each_available_child_of_node() puts the previous
node, but in the case of a return from the middle of the loop, there
is no put, thus causing a memory leak. Hence add an of_node_put() before
the return.
Additionally, the local variable ports in the function
qca8k_setup_mdio_bus() takes the return value of of_get_child_by_name(),
which gets a node but does not put it. If the function returns without
putting ports, it may cause a memory leak. Hence put ports before the
mid-loop return statement, and also outside the loop after its last usage
in this function.
Issues found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Josh Hunt
Jiri Pirko
Eric Dumazet
Denis Efremov
Heiner Kallweit
YueHaibing
David S. Miller
Jose Abreu
John Rutherford
wenxu
Edward Cree
Rahul Verma
Chuhong Yuan
David Ahern
Alexey Dobriyan
Linus Torvalds
Yifeng Sun
Vladimir Oltean
Nishka Dasgupta