It turns out the devices from Playback Design need the delay quirk
after usb_set_interface from clocks.c as well. Make it a proper
quirks function and factor out the code to quirks.c.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For playback add the codec-side delay to the timestamp, for capture
subtract it. This brings the timestamps in line with the time that
was recently added to the delay reporting.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Correct pin configs for the Acer AC700. Most importantly indicate
that SPDIF is connected, it routes to HDMI out.
Similar to Aspire models, chain in the DMIC fixup and allow it to be
applied to this codec (ALC269VB) as well.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The DSP in the CA0132 codec adds a variable latency to audio depending
on what processing is being done. Add a new patch op to return that
latency for capture and playback streams. The latency is determined
by which blocks are enabled and knowing how much latency is added by
each block.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a new codec PCM ops, get_delay(), to obtain the codec/stream-
specific PCM delay count. When it's NULL, nothing changes.
This new feature was requested for CA0132, which has significant
delays in the path depending on the running DSP code.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some clocks might be read-only, e.g., external clocks (see also
UAC2 4.7.2.1).
In this case, setting the sample frequency will always fail
(even if the rate is equal to the current clock rate),
therefore do not write, but read the value and compare to the
requested rate.
If the clock is read only, avoid reading it twice.
If it doesn't match, return -ENXIO since the clock is invalid for
this configuration.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Show the error code returned from the USB subsystem in
the debug messages.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a module param to disable auto clock selection.
This is provided for users that expect the audio stream to
fail when the clock source is invalid (e.g., the word clock
was unintentionally disconnected).
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If a selector is available on a device, it may be pointing to a
clock source which is currently invalid.
If there is a valid clock source which can be selected, switch
to it.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move the check that parse_audio_format_rates_v2() do after
receiving the clock source entity ID directly into the find
function and add a validation flag to the function.
This patch does not introduce any logic flow change.
It is provided to allow introducing automatic clock switching
easier later. By moving this uac_clock_source_is_valid callsite,
2 additional callsites can be avoided.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace the endianness conversions with the kernel-wide swabbing macros
in get/set_sample_rate_v2.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Correct spelling of snd_usb_endpoint_implict_feedback_sink in all
occurances.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Minor style fix, following a general code style in the kernel.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just for cleaning up, introduce a new function get_sample_rate_v2()
for replacing two identical calls in set_sample_rate_v2().
No functional change.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The C-Media CM6631 USB receiver doesn't respond to changes in sample rate
while the interface is active. The same behavior is observed in other UAC2
hardware like the VIA VT1731.
Reset the interface after setting the sampling frequency on sample rate
changes, to ensure that the sample rate set by snd_usb_init_sample_rate() is
used. Otherwise, the device will try to use the sample rate of the previous
stream, causing distorted sound on sample rate changes.
The reset is performed for all UAC2 devices, as it should not affect a
standards compliant device, but it is only necessary for C-Media CM6631,
VIA VT1731 and possibly others.
Failure to read sample rate from the device is not handled as an error in
set_sample_rate_v2(), as (permanent or intermittent) failure to read sample
rate isn't essential for a successful sample rate set.
Signed-off-by: Torstein Hegge <hegge@resisty.net>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch let ELD debug message show 'pin_eld->monitor_present' which reflects
the real pin response to verb GET_PIN_SENSE.
'eld->monitor_present' should not be used here because 'eld' is a temp
structure now and so its "monitor_present" is not set.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Acked-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In function snd_hdmi_get_eld(), the variable 'ret' should be initialized to 0.
Otherwise it will be returned uninitialized as non-zero after ELD info is got
successfully. Thus hdmi_present_sense() will always assume ELD info is invalid
by mistake, and /proc file system cannot show the proper ELD info.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Cc: stable@vger.kernel.org
Acked-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A few more fixes here and there, including quite a few nasty driver
specific ones, but nothing that has a major general impact.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=rovv
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v3.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v3.9
A few more fixes here and there, including quite a few nasty driver
specific ones, but nothing that has a major general impact.
Turing on the headphone amp interferes with the impedance measurement
used to detect a TRRS style headset microphone. Delay the HP turn on
until 500ms after the jack is detected, allowing the mic detection
state machine to run to completion.
Signed-off-by: Chih-Chung Chang <chihchung@chromium.org>
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Used kmemdup instead of replicating it's behaviour with kmalloc followed
by memcpy.
Patch found using coccinelle.
Signed-off-by: Alexandru Gheorghiu <gheorghiuandru@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Used kmemdup instead of replicating it's behaviour with kmalloc followed
by memcpy.
Patch found using coccinelle.
Signed-off-by: Alexandru Gheorghiu <gheorghiuandru@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pull SCSI target fixes from Nicholas Bellinger:
"These are mostly minor fixes this time around. The iscsi-target CHAP
big-endian bugfix and bump FD_MAX_SECTORS=2048 default patch to allow
1MB sized I/Os for FILEIO backends on >= v3.5 code are both CC'ed to
stable.
Also, there is a persistent reservations regression that has recently
been reported for >= v3.8.x code, that is currently being tracked down
for v3.9."
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target/pscsi: Reject cross page boundary case in pscsi_map_sg
target/file: Bump FD_MAX_SECTORS to 2048 to handle 1M sized I/Os
tcm_vhost: Flush vhost_work in vhost_scsi_flush()
tcm_vhost: Add missed lock in vhost_scsi_clear_endpoint()
target: fix possible memory leak in core_tpg_register()
target/iscsi: Fix mutual CHAP auth on big-endian arches
target_core_sbc: use noop for SYNCHRONIZE_CACHE
- recent regressions in raid5
- recent regressions in dmraid
- a few instances of CONFIG_MULTICORE_RAID456 linger
Several tagged for -stable
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=Rycs
-----END PGP SIGNATURE-----
Merge tag 'md-3.9-fixes' of git://neil.brown.name/md
Pull md fixes from NeilBrown:
"A few bugfixes for md
- recent regressions in raid5
- recent regressions in dmraid
- a few instances of CONFIG_MULTICORE_RAID456 linger
Several tagged for -stable"
* tag 'md-3.9-fixes' of git://neil.brown.name/md:
md: remove CONFIG_MULTICORE_RAID456 entirely
md/raid5: ensure sync and DISCARD don't happen at the same time.
MD: Prevent sysfs operations on uninitialized kobjects
MD RAID5: Avoid accessing gendisk or queue structs when not available
md/raid5: schedule_construction should abort if nothing to do.
Pull i2c fixes from Wolfram Sang:
"One bugfix for the tegra driver. Two updates regarding email
addresses and MAINTAINERS which I like to have up-to-date so people
can be reached immediately. While we are here, there is on PCI_ID
addition."
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
MAINTAINERS: add maintainer entry for atmel i2c driver
i2c: Fix my e-mail address in drivers and documentation
i2c: iSMT: add Intel Avoton DeviceIDs
i2c: tegra: check the clk_prepare_enable() return value
Pull watchdog fixes from Wim Van Sebroeck:
"Fix a boot issues and correct the AcpiMmioSel bitmask in the
sp5100_tco watchdog device driver"
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: sp5100_tco: Set the AcpiMmioSel bitmask value to 1 instead of 2
watchdog: sp5100_tco: Remove code that may cause a boot failure
When KMS has parsed an EDID "detailed timing", it leaves the frame rate
zeroed. Consecutive (debug-) output of that mode thus yields 0 for
vsync. This simple fix also speeds up future invocations of
drm_mode_vrefresh().
While it is debatable whether this qualifies as a -stable fix I'd apply
it for consistency's sake; drm_helper_probe_single_connector_modes()
does the same thing already for all probed modes.
Cc: stable@vger.kernel.org
Signed-off-by: Torsten Duwe <duwe@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
EDID spreads some values across multiple bytes; bit-fiddling is needed
to retrieve these. The current code to parse "detailed timings" has a
cut&paste error that results in a vsync offset of at most 15 lines
instead of 63.
See
http://en.wikipedia.org/wiki/EDID
and in the "EDID Detailed Timing Descriptor" see bytes 10+11 show why
that needs to be a left shift.
Cc: stable@vger.kernel.org
Signed-off-by: Torsten Duwe <duwe@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull NVMe driver update from Matthew Wilcox:
"These patches have mostly been baking for a few months; sorry I didn't
get them in during the merge window. They're all bug fixes, except
for the addition of the SMART log and the addition to MAINTAINERS."
* git://git.infradead.org/users/willy/linux-nvme:
NVMe: Add namespaces with no LBA range feature
MAINTAINERS: Add entry for the NVMe driver
NVMe: Initialize iod nents to 0
NVMe: Define SMART log
NVMe: Add result to nvme_get_features
NVMe: Set result from user admin command
NVMe: End queued bio requests when freeing queue
NVMe: Free cmdid on nvme_submit_bio error
Merge misc fixes from Andrew Morton.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mqueue: sys_mq_open: do not call mnt_drop_write() if read-only
mm/hotplug: only free wait_table if it's allocated by vmalloc
dma-debug: update DMA debug API to better handle multiple mappings of a buffer
dma-debug: fix locking bug in check_unmap()
drivers/rtc/rtc-at91rm9200.c: use a variable for storing IMR
drivers/video/ep93xx-fb.c: include <linux/io.h> for devm_ioremap()
drivers/rtc/rtc-da9052.c: fix for rtc device registration
mm: zone_end_pfn is too small
poweroff: change orderly_poweroff() to use schedule_work()
mm/hugetlb: fix total hugetlbfs pages count when using memory overcommit accouting
printk: Provide a wake_up_klogd() off-case
irq_work.h: fix warning when CONFIG_IRQ_WORK=n
mnt_drop_write() must be called only if mnt_want_write() succeeded,
otherwise the mnt_writers counter will diverge.
mnt_writers counters are used to check if remounting FS as read-only is
OK, so after an extra mnt_drop_write() call, it would be impossible to
remount mqueue FS as read-only. Besides, on umount a warning would be
printed like this one:
=====================================
[ BUG: bad unlock balance detected! ]
3.9.0-rc3 #5 Not tainted
-------------------------------------
a.out/12486 is trying to release lock (sb_writers) at:
mnt_drop_write+0x1f/0x30
but there are no more locks to release!
Signed-off-by: Vladimir Davydov <vdavydov@parallels.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
zone->wait_table may be allocated from bootmem, it can not be freed.
Signed-off-by: Jianguo Wu <wujianguo@huawei.com>
Reviewed-by: Tang Chen <tangchen@cn.fujitsu.com>
Cc: Tang Chen <tangchen@cn.fujitsu.com>
Cc: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There were reports of the igb driver unmapping buffers without calling
dma_mapping_error. On closer inspection issues were found in the DMA
debug API and how it handled multiple mappings of the same buffer.
The issue I found is the fact that the debug_dma_mapping_error would
only set the map_err_type to MAP_ERR_CHECKED in the case that the was
only one match for device and device address. However in the case of
non-IOMMU, multiple addresses existed and as a result it was not setting
this field once a second mapping was instantiated. I have resolved this
by changing the search so that it instead will now set MAP_ERR_CHECKED
on the first buffer that matches the device and DMA address that is
currently in the state MAP_ERR_NOT_CHECKED.
A secondary side effect of this patch is that in the case of multiple
buffers using the same address only the last mapping will have a valid
map_err_type. The previous mappings will all end up with map_err_type
set to MAP_ERR_CHECKED because of the dma_mapping_error call in
debug_dma_map_page. However this behavior may be preferable as it means
you will likely only see one real error per multi-mapped buffer, versus
the current behavior of multiple false errors mer multi-mapped buffer.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Reviewed-by: Shuah Khan <shuah.khan@hp.com>
Tested-by: Shuah Khan <shuah.khan@hp.com>
Cc: Jakub Kicinski <kubakici@wp.pl>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In check_unmap() it is possible to get into a dead-locked state if
dma_mapping_error is called. The problem is that the bucket is locked in
check_unmap, and locked again by debug_dma_mapping_error which is called
by dma_mapping_error. To resolve that we must release the lock on the
bucket before making the call to dma_mapping_error.
[akpm@linux-foundation.org: restore 80-col trickery to be consistent with the rest of the file]
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Reviewed-by: Shuah Khan <shuah.khan@hp.com>
Tested-by: Shuah Khan <shuah.khan@hp.com>
Cc: Jakub Kicinski <kubakici@wp.pl>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On some revisions of AT91 SoCs, the RTC IMR register is not working.
Instead of elaborating a workaround for that specific SoC or IP version,
we simply use a software variable to store the Interrupt Mask Register
and modify it for each enabling/disabling of an interrupt. The overhead
of this is negligible anyway.
The interrupt mask register (IMR) for the RTC is broken on the AT91SAM9x5
sub-family of SoCs (good overview of the members here:
http://www.eewiki.net/display/linuxonarm/AT91SAM9x5 ). The "user visible
effect" is the RTC doesn't work.
That sub-family is less than two years old and only has devicetree (DT)
support and came online circa lk 3.7 . The dust is yet to settle on the
DT stuff at least for AT91 SoCs (translation: lots of stuff is still
broken, so much that it is hard to know where to start).
The fix in the patch is pretty simple: just shadow the silicon IMR
register with a variable in the driver. Some older SoCs (pre-DT) use the
the rtc-at91rm9200 driver (e.g. obviously the AT91RM9200) and they should
not be impacted by the change. There shouldn't be a large volume of
interrupts associated with a RTC.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Reported-by: Douglas Gilbert <dgilbert@interlog.com>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit be86781497 ("drivers/video/ep93xx-fb.c: use devm_ functions")
introduced a build error:
drivers/video/ep93xx-fb.c: In function 'ep93xxfb_probe':
drivers/video/ep93xx-fb.c:532: error: implicit declaration of function 'devm_ioremap'
drivers/video/ep93xx-fb.c:533: warning: assignment makes pointer from integer without a cast
Include <linux/io.h> to pickup the declaration of 'devm_ioremap'.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Acked-by: Ryan Mallon <rmallon@gmail.com>
Cc: Damien Cassou <damien.cassou@lifl.fr>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the virtual irq since now MFD only handles virtual irq
Without this patch rtc device will fail in registration.
(akpm: Ashish has a different version whcih will be needed for 3.8.x and
earlier kernels)
Signed-off-by: Ashish <ashish.jangam@kpitcummins.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Daniel Mack
Dylan Reid
Takashi Iwai
Eldad Zack
Torstein Hegge
Mengdong Lin
Chih-Chung Chang
Alexandru Gheorghiu
Mark Brown
Linus Torvalds
Torsten Duwe
Vladimir Davydov
Jianguo Wu
Alexander Duyck
Nicolas Ferre
H Hartley Sweeten
Ashish Jangam