Read adapter's physical port number from interrupt pin register
and use it instead of pci function number to offset into the
nvram to obtain the port's configuration parameters.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
As it may be useful during debugging to use a specific firmware
image.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Changing a lun's queue depth (/sys/block/sdX/device/queue_depth)
isn't sticky when the device is connected via a QLogic fibre
channel adapter.
The QLogic qla2xxx fibre channel driver dynamically adjusts a
lun's queue depth. If a user has a specific need to limit the
number of commands issued to a lun (say a tape drive, or a shared
raid where the total commands issued to all luns is limited at
the controller level, for example) and writes a limiting value to
/sys/block/sdXX/device/queue_depth, the qla2xxx driver will
silently and gradually increase the queue depth back to the
driver limit of ql2xmaxqdepth. While reducing this value (module
parameter) or increasing the interval between ramp ups
(ql2xqfullrampup) offers the potential for a work around it would
be better to have the option of just disabling the dynamic
adjustment of queue depth.
This patch implements an "off switch" as a module parameter.
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Set the conditional plogi option bit whenever logging in the
fabric management server (if it is already logged in, it does not
need an explicit login; an implicit login suffices).
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Information present in static table is only valid for pre-ISP25xx
adapters.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
srbs used to maintain a reference to the request queue on which
it was enqueued. This is no longer required as the request queue
pointer is now maintained in the scsi host that issues the srb.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Set the module parameter ql2xmultique_tag to 1 to enable this
feature. In this mode, the total number of response queues
created is equal to the number of online cpus. Turning the block
layer's rq_affinity mode on enables requests to be routed to the
proper cpu and at the same time it enables completion of the IO
in a response queue that is affined to the cpu in the request
path.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Set the number of request queues to the module paramater
ql2xmaxqueues. Each vport gets a request queue. The QoS value
set to the request queues determines priority control for queued
IOs. If QoS value is not specified, the vports use the default
queue 0.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Cull and export VN_Port MAC address and VLAN_ID information on
supported FCoE ISPs.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The short-circuit to skip the non-applicable 'full-login-lip'
process on 81xx ISPs was nested too deeply in the 'bus-reset'
routine, as the code in qla2x00_loop_reset() should skip the
whole enable_lip_full_login process. The original code could
cause device tear-down due to the qla2x00_wait_for_loop_ready()
call taking a large amount of time.
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The last request completion cleanup in scsi_lib left an unused
this_count variable in scsi_io_completion().
(It was used before in a code segment that now uses blk_end_request_all())
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Use new blk_make_request() to allocate a request from bio
and avoid using deprecated blk_rq_append_bio().
This patch is dependent on a block layer patch titled:
[BLOCK] New blk_make_request() takes bio returns request
This is the last usage of blk_rq_append_bio in osd, it can now
be un-exported.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
CC: Jeff Garzik <jeff@garzik.org>
CC: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Now that blk_rq_map_kern will append the buffer onto the
request we can use it easily for adding extra segments
(eg. attributes)
This patch is dependent on a block layer patch titled:
[BLOCK] allow blk_rq_map_kern to append to requests
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
In commit c3a4d78c58, while introducing
rq->resid_len, the default value of residue count was changed from
full count to zero. The conversion was done under the assumption that
when a request fails residue count wasn't defined. However, Boaz and
James pointed out that this wasn't true and the residue count should
be preserved for failed requests too.
This patchset restores the original behavior by setting rq->resid_len
to blk_rq_bytes(rq) on request start and restoring explicit clearing
in affected drivers. While at it, take advantage of the fact that
rq->resid_len is set to full count where applicable.
* ide-cd: rq->resid_len cleared on pc success
* mptsas: req->resid_len cleared on success
* sas_expander: rsp/req->resid_len cleared on success
* mpt2sas_transport: req->resid_len cleared on success
* ide-cd, ide-tape, mptsas, sas_host_smp, mpt2sas_transport, ub: take
advantage of initial full count to simplify code
Boaz Harrosh spotted bug in resid_len initialization. Fixed as
suggested.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Borislav Petkov <petkovbb@googlemail.com>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
In Commit
commit 3b8b5c9b1f
Author: Eric Moore <eric.moore@lsi.com>
Date: Tue Apr 21 15:44:27 2009 -0600
[SCSI] mpt2sas : bump driver version to 01.100.02.00
The MPT2SAS_MAJOR_VERSION didn't get bumped from 00 to 01 so
applications will see it incorrectly as 00.100.02.00 driver instead of
01.100.02.00. Fix by making MPT2SAS_MAJOR_VERSION match the major
number in MPT2SAS_DRIVER_VERSION
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
If we can find a type NETDEV_HW_ADDR_T_SAN mac address from the
corresponding netdev for a fcoe interface then sets up added the
fc->ctlr.spma flag and stores spma mode address in ctl_src_addr.
In case the spma flag is set then:-
1. Adds spma mode MAC address in ctl_src_addr as secondary
MAC address, the FLOGI for FIP and pre-FIP will go out
using this address.
2. Cleans up stored spma MAC address in ctl_src_addr in
fcoe_netdev_cleanup.
3. Sets up spma bit in fip_flags for FIP solicitations along
with exiting FPMA bit setting.
4. Initialize the FLOGI FIP MAC descriptor to stored spma
MAC address in ctl_src_addr. This is used as proposed
FCoE MAC address from initiator along with both SPMA
and FPMA bit set in FIP solicitation, in response the
switch may grant any FPMA or SPMA mode MAC address to
initiator.
Removes FIP descriptor type checking against ELS type
ELS_FLOGI in fcoe_ctlr_encaps to update a FIP MAC descriptor,
instead now checks against FIP_DT_FLOGI.
I've tested this with available FPMA-only FCoE switch but
since data_src_addr is updated using same old code for
both FPMA and SPMA modes with FIP or pre-FIP links, so added
SPMA mode will work with SPMA-only switch also provided that
switch grants a valid MAC address.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently fcoe_netdev_config adds netdev pkt handler for fcoe pkts,
fcoe_if_create adds netdev pkt handler for fip packets, a secondary
MAC address is added by fcoe_netdev_config and then later cleanup
for these netdev related config/adds is done only during
fcoe_if_destroy and no cleanup done on error during fcoe interface
creation after above netdev config calling in fcoe_if_create.
So this patch adds single func for above mentioned cleanup the
fcoe_netdev_cleanup and then calls this func on either fcoe interface
destroy or exiting from fcoe_if_create due to an error after fcoe/fip
related above netdev config is done.
Moved netdev pkt handler addition code blocks for fip pkts close to
similar code block for foce pkt in fcoe_netdev_config, so that added
fcoe_netdev_cleanup could be called on error from fcoe_netdev_config
to undo these both additions for fcoe/fip pkt handlers. This move
required reference to fcoe_fip_recv in fcoe_netdev_config, so moved
fip related functions fcoe_fip_recv, fcoe_fip_send and
fcoe_update_src_mac above fcoe_netdev_config.
This consolidation will enable spma mode support in next patch to
easily add or delete spma mode mac address beside fixing current
no cleanup issue during error.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the following regression that occurred during the
scsi_dma_map()/unmap()
changes when compiling with CONFIG_DMA_API_DEBUG=y :
WARNING: at lib/dma-debug.c:496 check_unmap+0x142/0x542()
Hardware name:
3w-xxxx 0000:02:02.0: DMA-API: device driver tries to free DMA memory
it has not allocated [device address=0x0000000000000000] [size=36
bytes]
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch fixes the following regression the occurred during the
scsi_dma_map()/unmap() changes:
3w-9xxx 0001:45:00.0: DMA-API: device driver tries to free DMA memory
it has not allocated [device address=0x0000000000000000] [size=36
bytes]
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Andrew Vasquez wrote:
> fc-transport: Close state transition-window during rport deletion.
>
> After an rport's state has transitioned to FC_PORTSTATE_BLOCKED,
> but, prior to making the upcall to 'block' the scsi-target
> associated with an rport, queued commands can recycle and
> ultimately run out of retries causing failures to propagate to
> upper-level drivers. Close this transition-window by returning
> the non-'retries' modifying DID_IMM_RETRY status for submitted
> I/Os.
The same can happen for iscsi when transitioning from logged in
to failed and blocking the sdevs.
This patch converts iscsi and fc's transitions back to use DID_IMM_RETRY
instead of DID_TRANSPORT_DISRUPTED which has a limited number of retries
that we do not want to use for handling this race.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
[Addition of iscsi and fc port online devloss case conversion by Mike Christie]
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch initializes the max_target_blocked field of a scsi target
structure so that a queuecommand return value of
SCSI_MLQUEUE_TARGET_BUSY will actually result in having the
scsi_queue_insert blocking the device queue before requeuing the
command and running the queue. Otherwise, can and does cause livelock
on single CPU configurations if/when open-iSCSI software initiator's
command PDU window fills.
Signed-off-by: Ed Goggin <egoggin@vmware.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
fnic is a driver for the Cisco PCI-Express FCoE HBA
Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Commit c3a4d78c58 introduced
rq->data_len and converted residual count users to it. While
converting, it mistakenly converted scsi_end_request() to finish
requests with residual count when it wants to do is fully complete the
request. Fix it by using blk_end_request_all() instead.
This bug was spotted by Boaz Harrosh.
Signed-off-by: Tejun Heo <tj@kernel.org>
Spotted-by: Boaz Harrosh <bharrosh@panasas.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Till now block layer allowed two separate modes of request execution.
A request is always acquired from the request queue via
elv_next_request(). After that, drivers are free to either dequeue it
or process it without dequeueing. Dequeue allows elv_next_request()
to return the next request so that multiple requests can be in flight.
Executing requests without dequeueing has its merits mostly in
allowing drivers for simpler devices which can't do sg to deal with
segments only without considering request boundary. However, the
benefit this brings is dubious and declining while the cost of the API
ambiguity is increasing. Segment based drivers are usually for very
old or limited devices and as converting to dequeueing model isn't
difficult, it doesn't justify the API overhead it puts on block layer
and its more modern users.
Previous patches converted all block low level drivers to dequeueing
model. This patch completes the API transition by...
* renaming elv_next_request() to blk_peek_request()
* renaming blkdev_dequeue_request() to blk_start_request()
* adding blk_fetch_request() which is combination of peek and start
* disallowing completion of queued (not started) requests
* applying new API to all LLDs
Renamings are for consistency and to break out of tree code so that
it's apparent that out of tree drivers need updating.
[ Impact: block request issue API cleanup, no functional change ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Mike Miller <mike.miller@hp.com>
Cc: unsik Kim <donari75@gmail.com>
Cc: Paul Clements <paul.clements@steeleye.com>
Cc: Tim Waugh <tim@cyberelk.net>
Cc: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Laurent Vivier <Laurent@lvivier.info>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: Pierre Ossman <drzeus@drzeus.cx>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Stefan Weinhuber <wein@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
With the previous changes, the followings are now guaranteed for all
requests in any valid state.
* blk_rq_sectors() == blk_rq_bytes() >> 9
* blk_rq_cur_sectors() == blk_rq_cur_bytes() >> 9
Clean up accessor usages. Notable changes are
* nbd,i2o_block: end_all used instead of explicit byte count
* scsi_lib: unnecessary conditional on request type removed
[ Impact: cleanup ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Paul Clements <paul.clements@steeleye.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
With recent unification of fields, it's now guaranteed that
rq->data_len always equals blk_rq_bytes(). Convert all non-IDE direct
users to accessors. IDE will be converted in a separate patch.
Boaz: spotted incorrect data_len/resid_len conversion in osd.
[ Impact: convert direct rq->data_len usages to blk_rq_bytes() ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Darrick J. Wong <djwong@us.ibm.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
With recent cleanups, there is no place where low level driver
directly manipulates request fields. This means that the 'hard'
request fields always equal the !hard fields. Convert all
rq->sectors, nr_sectors and current_nr_sectors references to
accessors.
While at it, drop superflous blk_rq_pos() < 0 test in swim.c.
[ Impact: use pos and nr_sectors accessors ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Tested-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Acked-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Acked-by: Mike Miller <mike.miller@hp.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Paul Clements <paul.clements@steeleye.com>
Cc: Tim Waugh <tim@cyberelk.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Dario Ballabio <ballabio_dario@emc.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: unsik Kim <donari75@gmail.com>
Cc: Laurent Vivier <Laurent@lvivier.info>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Implement accessors - blk_rq_pos(), blk_rq_sectors() and
blk_rq_cur_sectors() which return rq->hard_sector, rq->hard_nr_sectors
and rq->hard_cur_sectors respectively and convert direct references of
the said fields to the accessors.
This is in preparation of request data length handling cleanup.
Geert : suggested adding const to struct request * parameter to accessors
Sergei : spotted error in patch description
[ Impact: cleanup ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Tested-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Ackec-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
rq->data_len served two purposes - the length of data buffer on issue
and the residual count on completion. This duality creates some
headaches.
First of all, block layer and low level drivers can't really determine
what rq->data_len contains while a request is executing. It could be
the total request length or it coulde be anything else one of the
lower layers is using to keep track of residual count. This
complicates things because blk_rq_bytes() and thus
[__]blk_end_request_all() relies on rq->data_len for PC commands.
Drivers which want to report residual count should first cache the
total request length, update rq->data_len and then complete the
request with the cached data length.
Secondly, it makes requests default to reporting full residual count,
ie. reporting that no data transfer occurred. The residual count is
an exception not the norm; however, the driver should clear
rq->data_len to zero to signify the normal cases while leaving it
alone means no data transfer occurred at all. This reverse default
behavior complicates code unnecessarily and renders block PC on some
drivers (ide-tape/floppy) unuseable.
This patch adds rq->resid_len which is used only for residual count.
While at it, remove now unnecessasry blk_rq_bytes() caching in
ide_pc_intr() as rq->data_len is not changed anymore.
Boaz : spotted missing conversion in osd
Sergei : spotted too early conversion to blk_rq_bytes() in ide-tape
[ Impact: cleanup residual count handling, report 0 resid by default ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Mike Miller <mike.miller@hp.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Doug Gilbert <dgilbert@interlog.com>
Cc: Mike Miller <mike.miller@hp.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Darrick J. Wong <djwong@us.ibm.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Merge reason: tracing/core was on a .30-rc1 base and was missing out on
on a handful of tracing fixes present in .30-rc5-almost.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Now that all block request data transfer is done via bio, rq->data
isn't used. Kill it.
While at it, make the roles of rq->special and buffer clear.
[ Impact: drop now unncessary field from struct request ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Boaz Harrosh <bharrosh@panasas.com>
There are many [__]blk_end_request() call sites which call it with
full request length and expect full completion. Many of them ensure
that the request actually completes by doing BUG_ON() the return
value, which is awkward and error-prone.
This patch adds [__]blk_end_request_all() which takes @rq and @error
and fully completes the request. BUG_ON() is added to to ensure that
this actually happens.
Most conversions are simple but there are a few noteworthy ones.
* cdrom/viocd: viocd_end_request() replaced with direct calls to
__blk_end_request_all().
* s390/block/dasd: dasd_end_request() replaced with direct calls to
__blk_end_request_all().
* s390/char/tape_block: tapeblock_end_request() replaced with direct
calls to blk_end_request_all().
[ Impact: cleanup ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Mike Miller <mike.miller@hp.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
OSC's OSD2 target: [git clone git://git.open-osd.org/osc-osd/ master]
(Initiator code prior to this patch must use: "git checkout CDB_VER_OSD2r01"
in the target tree above)
This is a summery of the wire changes:
* OSDv2_ADDITIONAL_CDB_LENGTH == 192 => 228 (Total CDB is now 236 bytes)
* Attributes List Element Header grew, so attribute values are 8 bytes
aligned.
* Cryptographic keys and signatures are 20 => 32
* Few new definitions.
(Still missing new standard definitions attribute values, these do not change
wire format and will be added later when needed)
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
In OSD2r04 draft, cryptographic key size changed to 32 bytes from
OSD1's 20 bytes. This causes a couple of on-the-wire structures
to change, including the CDB.
In this patch the OSD1/OSD2 handling is separated out in regard
to affected structures, but on-the-wire is still the same. All
on the wire changes will be submitted in one patch for bisect-ability.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
In OSD2r05 draft each attribute list element header was changed
so attribute-value would be 8 bytes aligned. In OSD2r01-r04
it was aligned on 2 bytes. (This is because in OSD2r01 the complete
element was 8 bytes padded at end but the header was not adjusted
and caused permanent miss-alignment.)
OSD1 elements are not padded and might be or might not be aligned.
OSD1 is still supported.
In this code we do all the code re-factoring to separate OSD1/OSD2
differences but do not change actual wire format. All wire format
changes will happen in one patch later, for bisect-ability.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
bio_map_kern() returns an ERR_PTR() not NULL.
Found by smatch (http://repo.or.cz/w/smatch.git). Compile tested.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Here's a fix for hotplug events. The useage of queue_delayed_work seems
to broke the fifo for processing of firmware events. After several iterations
of adding and removing cabling connected to jbods, the devices are not
getting added becuase kernel thread is activited out of order.
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Diagnostic buffer support is already there in the driver. This support allows
applications to pull ring buffers from controller firmware for debugging
firmware related issues.
What this patch does is sends reqeust to firmware to release the buffers prior
to host reset. This will allow what ever debug info is there prior to reset
to be dma'd to host memory. With out this fix, some of the debug data would
been lost.
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Bug fix in the broadcast primative async event code where the driver would
stop sending tm queries after the first queury was completed. This was due
driver not reseting the tm_cmds.status field back to MPT2_CMD_NOT_USED after
completing a task management request.
An addtional fix adding sanity check to insure sas_device->starget set to NULL.
During multipath testing fail over/fail back, the mid layer was holding onto
sdev longer than the fail back period, thus starget was getting set to NULL
for device being added.
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The Dell branding along with the VID, DID, SSVID, SSDID following the LSI
branding that contains the card firmware/chip/bios versions. If the SSDID
is not known but it is a Dell HBA, the driver will print the SSDID instead
of the Dell branding string. Nothing will be printed for non Dell HBAs
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The driver name needs to be at the beginining of the driver_version string in
MPT2IOCINFO ioctl. This is the same behaviour is there already in the mptsas
driver.
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The driver is not freeing message frame when returning failure from
_ctl_do_task_abort. If you call this function 500 times when its unable
to find an active task mid, you end up with no message frames.
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
There is a bug in firmware where the reply message frame says there is a
16kb sense buffer, when in reality its only 20 bytes. This fix insures
the memcpy action doesn't corrupte the memory beyond the 90 bytes allocated in
the scsi command for sense buffer.
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The poison sanity check on the reply_post_free register needs to be by 32bit,
not 64bit. The poison check is there because its possible that the driver read
the 1st 32bit before the 2nd 32bit has been written to by firmware. In other
words, this handles race between driver reading the 64 bit register, and it
being dma'd across pci memory from controller firmware as two 32bit pci writes.
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The current magic number is shared with mptsas driver. This to be unique to
fix issues with register_ioctls32_conversion in older kernels. We are making
this change across all versions of the sas2.0 drivers.
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Shifting an unsigned char implicitly casts it to a signed int. This
caused 'lba' to sign-extend and Linux would then try READ CAPACITY 16
which was not supported by at least one drive. Using the
get_unaligned_be*() helpers keeps us from having to worry about how the
extension might occur.
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The ata_sas_slave_configure was changed such that it now allocates
some memory for a drain buffer for ATAPI devices. Fixup the ipr
driver such that we no longer make this call with interrupts disabled.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The FCoE forwarder (FCF) would be selected, but then would soon time
out after three advertisements were missed. This would be 24 seconds
by default, or 3 times the keep-alive interval configured on the switch.
The cause was that the multicast address for all FIP E-nodes
was never added.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When building with a .config generated from 'make allmodconfig'
some build warnings are generated. This patch corrects the warnings,
adds a FC_FID_NONE (= 0) enumeration for FC-IDs and cleans up one
variable naming to meet our variable naming conventions. For example,
fc_lport's should be named "lport," not "lp."
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
These probably never should have been exported.
If they were needed outside of the fcoe module, they
would have been moved to libfcoe.
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
sk_buff pointers should use kfree_skb() instead of vanilla kfree().
Found by smatch (http://repo.or.cz/w/smatch.git).
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When a delete event is queued for an rport, set state to NONE so that no
other processing is done on the rport as it is being removed.
Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
After lport_destroy, the local port should not be used again. Transition
to state NONE, any incoming frames or link up should not transition out
of this state since we are deleting exchange table and cleaning up the
local port. Also, mark link as down.
Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We want to generate the rport queue event (from the logoff)
before flushing the queue otherwise the event may still be
in the queue when we logoff.
Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Rogue ports are currently not tracked on any list. The only reference
to them is through any outstanding exchanges pending on the rogue ports.
If the module is removed while a retry is set on a rogue port
(say a Plogi retry for instance), this retry is not cancelled because there
is no reference to the rogue port in the discovery rports list. Thus the
local port can clean itself up, delete the exchange pool, and then the
rogue port timeout can fire and try to start up another exchange.
This patch tracks the rogue ports in a new list disc->rogue_rports. Creating
a new list instead of using the disc->rports list keeps remote port code
change to a minimum.
1) Whenever a rogue port is created, it is immediately added to the
disc->rogue_rports list.
2) When the rogues port goes to ready, it is removed from the rogue list
and the real remote port is added to the disc->rports list
3) The removal of the rogue from the disc->rogue_rports list is done in
the context of the fc_rport_work() workQ thread in discovery callback.
4) Real rports are removed from the disc->rports list like before. Lookup
is done only in the real rports list. This avoids making large changes
to the remote port code.
5) In fc_disc_stop_rports, the rogues list is traversed in addition to the
real list to stop the rogue ports and issue logoffs on them. This way, rogue
ports get cleaned up when the local port goes away.
6) rogue remote ports are not removed from the list right away, but
removed late in fc_rport_work() context, multiple threads can find the same
remote port in the list and call rport_logoff(). Rport_logoff() only
continues with the logoff if port is not in NONE state, thus preventing
multiple logoffs and multiple list deletions.
7) Since the rport is removed from the disc list at a later stage
(in the disc callback), incoming frames can find the rport even if
rport_logoff() has been called on the rport. When rport_logoff() is called,
the rport state is set to NONE, and we are trying to cancel all exchanges
and retries on that port. While in this state, if an incoming
Plogi/Prli/Logo or other frames match the rport, we should not reply
because the rport is in the NONE state. Just drop the frame, since the
rport will be deleted soon in the disc callback (fc_rport_work)
8) In fc_disc_single(), remove rport lookup and call to fc_disc_del_target.
fc_disc_single() is called from recv_rscn_req() where rport lookup
and rport_logoff is already done.
Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
For instance, if there is a Plogi pending (remote port is in Plogi state),
and the state changes to say NONE (because the port is being logged off),
then when the Plogi resp times out, do not start a retry.
This patch partially reverts an earlier patch (libfc: check for err when
recv and state is incorrect), by moving the state check back to before
checking for error. However, if the state does not match, then there is
an additional check to see if its an error ptr or a real frame before
jumping to err or out respectively.
Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
gpn_ft_resp processing currently does not hold the discovery lock.
disc_done() thus gets called from gpn_ft_resp or from gpn_ft_parse
without the lock held. This then sets disc->pending to zero or calls
gpn_ft_req() without disc_lock held.
- Hold disc mutex during gpn_ft resp processing
- In disc_done, release the disc mutex while calling lport callback
Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
(version 2)
Fixed a bug in calculating ddp map range when search for free entries:
it was going beyond the end by one, thus corrupting gl_skb[0].
Signed-off-by: Karen Xie <kxie@chelsio.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When doing a lot (128) of large writes (256K) we can hit the cxgb3_snd_win
check pretty easily. The driver's xmit thread then takes 100% of the cpu.
The driver should not be returning -EAGAIN for this problem. It should
be returing -ENOBUFS, then when the window is opened again it should
queue the xmit thread (it already wakes the xmit thread).
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
cxgb3i was setting can_queue to only 128 commands, and was
setting the can_queue and cmd_per_lun to the same value.
This sets the can_queue to 1024 commands, and sets the cmd_per_lun
to a safer default of 32.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Set target can queue limit to the number of preallocated
session tasks we have.
This along with the cxgb3i can_queue patch will fix a throughput
problem where it could only queue one LU worth of data at a time.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
If a command's scsi cmd pdu setup fails then we can just fail
the IO to the scsi layer. If a DATA_OUT for a R2T fails then
we will want to drop the session, because it means we got a
bad request from the target (iscsi protocol error).
This patch has us propogate the error upwards so libiscsi_tcp
or libiscsi can decide what the best action is to take. It
also fixes a bug where we could try to grab the session lock
while holding it, because if iscsi_tcp drops the session in the
pdu setup callout the session lock is held when setting up the
scsi cmd pdu.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We cannot call blk_plug_device from scsi_target_queue_ready
because the q lock is not held. And we do not need to call
it from there because when we return 0, the scsi_request_fn
not_ready handling will plug the queue for us if needed.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Update driver version to 8.3.1
Also update copyright end year for driver.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
8.3.1 Fixes/Changes :
- Fix incorrect byte-swapping on word 4 of IOCB (data length) which
caused LUNs to not be discovered on big-endian (e.g. PPC)
- Remove a bad cast of MBslimaddr which loses the __iomem (sparse)
- Make lpfc_debugfs_mask_disc_trc static (sparse)
- Correct misspelled word BlockGuard in lpfc_logmsg.h comment
- Replaced repeated code segment for canceling IOCBs from a list with
a function call, lpfc_sli_cancel_iocbs().
- Increased HBQ buffers to support 40KB SSC sequences.
- Added sysfs interface to update speed and topology parameter without
link bounce.
- Fixed bug with sysfs fc_host WWNs not being updated after changing
the WWNs.
- Check if the active mailbox is NULL in the beginning of the mailbox
timeout handler - fixes panic in the mailbox timeout handler while
running IO stress test
- Fixed system panic in lpfc_pci_remove_one() due to ndlp indirect
reference to phba through vport
- Removed de-reference of scsi device after call to scsi_done() to fix
panic in scsi completion path while accessing scsi device after
scsi_done is called.
- Fixed "Nodelist not empty" message when unloading the driver after
target reboot test
- Added LP2105 HBA model description
- Added code to print all 16 words of unrecognized ASYNC events
- Fixed memory leak in vport create + delete loop
- Added support for handling dual error bit from HBA
- Fixed a driver NULL pointer dereference in lpfc_sli_process_sol_iocb
- Fixed a discovery bug with FC switch reboot in lpfc_setup_disc_node
- Take NULL termintator into account when calculating available buffer space
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
blk_rq_unmap_user() returns EFAULT if a program passes an invalid
address to kernel (the kernel fails to copy data to user space). sg
needs to pass the returned value to user space instead of ignoring
it. Before the block layer conversion, sg returns EFAULT
properly. This restores the old behavior.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
So, what's happening here is that the drive is reporting a sense of
2/4/1 ("logical unit is becoming ready") from sr_test_unit_ready(), and
then we ask for the media event notification before checking that result
at all. The check_media_event_descriptor() call isn't getting a check
condition, but it's also reporting that the tray is closed and that
there's no media. In actuality it doesn't yet know if there's media or
not, but there's no way to express that in the media event status field.
My current thought is that if it told us the device isn't yet ready, we
should return that immediately, since there's nothing that'll tell us
any more data than that reliably:
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
commit 7a192ec334 ("platform driver: fix
incorrect use of 'platform_bus_type' with 'struct device_driver') turned a
driver_UNregister into platform_driver_REGISTER. Correct this to
platform_driver_UNregister.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
There is currently only one way for userspace to say "wait for my storage
device to get ready for the modules I just loaded": to load the
scsi_wait_scan module. Expectations of userspace are that once this
module is loaded, all the (storage) devices for which the drivers
were loaded before the module load are present.
Now, there are some issues with the implementation, and the async
stuff got caught in the middle of this: The existing code only
waits for the scsy async probing to finish, but it did not take
into account at all that probing might not have begun yet.
(Russell ran into this problem on his computer and the fix works for him)
This patch fixes this more thoroughly than the previous "fix", which
had some bad side effects (namely, for kernel code that wanted to wait for
the scsi scan it would also do an async sync, which would deadlock if you did
it from async context already.. there's a report about that on lkml):
The patch makes the module first wait for all device driver probes, and then it
will wait for the scsi parallel scan to finish.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Though one can specify '-d /dev/sda1' when using blktrace, it still
traces the whole sda.
To support per-partition tracing, when we start tracing, we initialize
bt->start_lba and bt->end_lba to the start and end sector of that
partition.
Note some actions are per device, thus we don't filter 0-sector events.
The original patch and discussion can be found here:
http://marc.info/?l=linux-btrace&m=122949374214540&w=2
Signed-off-by: Shawn Du <duyuyang@gmail.com>
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
LKML-Reference: <49E42620.4050701@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix lpfc_parse_bg_err()'s use of do_div(). It should be passing a 64-bit
variable as the first parameter. However, since it's only using a 32-bit
variable, it doesn't need to use do_div() at all, but can instead use the
division operator.
This deals with the following warnings:
CC drivers/scsi/lpfc/lpfc_scsi.o
drivers/scsi/lpfc/lpfc_scsi.c: In function 'lpfc_parse_bg_err':
drivers/scsi/lpfc/lpfc_scsi.c:1397: warning: comparison of distinct pointer types lacks a cast
drivers/scsi/lpfc/lpfc_scsi.c:1397: warning: right shift count >= width of type
drivers/scsi/lpfc/lpfc_scsi.c:1397: warning: passing argument 1 of '__div64_32' from incompatible pointer type
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the second go through of the old DMA_nBIT_MASK macro,and there're not
so many of them left,so I put them into one patch.I hope this is the last round.
After this the definition of the old DMA_nBIT_MASK macro could be removed.
Signed-off-by: Yang Hongyang <yanghy@cn.fujitsu.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Tony Lindgren <tony@atomide.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Greg KH <greg@kroah.com>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is a race between resume from hibernation and the asynchronous
scanning of SCSI devices and to prevent it from happening we need to
call scsi_complete_async_scans() during resume from hibernation.
In addition, if the resume from hibernation is userland-driven, it's
better to wait for all device probes in the kernel to complete before
attempting to open the resume device.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We were calculating the wrong address for the start of the data.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Tested-by: Jeremy Higdon <jeremy@sgi.com>
Replace all DMA_31BIT_MASK macro with DMA_BIT_MASK(31)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_39BIT_MASK macro with DMA_BIT_MASK(39)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_40BIT_MASK macro with DMA_BIT_MASK(40)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (28 commits)
trivial: Update my email address
trivial: NULL noise: drivers/mtd/tests/mtd_*test.c
trivial: NULL noise: drivers/media/dvb/frontends/drx397xD_fw.h
trivial: Fix misspelling of "Celsius".
trivial: remove unused variable 'path' in alloc_file()
trivial: fix a pdlfush -> pdflush typo in comment
trivial: jbd header comment typo fix for JBD_PARANOID_IOFAIL
trivial: wusb: Storage class should be before const qualifier
trivial: drivers/char/bsr.c: Storage class should be before const qualifier
trivial: h8300: Storage class should be before const qualifier
trivial: fix where cgroup documentation is not correctly referred to
trivial: Give the right path in Documentation example
trivial: MTD: remove EOL from MODULE_DESCRIPTION
trivial: Fix typo in bio_split()'s documentation
trivial: PWM: fix of #endif comment
trivial: fix typos/grammar errors in Kconfig texts
trivial: Fix misspelling of firmware
trivial: cgroups: documentation typo and spelling corrections
trivial: Update contact info for Jochen Hein
trivial: fix typo "resgister" -> "register"
...
sg_rq_end_io() is called via rq->end_io. In some rare cases,
sg_rq_end_io calls blk_put_request/blk_rq_unmap_user (when a program
issuing a command has gone before the command completion; e.g. by
interrupting a program issuing a command before the command
completes).
We can't call blk_put_request/blk_rq_unmap_user in interrupt so the
commit c96952ed70 uses
execute_in_process_context().
The problem is that scsi_error_handler() calls rq->end_io too. We
can't call blk_put_request/blk_rq_unmap_user too in this path (we hold
q->queue_lock).
To avoid the above problem, in these rare cases, this patch always
uses schedule_work() instead of execute_in_process_context().
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
a2091_{detect,release}() can become static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
a3000_{detect,release}() can become static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
- needs to use copy_from_user for iovec before passing it to
blk_rq_map_user_iov().
- before the block layer conversion, if ->dxfer_len and sum of iovec
disagrees, the shorter one wins. However, currently sg returns
-EINVAL. This restores the old behavior.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Firmware blob is little endian
Thanks to Stephen Rothwell for fixing typos
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Firmware blob is little endian looks like this...
unsigned char Version1
unsigned char Version2
unsigned char Version3
unsigned char Padding
unsigned short start_address
unsigned short data
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Le lundi 30 mars 2009, Chris Wright a écrit :
> q->queue could be ERR_PTR(-ENOMEM) which will break unwinding
> on error. Make iscsi_pool_free more defensive.
>
Making the freeing of q->queue dependent on q->pool being set looks
really weird (although it is correct at the moment. But this seems
to be fixable in a much simpler way.
With the benefit that only the error case is slowed down. In both
cases we have a problem if q->queue contains an error value but it's
not -ENOMEM. Apparently this can't happen today, but it doesn't feel
right to assume this will always be true. Maybe it's the right time
to fix this as well.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
cxgb3i_ddp_cleanup just calls ddp_release directly so there is
no reason for the wrapper. This patch just renames ddp_release
to cxgb3i_ddp_cleanup and removes the old wrapper function.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
- Merge cxgb3i_ddp.ko to cxgb3i.ko as there is no other users.
- Bump the driver version up to 1.0.2.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Keep track of offloaded tcp connections per adapter. Close all of the
connections upon reset.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Orignally from Karen Xie, but merge conflicts/errors fixed up by
Mike Christie.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Re-initialize the ddp settings after chip reset. It includes re-initialize
the related registers and the ddp map.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Add error notification handling function which is called during chip reset.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
changes:
- set aac_cache=2 as default value to avoid performance problem
(Novell bugzilla #469922)
- Dell/PERC controller boot problem fixed (RedHat bugzilla #457552)
- WWN flag added to fix SLES10 SP1/SP2 drive detection problems
- 64-bit support changes
- DECLARE_PCI_DEVICE_TABLE macro added
- controller type changes
Signed-off-by: Achim Leubner <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Mention ATAPI. We could insert an essay about libata and ide-scsi etc but
the failure case is someone enables it which is just fine so keep it
simple.
(Revised text from suggestion by Matthew Wilcox)
Closes#7736
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This adds the support of a new SAS 6G controller (st_yel)
Signed-off-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Use config struct (st_card_info) for parameters of different controllers
Signed-off-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This adds the MSI support (default 0=off)
Signed-off-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
These are some small code fixes and changes, including:
- use 64 bit when possible
- remove some unnecessary code (in interrupt, queuecommand routine etc.)
- code change for reset handler
Signed-off-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
FIP is the new standard way to discover Fibre-Channel Forwarders (FCFs)
by sending solicitations and listening for advertisements from FCFs.
It also provides for keep-alives and period advertisements so that both
parties know they have connectivity. If the FCF loses connectivity to
the storage fabric, it can send a Link Reset to inform the E_node.
This version is also compatible with pre-FIP implementations, so no
configured selection between FIP mode and non-FIP mode is required.
We wait a couple seconds after sending the initial solicitation
and then send an old-style FLOGI. If we receive any FIP frames,
we use FIP only mode. If the old FLOGI receives a response,
we disable FIP mode. After every reset or link up, this
determination is repeated.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The foce_softc mem was reserved by libfc_host_alloc as well as
by fcoe_host_alloc.
Removes one liner fcoe_host_alloc completely, instead directly calls
libfc_host_alloc to alloc scsi_host with libfc for just one fcoe_softc
as fcoe private data.
Moves libfc_host_alloc to libfc.h since it is a libfc API, placed
lport_priv API adjacent to libfc_host_alloc since this is related
to scsi_host priv data.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Removes no where used several inline functions prefixed with skb_*
and be16_to_cpu.
Moves fcoe module specific func prototypes to fcoe.c from libfcoe.h,
moved only need for build.
Adds fcoe module header file fcoe.h and then moves fcoe module
specific fcoe_percpu_s and fcoe_softc to fcoe.h from libfcoe.h.
Moves all defines from fcoe.c to fcoe.h since now fcoe module
has its own header file fcoe.h.
[jejb: removed EXPORT_SYMBOL_GPL(fcoe_fc_crc) which caused a section mismatch]
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Moves these functions as-is from fcoe.c to libfcoe.c, since
they're are common routines:
- fcoe_wwn_from_mac
- fcoe_libfc_config
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Just sets up build environment for libfcoe module towards a
libfcoe library for libfc LLDs using FCoE as libfc transport.
Common library code to libfcoe is added in next patch.
Also, updated MODULE_LICENSE from "GPL" string to "GPL v2" for
libfc, libfcoe and fcoe modules to accurately match the licenses.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Renames libfcoe.c to fcoe.c, fcoe.c becomes the only
.c file for fcoe.ko.
Also deleted "$Id: Makefile" from fcoe module Makefle.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Moves only required code from fcoe_sw.c to libfcoe.c towards having
just one source file for fcoe module, this gets rid off default sw
transport code in a separate fcoe_sw.c file.
Very minor renaming along this move, dropped _sw_ or _SW_ use
in names and replaced them by _if_ as a auxiliary interface
functions. Now some of these funcs can be removed or merged with
other func after fcoe transport is gone, but that should be
in another patch to keep this patch simple.
Now the libfcoe.c file name for fcoe module doesn't go along well,
so the libfcoe.c file renaming to fcoe.c as the only single fcoe
module file is done in next patch to keep this patch clean
and small for review.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The fcoe transport code was added for generic FCoE transport
infrastructure to allow additional offload related module loading
on demand, this is not required anymore after recently added
different offload approach by having offload related func ops
in netdev.
This patch removes fcoe transport related code use, calls functions
directly between existing libfcoe.c and fcoe_sw.c for now, for
example fcoe_sw_destroy and fcoe_sw_create calling.
The fcoe_sw.c and libfcoe.c code will be further consolidated in
later patches and then also the default fcoe sw transport code
file fcoe_sw.c will be completely removed.
The fcoe transport code files are completely removed in next
patch to keep this patch simple for reviewing.
[This patch is an update to a previous patch. This update
resolves a build error as well as fixes a defect related to
not calling fc_release_transport().]
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch adds support for dynamically created Rx threads
upon CPU hotplug events.
There were existing synchronization problems that this patch
attempts to resolve. The main problem had to do with fcoe_rcv()
running in a different context than the hotplug notifications.
This opened the possiblity that fcoe_rcv() would target a Rx
thread for a skb. However, that thread could become NULL if
the CPU was made offline.
This patch uses the Rx queue's (a skb_queue) lock to protect
the thread it's associated with and we use the 'thread' member
of the fcoe_percpu_s to determine if the thread is ready to
accept new skbs.
The patch also attempts to do a better job of cleaning up, both
if hotplug registration fails as well as when the module is
removed.
Contribution provided by Joe Eykholt <jeykholt@cisco.com> to
fix incorrect use of __cpuinitdata.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Remove the hotplug creation of dev_stats, we allocate for all possible CPUs
now when we allocate the lport.
v2: Durring the 2.6.30 merge window, before these patches were comitted,
'percpu_ptr' was renamed 'per_cpu_ptr'. This latest update updates this
patch for the name change.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Convert fcoe_percpu array to use the per-cpu variables
that the kernel provides. Use the kernel's functions to
access this structure.
The cpu member of the fcoe_percpu_s is no longer needed,
so this patch removes it too.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Currently the skb_queue is initialized every time the associated
CPU goes online. This patch has libfcoe initializing the skb_queue
for all possible CPUs when the module is loaded.
This patch also re-orders some declarations in the fcoe_rcv()
function so the structure declarations are grouped before
the primitive declarations.
Lastly, this patch converts all CPU indicies to use unsigned int
since CPU indicies should not be negative.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Remove the creation of the symlink from the device to
it's class. On modern systems this is already created by
a udev rule and would WARN on load. On old systems it is
not needed, none of the current osd user-mode tools use
this link.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
A fix for a very serious and stupid bug in osd_initiator. It
used to call blk_put_request() regardless of if it was from
the end_io callback or if called after a sync execution.
It should call the unlocked version __blk_put_request() instead.
Also fixed is the remove of _abort_unexecuted_bios hack, and use of
blk_end_request(,-ERROR,) to deallocate half baked requests. I've
audited the code and it should be safe.
Reported and
Tested-by: Xu Yang <onlyxuyang@qq.com>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We have a problem with recovered error handling in that any command
which goes down as BLOCK_PC but which returns a sense code of RECOVERED
ERROR gets completed with -EIO. For actual SG_IO commands, this doesn't
matter at all, since the error return code gets dropped in favour of
req->errors which contain the SCSI completion code.
However, if this command is part of the block system, then it will pay
attention to the returned error code. In particularly if a SYNCHRONIZE
CACHE from a barrier command completes with RECOVERED ERROR, the
resulting -EIO on the barrier causes block to error the request and
return it to the filesystem. Fix this by converting the -EIO for
recovered error to zero, plus remove the printing of this from sd and sr
so the message isn't double printed.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
aic79xx leaves timers inserted when ahd_init() (which inserts
two timers at its very end) succeeds but ahd_pci_map_int()
fails. In this case ahd->init_level gets incremented to 5 only
when that function succeeds, but ahd_free() calls ahd_shutdown()
only when ahd->init_level == 5, and ahd_shutdown() is where the
timers get removed. Since the freeing of the IRQ is not controlled
by ahd->init_level, we should increment init_level prior to
calling ahd_pci_map_int().
Reported-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
FLTDS provides FLT address in the byte address format,
convert it to dword address for further use.
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
In addition to checking for potentially unnecessary iomem
readX()/writeX() operations, a pci_channel_io_perm_failure should
not trigger a full internal removal. Found during additional
testing with pSeries blade systems.
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
As updates will occur using low-level option-rom manipulation
routines.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Firmware semantics changed for 24xx and above ISPs in their
handling of the specified execution-throttle passed during
firmware initialization. The original codes use of a theoretical
maximum (0xffff, as carried over from earlier ISPs) could in fact
act as a throttle in some circumstances. Now set the value based
of the firmware's own 'resource' (exchange IOCBs) capabilities.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The original code to 'resize request-queues' based on iocb-counts
and employed during early ISP23xx testing was too
overly-pessimistic with regards to latencies in the firmware
pulling requests. Recent ISPs can easily keep up processing a
stream of commands from an abbreviated (effectively, half the
original size) queue.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Rather than assuming a particular layout of the data. Applies to
recent ISPs only.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When IRQs are shared by multiple controllers and if the first one
to register does not disable the IRQ, then IRQ will be enabled
for all other controllers by default, irrespective of their
setting. With IRQF_DISABLED registration, the driver interrupt
routine was called with interrupt enabled always. Disbaling the
registration with IRQF_DISABLED, since driver code is re-entrant
safe and all critical sections are guarded with interrupt safe
locks.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Interface allows for the update of onboard EDC firmware
present on mezzanine ISP25xx type cards.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
In handling the RMW semantics needed to update regions not
falling on a sector boundary.
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
General cleanup of extraneous/legacy crud.
Additional cleanups and
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
For ISP24xx and above the ISP-abort after flash update is not
needed, as the only purpose it was serving was to update the boot
code and firmware versions in the scsi_qla_host_t structure. Now
an update of the versions will be done in the write-vpd path.
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Additional cleanups and
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Additional cleanups and
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Ensure that an ISP-abort has completed before performing any
update. After the update do not wait for an ISP-abort completion,
instead just wait until the ISP is reset. This avoids long
delays due to waiting for loop ready in qla2x00_abort_isp().
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Additional cleanups and
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Given the low-level interface varies from one flash-part
manufacturer to the next, the Flash-Access-Control (FAC) mailbox
command makes the specific flash type transparent to the driver
by encapsulating a basic set of accessor and update routines.
Use these new routines where applicable by querying FAC opcode
get-sector-size at init-time.
Additional cleanups and
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Since the routines can/will use resources such as devices and
rports that aren't valid after midlayer tear-down, correct this
potential race, by stopping the offending during the early stages
of the remove() callback.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
As all commands queued on the physical HBA should be aborted and
returned to the upper-layers.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reflects layout and format of latest specification.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Since in some circumstances, login-retries may be occuring in the
background via the DPC routine. This race, in the inadvertant
setting of the loop-id to 'NONE' breaks the existing retry logic.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Recent ISPs use this data to configure FCF information.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
With recent ISPs loading firmware from flash, a flash-update to
the firmware-image region with a follow-on reset will reload the
new image.
Original caching of data only made sense when firmware was bound
with the driver.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The pcihdr variable is used to find valid boot code image to get
FC boot code versions from flash. The pcihdr variable should be
byte aligned.
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
fce_size should be calculated based on the FCE_SIZE #define.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Earlier refactoring codes missed passing the proper vha structure
and instead passed the 'hardware-descriptor' ha.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Post refactoring/multi-queue additions essentially eliminated the
need for separate ISP24XX+ queuecommand as isp_ops contains a
function pointer to the associated 'start_scsi()' operation.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Original code used an overabundance of indirect pointers to
function helpers. Instead, the driver can exploit the immutable
properties of a queue's ISP-association and ID, which are both
known at queue initialization-time.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Bump driver version to 1.0.5.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The ibmvfc driver currently breaks the CRQ and essentially
resets the entire virtual FC adapter, killing all outstanding
ops to all attached targets, if an ADISC times out during target
discover/rediscovery. This patch adds some code to cancel the
ADISC if it times out, which prevents a single ADISC timeout from
affecting the other devices attached to the fabric.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Set show_host_maxframe_size so that maxframe_size gets exported in
sysfs for the host.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The ibmvfc driver really does not handle dynamically changing disc_threads.
To change this dynamically would cause confusion in the driver regarding
the number of event structs allocated. Fix this by simply not allowing
disc_threads to be changed at runtime.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch fixes a problem of possible dropped interrupts. Currently,
the ibmvfc driver has a race condition where after ibmvfc_interrupt
gets run, the platform code clears the interrupt. This can result in
lost interrupts and, in worst case scenarios, result in command
timeouts. Fix this by implementing a tasklet similar to what the
ibmvscsi driver does so that interrupt processing is no longer done in
the actual interrupt handler, which eliminates the race.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Setting ->owner as done currently (pde->owner = THIS_MODULE) is racy
as correctly noted at bug #12454. Someone can lookup entry with NULL
->owner, thus not pinning enything, and release it later resulting
in module refcount underflow.
We can keep ->owner and supply it at registration time like ->proc_fops
and ->data.
But this leaves ->owner as easy-manipulative field (just one C assignment)
and somebody will forget to unpin previous/pin current module when
switching ->owner. ->proc_fops is declared as "const" which should give
some thoughts.
->read_proc/->write_proc were just fixed to not require ->owner for
protection.
rmmod'ed directories will be empty and return "." and ".." -- no harm.
And directories with tricky enough readdir and lookup shouldn't be modular.
We definitely don't want such modular code.
Removing ->owner will also make PDE smaller.
So, let's nuke it.
Kudos to Jeff Layton for reminding about this, let's say, oversight.
http://bugzilla.kernel.org/show_bug.cgi?id=12454
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (422 commits)
[ARM] 5435/1: fix compile warning in sanity_check_meminfo()
[ARM] 5434/1: ARM: OMAP: Fix mailbox compile for 24xx
[ARM] pxa: fix the bad assumption that PCMCIA sockets always start with 0
[ARM] pxa: fix Colibri PXA300 and PXA320 LCD backlight pins
imxfb: Fix TFT mode
i.MX21/27: remove ifdef CONFIG_FB_IMX
imxfb: add clock support
mxc: add arch_reset() function
clkdev: add possibility to get a clock based on the device name
i.MX1: remove fb support from mach-imx
[ARM] pxa: build arch/arm/plat-pxa/mfp.c only when PXA3xx or ARCH_MMP defined
Gemini: Add support for Teltonika RUT100
Gemini: gpiolib based GPIO support v2
MAINTAINERS: add myself as Gemini architecture maintainer
ARM: Add Gemini architecture v3
[ARM] OMAP: Fix compile for omap2_init_common_hw()
MAINTAINERS: Add myself as Faraday ARM core variant maintainer
ARM: Add support for FA526 v2
[ARM] acorn,ebsa110,footbridge,integrator,sa1100: Convert asm/io.h to linux/io.h
[ARM] collie: fix two minor formatting nits
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: irq_node.handler() should return irqreturn_t
m68k: section mismatch fixes: Atari SCSI
m68k: section mismatch fixes: DMAsound for Atari
MAINTAINERS: Replace dead link to m68k CVS repository by link to new git repository
m68k: mac - Add SWIM floppy support
m68k: mac - Add a new entry in mac_model to identify the floppy controller type.
m68k: Add install target
* 'bkl-removal' of git://git.lwn.net/linux-2.6:
Rationalize fasync return values
Move FASYNC bit handling to f_op->fasync()
Use f_lock to protect f_flags
Rename struct file->f_ep_lock
The patch from Ming Lei <tom.leiming@gmail.com> entitled:
platform driver: fix incorrect use of 'platform_bus_type' with 'struct devic
introduced the following warnings on m68k, as `dev' is now a `struct
platform_device *' instead of a `struct device *':
| drivers/scsi/a4000t.c:64: warning: passing argument 3 of 'NCR_700_detect' from incompatible pointer type
| drivers/scsi/mvme16x_scsi.c:67: warning: passing argument 3 of 'NCR_700_detect' from incompatible pointer type
| drivers/scsi/bvme6000_scsi.c:61: warning: passing argument 3 of 'NCR_700_detect' from incompatible pointer type
I think the below is missing (untested on real hardware).
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the bug reported in
http://bugzilla.kernel.org/show_bug.cgi?id=11681.
"Lots of device drivers register a 'struct device_driver' with
the '.bus' member set to '&platform_bus_type'. This is wrong,
since the platform_bus functions expect the 'struct device_driver'
to be wrapped up in a 'struct platform_driver' which provides
some additional callbacks (like suspend_late, resume_early).
The effect may be that platform_suspend_late() uses bogus data
outside the device_driver struct as a pointer pointer to the
device driver's suspend_late() function or other hard to
reproduce failures."(Lothar Wassmann)
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Should be using strncmp as the data from user space may be unterminated
(Bug #8004)
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds retry for NOT_READY check condition - Quiesce in
progress (02/A1/02)
Signed-off-by: Vijay Chauhan<vijay.chauhan@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The ioc_list global symbol is already used in 1st generation mpt
fusion drivers, so this patch makes it unique in the 2nd generation
driver. I've checked the entire sources, and I don't see any other
global system missing the mpt2sas_xxx prefix.
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
sd_revalidate ends up being called several times during device setup.
With this patch we print everything during the first scan. Subsequent
invocations will only print a message if the parameter in question has
actually changed (LUN capacity has increased, etc.).
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
New features are being added to the READ CAPACITY 16 results, so we
want to issue it in preference to READ CAPACITY 10. Unfortunately, some
devices misbehave when they see a READ CAPACITY 16, so we restrict this
command to devices which claim conformance to SPC-3 (aka SBC-2), or claim
they have features which are only reported in the READ CAPACITY 16 data.
The READ CAPACITY 16 command is optional, even for SBC-2 devices, so
we fall back to READ CAPACITY 10 if READ CAPACITY 16 fails.
[jejb: don't error if device supports SBC-2 but doesn't support RC16]
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Tested-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Most fasync implementations do something like:
return fasync_helper(...);
But fasync_helper() will return a positive value at times - a feature used
in at least one place. Thus, a number of other drivers do:
err = fasync_helper(...);
if (err < 0)
return err;
return 0;
In the interests of consistency and more concise code, it makes sense to
map positive return values onto zero where ->fasync() is called.
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6: (31 commits)
[SCSI] qla2xxx: Update version number to 8.03.00-k4.
[SCSI] qla2xxx: Correct overwrite of pre-assigned init-control-block structure size.
[SCSI] qla2xxx: Correct truncation in return-code status checking.
[SCSI] qla2xxx: Correct vport delete bug.
[SCSI] qla2xxx: Use correct value for max vport in LOOP topology.
[SCSI] qla2xxx: Correct address range checking for option-rom updates.
[SCSI] fcoe: Change fcoe receive thread nice value from 19 (lowest priority) to -20
[SCSI] fcoe: fix handling of pending queue, prevent out of order frames (v3)
[SCSI] fcoe: Out of order tx frames was causing several check condition SCSI status
[SCSI] fcoe: fix kfree(skb)
[SCSI] fcoe: ETH_P_8021Q is already in if_ether and fcoe is not using it anyway
[SCSI] libfc: do not change the fh_rx_id of a recevied frame
[SCSI] fcoe: Correct fcoe_transports initialization vs. registration
[SCSI] fcoe: Use setup_timer() and mod_timer()
[SCSI] libfc, fcoe: Remove unnecessary cast by removing inline wrapper
[SCSI] libfc, fcoe: Cleanup function formatting and minor typos
[SCSI] libfc, fcoe: Fix kerneldoc comments
[SCSI] libfc: Cleanup libfc_function_template comments
[SCSI] libfc: check for err when recv and state is incorrect
[SCSI] libfc: rename rp to rdata in fc_disc_new_target()
...
The sd_read_capacity() function was about 180 lines long and
included a backwards goto and a tricky state variable. Splitting out
read_capacity_10() and read_capacity_16() (about 50 lines each) reduces
sd_read_capacity to about 100 lines and gets rid of the backwards goto
and the state variable. I've tried to avoid any behaviour change with
this patch.
[jejb: upped transfer request to standard recommended 32 for RC16]
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* This is new scsi lld device driver from LSI supporting the SAS 2.0
standard. I have split patchs by filename.
* Here is list of new 6gb host controllers:
LSI SAS2004
LSI SAS2008
LSI SAS2108
LSI SAS2116
* Here are the changes in the 4th posting of this patch set:
(1) fix compile errors when SCSI_MPT2SAS_LOGGING is not enabled
(2) add mpt2sas to the SCSI Mid Layer Makefile
(3) append mpt2sas_ to the naming of all non-static functions
(4) fix oops for SMP_PASSTHRU
(5) doorbell algorithm imported changes from windows driver
* Here are the changes in the 3rd posting of this patch set:
(1) add readl following writel from the function that disables interrupts
(2) replace 0xFFFFFFFFFFFFFFFFULL with ~0ULL
(3) when calling pci_enable_msix, only pass one msix entry (instead of 15).
(4) remove the "current HW implementation uses..... " comment in the sources
(5) merged bug fix for SIGIO/POLLIN notifcation; reported by the storlib team.
* Here are the changes in the 2nd posting of this patch set:
(1) use little endian types in the mpi headers
(2) merged in bug fix's from inhouse drivers.
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Tested-by: peter Bogdanovic <pbog@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The ch module is missing the scsi:t-0x08* alias that would cause it to
be auto-loaded when a device of that type if found by udev, requiring
udev to have a specific rule just for this one module. This patch adds
the alias.
Signed-off-by: Scott James Remnant <scott@canonical.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Limit function descriptions to be one line.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
If the iscsi eh fires when the current task is a nop, then
the task->sc pointer is null. fail_all_commands could
then try to do task->sc->device and oops. We actually do
not need to access the curr task in this path, because
if it is a cmd task the fail_command call will handle
this and if it is mgmt task then the flush of the mgmt
queues will handle that.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We do not need to have llds set the host no for the session's
parent, because we know the session's parent is going to be
the host. This removes it from the session creation callback
and converts the drivers.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The api for conn and session failures is akward because
one takes a conn from the lib and one takes a session
from the class. This syncs up the interfaces to use
structs from the lib.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The qdepth setting was useful when we needed libiscsi to verify
the setting. Now we just need to make sure if older tools
passed in zero then we need to set some default.
So this patch just has us use the sht->cmd_per_lun or if
for LLD does a host per session then we can set it on per
host basis.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We were using the shost work queue which ended up being
a little akward since all iscsi hosts need a thread for
scanning, but only drivers hooked into libiscsi need
a workqueue for transmitting. So this patch moves the
xmit workqueue to the lib.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We never should hit the lock up that is spit out when
lock dep is on and we logout. But we have been using the
shost work queue in a odd way. This patch has us use the
work queue for scanning instead of creating our own,
and this ends up also killing the lock dep warnings.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
There is no need to cap the queue depth in the modules. We set
this in userspace and can do that there. For performance testing
with ram based targets, this is helpful since we can have very
high queue depths.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This makes the logging a compile time option and replaces
the tcp_debug macro with a iscsi connection one that prints
out a driver model id prefix.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This makes the logging a compile time option and replaces
the scsi_debug and tcp_debug macro with session and connection ones
that print out a driver model id prefix.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This makes the logging a compile time option and replaces
the scsi_debug macro with session and connection ones
that print out a driver model id prefix.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Mark iscsi_tcp as being capable of bidirectional transfers. The
bsg interface checks this bit before attempting any bidirectional
commands.
Signed-off-by: Pete Wyckoff <pw@padd.com>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Memory freeing in iscsi_pool_free() looks wrong to me. Either q->pool
can be NULL and this should be tested before dereferencing it, or it
can't be NULL and it shouldn't be tested at all. As far as I can see,
the only case where q->pool is NULL is on early error in
iscsi_pool_init(). One possible way to fix the bug is thus to not
call iscsi_pool_free() in this case (nothing needs to be freed anyway)
and then we can get rid of the q->pool check.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
If LLD supports FCCRC offload, it should set ip_summed to be
CHECKSUM_UNNECESSARY so we don't have to do CRC check again.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This adds implementation of ddp_setup()/ddp_done() in fcoe_sw for its
fcoe_sw_libfc_fcn_templ.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When LLD supports direct data placement (ddp) for large receive of an scsi
i/o coming into fc_fcp, we call into libfc_function_template's ddp_setup()
to prepare for a ddp of large receive for this read I/O. When I/O is complete,
we call the corresponding ddp_done() to get the length of data ddped as well
as to let LLD do clean up.
fc_fcp_ddp_setup()/fc_fcp_ddp_done() are added to setup and complete a ddped
read I/O described by the given fc_fcp_pkt. They would call into corresponding
ddp_setup/ddp_done implemented by the fcoe layer. Eventually, fcoe layer calls
into LLD's ddp_setup/ddp_done provided through net_device
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Change fcoe_xmit to setup gso for LLD LSO offload as well as CRC offload
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Make sure for large send is supported by LLD in outgoing FCP data, we are only
sending the lso_max a time in one single large send, since that is what
supported by LLD.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This checks if net_devices supports FCoE offload ops in netdev_ops and it
if it does, then sets up the corresponding flags in the associated fc_lport.
For large send offload, the maximum length supported in one large send is now
described by the added lso_max in fc_lport, which is setup initially from
netdev->gso_max_size.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This adds eth type ETH_P_FCOE for Fibre Channel over Ethernet (FCoE),
consequently, the ETH_P_FCOE from fc_fcoe.h and fcoe skb->protocol
is not set as ETH_P_FCOE.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: David Miller <davem@davemloft.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fix compile warnings:
drivers/scsi/zalon.c: In function `zalon_probe':
drivers/scsi/zalon.c:140: warning: passing arg 1 of `dev_driver_string' from incompatible pointer type
drivers/scsi/zalon.c:140: warning: passing arg 1 of `dev_name' from incompatible pointer type
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
This patch is to add retry for mode select if mode select command is
returned with sense NO_SENSE, UNIT_ATTENTION, ABORTED_COMMAND,
NOT_READY(02/04/01). This patch reorganise the sense keys from if-else
to switch-case format for better maintainability.
Signed-off-by: Vijay Chauhan <vijay.chauhan@lsi.com>
Acked-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The SCSI core calls scsi_proc_hostdir_add() from within
scsi_host_alloc(), but the corresponding scsi_proc_hostdir_rm()
routine is called from within scsi_remove_host(). As a result, if a
host is allocated and then deallocated without ever being registered,
the host's directory in /proc is leaked.
This patch (as1181b) fixes this bug in the SCSI core by moving
scsi_proc_hostdir_rm() into scsi_host_dev_release().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
sym53c8xx prints a negotiation message after every check condition.
This can add up to a lot of messages for removable-medium devices
(CD-ROM, tape drives, etc.) that are being polled, since they return
check condition when no medium is present. This patch suppresses the
negotiation message if it would be the same as the last one printed.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
sym53c8xx uses a command queue depth of 2 for untagged devices,
without good reason. This _mostly_ seems to work ok, but it has
caused me some subtle problems. For example, I have an application
where one thread sends write commands to a tape drive, and another
thread sends log sense polling commands. With a queue depth of
2, the polling commands end up being starved for long periods of
time while multiple write commands are serviced (this may also be
related to the fact the the sg driver queues commands in LIFO order).
This problem is fixed by changing the queue depth to 1 for untagged
devices. I have tested this change extensively with many different
tape drives, medium changers, and disk drives (disk drives of course
use tagged commands and are therefore unaffected by this patch).
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
sym_init_device() doesn't check if pci_iomap() fails. It also tries
to map device RAM without first checking FE_RAM.
1) Move some initialization from sym_init_device() to the top of
sym2_probe().
2) Rename sym_init_device() to sym_iomap_device().
3) Call sym_iomap_device() after sym_check_supported() instead of
before so that device->chip.features will be set.
4) Check FE_RAM in sym_iomap_device() before mapping RAM.
5) If sym_iomap_device() cannot map registers, then abort.
6) If sym_iomap_device() cannot map RAM, then fall back to not using
RAM and continue.
7) Remove the check for FE_RAM in sym_attach() since dev->ram_base
is now always set correctly.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
During sym2_probe(), sym_init_device() does pci_iomap(), but there is
no corresponding pci_iounmap() if an error occurs before sym_attach()
copies sym_device::s.{ioaddr,ramaddr} to np.
1) Add the sym_iounmap_device() function.
2) Call sym_iounmap_device() if an error occurs between
sym_init_device() and the time sym_attach() allocates np.
3) Make sym_attach() copy sym_device::s.{ioaddr,ramaddr} to np before
calling any function that can fail so that sym_free_resources()
will do the unmap instead of sym_iounmap_device().
Also fixed by this patch:
During sym2_probe(), if sym_check_raid() returns nonzero, then
pci_release_regions() is never called.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
If sym_attach() gets an error at or before request_irq(), then
sym_free_resources() will call free_irq() for an unregistered
interrupt handler.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
If sym_attach() fails to allocate np, the error path will dereference
a NULL pointer for printk.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch fixes two bugs:
1) rmmod sym53c8xx uses shost after freeing it with
scsi_put_host(shost).
2) insmod sym53c8xx doesn't call scsi_put_host(shost) if
scsi_add_host() fails, causing a memory leak on the error path.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Expose the debug and fastfail parameters to /sys/module/ipr/parameters such
that they can be enabled/disabled at run time.
Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch (as1188) combines the tests for decrementing a drive's
reported capacity and expands the comment. It also adds an
informational message to the system log, informing the user when the
reported value has been changed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This replaces the own list management for struct sg_fd with the
standard list_head structure.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This changes sg_build_indirect() to use ALIGN macro instead of
calculating by hand.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
!ep->esb_stat is either 1 or 0, and the rightmost bit of ESB_ST_COMPLETE is
always 0, making the result of !ep->esb_stat & ESB_ST_COMPLETE always 0.
Thus parentheses around the argument to ! seem needed.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@ expression E; constant C; @@
(
!E & !C
|
- !E & C
+ !(E & C)
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Very old OSC's Target had a BUG in the Get/Set attributes where
it was looking in the wrong places for attribute lists length.
If used with the open-osd initiator, the initiator would dereference
a NULL pointer when retrieving system_information attributes.
Checks are added that retrieval of each attribute is successful
before accessing its value.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This fixes the following oops:
http://marc.info/?l=linux-kernel&m=123316111415677&w=2
You can reproduce this bug by interrupting a program before a sg
response completes. This leads to the special sg state (the orphan
state), then sg calls blk_put_request in interrupt (rq->end_io).
The above bug report shows the recursive lock problem because sg calls
blk_put_request in interrupt. We could call __blk_put_request here
instead however we also need to handle blk_rq_unmap_user here, which
can't be called in interrupt too.
In the orphan state, we don't need to care about the data transfer
(the program revoked the command) so adding 'just free the resource'
mode to blk_rq_unmap_user is a possible option.
I prefer to avoid complicating the blk mapping API when possible. I
change the orphan state to call sg_finish_rem_req via
execute_in_process_context. We hold sg_fd->kref so sg_fd doesn't go
away until keventd_wq finishes our work. copy_from_user/to_user fails
so blk_rq_unmap_user just frees the resource without the data
transfer.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The ibmvfc driver currently always sets the role of all rports
to FC_PORT_ROLE_FCP_TARGET, which is not correct for other initiators.
This can cause problems if other initiators are on the fabric
when we then try to scan the rport for LUNs. Fix this by looking
at the service parameters returned in the PRLI to set the roles
appropriately. Also look at the returned service parameters to
decide whether or not we were actually able to successfully log into
the target.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
During device discovery read capacity fails with 0x068b02 and sets the
device size to 0. As a reason any I/O submitted to this path gets
killed at sd_prep_fn with BLKPREP_KILL. This patch is to retry for
0x068b02
Signed-off-by: Vijay Chauhan <vijay.chauhan@lsi.com>
Acked-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Adds a message to the error table for an error that wasn't previously handled.
In some cases the I/O Adapter will detect an error condition and mark a block
as "logically bad".
Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When we switch controllers the Intel Multi-Flex reports
REPORTED_LUNS_DATA_HAS_CHANGED. This patch just has us
retry the command.
Signed-off-by: Ilgu Hong <ilgu.hong@promise.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This adds the Intel Multi-Flex device to scsi_dh_alua's
scsi_dh_devlist, so the module attaches to these devs.
Signed-off-by: Ilgu Hong <ilgu.hong@promise.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The buf[i] is a byte but we are only asking 4 bits off the
group_id. This patch has us take off a byte.
Signed-off-by: Ilgu Hong <ilgu.hong@promise.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
No one uses scsi_execute_async with data transfer now. We can remove
scsi_req_map_sg.
Only scsi_eh_lock_door uses scsi_execute_async. scsi_eh_lock_door
doesn't handle sense and the callback. So we can remove
scsi_io_context too.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This replaces scsi_execute_async with the block layer API. st does the
same thing so it might make sense to have something like libst (there
are other things that os and osst can share).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Willem Riede <osst@riede.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This simiplifies the buffer management; all the buffers in osst_buffer
become the same size. This is necessary to use the block layer API (sg
driver was modified in the same way) since the block layer API takes
the same size page frames instead of scatter gatter.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Willem Riede <osst@riede.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
OSD in kernel source code is assumed to be at:
drivers/scsi/osd/ with its own Makefile and Kconfig
Add includes to them from drivers/scsi Makefile and Kconfig
Add OSD to MAINTAINERS file
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Reviewed-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Implementation of the osd_req_decode_sense() API. Can be called by
library users to decode what failed in command executions.
Add SCSI_OSD_DPRINT_SENSE Kconfig variable. Possible values are:
0 - Do not print any errors to messages file <KERN_ERR>
1 - (Default) Print only decoded errors that are not recoverable.
Recoverable errors are those that the target has complied with
the request but with a warning. For example read passed end of
object will return zeros after the last valid byte.
2- Print all errors.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Auto detect an OSDv2 or OSDv1 target at run time. Note how none
of the OSD API calls change. The tests do not know what device
version it is.
This test now passes against both the IBM-OSD-SIM OSD1 target
as well as OSC's OSD2 target.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Reviewed-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Add support for OSD2 at run time. It is now possible to run with
both OSDv1 and OSDv2 targets at the same time. The actual detection
should be preformed by the security manager, as the version is encoded
in the capability structure.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Reviewed-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Some commands declared in header are not yet implemented. Put them
as stubs in .c file, just so they take their place in the file
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Reviewed-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Add support for the various List-objects commands. List-partitions-in-device,
List-collections-in-partition, List-objects-in-partition,
List-objects-in-collection. All these support partial listing and continuation.
Add support for the different Flush commands and options.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Reviewed-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Layout the signing of OSD's CDB and all-data security modes. The actual
code for signing the data and CDB is missing, but the code flow and the extra
buffer segments are all in place.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Reviewed-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Support for both List-Mode and Page-Mode osd attributes. One of
these operations may be added to most other operations.
Define the OSD standard's attribute pages constants and structures
(osd_attributes.h)
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Reviewed-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Kernel clients like exofs can retrieve struct osd_dev(s)
by means of below API.
+ osduld_path_lookup() - given a path (e.g "/dev/osd0") locks and
returns the corresponding struct osd_dev, which is then needed
for subsequent libosd use.
+ osduld_put_device() - free up use of an osd_dev.
Devices can be shared by multiple clients. The osd_uld_device's
life time is governed by an embedded kref structure.
The osd_uld_device holds an extra reference to both it's
char-device and it's scsi_device, and will release these just
before the final deallocation.
There are three possible lock sources of the osd_uld_device
1. First and for most is the probe() function called by
scsi-ml upon a successful login into a target. Released in release()
when logout.
2. Second by user-mode file handles opened on the char-dev.
3. Third is here by Kernel users.
All three locks must be removed before the osd_uld_device is freed.
The MODULE has three lock sources as well:
1. scsi-ml at probe() time, removed after release(). (login/logout)
2. The user-mode file handles open/close.
3. Import symbols by client modules like exofs.
TODO:
This API is not enough for the pNFS-objects LD. A more versatile
API will be needed. Proposed API could be:
struct osd_dev *osduld_sysid_lookup(const char id[OSD_SYSTEMID_LEN]);
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Add a Linux driver module that registers as a SCSI ULD and probes
for OSD type SCSI devices.
When an OSD-type SCSI device is found a character device is created
in the form of /dev/osdX - where X goes from 0 up to hard coded 64.
The Major character device number used is 260.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Reviewed-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
