Commit 549e8152de ("powerpc: Make the
64-bit kernel as a position-independent executable") added lines to
vmlinux.lds.S to add the extra sections needed to implement a
relocatable kernel. However, those lines seem to trigger a bug in
older versions of GNU ld (such as 2.16.1) when building a
non-relocatable kernel. Since ld 2.16.1 is still a popular choice for
cross-toolchains, this adds an #ifdef to vmlinux.lds.S so the added
lines are only included when building a relocatable kernel.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The __kdump_flag ABI is overly constraining for future development.
As of 2.6.27, the kernel entry point has 4 constraints: Offset 0 is
the starting point for the master (boot) cpu (entered with r3 pointing
to the device tree structure), offset 0x60 is code for the slave cpus
(entered with r3 set to their device tree physical id), offset 0x20 is
used by the iseries hypervisor, and secondary cpus must be well behaved
when the first 256 bytes are copied to address 0.
Placing the __kdump_flag at 0x18 is bad because:
- It was taking the last 8 bytes before the iseries hypervisor data.
- It was 8 bytes for a boolean flag
- It had no way of identifying that the flag was present
- It does leave any room for the master to add any additional code
before branching, which hurts debug.
- It will be unnecessarily hard for 32 bit code to be common (8 bytes)
Now that we have eliminated the use of __kdump_flag in favor of
the standard is_kdump_kernel(), this flag only controls run without
relocating the kernel to PHYSICAL_START (0), so rename it __run_at_load.
Move the flag to 0x5c, 1 word before the secondary cpu entry point at
0x60. Initialize it with "run0" to say it will run at 0 unless it is
set to 1. It only exists if we are relocatable.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
linux/crash_dump.h defines is_kdump_kernel() to be used by code that
needs to know if the previous kernel crashed instead of a (clean) boot
or reboot.
This updates the just added powerpc code to use it. This is needed
for the next commit, which will remove __kdump_flag.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Commit 54622f10a6 ("powerpc: Support for
relocatable kdump kernel") added a magic flag value in a register to
tell purgatory that it should be a panic kernel. This part is wrong
and is reverted by this commit.
The kernel gets a list of memory blocks and a entry point from user space.
Its job is to copy the blocks into place and then branch to the designated
entry point (after turning "off" the mmu).
The user space tool inserts a trampoline, called purgatory, that runs
before the user supplied code. Its job is to establish the entry
environment for the new kernel or other application based on the contents
of memory. The purgatory code is compiled and embedded in the tool,
where it is later patched using the elf symbol table using elf symbols.
Since the tool knows it is creating a purgatory that will run after a
kernel crash, it should just patch purgatory (or the kernel directly)
if something needs to happen.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The current defconfig for Linkstation/Kuroboxes has the "Disable Heap
Randomization" option enabled.
Since some of these machines are facing the internet, it helps to have
heap randomization enabled. This patch enables it.
Signed-off-by: Rogério Brito <rbrito@ime.usp.br>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Since Linkstations and Kuroboxes often have *very* little memory (as
they are embedded systems), it is desirable to get their kernels
compiled optimized for size.
Signed-off-by: Rogério Brito <rbrito@ime.usp.br>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The i2c bus defn is broken on linkstation / kurobox machines since at
least 2.6.27. Fix it. Also remove CONFIG_SERIAL_OF_PLATFORM, which, if
enabled, breaks the serial console after the
"console handover: boot [udbg0] -> real [ttyS1]" message.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix the HCU4 Kconfig option to 'default n'. We don't want the
board to always be enabled for other board defconfigs.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
If CONFIG_AMIGA_BUILTIN_SERIAL=m, I get the following warnings:
| drivers/char/amiserial.c: At top level:
| drivers/char/amiserial.c:2138: warning: data definition has no type or storage class
| drivers/char/amiserial.c:2138: warning: type defaults to 'int' in declaration of 'console_initcall'
| drivers/char/amiserial.c:2138: warning: parameter names (without types) in function declaration
| drivers/char/amiserial.c:2134: warning: 'amiserial_console_init' defined but not used
because console_initcall() is not defined (nor really sensible) in the
modular case.
So disable serial console support if the driver is modular.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In commit f337b9c583 ("epoll: drop
unnecessary test") Thomas found that there is an unnecessary (always
true) test in ep_send_events(). The callback never inserts into
->rdllink while the send loop is performed, and also does the
~EP_PRIVATE_BITS test. Given we're holding the mutex during this time,
the conditions tested inside the loop are always true.
HOWEVER.
The test "!ep_is_linked(&epi->rdllink)" wasn't there because we insert
into ->rdllink, but because the send-events loop might terminate before
the whole list is scanned (-EFAULT).
In such cases, when the loop terminates early, and when a (leftover)
file received an event while we're performing the lockless loop, we need
such test to avoid to double insert the epoll items. The list_splice()
done a few steps below, will correctly re-insert the ones that were left
on "txlist".
This should fix the kenrel.org bugzilla entry 11831.
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some userland apps seem to pass in a "0" for the seconds, and several
seconds worth of usecs to select(). The old kernels accepted this just
fine, so the new kernels must too.
However, due to the upscaling of the microseconds to nanoseconds we had
some cases where we got math overflow, and depending on the GCC version
(due to inlining decisions) that actually resulted in an -EINVAL return.
This patch fixes this by adding the excess microseconds to the seconds
field.
Also with thanks to Marcin Slusarz for spotting some implementation bugs
in the diagnostics patches.
Reported-by: Carlos R. Mafra <crmafra2@gmail.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The default for the regulatory compatibility option is wrong;
if you picked the default you ended up with a non-functional wifi
system (at least I did on Fedora 9 with iwl4965).
I don't think even the October 2008 releases of the various distros
has the new userland so clearly the default is wrong, and also
we can't just go about deleting this in 2.6.29...
Change the default to "y" and also adjust the config text a little to
reflect this.
This patch fixes regression #11859
With thanks to Johannes Berg for the diagnostics
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
/scratch/sfr/next/kernel/cgroup.c: In function 'cgroup_tasks_start':
/scratch/sfr/next/kernel/cgroup.c:2107: warning: unused variable 'i'
Introduced in commit cc31edceee "cgroups:
convert tasks file to use a seq_file with shared pid array".
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
hwmon: (abituguru3) enable DMI probing feature on AW9D-MAX
hwmon: (abituguru3) Cosmetic whitespace fixes
hwmon: (adt7473) Fix voltage conversion routines
hwmon: (lm90) Add support for the LM99 16 degree offset
hwmon: (lm90) Fix handling of hysteresis value
hwmon-vid: Add support for AMD family 10h CPUs
hwmon: (w83781d) Fix linking when built-in
This reverts commit 7bf6bf4803.
The code has both a short existence and an increasing track of failures
despite some work to amend it for -rc1. It is not just a matter of
reading the eeprom: sometimes the eeprom is read correctly, then the mac
address is not written correctly back into the mac registers.
Some chipsets seem to work reliably but it is not clear at this point if
the code can simply be made to work on a per-chipset basis and post -rc1
is not the place where I want to experiment these things.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
a) semicolon before the function body is a bad idea
b) it's const struct foo, not struct const foo
c) incidentally, it's ecard_remove_driver(), not ecard_unregister_driver()
d) compiling is occasionally useful.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If you use KCONFIG_ALLCONFIG (even with empty file) you get broken
allmodconfig/allyesconfig; CONFIG_MODULES gets turned off, with obvious
massive fallout.
Breakage had been introduced when conf_set_all_new_symbols() got used
for allmodconfig et.al.
What happens is that sym_calc_value(modules_sym) done in
conf_read_simple() sets SYMBOL_VALID on both modules_sym and MODULES.
When we get to conf_set_all_new_symbols(), we set sym->def[S_DEF_USER]
on everything, but it has no effect on sym->curr for the symbols that
already have SYMBOL_VALID - these are stuck.
Solution: use sym_clear_all_valid() in there. Note that it makes
reevaluation of modules_sym redundant - sym_clear_all_valid() will do
that itself.
[ Fixes http://bugzilla.kernel.org/show_bug.cgi?id=11512, says Alexey ]
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Switch the AW9D-MAX over from port probing to the preferred DMI
probe method.
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk>
Tested-by: Justin Piszcz <jpiszcz@lucidpixels.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
As the probable result of zealous copy/pasting, many supported boards
contain sensor names with trailing whitespace. Though this is not a
huge problem, it is inconsistent with other sensor names, and with
other similar hwmon drivers.
Additionally, the DMI nag message added in 2.6.27 was missing a
space between two sentence fragments -- might as well clean that up
too.
Doesn't alter any kernel text, just data.
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk>
Reported-by: Justin Piszcz <jpiszcz@lucidpixels.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix voltage conversion routines. Based on an earlier patch from
Paulius Zaleckas.
According to the datasheet voltage is scaled with resistors and
value 192 is nominal voltage. 0 is 0V.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Cc: Darrick J. Wong <djwong@us.ibm.com>
The LM99 differs from the LM86, LM89 and LM90 in that it reports
remote temperatures (temp2) 16 degrees lower than they really are. So
far we have been cheating and handled this in userspace but it really
should be handled by the driver directly.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
There are several problems in the way the hysteresis value is handled
by the lm90 driver:
* In show_temphyst(), specific handling of the MAX6646 is missing, so
the hysteresis is reported incorrectly if the critical temperature
is over 127 degrees C.
* In set_temphyst(), the new hysteresis register value is written to
the chip but data->temp_hyst isn't updated accordingly, so there is
a short period of time (up to 2 seconds) where the old hystereris
value will be returned while the new one is already active.
* In set_temphyst(), the critical temperature which is used as a base
to compute the value of the hysteresis register lacks
device-specific handling. As a result, the value of the hysteresis
register might be incorrect for the ADT7461 and MAX6646 chips.
Fix these 3 bugs.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Nate Case <ncase@xes-inc.com>
The AMD family 10h CPUs use the same VID decoding table as the family
0Fh CPUs.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Rudolf Marek <r.marek@assembler.cz>
When w83781d is built-in, the final links fails with the following vague error
message:
`.exit.text' referenced in section `.init.text' of drivers/built-in.o: defined
in discarded section `.exit.text' of drivers/built-in.o
w83781d_isa_unregister() cannot be marked __exit, as it's also called from
sensors_w83781d_init(), which is marked __init.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: Fix duplicate entries returned from getdents() system call
ext3: Fix duplicate entries returned from getdents() system call
This reverts commit a802dd0eb5 by moving
the call to init_workqueues() back where it belongs - after SMP has been
initialized.
It also moves stop_machine_init() - which needs workqueues - to a later
phase using a core_initcall() instead of early_initcall(). That should
satisfy all ordering requirements, and was apparently the reason why
init_workqueues() was moved to be too early.
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a regression caused by commit d0156417, "ext4: fix ext4_dx_readdir
hash collision handling", where deleting files in a large directory
(requiring more than one getdents system call), results in some
filenames being returned twice. This was caused by a failure to
update info->curr_hash and info->curr_minor_hash, so that if the
directory had gotten modified since the last getdents() system call
(as would be the case if the user is running "rm -r" or "git clean"),
a directory entry would get returned twice to the userspace.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
This patch fixes the bug reported by Markus Trippelsdorf at:
http://bugzilla.kernel.org/show_bug.cgi?id=11844
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Fix a regression caused by commit 6a897cf4, "ext3: fix ext3_dx_readdir
hash collision handling", where deleting files in a large directory
(requiring more than one getdents system call), results in some
filenames being returned twice. This was caused by a failure to
update info->curr_hash and info->curr_minor_hash, so that if the
directory had gotten modified since the last getdents() system call
(as would be the case if the user is running "rm -r" or "git clean"),
a directory entry would get returned twice to the userspace.
This patch fixes the bug reported by Markus Trippelsdorf at:
http://bugzilla.kernel.org/show_bug.cgi?id=11844
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
The recent commit 2fca5ccf97 ("libata:
switch to using block layer tagging support") to enable support for
block layer tagging in libata was broken for non-NCQ devices
The block layer initializes the tag field to -1 to detect invalid uses
of a tag, and if the libata devices does NOT support NCQ, we just used
that field to index the internal command list. So we need to check for
-1 first and only use the tag field if it's valid.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Reported-by: Alexander Beregalov <a.beregalov@gmail.com>
Tested-by: Paul Mundt <lethal@linux-sh.org>
Tested-by: Dave Young <hidave.darkstar@gmail.com>
Tested-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix printk format warning:
drivers/pci/hotplug/acpiphp_ibm.c:207: warning: format '%08lx' expects type 'long unsigned int', but argument 3 has type 'long long unsigned int'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (29 commits)
tcp: Restore ordering of TCP options for the sake of inter-operability
net: Fix disjunct computation of netdev features
sctp: Fix to handle SHUTDOWN in SHUTDOWN_RECEIVED state
sctp: Fix to handle SHUTDOWN in SHUTDOWN-PENDING state
sctp: Add check for the TSN field of the SHUTDOWN chunk
sctp: Drop ICMP packet too big message with MTU larger than current PMTU
p54: enable 2.4/5GHz spectrum by eeprom bits.
orinoco: reduce stack usage in firmware download path
ath5k: fix suspend-related oops on rmmod
[netdrvr] fec_mpc52xx: Implement polling, to make netconsole work.
qlge: Fix MSI/legacy single interrupt bug.
smc911x: Make the driver safer on SMP
smc911x: Add IRQ polarity configuration
smc911x: Allow Kconfig dependency on ARM
sis190: add identifier for Atheros AR8021 PHY
8139x: reduce message severity on driver overlap
igb: add IGB_DCA instead of selecting INTEL_IOATDMA
igb: fix tx data corruption with transition to L0s on 82575
ehea: Fix memory hotplug support
netdev: DM9000: remove BLACKFIN hacking in DM9000 netdev driver
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
math-emu: Fix thinko in _FP_DIV
math-emu: Fix signalling of underflow and inexact while packing result.
sparc: Add checkstack support
sparc: correct section of current_pc()
sparc: correct section of apc_no_idle
sparc64: Fix race in arch/sparc64/kernel/trampoline.S
This cleanup removes the resource assignment in pci_read_bridge_bases()
since it has taken care by pci_alloc_child_bus() when allocating the bus:
/* Set up default resource pointers and names.. */
for (i = 0; i < PCI_BRIDGE_RES_NUM; i++) {
child->resource[i] = &bridge->resource[PCI_BRIDGE_RESOURCES+i];
child->resource[i]->name = child->name;
}
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch refines messages in shpchp module. The main changes are as
follows:
- remove the trailing "."
- remove __func__ as much as possible
- capitalize the first letter of messages
- show PCI device address including its domain
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
ide: drivers/ide/generic.c -> drivers/ide/ide-pci-generic.c
ide-disk: set non-rotational queue flag for SSD and CF devices
ide-cd: add TEAC CD-224E to the NO_AUTOCLOSE list
ide: Add tx4938ide driver (v2)
TXx9: Add TX4938 ATA support (v3)
ide: Add tx4939ide driver (v6)
ide: two more pci_ioremap_bar() conversions
pci: use pci_ioremap_bar() in drivers/ide
sgiioc4: use ide_host_add() (take 2)
sgiioc4: fix error cleanup path (take 2)
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] pxa: corgi backlight driver should not select ssp drivers
[ARM] 5321/1: Kirkwood: fix typo in Makefile
[ARM] 5320/1: fix assembly constraints in implementation of do_div()
[ARM] 5318/1: Swap the PRRR and NMRR values in proc-v7.S
[ARM] 5316/1: AT91: oops (regression) fix on gpio irq
[ARM] msm: vreg interface to msm7k pmic
[ARM] msm: dma: various basic dma improvements and bugfixes
[ARM] msm: clock: provide clk_*() api support for
[ARM] msm: clean up iomap and devices
[ARM] msm: add proc_comm support, necessary for clock and power control
[ARM] msm: rename ARCH_MSM7X00A to ARCH_MSM
[ARM] pxa/spitz: fix unbalance parenthesis in header file spitz.h
[ARM] pxa: update {corgi,spitz}_defconfig to favor SPI-based drivers
[ARM] pxa: fix the corgi_ssp.c dependency issue in {corgi,spitz}_defconfig
Revert "[ARM] pxa/corgi: remove now unused corgi_ssp.c and corgi_lcd.c"
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-backlight:
backlight: Add driver for Tabletkiosk Sahara TouchIT-213 Tablet PC
backlight: da903x: Add backlight driver for DA9030/DA9034
tosa: add support for bl/lcd driver
backlight: add support for Sharp SL-6000 LCD and backlight drivers
libata currently has a pretty dumb ATA_MAX_QUEUE loop for finding
a free tag to use. Instead of fixing that up, convert libata to
using block layer tagging - gets rid of code in libata, and is also
much faster.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We're getting a lot of storage drivers blamed for interrupt misrouting
issues. This patch provides a standard way of reporting the problem
... and, if possible, correcting it.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch refines messages in pciehp module. The main changes are as
follows:
- remove the trailing "."
- remove __func__ as much as possible
- capitalize the first letter of messages
- show PCI device address including its domain
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The original ARI support code has a compatibility problem with non-ARI
devices. If a device doesn't support ARI, turning on ARI forwarding on
its upper level bridge will cause undefined behavior.
This fix turns on ARI forwarding only when the subordinate devices
support it.
Tested-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The following patch fixes the regression in 2.6.27 that causes kernel
NULL pointer dereference at cpqphp driver probe time. This patch should
be backported to the .27 stable series.
Seems to have been introduced by
f46753c5e3.
The root cause of this problem seems that cpqphp driver calls
pci_hp_register() wrongly. In current implementation, cpqphp driver
passes 'ctrl->pci_dev->subordinate' as a second parameter for
pci_hp_register(). But because hotplug slots and it's hotplug controller
(exists as a pci funcion) are on the same bus, it should be
'ctrl->pci_dev->bus' instead.
Cc: <stable@kernel.org>
Tested-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Paul Mackerras
Milton Miller
Josh Boyer
Rogério Brito
Guennadi Liakhovetski
Linus Torvalds
Geert Uytterhoeven
Davide Libenzi
Arjan van de Ven
Stephen Rothwell
Francois Romieu
Al Viro
Alistair John Strachan
Jean Delvare
Theodore Ts'o
Jens Axboe
Randy Dunlap
Zhao, Yu
Taku Izumi
James Bottomley
Kenji Kaneshige