If no user settings are found it's pointless trying to
read them from flash. So skip that step.
This also fixes a compilation warning about uninitialized variables in
aic94xx.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Remove unnecessary check that disabled SIS pipe commands for SIS-32
devices. This change was sufficient to enable raw mode and send SIS
pipe commands for a 57B3 device.
Fixes: f8ee25d7d2 ("ipr: AF DASD raw mode implementation in ipr driver")
Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Reviewed-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Disable underlength error verification based on count of bytes actually
transferred for AF DASD devices when SIS pipe mode is enabled.
This avoids unexpected underlength errors when issuing some commands in
raw mode.
Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Reviewed-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Issue: When the disks are getting discovered and assigned device
handles by the kernel, a device block followed by an unblock
(due to broadcast primitives) issued by the driver is
interspersed by the kernel changing the state of the device.
Therefore the unblock by the driver results in a no operation
within the kernel API.
To fix this one, the below patch checks the return of the unblock API
and performs a block followed by an unblock to unfreeze the block
layer's I/O queue. Sufficient checks and prints are also added in the
driver to identify this condition caused by the kernel.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Added dma_mapping_error() API after mapping an address with dma_map_single()
API. Otherwise when CONFIG_DMA_API_DEBUG is enabled in the kernel, then it
complains about mpt3sas driver not calling dma_mapping_error after mapping an
address with dma_map_single
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Created a thread using alloc_ordered_workqueue() API in order to process
the works from firmware Work-queue sequentially instead of
create_singlethread_workqueue() API.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Joe Lawrence <joe.lawrence@stratus.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
scsi_dma_map API will return a negative value (i.e. -ENOMEM)
if DMA mapping of sg lists fails and zero if the sg list in the
SCSI cmd is NULL. But drivers doesn't handled sg list DMA mapping
failure case properly.
So, Updated the code to return host busy error status to SCSI MID Layer(SML),
when DMA mapping of scatter gather list fails for a SCSI command.
So that SML will retry this SCSI cmd after some time.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
For any SCSI command, if the driver receives
IOC status = SCSI_IOC_TERMINATED and log info = 0x32010081 then
that command will be completed with DID_RESET host status.
The definition of this log info value is
"Virtual IO has failed and has to be retried".
Firmware will provide this log info value with IOC Status
"SCSI_IOC_TERMINATED", whenever a drive (with is a part of a volume)
is pulled and pushed back within some minimal delay.
With this log info value, firmware informs the driver to retry the
failed IO command infinite times, so to provide some time for the
firmware to discover the reinserted drive successfully instated of
just retrying failed command for five times(doesn't giving enough
time for firmware to complete the drive discovery) and failing the
IO permanently even though drive came back successfully.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Below are the new changes to MPI 2.5 Rev K(2.5.6) specification and 2.00.35
header files
1) Added a minimum size requirement for target mode command buffers.
2) Added MinMSIxIndex and MaxMSIxIndex fields to CommandBufferPostBase
Request.
3) For BIOS Page 1, added SSUTimeout field, and added Product Name String
Format bits to the BiosOptions field
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Following is the change set,
1. Added more defines for the BiosOptions field of MPI2_CONFIG_PAGE_BIOS_1.
2. Added MPI2_TOOLBOX_CLEAN_BIT26_PRODUCT_SPECIFIC definition.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
This Patch will provide more details of the devices such as slot number,
enclosure logical id, enclosure level & connector name in the following
scenarios,
- When end device is added in the topology,
- When the end device is removed from the setup,
- When the SCSI mid layer issues TASK ABORT/ DEVICE RESET/ TARGET RESET during
error handling,
- When any command to the device fails with Sense key Hardware error or Medium
error or Unit Attention,
- When firmware returns device error or device not ready status for the end
device,
- When a Predicted fault is detected on an end device.
This information can be used by the user to identify the location of the
desired drive in the topology.
Driver will get these information by reading the sas device page0.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Update MPI 2.5 Release: MPI 2.5 Rev I (2.5.4) specification and 2.00.33 header
files
Below is the change set from the MPI specification for I Rev
1) Added Base Enclosure Level bit to the Flags field of Manufacturing Page 7.
2) Updated description of the MaxTargetPortConnectTime field of SAS IO Unit
Page 1.
3) Added EnclosureLevel and ConnectorName fields to SAS Device Page 0. Also,
added EnclosureLevel and ConnectorName Valid bit to the Flags field.
4) Added EnclosureLevel field to SAS Enclosure Page 0. Also, added
EnclosureLevel Valid bit to the Flags field.
5) Added value for BIOS image to HashImageType.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
During hot-plugging of a disk(having a flaky link), the disk addition
stops and any further disk addition or removal doesn't happen on that
controller.
This is because, when driver receives DELAY_NOT_RESPONDING event for a disk
while it is undergoing addition at the SCSI Transport layer, the driver
would block the I/O to that disk resulting in a deadlock. i.e the disk
addition work couldn't be completed at the SCSI Transport Layer as it
can't send any I/Os (such as Inquiry, Report LUNs etc) to the disk as
I/Os are blocked to this drive. Also any subsequent device removal
(TARGET_NOT_RESPONDING) or link update(RC_PHY_CHANGED) event couldn't be
processed as they are in the queue to get processed after disk addition
event.
Description of Change:
Don't block the drive when drive addition is under the control of SML.
So that SML won't be blocked of issuing the device dicovery commands
(such as Inquiry, Report LUNs etc).
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Driver initialization fails if driver tries to send IOC facts request message
when the IOC is in reset or in a fault state.
This patch will make sure that
1.Driver to send IOC facts request message only if HBA is in operational or
ready state.
2.If IOC is in fault state, a diagnostic reset would be issued.
3.If IOC is in reset state then driver will wait for 10 seconds to exit out
of reset state. If the HBA continues to be in reset state, then the HBA
wouldn't be claimed by the driver.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
In this patch, increased the number of MSIX vector support for SAS3 C0 HBAs to
up-to 96.
Following are changes that are done in this patch
1. This feature is enabled only for SAS3 C0 and higher revision cards and also
only when reply post free queue count is greater than 8.
2. To support this feature 12 SupplementalReplyPostHostIndex system interfaces
are used. MSI-X index numbered from 0 to 7 use the first
SupplementalReplyPostHostIndex system interface to update its corresponding
ReplyPostHostIndex values, MSI-X index numbered from 8 to 15 will use the
second SupplementalReplyPostHostIndex system interface and so on. These 12
SuppementalReplyPostHostIndex system interfaces address are saved in the array
replyPostRegisterIndex[].
3. As each SupplementalReplyPostHostIndex register supports 8 MSI-X
vectors. So MSIxIndex field in these register must contain a value between 0
and 7.
4. After processing the reply descriptors from a reply post free queues then
update the new reply post host index value in ReplyPostHostIndex field and
(msix_index mod 8) value in MSIxIndex field of SupplementalReplyPostHostIndex
register. The Address of this SupplementalReplyPostHostIndex register is
retrived from (msix_index/8)th entry of replyPostRegisterIndex[] array.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
We recently did some cleanup here and now the static checkers notice
that there is a missing error code when ioremap() fails. Let's set it
to -ENOMEM.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
In the function storvsc_channel_init(), error code was not getting
set correctly in some of the failure cases. Fix this issue.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Allow WRITE_SAME for Windows10 and above hosts.
Tested-by: Alex Ng <alexng@microsoft.com>
Signed-off-by: Keith Mange <keith.mange@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Use storage protocol version instead of vmbus protocol
version when determining storage capabilities.
Tested-by: Alex Ng <alexng@microsoft.com>
Signed-off-by: Keith Mange <keith.mange@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Use correct defaults for values determined by protocol negotiation,
instead of resetting them with every scsi controller.
Tested-by: Alex Ng <alexng@microsoft.com>
Signed-off-by: Keith Mange <keith.mange@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Currently we are making decisions based on vmbus protocol versions
that have been negotiated; use storage potocol versions instead.
[jejb: fold ARRAY_SIZE conversion suggested by Johannes Thumshirn
<jthumshirn@suse.de>
make vmstor_protocol static]
Tested-by: Alex Ng <alexng@microsoft.com>
Signed-off-by: Keith Mange <keith.mange@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Use a single value to track protocol versions to simplify
comparisons and to be consistent with vmbus version tracking.
Tested-by: Alex Ng <alexng@microsoft.com>
Signed-off-by: Keith Mange <keith.mange@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Rather than look for sets of specific protocol versions,
make decisions based on ranges. This will be safer and require fewer changes
going forward as we add more storage protocol versions.
Tested-by: Alex Ng <alexng@microsoft.com>
Signed-off-by: Keith Mange <keith.mange@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
The queuecommand routine has a local dev pointer used for the
dev_* prints. The two prints that currently exist are tucked
under a debug define and thus can be left out. Use the actual
location instead of a local to avoid this warning.
This patch is intended to be applied after the "CXL Flash Error
Recovery and Superpipe" series.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
"port_sel" is a u64 so the shifting should also be a 64 bit shift.
Fixes: c21e0bbfc4 ('cxlflash: Base support for IBM CXL Flash Adapter')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
The > should be >= or we read one element past the end of the array.
Fixes: c21e0bbfc4 ('cxlflash: Base support for IBM CXL Flash Adapter')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Add support for physical LUN segmentation (virtual LUNs) to device
driver supporting the IBM CXL Flash adapter. This patch allows user
space applications to virtually segment a physical LUN into N virtual
LUNs, taking advantage of the translation features provided by this
adapter.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Reviewed-by: Michael Neuling <mikey@neuling.org>
Reviewed-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Add superpipe supporting infrastructure to device driver for the IBM CXL
Flash adapter. This patch allows userspace applications to take advantage
of the accelerated I/O features that this adapter provides and bypass the
traditional filesystem stack.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Reviewed-by: Michael Neuling <mikey@neuling.org>
Reviewed-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Introduce support for enhanced I/O error handling.
A device state is added to track 3 possible states of the device:
Normal - the device is operating normally and is fully operational
Limbo - the device is in a reset/recovery scenario and its operational
status is paused
Failed/terminating - the device has either failed to be reset/recovered
or is being terminated (removed); it is no longer
operational
All operations are allowed when the device is operating normally. When the
device transitions to limbo state, I/O must be paused. To help accomplish
this, a wait queue is introduced where existing and new threads can wait
until the device is no longer in limbo. When coming out of limbo, threads
need to check the state and error out gracefully when encountering the
failed state. When the device transitions to the failed/terminating state,
normal operations are no longer allowed. Only specially designated
operations related to graceful cleanup are permitted.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Reviewed-by: Daniel Axtens <dja@axtens.net>
Reviewed-by: Michael Neuling <mikey@neuling.org>
Reviewed-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
On certain conditions, login failures will just invoke
qla2x00_mark_device_lost() with the intend to do login again;
but if login_retry has been set already, that would fail to set the
relogin needed flag which is required to wakeup the DPC to retry.
Signed-off-by: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Fix for memory leak when command is not found by firmware due to
mismatch in sp reference count.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Instead of resetting the adapter wait for the login to timeout
and retry. Resetting the adapter can cause extended path recovery
times.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
If an SRB is NULL but the handle is in range just drop the
command instead of also resetting the adapter. If the handle
is in range then the command was valid at some point and may
have been aborted. Resetting the adapter can lead to extended
recovery times in this case.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Aovid crashing the system in the scenario where firmware
just completes the command and it can not find the command
during abort mailbox processing. This scenario can lead to
sp reference counter being zero. Instead of crashing the
system, use WARN_ON to print warning in log file.
Signed-off-by: Hiral Patel <hiral.patel@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Execute qla25xx_manipulate_risc_semaphore() only for
ssdid 0x0175 and 0x0240.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
When we get logged out, mark the port lost and set dpc flag for relogin.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Hannes Reinecke
Gabriel Krisman Bertazi
Sreekanth Reddy
Dan Carpenter
K. Y. Srinivasan
Keith Mange
Matthew R. Ochs
Himanshu Madhani
Sawan Chandak
Arun Easi
Chad Dupuis
Hiral Patel
Saurav Kashyap
Joe Carnuccio