When we are waiting for the bit-lock to be released, and are looping
over the 'cpu_relax()' should not be doing anything else - otherwise we
miss the point of trying to do the whole 'cpu_relax()'.
Do the preemption enable/disable around the loop, rather than inside of
it.
Noticed when I was looking at the code generation for the dcache
__d_drop usage, and the code just looked very odd.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: ahci_start_engine compliant to AHCI spec
ata: pata_at91.c bugfix for initial_timing initialisation
ata: pata_at91.c bugfix for high master clock
ahci: AHCI-mode SATA patch for Intel Panther Point DeviceIDs
ata_piix: IDE-mode SATA patch for Intel Panther Point DeviceIDs
libata: Pioneer DVR-216D can't do SETXFER
ahci: don't enable port irq before handler is registered
libata: Implement ATA_FLAG_NO_DIPM and apply it to mcp65
libata: Kill unused ATA_DFLAG_{H|D}IPM flags
ahci: EM supported message type sysfs attribute
* 'for-linus' of git://git.infradead.org/ubifs-2.6:
UBIFS: fix master node recovery
UBIFS: fix false assertion warning in case of I/O failures
UBIFS: fix false space checking failure
At the end of section 10.1 of AHCI spec (rev 1.3), it states
Software shall not set PxCMD.ST to 1 until it is determined that
a functoinal device is present on the port as determined by
PxTFD.STS.BSY=0, PxTFD.STS.DRQ=0 and PxSSTS.DET=3h
Even though most AHCI host controller works without this check,
specific controller will fail under this condition.
Signed-off-by: Jian Peng <jipeng2005@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The "struct ata_timing" must contain 10 members, but ".dmack_hold" member was
forgotten for "initial_timing" initialisation. This patch fixes such a problem.
Signed-off-by: Igor Plyatov <plyatov@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The AT91SAM9 microcontrollers with master clock higher then 105 MHz
and PIO0, have overflow of the NCS_RD_PULSE value in the MSB. This
lead to "NCS_RD_PULSE" pulse longer then "NRD_CYCLE" pulse and driver
does not detect ATA device.
Signed-off-by: Igor Plyatov <plyatov@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The previously submitted patch was word-wrapped.
This patch adds the AHCI-mode SATA DeviceIDs for the Intel Panther Point PCH.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The previously submitted patch was word-wrapped.
This patch adds the IDE-mode SATA DeviceIDs for the Intel Panther
Point PCH.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Commit 4a5610a04d fixed an issue with
the Pioneer DVR-212D not handling SETXFER correctly. An openSUSE user
reported a similar issue with his DVR-216D that the NOSETXFER horkage
worked around for him as well.
This patch adds the DVR-216D (1.08) to the horkage list for NOSETXFER.
The issue was reported at:
https://bugzilla.novell.com/show_bug.cgi?id=679143
Reported-by: Volodymyr Kyrychenko <vladimir.kirichenko@gmail.com>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The ahci_pmp_attach() & ahci_pmp_detach() unmask port irqs, but they
are also called during port initialization, before ahci host irq
handler is registered. On ce4100 platform, this sometimes triggers
"irq 4: nobody cared" message when loading driver.
Fixed this by not touching the register if the port is in frozen
state, and mark all uninitialized port as frozen.
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
NVIDIA mcp65 familiy of controllers cause command timeouts when DIPM
is used. Implement ATA_FLAG_NO_DIPM and apply it.
This problem was reported by Stefan Bader in the following thread.
http://thread.gmane.org/gmane.linux.ide/48841
stable: applicable to 2.6.37 and 38.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Stefan Bader <stefan.bader@canonical.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch adds an sysfs attribute 'em_message_supported' to the
ahci host device which prints out the supported enclosure management
message types.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Commit 40aee729b3 ('kconfig: fix default value for choice input')
fixed some cases where kconfig would select the wrong option from a
choice with a single valid option and thus enter an infinite loop.
However, this broke the test for user input of the form 'N?', because
when kconfig selects the single valid option the input is zero-length
and the test will read the byte before the input buffer. If this
happens to contain '?' (as it will in a mips build on Debian unstable
today) then kconfig again enters an infinite loop.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: stable@kernel.org [2.6.17+]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The dentry hashing rules have been really quite complicated for a long
while, in odd ways. That made functions like __d_drop() very fragile
and non-obvious.
In particular, whether a dentry was hashed or not was indicated with an
explicit DCACHE_UNHASHED bit. That's despite the fact that the hash
abstraction that the dentries use actually have a 'is this entry hashed
or not' model (which is a simple test of the 'pprev' pointer).
The reason that was done is because we used the normal 'is this entry
unhashed' model to mark whether the dentry had _ever_ been hashed in the
dentry hash tables, and that logic goes back many years (commit
b3423415fb: "dcache: avoid RCU for never-hashed dentries").
That, in turn, meant that __d_drop had totally different unhashing logic
for the dentry hash table case and for the anonymous dcache case,
because in order to use the "is this dentry hashed" logic as a flag for
whether it had ever been on the RCU hash table, we had to unhash such a
dentry differently so that we'd never think that it wasn't 'unhashed'
and wouldn't be free'd correctly.
That's just insane. It made the logic really hard to follow, when there
were two different kinds of "unhashed" states, and one of them (the one
that used "list_bl_unhashed()") really had nothing at all to do with
being unhashed per se, but with a very subtle lifetime rule instead.
So turn all of it around, and make it logical.
Instead of having a DENTRY_UNHASHED bit in d_flags to indicate whether
the dentry is on the hash chains or not, use the hash chain unhashed
logic for that. Suddenly "d_unhashed()" just uses "list_bl_unhashed()",
and everything makes sense.
And for the lifetime rule, just use an explicit DENTRY_RCUACCEES bit.
If we ever insert the dentry into the dentry hash table so that it is
visible to RCU lookup, we mark it DENTRY_RCUACCESS to show that it now
needs the RCU lifetime rules. Now suddently that test at dentry free
time makes sense too.
And because unhashing now is sane and doesn't depend on where the dentry
got unhashed from (because the dentry hash chain details doesn't have
some subtle side effects), we can re-unify the __d_drop() logic and use
common code for the unhashing.
Also fix one more open-coded hash chain bit_spin_lock() that I missed in
the previous chain locking cleanup commit.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It's a useless abstraction for 'hlist_bl_head', and it doesn't actually
help anything - quite the reverse. All the users end up having to know
about the hlist_bl_head details anyway, using 'struct hlist_bl_node *'
etc. So it just makes the code look confusing.
And the cost of it is extra '&b->head' syntactic noise, but more
importantly it spuriously makes the hash table dentry list look
different from the per-superblock DCACHE_DISCONNECTED dentry list.
As a result, the code ended up using ad-hoc locking for one case and
special helper functions for what is really another totally identical
case in the very same function.
Make it all look and work the same.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
tty/n_gsm: fix bug in CRC calculation for gsm1 mode
serial/imx: read cts state only after acking cts change irq
parport_pc.c: correctly release the requested region for the IT887x
Right now all RCU walks fall back to reference walk when CONFIG_SECURITY
is enabled, even though just the standard capability module is active.
This is because security_inode_exec_permission unconditionally fails
RCU walks.
Move this decision to the low level security module. This requires
passing the RCU flags down the security hook. This way at least
the capability module and a few easy cases in selinux/smack work
with RCU walks with CONFIG_SECURITY=y
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda - Fix unused warnings when !SND_HDA_NEEDS_RESUME
ALSA: hda - Add a fix-up for Acer dmic with ALC271x codec
ASoC: add a module alias to the FSI driver
ALSA: emu10k1 - Fix "Music" controls to "Synth" controls in documents
ARM: s3c2440: gta02; Register dfbmcs320 device for BT audio interface
ASoC: codecs: JZ4740: Fix OOPS
ASoC: Fix output PGA enabling in wm_hubs CODECs
ASoC: sn95031: decorate function with __devexit_p()
ASoC: SAMSUNG: Fix the inverted clocks handling for pcm driver
ASoC: sst_platform: Fix lock acquring
ASoC: fsi: driver safely remove for against irq
ASoC: fsi: modify vague PM control on probe
ASoC: fsi: take care in failing case of dai register
MAINTAINERS: Update Samsung ASoC maintainer's id
ASoC: WM8903: HP and Line out PGA/mixer DAPM fixes
ASoC: Set left channel volume update bits for WM8994
ASoC: fix config error path
ASoC: check channel mismatch between cpu_dai and codec_dai
ASoC: Tegra: Suspend/resume support
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf, x86: Update/fix Intel Nehalem cache events
perf, x86: P4 PMU - Don't forget to clear cpuc->active_mask on overflow
x86, perf event: Turn off unstructured raw event access to offcore registers
perf: Support Xeon E7's via the Westmere PMU driver
It's not enough to simply disable event on overflow the
cpuc->active_mask should be cleared as well otherwise counter
may stall in "active" even in real being already disabled (which
potentially may lead to the situation that user may not use this
counter further).
Don pointed out that:
" I also noticed this patch fixed some unknown NMIs
on a P4 when I stressed the box".
Tested-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Acked-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Don Zickus <dzickus@redhat.com>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Link: http://lkml.kernel.org/r/1303398203-2918-3-git-send-email-dzickus@redhat.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Andi Kleen pointed out that the Intel offcore support patches were merged
without user-space tool support to the functionality:
|
| The offcore_msr perf kernel code was merged into 2.6.39-rc*, but the
| user space bits were not. This made it impossible to set the extra mask
| and actually do the OFFCORE profiling
|
Andi submitted a preliminary patch for user-space support, as an
extension to perf's raw event syntax:
|
| Some raw events -- like the Intel OFFCORE events -- support additional
| parameters. These can be appended after a ':'.
|
| For example on a multi socket Intel Nehalem:
|
| perf stat -e r1b7:20ff -a sleep 1
|
| Profile the OFFCORE_RESPONSE.ANY_REQUEST with event mask REMOTE_DRAM_0
| that measures any access to DRAM on another socket.
|
But this kind of usability is absolutely unacceptable - users should not
be expected to type in magic, CPU and model specific incantations to get
access to useful hardware functionality.
The proper solution is to expose useful offcore functionality via
generalized events - that way users do not have to care which specific
CPU model they are using, they can use the conceptual event and not some
model specific quirky hexa number.
We already have such generalization in place for CPU cache events,
and it's all very extensible.
"Offcore" events measure general DRAM access patters along various
parameters. They are particularly useful in NUMA systems.
We want to support them via generalized DRAM events: either as the
fourth level of cache (after the last-level cache), or as a separate
generalization category.
That way user-space support would be very obvious, memory access
profiling could be done via self-explanatory commands like:
perf record -e dram ./myapp
perf record -e dram-remote ./myapp
... to measure DRAM accesses or more expensive cross-node NUMA DRAM
accesses.
These generalized events would work on all CPUs and architectures that
have comparable PMU features.
( Note, these are just examples: actual implementation could have more
sophistication and more parameter - as long as they center around
similarly simple usecases. )
Now we do not want to revert *all* of the current offcore bits, as they
are still somewhat useful for generic last-level-cache events, implemented
in this commit:
e994d7d23a: perf: Fix LLC-* events on Intel Nehalem/Westmere
But we definitely do not yet want to expose the unstructured raw events
to user-space, until better generalization and usability is implemented
for these hardware event features.
( Note: after generalization has been implemented raw offcore events can be
supported as well: there can always be an odd event that is marginally
useful but not useful enough to generalize. DRAM profiling is definitely
*not* such a category so generalization must be done first. )
Furthermore, PERF_TYPE_RAW access to these registers was not intended
to go upstream without proper support - it was a side-effect of the above
e994d7d23a commit, not mentioned in the changelog.
As v2.6.39 is nearing release we go for the simplest approach: disable
the PERF_TYPE_RAW offcore hack for now, before it escapes into a released
kernel and becomes an ABI.
Once proper structure is implemented for these hardware events and users
are offered usable solutions we can revisit this issue.
Reported-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1302658203-4239-1-git-send-email-andi@firstfloor.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
ide: unexport DISK_EVENT_MEDIA_CHANGE for ide-gd and ide-cd
block: don't propagate unlisted DISK_EVENTs to userland
elevator: check for ELEVATOR_INSERT_SORT_MERGE in !elvpriv case too
check_events() implementations in both ide-gd and ide-cd are
inadequate for in-kernel event polling. Both generate media change
events continuously when certain conditions are met causing infinite
event loop between the driver and userland event handler.
As disk event now supports suppression of unlisted events, simply
de-listing DISK_EVENT_MEDIA_CHANGE from disk->events resolves the
problem. Internal handling around media revalidation will behave the
same while userland will fall back to userland event polling after
detecting the device doesn't support disk events.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Jens Axboe <jaxboe@fusionio.com>
Acked-by: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
DISK_EVENT_MEDIA_CHANGE is used for both userland visible event and
internal event for revalidation of removeable devices. Some legacy
drivers don't implement proper event detection and continuously
generate events under certain circumstances. For example, ide-cd
generates media changed continuously if there's no media in the drive,
which can lead to infinite loop of events jumping back and forth
between the driver and userland event handler.
This patch updates disk event infrastructure such that it never
propagates events not listed in disk->events to userland. Those
events are processed the same for internal purposes but uevent
generation is suppressed.
This also ensures that userland only gets events which are advertised
in the @events sysfs node lowering risk of confusion.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
The sort insert is the one that goes to the IO scheduler. With
the SORT_MERGE addition, we could bypass IO scheduler setup
but still ask the IO scheduler to insert the request. This would
cause an oops on switching IO schedulers through the sysfs
interface, unless the disk just happened to be idle while it
occured.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, numa: Fix cpu nodemasks for NUMA emulation and CONFIG_DEBUG_PER_CPU_MAPS
Revert "x86, NUMA: Fix fakenuma boot failure"
Change <sectors> from unsigned long long to sector_t.
This matches its source field.
ERROR: "__udivdi3" [drivers/md/raid456.ko] undefined!
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
virtio: console: Enable call to hvc_remove() on console port remove
virtio_pci: Prevent double-free of pci regions after device hot-unplug
virtio: Decrement avail idx on buffer detach
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
agp: fix arbitrary kernel memory writes
agp: fix OOM and buffer overflow
drm/radeon/kms: fix IH writeback on r6xx+ on big endian machines
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/keithp/linux-2.6:
drm/i915: Initialise g4x watermarks for disabled pipes
drm/i915: Sanitize the output registers after resume
drm/i915/tv: Fix modeset flickering introduced in 7f58aabc3
drm/i915/tv: Only poll for TV connections
drm/i915/tv: Remember the detected TV type
* git://git.infradead.org/iommu-2.6:
intel_iommu: disable all VT-d PMRs when TXT launched
intel-iommu: Fix get_domain_for_dev() error path
intel-iommu: Unlink domain from iommu
intel-iommu: Fix use after release during device attach
For some reason generic_setxattr() did not pass flags (XATTR_CREATE,
XATTR_REPLACE) to the filesystem specific helper. This caused that
setxattr(2) syscall just ignored these flags.
Fix the bug by passing flags correctly.
Signed-off-by: Jan Kara <jack@suse.cz>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This call was disabled as hot-unplugging one virtconsole port led to
another virtconsole port freezing.
Upon testing it again, this now works, so enable it.
In addition, a bug was found in qemu wherein removing a port of one type
caused the guest output from another port to stop working. I doubt it
was just this bug that caused it (since disabling the hvc_remove() call
did allow other ports to continue working), but since it's all solved
now, we're fine with hot-unplugging of virtconsole ports.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
In the case where a virtio-console port is in use (opened by a program)
and a virtio-console device is removed, the port is kept around but all
the virtio-related state is assumed to be gone.
When the port is finally released (close() called), we call
device_destroy() on the port's device. This results in the parent
device's structures to be freed as well. This includes the PCI regions
for the virtio-console PCI device.
Once this is done, however, virtio_pci_release_dev() kicks in, as the
last ref to the virtio device is now gone, and attempts to do
pci_iounmap(pci_dev, vp_dev->ioaddr);
pci_release_regions(pci_dev);
pci_disable_device(pci_dev);
which results in a double-free warning.
Move the code that releases regions, etc., to the virtio_pci_remove()
function, and all that's now left in release_dev is the final freeing of
the vp_dev.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
When detaching a buffer from a vq, the avail.idx value should be
decremented as well.
This was noticed by hot-unplugging a virtio console port and then
plugging in a new one on the same number (re-using the vqs which were
just 'disowned'). qemu reported
'Guest moved used index from 0 to 256'
when any IO was attempted on the new port.
CC: stable@kernel.org
Reported-by: juzhang <juzhang@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Intel VT-d Protected Memory Regions (PMRs) are supposed to be disabled,
on each VT-d engine, after DMA remapping is enabled on the engines.
This is because the behavior of having both enabled is not deterministic
and because, if TXT has been used to launch the kernel, the PMRs may be
programmed to cover memory regions that will be used for DMA.
Under some circumstances (certain quirks detected, lack of multiple
devices, etc.), the current code does not set up DMA remapping on some
VT-d engines. In such cases it also skips disabling the PMRs. This
causes failures when the kernel is launched with TXT (most often this
occurs on the graphics engine and results in colored vertical bars on
the display).
This patch detects when the kernel has been launched with TXT and then
disables the PMRs on all VT-d engines. In some cases where the reason
that remapping is not being enabled is due to possible ACPI DMAR table
errors, the VT-d engine addresses may not be correct and thus not able
to be safely programmed even to disable PMRs. Because part of the TXT
launch process is the verification of these addresses, it will always be
safe to disable PMRs if the TXT launch has succeeded and hence only
doing this in such cases.
Signed-off-by: Joseph Cihula <joseph.cihula@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch fixes the following symptoms:
1. Unmount UBIFS cleanly.
2. Start mounting UBIFS R/W and have a power cut immediately
3. Start mounting UBIFS R/O, this succeeds
4. Try to re-mount UBIFS R/W - this fails immediately or later on,
because UBIFS will write the master node to the flash area
which has been written before.
The analysis of the problem:
1. UBIFS is unmounted cleanly, both copies of the master node are clean.
2. UBIFS is being mounter R/W, starts changing master node copy 1, and
a power cut happens. The copy N1 becomes corrupted.
3. UBIFS is being mounted R/O. It notices the copy N1 is corrupted and
reads copy N2. Copy N2 is clean.
4. Because of R/O mode, UBIFS cannot recover copy 1.
5. The mount code (ubifs_mount()) sees that the master node is clean,
so it decides that no recovery is needed.
6. We are re-mounting R/W. UBIFS believes no recovery is needed and
starts updating the master node, but copy N1 is still corrupted
and was not recovered!
Fix this problem by marking the master node as dirty every time we
recover it and we are in R/O mode. This forces further recovery and
the UBIFS cleans-up the corruptions and recovers the copy N1 when
re-mounting R/W later.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Cc: stable@kernel.org
When UBIFS switches to R/O mode because it detects I/O failures, then
when we unmount, we still may have allocated budget, and the assertions
which verify that we have not budget will fire. But it is expected to
have the budget in case of I/O failures, so the assertion warnings will
be false. Suppress them for the I/O failure case.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
The cpu<->node mappings under CONFIG_DEBUG_PER_CPU_MAPS=y
when NUMA emulation is enabled is currently broken because it does
not iterate through every emulated node and bind cpus that have
affinity to it.
NUMA emulation should bind each cpu to every local node to
accurately represent the true NUMA topology of the underlying
machine.
debug_cpumask_set_cpu() needs to be fixed at the same time so
that the debugging information that it emits shows the new
cpumask of the node being assigned when the cpu is being added
or removed.
It can now take responsibility of setting or clearing the cpu
itself to remove the need for duplicate code.
Also change its last parameter, "enable", to have the correct bool
type since it can only be true or false.
-v2: Fix the return statements, by Kosaki Motohiro
Acked-and-Tested-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Andreas Herrmann <herrmann.der.user@googlemail.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/alpine.DEB.2.00.1104201918470.12634@chino.kir.corp.google.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Andreas Herrmann reported that 7d6b46707f ("x86, NUMA: Fix fakenuma
boot failure") causes certain physical NUMA topologies (for example
AMD Magny-Cours) to move sibling cpus to a single node when in reality
they are in separate domains.
This may result in some nodes being completely void of cpus, which
doesn't accurately represent the correct topology. The system will
boot, but will have suboptimal NUMA performance.
This commit was intended as a fix for NUMA emulation, but should
not cause a regression for real NUMA machines as a side effect.
( There will be a separate fix for the numa-debug code, which
will not affect physical topologies. )
Reported-by: Andreas Herrmann <herrmann.der.user@googlemail.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/alpine.DEB.2.00.1104201918110.12634@chino.kir.corp.google.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
pg_start is copied from userspace on AGPIOC_BIND and AGPIOC_UNBIND ioctl
cmds of agp_ioctl() and passed to agpioc_bind_wrap(). As said in the
comment, (pg_start + mem->page_count) may wrap in case of AGPIOC_BIND,
and it is not checked at all in case of AGPIOC_UNBIND. As a result, user
with sufficient privileges (usually "video" group) may generate either
local DoS or privilege escalation.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
page_count is copied from userspace. agp_allocate_memory() tries to
check whether this number is too big, but doesn't take into account the
wrap case. Also agp_create_user_memory() doesn't check whether
alloc_size is calculated from num_agp_pages variable without overflow.
This may lead to allocation of too small buffer with following buffer
overflow.
Another problem in agp code is not addressed in the patch - kernel memory
exhaustion (AGPIOC_RESERVE and AGPIOC_ALLOCATE ioctls). It is not checked
whether requested pid is a pid of the caller (no check in agpioc_reserve_wrap()).
Each allocation is limited to 16KB, though, there is no per-process limit.
This might lead to OOM situation, which is not even solved in case of the
caller death by OOM killer - the memory is allocated for another (faked) process.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
