Add necessary barriers after enabling MMU. Also use the sane way to
load pc and jump to it instead of executing ldma first up.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
On ARMv7 dsb, dmb instructions are supported and can be used directly
instead of their cp15 equivalnet. Also remove the opcodes for smc
and use the available instruction directly in OMAP3 low power asm code
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
When we're interrupted on the secure side, we should just issue
another smc instruction again instead of replaying the arguments
to smc. Fix it.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Assign the registers used in the inline assembly immediately
before the inline assembly block. This ensures the compiler
doesn't optimize away dead register assignments when it
shouldn't.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: David Brown <davidb@codeaurora.org>
We don't want the compiler to remove these asm statements or
reorder them in any way. Mark them as volatile to be sure.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: David Brown <davidb@codeaurora.org>
There should be no reason to call h4_init_flash this
early. It causes problems as things are not yet initialized.
Tested-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Various binutils versions can resolve Thumb-2 branches to
locally-defined, preemptible global symbols as short-range "b.n"
branch instructions.
This is a problem, because there's no guarantee the final
destination of the symbol, or any candidate locations for a
trampoline, are within range of the branch. For this reason, the
kernel does not support fixing up the R_ARM_THM_JUMP11 (102)
relocation in modules at all, and it makes little sense to add
support.
The symptom is that the kernel fails with an "unsupported
relocation" error when loading some modules.
Until fixed tools are available, passing
-fno-optimize-sibling-calls to gcc should prevent gcc generating
code which hits this problem, at the cost of a bit of extra runtime
stack usage in some cases.
The problem is described in more detail at:
https://bugs.launchpad.net/binutils-linaro/+bug/725126
Only Thumb-2 kernels are affected.
This patch adds a new CONFIG_THUMB2_AVOID_R_ARM_THM_JUMP11 config
option which adds -fno-optimize-sibling-calls to CFLAGS_MODULE
when building a Thumb-2 kernel.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Adding Thumb2 support to the runtime patching of the virt_to_phys and
phys_to_virt opcodes.
Tested both the 8-bit and the 16-bit fixups, using different placements
in memory to exercize all code paths.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Reviewed-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The removal of the single-step emulation from ptrace on ARM means that
thread_struct no longer has software breakpoint fields in its debug
member.
This patch fixes the a.out core dump code so that the debug registers
are zeroed rather than trying to copy from non-existent fields.
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some cards have the CRC errors in read on mx51 BBG board.
Configure the eSDHC pad configurations to level up the
compatibility to fix this issue.
Signed-off-by: Richard Zhu <Hong-Xing.Zhu@freescale.com>
Tested-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This saves some power. OMAP4 version should check for GPT module ID, as
autoidle is only supported on a subset of these.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add a new clockdomain flag, CLKDM_NO_AUTODEPS, which, when marked on a
clockdomain, will prevent "autodeps" from being associated with the
clockdomain. ("Autodeps" are sleep dependencies and wakeup
dependencies from/to processor modules that are automatically added to
a clockdomain when it is in hardware-supervised idle mode. They are
deprecated -- a relic from the old CDP trees -- but are still in use
for OMAP3.)
Also, prevent the hwmod code from adding or removing initiator
dependencies for clockdomains with this flag set.
This patch should allow others to test which clockdomains actually
still need autodeps.
Thanks to Kevin Hilman <khilman@ti.com> for noting that the original
version should also modify the hwmod code.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Create a new API that forms a wrapper to _set_module_autoidle()
to modify the AUTOIDLE bit.
This API is intended to be used by drivers that requires direct
manipulation of the AUTOIDLE bits in SYSCONFIG register.
McBSP driver requires autoidle bit to be enabled/disabled while
using sidetone feature.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
[paul@pwsan.com: restrict the hwmod states that the autoidle bit can be changed
in; changed function name; dropped "int" from "unsigned int long"]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some boards can't tolerate IP blocks being reset when they are initialized.
Michael Büsch cites a case with the Nokia N810:
http://www.spinics.net/lists/linux-omap/msg47277.html
To allow such boards to continue working normally, allow board file
maintainers to mark IP blocks to prevent them from being reset upon
init. This is done via a hwmod function, omap_hwmod_no_setup_reset().
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Michael Buesch <mb@bu3sch.de>
On OMAP2 and OMAP3 the reset ctrl shift doesn't match the
status bit, as it does on OMAP4, when handling the reset lines.
This patch adds a new member in the reset info structure, so now it
can be added as part of hwmod data, and checked accordingly for
OMAP2 or 3; otherwise, there could be cases when the shift masks
doesn't match both of the registers, and a successful reset might
throw an error message or vice versa.
Signed-off-by: Omar Ramirez Luna <omar.ramirez@ti.com>
[paul@pwsan.com: added a warning if st_shift used on OMAP4; renamed 'r'
variable; improved some documentation]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
_init_clock always returns 0 and does
not propogate the error (in case of failure)
back to the caller, causing _init_clocks to
fail silently.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some of the omap2, omap3 peripherals support software reset. This
can be done through the softreset bit in sysconfig register.
The reset status can be checked through resetdone bit of
sysstatus register. syss_has_reset_status is added to the hwmod
database of peripherals which have resetdone bit in sysstatus register.
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Reviewed-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Avinash.H.M <avinashhm@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Autoidle is a single bit, TIOCP_CFG[0], setting on OMAP1/2/3/4 platforms.
In _set_module_autoidle() I am seeing 0x3 value where the mask is computed.
This should be 0x1.
v2:
(1) Modified the subject.
(2) Modified the description with further specific information.
Baseline:
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6.git
Tested Info:
Boot tested on OMAP 1/2/3/4.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Acked-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Master ports from interconnect are generating some annoying circular
references that become tricky to handle if we have to dynamically
remove some IP on some variant platforms.
Since they are not used for the moment, and since we can still build
that relation using the reverse relation (slave port from the IP
toward master port of the interconnect), let remove them for the
moment like it is done on OMAP4.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Sanjeev Premi <premi@ti.com>
Most likely, the LCD panel on mx28 platform will require a pixel
clock higher than ref_xtal_clk (24 MHz), so the patch initializes
the parent of lcdif clock as ref_pix_clk.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Use the correct I/O address definitions for Footbridge
peripherals when the kernel is compiled without MMU
support.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit d344272671 ("OMAP3: PM: Adding
smartreflex hwmod data") added data that claims that the L4 CORE has
two slave interfaces that originate from the SmartReflex modules,
omap3_l4_core__sr1 and omap3_l4_core__sr2. But as those two data
structure records show, it's L4 CORE that has a master port towards
SR1 and SR2.
Move the incorrect data from slaves list to master list.
Based on a path by Paul Walmsley <paul@pwsan.com>
https://patchwork.kernel.org/patch/623171/
That is based on a patch by Benoît Cousson <b-cousson@ti.com>:
https://patchwork.kernel.org/patch/590561/
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Cc: Sanjeev Premi <premi@ti.com>
Cc: Thara Gopinath <thara@ti.com>
if building kernels without OMAP2 support, we
will see a warning such as:
arch/arm/mach-omap2/io.c: In function 'omap2_init_common_infrastructure':
arch/arm/mach-omap2/io.c:389:3: warning: statement with no effect
arch/arm/mach-omap2/io.c:391:3: warning: statement with no effect
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
omap_sr_probe() creates the smartreflex debug directory and its
underlying nvalue debug directory. These directories are removed in
omap_sr_remove().
Basic smartreflex functionality tested on OMAP3630 Zoom3 & OMAP4430 SDP
Signed-off-by: Anand S Sawant <sawant@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
* Build unconditionally as ARM for correct interoperation with
OMAP firmware.
* Fix an out-of-range ADR when building for ARM.
* Remove deprecated PC-relative stores.
* Add the required ENDPROC() directive for each ENTRY().
* .align before data words.
* Handle non-interworking return from v7_flush_dcache_all.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Kevin Hilman <khilman@ti.com>
* Build unconditionally as ARM for correct interoperation with
OMAP firmware.
* Remove deprecated PC-relative stores
* Add the required ENDPROC() directive for each ENTRY().
* .align before data words
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Tested-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
For various reasons, Linux now only officially supports being built
with tools which are new enough to understand the SMC instruction.
Replacing the hand-encoded instructions when the mnemonic also
allows for correct assembly in Thumb-2 (otherwise, the result is
random data in the middle of the code).
The Makefile already ensures that this file is built with a high
enough gcc -march= flag (armv7-a).
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Code marked with ENTRY() also needs a matching ENDPROC() directive,
in order to ensure that the type and instruction set of the
symbol are correctly annotated.
ENDPROC() tags the affected symbol as a function symbol, which will
ensure that link-time fixups don't accidentally switch to the
wrong instruction set.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
For CONFIG_THUMB2_KERNEL, the existing definition of do_wfi() will
insert invalid code into the instruction stream.
Any assembler which can assemble Thumb-2 is guaranteed to accept
the "wfi" mnemonic, so for the Thumb-2 case, just use the mnemonic.
The ARM case is left as-is.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Kevin Hilman <khilman@ti.com>
IVA device is not present in many OMAP3 variants.
This patch ensures that initialization is tied to
the presence of IVA on the device.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Voltage control on TWL can be done using VMODE/I2C1/I2C_SR.
Since almost all platforms use I2C_SR on omap3, omap3_twl_init by
default expects that OMAP's I2C_SR is plugged in to TWL's I2C
and calls omap3_twl_set_sr_bit. On platforms where I2C_SR is not connected,
the board files are expected to call omap3_twl_set_sr_bit(false) to
ensure that I2C_SR path is not set for voltage control and prevent
the default behavior of omap3_twl_init.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Shweta Gulati <shweta.gulati@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Kevin Hilman <khilman@ti.com>
Add a description field to each idle C-state. This helps to give
better data with PowerTop and one don't have to refer to the code
to link what Cx means from system point of view while analysing
PowerTop data.
No functional change.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Remove the custom restore_control_register() and use the exported
set_cr() instead to set the system control register(SCTRL) value.
No functional change.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The OMAP2 and OMAP3 PM code clears clockdomain wakeup and sleep
dependencies. This is unnecessary after commit
6f7f63cc9a ("OMAP clockdomain:
initialize clockdomain registers when the clockdomain layer starts")
which clears these dependencies during clockdomain init.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Now that omap_hwmod + omap_device is used for OMAP UART device and
driver code, we no longer need the UART physical addresses in
omap_globals.
Note that the #defines for the base addresses are still left in
<plat/serial.h> since they are used by DEBUG_LL and uncompress code.
Build tested for OMAP1 (omap1_defconfig) and OMAP2+ (omap2plus_defconfig)
Signed-off-by: Kevin Hilman <khilman@ti.com>
kzalloc() may fail, if so return -ENOMEM. Also Walter Harms suggested
to use kasprintf() instead of kzalloc+strcpy+strcat.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
OMP3630 silicon can enable higher frequencies only depending on the board
characteristics meeting the recommended standards, and has to be selectively
toggled.
Beagle XM uses 3730 variant and the board design allows enabling 800MHz and
1GHz OPPs. However, We need Smart reflex class 1.5 and ABB to enable 1GHz
safely. For the moment, we tweak the default table to allow for 800Mhz OPP
usage.
Reported-by: Koen Kooi <koen@beagleboard.org>
Tested-by: Koen Kooi <koen@beagleboard.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
omap3 and omap4 opp_init should be made non-static to allow
for platform specific opp table tweaking. making these static
conflicts with the definition in pm.h(global) as well.
we include pm.h as well to ensure that there are no such prototype
conflicts with actual implementation in the future.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
In case in user has a OMAP3630 < ES1.2 the kernel should warn the user
about the ERRATUM, but using pr_warn instead of WARN_ON is already
enough, as there is nothing else the user can do besides changing the
board.
Signed-off-by: Ricardo Salveti de Araujo <ricardo.salveti@canonical.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
On revisions of the Cortex-A9 prior to r2p0, the Store Buffer does not
have any automatic draining mechanism and therefore a livelock may occur
if an external agent continuously polls a memory location waiting to
observe an update.
This workaround defines cpu_relax() as smp_mb(), preventing correctly
written polling loops from denying visibility of updates to memory.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On the r2p* and r3p* versions of the Cortex-A9, a speculative memory
access may cause a page table walk which starts prior to an ASID switch
but completes afterwards. This can populate the micro-TLB with a stale
entry which may be hit with the new ASID.
This workaround places two dsb instructions in the mm switching code so
that no page table walks can cross the ASID switch.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This applies errata fix 753970 for all ux500 platforms. All
current ASICs suffer from this. If the problem is resolved in
later ASICs, the errata selection can be pushed down to other
Kconfig options.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
According to the hwmod interface data, the DSS submodule "VENC" uses a
clock, "dss_54m_fck"/"dss_tv_fck", which the PRCM cannot autoidle. By
default, the hwmod code assumes that interface clocks can be autoidled
by the PRCM. When the interface clock can't be autoidled by the PRCM,
those interfaces must be marked with the OCPIF_SWSUP_IDLE flag.
Otherwise, the "interface clock" will always have a non-zero use
count, and the device won't enter idle. This problem was observed on
N8x0.
Fix the immediate problem by marking the VENC interface with the
OCPIF_SWSUP_IDLE flag. But it's not clear that
"dss_54m_fck"/"dss_tv_fck" is really the correct interface clock for
VENC. It may be that the VENC interface should use a
hardware-autoidling interface clock. This is the situation on OMAP4,
which uses "l3_div_ck" as the VENC interface clock, which can be
autoidled by the PRCM. Clarification from TI is needed.
Problem found and patch tested on N8x0 by Tony Lindgren
<tony@atomide.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Senthilvadivu Guruswamy <svadivu@ti.com>
Cc: Sumit Semwal <sumit.semwal@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The driver provides the information regarding the ocp errors
that gets logged in the interconnect. The error information
gives the detail regarding the target that was attempted
to be accessed and its corresponding address.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
The l3 interconnect device is build with all the data required
to handle the error logging. The data is extracted from the
hwmod data base.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: sricharan <r.sricharan@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Add the address spaces, irqs of the l3 interconnect to the
hwmod data. The hwmod change is aligned with Benoit Cousson.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: sricharan <r.sricharan@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
The driver provides the information regarding the ocp errors
that gets logged in the interconnect.The error info provides
the details regarding the master or the target that
generated the error, type of error and the corresponding address.
The stack dump is also provided.
Signed-off-by: sricharan <r.sricharan@ti.com>
[r.sricharan@ti.com: Enhacements, major cleanup and made it functional]
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[santosh.shilimkar@ti.com: Driver design changes as per OMAP4 version]
Signed-off-by: Felipe Balbi <balbi@ti.com>
[balbi@ti.com: Initial version of the driver]
Acked-by: Benoit Cousson <b-cousson@ti.com>
The l3 interconnect device is build with all the data required
to handle the error logging. The data is extracted from the
hwmod database.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Add the address spaces, irqs of the l3 interconnect to the
hwmod data. The hwmod changes are aligned with Benoit Cousson.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Now we used standard SZ_* macros instead of self defined *_SIZE macros. This
patch removes all such unused *_SIZE macros for spear3xx & 6xx.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Resource size required mostly is 4K for all devices, whereas currently
reserved space is much beyond that. This patch replaces SIZE macro's used at
multiple places with SZ_4K.
Reviewed-by: Stanley Miao <stanley.miao@windriver.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Order of declarations should be: pmx_devs, shirq support, amba_devices,
plat_devices, routines. This patch moves gpio_device below shirq support.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Device name of SD/MMC/SDIO controller in linux is sdhci. To maintain
consistency across all spear code, rename sdio to sdhci.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch makes inclusion of hardware.h and spear.h consistent over all spear
variants. Now we will include hardware.h, wherever we need to use hardware
macros. spear.h will be automatically included by hardware.h
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Order of inclusion of .h files must be: <linux/...>, <asm/...>, <plat/...>,
<mach/...>. This patch corrects this ordering whereever it is not followed.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- Add a dummy clk_set_rate() function. This is required for compilation
of a few drivers.
- Make functions in plat-spear/clock.c more generic over all SPEAr
platforms.
- Add div_factor in struct clk for clks with .recalc = follow_parent
- Change type of register pointers to void __iomem *
Reviewed-by: Stanley Miao <stanley.miao@windriver.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move platform specific timer initialization code is moved into platform
specific files.
Reviewed-by: Jamie Iles <jamie@jamieiles.com>
Reviewed-by: Stanley Miao <stanley.miao@windriver.com>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- compile padmux only for spear3xx
- padmux initialization code rearranged in evaluation board and machine
files.
Reviewed-by: Stanley Miao <stanley.miao@windriver.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add IOMEM(x) definition, and use it with MISC_BASE for SPEAr platform.
With this there is no need to typecast misc macros to (unsigned int *).
Reviewed-by: Stanley Miao <stanley.miao@windriver.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use straight 64-bit values as 64-bit operations are fairly efficient on ARM.
Comparing the asm output with and without KTIME_SCALAR, using 64-bit math
generates clearly better code.
Comparing kernel/hrtimer.c .text size, it goes from 0x1414 to 0x119c with
this change.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The simply expanded variable may be evaluated before the target file for
the stat command is up to date or even exists. Switching to a recursively
expanded variable move the execution of the stat command to the location
where LDFLAGS_vmlinux is actually used, fixing the dependency issue
introduced by patch #6746/1.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Few architectures combine the GIC with an external interrupt
controller. On such systems it may be necessary to update both
the GIC registers and the external controller's registers to control
IRQ behavior.
This can be addressed in couple of possible methods.
1. Export common GIC routines along with 'struct irq_chip gic_chip'
and allow architectures to have custom function by override.
2. Provide architecture specific function pointer hooks
within GIC library and leave platforms to add the necessary
code as part of these hooks.
First one might be non-intrusive but have few shortcomings like arch
needs to have there own custom gic library. Locks used should be
common since it caters to same IRQs etc. Maintenance point of view
also it leads to multiple file fixes.
The second probably is cleaner and portable. It ensures that all the
common GIC infrastructure is not touched and also provides archs to
address their specific issue.
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Colin Cross <ccross@android.com>
Tested-by: Colin Cross <ccross@android.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Populate the l2x0 set_debug function pointer with OMAP secure call
and enable the PL310 Errata 727915
This patch has dependency on the earlier patch
ARM: l2x0: Errata fix for flush by Way operation can cause data
corruption
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
PL310 implements the Clean & Invalidate by Way L2 cache maintenance
operation (offset 0x7FC). This operation runs in background so that
PL310 can handle normal accesses while it is in progress. Under very
rare circumstances, due to this erratum, write data can be lost when
PL310 treats a cacheable write transaction during a Clean & Invalidate
by Way operation.
Workaround:
Disable Write-Back and Cache Linefill (Debug Control Register)
Clean & Invalidate by Way (0x7FC)
Re-enable Write-Back and Cache Linefill (Debug Control Register)
This patch also removes any OMAP dependency on PL310 Errata's
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The i2c_board_info entry supporting AIC23 codec was added into
the i2c2 bus.
Signed-off-by: Abhilash K V <abhilash.kv@ti.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 3cf32bba8c ("OMAP: McBSP: Convert
McBSP to platform device model") breaks compilation with non-multi-OMAP1
configs:
CC arch/arm/mach-omap1/mcbsp.o
arch/arm/mach-omap1/mcbsp.c: In function 'omap1_mcbsp_init':
arch/arm/mach-omap1/mcbsp.c:384: warning: dereferencing 'void *' pointer
arch/arm/mach-omap1/mcbsp.c:387: error: invalid use of void expression
arch/arm/mach-omap1/mcbsp.c:390: warning: dereferencing 'void *' pointer
arch/arm/mach-omap1/mcbsp.c:393: error: invalid use of void expression
Fix by avoiding NULL dereferences.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
[tony@atomide.com: updated description not to remove unnecessary branch name]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Allow the MSM8960 IOMMU to access its page tables directly
through the L2 cache.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Don't read from V2Pxx command registers when doing
iova-to-phys operations. These registers are write-only and
reading the value before modifying the VA bits is
unnecessary.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Remove the depencency on the IOMMU IDR register, as it may
not be accessible depending on the security configuraton.
This involves moving the NCB field of IDR into the platform
data.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Use ASID tags in the TLB instead of VMID tags in
preparation for changes to the secure environment.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Clean up the clock control code in the probe calls, and add
support for controlling the clock for the IOMMU bus
interconnect. With the (proper) clock driver in place, the
clock control logic in the probe function can be made much
cleaner since it does not have to deal with the placeholder
driver anymore.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Reviewed-by: Trilok Soni <tsoni@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Add clock control to the IOMMU driver. The IOMMU bus clock
(and potentially an AXI clock) need to be on to gain access
to IOMMU registers. Actively control these clocks when
needed instead of leaving them on.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
This typo was fixed in 46e3f30 (mx25: fix spi device registration typo), but a
the merge at 0e44e059 (Merge commit 'v2.6.37-rc4' into imx-for-2.6.38) resolved
the merge conflict wrongly.
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* 's5p-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: S3C64XX: Update regulator names for debugfs compatiblity on SMDK6410
ARM: S3C64XX: Fix build with WM1190 disabled and WM1192 enabled on SMDK6410
ARM: S3C64XX: Reduce output of s3c64xx_dma_init1()
ARM: S3C64XX: Tone down SDHCI debugging
ARM: S3C64XX: Add clock for i2c1
ARM: S3C64XX: Staticise non-exported GPIO to interrupt functions
ARM: SAMSUNG: Include devs.h in dev-uart.c to prototype devices
ARM: S3C64XX: Fix keypad setup to configure correct number of rows
ARM: S3C2440: Fix usage gpio bank j pin definitions on GTA02
ARM: S5P64X0: Fix number of GPIO lines in Bank F
ARM: S3C2440: Select missing S3C_DEV_USB_HOST on GTA02
Add a clockdomain to the GPTIMER7 interface and 2430 HSMMC2 functional
clocks - both were previously missing them.
Also, the 2430 mmchs1_fck is in core_l3_clkdm, but should be in
core_l4_clkdm; fix this.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch fixes these warnings when building kernel for OMAP3EVM
only.
CC arch/arm/mach-omap2/clockdomains2xxx_3xxx_data.o
arch/arm/mach-omap2/clockdomains2xxx_3xxx_data.c:95: warning:
'dsp_24xx_wkdeps' defined but not used
arch/arm/mach-omap2/clockdomains2xxx_3xxx_data.c:119: warning:
'mpu_24xx_wkdeps' defined but not used
arch/arm/mach-omap2/clockdomains2xxx_3xxx_data.c:147: warning:
'core_24xx_wkdeps' defined but not used
The problem should be noticed when building for other OMAP3
platforms (only) as well.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
After commit 81b34fbecb ("OMAP2 clock:
split OMAP2420, OMAP2430 clock data into their own files"), it's
possible to remove dsp_irate_ick from the OMAP2420 and OMAP2430 clock
files. It was originally only needed due to a 2420/2430 clock tree difference,
and now that the data is in separate files, it's superfluous.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Remove the DPLL rate tolerance code that is called during rate
rounding. As far as I know, this code is never used, since it's been
more important for callers of the DPLL round_rate()/set_rate()
functions to obtain an exact rate than it is to save a relatively
small amount of power.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Bail out before we take the clockfw_lock spinlock if the corresponding
OMAP1 or OMAP2+ clock function is not defined. The intention is to
reduce and simplify the work that is done inside the spinlock.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The parent of the interface clocks for GPTIMER1, MPU_WDT,
SYNCTIMER_32K, SCM, WDT1, and the ICR (2430 only) were all listed as
being l4_ck. This isn't accurate; these modules exist inside the WKUP
domain, and the interface clock to these modules runs at the SYS_CLK
rate rather than the CORE L4 rate.
So, create a new clock "wu_l4_ick", similar to the OMAP3
"wkup_l4_ick", that serves as the parent for these clocks.
Also, these clocks were listed as existing inside core_l4_clkdm;
wkup_clkdm is probably more accurate.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The OMAP2420/2430 external 32-kHz low-frequency oscillator is a 32768
Hz oscillator, not a 32,000 Hz oscillator[1][2]. Fix this in the clock
tree.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
1. OMAP2420/22 Multimedia Processor Data Manual, Version P [SWPS019P],
section 5.1.4 "External 32-kHz CMOS Clock" (note that it refers to
a "32.768-kHz" clock; this presumably should be "32.768-KHz")
2. OMAP2430 Multimedia Processor ES2.1 Data Manual, Version V [SWPS023V],
section 5.1.4 "External 32-kHz CMOS Clock" (note that it refers to
a "32.768-kHz" clock; this presumably should be "32.768-KHz")
Several clocks are listed as having the core L4 clock as their parent,
when they are actually derived from the L3 clock. Fix these.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
At this point in time, there's no reason for this header file to be in
plat-omap/include/plat/voltage.h. It should not be included by device
drivers, and the code that uses it is currently all under mach-omap2/.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
There's no reason for this header file to be in
plat-omap/include/plat/smartreflex.h. The hardware devices are in
OMAP2+ SoCs only. Leaving this header file in plat-omap causes
problems due to cross-dependencies with other header files that should
live in mach-omap2/.
Thanks to Benoît Cousson <b-cousson@ti.com> for suggesting the removal
of the smartreflex.h include from the OMAP3xxx hwmod data.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
These CM_AUTOIDLE bits are now set by the clock code via the common PM
code in mach-omap2/pm.c.
N.B.: The pm24xx.c code that this patch removes didn't ensure that the
CM_AUTOIDLE bits were set for several 2430-only modules, such as
GPIO5, MDM_INTC, MMCHS1/2, the modem oscillator clock, and USBHS.
Similarly, the pm34xx.c code that this patch removes didn't ensure
that the CM_AUTOIDLE bits were set for USIM and the AM3517 UART4.
Those cases should now be handled.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Mark each interface clock with a corresponding CM_AUTOIDLE bit with
a clkops that has the allow_idle/deny_idle function pointers populated.
This allows the OMAP clock framework to enable and disable autoidle for
these clocks.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Mark each interface clock with a corresponding CM_AUTOIDLE bit with
a clkops that has the allow_idle/deny_idle function pointers populated.
This allows the OMAP clock framework to enable and disable autoidle for
these clocks.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
OMAP2430 and OMAP3xxx have modem autoidle bits that are actually
attached to clocks with CM_FCLKEN bits; add the code and data to
handle these.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Mark each interface clock with a corresponding CM_AUTOIDLE bit with
a clkops that has the allow_idle/deny_idle function pointers populated.
This allows the OMAP clock framework to enable and disable autoidle for
these clocks.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Add sdrc_ick to the OMAP2420 clock data so the clock code can control
the CM_AUTOIDLE bit associated with this clock.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Add interface clock type code with autoidle enable/disable support.
The clkops structures created in this file will be used for all
OMAP2/3 interface clocks with autoidle support. They will enable the
clock framework to control interface clock autoidle directly.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Place some comments in the OMAP oscillator clock control code to note that
its autoidle mode should eventually be controlled via the new OMAP clockfw
autoidle control interface.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
OMAP2xxx devices have two on-chip APLLs. These APLLs can
automatically enter idle when not in use. Connect the APLL autoidle
code to the clock code, so that the clock framework can handle this
process. As part of this patch, remove the code in mach-omap2/pm24xx.c
that previously handled APLL autoidle control.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Add the necessary code and data to allow the clock framework to enable
and disable the OMAP2 DPLL autoidle state. This is so the direct
register access can be moved out of the mach-omap2/pm24xx.c code, and other
code that needs to control this (e.g., CPUIdle) can do so via an API.
As part of this patch, remove the pm24xx.c code that formerly wrote
directly to the autoidle bits.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Some drivers wish to know whether the device that they control can
ever lose context, for example, when the device's enclosing
powerdomain loses power. They can use this information to determine
whether it is necessary to save and restore device context, or whether
it can be skipped. Implement the powerdomain portion of this by
adding the function pwrdm_can_ever_lose_context(). This is not for
use directly from driver code, but instead is intended to be called
from driver-subarch integration code (i.e., arch/arm/*omap* code).
Currently, the result from this function should be passed into the
driver code via struct platform_data, but at some point this should
be part of some common or OMAP-specific device code.
While here, update file copyrights.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The bank power state bitfields in the powerdomain data are
encoded incorrectly. These fields are intended to be bitfields,
representing a set of power states that the memory banks support.
However, when only one power state was supported by a given bank,
the field was incorrectly set to the bit shift -- not the mask.
While here, update some file copyrights.
The OMAP4 autogeneration scripts have been updated accordingly.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Mark the WKUP powerdomain as being always on -- at least, as long as the
chip has power. This will be used to enable the powerdomain code to
determine whether a given powerdomain is ever able to power off. While
here, update the file copyright.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch enables lcd and backlight drivers in NURI board.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds the parent clock for watchdog timer for EXYNOS4.
Signed-off-by: Inderpal Singh <inderpal.s@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Currently all boards using the s3c2410_udc driver use a GPIO to control the
state of the pullup, as a result the same code is reimplemented in each board
This patch changes these boards to use the common implementation for GPIO
controlled pullup in the UDC driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently all boards using the s3c2410_udc driver use a GPIO to control the
state of the pullup, as a result the same code is reimplemented in each board
file.
This patch adds support for using a GPIO to control the pullup state to the udc
driver, so the boards can use a common implementation.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Most revisions of the OMAP4 Blaze/SDP platform do not have
the EHCI signals routed by default. The pads are routed
for the alternate HSI functionality instead, and explicit
board modifications are needed to route the signals to
the USB PHY on the board.
Also, turning on the PHY connected to the EHCI port causes
a board reboot during bootup due to an unintended short
on the rails - this affects many initial revisions of the
board, and needs a minor board mod to fix (or as a
workaround, one should not attempt to power on the
USB PHY).
Given that these boards need explicit board mods to even
get EHCI working (separate from the accidental short above),
we should not attempt to enable EHCI by default.
So drop the EHCI support from the board files for the
Blaze/SDP platforms.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Keshava Munegowda <keshava_mgowda@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is to add pad control helper macro to make the code easy
to read. The need is being seen when adding pad definitions for
LCDIF which gets ~30 pads to define.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This fixes:
arch/arm/kernel/built-in.o: In function `__irq_svc':
io.c:(.text+0x2e0): undefined reference to `avic_base'
arch/arm/kernel/built-in.o: In function `__irq_usr':
io.c:(.text+0x4c8): undefined reference to `avic_base'
arch/arm/mach-mxc91231/built-in.o: In function `mxc91231_init_irq':
magx-zn5.c:(.init.text+0x18): undefined reference to `mxc_init_irq'
and was broken by
c7259df (ARM i.MX irq: Compile avic irq code only on SoCs that need it)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Move to SOC_SOC_IMX3X.
Leave ARCH_MX31/35 definitions there, in case some place prevent multi-soc
single image.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Move to SOC_SOC_IMX5X. Leave only places which prevent multi-soc
using ARCH_MX5X.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The boards are currently using otg_ulpi_create and mxc_ulpi_access_ops,
both are only present if CONFIG_USB_ULPI is set. To remove the need of
ifdefs in the board code introduce a imx_otg_ulpi_create functions
which expands to a static inline function if compiled without ulpi.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The platform data for the otg port is present but never used, so
remove it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Daniel Mack <daniel@caiaq.de>
On mx53_evk board only RX/TX pins are used on UART3.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
On mx53_smd board only RX/TX pins are used on UART2.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
changes since v2:
- use v3 and v4 for specifying the ip version instead of i.MX23/28.
This is a better namespace when future versions are added.
- rename mach/fb.h to mach/mxsfb.h
changes since v1:
- Add a LCDC_ prefix to the register names.
- use set/clear registers where appropriate
- protect call to mxsfb_disable_controller() in mxsfb_remove()
with a (host->enabled) as suggested by Lothar Wassmann
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: linux-fbdev@vger.kernel.org
While at it remove some useless consts from unsigned int arguments.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This fixes the following warning in a mx3_defconfig build:
arch/arm/mach-mx3/mach-bug.c: In function 'bug_board_init':
arch/arm/mach-mx3/mach-bug.c:47: warning: passing argument 1 of 'mxc_iomux_setup_multiple_pins' discards qualifiers from pointer target type
While at it remove some useless consts from unsigned int arguments.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Visstrim_M10 boards have an TI tlv320aic3204 codec
attached to SSI1.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
It seems vim's autocompletion played tricks on me without me noticing.
This was intruduced in
97976e2 (ARM: mx3: use .init_early to initialize cpu type, reset address and iomuxer)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
According to the "i.MX35 (MCIMX35) Multimedia Applications Processor
Reference Manual" the correct address for the pad control register
IOMUXC_SW_PAD_CTL_PAD_ATA_DATA3 is 0x06ec, not 0x6e8.
Signed-off-by: Ryan Lortie <desrt@desrt.ca>
Acked-by: Marc Reilly <marc@cpdesign.com.au>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Based on code created by Lothar Waßmann, Sascha Hauer, Wolfram Sang and
me.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
It is used for example in the i2c driver which can be compiled modular.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
The regulator API ifdefs itself out when not enabled
so there is no need for users to do this.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: edited description]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add support for CS4271 SPI-connected CODEC to EDB93xx.
Signed-off-by: Alexander Sverdlin <subaparts@yandex.ru>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
[np: used min_t() as suggested by Sergei Shtylyov <sshtylyov@mvista.com>]
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Originally the FPGA ID checking switch statement left disabled all the
TS implemented FPGA devices if the ID was unknown to it. Michael Spang
created a fix in f9b1184e that changed the default to enable the devices
in the event TS silently release more revisions into the wild, this
unfortunately breaks custom FPGA bitstreams.
This patch amends the switch statement so that the TS devices are only
enabled if on the revision number is unknown (whilst the magic matches).
Changelog:
v2: neater implementation and some cosmetic changes
v1: initial release <20110305112937.GA22117@chipmunk>
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
When the manufacturer increases the revision number the platform
devices for the RTC, NAND, and RNG disappear. We should assume
new revisions have these devices instead of assuming they do not.
Signed-off-by: Michael Spang <mspang@csclub.uwaterloo.ca>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
The following commit: 38698be:
OMAP2+: clockevent: set up GPTIMER clockevent hwmod right before timer init
Fixed properly the issue with early init for the timer1
So reverts commit 3b03b58dab that is now
generated a warning at boot time.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The debugfs support added to the regulator API (which has been merged
in during this merge window) creates directories for regulators named
after the display names for the regulators so replace / as a separator
for multiple supplies with + in the SMDK6410 machine.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Avoid relying on implicit inclusion of machine.h
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Reduce the logging output of s3c64xx_dma_init1() as it is not useful
for normal bootup (and we get an overall indication of the registration
of the PL180 DMA block).
This removes the following output from the log:
s3c64xx_dma_init1: registering DMA 0 (e0808100)
s3c64xx_dma_init1: registering DMA 1 (e0808120)
s3c64xx_dma_init1: registering DMA 2 (e0808140)
s3c64xx_dma_init1: registering DMA 3 (e0808160)
s3c64xx_dma_init1: registering DMA 4 (e0808180)
s3c64xx_dma_init1: registering DMA 5 (e08081a0)
s3c64xx_dma_init1: registering DMA 6 (e08081c0)
s3c64xx_dma_init1: registering DMA 7 (e08081e0)
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The MMC core calls s3c6400_setup_sdhcp_cfg_card() very frequently, causing
the log message in there at KERN_INFO to be displayed a lot which is slow
and overly chatty. Convert the message into a pr_debug() to tone this down.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The clock for i2c1 has been missing for a while, add it to the list of
clocks for the system and ensure it is initialised at startup.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
No need to put these in the global namespace and sparse gets upset.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Ensures that the declaration agrees with the definition and makes sparse
happy.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The call to s3c_gpio_cfgrange_nopull() takes a size and base
but this looks like it is trying to do base and end. This means
it is configuring too many GPIOs and on the case of the Cragganmore
means we're seeing an overflow of the ROW pins causing problems
with the keyboard driver.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The gta02 header file still uses the old S3C2410_GPJx defines instead of the
S3C2410_GPJ(x) macro. Since the S3C2410_GPJx defines have already been removed
this causes the following build failure:
sound/soc/samsung/neo1973_wm8753.c: In function 'lm4853_set_spk':
sound/soc/samsung/neo1973_wm8753.c:259: error: 'S3C2440_GPJ2' undeclared (first use in this function)
sound/soc/samsung/neo1973_wm8753.c:259: error: (Each undeclared identifier is reported only once
sound/soc/samsung/neo1973_wm8753.c:259: error: for each function it appears in.)
sound/soc/samsung/neo1973_wm8753.c: In function 'lm4853_get_spk':
sound/soc/samsung/neo1973_wm8753.c:267: error: 'S3C2440_GPJ2' undeclared (first use in this function)
sound/soc/samsung/neo1973_wm8753.c: In function 'lm4853_event':
sound/soc/samsung/neo1973_wm8753.c:276: error: 'S3C2440_GPJ1' undeclared (first use in this function)
sound/soc/samsung/neo1973_wm8753.c: At top level:
sound/soc/samsung/neo1973_wm8753.c:439: error: 'S3C2440_GPJ2' undeclared here (not in a function)
sound/soc/samsung/neo1973_wm8753.c:440: error: 'S3C2440_GPJ1' undeclared here (not in a function)
This patches fixes the issue by doing a s,S3C2410_GPJ([\d]+),S3C2410_GPJ(\1),g
on the file.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch modifies the number of total GPIO lines for Bank F
for Samsung S5P6440 and S5P6450 SoCs from 2 to 16.
This is necessary as the GPIO lines from 0 to 13 are reserved
and only lines 14 and 15 are used. As during initialization,
the line number starts at 0, putting 2 does not solve the
intended purpose.
Signed-off-by: Banajit Goswami <banajit.g@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The gta02 mach file references the ohci device.
So we need to select S3C_DEV_USB_HOST to have the device available.
This fixes the following linker errors:
arch/arm/mach-s3c2440/built-in.o: In function 'gta02_machine_init':
mach-gta02.c:(.init.text+0x370): undefined reference to 's3c_ohci_set_platdata'
arch/arm/mach-s3c2440/built-in.o:(.init.data+0xac): undefined reference to 's3c_device_ohci'
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds Samsung ARMLEX4210 board support file
which is based on Exynos4210.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
[kgene.kim@samsung.com: added clk_type for hsmmc3]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds basic definitions for MAX8952 & LP3974 (MAX8998
compatible) PMICs for UniversalC210 board. Power consumers for the
device drivers will be added later. These two PMICs occupy I2C5 bus.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds Samsung NURI board support.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Currently tegra_pcie_init is effectively called as subsys_initcall. With
multiplatform kernel this may cause hangs on boards that don't intend to
support Tegra2 PCI-e. Ensure that TrimSlice board code initializes PCI-e
only when actually running on the TrimSlice.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Colin Cross <ccross@android.com>
Move tegra_pcie_power_off before tegra_pcie_power_on for clean addition
of PCIE power gating
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Colin Cross <ccross@android.com>
These are not currently used anywhere, but when the relevant
peripherals are enabled on the Dove port, the IRQ numbers should be
passed into the drivers via platform device resources rather than
having the drivers get them from platform headers directly.
Signed-off-by: Lennert Buytenhek <buytenh@secretlab.ca>
Acked-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
This patch makes the various mach dirs that use the plat-orion GPIO
code pass in GPIO-related platform info (GPIO controller base address,
secondary base IRQ number, etc) explicitly, instead of having
plat-orion get those values by including a mach dir include file --
the latter mechanism is problematic if you want to support multiple
ARM platforms in the same kernel image.
Signed-off-by: Lennert Buytenhek <buytenh@secretlab.ca>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
This patch makes the various mach dirs that use the plat-orion time
code pass in timer and bridge addresses explicitly, instead of having
plat-orion get those values by including a mach dir include file --
the latter mechanism is problematic if you want to support multiple
ARM platforms in the same kernel image.
Signed-off-by: Lennert Buytenhek <buytenh@secretlab.ca>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
This patch declares the i2c audio codec and initialise audio.
It's adding the alc5621 codec in the i2c board info and is calling
kirkwood_audio_init() to initialize kirkwood audio.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
New FPGA revisions have been released and seen in the wild on the
platform, so it's time to update the list.
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Initialize PCIE1 on the 6282-based QNAP TS-419P+ since it has a Marvell 9125
SATA chip on each PCI bus.
Signed-off-by: Zintis Pētersons <zintis.petersons@abcsolutions.lv>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Use the machine-specific kexec_reinit hook to make sure
PCIe is enabled before starting a new kernel.
Signed-off-by: Eric Cooper <ecc@cmu.edu>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
PCIe may have been disabled (by kirkwood_clock_gate)
if this kernel was started by kexec. Make sure PCIe
is enabled before attempting to access the device ID
register, otherwise the system will hang.
Signed-off-by: Eric Cooper <ecc@cmu.edu>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Provide the option to call a machine-specific function
before kexec'ing a new kernel.
Signed-off-by: Eric Cooper <ecc@cmu.edu>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Santosh Shilimkar
Stephen Boyd
Tony Lindgren
Dave Martin
Nicolas Pitre
Will Deacon
Russell King
Ilia Mirkin
Richard Zhu
Tero Kristo
Paul Walmsley
Kishon Vijay Abraham I
omar ramirez
Rajendra Nayak
Avinash.H.M
Tarun Kanti DebBarma
Benoit Cousson
Shawn Guo
Stepan Moskovchenko
Felipe Balbi
Anand S Sawant
Sanjeev Premi
Thara Gopinath
Kevin Hilman
Vasiliy Kulikov
Nishanth Menon
Ricardo Salveti de Araujo
Linus Walleij
sricharan
Shiraz Hashim
viresh kumar
Rob Herring
Abhilash Vadakkepat Koyamangalath
Baruch Siach
Alberto Panizzo
Linus Torvalds
Seungwhan Youn
Donghwa Lee
Inderpal Singh
Lars-Peter Clausen
Anand Gadiyar
Uwe Kleine-König
Richard Zhao
Sascha Hauer
Gwenhael Goavec-Merou
Fabio Estevam
Wolfram Sang
Javier Martin
Ryan Lortie
Eric Bénard
Lothar Waßmann
Kyungmin Park
Alexander Sverdlin
Alexander Clouter
Michael Spang
Mark Brown
Ben Dooks
Banajit Goswami
ALIM AKHTAR
Marek Szyprowski
Minkyu Kang
Kuninori Morimoto
Mike Rapoport
Lennert Buytenhek
Nicolas Pitre
Arnaud Patard
Zintis Pētersons
Eric Cooper