If we have not got any pdus for recv_timeout seconds, then we will
send a iscsi ping/nop to make sure the target is still around. The
problem is if this is a slow link, and the ping got queued after
the data for a data_out (read), then the transport code could think
the ping has failed when it is just slowly making its way through
the network. This patch has us check if we are making progress while
the nop is outstanding. If we are still reading in data, then we
do not fail the session at that time.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Everytime we read in a pdu libiscsi will update a tracking field.
It uses this to decide when to check if the transport might be bad.
If we have not got data in recv_timeout seconds then we will
send a iscsi ping/nop.
If we are on a slow link then it could take a while to read in all
the data for a data_in. In that case we might send a ping/nop when
we do not need to or we might drop a session thinking it is bad
when the lower layer is making forward progress on it.
This patch has libiscsi_tcp update the recv tracking for each skb
(basically network packet from our point of view) instead of the
entire iscsi pdu+data, so we account for these cases where data is
coming in slowly.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
If we are responding to a nop from the target by sending our nop,
and the session is getting torn down, then iscsi_start_session_recovery
could set the conn stop bits while the recv path is sending the nop
response and we will hit the bug ons in __iscsi_conn_send_pdu.
This has us check the state in __iscsi_conn_send_pdu and fail all
incoming mgmt IO if we are not logged in and if the pdu is not login
related. It also changes the ordering of the setting of conn stop state
bits so they are set after the session state is set (both are set under
the session lock).
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This has iscsi_data_in_rsp call iscsi_update_cmdsn when a pdu is
completed like is done for other pdu's that are don.
For libiscsi_tcp, this means that it calls iscsi_update_cmdsn when
it is handling the pdu internally to only transfer data, but if there is
status then it does not need to call it since the completion handling
will do it.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
bnx2i needs to be able to look up mgmt task like login and nop, because
it does some processing of them on the completion path. This exports
iscsi_itt_to_task so it can look up the task.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
If we could not allocate the initiator name or some other id like
the hwaddress or netdev, then userspace could deal with the failure
by just running in a dregraded mode.
Now we want to be able to switch values for the params and we
want some feedback, so this patch will check if a string like
the initiatorname could not be allocated and return an error.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
bnx2i does not have one. It currently preallocates the bdt
when the session is setup.
We probably want to change that to a dma pool, then allocate from
the pool in the alloc pdu. Until then check if there is a alloc
pdu callout.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When we create the tcp/ip connection by calling ep_connect, we currently
just go by the routing table info.
I think there are two problems with this.
1. Some drivers do not have access to a routing table. Some drivers like
qla4xxx do not even know about other ports.
2. If you have two initiator ports on the same subnet, the user may have
set things up so that session1 was supposed to be run through port1. and
session2 was supposed to be run through port2. It looks like we could
end with both sessions going through one of the ports.
Fixes for cxgb3i from Karen Xie.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
drivers/scsi/NCR_D700.c: In function `NCR_D700_probe':
drivers/scsi/NCR_D700.c:322: warning: passing argument 2 of `request_irq' from incompatible pointer type
drivers/scsi/NCR_D700.c:322: warning: passing argument 2 of `request_irq' from incompatible pointer type
drivers/scsi/NCR_D700.c:322: warning: passing argument 2 of `request_irq' from incompatible pointer type
Signed-off-by: Zhenwen Xu <helight.xu@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Using sticky field to improve retrieve performance by eliminating some
lookups in . Remove some spurious casts.
Signed-off-by: Ying Chu <jasonchu@marvell.com>
Signed-off-by: Andy Yan <ayan@marvell.com>
Signed-off-by: Ke Wei <kewei@marvell.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Utilize DECLARE_BITMAP to define the tags array.
Signed-off-by: Ying Chu <jasonchu@marvell.com>
Signed-off-by: Andy Yan <ayan@marvell.com>
Signed-off-by: Ke Wei <kewei@marvell.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Null pointer check to avoid corruption.
Signed-off-by: Ying Chu <jasonchu@marvell.com>
Signed-off-by: Andy Yan <ayan@marvell.com>
Signed-off-by: Ke Wei <kewei@marvell.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
TMF task should be issued with Interrupt Disabled, or Deadlock may take place.
Clean-up unused parameters and conditonal lock.
Signed-off-by: Ying Chu <jasonchu@marvell.com>
Signed-off-by: Andy Yan <ayan@marvell.com>
Signed-off-by: Ke Wei <kewei@marvell.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Correct frame type setting according to parameter.
Signed-off-by: Ying Chu <jasonchu@marvell.com>
Signed-off-by: Andy Yan <ayan@marvell.com>
Signed-off-by: Ke Wei <kewei@marvell.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The ipr driver can hang if it encounters enough PCI errors
to trigger the permanent error handler. The driver will attempt
to initiate a "bringdown" of the adapter and fail all pending
ops back. However, this bringdown is unlike any other bringdown
of the adapter in the code as the driver. In this code path we
end up failing back ops with allow_cmds still set to 1. This results
in some commands, the HCAM commands in particular, getting immediately
re-issued to the adapter on the done call, which results in
an infinite loop in ipr_fail_all_ops. Fix this by setting allow_cmds
to zero in this path.
Signed-off-by: Kleber S. Souza <klebers@linux.vnet.ibm.com>
[brking@linux.vnet.ibm.com: alternate patch substituted]
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
I had to set CONFIG_SCSI_MULTI_LUN to y in order to get my SE W595
working when plugging it as a mass storage. Looking at SCSI option to
get a phone behaving correctly was convoluted to say the least. There
are quite a few other reports about USB card readers needing this option
as well. This patch improves the help text to make the use of the option
more obvious.
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch fixes the GCC 4.4 warning reported by David Binderman and Sergey
Senozhatsky. The old version was working correctly but was not easy to read.
Signed-off-by: Kai Makisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
scsi timeout on two or more devices may cause extremely long execution
time for user applications because SDEV_OFFLINE state is changed to
SDEV_RUNNING state during scsi error recovery procedures triggered by
a bus reset or a host reset of scsi LLD, and scsi timeout can happens
on the same devices many times.
This happens because scsi_internal_device_unblock() changes device's
state to SDEV_RUNNING even if a device in other states than SDEV_BLOCK,
while the following two transitions are required in this function.
SDEV_BLOCK -> SDEV_RUNNING
SDEV_CREATED_BLOCK -> SDEV_CREATED
Otherwise, it returns -EINVAL.
Signed-off-by: Takahiro Yasui <tyasui@redhat.com>
[matthew@wil.cx: supplied rewritten base for patch]
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fix function declarations:
drivers/scsi/fcoe/fcoe.c:1356:28: warning: non-ANSI function declaration of function 'fcoe_dev_setup'
drivers/scsi/libfc/fc_rport.c:1293:20: warning: non-ANSI function declaration of function 'fc_setup_rport'
drivers/scsi/libfc/fc_rport.c:1302:23: warning: non-ANSI function declaration of function 'fc_destroy_rport'
[jejb: fixed wrong doc in comment noticed during inspection]
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Marking the ipr clean up function ipr_remove() as __devexit and using
__devexit_p() macro in its address reference.
Signed-off-by: Kleber Sacilotto de Souza <kleber@linux.vnet.ibm.com>
Reported-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
During device discovery read capacity fails with 0x020401 and sets the
device size to 0. As a reason any I/O submitted to this path gets
killed at sd_prep_fn with BLKPREP_KILL. This patch is to retry for
0x020401. NEED_RETRY in scsi_decide_disposition does not give
sufficient time for the device to become ready.
Signed-off-by: Vijay Chauhan <vijay.chauhan@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Make the sym53c8xx_2 driver slave_alloc/destroy less unsafe. References
to the destroyed LCB are cleared from the target structure (instead of
leaving a dangling pointer), and when the last LCB for the target is
destroyed the reference to the upper layer target data is cleared. The
host lock is used to prevent a race with the interrupt handler. Also
user commands are prevented for targets with all LCBs destroyed.
Signed-off-by: Aaro Koskinen <Aaro.Koskinen@nokia.com>
Tested-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
(Resent with proper formatting)
Fix for the sym53c8xx_2 driver to initialize lun's to_clear flag after
a bus reset (a failed clear can trigger a bus reset and it should not
be attemped again after that).
Signed-off-by: Aaro Koskinen <Aaro.Koskinen@nokia.com>
Tested-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The driver now waits for the scsi commands associated with a
particular error recovery step to be returned to the mid-layer,
and returns the appropriate SUCCESS or FAILED status. Removes
unneeded polling of chip for interrupts.
This patch also bumps the driver version number.
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Remove some unneeded, inactive and unused code, make some trivial
corrections to comments and a printk, and return a proper status
in qla1280_queuecommand. No fundamental logic changes are made.
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch (as1224) changes the default timeout for INQUIRY commands
from 3 seconds to 20 seconds, which is the value used by Windows for
USB Mass-Storage devices. Some of these devices, like the Corsair
Flash Voyager (see Bugzilla #12188) really do need a long timeout.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This version contains following main changes
- Switch to new layout to support more types of ASIC.
- SSP TMF supported and related Error Handing enhanced.
- Support flash feature with delay 2*HZ when PHY changed.
- Support Marvell 94xx series ASIC for 6G SAS/SATA, which has 2
88SE64xx chips but any different register description.
- Support SPI flash for HBA-related configuration info.
- Other patch enhanced from kernel side such as increasing PHY type
[jejb: fold back in DMA_BIT_MASK changes]
Signed-off-by: Ying Chu <jasonchu@marvell.com>
Signed-off-by: Andy Yan <ayan@marvell.com>
Signed-off-by: Ke Wei <kewei@marvell.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Split mvsas driver into multiple source codes, based on the split
and function distribution found in Marvell's mvsas update.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Zero functional changes, just file movement.
This commit prepares for the upcoming integration of the
Marvell-provided driver update that splits the driver into support
for both 64xx and 94xx chip families.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Read adapter's physical port number from interrupt pin register
and use it instead of pci function number to offset into the
nvram to obtain the port's configuration parameters.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
As it may be useful during debugging to use a specific firmware
image.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Changing a lun's queue depth (/sys/block/sdX/device/queue_depth)
isn't sticky when the device is connected via a QLogic fibre
channel adapter.
The QLogic qla2xxx fibre channel driver dynamically adjusts a
lun's queue depth. If a user has a specific need to limit the
number of commands issued to a lun (say a tape drive, or a shared
raid where the total commands issued to all luns is limited at
the controller level, for example) and writes a limiting value to
/sys/block/sdXX/device/queue_depth, the qla2xxx driver will
silently and gradually increase the queue depth back to the
driver limit of ql2xmaxqdepth. While reducing this value (module
parameter) or increasing the interval between ramp ups
(ql2xqfullrampup) offers the potential for a work around it would
be better to have the option of just disabling the dynamic
adjustment of queue depth.
This patch implements an "off switch" as a module parameter.
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Set the conditional plogi option bit whenever logging in the
fabric management server (if it is already logged in, it does not
need an explicit login; an implicit login suffices).
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Information present in static table is only valid for pre-ISP25xx
adapters.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
srbs used to maintain a reference to the request queue on which
it was enqueued. This is no longer required as the request queue
pointer is now maintained in the scsi host that issues the srb.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Set the module parameter ql2xmultique_tag to 1 to enable this
feature. In this mode, the total number of response queues
created is equal to the number of online cpus. Turning the block
layer's rq_affinity mode on enables requests to be routed to the
proper cpu and at the same time it enables completion of the IO
in a response queue that is affined to the cpu in the request
path.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Set the number of request queues to the module paramater
ql2xmaxqueues. Each vport gets a request queue. The QoS value
set to the request queues determines priority control for queued
IOs. If QoS value is not specified, the vports use the default
queue 0.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Cull and export VN_Port MAC address and VLAN_ID information on
supported FCoE ISPs.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The short-circuit to skip the non-applicable 'full-login-lip'
process on 81xx ISPs was nested too deeply in the 'bus-reset'
routine, as the code in qla2x00_loop_reset() should skip the
whole enable_lip_full_login process. The original code could
cause device tear-down due to the qla2x00_wait_for_loop_ready()
call taking a large amount of time.
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* 'fixes-for-linus' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: Fix kind-of-intr checking against number of interrupts
microblaze: Update Microblaze defconfig
Martin Knoblauch reports that trying to build 2.6.30-rc6-git3 with
RHEL4.3 userspace (gcc (GCC) 3.4.5 20051201 (Red Hat 3.4.5-2)) causes an
internal compiler error (ICE):
drivers/char/random.c: In function `get_random_int':
drivers/char/random.c:1672: error: unrecognizable insn:
(insn 202 148 150 0 /scratch/build/linux-2.6.30-rc6-git3/arch/x86/include/asm/tsc.h:23 (set (reg:SI 0 ax [91])
(subreg:SI (plus:DI (plus:DI (reg:DI 0 ax [88])
(subreg:DI (reg:SI 6 bp) 0))
(const_int -4 [0xfffffffffffffffc])) 0)) -1 (nil)
(nil))
drivers/char/random.c:1672: internal compiler error: in extract_insn, at recog.c:2083
and after some debugging it turns out that it's due to the code trying
to figure out the rough value of the current stack pointer by taking an
address of an uninitialized variable and casting that to an integer.
This is clearly a compiler bug, but it's not worth fighting - while the
current stack kernel pointer might be somewhat hard to predict in user
space, it's also not generally going to change for a lot of the call
chains for a particular process.
So just drop it, and mumble some incoherent curses at the compiler.
Tested-by: Martin Knoblauch <spamtrap@knobisoft.de>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike Christie