* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (163 commits)
omap: complete removal of machine_desc.io_pg_offst and .phys_io
omap: UART: fix wakeup registers for OMAP24xx UART2
omap: Fix spotty MMC voltages
ASoC: OMAP4: MCPDM: Remove unnecessary include of plat/control.h
serial: omap-serial: fix signess error
OMAP3: DMA: Errata i541: sDMA FIFO draining does not finish
omap: dma: Fix buffering disable bit setting for omap24xx
omap: serial: Fix the boot-up crash/reboot without CONFIG_PM
OMAP3: PM: fix scratchpad memory accesses for off-mode
omap4: pandaboard: enable the ehci port on pandaboard
omap4: pandaboard: Fix the init if CONFIG_MMC_OMAP_HS is not set
omap4: pandaboard: remove unused hsmmc definition
OMAP: McBSP: Remove null omap44xx ops comment
OMAP: McBSP: Swap CLKS source definition
OMAP: McBSP: Fix CLKR and FSR signal muxing
OMAP2+: clock: reduce the amount of standard debugging while disabling unused clocks
OMAP: control: move plat-omap/control.h to mach-omap2/control.h
OMAP: split plat-omap/common.c
OMAP: McBSP: implement functional clock switching via clock framework
OMAP: McBSP: implement McBSP CLKR and FSR signal muxing via mach-omap2/mcbsp.c
...
Fixed up trivial conflicts in arch/arm/mach-omap2/
{board-zoom-peripherals.c,devices.c} as per Tony
Since we're now using addruart to establish the debug mapping, we can
remove the io_pg_offst and phys_io members of struct machine_desc.
The various declarations were removed using the following script:
grep -rl MACHINE_START arch/arm | xargs \
sed -i '/MACHINE_START/,/MACHINE_END/ { /\.\(phys_io\|io_pg_offst\)/d }'
[ Initial patch was from Jeremy Kerr, example script from Russell King ]
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Eric Miao <eric.miao at canonical.com>
Only OMAP2+ platforms have the System Control Module (SCM) IP block.
In the past, we've kept the SCM header file in plat-omap. This has
led to abuse - device drivers including it; includes being added that
create implicit dependencies on OMAP2+ builds; etc.
In response, move the SCM headers into mach-omap2/.
As part of this, remove the direct SCM access from the OMAP UDC
driver. It was clearly broken. The UDC code needs an indepth review for
use on OMAP2+ chips.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Cory Maccarrone <darkstar6262@gmail.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Use the new mux function for that.
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move omap2 FS USB platform init code into mach-omap2/usb-fs.c. This will
allow further work later on to use omap hwmod for initializing the
device.
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use smc91x_platdata to setup smc91x, so we can get rid of OMAP specific stuff
in smc91x driver
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move the remaining headers under plat-omap/include/mach
to plat-omap/include/plat. Also search and replace the
files using these headers to include using the right path.
This was done with:
#!/bin/bash
mach_dir_old="arch/arm/plat-omap/include/mach"
plat_dir_new="arch/arm/plat-omap/include/plat"
headers=$(cd $mach_dir_old && ls *.h)
omap_dirs="arch/arm/*omap*/ \
drivers/video/omap \
sound/soc/omap"
other_files="drivers/leds/leds-ams-delta.c \
drivers/mfd/menelaus.c \
drivers/mfd/twl4030-core.c \
drivers/mtd/nand/ams-delta.c"
for header in $headers; do
old="#include <mach\/$header"
new="#include <plat\/$header"
for dir in $omap_dirs; do
find $dir -type f -name \*.[chS] | \
xargs sed -i "s/$old/$new/"
done
find drivers/ -type f -name \*omap*.[chS] | \
xargs sed -i "s/$old/$new/"
for file in $other_files; do
sed -i "s/$old/$new/" $file
done
done
for header in $(ls $mach_dir_old/*.h); do
git mv $header $plat_dir_new/
done
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the low level debug UART io address as per this series.
The change is essential to have CONFIG_DEBUG_LL working.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove the ARM dependency from the generic "onenand" platform device
driver. This change makes the driver useful for other architectures as
well. Needed for the SuperH kfr2r09 board.
Apart from the obvious Kconfig bits, the most important change is the move
away from ARM specific includes and platform data. Together with this
change the only in-tree board code gets an update, and the driver name is
also changed gracefully break potential out of tree drivers.
The driver is also updated to allow NULL as platform data together with a
few changes to make use of resource_size() and dev_name().
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kyungmin Park <kmpark@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Most board-*.c files read configuration data from the bootloader in
their .init_machine() function. This needs to happen earlier, at some
point before omap2_init_common_hw() is called. This is because a
future patch will use the bootloader serial console port information
to enable the UART clocks earlier, immediately after omap2_clk_init().
This is in turn necessary since otherwise clock tree usecounts on
clocks like dpll4_m2x2_ck will be bogus, which can cause the
currently-active console UART clock to be disabled during boot.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
OMAP tags are deprecrated so drop them.
Drop UART config data which decides which UARTs to enable during boot.
This is no longer necessary since serial core code disables clocks
after inactivity.
Background: with new UART idle code, all on-chip UARTs are idled using
a configurable inactivity timer (default 5 seconds.) After the
inactivity timer, UART clocks are disabled automatically.
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some OMAP3 boards (Beagle Cx, Overo, RX51, Pandora) have 2
SDRAM parts connected to the SDRC.
This patch adds the following:
- add a new argument of type omap_sdrc_params struct*
to omap2_init_common_hw and omap2_sdrc_init for the 2nd CS params
- adapted the OMAP boards files to the new prototype of
omap2_init_common_hw
- add the SDRC 2nd CS registers offsets defines
- adapt the sram sleep code to configure the SDRC for the 2nd CS
Note: If the 2nd param to omap2_init_common_hw is NULL, then the
parameters are not programmed into the SDRC CS1 registers
Tested on 3430 SDP and Beagleboard rev C2 and B5, with
suspend/resume and frequency changes (cpufreq).
Signed-off-by: Jean Pihet <jpihet@mvista.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
OMAP_TAGS should vanish soon since they're not generic arm tags.
Most of them can be converted to a platform_data or parsed
from a command line like e.g. serial tag.
For OMAP_TAG_USB we just let boards call omap_usb_init()
passing a pointer to omap_usb_config.
Patch updated by Tony for mainline, basically make
n770 and h4 compile. Also folded in a fix for OSK
by David Brownell <dbrownell@users.sourceforge.net>.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For a given SDRAM clock rate, SDRAM chips require memory controllers
to use a specific set of timing minimums and maximums to transfer data
reliably. These parameters can be different for different memory chips
and can also potentially vary by board.
This patch adds the infrastructure for board-*.c files to pass this
timing data to the SDRAM controller init function. The timing data is
specified in an 'omap_sdrc_params' structure, in terms of SDRC
controller register values. An array of these structs, one per SDRC
target clock rate, is passed by the board-*.c file to
omap2_init_common_hw().
This patch does not define the values for different memory chips, nor
does it use the values for anything; those will come in subsequent patches.
linux-omap source commit is bc84ecfc795c2d1c5cda8da4127cf972f488a696.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix compile by removing remaining omap specific gpio
calls. Based on earlier patches by Jarkko Nikula.
Also remove old GPIO key code, there is already a patch
to do this with gpio_keys.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Most of the omap1 MMC boards got broken by an earlier patch
138ab9f832. If you look closely,
the MMC init funtions are pretty much just stubs.
Remove broken init code to make room for cleaner MMC init code.
Cc: Pierre Ossman <drzeus-mmc@drzeus.cx>
Signed-off-by: Tony Lindgren <tony@atomide.com>
More conversion to the standard GPIO interfaces: stop using
omap_set_gpio_direction() entirely, and switch over to the
gpio_direction_output() call.
Note that because gpio_direction_output() includes the initial
value, this change isn't quite transparent.
- For the call sites which defined an initial value either
before or after setting the direction, that value was used.
When that value was previously assigned afterwards, this
could eliminate a brief output glitch ... and possibly
change behavior. In a few cases (LCDs) several values
were assigned together ... those were re-arranged to match
the explicit sequence provided.
- Some call sites didn't define such a value; so I chose an
initial "off/reset" value that seemed to default to "off".
In short, files touched by this patch might notice some small
changes in startup behavior (with trivial fixes).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
More switchover to the cross-platform GPIO interface:
use gpio_direction_input(), not an OMAP-specific call.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch replaces some legacy OMAP GPIO calls with the "new" (not
really, any more!) calls that work on most platforms.
The calls addressed by this patch are the simple ones to get and set
values ... for code that's in mainline, including the implementations
of those calls.
Except for the declarations and definitions of those calls, all of
these changes were performed by a simple SED script. Plus, a few
"if() set() else set()" branches were merged by hand.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
IRQT_* and __IRQT_* were obsoleted long ago by patch [3692/1].
Remove them completely. Sed script for the reference:
s/__IRQT_RISEDGE/IRQ_TYPE_EDGE_RISING/g
s/__IRQT_FALEDGE/IRQ_TYPE_EDGE_FALLING/g
s/__IRQT_LOWLVL/IRQ_TYPE_LEVEL_LOW/g
s/__IRQT_HIGHLVL/IRQ_TYPE_LEVEL_HIGH/g
s/IRQT_RISING/IRQ_TYPE_EDGE_RISING/g
s/IRQT_FALLING/IRQ_TYPE_EDGE_FALLING/g
s/IRQT_BOTHEDGE/IRQ_TYPE_EDGE_BOTH/g
s/IRQT_LOW/IRQ_TYPE_LEVEL_LOW/g
s/IRQT_HIGH/IRQ_TYPE_LEVEL_HIGH/g
s/IRQT_PROBE/IRQ_TYPE_PROBE/g
s/IRQT_NOEDGE/IRQ_TYPE_NONE/g
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the omap2_set_globals_{242x,243x,343x}() functions. These
functions are called early upon boot in the map_io() functions in the
board-specific init files.
This patch was accidentally left out of the earlier series.
This fixes omap2 booting as noted by Kyungmin Park <kmpark@infradead.org>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kyungmin Park <kmpark@infradead.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch changes 24xx to use new register access, except for clock
framework. Clock framework register access will get updates in the
next patch.
Note that board-*.c files change GPMC (General Purpose Memory Controller)
access to use gpmc_cs_write_reg() instead of accessing the registers
directly. The code also uses gpmc_fck instead of it's parent clock
core_l3_ck for GPMC clock.
The H4 board file also adds h4_init_flash() function, which specify the
flash start and end addresses.
Also note that sleep.S removes some unused registers addresses.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
smc91x is shared between many different platforms. Each platform needs
to specify the interrupt type, and in some cases the irq type depends
on more than just the build configuration - it depends on runtime
checks.
Rather than throwing this code into the SMC_IRQ_FLAGS definition, provide
a way for these flags to be passed via the IRQ resource itself.
Note that IRQF_TRIGGER_* constants are intentionally defined to correspond
with the IORESOURCE_IRQ_* interrupt type flags, in much the same way that
the low bits of PCI iomem resources correspond with the BAR flag bits.
Also provide a way to configure smc91x to read the IRQ flags from the
resource. Once all platforms have been converted over (signified
by all definitions of SMC_IRQ_FLAGS being -1) SMC_IRQ_FLAGS should
be removed.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Nicolas Pitre <nico@cam.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Lucas Woods <woodzy@gmail.com>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update Apollon board init to initialize NAND, USB,
and LEDs. Also configure GPMC memory for smc91x Ethernet.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix apollon board compiler error
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Untested, but this should fix up the bulk of the totally mechanical
issues, and should make the actual detail fixing easier.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Many files include the filename at the beginning, serveral used a wrong one.
Signed-off-by: Uwe Zeisberger <Uwe_Zeisberger@digi.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Apollon board MMC supports on OMAP2
TODO:
We have to check MMC on H4
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The irgflags consolidation did conflict with the ARM to generic IRQ
conversion and was not applied for ARM. Fix it up.
Use the new IRQF_ constants and remove the SA_INTERRUPT define
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Tony Lindgren
This patch syncs OMAP board support with linux-omap tree.
The highlights of the patch are:
- Add support for Nokia 770 by Juha Yrjola
- Add support for Samsung Apollon by Kyungmin Park
- Add support for Amstrad E3 videophone by Jonathan McDowell
- Remove board-netstar.c board support as requested by Ladislav Michl
- Do platform_device registration in board files by Komal Shah et al.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linus Torvalds