Commit Graph

60 Commits

Author SHA1 Message Date
Eric Miao 0cb0b0d3c6 [ARM] ohci-pxa27x: introduce pxa27x_clear_otgph()
Direct access to pxa27x specific register PSSR in a generic ohci driver
is no good, introduce pxa27x_clear_otgph() and move the implementation
into processor specific code.

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-10-07 19:12:58 +01:00
Russell King 5a89770daa Merge branches 'pxa-core' and 'pxa-machines' into pxa-all
Conflicts:

	arch/arm/mach-pxa/Kconfig
	arch/arm/mach-pxa/pxa25x.c
	arch/arm/mach-pxa/pxa27x.c
2008-10-07 19:08:56 +01:00
Eric Miao 5a3d965190 [ARM] pxa: better MFP low power state support for pxa25x/pxa27x
When configured as a specific low power state: MFP_LPM_DRIVE_LOW,
MFP_LPM_DRIVE_HIGH, the corresponding GPDR register bit during
low power mode shall be re-configured as output (if they are not
configured so), thus the PGSRx bits can output.

Create an additional low power values GPDR registers, and properly
save/restore the GAFR + GPDR registers when doing suspend/resume.

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-09-26 23:43:20 +01:00
Russell King 4104980a3c [ARM] pxa: Allow platforms to override PSPR setting
Currently, we set PSPR just before entering sleep mode.  However,
some platforms have different requirements for setting PSPR in
order to properly wake up.

Set PSPR earlier in the suspend cycle so that platforms can
change the setting by using a sysdev driver instead.

Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-09-09 16:32:52 +01:00
Mike Rapoport 9ba63c4fa1 [ARM] 5201/1: PXA3xx: Add support for power i2c bus
Add power I2C support for PXA3xx processors

Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-09-09 16:32:51 +01:00
Russell King afd2fc02ab Merge branch 'for-rmk' of git://git.kernel.org/pub/scm/linux/kernel/git/ycmiao/pxa-linux-2.6
Conflicts:

	arch/arm/mach-pxa/generic.c
	arch/arm/mach-pxa/pxa25x.c
	arch/arm/mach-pxa/pxa27x.c
	arch/arm/mach-pxa/pxa2xx.c
	arch/arm/mach-pxa/pxa3xx.c
	arch/arm/mach-pxa/reset.c
	arch/arm/mach-pxa/spitz.c
	arch/arm/mach-pxa/tosa.c
	drivers/watchdog/sa1100_wdt.c
2008-08-07 11:06:47 +01:00
Russell King a09e64fbc0 [ARM] Move include/asm-arm/arch-* to arch/arm/*/include/mach
This just leaves include/asm-arm/plat-* to deal with.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-08-07 09:55:48 +01:00
Russell King be50972935 [ARM] Remove asm/hardware.h, use asm/arch/hardware.h instead
Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-08-07 09:40:08 +01:00
Eric Miao 04fef228fb [ARM] pxa: introduce reset_status and clear_reset_status for driver's usage
Due to the problem of reset status bits being handled by different
registers between pxa2xx and pxa3xx, introduce a global reset_status
variable, initialized by SoC-specific code and later being used by
other drivers.

And also introduce clear_reset_status(), which is used to clear the
corresponding status bits. Pass RESET_STATUS_ALL to clear all bits.

Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-08-05 09:26:02 +08:00
Philipp Zabel 7a85762043 [ARM] 5120/1: pxa: correct platform driver names for PXA25x and PXA27x UDC drivers
The pxa2xx_udc.c driver is renamed to pxa25x_udc.c (the platform
driver name changes from pxa2xx-udc to pxa25x-udc) and the
platform driver name of pxa27x_udc.c is fixed to pxa27x-udc.
pxa_device_udc in devices.c is split into pxa25x and pxa27x flavors
and the pxa27x_device_udc is enabled in pxa27x.c.

Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Nicolas Pitre <nico@cam.org>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Including from Ian Molton:

Fixes for mistakes left over from the PXA2{5,7}X UDC split.

Signed-off-by: Ian Molton <spyro@f2s.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-07-09 21:30:13 +01:00
Russell King fdc614e873 Merge branches 'pxa-misc', 'pxa-pwm' and 'pxa-multi' into pxa 2008-07-09 20:56:05 +01:00
Philipp Zabel bc3a595988 [ARM] 5075/1: i2c-pxa: move i2c pin setup and PCFR_PI2CEN handling into arch/arm/mach-pxa
This fixes a build error introduced when the power manager
register definitions were moved into pxa2xx-regs.h.

Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-06-02 19:33:25 +01:00
Russell King 284d115ec9 [ARM] pxa: separate PXA25x and PXA27x UDC register definitions
The PXA25x and PXA27x USB device controller register definitions are
different.  Currently, they live side by side in pxa-regs.h, but only
one set is available depending on the setting of PXA25x or PXA27x.

This means that if we build to support both PXA25x and PXA27x, the
PXA27x definitions are unavailable, even to PXA27x specific code.

Remove these definitions from pxa-regs.h, and place them in separate
files.  Include these files where appropriate.

Note: according to the dependencies in drivers/usb/gadget/Kconfig,
we do not support the UDC on PXA27x nor PXA3xx CPUs, so remove the
platform devices from pxa27x.c and pxa3xx.c.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-05-19 16:25:58 +01:00
eric miao 75540c1ac3 [ARM] pxa: Add PXA support for PWM API
Patch mainly from Eric Miao, with minor edits by rmk.

Note: PWM0 and PWM2 share the same register I/O space and clock gating
on pxa{27x, 3xx}, thus PWM2 is treated in the driver as a child PWM of
PWM0. And this is also true for PWM1/3.

Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-05-19 16:25:39 +01:00
Russell King dc38e2ad53 [ARM] pxa: Fix RCSR handling
Related to d3930614e6.

RCSR is only present on PXA2xx CPUs, not on PXA3xx CPUs.  Therefore,
we should not be unconditionally writing to RCSR from generic code.

Since we now clear the RCSR status from the SoC specific PXA PM code
and before reset in the arch_reset() function, the duplication in
the corgi, poodle, spitz and tosa code can be removed.

Acked-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-05-08 18:04:02 +01:00
Robert Jarzmik 649de51b88 [ARM] 5027/1: Fixed random memory corruption on pxa suspend cycle.
Each time a pxa type cpu went in suspend, a portion of
kmalloc memory was corrupted.
The issue was an incorrect length allocation introduced by
the commit 711be5ccfe for
the save registers array (=> overflow).

Signed-off-by: Robert Jarzmik <rjarzmik@free.fr>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-05-04 11:06:05 +01:00
Russell King 1c104e0e4f [ARM] pxa: initialise PXA devices before platform init code
Initialise PXA devices before platform initialisation, so that
platforms can parent devices to these.

Acked-by: eric miao <ymiao3@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-19 11:29:09 +01:00
eric miao 3732098041 [ARM] pxa: add pxa27x_keypad device and pxa_set_keypad_info()
also update the clk definitions in pxa27x and pxa3xx.

Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-19 11:29:05 +01:00
eric miao c0a596d6a1 [ARM] pxa: allow dynamic enable/disable of GPIO wakeup for pxa{25x,27x}
Changes include:

1. rename MFP_LPM_WAKEUP_ENABLE into MFP_LPM_CAN_WAKEUP to indicate
   the board capability of this pin to wakeup the system

2. add gpio_set_wake() and keypad_set_wake() to allow dynamically
   enable/disable wakeup from GPIOs and keypad GPIO

   * these functions are currently kept in mfp-pxa2xx.c due to their
     dependency to the MFP configuration

3. pxa2xx_mfp_config() only gives early warning if MFP_LPM_CAN_WAKEUP
   is set on incorrect pins

So that the GPIO's wakeup capability is now decided by the following:

   a) processor's capability: (only those GPIOs which have dedicated
      bits within PWER/PRER/PFER can wakeup the system), this is
      initialized by pxa{25x,27x}_init_mfp()

   b) board design decides:
      - whether the pin is designed to wakeup the system (some of
        the GPIOs are configured as other functions, which is not
        intended to be a wakeup source), by OR'ing the pin config
        with MFP_LPM_CAN_WAKEUP

      - which edge the pin is designed to wakeup the system, this
        may depends on external peripherals/connections, which is
        totally board specific; this is indicated by MFP_LPM_EDGE_*

   c) the corresponding device's (most likely the gpio_keys.c) wakeup
      attribute:

Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-19 11:29:05 +01:00
eric miao b9e25aced3 [ARM] pxa: merge assignment of set_wake into pxa_init_{irq,gpio}()
To further clean up the GPIO and IRQ structure:

1. pxa_init_irq_gpio() and pxa_init_gpio() combines into a single
   function pxa_init_gpio()

2. assignment of set_wake merged into pxa_init_{irq,gpio}() as
   an argument

Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-19 11:29:04 +01:00
eric miao f6fb7af476 [ARM] pxa: integrate low IRQ chip (ICIP) and high IRQ chip (ICIP2) into one
This makes the code better organized and simplified a bit.  The change
will lose a bit of performance when performing IRQ ack/mask/unmask,but
that's not too much after checking the result binary.

This patch also removes the ugly #ifdef CONFIG_PXA27x .. #endif by
carefully not to access those pxa{27x,3xx} specific registers, this
is done by keeping an internal IRQ number variable.  The pxa-regs.h
is also modified so registers for IRQ > PXA_IRQ(31) are made public
even if CONFIG_PXA{27x,3xx} isn't defined (for pxa25x's sake)

The incorrect assumption in the original code that internal irq starts
from 0 is also corrected by comparing with PXA_IRQ(0).

"struct sys_device" for the IRQ are reduced into one single device on
pxa{27x,3xx}.

Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-19 11:29:04 +01:00
Mark Brown 27b98a671f [ARM] 4831/2: Add PXA2xx AC97 clocks to clock API
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-19 11:29:02 +01:00
eric miao 16dfdbf038 [ARM] pxa: introduce sysdev for GPIO register saving/restoring
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-02-04 13:17:33 +00:00
eric miao c016550490 [ARM] pxa: introduce sysdev for IRQ register saving/restoring
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-02-04 13:17:33 +00:00
Russell King 0ff66f0c7a Merge branch 'pxa-plat' into devel
* pxa-plat: (53 commits)
  [ARM] 4762/1: Basic support for Toradex Colibri module
  [ARM] pxa: fix mci_init functions returning -1
  [ARM] 4737/1: Refactor corgi_lcd to improve readability + bugfix
  [ARM] 4747/1: pcm027: support for pcm990 baseboard for phyCORE-PXA270
  [ARM] 4746/1: pcm027: network support for phyCORE-PXA270
  [ARM] 4745/1: pcm027: default configuration
  [ARM] 4744/1: pcm027: add support for phyCORE-PXA270 CPU module
  [NET] smc91x: Make smc91x use IRQ resource trigger flags
  [ARM] pxa: add default config for littleton
  [ARM] pxa: add basic support for Littleton (PXA3xx Form Factor Platform)
  [ARM] 4664/1: Add basic support for HTC Magician PDA phones
  [ARM] 4649/1: Base support for pxa-based Toshiba e-series PDAs.
  [ARM] pxa: skip registers saving/restoring if entering standby mode
  [ARM] pxa: fix PXA27x resume
  [ARM] pxa: Avoid fiddling with CKEN register on suspend
  [ARM] pxa: Add PXA3 standby code hooked into the IRQ wake scheme
  [ARM] pxa: Add zylonite MFP wakeup configurations
  [ARM] pxa: program MFPs for low power mode when suspending
  [ARM] pxa: make MFP configuration processor independent
  [ARM] pxa: remove un-used pxa3xx_mfp_set_xxx() functions
  ...

Conflicts:

	arch/arm/mach-pxa/ssp.c

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-01-28 13:21:38 +00:00
Mike Rapoport b7a3670131 i2c-pxa: Add polling transfer
Add polling I2C transfer implementation for PXA I2C. This is needed
for cases where I2C transactions have to occur at times interrups are
disabled.

Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-01-27 18:14:50 +01:00
Russell King fd8e7af8d0 [ARM] pxa: Avoid fiddling with CKEN register on suspend
The PXA manuals indicate that when in standby or sleep modes, clocks to
peripherals are shut off by the processor itself.  Eg:

PXA270 standby: "In standby mode, all clocks are disabled except those
 for the power manager and the RTC."

PXA270 sleep: "In sleep mode, all clocks are disabled to the processor
 and to all peripherals except the RTC."

PXA255 sleep: "In Sleep Mode, all processor and peripheral clocks are
 disabled, except the RTC."

Therefore, it should be safe to leave the clock enable register alone
prior to entering low power modes for these SoCs.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-01-26 15:07:57 +00:00
eric miao f79299ca85 [ARM] pxa: clean up pxa{27x,25x}_init_pm() to empty if CONFIG_PM not defined
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-01-26 15:07:54 +00:00
Russell King 8785a8fbd5 [ARM] pxa: move memory controller registers into pxa2xx-regs.h
PXA3 has a different memory controller from PXA2 platforms.  Avoid
clashing definitions by moving the PXA2 definitions to pxa2xx-regs.h

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-01-26 15:07:54 +00:00
eric miao ec68e45b75 [ARM] pxa: move pxa27x_device_ohci out of pxa27x.c for use with pxa3xx
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-01-26 15:07:54 +00:00
eric miao d8e0db1111 [ARM] pxa: add ssp devices and clk support for pxa25x/pxa27x/pxa3xx
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-01-26 15:07:51 +00:00
Russell King 03f5b2cee6 [ARM] pxa: avoid always registering MMC, I2C, IrDA and framebuffer devices
Only register the MMC, framebuffer, I2C and FICP devices when the
platform supplies the necessary platform data structures for the
devices.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-01-26 15:07:50 +00:00
eric miao 8854cb49a2 [ARM] 4652/1: pxa: fix a typo of pxa27x usb host clk definition
CKEN_USBHOST should be used instead of CKEN_USB for usb host

Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-11-26 14:38:51 +00:00
Rafael J. Wysocki 95d9ffbe01 PM: Move definition of struct pm_ops to suspend.h
Move the definition of 'struct pm_ops' and related functions from <linux/pm.h>
to <linux/suspend.h> .

There are, at least, the following reasons to do that:
* 'struct pm_ops' is specifically related to suspend and not to the power
  management in general.
* As long as 'struct pm_ops' is defined in <linux/pm.h>, any modification of it
  causes the entire kernel to be recompiled, which is unnecessary and annoying.
* Some suspend-related features are already defined in <linux/suspend.h>, so it
  is logical to move the definition of 'struct pm_ops' into there.
* 'struct hibernation_ops', being the hibernation-related counterpart of
  'struct pm_ops', is defined in <linux/suspend.h> .

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-18 14:37:18 -07:00
eric miao c95530c779 [ARM] 4560/1: pxa: move processor specific set_wake logic out of irq.c
a function pxa_init_irq_set_wake() was introduced, so that
processor specific code could install their own version

code setting PFER and PRER registers within pxa_gpio_irq_type
are removed, and the edge configuration is postponed to the
(*set_wake) and copies the GRER and GFER register, which will
always be set up correctly by pxa_gpio_irq_type()

Signed-off-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-10-12 21:15:33 +01:00
Russell King a88a447d44 [ARM] pxa: remove get_lcdclk_frequency_10khz()
get_lcdclk_frequency_10khz() is now redundant, remove it.  Hide
pxa27x_get_lcdclk_frequency_10khz() from public view.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-10-12 21:15:25 +01:00
Russell King 435b6e94b8 [ARM] pxa: Make STUART and FICP clocks available
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-10-12 21:15:14 +01:00
Russell King a6dba20c5c [ARM] pxa: introduce clk support for PXA SoC clocks
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-10-12 21:14:55 +01:00
Russell King 00dc4f949e [ARM] pxa: make pxa27x devices globally visible
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-10-12 21:14:53 +01:00
Russell King 15a4033354 [ARM] pxa: fix naming of memory/lcd/core clock functions
Rename pxa25x and pxa27x memory/lcd/core clock functions, and
select the correct version at run time.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-10-12 21:14:52 +01:00
Eric Miao b750a09385 [ARM] 4489/1: pxa: split pxa_cpu_suspend to processor specific ones
1. split pxa_cpu_suspend to pxa25x_cpu_suspend and pxa27x_cpu_suspend
   and make pxa25x_cpu_pm_enter() and pxa27x_cpu_pm_enter() to invoke
   the corresponding _suspend functions, thus remove all those ugly
   #ifdef .. #endif out of sleep.S

2. move the declarations of those suspend functions to pm.h

note: this is not a clean enough solution until all the pxa25x and
pxa27x specific part is further removed out of sleep.S, sleep.S is
supposed to contain generic code only

Signed-off-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-07-20 17:25:20 +01:00
Eric Miao 711be5ccfe [ARM] 4488/1: pxa: move pxa25x/pxa27x specific code out of pm.c
1. introduce a structure pxa_cpu_pm_fns for pxa25x/pxa27x specific
   operations as follows:

	struct pxa_cpu_pm_fns {
		int	save_size;
		void	(*save)(unsigned long *);
		void	(*restore)(unsigned long *);
		int	(*valid)(suspend_state_t state);
		void	(*enter)(suspend_state_t state);
	}

2. processor specific registers saving and restoring are performed
   by calling the corresponding (*save) and (*restore)

3. pxa_cpu_pm_fns->save_size should be initialized to the required
   size for processor specific registers saving, the allocated
   memory address will be passed to (*save) and (*restore)

   memory allocation happens early in pxa_pm_init(), and save_size
   should be assigned prior to this (which is usually true, since
   pxa_pm_init() happens in device_initcall()

4. there're some redundancies for those SLEEP_SAVE_XXX and related
   macros, will be fixed later, one way possible is for the system
   devices to handle the specific registers saving and restoring

Signed-off-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-07-20 17:25:10 +01:00
Eric Miao e09d02e123 [ARM] 4480/1: pxa: change the pxa device naming scheme
1. for common devices across all the pxa variants, the names
   are changed to be:
     "pxa_device_xxx"

2. for pxa25x or pxa27x specific devices, the names are
   changed to be:
     "pxa25x_device_xxx", or
     "pxa27x_device_xxx"

Signed-off-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-07-20 09:57:18 +01:00
Russell King 46c41e62a1 [ARM] pxa: move platform devices to separate header file
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-07-12 14:28:21 +01:00
Russell King 34f3231f43 [ARM] pxa: move device registration into CPU-specific file
This allows individual CPU support to determine which platform
devices should be registered.  Also fix a copy-n-paste bug in
the I2C power platform device entry.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-07-12 14:28:21 +01:00
Eric Miao f53f066c25 [ARM] 4451/1: pxa: make dma.c generic and remove cpu specific dma code
Since the number of dma channels varies between pxa25x and pxa27x, it
introduces some specific code in dma.c. This patch moves the specific
code to pxa25x.c and pxa27x.c and makes dma.c more generic.

1. add pxa_init_dma() for dma initialization, the number of channels
   are passed in by the argument

2. add a "prio" field to the "struct pxa_dma_channel" for the channel
   priority, and is initialized in pxa_init_dma()

3. use a general priority comparison with the channels "prio" field so
   to remove the processor specific pxa_for_each_dma_prio macro,  this
   is not lightning fast as the original one,  but it is acceptable as
   it happens when requesting dma, which is usually not so performance
   critical

Signed-off-by: eric miao <eric.miao@marvell.com>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-07-12 14:28:16 +01:00
Eric Miao cd49104d99 [ARM] 4450/1: pxa: add pxa25x_init_irq() and pxa27x_init_irq()
/* should be ok this time, I aligned this patch to your arm:pxa2.mbox */

1. move pxa25x specific IRQ initialization code to pxa25x_init_irq()
and pxa27x code to pxa27x_init_irq(), remove pxa_init_irq()

2. replace all pxa_init_irq() with their PXA25x or PXA27x specific
functions

Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-07-12 14:28:15 +01:00
Russell King 88dfe98c68 [ARM] pxa: Fix PXA27x suspend type validation, remove pxa_pm_prepare()
pxa_pm_prepare() tried to validate the suspend method type.  As
noted in previous commits:
	eb9289eb20
	9c372d06ce
	e8c9c50269

the checking of the suspend type in the 'prepare' method is the
wrong place to do this; use the 'valid' method instead.  This
means that pxa_pm_prepare() can be entirely removed.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-07-12 14:28:06 +01:00
Russell King e176bb05fe [ARM] pxa: move pm_ops structure into CPU specific files
Move the pm_ops structure into the PXA25x and PXA27x support
files.  Remove the old pxa_pm_prepare() function, and rename
the both pxa_cpu_pm_prepare() functions as pxa_pm_prepare().
We'll fix that later.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-07-12 14:28:05 +01:00
Richard Purdie 1f750a782c [ARM] 4458/1: pxa: Fix CKEN usage and hence fix pxa suspend/resume
The PXA CKEN changes broken syspend/resume on the pxa27x. This patch
corrects the problem and fixes another couple of bad references.

Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-07-02 13:39:37 +01:00