When disabling the controller, the specification says the register
NVME_REG_CC should be written and then driver needs to wait the
adapter to be ready, which is checked by reading another register
bit (NVME_CSTS_RDY). There's a timeout validation in this checking,
so in case this timeout is reached the driver gives up and removes
the adapter from the system.
After a firmware activation procedure, the PCI_DEVICE(0x1c58, 0x0003)
(HGST adapter) end up being removed if we issue a reset_controller,
because driver keeps verifying the NVME_REG_CSTS until the timeout is
reached. This patch adds a necessary quirk for this adapter, by
introducing a delay before nvme_wait_ready(), so the reset procedure
is able to be completed. This quirk is needed because just increasing
the timeout is not enough in case of this adapter - the driver must
wait before start reading NVME_REG_CSTS register on this specific
device.
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Dan writes:
"The removal of ->driverfs_dev in favor of just passing the parent
device in as a parameter to add_disk(). See below, it has received a
"Reviewed-by" from Christoph, Bart, and Johannes.
It is also a pre-requisite for Fam Zheng's work to cleanup gendisk
uevents vs attribute visibility [1]. We would extend device_add_disk()
to take an attribute_group list.
This is based off a branch of block.git/for-4.8/drivers and has
received a positive build success notification from the kbuild robot
across several configs.
[1]: "gendisk: Generate uevent after attribute available"
http://marc.info/?l=linux-virtualization&m=146725201522201&w=2"
This patch implements the RDMA host (initiator in SCSI speak) driver. It
can be used to connect to remote NVMe over Fabrics controllers over
Infiniband, RoCE or iWarp, and uses the existing NVMe core driver as well
a the new fabrics library.
To connect to all NVMe over Fabrics controller reachable on a given taget
port using RDMA/CM use the following command:
nvme connect-all -t rdma -a $IPADDR
This requires the latest version of nvme-cli with Fabrics support.
Signed-off-by: Jay Freyensee <james.p.freyensee@intel.com>
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Tested-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch implements the RDMA transport for the NVMe over Fabrics target,
which allows exporting NVMe over Fabrics functionality over RDMA fabrics
(Infiniband, RoCE, iWARP).
All NVMe logic is in the generic target and this module just provides a
small glue between it and the generic code in the RDMA subsystem.
Signed-off-by: Armen Baloyan <armenx.baloyan@intel.com>,
Signed-off-by: Jay Freyensee <james.p.freyensee@intel.com>
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Tested-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
NVMe over Fabrics RDMA transport defines a connection establishment
protocol over the RDMA connection manager. This header will be used by
both the host and target drivers to negotiate the connection
establishment parameters.
Signed-off-by: Jay Freyensee <james.p.freyensee@intel.com>
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Tested-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The nvme fabric (RDMA, FC, etc...) can introduce port, link or node
failures that may require a reconnect to re-establish the connection.
Add a new reconnecting state that will initially be used by the RDMA
driver.
Reviewed-by: Jay Freyensee <james.p.freyensee@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Tested-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The new nvme-rdma driver will need to reinitialize all the tags as part of
the error recovery procedure (realloc the tag memory region). Add a helper
in blk-mq for it that can iterate over all requests in a tagset to make
this easier.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Tested-by: Ming Lin <ming.l@ssi.samsung.com>
Reviewed-by: Stephen Bates <Stephen.Bates@pmcs.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Tested-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The __nvm_submit_ppa() function is not used outside lightnvm core.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
The passed by reference ppa list in nvm_set_rqd_list() is updated when
multiple planes are available. In that case, each PPA plane is
incremented when the device side PPA list is created. This prevents the
caller to rely on the PPA list to be unmodified after a call.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
The gen_mark_blk_bad function marks the wrong block when a block is on
a different channel. Fix the index calculation, so that it updates the
correct block.
Reported-by: Javier Gonzalez <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
The nvm_get_blk() function is called with rlun->lock held. This is ok
when the media manager implementation doesn't go out of its atomic
context. However, if a media manager persists its metadata, and
guarantees that the block is given to the target, this is no longer
a viable approach. Therefore, clean up the flow of rrpc_map_page,
and make sure that nvm_get_blk() is called without any locks acquired.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
The [get/put]_blk API enables targets to get ownership of blocks at
runtime. This information is currently not recorded on disk, and the
information is therefore lost on power failure. To restore the
metadata, the [get/put]_blk must persist its metadata. In that case,
we need to control the outer lock, so that we can disable them while
updating the on-disk metadata. Fortunately, the _unlocked versions can
be removed, which allows us to move the lock into the [get/put]_blk
functions.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
The ->list, ->open_list, and ->closed_list lists were previously used
for statistics. However, their usage have been removed, and thus these
can safely be removed.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
If a media manager tries to initialize it targets upon media manager
initialization, the media manager will need to know which target types
are available in LightNVM. The lists of which managers and target types
are available shares the same lock.
Therefore, on initialization, the nvm_lock is taken by LightNVM core,
which later leads to a deadlock when target types are enumerated by the
media manager.
Add an exclusive lock for target types to resolve this conflict.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
To enable persistent block management to easily control creation and
removal of targets, we move target management into the media
manager. The LightNVM core continues to maintain which target types are
registered, while the media manager now keeps track of its initialized
targets.
Two new callbacks for the media manager are introduced. create_tgt and
remove_tgt. Note that remove_tgt returns 0 on successfully removing a
target, and returns 1 if the target was not found.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
The generic manager should be called the general media manager, and
instead of using the rather long name of "gennvm" in front of each data
structures, use "gen" instead to shorten it. Update the description of
the media manager as well to make the media manager purpose clearer.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
The responsibility of the media manager is not to keep track of
open/closed blocks. This is better maintained within a target,
that already manages this information on writes.
Remove the statistics and merge the states NVM_BLK_ST_OPEN and
NVM_BLK_ST_CLOSED.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
A couple of small checkpatch fixups to stop it from complaining.
./drivers/lightnvm/core.c:360: WARNING: line over 80 characters
./drivers/lightnvm/core.c:360: ERROR: trailing statements should be on
next line
./drivers/lightnvm/core.c:503: WARNING: Block comments use a trailing */
on a separate line
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Checkpatch found two incidents where the type was preferred to be
written out in full.
./drivers/lightnvm/rrpc.h:184: WARNING: Prefer 'unsigned int' to bare
use of 'unsigned'
./drivers/lightnvm/rrpc.h:209: WARNING: Prefer 'unsigned int' to bare
use of 'unsigned'
./drivers/lightnvm/rrpc.c:51: WARNING: Prefer 'unsigned int' to bare use
of 'unsigned'
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Mark functions not used by ouside of thier implementing file as static.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
According to the OpenChannel SSD interface specification the NAND flash
MLC page pairing information's number of page page pairings field is the
first two bytes in the MLC Page Pairing data structure. The hardware's
data structure itself is little endian so annotate it as such, like the
rest of lighnvm's data structures.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
The ->reserved bit is not initialized when allocated on stack.
This may lead targets to misinterpret the PPA as cached.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Expose media manager mark_blk() to targets, as done for the rest of the
media manager callback functions.
Signed-off-by: Javier González <javier@cnexlabs.com>
Updated description
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Break the loop when rqd is not null to reduce
an unnecessary schedule.
Signed-off-by: Wenwei Tao <ww.tao0320@gmail.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
We accidentally return zero here when ERR_PTR(-ENOMEM) is intended.
Fixes: a07b4970f4 ('nvmet: add a generic NVMe target')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
CONFIG_NVME_TARGET has a correct CONFIG_CONFIGFS_FS dependency, but the
newly added NVME_TARGET_LOOP is missing this, resulting in a link
failure:
drivers/nvme/built-in.o: In function `nvmet_init_configfs':
loop.c:(.init.text+0x2a0): undefined reference to `config_group_init'
loop.c:(.init.text+0x2c0): undefined reference to `config_group_init_type_name'
loop.c:(.init.text+0x318): undefined reference to `configfs_register_subsystem'
drivers/nvme/built-in.o: In function `nvmet_exit_configfs':
loop.c:(.exit.text+0x9c): undefined reference to `configfs_unregister_subsystem'
This adds the same dependency here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 3a85a5de29 ("nvme-loop: add a NVMe loopback host driver")
Signed-off-by: Jens Axboe <axboe@fb.com>
We have assigned sb->block_size before the switch,
so remove the redundant one.
Reviewed-by: Coly Li <colyli@suse.de>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Acked-by: Eric Wheeler <bcache@lists.ewheeler.net>
Signed-off-by: Jens Axboe <axboe@fb.com>
There is no return in continue_at(), update the documentation.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Acked-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Cache_sb is not used in cache_alloc, and we have copied
sb info to cache->sb already, remove it.
Reviewed-by: Coly Li <colyli@suse.de>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch implements adds nvme-loop which allows to access local devices
exported as NVMe over Fabrics namespaces. This module can be useful for
easy evaluation, testing and also feature experimentation.
To createa nvme-loop device you need to configure the NVMe target to
export a loop port (see the nvmetcli documentaton for that) and then
connect to it using
nvme connect-all -t loop
which requires the very latest nvme-cli version with Fabrics support.
Signed-off-by: Jay Freyensee <james.p.freyensee@intel.com>
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch introduces a implementation of NVMe subsystems,
controllers and discovery service which allows to export
NVMe namespaces across fabrics such as Ethernet, FC etc.
The implementation conforms to the NVMe 1.2.1 specification
and interoperates with NVMe over fabrics host implementations.
Configuration works using configfs, and is best performed using
the nvmetcli tool from http://git.infradead.org/users/hch/nvmetcli.git,
which also has a detailed explanation of the required steps in the
README file.
Signed-off-by: Armen Baloyan <armenx.baloyan@intel.com>
Signed-off-by: Anthony Knapp <anthony.j.knapp@intel.com>
Signed-off-by: Jay Freyensee <james.p.freyensee@intel.com>
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The new NVMe over fabrics target will make use of this outside from a
module.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Periodic keep-alive is a mandatory feature in NVMe over Fabrics, and
optional in NVMe 1.2.1 for PCIe. This patch adds periodic keep-alive
sent from the host to verify that the controller is still responsive
and vice-versa. The keep-alive timeout is user-defined (with
keep_alive_tmo connection parameter) and defaults to 5 seconds.
In order to avoid a race condition where the host sends a keep-alive
competing with the target side keep-alive timeout expiration, the host
adds a grace period of 10 seconds when publishing the keep-alive timeout
to the target.
In case a keep-alive failed (or timed out), a transport specific error
recovery kicks in.
For now only NVMe over Fabrics is wired up to support keep alive, but
we can add PCIe support easily once controllers actually supporting it
become available.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Steve Wise <swise@chelsio.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
KAS: keep-alive support and granularity of kato in units of 100 ms
nvme_admin_keep_alive opcode: 0x18
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The NVMe over Fabrics library provides an interface for both transports
and the nvme core to handle fabrics specific commands and attributes
independent of the underlying transport.
In addition, the fabrics library adds a misc device interface that allow
actually creating a fabrics controller, as we can't just autodiscover
it like in the PCI case. The nvme-cli utility has been enhanced to use
this interface to support fabric connect and discovery.
Signed-off-by: Armen Baloyan <armenx.baloyan@intel.com>,
Signed-off-by: Jay Freyensee <james.p.freyensee@intel.com>,
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The NVMe over Fabrics specification defines a protocol interface and
related extensions to NVMe that enable operation over network protocols.
The NVMe over Fabrics specification has an NVMe Transport binding for
each NVMe Transport.
This patch adds the fabrics related definitions:
- fabric specific command set and error codes
- transport addressing and binding definitions
- fabrics sgl extensions
- controller identification fabrics enhancements
- discovery log page definition
Signed-off-by: Armen Baloyan <armenx.baloyan@intel.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Jay Freyensee <james.p.freyensee@intel.com>
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
- delete_controller: This attribute allows to delete a controller.
A driver is not obligated to support it (pci doesn't) so it is
created only if the driver supports it. The new fabrics drivers
will support it (essentialy a disconnect operation).
Usage:
echo > /sys/class/nvme/nvme0/delete_controller
- subsysnqn: This attribute shows the subsystem nqn of the configured
device. If a driver does not implement the get_subsysnqn method, the
file will not appear in sysfs.
- transport: This attribute shows the transport name. Added a "name"
field to struct nvme_ctrl_ops.
For loop,
cat /sys/class/nvme/nvme0/transport
loop
For RDMA,
cat /sys/class/nvme/nvme0/transport
rdma
For PCIe,
cat /sys/class/nvme/nvme0/transport
pcie
- address: This attributes shows the controller address. The fabrics
drivers that will implement get_address can show the address of the
connected controller.
example:
cat /sys/class/nvme/nvme0/address
traddr=192.168.2.2,trsvcid=1023
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Reviewed-by: Jay Freyensee <james.p.freyensee@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
NVMe over fabrics will use __nvme_submit_sync_cmd in the the
transport and require a few tweaks to it. For that we export it
and add a few more paramters:
1. allow passing a queue ID to the block layer
For the NVMe over Fabrics connect command we need to able to specify a
queue ID that we want to send the command on. Add a qid parameter to
the relevant functions to enable this behavior.
2. allow submitting at_head commands
In cases where we want to (re)connect to a controller
where we have inflight queued commands we want to first
connect and only then allow the other queued commands to
be kicked. This will prevents failures in controller resets
and reconnects.
3. allow passing flags to blk_mq_allocate_request
Both for Fabrics connect the the keep-alive feature in NVMe 1.2.1 we
want to be able to use reserved requests.
Reviewed-by: Jay Freyensee <james.p.freyensee@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Tested-by: Ming Lin <ming.l@ssi.samsung.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
For Fabrics we're not going through an intermediate reset state
(at least for now).
Reviewed-by: Jay Freyensee <james.p.freyensee@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
For some protocols like NVMe over Fabrics we need to be able to send
initialization commands to a specific queue.
Based on an earlier patch from Christoph Hellwig <hch@lst.de>.
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
[hch: disallow sleeping allocation, req_op fixes]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
MG_DISK_MAJ is defined as 0 so dynamic block major number
allocation is used by the driver and the assigned major
number is stored in host->major. This patch fixes error
path in mg_probe() to use host->major instead of using
MG_DISK_MAJ.
Cc: unsik Kim <donari75@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Now that all drivers that specify a ->driverfs_dev have been converted
to device_add_disk(), the pointer can be removed from struct gendisk.
Cc: Jens Axboe <axboe@fb.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
For block drivers that specify a parent device, convert them to use
device_add_disk().
This conversion was done with the following semantic patch:
@@
struct gendisk *disk;
expression E;
@@
- disk->driverfs_dev = E;
...
- add_disk(disk);
+ device_add_disk(E, disk);
@@
struct gendisk *disk;
expression E1, E2;
@@
- disk->driverfs_dev = E1;
...
E2 = disk;
...
- add_disk(E2);
+ device_add_disk(E1, E2);
...plus some manual fixups for a few missed conversions.
Cc: Jens Axboe <axboe@fb.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: James Bottomley <James.Bottomley@hansenpartnership.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In preparation for the removal of 'driverfs_dev' from 'struct gendisk'
use a local variable to track the parented vs un-parented case in
ubd_disk_register().
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In preparation for the removal of 'driverfs_dev' from 'struct gendisk',
carry this data in mmc_blk_data. It is used for registration of parent
disks and partitions.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In preparation for removing the ->driverfs_dev member of a gendisk, add
an api that takes the parent device as a parameter to add_disk(). For
now this maintains the status quo of WARN()ing on failure, but not
return a error code.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
crypto_alloc_hash returns an ERR_PTR(), not NULL.
Also reset peer_integrity_tfm to NULL, to not call crypto_free_hash()
on an errno in the cleanup path.
Reported-by: Insu Yun <wuninsu@gmail.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
For larger devices, the array of bitmap page pointers can grow very
large (8000 pointers per TB of storage).
For each activity log transaction, we need to flush the associated
bitmap pages to stable storage. Currently, we just "mark" the respective
pages while setting up the transaction, then tell the bitmap code to
write out all marked pages, but skip unchanged pages.
But one such transaction can affect only a small number of bitmap pages,
there is no need to scan the full array of several (ten-)thousand
page pointers to find the few marked ones.
Instead, remember the index numbers of the few affected pages,
and later only re-check those to skip duplicates and unchanged ones.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Also skip the message unless bitmap IO took longer than 5 ms.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This should silence a warning about an empty statement. Thanks to Fabian
Frederick <fabf@skynet.be> who sent a patch I modified to be smaller and
avoids an additional indent level.
Signed-off-by: Roland Kammerer <roland.kammerer@linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Guilherme G. Piccoli
Jens Axboe
Christoph Hellwig
Sagi Grimberg
Matias Bjørling
Johannes Thumshirn
Javier González
Javier González
Wenwei Tao
Dan Carpenter
Arnd Bergmann
Yijing Wang
Ming Lin
Bartlomiej Zolnierkiewicz
Dan Williams
Lars Ellenberg
Roland Kammerer