This patch enables the PPS system in the PHC framework, by enabling
the clock-out feature on the X540 device. Causes the SDP0 to be set as
a 1Hz clock. Also configures the timesync interrupt cause in order to
report each pulse to the PPS via the PHC framework, which can be used
for general system clock synchronization. (This allows a stable method
for tuning the general system time via the on-board SYSTIM register
based clock.)
Signed-off-by: Jacob E Keller <jacob.e.keller@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch enables hardware timestamping for use with PTP software by
extracting a ns counter from an arbitrary fixed point cycles counter.
The hardware generates SYSTIME registers using the DMA tick which
changes based on the current link speed. These SYSTIME registers are
converted to ns using the cyclecounter and timecounter structures
provided by the kernel. Using the SO_TIMESTAMPING api, software can
enable and access timestamps for PTP packets.
The SO_TIMESTAMPING API has space for 3 different kinds of timestamps,
SYS, RAW, and SOF. SYS hardware timestamps are hardware ns values that
are then scaled to the software clock. RAW hardware timestamps are the
direct raw value of the ns counter. SOF software timestamps are the
software timestamp calculated as close as possible to the software
transmit, but are not offloaded to the hardware. This patch only
supports the RAW hardware timestamps due to inefficiency of the SYS
design.
This patch also enables the PHC subsystem features for atomically
adjusting the cycle register, and adjusting the clock frequency in
parts per billion. This frequency adjustment works by slightly
adjusting the value added to the cycle registers each DMA tick. This
causes the hardware registers to overflow rapidly (approximately once
every 34 seconds, when at 10gig link). To solve this, the timecounter
structure is used, along with a timer set for every 25 seconds. This
allows for detecting register overflow and converting the cycle
counter registers into ns values needed for providing useful
timestamps to the network stack.
Only the basic required clock functions are supported at this time,
although the hardware supports some ancillary features and these could
easily be enabled in the future.
Note that use of this hardware timestamping requires modifying daemon
software to use the SO_TIMESTAMPING API for timestamps, and the
ptp_clock PHC framework for accessing the clock. The timestamps have
no relation to the system time at all, so software must use the posix
clock generated by the PHC framework instead.
Signed-off-by: Jacob E Keller <jacob.e.keller@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the VF sends a MACVLAN request with index of zero then it is not
actually trying to add a filter. Check the index value and only
indicate that operation is not allowed when the VF is actually trying
to add a filter.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The drop enable bit can be used to improve the performance of the adapter
in the case of multiple queues being present. This performance gain is due
to the fact that some slower CPUs can cause the FIFO to backfill preventing
faster CPUs from receiving additional work. By setting the drop enable bit
we prevent this and instead just drop the packets that would have been
bound for the slower CPU.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change cleans up the logic in the priority based flow control
configuration routines. Both the 82599 and 82598 based routines perform
similar functions however they are both arranged completely differently.
This patch goes over both of them to clean up the code.
In addition I am dropping the ixgbe_fc_pfc flow control mode and instead
just replacing it with checks for if priority flow control is enabled.
This allows us to maintain some of the link flow control information which
allows for an easier transition between link and priority flow control.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previously we would get a mailbox error and still process the message.
Instead we should exit on error.
In addition we should also be flushing the ACK of the message so that we
can guarantee that the other end is aware we have received the message
while we are processing it.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Current igb outputs registers related to TX/RX queues(ex. RDT, RDH, TDT, TDH).
But it thinks the number of RX/TX queues is 4. But 82576 has 16 RX/TX queues.
This patch modifies igb to output the rest of the registers if the device is
82576.
Signed-off-by: Koki Sanagi <sanagi.koki@jp.fujitsu.com>
Acked-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.
Done via cocci script:
$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
- !compare_ether_addr(a, b)
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- compare_ether_addr(a, b)
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) == 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) != 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) == 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) != 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !!ether_addr_equal(a, b)
+ ether_addr_equal(a, b)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
spatch/coccinelle isn't perfect. It doesn't understand
__aligned(x) and doesn't convert functions it can't parse.
Convert the remaining compare_ether_addr uses.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.
I removed a conversion from scan.c/cmp_bss_core
that appears to be a sorting function.
Done via cocci script:
$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
- !compare_ether_addr(a, b)
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- compare_ether_addr(a, b)
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) == 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) != 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) == 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) != 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !!ether_addr_equal(a, b)
+ ether_addr_equal(a, b)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.
Done via cocci script:
$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
- !compare_ether_addr(a, b)
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- compare_ether_addr(a, b)
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) == 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) != 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) == 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) != 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !!ether_addr_equal(a, b)
+ ether_addr_equal(a, b)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
spatch/coccinelle isn't perfect. It doesn't understand
__aligned(x) and doesn't convert functions it can't parse.
Convert the remaining compare_ether_addr uses.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.
Done via cocci script:
$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
- !compare_ether_addr(a, b)
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- compare_ether_addr(a, b)
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) == 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) != 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) == 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) != 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !!ether_addr_equal(a, b)
+ ether_addr_equal(a, b)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.
Done via cocci script:
$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
- !compare_ether_addr(a, b)
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- compare_ether_addr(a, b)
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) == 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) != 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) == 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) != 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !!ether_addr_equal(a, b)
+ ether_addr_equal(a, b)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.
Done via cocci script:
$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
- !compare_ether_addr(a, b)
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- compare_ether_addr(a, b)
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) == 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) != 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) == 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) != 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !!ether_addr_equal(a, b)
+ ether_addr_equal(a, b)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.
Done via cocci script:
$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
- !compare_ether_addr(a, b)
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- compare_ether_addr(a, b)
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) == 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) != 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) == 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) != 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !!ether_addr_equal(a, b)
+ ether_addr_equal(a, b)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.
Done via cocci script:
$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
- !compare_ether_addr(a, b)
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- compare_ether_addr(a, b)
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) == 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) != 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) == 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) != 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !!ether_addr_equal(a, b)
+ ether_addr_equal(a, b)
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.
Done via cocci script:
$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
- !compare_ether_addr(a, b)
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- compare_ether_addr(a, b)
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) == 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) != 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) == 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) != 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !!ether_addr_equal(a, b)
+ ether_addr_equal(a, b)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.
Done via cocci script:
$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
- !compare_ether_addr(a, b)
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- compare_ether_addr(a, b)
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) == 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) != 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) == 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) != 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !!ether_addr_equal(a, b)
+ ether_addr_equal(a, b)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a boolean function to check if 2 ethernet addresses
are the same.
This is to avoid any confusion about compare_ether_addr
returning an unsigned, and not being able to use the
compare_ether_addr function for sorting ala memcmp.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During merge of net to net-next the changes in patch:
e1000e: Fix default interrupt throttle rate not set in NIC HW
got munged in param.c of the e1000e driver. This rectifies the
merge issues.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
can be used e.g. for ingress traffic policing or
to detect when a host/port consumes more bandwidth than expected.
This is done by optionally making cost to mean
"cost per 16-byte-chunk-of-data" instead of "cost per packet".
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
followup patch would bloat main match function too much.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The target allows you to create rules in the "raw" and "mangle" tables
which set the skbuff mark by means of hash calculation within a given
range. The nfmark can influence the routing method (see "Use netfilter
MARK value as routing key") and can also be used by other subsystems to
change their behaviour.
[ Part of this patch has been refactorized and modified by Pablo Neira Ayuso ]
Signed-off-by: Hans Schillstrom <hans.schillstrom@ericsson.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch adds the flags parameter to ipv6_find_hdr. This flags
allows us to:
* know if this is a fragment.
* stop at the AH header, so the information contained in that header
can be used for some specific packet handling.
This patch also adds the offset parameter for inspection of one
inner IPv6 header that is contained in error messages.
Signed-off-by: Hans Schillstrom <hans.schillstrom@ericsson.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
During merge of net to net-next the changes in patch:
e1000e: Fix default interrupt throttle rate not set in NIC HW
got munged in param.c of the e1000e driver. This rectifies the
merge issues.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes ip_queue support which was marked as obsolete
years ago. The nfnetlink_queue modules provides more advanced
user-space packet queueing mechanism.
This patch also removes capability code included in SELinux that
refers to ip_queue. Otherwise, we break compilation.
Several warning has been sent regarding this to the mailing list
in the past month without anyone rising the hand to stop this
with some strong argument.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Explicit helper attachment via the CT target is broken with NAT
if non-standard ports are used. This problem was hidden behind
the automatic helper assignment routine. Thus, it becomes more
noticeable now that we can disable the automatic helper assignment
with Eric Leblond's:
9e8ac5a netfilter: nf_ct_helper: allow to disable automatic helper assignment
Basically, nf_conntrack_alter_reply asks for looking up the helper
up if NAT is enabled. Unfortunately, we don't have the conntrack
template at that point anymore.
Since we don't want to rely on the automatic helper assignment,
we can skip the second look-up and stick to the helper that was
attached by iptables. With the CT target, the user is in full
control of helper attachment, thus, the policy is to trust what
the user explicitly configures via iptables (no automatic magic
anymore).
Interestingly, this bug was hidden by the automatic helper look-up
code. But it can be easily trigger if you attach the helper in
a non-standard port, eg.
iptables -I PREROUTING -t raw -p tcp --dport 8888 \
-j CT --helper ftp
And you disabled the automatic helper assignment.
I added the IPS_HELPER_BIT that allows us to differenciate between
a helper that has been explicitly attached and those that have been
automatically assigned. I didn't come up with a better solution
(having backward compatibility in mind).
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This refreshes the "timeout" attribute in existing expectations if one is
given.
The use case for this would be for userspace helpers to extend the lifetime
of the expectation when requested, as this is not possible right now
without deleting/recreating the expectation.
I use this specifically for forwarding DCERPC traffic through:
DCERPC has a port mapper daemon that chooses a (seemingly) random port for
future traffic to go to. We expect this traffic (with a reasonable
timeout), but sometimes the port mapper will tell the client to continue
using the same port. This allows us to extend the expectation accordingly.
Signed-off-by: Kelvie Wong <kelvie@ieee.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
To build ip_vs as a module sysctl_rmem_max and sysctl_wmem_max
needs to be exported.
The dependency was added by "ipvs: wakeup master thread" patch.
Signed-off-by: Hans Schillstrom <hans.schillstrom@ericsson.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Functions not referenced outside of a source file should be marked
static to prevent it from being exposed globally.
This quiets the sparse warnings:
warning: symbol '__ipvs_proto_data_get' was not declared. Should it be static?
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Functions not referenced outside of a source file should be marked
static to prevent it from being exposed globally.
This quiets the sparse warnings:
warning: symbol 'ip_vs_ftp_init' was not declared. Should it be static?
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
cp->flags is marked volatile but ip_vs_bind_dest
can safely modify the flags, so save some CPU cycles by
using temp variable.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Allow master and backup servers to use many threads
for sync traffic. Add sysctl var "sync_ports" to define the
number of threads. Every thread will use single UDP port,
thread 0 will use the default port 8848 while last thread
will use port 8848+sync_ports-1.
The sync traffic for connections is scheduled to many
master threads based on the cp address but one connection is
always assigned to same thread to avoid reordering of the
sync messages.
Remove ip_vs_sync_switch_mode because this check
for sync mode change is still risky. Instead, check for mode
change under sync_buff_lock.
Make sure the backup socks do not block on reading.
Special thanks to Aleksey Chudov for helping in all tests.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Tested-by: Aleksey Chudov <aleksey.chudov@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Add two new sysctl vars to control the sync rate with the
main idea to reduce the rate for connection templates because
currently it depends on the packet rate for controlled connections.
This mechanism should be useful also for normal connections
with high traffic.
sync_refresh_period: in seconds, difference in reported connection
timer that triggers new sync message. It can be used to
avoid sync messages for the specified period (or half of
the connection timeout if it is lower) if connection state
is not changed from last sync.
sync_retries: integer, 0..3, defines sync retries with period of
sync_refresh_period/8. Useful to protect against loss of
sync messages.
Allow sysctl_sync_threshold to be used with
sysctl_sync_period=0, so that only single sync message is sent
if sync_refresh_period is also 0.
Add new field "sync_endtime" in connection structure to
hold the reported time when connection expires. The 2 lowest
bits will represent the retry count.
As the sysctl_sync_period now can be 0 use ACCESS_ONCE to
avoid division by zero.
Special thanks to Aleksey Chudov for being patient with me,
for his extensive reports and helping in all tests.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Tested-by: Aleksey Chudov <aleksey.chudov@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
High rate of sync messages in master can lead to
overflowing the socket buffer and dropping the messages.
Fixed sleep of 1 second without wakeup events is not suitable
for loaded masters,
Use delayed_work to schedule sending for queued messages
and limit the delay to IPVS_SYNC_SEND_DELAY (20ms). This will
reduce the rate of wakeups but to avoid sending long bursts we
wakeup the master thread after IPVS_SYNC_WAKEUP_RATE (8) messages.
Add hard limit for the queued messages before sending
by using "sync_qlen_max" sysctl var. It defaults to 1/32 of
the memory pages but actually represents number of messages.
It will protect us from allocating large parts of memory
when the sending rate is lower than the queuing rate.
As suggested by Pablo, add new sysctl var
"sync_sock_size" to configure the SNDBUF (master) or
RCVBUF (slave) socket limit. Default value is 0 (preserve
system defaults).
Change the master thread to detect and block on
SNDBUF overflow, so that we do not drop messages when
the socket limit is low but the sync_qlen_max limit is
not reached. On ENOBUFS or other errors just drop the
messages.
Change master thread to enter TASK_INTERRUPTIBLE
state early, so that we do not miss wakeups due to messages or
kthread_should_stop event.
Thanks to Pablo Neira Ayuso for his valuable feedback!
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
As the goal is to mirror the inactconns/activeconns
counters in the backup server, make sure the cp->flags are
updated even if cp is still not bound to dest. If cp->flags
are not updated ip_vs_bind_dest will rely only on the initial
flags when updating the counters. To avoid mistakes and
complicated checks for protocol state rely only on the
IP_VS_CONN_F_INACTIVE bit when updating the counters.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Tested-by: Aleksey Chudov <aleksey.chudov@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Initially, when the synced connection is created we
use the forwarding method provided by master but once we
bind to destination it can be changed. As result, we must
update the application and the transmitter.
As ip_vs_try_bind_dest is called always for connections
that require dest binding, there is no need to validate the
cp and dest pointers.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
As the IP_VS_CONN_F_INACTIVE bit is properly set
in cp->flags for all kind of connections we do not need to
add special checks for synced connections when updating
the activeconns/inactconns counters for first time. Now
logic will look just like in ip_vs_unbind_dest.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
As IP_VS_CONN_F_NOOUTPUT is derived from the
forwarding method we should get it from conn_flags just
like we do it for IP_VS_CONN_F_FWD_MASK bits when binding
to real server.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Use GFP_KERNEL instead of GFP_ATOMIC when registering an ipvs protocol.
This is safe since it will always run from a process context.
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Schedulers are initialized and bound to services only
on commands.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Hans Schillstrom <hans@schillstrom.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Schedulers are initialized and bound to services only
on commands.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Hans Schillstrom <hans@schillstrom.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Schedulers are initialized and bound to services only
on commands.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Hans Schillstrom <hans@schillstrom.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Schedulers are initialized and bound to services only
on commands.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Hans Schillstrom <hans@schillstrom.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Schedulers are initialized and bound to services only
on commands.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Hans Schillstrom <hans@schillstrom.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Jacob E Keller
Greg Rose
Alexander Duyck
Koki Sanagi
Jeff Kirsher
Joe Perches
David S. Miller
Florian Westphal
Hans Schillstrom
Pablo Neira Ayuso
Kelvie Wong
H Hartley Sweeten
Julian Anastasov
Sasha Levin