Commit Graph

7 Commits

Author SHA1 Message Date
David Brownell 82c54f864f [AVR32] ngw100 i2c-gpio tweaks
Make the NGW100 bitbang i2c use open drain signaling.

Also, speed it up, so it's closer to 100 kHz ... the code paths seem
to be long enough that the udelay isn't dominating bit times.  The
peak bit rate I observed was around 125 kHz, but that's with large
delays (usually before ACK/NAK) which hold the overall rate down to
around 80 kHz (call it 100 usec/byte on average).

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2007-10-11 13:32:55 +02:00
Kristoffer Nyborg Gregertsen af8184718a [AVR32] SMC configuration in clock cycles
This patch makes the SMC configuration take timings in clock cycles
instead of nanoseconds. A function to calculate timings in clock
cycles is added.

This patch removes the rounding troubles of the previous SMC
configuration method.

[hskinnemoen@atmel.com: fix atstk1002/atngw100 flash config]
Signed-off-by: Kristoffer Nyborg Gregertsen <gregerts@stud.ntnu.no>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2007-10-11 13:32:49 +02:00
Haavard Skinnemoen 6fcf061511 [AVR32] Wire up USBA device
Implement at32_add_device_usba() and use it to wire up the USBA device
on ATSTK1000 and ATNGW100.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2007-10-11 11:40:27 +02:00
Haavard Skinnemoen 54bb69e250 [AVR32] Wire up i2c-gpio on the ATNGW100 board
The NGW100 has a board controller which is hooked up to the TWI lines
on AP7000. Since the TWI driver isn't in mainline, use the i2c-gpio
driver in the mean time.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2007-08-15 16:36:55 +02:00
David Brownell f9f451d9ca leds: leds-gpio for ngw100
Add GPIO leds to the NGW100 platform and its defconfig.
Access through /sys/class/leds/{a,b,sys}/* files; one
defaults to a heartbeat.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
2007-07-16 01:15:51 +01:00
ben.nizette@iinet.net.au 7f8b9acae8 [AVR32] NGW100, Remove relics of the old USART mapping scheme
USART mapping used to be accomplished by the manual filling of
at32_usart_map[] and at32_nr_usarts.  This has now been replaced
with at32_map_usart() so we can remove these variables.

Signed-off-by: Ben Nizette <ben.nizette@iinet.net.au>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2007-06-23 14:52:58 +02:00
Haavard Skinnemoen 9ca20a8366 [AVR32] Board code for ATNGW100
Add board code and defconfig for the ATNGW100 Network Gateway kit.
For more information about this board, see

http://www.atmel.com/dyn/products/tools_card.asp?tool_id=4102

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2007-04-27 13:44:15 +02:00